Fall Protection – The Problem

• Falls are a serious safety concern in the jobsite.

• Falls are the leading cause of worker deaths in construction.

Scaffold in Dupage County

12 2 2013

Dec 2013

• MD• A man working in the

garage level of a row of town houses under slipped on a small patch of ice, fell and struck his head and died.

September 2013

Jan 2013

• Three story• Roofer fell off edge• Saved by fall arrest

Falls

• New OSHA standards in 1995

• 1954 ANSI Standards• Fatal injuries

involving falls increased by 20 from the preliminary count to 700 cases.

Fall Sources

Heights Falling?

Region V fatality data 2007-2011

What is Fall Protection?

• Fall protection protects workers from fall hazards. Fall protection doesn’t mean bulky or cumbersome equipment. It doesn’t interfere with work tasks and it doesn’t get in the way of coworkers – when used properly

Unguarded open-sided floor

Planning

• Sometimes it takes a lot of work to do things wrong.

• Elimination of fall hazards using the hierarchy of controls should be performed by all companies.

Hierarchy of Fall Protection

• Elimination – such as Cameras to monitor work. Elimination through design

• Passive Fall Protection – Guardrails, Covers

• Travel Fall Restraint• Administrative Control –

such as climber training, warning systems

• Fall Arrest

Cameras used to monitor locations.

Safety Program

• 1926.20(b)(1) requires all construction companies to have an effective accident prevention program.

• Identify where falls can occur to workers through Job Safety Analysis

• Discuss the method of protection the worker must use.

What Is Job Safety Analysis?

• Method used to break a job task into separate and distinct steps

• Four basic stages in conducting a JSA are: • selecting the job to be analyzed • breaking the job down into a sequence of steps • identifying potential hazards • determining preventive measures to overcome

these hazards • http://www.ccohs.ca/oshanswers/hsprograms/job-

haz.html has usefull examples of JSA’s

Training

Train workers:- When to use fall arrest- How to wear fall arrest- Inspection of

anchorages, lanyards, and harnesses

Inspections

• Conduct periodic inspections

• Is fall arrest is worn? • Is fall protection is

place?• Take pictures of

people doing it right

Inspection

• All fall protection equipment and anchorages must be inspected at the beginning of each eight-hour shift by an authorized person

• At least once per year (or more frequently if required by manufacturer) by a competent person or a competent rescuer as appropriate to verify equipment is safe for use.

• Written or electronic records of inspection should be kept on file for service life of product.

Enforcement• If people are not

wearing the fall arrest, what is the consequence?

Passive Fall Protection

• Guardrails • Strength = • Top rail height = • Mid-rail height = • Wire rope/chain

deflection of 2 inches

Covers

• Hold twice the weight• Secured• Marked

Violation: 4' x 8' sheets of plywood covering a stairway opening to the basement of a house. Only four nails hold the two covers. The cover is not marked.

Fall Arrest

• Personal fall arrest system means a system used to arrest an employee in a fall from a working level. It consists of an anchorage, connectors, a body belt or body harness and may include a lanyard, deceleration device, lifeline, or suitable combinations of these.

Free fall of 30 inches needs fall arrest not positioning

Travel Restraint

• 1000 lb anchorage• Cannot free fall to

lower level• On flat surfaces.

Work Positioning

• Positioning device system means a body belt or body harness system rigged to allow an employee to be supported on an elevated vertical surface, such as a wall, and work with both hands free while leaning.

• Work Positioning free fall cannot exceed 24 inches

• Max fall arrest force is 900 lbs.• Lanyards and harnesses used• Equipment must have minimum

breaking strength of• 5,000 lbs.

Fall Arrest Components

• Definition• Body Harness• Energy Absorbing

Lanyard• Anchorage

Fall Arrest

• Fall Arrest Force Maximum Allowed

• Harness = 1800 lbs.• Belt = 900lb (banned)

Workers wearing a body harness in an aerial lift

Fall Arrest

• Harness are required for fall arrests

• Belts are only for work positioning

• Maximum Fall Arrest Force should be less 1800 lbs for a harness.

One employee is not wearing fall arrest.

Lanyards

• Use energy absorbing lanyards or retractable lanyards.

• Check for ANSI Z359.1 or OSHA 1926.502 marking

• Calculate free fall distance

Harness

• Labeled meeting ANZI Z359 or OSHA 1926.502

• Use D-ring in back •Lanyard is not an energy absorbing lanyard.

•This is a chest waist harness for work positioning. Not designed for fall arrest.

Anchorages

• A secure point of attachment for lifelines, lanyards or deceleration devices

• 5000 lbs or 2:1 Safety factor is calculated by a qualified person.

