CONSTRUCTION PRODUCTS CATALOGUE - Plucka · PDF fileconstruction products 3 the complete range...

MANUFACTURER AND DISTRIBUTOR OF INDUSTRY LEADING BRANDS

CONSTRUCTION PRODUCTS CATALOGUE

© Copyright 2014 Parchem Construction Supplies Pty LimitedThis publication is copyright. All rights are reserved.Reproduction in whole or in part is prohibited without written permission.Application details are provided as a suggestion only of intended use.This catalogue is produced as a guide to the product range. Some items may not be available at all outlets.Owing to a continual product improvement, designs & specifications may be subject to change without notice.

MANUFACTURER AND DISTRIBUTOR OF INDUSTRY LEADING BRANDS

CONSTRUCTION PRODUCTS 3

THE COMPLETE RANGE OF PRODUCTS AND SOLUTIONS FOR THE CONSTRUCTION INDUSTRY…

C O N T E N T S

CONTENTS

Concrete Placement 6

Bar Chairs 7

Concrete Jointing 8-11

Primers 12

Concrete Sealants 12-13

Curing Compounds 16

Evaporation Retarders 17

Release Agents 17

Flooring 18-21

Decorative Coatings 22

Concrete Sealers 22-23

Waterproofing 26-35

Concrete Repair Products 38-41

Protective Coatings 42

Corrosion Protection 43

Grouting 46-47

Chemical Anchors 48

PARCHEM CONSTRUCTION SUPPLIES PTY LTD ABN 80 069 961 9684

CONCRETE PLACEMENT & JOINTING


FORMWORK

PART ID DIMENSIONS MATERIAL

FW2412512G 2.4m x 125mm 12mm Chamfer Galvanised












MESH

PART ID DESCRIPTION

MS3001 MESH SL62 6.0M X 2.4M

MS3002 UTE SIZE MESH SL62DM 4.0M X 2.4M

MS3003 MESH SL72 6.0M X 2.4M

MS3004 UTE SIZE MESH SL72DM 4.0M X 2.4M

MS3005 MESH FULL SL82 6.0M X 2.4M

MS3006 MESH SL92 6.0M X 2.4M

MS3010 MESH FULL SL81 6.0M X 2.4M

MS3031 MESH SL52 6.0M X 2.4M

MS3045 MESH SL102 6.0M X 2.4M

MS3068 UTE SIZE MESH SL82 4.0M X 2.4M

CONCRETE FIBRE SPACERS

PART ID MAX FRANK CODE CONCRETE COVER SACK CONT. PIECES

711551 AO3572 35/40/50 250

711550 AO4573 45/55/60 125

Note: spacers available with tie wire on request.Other concrete spacers are available on request. Please contact Parchem for details.

AO

FORM PLY

PART ID DESCRIPTIONS DIMENSIONS PACK QTY

PLY2412171F11 F11 Good One Side 2400 x 1200 x 17mm 50

PLY2412171F14 F14 Good One Side 2400 x 1200 x 17mm 50

PLY2412172F11 F11 Good Two Sides 2400 x 1200 x 17mm 50

PLY2412172F14 F14 Good Two Sides 2400 x 1200 x 17mm 50

PLY2412172F11IMP General Purpose Imported Formply 2400 x 1200 x 17mm 50

FCMS

PART ID COVER PACK QTY

FCM20 20mm 100

FCM25 25mm 100

FCM30 30mm 100

FCM35 35mm 100

FCM40 40mm 100

FCM50 50mm 100

FCM60 60mm 100

FCM65 65mm 100

FCM75 75mm 100

EXTENSIONS


FCMX25 25mm 100

FCMX30 30mm 100

FCMX50 50mm 100

FCMX60 60mm 100

FCMX65 65mm 100

FCMX70 70mm 100

BASES


FWBASE015 +15mm 100

FWBASE025 +25mm 100

SLAB ON GROUND BASES


FCBASE +2mm 100

FAST CLIP MESH SUPPORTS (FCM)

20mm to 70mm

C O N C R E T E P L A C E M E N T


C O N C R E T E P L A C E M E N T

15-75mm

30mmFAST CLIP ON BAR CHAIRSSmall Head 4mm - 20mm bar.

TOP DECK CHAIRS

ABBOTTOM DECK CHAIRSMesh & large bar supports.

SLAB ON GROUND CHAIRSClip on versions available.

FERRULE SUPPORT CHAIRS

WIRE CHAIR (3 & 4 LEG PLASTIC TIPPED)


FCB15 15mm 100

FCB20 20mm 100

FCB25 25mm 100

FCB30 30mm 100

FCB35 35mm 100

FCB40 40mm 100

FCB45 45mm 100

FCB50 50mm 100

FCB60 60mm 100

FCB65 65mm 100

FCB75 75mm 100

PART ID A B PACK QTY

BPDST65/75 65 75 50

BPDST90/100 90 100 50

BPDST110/120 110 120 50

BPDST130/140 130 140 50

BPDST150/160 150 160 50

BPDST170/180 170 180 50

BPDST190/200 190 200 50

BASES


BCBASE 130 x 2mm 100


BPDS15/20 15 20 100

BPDS25/30 25 30 100

BPDS35/40 35 40 100

BPDS45/50 45 50 100

PANEL CHAIRSProvides covers of 50/60mm and 65/75mm to suit popular panel thicknesses of 100,120,130,150 and 170mm.

PART ID COVER PALLET QTY

FCB15 15mm 5000

FCB20 20mm 5000


BC25/40 25 40 50

BC50/65 50 65 50

BC75/90 75 90 50

BC85/100 85 100 50


FWSC125/96 125 96 50

FWSC150/96 150 96 50

FWSC175/96 175 96 50

FWSC180/96 180 96 50

FWSC200/96 200 96 50

PART ID SIZE

RB-TH20 20 to 400mm

BA

B

A


C O N C R E T E J O I N T I N G

DIAMOND DOWELS

PART ID DESCRIPTION PACKAGING

2500255 1 PIECE DIAMOND DOWEL 6MM 25/carton

2501187 DIAMOND DOWEL 6mm BLACK BULK PACK 500 per pallet

2500256 DIAMOND DOWEL 6MM GALVANISED 25/carton

2501190 DIAMOND DOWEL 6mm GALV BULK PACK 500 per pallet

2500258 DIAMOND DOWEL 6MM STAINLESS STEEL 25/carton

2500250 1 PIECE DIAMOND DOWEL 10MM 15/carton

2501192 DIAMOND DOWEL 10mm BLACK BULK PACK 500 per pallet

2500257 DIAMOND DOWEL 10MM GALVANISED 15/carton

2501195 DIAMOND DOWEL 10mm GALV BULK PACK 500 per pallet

2500259 DIAMOND DOWEL 10MM STAINLESS STEEL 15/carton

CRACK INDUCERS

PART ID DESCRIPTION

2500175 25MM GROUND CRACK INDUCER X 3M

2500180 50MM GROUND CRACK INDUCER X 3M

DOWELS MASTER

PART ID DESCRIPTION PACKAGING

2500284 DOWELMASTER 16MM 100/carton

2500285 DOWELMASTER 20MMX260 100/carton

2500289 DOWELMASTER 16MM N. PLATE 100/carton

2500290 DOWELMASTER 20MM N. PLATE 100/carton

PECAFORMSacrificial composite formwork system, sold per each, priced per each.

PART ID DESCRIPTION

2500649 PECAFORM 2.25MX.6M EACH

2500650 PECAFORM 2.25MX.9M EACH

2500651 PECAFORM 2.4MX1.2M EACH



PVC WATERSTOPSCentrally and externally placed, pvc waterstop profiles for use in cast in-situ concrete.

PART ID DESCRIPTION

720301 SUPERCAST H/F 150MMX15M ROLL



720330 SUPERCAST R/G 'R' 150MMX12M ROLL

720340 SUPERCAST R/G 'R' 200MMX12M ROLL

720350 SUPERCAST R/G ‘S’ 250MMX12M ROLL

720360 SUPERCAST R/G ‘R’ 250MMX12M ROLL

CRACK-A-JOINTPre-formed surfaced applied metal crack inducing strip, 3m lengths available plain or capped, sold in lengths only.

PART ID DESCRIPTION

2200116 CRACK A JOINT PLAIN 25MM X 3M

2200117 CRACK A JOINT GREY 25MM X 3M

2200121 CRACK A JOINT BLACK 25MM X 3M

2200122 CRACK A JOINT TERRACOTTA 25MM X 3M

2200123 CRACK A JOINT SANDSTONE 25MM X 3M

2200118 CRACK A JOINT PLAIN 45MM X 3M

2200119 CRACK A JOINT GREY 45MM X 3M

2200126 CRACK A JOINT BLACK 45MM X 3M

2200127 CRACK A JOINT TERRACOTTA 45MM X 3M

2200128 CRACK A JOINT SANDSTONE 45MM X 3M

KEYJOINTSacrificial metal keyjoint system for on ground slabs

USES

Preformed metal Keyjoint is used to form “keyways” along construction joints between adjacent pavement slabs enabling loads to be transferred from slab to slab while allowing differential movement between them. Keyjoints are suitable for forming construction joints in concrete pavements subject to light vehicle traffic, light industrial pavements, driveways, pedestrian walkways.

PART ID DESCRIPTION

2500490 METAL KEYJOINT100MM/3M LENG

2500495 METAL KEYJOINT125MM /3M LENG



2500510 METAL KEYJOINT250MM/3M LENG

HYDROTITEPremium grade, water swellable, waterstop range for use in cast in-situ concrete.

PART ID DESCRIPTION

2200560 HYDROTITE DSS0220 ADH BACK /LM

2200550 HYDROTITE CJ0725-3K ADH / LM

2200555 HYDROTITE CJ1020-2K ADH /LM

LEAKMASTERGun applied, water-swellable, waterstop paste

PART ID DESCRIPTION

2200785 LEAKMASTER / 320ML CARTRIDGE

SWELLABLE WATERSTOPHigh expansion butyl bentonite based hydrophilic waterstop for cast in-situ concrete

PART ID DESCRIPTION

2201110 SUPERSWELL 47B 25MM X 20MM

2500935 SUPERSWELL 19MMX12MMX12MM/M



DOWEL BARSRange of dowel bars in round and square, black and galvanised, priced per each, sold per each.

PART ID DESCRIPTION

2200845 RD DOWELS PLAIN 400MM X 16MM










2200871 RD DOWELS GAL 400MM X 16MM










2500667 SQ DOWELS PLAIN 400MM X 16MM



2500665 SQ DOWEL PLAIN 400MM X 20MM

2500675 SQ DOWEL PLAIN 500MM X 20MM





2200965 SQ DOWELS GAL 400MM X 16MM



2500670 SQ DOWEL GAL 400MM X 20MM

2500671 SQ DOWEL GAL 500MM X 20MM





CONSEAL 231Low expansion sealing gasket for joints in pre-cast concrete.

PART ID DESCRIPTION

2500240 CONSEAL231 19MMX12MMX12MM/M

2500245 CONSEAL 231 25MMX25MMX12MM/M

DOWEL CRADLESDowel cradle systems for concrete slabs and pavements. 3m lengths, sold per each, priced per each.

PART ID DESCRIPTION

2500700 CRADLE P6@450C125MM SLAB




2500701 CRADLE P6@450C125MM SLAB GAL




2501100 CRADLE P10@450C 175MM SLAB



2501115 CRADLE P10@450C 175MM SLAB GAL









TAPERED DOWEL CRADLESDowel cradle systems for concrete slabs and pavements. 3m lengths, sold per each, priced per each.

PART ID DESCRIPTION

2501152 TAPERED CRADLE P6 PD3@450C 125mm SLAB




2501162 TAPERED CRADLE P6 PD3@450C 125mm SLABGAL



2501170 TAPERED CRADLE P6 PD3@450C 200mm SLABGEL




2501180 TAPERED CRADLE P10 PD3@450C 150mmSLABGAL





JOINTFLEXFlexible, closed cell polyethylene joint filler, available in 25m rolls, plain, sold in rolls only, priced per each.

PART ID DESCRIPTION

2200680 JOINTFLEX 25M X 50MM X 10MM








2200651 JOINTFLEX 25M x 1M x 10MM

2200695 JOINTFLEX WHITE 25M X 75MM X 10MM

2200700 JOINTFLEX WHITE 25M X 100MM X 10MM

2200692 JOINTFLEX WHITE ADH 25M X 75MM X 10MM

2200694 JOINTFLEX WHITE ADH 25M X 100MM X 10MM

STIFFJOINTSemi-rigid, non-absorbent, closed cell polyethylene joint filler, 2.4m lengths, sold per each, priced per each.

