Construction Chemicals

Page Header

417www.hilti.co.uk | 0800 886 100

www.hilti.ie | 1850 287 387

Construction Chemicals.

Hilti. Outperform. Outlast.

9

Construction Chemicals

Accredited Firestop Installation Information Page Test accreditations chart 419-420 Accredited Installers 421

Firestop Systems CP6 17 putty pads 422 CP 601S elastic firestop sealant 423 CP 606 intumescent acoustic fire mastic 423 CP 611 A intumescent firestop mastic 424 CP 660 expanding fire seal 424 CP 636 / CP 637 firestop compound 425 CP 638 firestop compound 426 CP 643N / CP 644 firestop collar 427 CP 645 firestop fire sleeve 428 CP 648 intumescent pipe wraps 429 CP 649 firestop wrap 429 CP 651N firestop pillow 430 CP 658 firestop plug 430 CP 657L firestop brick 431 CP 680 cast-in firestop device 432 CP 670 firestop acoustic board 433 CP 604 self levelling fire sealant 433 CP 672 / 672 FC firestop speed sprays 434

Foams CF 812 Air Sealer 435 CF 125-50 fire rated backing foam 436 CFI / CF-I 750 insulating foam 437

Adhesives CA 359 adhesive / dispensers 437

Concrete Repair Mortar CM 730-1 pourable grout 438 CM 510-1 epoxy repair mortar 438 CI 060 epoxy crack injection 438


Hilti. Outperform. Outlast. 4180800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ie


419www.hilti.co.uk | 0800 886 100

www.hilti.ie | 1850 287 387Hilti. Outperform. Outlast. Hilti. Outperform. Outlast.Hilti. Outperform. Outlast. Hilti. Outperform. Outlast.

CP 601S

CP606

CP611A

CP617

CP660

CP636

CP637

CP638

CP643N

CP644

CP645

CP648

CP649

CP651N

CP658

CP657L

CP670

CP604

CP672

CP680N

CF125-50

CP products Tested for*

Smoke Age Tested

At least 13 other types of test have been carried out covering properties such as, chemical compatability, explosion resistance, radiation resistance, mould resistance, electrical resistance, etc.

* For up-to-date test matrix refer to www.hilti.co.uk/cfsorwww.hilti.ie/cfs

Fire AcousticAir-seal

Fire Smoke Acoustic Age Tested

Fire Smoke Air-seal Acoustic Age Tested




Fire Smoke Air-seal Acoustic

Fire Smoke Air-seal Acoustic

Fire WITH MASTIC NOT APPLICABLE NOT APPLICABLE Age Tested

Fire WITH MASTIC NOT APPLICABLE NOT APPLICABLE Age Tested

Fire Acoustic Age TestedWITH MASTIC NOT APPLICABLE

Fire Acoustic Age TestedWITH MASTIC NOT APPLICABLE

FireWITH BACK-FILLING NOT APPLICABLE

Fire PLANNED Age Tested

Fire Smoke Age Tested



Fire Smoke Air-seal PLANNED Age Tested


Fire Smoke Acoustic Age Tested

Fire WITH MASTIC Air-seal Acoustic

Air-seal

NOT APPLICABLE NOT APPLICABLE

9


Hilti. Outperform. Outlast. Hilti. Outperform. Outlast. 4200800 886 100 | www.hilti.co.uk 1850 287 387 | www.hilti.ieHilti. Outperform. Outlast. Hilti. Outperform. Outlast.

CP 601S

CP606

CP611A

CP617

CP660

CP636

CP637

CP638

CP643N

CP644

CP645

CP648

CP649

CP651N

CP658

CP657L

CP670

CP604

CP672

CP680N

CF125-50

CP products Approvals and Testing*

* For up-to-date test matrix refer to www.hilti.co.uk/cfsorwww.hilti.ie/cfs

Pageno. 423

Pageno. 423

Pageno. 425

Pageno. 425

Pageno. 424

Pageno. 422

Pageno. 424

Pageno. 426

Pageno. 427

Pageno. 427

Pageno. 433

Pageno. 431

Pageno. 430

Pageno. 430

Pageno. 429

Pageno. 429

Pageno. 428

Pageno. 436

Pageno. 432

Pageno. 434

British StandardBS 476BS 476-20



















Pageno. 433

pr EN 1366-3

pr EN 1366-3

BS EN 1366-3

pr EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-3

BS EN 1366-4

PLANNED

FMAPPROVED

For Penetration Fire Stops.Consult the Factory Mutual Research Corporation Approval Guide.

R

C

LASSIFIED

FILL, VOID OR CAVITY MATERIALS CLASSIFIED BY

UNDERWRITERS LABORATORIES, INC.FOR USE IN TROUGH-PENETRATION

FIRESTOP SYSTEMS SEE UL FIRE RESISTANCE DIRECTORY

66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7

FMAPPROVED


R

C

LASSIFIED




66Y7


421www.hilti.co.uk | 0800 886 100


It is the combination of a Quality conscious and third party accredited Manufacturer working in close co-operation with a select group of third party accredited installers that can offer you the Best Value. Here are some of the benefits to you of utilising this co-operation:-

n Decrease your liability; liability that comes from poor or incorrect installation and performance of products

n Efficient Project Management based on the co-operation of a specialised manufacturer and contractor

n Commercially designed effective Fire Protection solutions

n Hilti and its products are approved by

the Loss Prevention Certification Board. Hilti currently has the only Passive Fire Resistant products of it’s type that are approved. This approval is an assurance of product and manufacturer quality, it can also have an affect on the building insurance premium. This can therefore reduce the service cost of the building.

n Solutions that have been tested for long term performance

n Solutions that offer business continuity and protections of premises

n Certificate of conformity of work completed

n Installation work audited by FIRAS on site to ensure compliance with manufacturers’ recommendations and Building Regulations

n Installer with site based manufacturer support

n Clear and comprehensive documentation of installation

n Comprehensive support documentation for product solutions

n Clarity and assistance on the role of Passive Fire measures in modern building construction

Further details of our accredited installers and the support we can offer you can be obtained by telephoning freephone08000838889(GBonly).

