CONO/COMP - Mark Williams9”ECONO/COMPHOUSINGSWITHBRACKETS 93000 Complete Econo/Comp Solid Rear . ....
1
44 Mark Williams Enterprises has perfected an economical modular 9” Ford aluminum rear end housing setup that can be used for drag racing and street applications. The key element is the reinforced aluminum housing center module cast from a special grade aerospace alloy with an outstanding tensile strength of 60,000 psi (30% higher than 6061). The modular concept allows a variety of end bells and mounting brackets to suit your particular application. Price wise, the MW Modular stacks up favorably to the considerable re-working needed to make OEM units useable, or even the labor intensive fabricated steel housings. But the most important consideration is that the MW Modular housing is a completely CNC machined assembly and is extremely accurate. There is zero stress from bending and welding typical to sheet metal rears. This assures you of an accurate housing that is properly aligned for optimum internal efficiency. The modular unit is also upgrade-able. If, at a later date a class change requires full floating hubs or the width needs to be changed, the appropriate end bells can be bolted on, eliminating cutting and welding. The newest addition to our modular line is the Econo/Comp 4 link housing (shown at right, recommended for LIGHT DUTY dragster and altered applications). It incorporates mild steel 4 link brackets and spacers along with a tubular lower tie bar. These new components make it easier than ever to convert a MW modular solid mount dragster housing to a 4-link set-up. This Modular rear is intended for lightweight Dragster and Altered applications that are less that 1800# and 800 HP. See part number 97780 page 47 for higher powered applications. 9” ECONO/COMP 92000 Econo/Comp 9” Solid Mount Housing . . . .1976.00 9” center section with 5/16” mounting brackets and standard end bells, symmetrical brake mount pattern., (26” wide for 32 1/8” wheel to wheel width). Call for additional widths and applications 92400 Econo/Comp 9” 4 Link Housing . . . . . . . . .2511.00 With 3/16” mild steel 4 link brackets, tubular tie bar and standard end bells w/ symmetrical brake mount pattern, (4-link centers 17-1/4” ) with a 34” wheel to wheel width). Other widths available. 9” ECONO/COMP HOUSINGS WITH BRACKETS 93000 Complete Econo/Comp Solid Rear . . . . . .5223.00 Lightweight aluminum carrier, 35-spline aluminum spool, lightened standard 8620 gears, MW axles (gun-drilled), bearings, drive studs, MW disc brake kit with drilled rotors, 92000 housing. Assembled weight 133 lbs. 93050 Complete Econo/Comp Solid Rear . . . . . .7418.00 Lightweight aluminum carrier, 35-spline aluminum spool, lightened standard 8620 gears, MW axles (gun-drilled), bearings, drive studs, MW disc brake kit with Carbon/Carbon brakes, 92000 housing. Assembled weight 121 lbs. 93400 Complete Econo/Comp 4 Link Rear . . . . .5985.00 Lightweight aluminum carrier, 35-spline aluminum spool, lightened standard 8620 gears, MW axles (gun-drilled), bearings, drive studs, MW disc brake kit with drilled rotors, 92400 housing. Assembled weight 149 lbs. 93450 Complete Econo/Comp 4 Link Rear . . . . .8200.00 Lightweight aluminum carrier, 35-spline aluminum spool, lightened standard 8620 gears, MW axles (gun-drilled), bearings, drive studs, MW disc brake kit with Carbon/Carbon brakes, 92400 housing. Assembled weight 137 lbs. 9” ECONO/COMP COMPLETE ASSEMBLIES 92400 Econo/Comp 4-Link Housing 93000 Modular 9” Econo/Comp Assembly
Transcript of CONO/COMP - Mark Williams9”ECONO/COMPHOUSINGSWITHBRACKETS 93000 Complete Econo/Comp Solid Rear . ....
44
Mark Williams Enterprises has perfected an economical modular 9” Ford aluminum rearend housing setup that can be used for drag racing and street
applications. The key element is the reinforced aluminum housingcenter module cast from a special grade aerospace alloy with an
outstanding tensile strength of 60,000 psi(30% higher than 6061). Themodular concept allows a varietyof end bells and mounting bracketsto sui t your part icularapplication. Price wise, the MWModular stacks up favorably tothe considerable re-workingneeded to make OEM unitsuseable, or even the laborintensive fabricated steelhousings. But the most importantconsiderat ion is that the MWModular housing is a completely
CNC machined assembly and isextremely accurate.
There is zero stress from bending andwelding typical to sheet metal rears. Thisassures you of an accurate housing that is properly aligned for optimuminternal efficiency. The modular unit is also upgrade-able. If, at a laterdate a class change requires full floating hubs or the width needs to bechanged, the appropriate end bells can be bolted on, eliminating cuttingand welding. The newest addition to our modular line is theEcono/Comp 4 link housing (shown at right, recommended for LIGHTDUTY dragster and altered applications). It incorporates mild steel 4link brackets and spacers along with a tubular lower tie bar. These newcomponents make it easier than ever to convert a MW modular solid mountdragster housing to a 4-link set-up. This Modular rear is intended forlightweight Dragster and Altered applications that are less that 1800# and 800HP. See part number 97780 page 47 for higher powered applications.
9” ECONO/COMP
92000 Econo/Comp 9” Solid Mount Housing . . . .1976.009” center section with 5/16” mounting brackets and standard endbells, symmetrical brake mount pattern., (26” wide for 32 1/8” wheelto wheel width). Call for additional widths and applications
92400 Econo/Comp 9” 4 Link Housing . . . . . . . . .2511.00With 3/16” mild steel 4 link brackets, tubular tie bar and standard endbells w/ symmetrical brake mount pattern, (4-link centers 17-1/4” )with a 34” wheel to wheel width). Other widths available.
9” ECONO/COMP HOUSINGS WITH BRACKETS
93000 Complete Econo/Comp Solid Rear . . . . . .5223.00Lightweight aluminum carrier, 35-spline aluminum spool, lightenedstandard 8620 gears, MW axles (gun-drilled), bearings, drive studs,MW disc brake kit with drilled rotors, 92000 housing. Assembledweight 133 lbs.
93050 Complete Econo/Comp Solid Rear . . . . . .7418.00Lightweight aluminum carrier, 35-spline aluminum spool, lightenedstandard 8620 gears, MW axles (gun-drilled), bearings, drive studs,MW disc brake kit with Carbon/Carbon brakes, 92000 housing.Assembled weight 121 lbs.
93400 Complete Econo/Comp 4 Link Rear . . . . .5985.00Lightweight aluminum carrier, 35-spline aluminum spool, lightenedstandard 8620 gears, MW axles (gun-drilled), bearings, drive studs,MW disc brake kit with drilled rotors, 92400 housing. Assembledweight 149 lbs.
93450 Complete Econo/Comp 4 Link Rear . . . . .8200.00Lightweight aluminum carrier, 35-spline aluminum spool, lightenedstandard 8620 gears, MW axles (gun-drilled), bearings, drive studs,MW disc brake kit with Carbon/Carbon brakes, 92400 housing.Assembled weight 137 lbs.
9” ECONO/COMP COMPLETE ASSEMBLIES
92400 Econo/Comp 4-Link Housing
93000 Modular9” Econo/Comp
Assembly