PART ID DESCRIPTION

2201045 STIFFJOINT 2.4M X 50MM X 10MM








Semi-rigid, non-absorbent, closed cell polyethylene joint filler, 2.4m x 1m sheets, sold per each, priced per each.

PART ID DESCRIPTION

2201025 STIFFJOINT 2.4M X 1M X 7MM







Semi-rigid, non-absorbent, closed cell polyethylene joint filler, cut to size, cut up from sheets, sold per m2, priced per m2.

PART ID DESCRIPTION

SPSJ10 STIFFJOINT 10MM SPECIALS / M2






Semi-rigid, non-absorbent, closed cell polyethylene joint filler, sold in lengths only, priced per each.

PART ID DESCRIPTION




2500850 STIFFJOINT 1.4M X 100MM 10MM




ADHESIVE JOINTFLEXFlexible, closed cell polyethylene joint filler, available in 25m rolls, adhesive backed, sold in rolls only, priced per each.

PART ID DESCRIPTION

2200165 ADHES. JOINTFLEX 25MX50MMX10MM

2200195 ADHES.JOINTFLEX 25MX75MMX10MM





2200160 ADHES. JOINTFLEX 25MX250MMX10MM





POLYSTYRENELightweight, versatile material used for a wide variety of applications in the construction industry.

USES

Polystyrene is an economical, compressible filler.Available in sheets, blockouts and cylinders.

PART ID DESCRIPTION

2201090 POLYSTYRENE 2.4M X 1.2M X 10MM/EA




ECCOVOIDCollapsible void former

USES

To separate concrete slabs, ground beams and pile caps etc from unstable expansive soils that can exert significant swelling pressures on structural foundations.

PART ID DESCRIPTION

2501019 ECCOVOID VOIDFORMER 2.4MX.8MX40MM







EXPANDAFOAM BACKING RODMedium density, closed cell polyethylene backing rod range

USES

Expandafoam is a closed cell polyethylene foam rod supplied in circular section cords of varying diameters.

PART ID DESCRIPTION

665120 EXPANDAFOAM ROD 6MMX250M ROLL







665127 EXPANDAFOAM ROD 40MMX2M STRIP

665128 EXPANDAFOAM ROD 50MMX2M STRIP

EMER-SEAL BACKING RODEconomical, low density, open cell, polyurethane, sealant backing rod range

USES

Time saving – its flexibility, elasticity and round shape allows quick, efficient placement into both even and uneven joints. One size of diameter foam can be used in a range of joint sizes.Optimal sealant curing – open cell construction allows air to reach both sides of the sealant, ensuring uniform curing.

PART ID DESCRIPTION

665200 EMER-SEAL BACKING ROD 16MM X 150M ROLL

665201 EMER-SEAL BACKING ROD 22MMX100M ROLL





P R I M E R S

HILASTIC 44Flexible, one-component, acetoxy cure silicone sealant for glass, ceramics, aluminium.

USES

For sealing joints in glass and window construction, aquariums and display cases, general bonding, sealing and insulation.

PART ID DESCRIPTION

610302 HILASTIC 44 TRANS 300G (20/CTN)

HILASTIC 66Mould and fungus resistant, flexible, one-component silicone rubber sealant for bathrooms & kitchens.

USES

Hilastic 66 is a one-component, non-acid, gun applied silicone rubber sealant which cures rapidly to form a durable, watertight seal.

PART ID DESCRIPTION

610321 HILASTIC 66 WHITE 300G (20/CTN)

HILASTIC 88Neutral cure, one-component silicone sealant, for sheet metal lap joint, gutters, downpipes, etc

USES

Sealing joints in roof and wall sheets, guttering and downpipes, sheet metal water tanks, caravans, annexes and composite structures, suitable for use with laminated glass (nonstructural applications) and timber such as in window manufacture.

PART ID DESCRIPTION

610332 HILASTIC 88 TRANS 300G (20/CTN)

610333 HILASTIC 88 CONCRETE GREY 300G (20/CTN)

610334 HILASTIC 88 BLACK 300G (20/CTN)

PRIMER 4Used on non porous surfaces with Thioflex 600 GG & Thioflex 600 PG.

PART ID DESCRIPTION

665207 PRIMR NO.4 250ML

PRIMER 7Used on porous surfaces with Thioflex 600 PG / GG & Colpor 200 PF.

PART ID DESCRIPTION

665209 PRIMER NO.7 1L

PRIMER 9Used on plastics with Hilastic. Other sealants after testing.

PART ID DESCRIPTION

665212 PRIMER NO.9 250ML

PRIMER 11Used on non porous surfaces with Hilastic.

PART ID DESCRIPTION


PRIMER 132 part epoxy primer - Used on porous surfaces with NS 280, Emer-Seal 200; also Emer-Seal PU 40, Thioflex 600 (PG & GG) Emer-Seal CR when sealant in being immersed.

PART ID DESCRIPTION

665221 PRIMER NO.13 A-B/250ML

PRIMER 21Used on porous surfaces with Emer-Seal PU 25 & Emer-Seal PU 40 if required.

PART ID DESCRIPTION


PRIMER 10Used on porous surfaces with Hilastic.

PART ID DESCRIPTION

665214 PRIMER NO.10 250MLPRIMERS


S E A L A N T S

EMER-SEAL PU25High performance, flexible, one component, polyurethane joint sealant.

USES

Sealing joints in concrete panels, fibrous cement products, external cladding panels, blockwork and brickwork. Also in sealing joints around aluminium and timber door and window frames and between metal. Also suitable for sealing sawn joints up to 10 mm wide in concrete floors and pavements.

PART ID DESCRIPTION

620555 EMER-SEAL PU 25 BEIGE 600ML (20/CTN)

620545 EMER-SEAL PU 25 BLACK 600ML (20/CTN)

620525 EMER-SEAL PU 25 CONC.GREY 600ML (20/CTN)

620560 EMER-SEAL PU 25 DRIFTWOOD 600ML(20/CTN)

620535 EMER-SEAL PU 25 SANDSTONE 600ML (20/CTN)

620530 EMER-SEAL PU 25 WHITE 600ML (20/CTN)

EMER-SEAL MSOne part elastomeric high performance paintable sealant.

USES

Sealing joints in concrete panels, marble, granite blockwork and brickwork. And also for use in sealing joints around aluminium and timber door and window frames and between metal and some plastics.

PART ID DESCRIPTION

620515 EMER-SEAL MS GREY 600ML SAUSAGE

EMER-SEAL PU40Tough, abrasion resistant, one-component, polyurethane joint sealant, trafficable.

USES

For bonding or sealing joints between most construction materials, where a high bond strength is required.

PART ID DESCRIPTION

620601 EMER-SEAL PU 40 BLACK 600ML (20/CTN)

620600 EMER-SEAL PU 40 CONC.GREY 600ML (20/CTN)

620606 EMER-SEAL PU 40 CONCRETE GREY 200L

EMER-SEAL CRHighly chemical resistant, fast cure, durable, one component joint sealant.

USES

For sealing expansion and construction joints exposed to aggressive chemical environments.

PART ID DESCRIPTION

610501 EMER-SEAL CR CONCRETE GREY 600ML

EMER-SEAL ROADSEALHigh performance, low modulus, high joint movement accommodation, one component silicone rubber joint sealant.

USES

For sealing joints in concrete roads, runways, carparks and pavements.

PART ID DESCRIPTION

610402 EMER-SEAL ROADSEAL CONCRETE GREY 600ML

FLAMEX PUFire rated, high performance, flexible, one component, polyurethane sealant for external and internal applications.

USES

Flamex PU is designed for sealing exterior and interior movement joints where a fire rating of up to 4 hours is required.

PART ID DESCRIPTION

620035 FLAMEX PU CONCRETE GREY 600ML

EMER-SEAL CONSTRUCTION SILICONE HMTough, pick and abrasion resistant, one-component silicone sealant / adhesive for civil and industrial applications.

USES

For bonding or sealing joints between most construction materials, where a high bond strength is required.

PART ID DESCRIPTION

610375 EMER-SEAL CON SILICONE HM CON.GREY 600ML

NITOSEAL MB175 (FORMERLY PLASTISEAL)Rubberised bitumen, mastic joint sealant compatible with bitumen based membranes.

USES:

For sealing joints in retaining walls, roofing (sealing horizontal chases, flashings, gutterings and sheet laps), sealing terminations of bitumen based waterproofing membranes.

PART ID DESCRIPTION

600222 PLASTISEAL 600ML

EMER-SEAL CONSTRUCTION SILICONEHigh joint movement accommodation, one-component silicone joint sealant for facade applications.

USES:

For sealing moving or static joints in precast or in-situ concrete, curtain walls and lightweight cladding, tilt-up slabs, brick, blockwork, marble and granite facades, most building materials.

PART ID DESCRIPTION

630100 EMER-SEAL CONST SILICONE CON/GREY 600ML

630104 EMER-SEAL CONST SILICONE BLACK 600ML


FLOORING & SURFACE TREATMENTS


C U R I N G C O M P O U N D S

CONCURE A99Water based acrylic curing compound - conforms to AS3799

USES

Concure A99 is recommended for applications to the surfaces of freshly laid concrete, including renders, structural and mass concrete indoors and outdoors and particularly in situations where other conventional means of wet curing are difficult to maintain.

PART ID DESCRIPTION

900910 CONCURE A99 1000L

909900 CONCURE A99 205L

900909 CONCURE A99 20L

CURING COMPOUNDS

CONCURE X90Waterbased hydrocarbon resin curing compound - conforms to AS3799. Designed to degrade with UV exposure.

USES

Concure X90 is particularly suited to curing large areas of external concrete.

PART ID DESCRIPTION

900802 CONCURE X90 1000L

900801 CONCURE X90 205L

900804 CONCURE X90 20L

CONCURE B90Bitumen and hydrocarbon resin blend emulsified in water. Conforms to AS3799. Ideal primer coat for asphalt or bitumen overlays on concrete roads, bridges or parking decks.

USES

A blend of bitumen and hydrocarbon resins emulsified in water. The impervious film formed by Concure B90 prevents excessive water evaporation, promotes efficient cement hydration, minimises shrinkage whilst increasing durability of the concrete.

PART ID DESCRIPTION

900800 CONCURE B90 200L

900805 CONCURE B90 1000L

CONCURE WB30Water based wax emulsion, curing compound - conforms to AS3799

USES

This system ensures that the emulsion forms a non penetrating continuous film immediately upon contact with a cementitious surface. This impervious film prevents excessive water evaporation which in turn permits more efficient cement hydration thus reducing shrinkage and increasing durability.

PART ID DESCRIPTION

163052 CONCURE WB30 CLEAR 1000LT SHUTZ PACK

163055 CONCURE WB30 CLEAR 200L

163050 CONCURE WB30 CLEAR 20L

164075 CONCURE WB30 WHITE 1000L

164070 CONCURE WB30 WHITE 200L

900860 CONCURE WB30 WHITE BULK

INTEGRAL HARDENERSNITOFLOR SICALTOPFloor hardener, silicon carbide / alumina additive - dry shake on.

USES

Nitoflor Sicaltop provides a non-rusting, extremely hard wearing, abrasion and slip resistant surface to new concrete floors.

PART ID DESCRIPTION

402040 NITOFLOR SICALTOP GREY 20KG

NITOFLOR SICALTOP SPREADER

PART ID DESCRIPTION

BM-TV-830 SICALTOP COLOUR SPREADER


R E V E A L I N G A G E N T S / R E L E A S E A G E N T S

CONCURE AVEvaporative retarder for plastic concrete to reduce shrinkage cracks

USES

Concure AV is recommended for spray application onto the fresh surface of plastic concrete to greatly reduce cracking caused by unfavourable weather conditions.

PART ID DESCRIPTION

444445 CONCURE AV 200L

444444 CONCURE AV 20L

SURFACE REVEALING AGENTS

PRECO RWBSurface revealing liquid for exposed aggregate finish on fresh concrete

USES

Preco RWB is used to reveal aggregate in freshly placed horizontal concrete by delaying the surface set so that the mortar paste may be brushed and washed from between the aggregate particles, after the mass of the concrete has set.