SQS 9001The Swiss association for Quality and management Systems (SQS) hereby certifies that Hilti (GB) Limited has an appropriate management system which meets the requirements of the international standard for quality management and quality assurance (ISO 9001) and has issued a certificate covering the whole company.

Cer

tified

Management System

ISO 9001

Cer

tified

Management System

ISO 9001

Reg No. 12455

ProductAccreditationHilti Firestop Systems have been certified by the Loss Prevention Certification Board. Products are monitored on an ongoing basis so you can have absolute confidence in the quality and standard of the product you are specifying.

InstallationAccreditationHilti-trained Specialist Contractors are also FIRAS-accredited. It means that they work to agreed industry standards, employ trained operatives and are subject to FIRAS on-site inspection.

RIBA CPD Network ProviderHilti is a member of the RIBA CPD Providers Network. The RIBA CPD Providers Network exists to provide quality assessed, in-house Continuing Professional Development, for architects and other construction professionals. The Providers Network aims to maintain, enhance or increase the RIBA members’ knowledge and skills.

AgeTestingHilti have tested the passive fire resistant products against a recognised standard for long term resistance to ageing. Details can be found at www.hilti.co.uk/cfsorwww.hilti.ie/cfs

AGE TESTED30 YEARS

Hilti

Don’t just use Hilti Firestop Products, use our

Accredited Firestop Installers

9



*Forinstallationinstructions,MSDS(CoSHH),technicaldataandapprovals,pleasevisitwww.hilti.co.uk/cfsorwww.hilti.ie/cfs

CP 617intumescent acoustic putty pad Never build another baffle box

Basematerials: Drywall.Forusein: Electrical sockets/switches, etc.Firerating: 2 hours.

CP 617 intumescent acoustic putty pad Packing Ordering Item no. contents designation (pcs)

CP617puttypad170x170(single) 20 CP617 39214CP617puttypad170x230(double) 20 CP617 39215

ProductdescriptionAn intumescent mouldable putty pad for use with plastic or metal back-boxes. Proven to re-instate the full acoustic performance of a RW=71dB specification drywall.

Areasofapplicationn All sizes of plastic or metal back-boxesn Can be used for commercial and residential applicationsn Acoustically rated drywalln General gypsum wall assembliesn Substitutes the need for baffle boxes

Productfeaturesn Pad can be moulded by hand to fit any size of outlet box n Quick and simple to install n Pads can be fitted to the inside or outside of the box. n Tested to EN1366-3 and BS476 to include 1hr and 2hr drywall on unsupported outlet boxes

Acousticsn Permitted for use in Robust Details n Accepted by NHBC n Tested in BG, Lafarge and Knauf walls*

You could save money and comply with Building RegulationsYou may believe that improving sound insulation and fire protection, to comply with the latest regulations, is expensive. But, when you use the Hilti putty pad, you could reduce costs whilst complying with all these requirements.

Contactustolearnmore.TofindyourlocalFireProtectionSpecialist,youcancallusormakearequestonlinenowat:www.hiltico.uk/cpadorwww.hilti.ie/cpad

Installed cost benefits Building regulations

n No baffle boxing n Up to 10 times faster

Complies with n Part B : Smoke and Flame n Part E : Acoustics plus n Electrically non-conductive

Sustainability

n Less plasterboard required n Minimum 30 year life

Robust Details Limited and NHBC

n Accepted by both these bodies n Full details available from your local Fire Protection Specialist

Robust Details

The Hilti CP617 intumescent acoustic putty pad has been accepted by Robust Details Ltd as an alternative mechanism of sealing the rear of electrical service penetrations, such as sockets, in Robust Detail timber frame and metal frame separating walls, as published in the Robust Details Part E Handbook.


423www.hilti.co.uk | 0800 886 100


310mlcartridge

CB200-P1

CP 601SElastic firestop sealantProductdescriptionA silicone based firestop sealant that provides ± 25% movement.Areasofapplicationn Expansion joints n HVAC penetrationsn Metal pipes (allows movement)n Top of wall jointsProductfeaturesn Halogen and solvent free n Weather and UV resistant n Joint widths from 6-150mm with mineral wool backing* n Joint widths up to 50mm with PE rod or CF125-50 foam*

Systemadvantages/customerbenefitsn Good adhesion without use of a primern Smoke, gas and water tightn Excellent movement capabilityn Unlimited linear length approved

Basematerials: Concrete, masonry, glass, metal, etc.Forusein: Walls and floors.Firerating: Up to 4 hours.


CP 606 Intumescent acoustic fire masticProductdescriptionAn acrylic based firestop mastic that offers ± 10% movement.Areasofapplicationn Sealing header jointsn Sealing drywall partition connectionsn Metal pipesn Rigid and low movement jointsProductfeaturesn Silicone free n Halogen and solvent free n UV resistant n Joint widths from 6-100mm back with mineral wool, PE rod or CF125-50 foam*

Systemadvantages/customerbenefitsn Paintable n Simple use and application n Smoke, gas and water tightn Easy clean up with watern Approved for infinite linear gap lengths

Basematerials: Drywall, masonry, concrete and metal.Forusein: Walls and floors.Firerating: Up to 4 hours.

Packaging Ordering Item no. contents (pcs) designation

Firestopsealant,white 20 (310ml) CP606 310638Firestopsealant,grey 20(310ml) CP606 310639Manualdispenser 1 (310ml) CB200-P1 055205Firestopsealant,white 540 (580ml) pallet CP606 310640Manualdispenser 1 (580ml) CB270-P1 024669Firestopsealant,white 1 (5 litres) CS606 373188NozzlesforCP606 3072291

CP 606 Intumescent acoustic fire mastic310mlcartridge580ml

CB200-P1 CS270-P1

Eachboxof20,580mlfoilscomewith4nozzleswhicharereusablewiththedispenser.Forbulkusers.Tobeusedwithfirestopcoatedboardsystems.

