CONEXIONES/CONFIGURACIÓN INICIAL (READY TO PLAY ...

Please read these instructions carefully before attempting to connect,operate or adjust this product. Please save this manual.Spanish Quick Use Guide is included.(Guía para rápida consulta en español está incluida.)

LSQT0576B

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Video Cassette RecorderOperating Instructions(Basic Operations)For advanced operations, see the separate“Advanced Operations” instruction book.

Model No. PV-V462

Table of ContentsImportant Safeguards and Precautions .................... 2Before Using ............................................................ 3Connections and Initial Setup (Ready to Play) ......... 4Playback / Record on a Tape ................................... 5Timer Recording ....................................................... 6Location of Controls ............................................. 7, 8Spanish (Español) Quick Use Guide ............ 9, 10, 11Limited Warranty / Customer Services Directory.... 12

As an ENERGY STAR ® Partner,Matsushita Electric Corporation of Americahas determined that this product or productmodel meets the ENERGY STAR ®guidelines for energy efficiency.

• Lim

ited W

arranty • C

ustom

er Services D

irectory • Gu

ía para ráp

ida con

sulta (S

pan

ish Q

uick

Use G

uid

e)

- 12 -

Note

- 11 -

Si no puede resolver su problema, por favor comunicarse al Centro dellamadas del Cliente para asistencia del producto al 1-800-211-PANA(7262).Para localizar un centro de servicios autorizado, llame sin costo al1-800-211-PANA(7262) o envie un correo a : [email protected]

Spanish Quick Use Guide/ Guía para rápida consultaANTES DE AL SERVICIO SOPORTE TÉCNICO

Spanish Quick Use Guide/ Guía para rápida consulta • Gu

ía para ráp

ida con

sulta (S

pan

ish Q

uick

Use G

uid

e) • Location

of Con

trols (Mu

lti Fu

nction

Disp

lay, Rear V

iew of th

e VC

R)

- 10 -

OPERACIONES BÁSICAS PARALA REPRODUCCIÓN

Detalles especiales durante la grabación

Presione FF o REW para búsqueda deescenas hacia delante/ hacia atrás.Presione PLAY para liberar.Luego de que la búsqueda se ha iniciado,cada vez que presione FF o REW secambia la velocidad como sigue:[SLP] aprox. 21X ↔↔↔↔↔ aprox. 9X[LP] aprox. 9X ↔↔↔↔↔ aprox. 7X[SP] aprox. 7X ↔↔↔↔↔ aprox. 3XSi la imágen se interrumpe con la velocidad de21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.

Presione PAUSE/SLOW para imagenFija (Congelada).Presione PLAY para liberar.Presione PAUSE/SLOW en el modode Imagen fija para imágenes cuadro acuadro. Presione PLAY para liberar.Mantenga pulsado PAUSE/SLOW enel modo de imagen fija para imágenesen cámara lenta.Presione PLAY para liberar.

Presione EJECT en el control remoto, oSTOP/EJECT en el VCR para expulsarel cassette.

Presione REW o FF en el modo deparada para rebobinado/avance rápidodel cassette.

Grabación de un toque.Presione REC repetidamente para ajustarla duración de la grabación como sigue:como sigue: 30 min. ➛➛➛➛➛ 1 hr ➛➛➛➛➛ 1:30hr ➛➛➛➛➛2:00 ➛➛➛➛➛ 3:00 ➛➛➛➛➛ 4:00 ➛➛➛➛➛ Salida.La VCR se apagara automáticamente en enintervalo seleccionado de tiempo.

1 Inserte una cassette,• la alimentación del VCR se activa.

En la Pantalla de Visualización MultiFunción se ilumina “VCR”.

2 Presione PLAY para reproducir elcassette.• Si el cassette no tiene lengüeta de

prevención de grabación (p. 3), se inicia lareproducción automáticamente.

3 Presione STOP para detener elcassette.

OPERACIONES BÁSICAS PARALA GRABACIÓN

1 Inserte el cassette con lengüeta deprotección de grabación (p. 3).• La alimentación del VCR se activa.

En la pantalla Multi Función se ilumina“VCR”.

2 Presione CH , o las teclas denúmeros para seleccionar el canal.

3 Presione SPEED para seleccionar lavelocidad de grabación (p. 3)• SP = Reproducción estándar,• LP = Larga duración,• SLP = Superlarga duración.