PART ID DESCRIPTION

156080 PRECO RWB 20L

156085 PRECO RWB 200L

PRECO HPre-mixed surface revealing liquid for exposed aggregate finish on fresh horizontal concrete.

USES

Preco H is used to reveal aggregate in freshly placed horizontal concrete by delaying the surface set so that the mortar paste may be brushed and washed from between the aggregate particles, after the mass of the concrete has set. This produces an attractive exposed aggregate finish, or a key for subsequent pours or renders, e.g. floors, driveways, paving, etc.

PART ID DESCRIPTION

155550 PRECO H 205L

155500 PRECO H 20L

PRECO VPre-mixed surface revealing agent for use on vertical or horizontal formwork for exposed aggregate finishes.

USES

Preco V is used to reveal aggregate on vertical or horizontal surfaces of freshly placed concrete, by delaying the surface set so the mortar paste may be removed from between the aggregate particles. This product can be painted onto formwork to produce an exposed aggregate finish for ceilings, walls, pre-cast panels or to provide a mechanical key for subsequent renders, mortars, vertical construction joints, etc.

PART ID DESCRIPTION

155555 PRECO V 20L

FORM RELEASE AGENTEconomical, general purpose formwork and mould release agent

USES

To provide a positive form release and a smooth defect-free finish, suitable for steel, wood or paper forms.

PART ID DESCRIPTION

177000 FORM RELEASE AGENT 20L



RELEASE AGENTS

DURAFLOOR HDLiquid floor hardener / densifier / dustproofer - clear.

USES

On any new or existing internal concrete or masonry surface.

PART ID DESCRIPTION

505001 DURAFLOOR HD 20L



LIQUID HARDENERS

DURAFLOOR HD-SLiquid floor hardener / densifier / stain resistant / sheen sealer - clear.

USES

On any new or existing internal concrete or masonry surface.

PART ID DESCRIPTION

505003 DURAFLOOR HD-S 20L

505004 DURAFLOOR HD-S 5L


H A R D E N E R S & U N D E R L A Y S

DURAFLOOR LEVELTOPFloor underlay, self smoothing, levelling mortar for vinyl / carpet / timber (0 - 50 mm thickness).

USES

Durafloor Leveltop is designed as an internal high performance, easily installed underlay which forms a very smooth, hard surface for a variety of floor finishes including carpet, ceramic tiles, rubber, sheet vinyl and timber flooring.

PART ID DESCRIPTION

430092 DURAFLOOR LEVELTOP 15KG

CEMENTITIOUS & RESIN UNDERLAYS

CEMTOP GP ADVANCEDHigh performance floor underlay, self smoothing, levelling mortar for carpet / tiles (2-50 mm thickness) with enhanced flow properties for fast and easy application.

USES

Cemtop GP Advanced is designed as a heavy duty underlaywhich forms a smooth, hard surface for a variety of floorfinishes including carpet and ceramic tiles.

PART ID DESCRIPTION

430088 CEMTOP GP ADVANCED 18KG

NITOMORTAR 903Solvent free, general purpose, epoxy binder system.

USES

Nitomortar 903 can be combined with selected fillers and aggregates to produce epoxy mortars of various consistencies. Also used as a priming system with some Durafloor epoxy flooring products.

PART ID DESCRIPTION

481019 Nitomortar 903 Base Resin 20L

481040 Nitomortar 903 Base Resin 200L

481018 Nitomortar 903 Hardener 10L



DURAFLOOR LEVELBASEFloor underlay, economical sub-base build mortar (up to 200 mm thickness).

USES

Durafloor Levelbase is designed as a heavy duty sub-base underlay which forms a smooth, hard surface to be used under Durafloor Leveltop and Fosroc Cemtop GP Advanced & XD where deep sections are required.

PART ID DESCRIPTION

430095 DURAFLOOR LEVELBASE 20KG

DURAFLOOR LEVELTOP RAPIDFloor underlay, trowellable, rapid hardening, levelling mortar for carpet / tiles / vinyl (0-50 mm thickness).

USES

Durafloor Leveltop Rapid is designed as a heavy duty floor repair compound which provides a very smooth surface allowing the smooth installation of carpet, ceramic tiles sheet rubber, sheet vinyl and vinyl tiles.

PART ID DESCRIPTION

430105 DURAFLOOR LEVELTOP RAPID 20KG

DURAFLOOR LEVEL PRIMEHigh performance primer for Cemtop XD, Cemtop GP Advanced, Durafloor Leveltop, Durafloor Leveltop Rapid and Durafloor Levelbase.

USES

Concentrated high performance primer for cementitious underlays.

PART ID DESCRIPTION

480005 DURAFLOOR LEVEL PRIME 1L



PRIMERS


U N D E R L A Y S & T O P P I N G S

DURAFLOOR TFFloor topping, trowel applied, high build epoxy resin system (5 mm thickness).

PART ID DESCRIPTION

405345 Durafloor TF Base Resin15L

405350 Durafloor TF Hardener 5L

405355 Durafloor TF Fillers 20kg

CEMTOP XDCementitious floor topping internal trafficable wear surface (6-12 mm thickness).

PART ID DESCRIPTION

402055 Cemtop XD 15kg

DURAFLOOR V ANTI-SKIDHeavy duty, flow applied, lightweight anti-skid surface dressing.

PART ID DESCRIPTION

400400 Durafloor V Anti-Skid Base 16L Pack

400405 Durafloor V Anti-Skid Hardener 16L Pack

400410 Durafloor V Anti-Skid Fillers 16L Pack

405760 Durafloor Heavy Duty Aggregate 25kg

DURAFLOOR SLFloor topping, industrial, self smoothing epoxy resin system (2-4 mm thickness).

USES

Durafloor SL provides a dense, impervious, coloured and chemically resistant floor surface which is hygienic and easy to clean.

PART ID DESCRIPTION

405400 Durafloor SL Base Resin 16L Pack

405800 Durafloor SL Base Resin 200L

405700 Durafloor SL Hardener 16L Pack

405805 Durafloor SL Hardener 200L

404045 Durafloor SL Fillers 10kg


FLOOR TOPPINGS

DURAFLOOR SLXFloor topping, industrial, self smoothing epoxy resin system for cold weather application (2-4 mm thickness).

PART ID DESCRIPTION

405900 Durafloor SLX Base Resin 16L Pack

402000 Durafloor SLX Base Resin 200L

405910 Durafloor SLX Hardener 16L Pack

402005 Durafloor SLX Hardener 200L



AEGIS MSPCementitious floor topping internal / external trafficable waterproofing surface (2-4 mm thickness).

USES

Aegis MSP is used to provide a strong and durable cementitious coating that can be applied to a wide variety of substrates, including concrete, concrete blocks, polystyrene blocks, aerated concrete blocks (AAC), asphalt and fibre cement.

PART ID DESCRIPTION

752003 Aegis MSP Coarse Grey 20kg

752001 Aegis MSP Fine Grey 20kg

750007 Aegis Surface Primer #1 20L

DURAFLOOR XDurafloor X produces a topping and coating system with a textured finish, which provides a hard-wearing, chemically resistant floor that can handle extreme temperatures. The system also has anti-microbial properties which reduce the growth of bacteria and mould.

USES

Durafloor X has been designed to produce a flooring system for applications that require high resistance to mechanical stress and chemical attack, that are subject to extreme temperatures and need to be applied within a limited timeframe. Typical uses for the system are in wet processing zones in chemical processing plants and food preparation and manufacturing areas.

PART ID DESCRIPTION

405854 DURAFLOOR X COAT PART A - 4.83KG KIT

405855 DURAFLOOR X COAT PART B - 4.83KG KIT

405856 DURAFLOOR X COAT PART C - 4.83KG KIT

405848 DURAFLOOR X PRIMER BASE 10KG KIT

405849 DURAFLOOR X PRIMER HARDENER 10KG KIT

405850 DURAFLOOR XT BASE

405851 DURAFLOOR XT HARDENER

405852 DURAFLOOR XT FILLER 2

405853 DURAFLOOR XT FILLER 1

DURAFLOOR N (NOVOLAC)HIghly chemically resistant Novolac epoxy clear binder produces various coating and topping application systems.

USES

Durafloor N is an all purpose, highly chemically resistant Novolac epoxy coating/topping system suitable for a number of surfaces including concrete, steel and masonry.

PART ID DESCRIPTION

401040 Durafloor N (Novolac) Base 15L

401045 Durafloor N (Novolac) Hardener 10L


T O P P I N G S & C O A T I N G S

DURAFLOOR HPFloor coating, high performance epoxy, solvent free, non-tainting.

USES

Durafloor HP is a heavy duty, industrial/commercial coating for concrete floors and walls that is attractive and easily cleaned. Highly resistant to chemical attack and the action of forklift vehicular and commercial type traffic.

PART ID DESCRIPTION

414501 Durafloor HP Base Resin 8L Pack

414210 Durafloor HP Special Colour Base Resin 8L Pack

414414 Durafloor HP Special Colour Base Resin 16L Pack

414502 Durafloor HP Hardener 8L Pack

414415 Durafloor HP Hardener 16L Pack

414505 Durafloor HP 4L Pack

414507 Durafloor HP Special Colour 4L

COATINGS

DURAFLOOR HSFloor coating, economical, high build epoxy, 90% solids

USES

Durafloor HS is a heavy duty, commercial abrasion resistant treatment for concrete floors that is attractive and easily cleaned. Highly resistant to chemical attack and the action of commercial type traffic.Suitable for use in wet areas where strict levels of hygiene and cleanliness are required or where chemicals are manufactured, spilled or are an integral part of the process.

PART ID DESCRIPTION

414600 Durafloor HS Base 8L Pack

414649 Durafloor HS Hardener 8L Pack

DURAFLOOR FCFloor/wall coating, solvent free epoxy, fast cure.

USES

A heavy duty, 100% solids, non-skid surface coating for concrete and steel floors that is attractive and easily cleaned. Highly resistant to chemical attack and the action of vehicular and foot traffic.

PART ID DESCRIPTION

414504 Durafloor FC 4L Pack

NITOFLOR FC100Floor sealer, general purpose solvent based, UV stable, acrylic coating.

USES

Nitoflor can be used as a sealer for concrete floors to provide a dustproof and more easily cleaned surface with resistance to penetration of oils and other liquids. Ideal for warehouses, car parks, light industrial buildings, etc.

PART ID DESCRIPTION

410002 Nitoflor FC100 Clear 20L

410001 Nitoflor FC100 Clear 200L

411022 Nitoflor FC100 Special Colour 20L

561574 Nitoflor FC100 T&G Grey 20L

561572 Nitoflor FC100 T&G Grey 200L

NITOFLOR FC120 HBColoured floor coating, chlorinated rubber, UV stable, for trafficable floors and carparks.

USES

Nitoflor FC120 is suitable for use in heavy traffic areas such as light industrial traffic, stairs, fuel station forecourts, driveways and parking stations.

PART ID DESCRIPTION

411050 Nitroflor FC120 HB Black 20L

411070 Nitroflor FC120 HB Silver Grey 20L

NITOFLOR FC130Floor/wall coating, economical, water based epoxy, chemical resistant.

USES

Nitoflor FC130 is used to provide a dust-proof, easily cleaned surface which is resistant to most oils and liquids. It is suitable for use on walls and floors in warehouses, garages, light industrial and food processing areas, kitchens and other areas of pedestrian and light vehicular traffic.

PART ID DESCRIPTION

412184 Nitoflor FC130 Base For Colour Packs 3L

412182 Nitoflor FC130 Clear Base 2.9L

412181 Nitoflor FC130 Clear Hardener 13.1L

412196 Nitoflor FC130 Mid Grey Hardener 13L

412183 Nitoflor FC130 Silver Grey Hardener 13L

412215 Nitoflor FC130 Silver Trophy Hardener 13L

412210 Nitoflor FC130 Special Colour Hardener 13L

412180 Nitoflor FC130 Silver Grey 4L Pack


C O A T I N G S / D E C O R A T I V E F L O O R T O P P I N G S

DURAFLOOR PUSingle pack, high build, clear high gloss, high abrasion resistant polyurethane coating.

USES

Durafloor PU is a high build coating, formulated for both interior and exterior applications to provide a clear, high gloss, high abrasion resistant finish.