CP 601S elastic firestop sealant Packaging Ordering Item no. contents (pcs) designation

Firestopsealant,white 20 (310ml) CP601S 310633Firestopsealant,grey 20 (310ml) CP601S 310635Firestopsealant,anthracite 20 (310ml) CP601S 310634Manualdispenser 1 (310ml) CB200-P1 55205

9




CP 611A – pressure exertingintumescent firestop masticProductdescriptionA graphite based intumescent firestop sealant that will close combustible pipes and cables.

Areasofapplicationn Permanent sealing of single and bunched cables n Resealing penetrations formerly sealed with mortarn Tested with PVC, PP, PE, HDPE and ABS*n Sealing plastic pipes up to 50mm* Backed with mineral wool, PE rod or CF125-50 foam

Productfeatures n Expands in fire, protecting pipe and cable penetrationsn Smoke, gas and water tightn Halogen and solvent freen Odourless

CP 611A pressure intumescent Packing Ordering Item no. contents designation (pcs)

Intumescentfirestopmastic 20 CP611A 00382848Manualdispenser 1 CB200-P1 00055205

Systemadvantages/customerbenefitsn Easy to work with n Paintablen Particularly suitable for laying new cablesn Can be used for outdoor applicationsn Expansion pressure up to 7 Bar

Basematerials: Concrete, masonry, drywall and wood.

Forusein: Walls and floors.

Firerating: Up to 4 hours.

310mlcartridge CB200-P1

CP660 expanding fire seal

Applications:Permanent firestop seals in small and medium-sized openings (optimum size range: 100 x 100 mm to 300 x 300 mm) n Cable trays, bunched and single cablesn Openings accommodating pipes and cablesn Plastic pipes (can also be installed as a system in conjunction with Hilti firestop jackets and firestop wrap)n Metal pipes (uninsulated or with flammable or non-flammable insulation)(National approvals must be observed.)

CP 660 expanding fire seal

Ordering designation Package Item no. contents

CP 660expandingfireseal1 203517(incl. 1 mixing nozzle, instructions for use)

Install with standard Hilti HIT dispensers (MD 2000, ED 3500) and accessories (see section “Anchor Systems”)

Advantages:n 3-phase curing – the fireseal can be easily moulded by hand n Clean installation without need for formwork or other aidsn Very quick and easy to install – a reliable firestop seal with only one

productn Easy subsequent installation of additional cablesn Outstanding sound insulation properties thanks to flexible foam

structure acoustic data availablen Smoketightness and firestopping with one system

Basematerials: Drywall, concrete, masonry.

Forusein: Walls and floors.

Firerating: Up to 2 hours in walls. Up to 3 hours in floors


425www.hilti.co.uk | 0800 886 100


CP 636 firestop compoundProductdescriptionA fire resistant, cement based compound with thermal insulating properties for sealing small to large sized openings where further penetrations may be required.

Areasofapplicationn Cables and cable traysn Ductwork dampersn Metal pipes

Productfeaturesn High yield n Stiff (forms not always required) n Contains no asbestos, phenol or halogen constituents n Good adhesion to steel, concrete and masonry n DIN 4102 class B1

sodfm,ev iJdjfiwhriuh. NöoWEZ8Z 23awöp3i4eß0288u27 uze4i5kirdwiloi4jtf-öx-.vbvbvh, ireivu9+ß12oeoo

CP 636 Brandschutzmörtel

CP 636 firestop compound

Packaging Ordering Item no. contents designation (pcs)

Firestopcompound, 1 CP636-20 0033489720kgsack

Systemadvantages/customerbenefitsnPaintablenSimple application by trowel

Basematerials: Concrete and masonry.Forusein: Walls.Firerating: Up to 4 hours.

RecommendationsforusenMix the compound in the ratio of approx. 3 :1 (compound to water).Stir the compound into the water

CP 637Structural firestop compoundProductdescriptionA fire resistant, gypsum based compound with thermal insulating and acoustic properties for sealing medium to large sized openings where further penetrations may be required.

Areasofapplicationn Cables and cable traysn Combustible pipesn Non combustible pipes

Productfeaturesn Quick setting n Low shrinkage n Good adhesion to steel, concrete and masonry

Basematerials: Concrete, masonry.Forusein: Firestopping med/large openings.Firerating: Up to 4 hours.

CP 637 structural firestop compound

Packing Ordering Item no. contents designation (pcs)

CP637firestopcompound 20 CP637 00340785


IMPORTANT ContactyourlocalFireProtectionSpecialistat: www.hilti.co.uk/cfsorwww.hilti.ie/cfs foradviceonuseasaload-bearingseal.

9



CP 638 High-strength structuralfirestop compoundProductdescriptionA fire resistant, gypsum based compound with thermal insulating and acoustic properties for sealing medium to large sized openings where further penetrations may be required.

Areasofapplicationn Cables and cable traysn Combustible pipes n Non combustible pipes n Ductwork dampers

Productfeaturesn Quick setting n Expands when set to provide smoke seal n Good adhesion to steel, concrete and masonry

Basematerials: Concrete, masonry.Forusein: Large openings (with structural requirements).

Firerating: Up to 4 hours.

CP 638 high strength structural firestop compound Ordering Item no. designation

IMPORTANT ContactyourlocalFireProtectionSpecialistat: www.hilti.co.uk/cfsorwww.hilti.ie/cfs foradviceonuseasaload-bearingseal.