4 Presione REC para comenzar a grabar.• Para eliminar escenas indeseadas,

presione PAUSE/SLOW para pausar, y alpresionar nuevamente se reanuda lagrabación.

5 Presione STOP para detener lagrabación.

Ver un canal y grabar otro.Presione VCR/TV.(La indicación VCR se apagara en la“visualización de Multi-Función”)➛➛➛➛➛Seleccione canales de TV (Mientras

permanece grabando)Seleccione canales con VCR.Presione VCR/TV (la indicación “VCR” seencenderá en la vizualización multi-función)➛➛➛➛➛Seleccione canales en su VCR.

PROGRAMACIÓN FÁCIL PARALA GRABACIÓN CONTEMPORIZADOR

1

Presione para seleccionar unnúmero que no está usando paraingresar mas programas y presione para ajustar. Luego repita el paso 2.

Presione nuevamentePROG para salir.

Presione PROG para finalizar elprograma.

Fecha de hoy

Orden para elegirEjemplo

2) Para los ajustes siguientes,presione para seleccionar ypresione para ajustar los tiemposde INICIO/PARADA, CANAL, oentrada de LINEA, y velocidad delcassette (SP, LP, SLP).

Presione POWER off para ajustar eltemporizador.(Se ilumina “TIMER” en el panel delantero)

2

3

4

1) Para ajustar la FECHA degrabación, presione paraseleccionar: 1-31 = una vez, o

DIARIO = a la mismahora de lunes a viernes,o SEMANA = a lamisma hora cadasemana y presione para ajustar.

REVISIÓN, REEMPLAZO OBORRADO DE PROGRAMACIONES(no se puede efectuar durante la grabación)

a

b

c

1) Presione PROG.2) Presione para seleccionar la

linea.Presione paraseleccionar programadeseado.

Para reemplazar programa...1) Presione para

desplegar menu.2) Repita paso 2 (ver

arriba) para introducirel nuevo programa.

Para cancelar programas…Presione ADD/DLT

d Presione PROG Para terminarprogramacion.

PARA CANCELAR LA GRABACIÓNCON TEMPORIZADOR(la grabación está teniendo lugar)

Presione POWER y luego STOP dentrode los 10 segundos para cancelar lagrabación con temporizador (el indicadorTIMER se apagará en la Pantalla de Multi-Función)

1) Presione PROG.2) Presione para visualizar la

pantalla de Programación.

DIARIO7

2131 68 9

/ Orden para elegir

SEMANAL(SAB)

SEMANAL(LUN)

SEMANAL(DOM)

FE I N I C PARADA CA VEL7 2 : 00 P 3 : 20 P 02 SLP-- -- : -- -- : -- -- ---- -- : -- -- : -- -- ---- -- : -- -- : -- -- --

CANCELAR: ADD / DLT ELEGIR : FIJAR :SAL I R : PROG

PROG. L I STA

PROG. L I STAFECHA I N I C I O PARADA CA

SLPELEGIR FECHA DE I N I C I O

7 SAB --:-- --:-- --HOY

ELEGIR : FIJAR : TERMINAR : PROG

FE I N I C PARADA CA VEL7 9 : 00 A 12 : 00 A 08 SP8 10 : 00 P 12 : 00 P 02 SP10 8 : 00 P 9 : 00 P 10 SPSU 9 : 00 P 10 : 00 P L1 LP

PROG. L I STA


PROG. L I STAFECHA I N I C I O PARADA CA

SLPELEGIR FECHA DE I N I C I O

7 SAB 9:00A 12:00A 08HOY

ELEGIR : FIJAR : TERMINAR : PROG

FE I N I C PARADA CA VEL-- -- : -- -- : -- -- --8 10 : 00 P 12 : 00 P 02 SP10 8 : 00 P 9 : 00 P 10 SPSU 9 : 00 P 10 : 00 P L1 LP

PROG. L I STA


VCR

VHF/UHF

Estuche convertidor de TV por cable

TelevisorTerminal IN FROM ANT.

Entrada (IN) desdeANT./CABLE

Terminal OUT TO TV

Terminal IN FROM ANT.Televisor

VCR

VHF/UHF

Terminal OUT TO TV

Entrada (IN) desdeANT./CABLE

Spanish Quick Use Guide/ Guía para rápida consulta

- 9 -

CONEXIONES

Conecte el cable de la antena alterminal IN FROM ANT del VCR.Conecte el terminal OUT TO TVdel VCR a la entrada de la antenaVHF/UHF del TV con el cable RFincuido.