PART ID DESCRIPTION

400650 DURAFLOOR PU 5L

400655 DURAFLOOR PU 20L

DURAFLOOR SRModified synthetic rubber based flooring coating.

USES

Specifically formulated to provide quick drying, hardwearing, trafficable surfaces for floors including workshops,storerooms, undercover parking areas et

PART ID DESCRIPTION

561310 DURAFLOOR SR 4L

561311 DURAFLOOR SR 20L

TOPPINGS & COATINGS COLOUR PACKSDURAFLOOR COLOUR PAKSAvailable in Durafloor SL, TF, HS, HP, FC & N

See Durafloor Colour Chart for colours.

PART ID DESCRIPTION

440001 DURAFLOOR COL PAK BANKSIA 0.5KG

440010 DURAFLOOR COL PAK CREAM 0.5KG

440013 DURAFLOOR COL PAK FERN GREEN 0.5KG

440003 DURAFLOOR COLOUR PAK BLACK 0.5KG

440018 DURAFLOOR COLOUR PAK HARBOUR BLUE 0.5KG

440042 DURAFLOOR COLOUR PAK KOALA GREY 0.5KG

440075 DURAFLOOR COLOUR PAK LIGHT GREY BLUE 0.5KG

444000 DURAFLOOR COLOUR PAK OFF WHITE 0.5KG

440026 DURAFLOOR COLOUR PAK PASTEL GREY 0.5KG

440029 DURAFLOOR COLOUR PAK RASPBERRY 0.5KG

440070 DURAFLOOR COLOUR PAK SAFETY YELLOW 0.5KG

440031 DURAFLOOR COLOUR PAK SAND 0.5KG

440017 DURAFLOOR COLOUR PAK SILVER GREY 0.5KG

440059 DURAFLOOR COLOUR PAK WOOLWORTHS RED 0.5KG

440061 DURAFLOOR COLOUR PAK WOOLWORTHS GREY 0.5KG


D E C O R A T I V E F L O O R T O P P I N G S & C O N C R E T E S E A L E R S

MASTERSHIELD M90Premium Epoxy Commercial Flooring Product.

USES

Premium Polymer flooring product. May be tinted, flaked and other decorative inclusions. Clear product that may be used to suspend objects, graphics or lighting for a novelty feature floor. Chemical resistant - ideal for commercial and industrial floors. FOR INSIDE USE - Special application for outside use.

PART ID DESCRIPTION

MS90A Mastershield - M90 - 6L - Part A

MS90B Mastershield - M90 - 4L - Part B

MS90C Mastershield - M90 - 2L - Part C - Fast Cure Hardener NLA

MS905KIT Mastershield - M90 - 5L Kit

MS90MVA Mastershield - M90 - MV Part A

MASTERSHIELD UA20High Solids, Gloss Urethane Sealer

USES

Used as a high gloss finish and advanced protection over Mastershield polymer flooring, Covacrete, Stampcrete, Stencilcrete and other concrete and masonry surfaces. Also ideal over polished concrete. Exceptional performance for economy.

PART ID DESCRIPTION

UA20A UA20 Urethane Acrylic - 8.7Lt Part A

UA20B UA20 Urethane Acrylic - 1.25Lt Part B

AQUEOUS TINTSColour liquid dispersion of organic and inorganic pigments

USES

For colouring Mastershield M50, Covacrete Base Powder.

PART ID DESCRIPTION

MTBIS Mastershield - Aqueous Tint - Biscuit

MTBON Mastershield - Aqueous Tint - Bone

MTCLA Mastershield - Aqueous Tint - Clay

MTMUS Mastershield - Aqueous Tint - Musk

MTOUT Mastershield - Aqueous Tint - Outback

MTSIL Mastershield - Aqueous Tint - Silver Grey

MTTAN Mastershield - Aqueous Tint - Tan

MTBRWHT Mastershield - Aqueous Tint - White

MTBRBL Mastershield - Aqueous Tint - Black

MTBRTY Mastershield - Aqueous Tint - Bright Yellow

MTBRTR Mastershield - Aqueous Tint - Bright Red

MTBRTG Mastershield - Aqueous Tint - Bright Green

MTBRTB Mastershield - Aqueous Tint - Bright Blue

MASTERSHIELD FLAKEDecorative flooring polymer flake.

USES

Mastershield Polymer Flake is used in decorative Polymer Flooring.

PART ID DESCRIPTION

PFFLA Mastershield Flake - Flake Various NSI

WATERBASED ACRYLIC SEALERThe Green Choice for the environmentally smart consumer. Low odour and ideal for confined spaces or indoor applications.

� Low odour - very low VOC � Good marking resistance � Medium gloss � Self-crosslinking polymer � Water clean up � Tintable

PART ID DESCRIPTION

WBS20 LUSTRESEAL WATERBASED ACRYLIC SEALER 20L

INTERNAL CONCRETE SEALERS

LUSTRESEAL M20Premium Polyurethane, High Solids Sealer.

USES

The toughest sealer in the Lustreseal range - very high gloss and extremely hard. Suitable over Mastershield polymer flooring, Covacrete and other concrete (incl. Stamp/Stencil) and masonry surfaces in thoroughly dry conditions. Also ideal over polished concrete. M20 is a moisture curing single pack polyurethane.

PART ID DESCRIPTION

UA20A UA20 Urethane Acrylic - 8.7Lt Part A

UA20B UA20 Urethane Acrylic - 1.25Lt Part B

DECORATIVE FLOOR TOPPINGS

MASTERSHIELD M50Economical Epoxy Flooring or Surface Primer.

USES

A two pack Aqueous Epoxy that can be used as a primer or as a base for epoxy flooring. May be tinted (aqueous tints), flaked or sprayed in contrasting flecks. Provides a low gloss, satin finish. Highly economical epoxy flooring. FOR INSIDE USE - Special application for outside use.

PART ID DESCRIPTION

MS50A Mastershield - M50 - 5L - Part A - Opaque Base NSI

MS50NTA Mastershield - M50 - 5L - Part A - Neutral Base NSI NLA

MS50B Mastershield - M50 - 5L - Part B - For Opaque and Neutral Bases NSI


C O N C R E T E S E A L E R S

LUSTRESEAL COLOUR TINTColour liquid dispersion of organic and inorganic pigments.

USES

Lustreseal Colour Tint is added to Lustreseal Acrylic Sealerto give various shades of colour to stamped, stencilled orplain concrete. Can also be used to tint Mastershield M90.

PART ID DESCRIPTION

LSAPR LUSTRESEAL TINT APRICOT 1LTR

LSBAR LUSTRESEAL TINT BARLEY 1LTR

LSBEI LUSTRESEAL TINT BEIGE 1LTR

LSBLA LUSTRESEAL TINT BLACK 1LTR

LSBLU LUSTRESEAL TINT BLUESTONE 1LTR

LSBRI LUSTRESEAL TINT BRICK RED 1LTR

LSBRO LUSTRESEAL TINT BRONZE 1LTR

LSBUR LUSTRESEAL TINT BURGUNDY 1LTR

LSCHA LUSTRESEAL TINT CHARCOAL 1LTR

LSCIN LUSTRESEAL TINT CINNAMON 1LTR

LSCOF LUSTRESEAL TINT COFFEE BROWN 1LTR

LSCRE LUSTRESEAL TINT CREAM 1LTR

LSGRY LUSTRESEAL TINT GREY 1LTR

LSGUM LUSTRESEAL TINT BLUE GUM 1LTR

LSLIG LUSTRESEAL TINT LIGHT TERRACOTTA 1LTR

LSMAR LUSTRESEAL TINT MARIGOLD 1LTR

LSNUT LUSTRESEAL TINT NUTMEG 1LTR

LSROS LUSTRESEAL TINT BLUSHING ROSE 1LTR

LSSAH LUSTRESEAL TINT SAHARA SAND 1LTR

LSSAN LUSTRESEAL TINT SAND 1LTR

LSTER LUSTRESEAL TINT TERRACOTTA 1LTR

LSVIN LUSTRESEAL TINT VINTAGE BUFF 1LTR

LSWHI LUSTRESEAL TINT WHITE 1LTR

ACRYLIC SEALERStandard sealer used for stencil & stamped surfaces. Good all-round concrete sealer.

� Durable � Easy to apply & maintain � Semi gloss finish � High clarity � Tintable

USES

Used as a high quality, gloss protective finish over decorative and other concrete and masonry surfaces. For best results, first prime with Lustreseal Superbond.

PART ID DESCRIPTION

ACR5 SEALER ACRYLIC 5 LT

ACR20 SEALER ACRYLIC 20LT

ACR200 SEALER ACRYLIC 200LT

EXTERNAL CONCRETE SEALERS EXTENDED WEAR PLUSHard wearing, high gloss sealer.

� High durability � Excellent fuel, oil, mould & fungi resistance � Semi gloss - high clarity � Excellent marking resistance

USES

Used for extended longevity in place of Acrylic Sealer for most concrete and masonry surfaces. Provides superior protection from the ingression of dirt, mould, fungi, fuel and oil. High quality wet-look finish. For best results, first prime with Lustreseal Superbond.

PART ID DESCRIPTION

EXT20 SEALER EXTENDED WEAR PLUS 20LT

EXT200 SEALER EXTENDED WEAR PLUS 200LT

SOLVENT

PART ID DESCRIPTION

SOL10 SOLVENT 10 L

SOL20 SOLVENT 20 L

SOL4 SOLVENT 4 L

SUPERBONDSame day prime sealer.

� Excellent moisture tolerance � Priming sealer � High penetration & adhesion � Flexible � Ideal for use as resealing primer � Great for sealing exposed aggregate

USES

Use as same day sealer/primer for concrete and primer for masonry and natural stone surfaces (for porous stone - test before use). Also suitable for resealng - provides essential flexibility between finish coats (See Reseal Guide). Must be over-coated with a finish sealer upon surface curing (with the exception of exposed aggregate).

PART ID DESCRIPTION

SUP20 SEALER SUPERBOND 20LT

SUP200 SEALER SUPERBOND 200LT

MATT FINISH SEALERWhen a natural look is more appealing than a gloss.

� Natural low lustre � Good marking resistance � Hard wearing � Stylish alternative � Tintable

USES

Used as a natural low sheen finish coat for most decorative concrete or masonry surfaces. Popular as an alternative finish for internal floors and also as a natural look finish for resurfaced concrete, stamped impression concrete and stencil concrete. Low lustre masks minor marking and scuffing. For best results, first prime with Lustreseal Superbond. (Not to be used as a first coat primer).

PART ID DESCRIPTION

ACRM20 SEALER MATT FINISH 20LT


WATERPROOFING


P R I M E R S

EMER-ACRYLIC SEALEREconomical, water based concentrate and masonry primer.

USES

Emer-Acrylic Sealer can be used as a primer/sealer coating on concrete, brick, tilt-up panels etc. Provides an even non absorbent substrate over which Emer-impact, Emer-Clad membrane systems and Emer-Acrylic Low Sheen can be applied.

PART ID DESCRIPTION

561452 EMER-ACRYLIC SEALER 4L

561785 EMER-ACRYLIC SEALER 15L

EMER-COAT CLEAR SEALERPenetrating, solvent based, clear masonry and concrete binder/sealer.

USES

As a primer, sealer coating on fibre cement, masonry, blockwork, brick or other masonry surfaces. Provides an excellent seal over aged, weathered paintwork and will penetrate powdery coatings such as “kalsomine” and “distemper”.

PART ID DESCRIPTION

561018 EMER-COAT CLEAR SEALER 4L

561019 EMER-COAT CLEAR SEALER 20L

EMER-BONDWaterborne, anti-corrosive primer.

USES

For fabrication and maintenance work generally. Suitable as a shop primer due to its quick drying, outstanding adhesion, good resistance to corrosion and the absence of health and fire hazards. For application in special conditions, consult Parchem for detailed information.

PART ID DESCRIPTION

561616 EMER-BOND PRIMER 4L

561790 EMER-BOND PRIMER 15L

EMER-TANTannin phosphate, rust-converter for corroding metal, pre-painting treatment.

USES

The versatility of Emer-Tan application makes it suitable for small or large surfaces, inaccessible areas or wherever rust is present. As a surface pre-treatment for rusted structural steel, machinery, gates, railings, marine fittings, motor vehicle floors and all rusted surfaces where the complete removal of rust is not feasible or economical.