CP638firestopcompound CP638 00340646


427www.hilti.co.uk | 0800 886 100


Systemadvantages/customerbenefitsn Quick and easy closure without use of a tooln Great in tight corners (brackets repositionable)n Reduces noise transmission from pipes to structure (foam insert) n Collar stays in place whilst fixing (foam insert grips pipe)

CP643N firestop collarProductdescriptionA ready to use firestop collar made of a galvanised steel housing and intumescent inserts for firestopping combustible pipes. Areasofapplicationn PVC, HDPE, PP, ABS pipes*Productfeaturesn Fixing brackets can be moved n Ready to use no tools required for installation n Simple and rapid installation by hand

CP643N firestop collar Forpipe Packaging Ordering Item no. OD (mm) contents Designation (pcs)

Firestopcollar 32-51 1 CP643N-50/1.5" 304325Firestopcollar 52-64 1 CP643N-63/2" 304326Firestopcollar 79-91 1 CP643N-90/3" 304328Firestopcollar 92-115 1 CP643N-110/4" 304329Firestopcollar 116-125 1 CP643N-125/5" 304330Firestopcollar 126-170 1 CP643N-160/6" 304331All the above include fixing bracketsLarger diameter collars available on request.

CP 643N

CP 643N

Basematerials: Concrete, masonry and drywall.Forusein: Walls, floors.Firerating: Up to 2 hours.

Caution–Mostotherfirestopcollarsareunsuitable(un-tested)

fordrywall.Pleasechecktestdatacarefully.

CP 644 firestop collar

ProductdescriptionA high-specification version of the CP 643N collar, provides longer fire sealing and can deal with notoriously “difficult” plastic pipe materials.

CP 644 firestop collar Forpipe Packaging Ordering Item no. OD (mm) contents Designation (pcs)

Firestopcollar 32-51 1 CP644-50/1.5" 00304332Firestopcollar 52-64 1 CP644-63/2" 00304333Firestopcollar 79-91 1 CP644-90/3" 00304335Firestopcollar 92-115 1 CP644-110/4" 00304336Firestopcollar 116-125 1 CP644-125/5" 00304337Firestopcollar 126-170 1 CP644-160/6" 00304338Firestopcollar 171-180 1 CP644-180/7" 00304339Firestopcollar 181-200 1 CP644-200/8" 00304340Firestopcollar 201-225 1 CP644-225/9" 00304342Firestopcollar 226-250 1 CP644-250/10" 00304343All the above include fixing brackets

CP 644

Basematerials: Concrete, masonry and drywall.Forusein: Walls, floors.Firerating: Up to 4 hours.

Areasofapplication• PVC, PVCC, PVC HI pipes• HDPE, PP, ABS, B1 / B2 pipes

s – PLEASE ASK FOR DELIVERY DETAILS.

ssssssssss


9




CP645 intumescent fire sleeveProductdescriptionAn intumescent pipe sleeve for sealing combustible, insulated or metal pipes. Maintains both thermal and vapour seal.

Areasofapplicationn Combustible pipes (PVC, PP, ABS and Pb up to 168mm)*n Steel pipes up to 168mm* n Copper pipes up to 75mm* n Off-cuts tested taped together n Single cables up to 50mm and bunched cables*

Productfeaturesn Simple to install n One sleeve can replace up to 6 collars n Easily cut to size

CP645 intumescent fire sleeve Packaging Ordering Designation Item no. contents (pcs)

FireSleeve-17mmbore 6 CP 645-17 284690FireSleeve-21mmbore 6 CP 645-21 284691FireSleeve-27mmbore 6 CP 645-27 284692FireSleeve-34mmbore 6 CP 645-34 284693FireSleeve-42mmbore 6 CP 645-42 284694FireSleeve-48mmbore 6 CP 645-48 284695FireSleeve-54mmbore 6 CP 645-54 284696FireSleeve-60mmbore 6 CP 645-60 284697FireSleeve-67mmbore 6 CP645-67 284698FireSleeve-76mmbore 6 CP 645-76 284699FireSleeve-80mmbore 6 CP 645-80 284700FireSleeve-89mmbore 6 CP 645-89 284701FireSleeve-102mmbore 6 CP 645-102 284702FireSleeve-108mmbore 6 CP 645-108 284703FireSleeve-114mmbore 6 CP 645-114 284704FireSleeve-127mmbore 6 CP 645-127 284705FireSleeve-140mmbore 6 CP 645-140 284706FireSleeve-159mmbore 6 CP 645-159 284707FireSleeve-169mmbore 6 CP 645-169 284708

Systemadvantages/customerbenefitsn Simple to installn No fixings – no special toolsn Allows for thermal movement of pipesnCan be fitted flush to solid wallsn Maintains vapour seal of existing insulation

MaintaininginsulationwithaestheticfinishCan be mounted flush to the wall dependant on base material or left proud to allow connection to existing insulation.

Each sleeve is 300mm in length and comes with a strip of repair tape.

Basematerials: Concrete, masonry, drywall, CP670Forusein: Walls, floors.Firerating: Up to 2 hours.


429www.hilti.co.uk | 0800 886 100



CP 648 intumescent pipe wrapsProductdescriptionHigh specification firestop wraps for sealing flammable pipes.

Areasofapplicationn Sealing flammable plastic pipes from 50-160mm with high and low wall thicknessn Pipes include: UPVC, ABS, PP, PE

Productfeaturesn Special elastic material for good pliability n Halogen and plasticizer free n Water resistant n High performance fire expansion rate (40:1) n Seal with CP611A or appropriate compound (CP636, CP637 or CP638)

CP 648 intumescent pipe wraps Quantity Ordering designation Item no.

FirestopSingleWrap 2 CP 648-S 50/1.5" 286076FirestopSingleWrap 2 CP 648-S 63/2" 286077FirestopSingleWrap 2 CP 648-S 90/3" 286079FirestopSingleWrap 2 CP 648-S110/4" 286080FirestopSingleWrap 2 CP 648-S125/5" 286081FirestopSingleWrap 2 CP 648-S160/6" 286082FirestopEndlessWrap 1 CP 648-E-W45/1.8" 286083Easy to measure, easy to cut, easy to handle. The only wrap you need for plastic pipes up to 6”.

