Configuração ONT

PROPRIETARY & CONFIDENTIAL

25XX Product Family of ONTsModule 6Marcelo Sena/Pablo Guevara

December 2011

25XX Product Family of ONTs

PROPRIETARY & CONFIDENTIAL 3

General information

• All of the indoor ONT’s use the Broadlight 234x chipset

– 2345 has no voice DSP

– 2348 has integrated voice DSP supporting up to 4 calls.

• Separate binaries for different voice protocol stacks

– SIP

– H.248

• Not all models use the same power supply. Be sure the power supply matches the ONT model. The power requirements range from 1.0A to 2.0A for the indoor residential and small business models.


Serial Numbers

• There are two important serial numbers on these products.

– The product serial number is what Zhone uses to track the product.

– The PON serial number, or FSAN serial number, is what the OLT will see when the ONT ranges.

• Zhone tracks both serial numbers. The product serial number should be used for RMA’s.


Serial number placement

Product S/N

PON S/N

Similar placement on the 2501, 2504, 2510A, 2520


Serial number placement

Product S/N

PON S/N

Similar placement on the 2511, 5114, 5120


Comon Specs

•Interfaces

–GPON: SC/APC Connector

–1.244Gbps Burst Mode Upstream Transmitter (1310nm)

–2.488Gbps Downstream Receiver (1490nm)

•Voice Support

–5 REN per line, balanced Ring at 55V RMS,

–DTMF dialing

–Multiple voice codec - G.711 (u/a-law), G.726,

–G.729 (A and B), G.723.1

–T.30 and T.38 Fax

–Echo Canceling, VAD, CNG

–Various CLASS services - Caller ID, Call Waiting,

–Call Forwarding, Call Transfer, etc.

–SIP (RFC3261), MEGACO v2 (H.248)

•GPON

–Fully ITU-T G.984 compliant framing

–Multiple T-CONTs per device

–Multiple GEM Ports per device

–Support Single T-CONT mode and Multiple

T-CONTs mode

–Flexible mapping between GEM Ports and T-CONT

–Activation with automatic discovered SN and password in conformance with ITU-T G.984.3

–AES-128 Decryption with key generation and switching

–FEC (Forward Error Correction)

–802.1p mapper service profile on U/S

–Mapping of GEM Ports into a T-CONT with priority queues based scheduling

–Support for Multicast GEM Port

•Standards Support

–ITU-T G.984 compliant


Comon Specs – cont.

•Ethernet / IP

–Bridging and switching (802.1D / 802.1 Q)

–Four traffic classes with 802.1p

–802.3n flow control

–Up to 512 MAC address entries

–VLAN tagging / untagging

–VLAN stacking (Q-in-Q)

–MAC limiting

–802.1x Ethernet Authentication

–PPPoE client

•Power

–Input: 110/240V AC Adaptor (12 VDC)

–Power Consumption: 8-12W

–Dying Gasp Support

•Management

–OMCI complies with G.984.4

•IPTV

–IGMP multicast

–IGMP snooping

•Bandwidth/Distance

–Compliant with ITU-T G.984.2 Amd1, Class B+

–APD receiver and DFB transmitter

– -0.5~+5dBm launch power, -27 dBm sensitivity, and -8dBm overload

•Regulatory Compliance

–CE (ETSI)

•Operating Requirements

–Operating Temperature: -5C to 45C

–Operating Humidity: 5% - 90% non condensing

–Storage Temperature: -20C to 60C

–Storage Humidity: 5% - 95% non condensing


2510

•2510A – 4FE + 2POTS

•First version of basic ONT with VoIP support

•This ONT is no longer shipping

•2510A is the direct replacement

•Last software version for 2510 R2.0.9.19A

–Newer code can not be loaded to the 2510


2510A

•2510A – 4FE + 2POTS

•Same interfaces as 2510 ONT

•Improved performance

–The default IP (LAN side) is 192.168.1.1


2511

• 2511 – 4FE + 2POTS + RF

• Uses BL2348 with no external switch chip

• Ships with a fiber tray

– The default IP (LAN side) is 192.168.1.1

225 mm

268 mm

137 mm188 mm


Fiber tray wire management

Three examples of wire management using the detachable fiber tray.