PART ID DESCRIPTION

561610 EMER-TAN 5L

EMER-GARD PRIMER TYPE 2Quick drying anti-corrosive primer .

USES

Emer-Gard Primer Type 2 can be used for all new or old steel surfaces in industrial, commercial or domestic situations. Used where high durability is desired when only a minimum of surface preparation is possible, for practical, safety or reasons of economy.

PART ID DESCRIPTION

561176 EMER-GUARD PRIMER TYPE 2 4L

EMER-ACRYLIC LOW SHEENA High quality, water based acrylic, low sheen coating.

USES

Suitable for application to brickwork, cement render, concrete, blockwork, fibre cement sheeting, plaster board and pre-primed metals. As a general purpose, high opacity, durable protective, decorative coating mainly for exterior use, but also suited for interior surfaces.

PART ID DESCRIPTION

561394 EMER-ACRYLIC LOW SHEEN TINTS 15L


P R I M E R S / L I Q U I D A P P L I E D M E M B R A N E S

LIQUID APPLIED MEMBRANES

EMER-CLAD WATERPROOFINGAcrylic, flexible waterproofing membrane, for internal and UV exposed external areas - colour range available.

USES

Emer-Clad is suitable for application to many common substrates including concrete, fibrous cement products, metals, timber with priming required on most substrates.

PART ID DESCRIPTION

740040 EMER-CLAD MATT LIGHT GREY 4L


561724 EMER-CLAD MATT MID GREY 15L

561720 EMER-CLAD MATT WHITE 15L

561770 EMER-CLAD MATT A BASE 15L

561765 EMER-CLAD MATT B BASE 15L

561760 EMER-CLAD MATT C BASE 15L



561755 EMER-CLAD SATIN A BASE 15L

561750 EMER-CLAD SATIN B BASE 15L

561745 EMER-CLAD SATIN C BASE 15L

740205 EMER-CLAD SATIN WHITE 4L


740220 EMER-CLAD SATIN LIGHT GREY 4L


740225 EMER-CLAD SATIN MID GREY 4L




EMER-CLAD FIRECHECKFire retardant protective coating for concrete and masonry surface.

USES

On timber and all types of building boards, ceiling tiles, panelling etc. Over polyurethane and styrene foam insulation, pipe lagging or similar it provides a fire retardant, abrasion resistant, flexible skin that also withstands weather and wear.

PART ID DESCRIPTION

561005 EMER-CLAD FIRECHECK WHITE 15L

EMER-CLAD ARCHITECTURALDecorative and protective façade coating, water based acrylic, highly durable, elastomeric, waterproofing membrane with full colour range.

USES

Emer-Clad is suitable for application to many common substrates including concrete, render, masonry, fibrous cement products, metals, timber and bituminous membranes. Some special priming may be required.

PART ID DESCRIPTION





561770 EMER-CLAD MATT A BASE 15L

561765 EMER-CLAD MATT B BASE 15L

561760 EMER-CLAD MATT C BASE 15L

561719 EMER-CLAD MATT TINTS 15L



561755 EMER-CLAD SATIN A BASE 15L

561750 EMER-CLAD SATIN B BASE 15L

561745 EMER-CLAD SATIN C BASE 15L

561388 EMER-CLAD SATIN TINTS 15L








L I Q U I D A P P L I E D M E M B R A N E S

EMER-PROOF MULTIPURPOSE PRIMER & WP ADDITIVESBR latex primer & waterproofing additive.

USES

Emer-Proof Multipurpose Primer & WP Additive is a single component SBR primer that provides excellent high bonding and penetrating properties into porous concrete and masonry surfaces.Can also be used as a waterproofing additive into cement based compounds for enhanced adhesion and waterproof properties

PART ID DESCRIPTION

743120 EMER-PROOF MULTI PURP PRIMER/WP ADD 15L

743121 EMER-PROOF MULTI PURP PRIMER/WP ADD 4L

EMER-PROOF NON-POROUS PRIMERWater-based solvent free primer for non-porous substrates

USES

Emer-Proof Non-Porous Primer is specifically designed with adhesion enhancing properties over metallic, smooth, dense, and non-porous surfaces. Providing a safe alternative to hazardous solvent based primers and etching products, Emer-Proof Non-Porous Primer enables the adhesion of Emer-Proof membranes and adhesives over non-absorbent surfaces.

PART ID DESCRIPTION

743123 EMER-PROOF NON POROUS PRIMER 4L

743124 EMER-PROOF NON POROUS PRIMER 1L

EMER-PROOF AQUA BARRIERWater borne epoxy membrane / barrier for porous surfaces.

USES

Emer-Proof Aqua Barrier is a grey, two-component, matt to semi-gloss epoxy coating. When applied at 200 microns dry film thickness will provide a tenaciously bonded coating controlling the transmission of liquid moisture.

PART ID DESCRIPTION

405016 EMER-PROOF AQUA-BARRIER GREY 20L KIT PART A

405017 EMER-PROOF AQUA-BARRIER GREY 20L KIT PART B

EMER-PROOF ECOFLEXHigh performance water based rubberised bitumen waterproofing membrane.

USES

Emer-Proof Ecoflex is a flexible, solvent free polymer modified bitumen membrane, designed for a wide range of waterproofing applications over numerous building substrates.

PART ID DESCRIPTION

730730 EMER-PROOF ECOFLEX 20L

EMER-PROOF ECOFLEX ANTI ROOTPolymer modified bitumen liquid membrane with plant root inhibitors.

USES

Emer-Proof Ecoflex Anti-Root is a flexible, solvent free polymer modified bitumen membrane with root inhibiting properties designed for subterranean applications.

PART ID DESCRIPTION

743100 EMER-PROOF ECOFLEX ANTI ROOT 15L


L I Q U I D A P P L I E D M E M B R A N E S

EMER-PROOF QUICK DRY TWO PARTPolymer / cementitious two part waterproofing membrane.

USES

Emer-Proof Quick Dry Two Part is a water based, fast drying, flexible 2 component, polymer modified cement based waterproofing membrane.

PART ID DESCRIPTION

743110 EMER-PROOF QUICK DRY PT A (LIQ) 20L KIT

743115 EMER-PROOF QUICK DRY PT B (POW) 20L KIT

EMER-PROOF UNDER TILEFibre enhanced single component water based SBR hybrid polyurethane membrane.

USES

Emer-Proof Under Tile is a flexible, fibre reinforced, high bonding, SBR modified elastomeric membrane designed for internal wet areas to be overlaid directly with tiles or toppings.

PART ID DESCRIPTION

743116 EMER-PROOF UNDER TILE 15L

EMER-PROOF TOP COATWater based acrylic hybrid membrane top coat for UV exposed applications.

USES

Emer-Proof Top Coat is a hard wearing membrane designed for external applications on horizontal surfaces. Suitable for use as a trafficable top coat over Emer-Proof Quick Dry Two Part or Emer-Proof EcoSeal for roofs and deck areas. Emer-Proof Top Coat exhibits outstanding adhesion properties and excellent UV weather resistance.

PART ID DESCRIPTION

743118 EMER-PROOF TOP COAT 15L

EMER-PROOF EXTENDED WEAR CLEAR COATSolvent free aliphatic polyurethane clear sealer.

USES

Emer-Proof Extended Wear Clear Coat is a solvent free aliphatic polyurethane sealer designed for use over concrete, masonry and mineral surfaces. Suitable for a variety of exterior applications, exhibiting excellent UV resistance and durability. Compatible over a range of porous finish surfaces such as textured coatings, exposed membrane surfaces and cement based coatings. Offers ideal finish over Emer-Proof Top Coat.

PART ID DESCRIPTION

743119 EMER-PROOF EXTENDED WEAR CLEAR COAT 15L

EMER-PROOF ECOSEALNext generation solvent free polyurethane membrane.

USES

Emer-Proof EcoSeal is a new generation, solvent free one component polyurethane membrane. User and environmentally friendly alternative to solvent based polyurethanes for use in areas exposed to permanently wet conditions. Suitable for internal and external wet areas allowing the direct fix of tiles and toppings without bonding issues commonly associated with solvent based and moisture cured polyurethane products.

PART ID DESCRIPTION

743117 EMER-PROOF ECOSEAL 15L


S E L F A D H E S I V E M E M B R A N E S

EMER-PROOF EJB TAPESuperior sealing system for critical areas over traditional bondbreaking sealants and tapes.

USES

Emer-Proof EJB Tape has been developed as a superior alternative to traditional bond breaking methods for sealing critical movement zones. Emer-Proof EJB Tape is suitable for internal, external underground and fully immersed applications.

PART ID DESCRIPTION

743265 EMER-PROOF EJB TAPE

743270 EMER-PROOF EJB TAPE INTERNAL CORNERS

743275 EMER-PROOF EJB TAPE EXTERNAL CORNERS

POLYFAB LD 7230W

PART ID DESCRIPTION

771193 POLYFAB LD 7230W 1.27X1M

SONTARA TAPENon woven reinforcement fabric.

USES

Sontara Reinforcement Fabric is a non woven fabric designed for use with liquid membrane and high build coating products for enhancing reinforcement, tensile strength and uniform layers in liquid membrane applications.

PART ID DESCRIPTION

771086 SONTARA TAPE 100MMX100M ROLL

771087 SONTARA TAPE 150MM X 100M ROLL



771090 SONTARA TAPE 1M X 100M ROLL

EMER-PROOF HDPESelf adhesive bituminous membrane incorporating a cross laminated HDPE film that provides the product excellent physical & application properties.

USES

Emer-Proof HDPE is used to waterproof foundations, basements, roofs, retaining walls and tunnels, box culverts and planter boxes.

PART ID DESCRIPTION

742034 1M X 20M ROLL

EMER-PROOF HDSelf adhesive bituminous membrane incorporating a polypropylene mesh for added strength and heat stability.

USES

Emer-Proof HD is used to waterproof bridge decks, ramps, car parks, and road pavements where the membrane will be overlaid with hot asphalt.

PART ID DESCRIPTION

742038 1M X 20M ROLL

TILEBOND FLEXRubber modified, flexible, off-white, cement based, ceramic tile adhesive for use with Emer-Proof 680.

USES

Tilebond Flex can be used both internal / external on walls and floors. It can be used to bond a variety of different tiles to a variety of different substrates. It is fast setting, meaning you can commence grouting 6-8 hours @ 20OC after completion of tiling.

PART ID DESCRIPTION

307001 EMER-PROOF TILEBOND FLEX 20KG

TILE ADHESIVE

EMER-PROOF SELF ADHESIVE PRIMERHigh tack primer for Emer-Proof HDPE/HD and for Index Autotene Base P / Index Autotene Asfaltico.

PART ID DESCRIPTION

742041 EMER-PROOF SELF ADHESIVE PRIMER 20L

LIQUID APPLIED ACCESSORIES

SELF ADHESIVE MEMBRANES


P R E - A P P L I E D M E M B R A N E S / D R A I N A G E & P R O T E C T I O N

PROOFEX ENGAGEPre-applied waterproofing membrane which mechanically bonds to poured concrete.

USES

Proofex Engage is a unique patented waterproofing membrane for a range of waterproofing applications including basements and substructures. It provides water vapour and gas protection to water excluding structures and protects concrete from aggressive ground salts and chemicals.

PART ID DESCRIPTION

707070 1.27 X 30M ROLL

PROOFEX DETAILS

PART ID DESCRIPTION

707071 PROOFEX DETAIL STRIP 10M

707072 PROOFEX EXT CORNER (200X200X200MM)

707073 PROOFEX INT CORNER (200X200X200MM)

707075 PROOFEX LM 28KG

707077 PROOFEX L SECTION 10M

707078 PROOFEX TOP HAT 110mm

707079 PROOFEX TOP HAT 160mm

707085 FOSROC POLYUREA WCS GUN GRADE

707086 FOSROC POLYUREA WCS - STATIC MIXING NOZZLES

707087 FOSROC POLYUREA WCS - MANUAL GUN

PRE-APPLIED MEMBRANE & ACCESSORIES

IMPRABOARDPolyethylene coreflute board for low duty membrane protection.

PART ID DESCRIPTION

771079 IMPRABOARD 1830 X 1220

EMER-PROOF DRAIN VDimpled protection and drainage membrane in high-density extruded polyethylene with continuous filament yarn.

USES

Emer-Proof Drain V is ideal for the protection of foundations and is perfect for “dry” roof gardens, as it replaces the traditional aggregate draining layer and speeds up the work, making it less expensive and reducing both the weight and thickness of the roof garden.