Systemadvantages /customerbenefitsn Very fast installationn CP 648-S is ready to use (precut)n CP 648-E can be cut to length to suit the pipe n Extremely thin wrap thicknessn Simply insert wrap strip into annular spacen Minimum space required - ideal for limited penetration

accessibility (ideal for bent pipes etc.)n Easy to fasten with integrated adhesive closing tape

Basematerials: Concrete, masonry.Forusein: Walls, floors.Firerating: Up to 4 hours.

CP 648-S pre-cut ready to fit

CP 648-E a 10m roll which you cut to suit your pipe diameter

CP 649 Intumescent pipe wrapProductdescriptionA flexible intumescent graphite strip contained within a polyethylene sleeve.

Areasofapplicationn PVC pipes

Productfeaturesn Ready to use wrap – no preparatory work required n Easy to fasten in place n Seal with CP611A or appropriate compound (CP636, CP637 or CP638)

Systemadvantages/customerbenefitsn Simple to use intumescent sealn Little space required – ideal where pipes run close together

CP 649 intumescent pipe wrap Packaging Ordering Item no. contents (pcs) designation

2HrPipewrap 1 CP649/55 002856362HrPipewrap 1 CP649/82 002856372HrPipewrap 1 CP649/110 002856382HrPipewrap 1 CP639/160 00285639Wrapsforlargerdiameterpipesareavailableonrequest.

Basematerials: Concrete and masonry.Forusein: Walls and floors.Firerating: Up to 2 hours.

9




sodfm,ev iJdjfiwhriuh. NöoWEZ8Z 23awöp3i4eß0288u27 uze4i5kirdwiloi4jtf-öx-.vbvbvh, ireivu9+ß12oeoo

CP 651 Brandschutzkissen

CP 651N firestop pillow Packaging Ordering Item no. contents designation (pcs)

Firestoppillow(large) 6 CP651N-L 382626L/W/H: 300x170x30 mmFirestoppillow(medium) 15 CP651N-M 382625L/W/H: 300x80x30 mmFirestoppillow(small) 30 CP651N-S 382624L/W/H: 300x40x30 mm

Systemadvantages/customerbenefitsn Excellent for laying new cablesn Tear-resistant and dust-free pillows for dust-free roomsn Easy installation without use of a special tooln Re-usable, thus economical in usen A flexible system (temporary or permanent firestop)n Also for use in drywallnAge tested for 30 years

CP 651N firestop pillowProductdescriptionAn intumescent graphite based product encased in an inner polyethlene bag inside an outer woven fibreglass bag. Areasofapplicationn Applications for permanent or temporary seal n Installations where frequent changes may be requiredn Dust free applications in switch or computer roomsn Cable trays and inside cable trunking*n PVC pipes up to 50mm diameter* Productfeaturesn Dust free and tear resistant n Suitable for temporary and permanent installations n Durable and resistant n Odourless n Expands to 1.3 times

Basematerials: Concrete, masonry and drywall.Forusein: Walls and floors.Firerating: Up to 4 hours.

CP 658 intumescent firestop plugProductdescriptionA ready to use intumescent flexible plug composed of a two component polyurethane foam.Areasofapplicationn Sealing of 50mm - 200mm circular penetrationsn Sealing bunched or single cables through wall and floorsn Perfect in dust free environments n Suitable for both temporary and permanent applications Productfeaturesn Free from dust and fibres n Halogen and solvent free n Can be painted

sodfm,ev iJdjfiwhriuh. NöoWE

Z8Z 23awöp3i4eß0288u27 uze

4i5kirdwiloi4jtf-öx-.vbvbvh, ireiv

u9+ß12oeoo

CP 656 Brandschutzstopfen

CP 658 intumescent firestop plug Packaging Ordering Item no. contents designation (pcs)

Plug,62mmdia. 20 CP658-62 00369293Plug,77mmdia. 20 CP658-77 00369294Plug,107mmdia. 20 CP658-107 00369295Plug,158mmdia. 20 CP658-158 00369297Plug,202mmdia. 20 CP658-202 00369298Intumescentmastic(310ml) 20 CP611A 00382848Manualdispenser 1 CB200-P1 0005520

Systemadvantages/customerbenefitsn Especially suitable for laying new cables latern Economical in use owing to short installation timen Easy installation as no special tool is requirednImmediately functional after installationnVersatile in use (temporary or permanent protection)


s – PLEASE ASK FOR DELIVERY DETAILS.

sssss


431www.hilti.co.uk | 0800 886 100



CP 657L intumescent firestop brickProductdescriptionA ready to use intumescent flexible brick composed of a two component polyurethane foam mixed with graphite.

Areasofapplicationn Sealing single or multiple penetrations in small to medium openingsn Temporary or permanent sealing of cables and cable traysn Temporary or permanent sealing of flammable pipes n Temporary or permanent sealing of insulated metal pipes n Temporary or permanent sealing of non insulated metal pipes

Productfeaturesn Free from dust and fibres n Halogen and solvent free n Operational immediately after installation n Can be painted

CP 657L intumescent firestop brick

Packaging Ordering Item no. contents designation (pcs)

Firestopbrick 20 CP657L 00383523Firestopsealant,310ml 12 CP611A 00382848Manualdispenser 1 CB200-P1 00055205

Systemadvantages/customerbenefitsn Particularly suitable for laying new cables latern Economical in use owing to short installation timen Easy installation as no special tool is requirednIdeal for use in floors as no formwork is requiredn Immediately functional after installation


Seepage335forML30Channel

9




Health and Safety with Installed Cost Benefits

CP 680N Intumescent Cast-In Firestop DeviceProductdescriptionA polypropylene body containing an insert of intumescent material. An elastic sealing membrane allows for flexibility to use with differing pipe materials with different diameters.