• Anchorages may weaken over time due to weather or environment

Note: Put energy absorber at D ring end. Incorrect wearing shown.

Rescue

• Must be planned

• Following a fall, a worker may remain suspended in a harness. The sustained immobility may lead to a state of unconsciousness

• http://www.osha.gov/dts/shib/shib032404.html has more info on suspension trauma

Fall Prevention Techniques

• Handrails• Slip resistant threads• Slip resistant shoes• Fall restraint systems• Enclosed barriers

• Eliminate exposure for routine checks by cameras or instrumentation

• Build scaffold for long term exposure

Scaffolds

• OSHA 1926.451

• Training specific for erectors and users.

• Inspections before use

• Fall protection required above 10 feet.

• Suspended scaffolds need independent fall arrest from the scaffold

Scaffold Footing

• Baseplates always required.

• Mudsills needed if on earth.

Scaffold Planking

• Scaffolds must be fully planked, secured and overlapped.

• Falling object protection required.

• Inspect planks for damage or overloading.

Scaffold Guardrails

• Guardrails must be provided on all working platforms.

Scaffold Access

• Stairs are recommended

• Scaffold access ladders must be secured

Metal Bracket Scaffold

• What questions would you ask the scaffold erector for this job.?

Step Ladders

• Used on stable surface• Not used as a ext.

ladder• Inspected for defects• Never used on a

scaffold

Extension Ladder

• 4:1 Pitch• 3’ extension above

landing• No defects• Not near electrical• Secured from slipping

Fixed Ladder

• Stairs should be in place if used everyday. 1910.24

• Use fall arrest• Keep lanyard short to

12 inches if possible. • Inspect ladder for

looseness and proper rails to roof

Flat Roofs

• Inspect for damaged or rotten roof deck and components.

• Parapet must meets guardrail requirements

• Lifting at edge requires guardrail protection

• Warning lines and monitor required if not using conventional fall protection

Skylights

• Must cover them if working by them.

• Will not hold a person’s weight

Opensided Floors

• Need two rails or cables

• Fall height of 6 or more

• Cable rails allowed 2 inch deflection.

• Several falls into improperly guarded elevator shafts

Floor Holes

• Guardrails• Covers• Holes over 2”x2” are

covered under the std.• Beware covers that are

loose place over a hole.

Forklift Platforms

• Platform slides off• Improper rails• Pushes worker into

fixes object• Pallet unacceptable• Scissors point on

many carriages• Platform construction

Sloped Roofs

• Shinglers in residential must use fall arrest above 25’ or 8/12+ pitch

• Slideguards is required otherwise above 6 feet

Residential

• One of the most cited standards in construction

• 1926.503 requires specific training

• Falls from roofs, sheathing, truss erection, openings to basement are among many of the falls.

Sloped Roof

• Sheathers can use a Controlled Access Zone, Monitor, and Slideguards in lieu of fall arrest.

• Shinglers should use fall arrest and slideguards

• OSHA 1926.501(b)(13)

Extensible Boom Aerial Lifts

• Wear fall arrest• Must have smooth

surface to operate• Many flip in mud• Train operator in

manual instructions

Scissor Lifts

• Workers must be trained in the operation manual

• Full guardrails needed• Inspect area for holes

that could flip the lift• Ensure proper lighting

End chain is missing

Stairs

• Guardrails on side with both top and mid-rails

• Handrails• Evenly spaced threads• Foot clearance• Required if climbing

daily One handrail needed if both sides are enclosed

Steel Erection

• Ironworkers connecting out of an aerial lift.

• Fall Protection required at 15/30 feet when decking or connecting.

Safety Nets Used for Decking

Decking is the most common activity that historically killed iron workers

Nets used to protect deckers

Suspended Platforms

• Must follow 1926.550 (g) requirements

• Often not wearing fall arrest

• Platform must be proof tested

Metal Grating

• Must be secured with clips

• Guardrails provided on both sides.

Working Adjacent to Water

• Fall Protection• Life vests• Ring Buoys• Skiff or boat

Rebar Walls

• Work positioning• Rebar wall must have

spacing similar to a ladder to climb

• Rebar Walls must be adequately braced

Other Fall Surfaces

• Tail gates• Riding equipment

such as front end loaders and forklifts

Rescue

• The employer shall provide for prompt rescue of employees in the event of a fall or shall assure that employees are able to rescue themselves.

• 1926.502(b)(20)

Quick Quiz

• Anchorages must be _____ lbs.• Fall arrest forces for harnessing shall not exceed

_____ lbs.• What is the best in the hierarchy of fall protection?

_____________• Covers must hold _____ times the anticipated

load.• Free fall over ____ inches is not allowed in work

positioning.