PART ID DESCRIPTION

743072 EMER-PROOF DRAIN V 2M X 20M ROLL

USES

Consisting of 100% synthetic fibres, mainly polyester, resin free and glue free, Emer-Proof Geotex represents the best solution when building tunnels, waste dumps, water basins, river banks and reinforced soil.

PART ID DESCRIPTION

744000 EMER-PROOF GEOTEX 300 1M WIDE

DRAINAGE & PROTECTION

PLASTICPART ID DESCRIPTION

GD-FILM Black IR2 4m x 50m roll 200Um

GD-FILMO450200 Orange IR3 4m x 50m roll 200Um

GD-FILMO633200 Orange IR3 6m x 33m roll 200Um

Note: 2m wide rolls

EMER-PROOF GEOTEX

Non-woven fabric in needle-punched polyester for the drainage of construction works


T O R C H A P P L I E D M E M B R A N E S

TORCH APPLIED MEMBRANES

INDEX ROLLBASEPolyester fabric backed base sheet, for heat sensitive substrates, in multi-layer torch-on membrane systems.

USES

Rollbase is particularly suited as a base sheet for heat sensitive substrates in multi-layer torch applied bitumenLose laid, mechanically fastened, fully or part adhered with Adhesive A901 (general purpose contact adhesive), hot asphalt roll & pour method membrane systems.

PART ID DESCRIPTION

742010 1M X 10M ROLL

INDEX VAPORDIFFUSERElastoplastomeric membrane with deep bitumen underside rivets, to allow water vapour to diffuse and provided waterproofing in the base layer in multi-layer systems.

USES

Vapordiffuser is used for both new construction and renovation work, on damp surfaces where blisters can form in the waterproof layer. It can be installed as a visible layer directly on concrete or to renovate an old bituminous layer which is no longer waterproof.

PART ID DESCRIPTION

742030 1M X 7.5M ROLL

INDEX FIDIA3 mm thick elastomeric, torch applied, reinforced with rot-proof non-woven polyester stabilised with glass matt, membrane. Used for single or multi layer systems.

USES

Fidia polyester is used as a continuous waterproofing membrane for foundations, basements, tunnels, roofs etc.

PART ID DESCRIPTION

742000 3MM 1M X 10M ROLL

INDEX MODO/P3.5 mm thick, elastoplastomeric, torch-applied, reinforced with polyester and stabilised with fibre glass matt membrane, for single or multi layer systems.

USES

Modo/P has been specifically designed for the waterproofing of foundations, basements, tunnels, terraces and roofs as a single layer or in a multi-layer system.

PART ID DESCRIPTION

742015 3.5MM 1 X 10M ROLL

INDEX FIDIA MINERAL GREYFidia Mineral may be used as the top layer in a two layer membrane system or as a single roof membrane for both new and renovation work.

USES

Fidia Mineral may be used as the top layer in a two layer membrane system or as a single roof membrane for both new and renovation work.

PART ID DESCRIPTION

742004 FIDIA MINERAL GREY 4.5KG

INDEX ARGO P3 mm thick, plastomeric, torch-applied, reinforced with polyester and stabilised with fibre glass matt membrane, for single or multi layer systems.

USES

Argo P is used as a continuous waterproofing membrane for foundations, basements, tunnels, roofs, etc, as an economical single layer membrane or as the base layer in multi-layer systems.

PART ID DESCRIPTION

742230 ARGO P 3MM


T O R C H A P P L I E D M E M B R A N E S

INDEX TESTUDO/TESTUDO MINERAL4 mm thick, elastomeric, torch-applied, reinforced with rot-proof non-woven single strand spunbond polyester fabric, membrane. Used in single or multi layer systems.

USES

Testudo is used as a continuous waterproofing membrane for foundations, basements, tunnels, roofs etc. Testudo Mineral may be used as the top layer in a two layer membrane system or as a single roof membrane.

PART ID DESCRIPTION

742040 4MM 1M X 10M ROLL

742060 MINERAL GREY 4.5KG 1M X 10M ROLL

INDEX MINERAL DESIGN 10P - CHECKER BOARD Waterproof membrane, self protected with ceramic granules in a “checker board” design. Gives the impression of a tiled / paved area. For the decoration and development of the “Design” roof. Mineral Design is a waterproofing membrane which combines, with its high water tightness performance, a decorative effect better than that by ordinary self-protected membranes. This adds value to the waterproofing work and solves environmental impact problems.

PART ID DESCRIPTION

771210 INDEX MINERAL DESIGN 10P - CHECKER BOARD 4.5KG

INDEX TESTUDO 30Torch applied 5 mm thick high performance reinforced elastoplastomeric polymer waterproofing membrane designed to be installed under hot asphalt.

USES

Testudo 30 membrane is characterised by a high resistance to puncture and is therefore particularly suitable for single layer waterproofing systems where high mechanical resistance is required.

PART ID DESCRIPTION

742046 5MM 1 X 10M ROLL

INDEX AUTOTENE ASFALTICOAutotene Asfaltico EP is a membrane which bonds with the heat of the bitumen paving laid over it. Its adhesion continues through use and is reinforced by the action of the traffic and solar action.

USES

Autotene Asfaltico EP is used for cold-state waterproofing of bridge and car park surfaces to be paved with hot bitumen or asphalt.

PART ID DESCRIPTION

771220 INDEX AUTOTENE ASFALTICO EP 4MM

INDEX AUTOTENE BASE PThermally self adhesive 3 mm thick waterproofing base sheet membrane.

USES

A waterproofing membrane which consists of distilled bitumen for industrial use, with a high content of elastomeric and plastomeric polymers.

PART ID DESCRIPTION

742011 BASE SELF ADH. WATERPROOFING

INDEX PROTEADUO SBS/APPHigh performance 4 mm thick torch applied waterproofing membrane with multilayer composite polymer bitumen and reinforcement

USES

Proteaduo/P has been developed as a waterproofing membrane where high mechanical resistance, elasticity, thermal stability and durability is required.

PART ID DESCRIPTION

742012 PROTEA DUO P COMPOSITE WATERPROOFING

INDEX DEFEND H ANTI-ROOT4 mm thick, elastomeric, torch-applied, plant root repellent, reinforced with rot-proof single strand spunbound non-woven polyester fabric, membrane.

USES

Defend H is always applied as the last waterproofing layer in contact with the earth for gardens, foundations, underground garages and tunnels covered with soil, road structures and roofs under gravel etc.

PART ID DESCRIPTION

771184 4MM 1M X10M ROLL


T O R C H A P P L I E D A C C E S S O R I E S

TORCH APPLIED ACCESSORIES

PRESSURE SEAL FLASHINGAluminium strips for sealing and flashing the edge of index sheet membranes.

USES

Parchem Pressure Seal Flashing is used to seal and flash the edge of Index membranes.

PART ID DESCRIPTION

752016 PRESSURE SEAL FLASHING 3M LENGTHS

HELASTO-RINGPlastic support ring for concrete pavers with leveling adjustment.

PART ID DESCRIPTION

771197 HELASTORING

771198 HELASTORING LEVELLER

TORCH ON PIPE DETAILING COLLAR Pipe Sealing - Torch on Pipe Detailing Collar in TPE (Thermoplastic Elastomer’s)

PART ID DESCRIPTION

744010 TORCH ON DETAILING COLLAR 15-130MM

TORCH ON DOMED GRATE 60 - 120mmTorch on leaf guard for drainage outlets (flexible)

PART ID DESCRIPTION

744090 TORCH ON DOMED GRATE 60-140MM

ONE WAY VENTSThe One Way Vent is a moisture relief device consisting of a two-piece polyethylene vent that allows moisture vapour to escape out of the roof deck system without allowing moisture to enter through the vent.

USES

One Way Vents are most commonly used in re-roofing applications. Blisters caused by internal moisture in “old” roofing systems may be prevented or reduced by using One Way Vents.One Way Vents allow for continual release of vapour from within the system, while maintaining the watertight integrity from the outside.

PART ID DESCRIPTION

744030 TORCH ON ONE WAY VENT 60MM

771183 TWO PIECE ONE WAY VENTS

GAS TORCHES & ACCESSORIESFor use with torch on membranes.

PART ID DESCRIPTION

742082 SMALL GAS TORCH, INCLUDING HOSE AND REGULATOR

742092 LARGE GAS TORCH, INCLUDING HOSE AND REGULATOR

771196 GAS TORCH HEAD LARGE

771195 GAS TORCH HEAD SMALL

771207 GAS TORCH STEM LONG 480MM

771206 GAS TORCH STEM SHORT 220MM

INTERNAL/EXTERNAL BITUMINOUS CORNERThe bituminous prefabricated corners are made by hot folding of a unique piece of bituminous membrane with composite reinforcement. The main advantage is the total melting to the waterproofing sheet allowing flexibility during installation, which will give a total waterproofing guarantee on the most risky points.

PART ID DESCRIPTION

744060 EXTERNAL BITUMINOUS CORNER

744040 INTERNAL BITUMINOUS CORNER

TORCH ON BITUMINOUS FILLET (BOND BREAKER)Like with the bituminous corner profiles, the torch on bituminous fillet (bond breaker) is obtained via the hot bending of a bituminous membrane with composite reinforcement. It has a length of 1100mm.

PART ID DESCRIPTION

744050 TORCH ON BITUMINOUS FILLET

ROOF DRAIN (DROPPER)Made of TPE (Thermoplastic Elastomer’s) with a 170mm spigotManufactured of a special compound of thermoplastic rubber, it is highly resistant against low temperatures (‘cold flexibility down to -40°) as well as perfectly compatible with all sorts of bituminous waterproofing membrane. The traditional dove-tail channels and special shagreens on the flange allow a perfect bond to the membrane making the seal 100% effective.

PART ID DESCRIPTION

744080 ROOF DRAIN 80MM

744070 ROOF DRAIN 100MM

PARAPETE DRAIN OUTLET - BOY TYPETPE (Thermoplastic Elastomer’s) angular drain - (Spitter) 100mm x 65mm x 90’ angle)

PART ID DESCRIPTION

744020 PARAPETE DRAIN OUTLET - BOY TYPE


T O R C H A P P L I E D A C C E S S O R I E S / C E M E N T I T I O U S M E M B R A N E S

INDEX BITUMEN PRIMERBitumen primer for all torch applied Index membranes.

PART ID DESCRIPTION

742105 INDEX BITUMEN PRIMER 20L

HDPE ROLLER970mm long pipe for rolling membranes out

PART ID DESCRIPTION

771200 HDPE ROLLER

CEMENTITIOUS MEMBRANESVANDEX BB75-ZSurface applied, cement based render, waterproofing barrier for positive and negative water pressure applications.

USES

Vandex BB75-Z is a cementitious membrane and does not rely on crystal growth to achieve its waterproofing. As a result, BB75-Z can be used on most masonry surfaces, including sandstone, provided that the surfaces are adequately prepared.

PART ID DESCRIPTION

751005 VANDEX BB75-Z 25KG

VANDEX BB75E-ZHigh performance, crack accommodating, surface applied, cement based render, waterproofing barrier for positive and negative water pressure applications.

USES

Vandex BB75E-Z is ideal in applications where the high pressure face is not easily accessible. It is also ideal for waterproofing the inside face of swimming pools, sewerage processing tanks, concrete block walls and any masonry surface where crystal growth waterproofing will not be effective due to a lack of alkalinity in the substrate.

PART ID DESCRIPTION

751003 VANDEX ELASTICIZER PK75 10KG PAK

VANDEX CONCRETE GREYConcrete capillary penetrating, crystal growth sealing, cement based, waterproofing system for positive and negative water pressure applications.

USES

Vandex Concrete Grey can be applied to either the pressure or non-pressure faces of concrete and is excellent for solving the problem of water seepage through porous or cracked concrete in both new and old structures.

PART ID DESCRIPTION

751011 VANDEX CONCRETE GREY 25KG

VANDEX CEMELASTFlexible, surface applied, cement based render, waterproofing barrier for positive and negative water pressure applications.

USES

Vandex Cemelast is excellent for solving the problem of water seepage through concrete and masonry where live cracks are present in both new and old structures.

PART ID DESCRIPTION

751009 VANDEX CEMELAST 9KG

VANDEX PLUGRapid setting, permanent plugging of water seepage through porous concrete and fast flowing water through cracks and construction joints in concrete and masonry.