Areasofapplicationn Sealing pipes from 1.5" (25 mm) up to 6" (160 mm) in penetrations through fire rated floor compartments. n Suitable for: – Plastic pipes: PVC, uPVC, PE, HDPE, PP, PP-R* – Metal pipes: steel, copper; EMT, conduit/cables* – Insulated steel and copper metal pipes*

Productfeaturesn Ready-to-use devicen One step installation resulting in greatly reduced installation timen Water and smoke tightn Excellent pipe-to-structure sound insulationn Allows for pipe movement and vibrations during and after installation

Keycustomerbenefitsn The most economical way to seal pipes through floorsn One step installationn No diamond drillingn No working at height to fit collars/wrapsn No additional mastic or back-filling requiredn Plastic lid stops rainwatern Only three devices to cover all pipe diameters from 1.5" (25 mm)

up to 6" (160 mm)n Easy to remove and replace pipesn Allows for pipe adjustments during installation

CP 680N Cast-In Firestop device Packaging Ordering Item No content (Pcs) designation

Cast-inFirestopdevice 18 CP680N-75/2.5"(1) 00282694Cast-inFirestopdevice 8 CP680N-110/4"(1) 00282695Cast-inFirestopdevice 4 CP680N-160/6"(1) 00282696Metal-deckadaptor 1 CP680N-75/2.5"(2)00333551Metal-deckadaptor 1 CP680N-110/4"(2) 00333552Metal-deckadaptor 1 CP680N-160/6"(2)00333553

(1)

(2)

Basematerials: Concrete.Forusein: Floors.Firerating: Up to 3 hours.

Improving Health and Safety during construction often costs money.Here is one of those astonishing innovations which could bring you real cost reductions whilst improving site safety

Contactustolearnmore.TofindyourlocalFireProtectionSpecialist,youcancallusormakearequestonlinenowat:www.hiltico.uk/ccastorwww.hilti.ie/ccast

Installed cost benefits Health and safety

n No diamond drilling n No boxing out the openings n No collar or wrap n No need to backfill

n No trip hazard (no plywood nailed over holes) n No falling cores (from diamond drilling) n No working at height to fix collars n No drilling overhead n No working at height to shutter for back-filling around wraps

Sustainability

n No concrete waste from coring holes n Minimum 30 year life

Helps construction run smoothly

n Less contracts to award n Eliminates rainwater ingress from cored or cast holes n Accommodates misalignment


433www.hilti.co.uk | 0800 886 100



CP 670 Firestop acoustic board Basematerials: Drywall, masonry, concrete.Forusein: Walls and floors.Firerating: Up to 4 hours.

CP670 Firestop acoustic board Ordering designation Packaging cont. (pcs) Ordering designation Item no.

FirestopAcousticBoard 4 CP670 284225FirestopAcousticBoard 20 CP670 284301FirestopAcousticBoard 40 CP670 376024FlexiCoating1) 1(6.5kg) CP670-C 3760231) Additional coating only required on high performance seals*Seal joints with CP 606 Firestop Sealant (see page 423)

CP672

CP604

ProductdescriptionA self-levelling, single component silicone based firestop sealant. For use with through penetrations as well as construction joints in floors.

Areasofapplicationn Sealing curtain wall/slab edge detail n Sealing small-medium sized openingsn Sealing non combustible pipes

Productfeaturesn Self-levelling requires no tooling n Excellent elongation/compression properties n Resistant to smoke and water n Halogen and solvent free

CP604 Self-levelling Fire Sealant

CP604 Self-levelling Fire SealantDescription Package Ordering Item contents designation no.

Selflevellingfireseal 15 litres CP604grey 00369177

Systemadvantages/customerbenefitsn Simple use and application n Smoke, gas and water tightn Waterproof within 3 hours

Basematerials: Concrete, Curtain wall.Forusein: Floors, Curtain wall joints.Firerating: Up to 4 hours.

ProductdescriptionAn innovative system for fast, reliable and cost effective firestopping of wall and floor openings.

Areasofapplication*n Extended approvals for large diameter cables, dampered penetrations and double board usagen Single cables, cable bundles, cable tray air ducts and pipesn Non combustible pipesn Combustible pipes (in conjunction with other products) n Large penetrations possible up to 5 metres high or with an unrestricted length.

Productfeaturesn Pre-coated board, 1200 x 600 x 50mm n Odourless and solvent free n Less prone to damage due to pliancy of the material and the resilient elastic coating n Approved for a wide range of applications* n Fast tight seal, less sealant required for gap filling

9



CP 672 / CP672 FC firestop speed sprays

TechnicalData CP 672 CP 672FCChemical basis / Water-based acrylic dispersion/approx. 8 pH value Consistency Sprayable liquid, brushable Density 1.25 g/cm3 (10.43 lb/gal)Application temperature + 5° to +40°C (40°F to 104°F)Color red, white, gray gray Shelf life 12 months 9 monthsRain-resistant skin- 5°C 25°C 40°C 5°C 25°C 40°C forming time at 80% (41°F) (77°F) (104°F) (41°F) (77°F) (104°F) relative air humidity and 55 h 35 h 20 h 15 h 7.5 h 4.5 h 3 mm coating thickness in well-ventilated rooms:

Advantagesn Flexibility to withstand considerable joint movementn Very fast installation – saves labour and timen Easy spray or brush applicationn Good sound-proofing qualitiesn Water, mould and mildew resistantn Resistant to ageingn Smoke-tight and virtually air-tightn Maximum flexibility – withstands over 500 flex cycles (ASTM E 2307)n Spray equipment can be easily cleaned with water (no solvents required)n Can be painted over

ApplicationsFirestopping solution forn Perimeter joints with a width of up to 200 mm between floor slabs and

curtain walls (CP 672 and CP 672 FC)n Joints between walls and ceilings (CP 672)

Bauchemie Piktos_neu.ai05.11.2007

SchallschutzRauch- und Gasdichtigkeit

Wasserbeständigkeit Elektische

30years

30Jahre

45%

Dampfdichtigkeit Wärmedämmend

Air-seal/Luftdichtheit

Smoke and gas-tight, integrated smoke seal

Water resistant, W-rating tested

Fire resistance tested in realistic, full-scale curtain wall set-up, CP 672 (ASTM E2307/ EN 1364 part 4), CP 672 FC (ASTM E2307)




30years

30Jahre

45%



Resistant to aging and tested to ensure a service life of at least 30 years




30years

30Jahre

45%



Ordering designation Bucket contents Color Shelf life Item no.

