Copyright: Valiant Communications Limited - 2010Slide 1 Ethernet over E1 (FE1) Product Presentation...

Copyright: Valiant Communications Limited - 2010 Slide 1

Ethernet over E1 (FE1)

Ethernet over E1 (FE1)Ethernet over E1 (FE1)

Product PresentationProduct Presentation

Updated: 29 April, 2010



Product Overview Ethernet over E1 Converter provides the user a facility to transport Ethernet

(multiple LANs) over an E1 link.

Very Compact and Low cost.

Converts and transports Ethernet sites over an E1 link.

The device can effectively utilize the redundant bandwidth of telecom

operators' existing TDM network to transport Ethernet data with low

investment.

Optional powers 220V AC and -48V DC.

Provides 120 Ohms – RJ45 and 75 Ohms - BNC E1 interface in the same

box (user selectable).

Plug and Play.



The maximum transmission rate of Ethernet data over E1 links is 2.048 Mbit/s.

Supporting 1600 frames, accordance with Interior Switching Link (ISL) Protocol.

Supports unframed, framed and multi framed E1 transmission mode.

Supporting local E1 port loop-back.

The Ethernet Port is self-adaptive to crossover or shoot-through (Straight /

Parallel) cable to avoid the trouble of re-wiring.

Ethernet negotiation function. Supports 10M/100M and working modes of both

full-duplex and semi-duplex.

Transparently transmits ultra-long frames stipulated in IEEE 802.1Q, and

supports Ethernet switches with VLAN function.

Transport the DATA transparently (No configuration required).

Visual alarms (LEDs) on front panel.

Features and Highlights



Features and Highlights Imbedded, dynamic Ethernet MAC address list (1024 addresses), and filter

function for local data frames Can support multiple LANs of different network

addresses.

Optional powers 220V AC and -48V DC.

Supported fractional E1. E1 Bandwidth can be adjusted from 64 Kbps to 2048

Kbps and selected in N*64Kbps format.

Provides 120 Ohms – RJ45 and 75 Ohms - BNC E1 interface in the same box

(user selectable).

Configurable Ethernet port speed (10 /100) and mode (Half / Full Duplex).

Ethernet port mode status (LEDs).

Plug and Play.

Very compact and low power consumption.



Applications This equipment may be used for the following purposes:

Bridging Ethernet LANs over existing TDM (E1) telecom network.

Extending Ethernet Networks utilizing TDM (E1) landline based telecom

infrastructure.

Using telecom network of E1s / PDH / SDH Microwave etc.

Carrying E1s to transport Ethernet data.

In all these cases the equipment be always installed and used in pairs, with

one terminal being installed at either end (each side) of the network.



Application Diagram

E1 Link

LAN

LAN

ROUTER

ROUTER

TDM

Network

E1 Link

Ethernet over E1

(FE1)

LAN

LAN

ROUTER

ROUTER

Ethernet over E1

(FE1)



Front Panel Description



Back Panel Description

Ethernet over E1 (220V AC Mains input)

Ethernet over E1 (-48V DC Mains input)



Bottom Panel Description

Timeslot selection for the fraction E1 is given in the bottom of the equipment



Thank you for your attentionThank you for your attention

For more details visit us at our Website at

http://www.valiantcom.com

U.K.

Valiant Communications (UK) Ltd1, Acton Hill Mews,310-328 Uxbridge Road,London W3 9QN, United Kingdom

INDIA

Valiant Communications Limited71/1, Shivaji Marg, New Delhi - 110015, India

SOLD BY:

Aries Telecom and Trading Corp. FZEPO Box 31291, Al-Jazeera Al-Hamra, Ras Al Khaimah, U.A.E. Ph: +971 56 1361308E-mail: [email protected]: http://www.ariestelecom.com

U.S.A.

Valcomm Technologies Inc.4000 Ponce de Leon, Suite 470Coral Gables, FL 33146United States of America

Website: http://www.valiantcom.com

Website: http://www.valiantcom.com Website: http://www.valiantcom.com

Copyright: Valiant Communications Limited - 2010Slide 1 Ethernet over E1 (FE1) Product Presentation...

Documents

Transcript of Copyright: Valiant Communications Limited - 2010Slide 1 Ethernet over E1 (FE1) Product Presentation...