USES

Applications include plugging in-situ and precast concrete segments in tunnels, water storage tanks, sewerage mains and processing tanks, basements, below ground car parks, access chambers, building foundations and mines.

PART ID DESCRIPTION

751006 VANDEX PLUG 15KG

VANDEX UNI-MORTAR 1-ZCement based reprofiling and waterproofing repair mortar - 6mm to 12mm thickness.

USES

Vandex Uni Mortar 1-Z is a surface applied, waterproof cementitious mortar for reprofiling concrete and masonry which does not rely on crystal growth to achieve its waterproofing. As a result, Vandex Uni Mortar 1-Z can be used on most masonry surfaces, including sandstone, provided that the surfaces are adequately prepared.

PART ID DESCRIPTION

751008 VANDEX UNI MORTAR 1-Z 25KG

VANDEX CONSTRUCTION JOINT TAPEWaterproof joint bandage for moving joints. Used with Vandex BB75E-Z or Cemelast.

PART ID DESCRIPTION

751010 VANDEX CONSTRUCTION JOINT TAPE

INDEX MINERAL CHIPS

PART ID DESCRIPTION

771201 INDEX MINERAL CHIPS GREY 5KG


CONCRETE REPAIR & PROTECTION


C O N C R E T E R E P A I R P R O D U C T S

AEGIS MSPCementitious floor topping internal/external trafficable waterproofing surface (2-4 mm thickness)

USES

Aegis MSP is particularly useful to resurface rain damaged concrete pavements or substrates which require a cementitious waterproof finish.

PART ID DESCRIPTION

752003 AEGIS MSP COARSE GREY 20KG PAK

752001 AEGIS MSP FINE GREY 20KG PAK

PATCHROC GPFloor / pavement patch repair, fast set mortar (15-75 mm depth)

USES

For the emergency reinstatement of localised patches in concrete pavements, airport aprons, access ramps, roadways and many industrial situations such as gangways and warehouse floors.

PART ID DESCRIPTION

402070 PATCHROC GP 20kg bag

PAVEROCFloor / pavement large area, repair mortar (15-50 mm depth)

USES

For the reinstatement of large areas of concrete pavements and floors to avoid the total replacement of bays.

PART ID DESCRIPTION

402080 PAVEROC 20kg bag

RENDEROC HBGeneral purpose, economical, patch repair mortar.

USES

For the reinstatement of large areas of concrete and for small, localised patch repairs. Renderoc HB will protect embedded steel reinforcement. It is specifically designed for vertical and overhead high-build applications.

PART ID DESCRIPTION

306095 RENDEROC HB 15kg

RENDEROC HB40High performance, medium weight, very low shrinkage, patch repair mortar, compatible with concrete 30-45 MPa

USES

For the reinstatement of large areas of reinforced concrete where low permeability characteristics are required and where higher compressive strength is an important consideration.

PART ID DESCRIPTION

302020 RENDEROC HB40 20kg

RENDEROC HB70High build, high strength, very low shrinkage, patch repair mortar, compatible with concrete >45 MPa

USES

For the reinstatement of localised patch repairs and largerareas where suitable reinforcement is incorporated. Renderoc HB70 is alkaline in nature and will protect embedded steel reinforcement.

PART ID DESCRIPTION

303030 RENDEROC HB70 20kg

PATCHROC C Floor / pavement patch repair, fast set mortar (25-200 mm depth).

USES:

For the emergency reinstatement of localised deep patches in concrete pavements, airport aprons, access ramps, roadways and many industrial situations such as gangways and warehouse floors.

PART ID DESCRIPTION

402060 PATCHROC C 20kg

RENDEROC HB25High performance, light-weight, very low shrinkage, patch repair mortar, compatible with concrete 15-30 MPa

USES

For the reinstatement of large areas of reinforced concrete where low permeability characteristics are required and where maximum compatibility with a compressive strength in the range of 15-30MPa

PART ID DESCRIPTION

387080 RENDEROC HB25 15KG

CONCRETE FLOOR REPAIRS REPAIR MORTARS FOR VERTICAL & OVERHEAD APPLICATIONS



RENDEROC LA55Super fluid, high strength, low alkali, micro-concrete reinstatement mortar, for form and pour applications

USES

Ideal for reinstatement of large, structural sections of concrete as well as for many smaller locations where difficulties of access make hand or trowel-applied mortars impractical.

PART ID DESCRIPTION

302030 RENDEROC LA55 20KG

RENDEROC FCFairing mortar screed, to cover surface imperfections, polymer modified - v(0 mm to 3 mm thickness)

USES

Renderoc FC cementitious fairing coat is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent cementitious fairing mortar.

PART ID DESCRIPTION

302000 RENDEROC FC 15KG

RENDEROC RAPIDExtremely fast setting, reinstatement mortar, trafficable within 2 hours.

USES

For fast reinstatement of bridge joint edges, roadway slabs, or where placement of localised areas is required. Renderoc Rapid is designed to accept traffic 1 - 2 hours after placement, enabling fast repairs and concrete replacements to take place, whilst minimising any traffic interruptions.

PART ID DESCRIPTION

200200 RENDEROC RAPID 20KG

RENDEROC BBHigh strength, low shrinkage mortar for the installation of elastomeric bridge bearings

USES

Renderoc BB exhibits a series of performance characteristics which make it ideal for use as a bearing mortar for the installation of elastomeric bridge bearings.

PART ID DESCRIPTION

200250 RENDEROC BB 20KG

GUNCRETE EHigh strength, low shrinkage, high build spray applied repair mortar

USES

For the reinstatement of large areas of concrete and for small, localised patch repairs in areas such as sea walls bridge decks and piers, tunnels, sewer pipes, etc.

PART ID DESCRIPTION

302060 GUNCRETE E 20KG



NITOMORTAR BHHigh performance epoxy resin blow hole and repair fairing mortar

USES

For filling in blow-holes, and eliminating minor irregularities in new and old concrete, prior to the application of Nitomortar and Nitocote epoxy systems.

PART ID DESCRIPTION

342270 NITOMORTAR BH BASE 5L

342280 NITOMORTAR BH HARDENER 2.5L

342290 NITOMORTAR BH FILLERS 5KG

NITOMORTAR APMulti purpose, epoxy adhesive repair paste, also used as an adhesive for Nitofill LV, and Emer-Band bandage systems

USES

For speedy and permanent patching repairs to concrete structures; bonding of precast concrete components and repair work to cementitious substrates where strength, impermeability to water, and resistance to aggressive chemicals is essential; emergency repairs to concrete structures and industrial floors in chemical handling and process areas.

PART ID DESCRIPTION

620460 NITOMORTAR AP 3LT PAK

620463 NITOMORTAR AP BASE 15L PAK

620464 NITOMORTAR AP HARDENER 15L PAK

NITOMORTAR 903Solvent free, general purpose, epoxy binder system

USES

For combining with selected fillers and aggregates to produce epoxy mortars of various consistencies. Also used as supplied, or with selected filler additions to produce bolt or starter-bar grouts, and as a priming system with some Durafloor epoxy flooring products.

PART ID DESCRIPTION

481015 NITOMORTAR 903 1.5L PAK

481025 NITOMORTAR 903 6L PAK

481019 NITOMORTAR 903 BASE 20L

481018 NITOMORTAR 903 HARDENER 10L

NITOMORTAR 908General purpose, high strength, epoxy patch repair mortar

USES

For speedy and permanent repairs to spalled concrete structures; bedding in of precast concrete beams; and all repair work to concrete and cementitious substrates where strength, impermeability to water, and resistance to aggressive chemicals is essential. Emergency repairs to concrete structures and industrial floors in chemical handling and process areas.

PART ID DESCRIPTION

340000 NITOMORTAR 908 BASE 20L PAK

340001 NITOMORTAR 908 HARDENER 20L PAK

340005 NITOMORTAR 908 10L PAK

EPOXY REPAIR PRODUCTS

NITOMORTAR ELTrowel-applied, high strength, high chemical and abrasion resistant epoxy liner system (3 mm to 12 mm thickness)

USES

For improving and bonding concrete repair mortars, cementitious floor toppings and screeds, waterproof renders and cementitious slurries. Cementitious mortars are alkaline in nature and will protect embedded steel reinforcement. Mortars produced with Nitobond SBR may be used for horizontal, vertical and overhead repair work.

PART ID DESCRIPTION

342095 NITOMORTAR EL 6L PAK

334411 NITOMORTAR EL BASE 15L PACK

334422 NITOMORTAR EL HARDENER 15L PAK

334433 NITOMORTAR EL FILLER 15L PAK

NITOMORTAR EL-HBHand-applied, trowel finished, high build, chemical and abrasion resistant epoxy repair mortar system (5 mm to 50 mm thickness)

USES

A high build epoxy mortar with maximum chemical and abrasion resistance for the protection of concrete and similar substrates. Ideal for rehabilitation of manholes, lining of outfalls, sewers and concrete structures.

PART ID DESCRIPTION

342250 NITOMORTAR EL-HB BASE 9L PAK

342255 NITOMORTAR EL-HB HARDENER 9L PAK

342260 NITOMORTAR EL-HB FILLERS 9L PAK



NITOMORTAR F4 FILLERSChemically inert fillers for use with Nitomotar 903 epoxy resin binder system.

PART ID DESCRIPTION

412060 NITOMORTAR F4 FILLERS 20KG

NITOCOTE EP500Spray-applied, trowel finished, high build, chemical and abrasion resistant epoxy liner system (5 mm to 20 mm thickness)

USES

A sprayable epoxy mortar with maximum chemical and abrasion resistance for the protection of concrete and similar substrates. Nitocote EP500 is simple and cost effective for overhead, vertical and horizontal resurfacing lining to both dry and damp (SSD) surfaces.

PART ID DESCRIPTION

336600 NITOCOTE EP500 GREY BASE 16L PACK

336610 NITOCOTE EP500 GREY HARDENER 16L PACK

NITOFILL LVLow viscosity, dual cartridge, epoxy crack-injection system

USES

Nitofill LV is designed for injecting cracks in concrete and masonry where there is a need to consolidate a structure or exclude water and air from contact with the reinforcement.

PART ID DESCRIPTION

344220 NITOFILL LV 450ML PAK

344221 NITOFILL/LOKFIX CARTRIDGE GUN

344222 NITOFILL LV FLANGE

344223 NITOFILL LV ADAPTOR

344224 NITOFILL LV STATIC MIXER/HOSE

344225 NITOFILL FLANGE TOOL

344215 NITOFILL LV 1.5L PACK

344214 NITOFILL LV 15L BASE PACK

344216 NITOFILL LV HARDENER 15L PACK

NITOPRIME ZINCRICHZinc-rich epoxy resin primer to protect steel reinforcement within repair mortars

USES

Nitoprime Zincrich is the recommended anti-corrosion primer for exposed steel reinforcement for use with Renderoc concrete repair mortars.

PART ID DESCRIPTION

322100 NITOPRIME ZINCRICH 1L

NITOBOND SBRWater resistant polymer additive, to provide good adhesion to concrete

USES

For improving and bonding concrete repair mortars, cementitious floor toppings and screeds, waterproof renders and cementitious slurries. Cementitious mortars are alkaline in nature and will protect embedded steel reinforcement. Mortars produced with Nitobond SBR may be used for horizontal, vertical and overhead repair work.

PART ID DESCRIPTION

323105 NITOBOND SBR 20L

323115 NITOBOND SBR 200L

NITOBOND HARPolymer emulsion bonding agent

USES

Nitobond HAR is the recommend primer for the Renderoc cement based repair mortars.

PART ID DESCRIPTION

320015 NITOBOND AR 5L

320005 NITOBOND AR 20L

322070 NITOBOND HAR 1L



NITOBOND EPEpoxy resin primer, high strength bonding agent to bond concrete substrate to repair mortars

USES

For bonding fresh wet cementitious materials to existing cementitious surfaces. For use on horizontal or vertical surfaces where mortar or concrete can be supported by formwork.

PART ID DESCRIPTION

321020 NITOBOND EP 1.5L PAK

321030 NITOBOND EP 6L PAK

PRIMERS FOR REPAIR PRODUCTS


P R O T E C T I V E C O A T I N G S

DEKGUARD SHigh performance, pigmented aliphatic acrylic, chloride ion and carbonation protective and decorative coating for concrete and masonry

USES

To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, sulphates, oxygen and water.