Wire Management

The ONT’s that ship with a fiber tray can also support fiber management without the tray. This figure shows fiber management using the bottom of the ONT.


2543

•Same as 2511

•Smaller form factor

•Same specs

•GE instead of FE ports

•Uses the same software as the 2511


OMCI

• The 25XX ONT series are configured using Operation, Management, and Control Interface (OMCI) which is defined in ITU-T G.983 and G.984.

– The MXK OLT sends configuration down to the ONU

– ONU do not store configuration information. Every boot requires configuration from the OLT

– OMCI only works between OLT and ONU. Does not work over multiple hops.

– OMCI is bidirectional. The ONU reports alarms and statistics to the OLT using OMCI.

• The Management Entity (ME) in OMCI is similar to a MIB in SNMP.

• Zhone calls the file loaded into the MXK the “ME” file because it is made up of our variables and many ME’s.


OMCI Configuration Web Tool

• http://www.zhone.com/support/tools/omci/

• Only the ONT models that have passed testing are listed on this site.


VLAN – GEM – UNI Mapping


MAC Table Size

• All models - 512 total on all models

– 256 used for unicast

– 256 used for multicast


Reg Id

• Ativacao do Reg. ID na ONT

• Conectar o cabo de forca para energizar a ONT.

• Desconectar a interface PON se estiver conectada, conectar um aparelho telefonico na primeira porta POTS da ONT.

• Pressionar o botao de reset da ONT por 5 segundos.

• Esperar ate que o LED POTS da ONT comece a piscar ( 0.7 segundos ligado, e 0.7 segundos desligado).

• Retire o monofone do telefone para fora do gancho.

• Ativar o tom de discar executando as seguintes funcoes:

• * Para ASCII SLID/Password, discar "*0":

• * Para Hexadecimal SLID/Password, discar "*1":

• Esses numeros podem ser modificados em um outro firmware.

• Depois do tom de discar, disque o valor SLID executando um dos seguintes passos:

• * Para ASCII - SLID/Password, discar duas vezes a SLID/Password, suporta ate 10 digitos com "#" finalizando em cada vez. As duas passwords (senhas) dever ser a mesma. Somente digitos de 0 a 9 sao aceitos.

• * Para Hexadecimal, discar duas vezes a senha ate 20 digitos com “#” finalizando em cada vez. As duas senhas devem ser a mesma. Somente digitos 0 to 9 e "*1" ate "*6" sao aceitos. "*1" a "*6" represents "A" to "F".

• Nota: Na versao corrente, as senhas hexadecimais s somente aceitam 30 ~39 (ex:. ASCII de 0 a 9).

• 8. Se o tom de ocupado for ouvido, a SLID/Password nao foi aceita. Coloque o monofone no gancho e volte ao passo 4.

• 9. Se o tom de discar for ouvido, a SlID/Password foi aceita. Coloque o monofone no gancho para sair do modo de provisionamento da SLID/Password.

• 10. Rebote a ONT

• 11. O procedimento foi completado com sucesso e a ONT pode ser inserida na fibra para ocorrer a insercao automatica na ONT designado no item 1) pelo ZMS ou atraves do comando de linha.

• OBS: Para a insercao do REg ID na ONT, e’ necessario que a ONT tenha um firmware que suporte essa funcao.


ONT 25xx Management – Telnet/WebGUI

• User: root

• Password: admin

• - Management

• Web GUI

• CLI

• OMCI


ONT 25xx Management - LAN


ONT 25xx Management - WAN

Configuração ONT

Documents

Transcript of Configuração ONT