Constant-Speed Propeller Systemsby Derek W Beck

June 2008

You may copy, distribute, display this copyrighted work — and derivative works based upon it — but only if they give credit to Derek W Beck and abide by the other license requirements listed here.

This work and its derivatives may not be sold without permission from Derek W Beck.

You may distribute derivative works only under a license identical to the licenses listed here and only if these licenses are explicitly depicted somewhere on the derivative work.

This document is provided for informational use only. Consult the aircraft manual and appropriate FAA handbooks to double-check all information. © Derek W Beck 2008. Some Rights Reserved. www.derekbeck.com Licensed under

Creative Commons Attribution-Noncommercial-Share Alike License.

Constant Speed Propeller Adjusting propeller pitch

allows for better efficiency (more engine power converted into thrust) in a variety of flight attitudes (climb, cruise, etc)

On the C172RG, the range is 12.0º to 26.5º

Greater pitch demands greater torque from the engine, thus for a given power setting, the result is lower RPM’s

Source: FAA-H-8083-3A Airplane Flying Handbook p. 11-4

Propeller ControlPitch is controlled by the (blue) pitch control lever

Increasing PitchOil is supplied through the propeller piston to a piston head, which is pushed down due to the oil pressure, pushing it against a spring and holding it into a high-pitch position

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Maintaining PitchThe pressure is maintained in the system to hold the pitch on the propeller

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Decreasing PitchOil is allowed to drain from the system, allowing the spring to “win” against the oil, forcing the pitch to high pitch

Spring

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

The Governor

Source: http://flash.aopa.org/asf/engine_prop/swf/flash.cfm?

The Governor – Controlling PitchGovernor controls the oil pressure to the propeller (thus, controlling pitch)

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Control of the GovernorThe propeller control lever tightens a threaded shaft that in turn tightens the speeder spring, which increases resistance against spinning flyweights, which are mechanically connected directly to the engine…

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Speeder Spring

To Prop Lever

Flyweights

Prop Lever Forward Prop Lever Back

Governor UnderspeedWhen engine RPM is slower than the propeller control setting, the speeder spring holds the pilot valve down and oil flows from the propeller…

This is called “underspeed”

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Speeder Spring

To Prop Lever

SpinningFlyweights

Governor On SpeedAs engine RPM increases, the tops of the weights are thrown outward by centrifugal force; the lower legs then pivot up, raising the pilot valve against the force of the speeder spring so no oil can flow to or from the propeller…

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Speeder Spring

To Prop Lever

SpinningFlyweights

Governor OverspeedThe faster the flyweights spin, the further out they are thrown, causing the pilot valve to be raised (against the spring) and allowing more oil to flow to the propeller…

This is called “overspeed”

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Speeder Spring

To Prop Lever

SpinningFlyweights

Putting It All Together

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

On SpeedOn Speed condition results when the RPM is constant. Movement of the cockpit controls have set the speeder springs at the desired RPM. The flyweights have positioned the pilot valves to direct oil to or from the propellers. This, in turn, has positioned the propeller blades at a pitch that absorbs the engine power or RPM selected. When the moment of RPM balance occurs, the force of the flyweights equals the speeder spring load. This positions the pilot valves in the constant RPM position with no oil flowing to or from the propellers. Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

OverspeedAt constant speed, an Overspeed condition results and airspeed increases when the airplane begins a descent or engine power is increased. Since the pitch of the propeller blades is too low to absorb engine power, the engine RPM begins to increase. At the instant this happens, however, the flyweights move out and raise the pilot valves, causing oil to flow to the propeller, increasing the pitch of the blades in both cases. Engine speed then slows to the original RPM setting.

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

UnderspeedIf the airplane begins to climb or engine power is decreased, an Underspeed condition results. Airspeed is reduced and, since the pitch of the propeller blades is too high, the engines begin to slow down. At the instant this happens, the flyweights will droop, causing the pilot valves to move down. Simultaneously, oil flows from the propeller, reducing the pitch of the blades. This automatically increases the speed of the engines to maintain the original RPM setting.

Source: http://www.mccauley.textron.com/prop/prop-tech/pg00intro.html

Other Notes The governor boosts the oil pressure sent to the

propeller by 3 to 6 times (e.g. to 300 PSI) The governor range sets the limit on maintaining a

constant speed propeller Beyond these limits, throttle has a direct control on the

RPM’s Within these limits, the propeller pitch adjusts for any

given throttle setting to maintain the RPM’s In general, maintain propeller setting (RPM) higher

than throttle setting (manifold pressure)

Technical (Backup)

Propeller EfficiencyEfficiency (nu) (1.0 = 100%) is a function of the advanced ratio (J), which is dependent on velocity (V), propeller speed (n), and propeller diameter (D)

Thus, nu = f(V/nD)

Source: http://web.mit.edu/16.unified/www/SPRING/propulsion/UnifiedPropulsion7/UnifiedPropulsion7.htm