PART ID DESCRIPTION

560620 DEKGUARD S SPECIAL COLOUR 20L

560622 DEKGUARD S IN-CAN TINT 20L

561570 DEKGUARD S WHITE 20L

PROTECTIVE COATINGS

DEKGUARD E 2000Elastomeric, pigmented acrylic, chloride ion and carbonation protective and decorative coating for concrete and masonry

USES

To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen and water, especially where there are cracks within the substrate.

PART ID DESCRIPTION

560625 DEKGUARD E 2000 WHITE 15L

560626 DEKGUARD E 2000 SPECIAL COLOUR 15L

560628 DEKGUARD E 2000 IN-CAN TINT 15L

EMER-STOP S100NDeeply impregnating, iso-butyltriethoxy silane, clear liquid, water repellant and chloride ion protective treatment for concrete

USES

A deeply penetrating treatment designed to protect concrete from both water and chloride ingress whilst still permitting water vapour transmission out of the structure. Emer-Stop S100N is especially suitable for protecting concrete structures in marine and coastal environments.

PART ID DESCRIPTION

555147 EMER-STOP S100N 200L (177KG)

555148 EMER-STOP S100N 20L

DEKGUARD PRIMERA reactive silane-siloxane penetrating treatment on concrete surfaces for use with Dekguard S, Dekguard O and Dekguard Clear applications.

PART ID DESCRIPTION

561520 DEKGUARD PRIMER 20L

SILANE TREATMENTS

DEKGUARD OHigh performance, aliphatic acrylic, translucent protective coating for concrete and masonry

USES

To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, sulphates, oxygen and water. The product is also suitable to hide concrete repaired areas, and other visual differences with the host concrete.

PART ID DESCRIPTION

560700 DEKGUARD O 20L

NITOPRIME DGA reactive silane-siloxane primer with an acrylic component for use on porous substrates with a Dekguard topcoat system, for use with Dekguard E2000 and Dekguard Elastic applications.

PART ID DESCRIPTION

562600 NITOPRIME DG 20L

DEKGUARD ELASTICCrack-accomodating elastomeric, pigmented acrylic, chloride ion and carbonation protective coating for concrete and masonry

USES

To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen and water, especially where there are cracks within the substrate.

PART ID DESCRIPTION

560600 DEKGUARD ELASTIC WHITE 15 L

560621 DEKGUARD ELASTIC SPECIAL COLOUR 15L

560633 DEKGUARD ELASTIC IN-CAN TINT 15L


C O R R O S I O N P R O T E C T I O N

NITOCOTE SN502Penetrating silane-siloxane treatment to protect concrete and masonry against water and chloride ion penetration.

PART ID DESCRIPTION

555145 NITOCOTE SN502 20L

EMER-STOP CREMEDeeply impregnating, water dispersed, thixotropic creme, waterrepellant and chloride ion protective clear treatment for concrete

USES

A penetrating, thixotropic cream designed to protect concrete and masonry from both water and chloride ingress. Emer-Stop Creme is particularly useful for impregnating the exposed surfaces of reinforced concrete used in bridges, wharves, roads, on all atmospherically exposed concrete buildings and structures.

PART ID DESCRIPTION

555170 EMER-STOP CREME 200L

555180 EMER-STOP CREME 30L (25KG PACK)

NITOCOTE EP405Solvent free, epoxy resin coating system for potable water retaining structures on concrete and steel

USES

For lining and waterproofing potable water retaining structures and surfaces subject to contact with potable water. The cured film is corrosion, chemical and abrasion resistant and is suitable for application to reservoirs, tanks, silos, water treatment works, breweries, dairies, meat and food processing plants. The cured film is non toxic and meets the requirements of AS 4020.

PART ID DESCRIPTION

500010 NITOCOTE EP405 WHITE BASE 8L PAK

500015 NITOCOTE EP405 WHITE/BLUE HDNR 8L PAK

500020 NITOCOTE EP405 BLUE BASE 8L PAK

NITOCOTE EP410Highly chemical resistant, solvent free, epoxy coating system, for concrete and steel applications

USES

To provide protection to concrete and steel structures in aggressive chemical exposure or immersion conditions. The material is particularly suitable for applications in process plants and sewage works.

PART ID DESCRIPTION

500000 NITOCOTE EP410 GREY BASE 8L PAK

500005 NITOCOTE EP410 HARDENER 8L PAK

553050 NITOCOTE EP410 WHITE BASE 8L PAK

GALVASHIELD CC RANGEEmbedded galvanic sacrificial anode grid system for corrosion control and protection in, as yet, undamaged concrete

Various sizes available - please contact your local Parchem office for further information.

PART ID DESCRIPTION

312030 GALVASHIELD CC45




GALVASHIELD XPTEmbedded sacrificial zinc anode used with Renderoc repairs to extend the life of patch repairs in chloride contaminated concrete

PART ID DESCRIPTION

312015 GALVASHIELD XPT

GALVASHIELD XP2Next generation of Galvashield XP provides 2 times the performance of XP

PART ID DESCRIPTION

312040 GALVASHIELD XP2

GALVASHIELD XP4Next generation of Galvashield XP provides 4 times the performance of XP

PART ID DESCRIPTION

312025 GALVASHIELD XP4

CORROSION PROTECTION

EPOXY COATINGS

ZEMDRAIN MD SELF-ADHESIVEControlled permeability formwork liner for high quality durable concrete surfaces.

Zemdrain® MD self-adhesive can be used with all formwork but is particularly suited for special applications.

Zemdrain® MD self-adhesive is an addition to the range of Zemdrain® controlled permeability formwork liners which includes Zemdrain® MD.

PART ID DESCRIPTION

177350 ZEMDRAIN MD (2.5M X 35M) SELF ADHESIVE


GROUTS & ANCHORS


G R O U T S

CONBEXTRA HSUltra high strength, flowable, dual shrinkage compensated precision grout - (gaps 10 mm to 125 mm thickness)

USES

Used for free flow precision grouting in a wide range of applications. These include heavy duty support beneath machine base plates and bridge bearings.

PART ID DESCRIPTION

202000 CONBEXTRA HS 20KG

CONBEXTRA UWFormulated anti-wash out specialist grout for underwater grouting applications

USES

Conbextra UW is used for free flow or pumped grouting applications underwater or in tidal zones. There will be no significant ‘wash-out’ of the cement phase.Applications include bridge columns, quay pillars, concrete piling, slipways and dams.

PART ID DESCRIPTION

201030 CONBEXTRA UW 20KG

CONBEXTRA HFHigh fluid flow, dual shrinkage compensated, precision grout - (gaps 10 mm to 125 mm thickness)

USES

Conbextra HF is a Class A and C grout used for free flow precision grouting in a wide range of applications. These critical uses include heavy duty support beneath machine base plates and bridge bearings.

PART ID DESCRIPTION

201050 CONBEXTRA HF 20KG

CONBEXTRA HESHigh early strength, rapid setting, flowable, cementitious precision grout - (gaps 15 mm to 150 mm thickness)

USES

Conbextra HES is a Class C grout used for free flow grouting in a wide range of applications where rapid strength gain is a pre-requisite.

PART ID DESCRIPTION

201060 CONBEXTRA HES 20KG

CONBEXTRA GPGeneral purpose, high flow, shrinkage compensated grout - (gaps 10 mm to 100 mm thickness)

USES

Conbextra GP is used for general purpose grouting where it is essential to eliminate shrinkage when completely filling voids or grouting between a base plate and substrate, e.g. grouting of a stanchion base plate.

PART ID DESCRIPTION

201020 CONBEXTRA GP 20KG

CONBEXTRA CGeneral purpose, flowable, dual shrinkage compensated cementitious grout - (gaps 10 mm to 100 mm thickness)

USES

Conbextra C is a Class A and C, dual shrinkage compensated, cement based grout used for general purpose grouting where it is essential to eliminate shrinkage when completely filling the void between a base plate and a substrate.

PART ID DESCRIPTION

201040 CONBEXTRA C 20KG

CONSTRUCTION GROUTEconomical, class A shrinkage compensated grout

USES

Construction Grout is used for general purpose grouting when completely filling concrete voids or grouting between a base plate and a substrate e.g. the grouting of a stanchion base plate.

PART ID DESCRIPTION

201000 CONSTRUCTION GROUT 20kg bags

CEMENT BASED GROUTS


G R O U T S

CONBEXTRA EP10A highly fluid epoxy grout for dynamic/repetitive load applications gap width between 0.25-10mm

PART ID DESCRIPTION

223115 CONBEXTRA EP10 300ML PAK

CONBEXTRA EP65 PLUSA high performance epoxy grout for dynamic/repetitive load applications

PART ID DESCRIPTION

224460 CONBEXTRA EP65 PLUS BASE 14L PAK

224470 CONBEXTRA EP65 PLUS HARDENE 14L PAK

CONBEXTRA EP120A high performance two part epoxy grout for dynamic/repetitive load applications suitable for large volume pours

PART ID DESCRIPTION

222333 CONBEXTRA EP120 BASE 14L PACK

222444 CONBEXTRA EP120 HARDENER 14L PACK

EPOXY GROUTS

CONBEXTRA GROUT AGGREGATESized aggregates 1mm-5mm for bulking out large grout applications and some bulk cementitious flooring pours.

PART ID DESCRIPTION

202021 CONBEXTRA GROUT AGGREGATE 20KG

CONBEXTRA DEEP POURFlowable, precision cementitious grout for high volume and deep pours - (gaps 20 mm to 500 mm thickness)

USES

Conbextra Deep Pour is a Class A and C free flow precision grout for grouting gap applications ranging from 125 mm up to a maximum of 500 mm deep. Conbextra Deep Pour is formulated to minimise segregation and bleeding for deep grout pours.

PART ID DESCRIPTION

201070 CONBEXTRA DEEP POUR 20KG

ALOFIX MC HELPERDispersing agent for Alofix MC powder

PART ID DESCRIPTION

209095 ALOFIX MC HELPER 20L

ALOFIX MCMicrofine, cementitious soil stabilisation grout

PART ID DESCRIPTION

209090 ALOFIX MC 20KG


C H E M I C A L A N C H O R S

KEMFASTPolyester - For light to medium duty applications in hollow brick and blockwork

PART ID DESCRIPTION

PW-KF2 KEMFAST 380ml CARTRIDGE

PW-KF2.CASE KEMFAST PROFESSIONAL KIT 380ml

AC100 PROStyrene Free Vinylester - For remedial work in solid and hollow masonary

PART ID DESCRIPTION

PW-AC100PRO AC100 PRO 385ml

PW-AC100PRO-585 AC100 PRO 585ml CARTRIDGE

PFPRO / PURE 150 PROPure Epoxy - for high load applications.

PART ID DESCRIPTION

PW-PFPPRO PFPRO 385ml CARTRIDGE

PW-PFPRO-585 PFPRO 585ml CARTRIDGE

NOZZLES ADHESIVE

PART ID DESCRIPTION

PW-8482 NOZZLES ADHESIVE

BLOW PUMP

PART ID DESCRIPTION

PW-BLOWPUMP BLOW PUMP

4-IN-1 MULTI PRO DELIVERY SYSTEM

PART ID DESCRIPTION

PW-CGPRO 4-IN-1 MULTI PRO DELIVERY SYSTEM

CARTRIDGE GUN 4 IN 1 INJECTION TOOL

PART ID DESCRIPTION

PW-CGPRO-4 CARTRIDGE GUN 4 In 1 INJECTION TOOL

CHEMICAL ANCHORS

AC100EStyrene Free Polyester - For medium duty applications using standard applicator gun

PART ID DESCRIPTION

PW-AC-100E AC100E STYRENE FREE INJECT 300ml

PW-AC-100E.CASE AC100E PROFESSIONAL KIT 300ml


G R O U T S

The range of products will vary by location so please contact your nearest store for the range of products in stock. 1014

For any product or technical advice call your local Trade Store on

1300 737 787For Trade Store locations visit

www.parchem.com.au

National Head Office: 7 Lucca Road, Wyong NSW 2259 02 4350 5000 www.parchem.com.au

CONSTRUCTION PRODUCTS CATALOGUE - Plucka · PDF fileconstruction products 3 the complete range...

Documents

Transcript of CONSTRUCTION PRODUCTS CATALOGUE - Plucka · PDF fileconstruction products 3 the complete range...