CP 672 19 l white 12 month 385383CP 672FC* 17 l grey 9 month 288383* Only for curtain walling




30years

30Jahre

45%



CP 672 CP 672FC

FMAPPROVED

FILL. VOID OR CAVITY MATERIAL FOR USE IN JOINT SYSTEMS AND PERIMETER FIRE CONTAINMENT

SYSTEMSSEE UL FIRE RESISTANCE DIRECTORY 66Y7

Hilti CP 672 is the universal firestopping solution for wall-to-ceiling joints as well as curtain walling.

CP 672 and CP 672 FC are quick and easy to apply and achieve an excellent bond.

Fire resistance test reports, approvals and certificates normally do not contain any information on the service life of a firestop product or assembly. By carrying out its own additional ageing tests which simulate extreme temperature and humidity conditions, Hilti provides a very high level of information on product reliability and the service life expectancy of Hilti firestop systems. On the basis of the ageing cycles obtained in these test procedures and the experience gained in the field of concrete construction, it can be assumed that Hilti firestop systems have a service life (ageing resistance) of approximately 30 years from manufacturing date.

Please note that this expected long-term ageing resistance of Hilti firestop systems, which is given on the basis of the above-mentioned tests, depends on a number of factors on which Hilti basically has no influence (e.g. environmental factors such as extreme environmental conditions, e.g. chemicals, etc.) and, therefore, is subject to the following conditions which must be strictly observed by the user with regard to the respective Hilti firestop system:

• Strict adherence to Hilti’s operating, setting, installing and other technical instructions• Rigorous compliance with all other conditions set out in the respective specifications during the lifetime of the Hilti firestop systems, in particular with regard to regular control and

maintenance as well as to foreseeable use under normal climatic conditions in the respective field of application.

Acoustic insulation sound transmission classification 55(ASTM E90-99)

Mixing paddles Ordering designation Paddle diameter Total length Item no.

TE-MP 80 80 mm 500 mm 41215TE-MP 110 110 mm 600 mm 41216

TE-MP 80


435www.hilti.co.uk | 0800 886 100


CF 812 Air SealerProductdescriptionCF 812 air sealer makes air sealing simple and will help save energy and improve building performance. CF 812 maintains air barrier properties and outperforms many other materials.

Areasofapplication-buildingenvelopejointssuchas:n Top of wall jointsn Wall-to-beam

Productfeaturesn Elastic formulation allows movementn Low pressure build; does not distort the jointn Excellent adhesionn Moisture curedn Ozone friendly propellant

Air Sealer Package Item no. contents

CF812AirSealer 1 can (600 ml) 385680Available as single cans, boxes of 12 and pallets of 144

Features:The special low pressure, flexible formula of Hilti CF 812 and the resuable Hilti DS-1 dispenser represent the leading foam system available today. It provides outstanding dosing control and a safe, efficient way to air seal windows, doors and skylights.

Systemadvantagesn Forms air-tight, water-resistant sealn Soft, flexible foam allows joint movementn Low expansion after dispensingn Provides excellent sound barriern High quality valve prevents presssure loss, prolongs shelf life and

prevents clogging of foam n Uses a low global warming hydrocarbon propellant

Accessories Package Item no. contents

CFDS-1dispenser(standardlength) 1 259768CFDS-1700dispenser(700mm) 1 209692CF-R1cleaner 1 can (500ml) 024506

LowPressureBuild:After injection, standard foams continue to expand. In a confined space, this leads to a pressure build which can distort the joint, so opening new gaps. CF 812 Air Sealer is proven to exert very low pressures so minimising distortion.


9


CF 125-50 Fire Rated Backing Foam ProductdescriptionCF 125-50 fire rated backing foam is a one component ready-to- use polyurethane system, which is used in conjunction with firestop sealants.

Areasofapplicationn Insulating and sealing doors and windows in fire rated building elementsn Backfilling around service penetrations prior to being used as backing material for CP 601, CP 606 and CP 611A Passive Fire Resistance sealants and mastics

Productfeaturesn Excellent adhesionn Moisture curedn Ozone friendly propellant Environmentalfeatures:

nContains no CFC’s.nContains no formaldehyde.nPhysiologically harmless when cured.nPropellant meets requirements of 1987 Montreal Agreement.

CF 125-50 Fire Rated Backing Foam Package Ordering Item no. contents designation

Fireratedbackingfoam 12 CF125-50 00259625Foamcleaner 12 CFR1 00024506Dispenser 1 CFDS1 00259768

Systemadvantagesn High foam yield – up to 50 ln Low follow-up expansion of foamn Physiologically harmless when cured, neutral odourn DIN 4102 Class B2n Acoustic insulation of joints; IFT-tested as per DIN 52210n “Stop and go” – possible to interrupt work for as long as desiredn Regulation of quantity dispensed – bridging over various gap widthsn Point of tool made of hardened steel – longer lifen Precision plastic valve – functionality safeguarded by greatly reduced pressure loss => long shelf life/constant product qualityn Does not age or rot


Systemadvantagesn Contains no CFC’sn High foam yield - up to 35 litresn Easy to apply using finger adaptor or grip systemn Contains no formaldehyde or PCBn No substances harmful to health are released after complete curing, neutral odourn Does not rot or deteriorate with agen DIN 4102 Class B3n Reusable grip

CF-F Filling FoamProductdescription:A high-density polyurethane foam used primarily for filling but also for insulating.

UsesFillingn Breaches in wallsn Stair jointsn Holes left by concrete formsn Pre-cast components

Insulatingn Shower traysn Water pipesn Atticsn Joints around door/window frames

CF-F Filling Foam Package contents Ordering designation Item no.

Fillingfoam 12 CF-F 00369810Comeswithapplicatornozzle,CF-FA1fingeradaptor.

Accessories Package contents Ordering designation Item no.

Sparefingeradaptor 1 CF-FA1 00259766Cleaner 12 CF-R1 00024506

CF-FA1


437www.hilti.co.uk | 0800 886 100


CF-I Insulating Foams Package Ordering Item no. contents designation

Insulatingfoam(60ltrs.) 12 CF-I1750B2 00370889Foamcleaner 12 CFR1 00024506Dispenser 1 CFDS1 00259768

CF-I 750 Insulating FoamsProductdescription:High yield polyurethane foams used primarily for insulating and bonding but also for filling.

Uses:nSealing and insulating of doors and windowsnInsulating and filling around grooves for rising mains, water mains, gas mains and electrical mainsnFilling of prefabricated connection jointsn Completion of thermal and acoustic insulationn Insulating and filling around pipesn Insulating and filling around ventilation ductsn Roofs, heating systems and plumbing installationsn Insulating and filling in cold storesn Back filling of wall cladding and curtain-wall claddingn Back filling for sealants

Specialfeatures:n Foam output is easily controlled, precise application with dispensern Precision valve ensures smooth functioning of cann Pistol grip allows easy working, even overheadn Any number of work breaks can be maden Optimal foam yieldn Durable; ageing and rotting resistantn Invisible fasteningsn Cleaner available for neutralizing uncured foamn Ready to cut after 30 minutes

Environmentalfeatures:n Contains no CFC’s.n Contains no formaldehyde.n Physiologically harmless when cured.n Propellant meets requirements of 1987 Montreal Agreement.

Use:

Package Ordering Item no. contents designationInsulatingfoam(50ltrs.) 144 CF-I750B3 00370891Insulatingfoam(50ltrs.) 48 CF-I750B3 00370890Insulatingfoam(50ltrs.) 12 CF-I750B3 00369800

Box contents Ordering designation Item no.

Contactadhesive(Beige) 25 CA359 00029785Dispenser 1 CB200-P1 00055205

CA 359 Contact Adhesive

CA359

CB200-P1

CA359 Contact AdhesiveUses:n Electrical installations, woodworking, interior finishing and industry

Specialfeatures:n High initial grabn Flexible cure allowing movement between differing materialsn Components can be positioned before cure

9



CM 730-1 EP grout Applications Features

n Grouting of stressed structural elements in concrete, steel, brickwork

n Grouting of wide cracks in horizontal surfacesn Grouting of stanchions, masts, barriers and

anchor boltsn Under grouting / filling beneath baseplates and

machine basesn Filling of inaccessible voidsn Surface reinstatement of horizontal surfacesn Grouting in of bridge bearings, rail tracks

n Two component, pre-measured systemn Mixed in own containern Pourable, self levellingn No finishing requiredn High strength at full cure and at early stagen No shrinkagen No solvents

Designation Contents Item no.

CM730-1 8.000 kg 00306930CM405-1primer 0.500 kg 00306921

CM510-1 repair mortar

n Repair of concrete exposed to chemicals, abrasion, high static or dynamic loads

n Surface repair of vertical and horizontal substrates

n Reinstatement of structural joint edges, plinths, steps

n Surface finish repairs (thin, surface repair)n Adhesive bonding of coping stones, flags, slip

bricks

n Two component, pre-measured system (no mixing errors)

n Mixed in own containern Applied and finished with hand toolsn High strength at full curen Quick strength development permits early

traffickingn Non slump, non dripn Concrete grey colour gives unobtrusive repairn Can be feathered to an edgen No shrinkagen No solvents


CM510-1 10.000 kg 00306924CM405-1primer 0.500 kg 00306921

Stirring paddle for CM 510-1 / CM 730-1Paddle d. (mm) Item no.

∅80(for3jawchuckconnection) 00041215∅110(for3jawchuckconnection) 00041216*Mixingpaddle 00024018*Adaptor 00060459* Use in combination for TE-Y direct connection

CI 060 epoxy crack injectionCI060n Restoring load bearing capacity of cracked

concreten Preventative protection against corrosion of

reinforcementn Sealing of cracks in concrete slabs and floorsn Sealing against gas, moisturen Consolidation of friable rock or stone (may

cause staining)

n Ready to use kitn Non-return valves on adhesive nipples and

connection hosen Both components (resin and hardener)

contained in one cartridgen Low viscosity resin permits deep penetration

of cracksn No power requiredn No drillingn Shrink freen Excellent mechancial properties


CI060crackinjectionkit – 00020131CC412-Ifiller – 00306935adhesive and crack sealing compound

Hilti. Outperform. Outlast.

Hilti (Gt. Britain) Limited | 1 Trafford Wharf Road | Trafford Park | Manchester | M17 1BYFreephone: 0800 886 100 | Freefax: 0800 886 200 | www.hilti.co.uk

Hilti (Fastening Systems) Limited l Unit C4 l North City Business Park l Finglas l Dublin 11CallSave: 1-850-287-387 l Freefax: 1-800-654-600 l www.hilti.ie

3444408 January 2009.

Construction Chemicals

Documents

Transcript of Construction Chemicals