Para Ant/Cable ➛➛➛➛➛ VCR ➛➛➛➛➛ TV

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable ➛➛➛➛➛ VCR ➛➛➛➛➛ TVConecte la salida de convertidorde cable al terminal IN FROMANT.Conecte el terminal OUT TO TVdel VCR a la entrada de la antenaVHF/UHF del TV con el cable RFincluido.

1

2

1

2

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.La videograbadora iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

1 Encienda el TV y cambie al canal 3.

2 Enchufe el cable de CA.La videograbadora se encenderá einiciará las fijaciones de los canales ydel reloj.• Si no aparece la pantalla de abajo,

compruebe la conexión del VCR-TV ysi el canal del TV está a 3, intenntecambiando al canal 4.

• Para cambiar el canal de salida delVCR, consulte las instrucciones de“Canal de salida del VCR” en la página12 de las operaciones avanzadas.

Si está usanndo un convertidor de TV porcable y en su area hay un canal de PublicBroadcast Station (PBS), ajuste suconvertidor al canal PBS de su area.Si está usando un receptor DSS, este debeestar apagado.

CONFIGURACIÓN INICIAL

3 Las fijaciones se realizanautomáticamente. Cuando terminallas fijaciones, aparecerá la siguientepantalla.

Si aparece en la pantalla “FIJACIONAUTOMATICA DEL RELOJ ESINCOMPLETO”, Ajuste el reloj comose describe a continuación.

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

1 Presione la tecla ACTION en elcontrol remoto para visualizar lapantalla del menú RELOJ.

2 Presione para seleccionar el mesy para ajustar. De la misma forma,seleccione y ajuste la fecha, año,hora y DST (Hora de Verano).

3 Presione dos veces la tecla ACTIONpara poner el RELOJ en marcha ysalir.

2

1

2

1

CONEXIONES/CONFIGURACIÓN INICIAL (READY TO PLAY)

VCR RELOJ CANAL

FIJACION ES COMPLETO

VERANO : ACT9 /29 / 20 0 2 DOM 2 : 20PM

F I J A R : I N I C I AR : ACT I ON

VCR RELOJ CANAL

ELEGIR MES

VERANO : ACT1 / / :

ELEGIR : FIJAR : SALIR : ACT I ON

Panasonic Consumer Electronics Company,Division of Matsushita Electric Corporation of AmericaOne Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),Division of Matsushita Electric of Puerto Rico, Inc.Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park,Carolina, Puerto Rico 00985

Printed in IndonesiaLSQT0576BS1201-1052

P

Location of Controls

- 8 -

Note to CABLE system installerThis reminder is provided to call the CABLE system installer’s attention to Article 820-40 of theNEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for propergrounding and, in particular, specifies that the cable ground shall be connected to the groundingsystem of the building, as close to the point of cable entry as practical.

ALIMENTACIÓN DE ACLa unidad no enciende….

GRABACIÓN Y REPRODUCCIÓN(REC / PLAY)

No se pueden grabar programas de TV

No se puede efectuar grabación contemporizador…

No hay imagen de reproducción, o laimagen de reproducción tiene ruidoso contiene rayas...

En la reproducción de efectosespeciales, la imagen puede conteneralgunos saltos verticales cuando seutiliza un televisor con Control deBloqueo Vertical Automático...

No se puede controlar el VCR...

Verifique los siguientes puntos una y otra ves si esta teniendo problemas con su VCR.(BO : Haga referencia en la instruciones de funcionamiento [Operaciones Básicas])(AO : Haga referecncia el la instruciones de funcionamiento [Operaciones Avanzadas])

CORRECCIÓN• Revise que el cordon de alimentación de AC este correctamente

conectado a la toma de pared.• Presione el botón “POWER” para el encendido de la unidad.• Verifique que la fuente de alimantación está activada.

Varios

No se pueden ver los programas enel televisor...

No se puede introducir la cassette devídeo...

No se puede extraer la cassette devídeo...

La cassette de vídeo es expulsada aldar comienzo a una grabación o aldesactivar la alimentación para lagrabación con teporizador...

En el modo de Detención, el motor(CILINDRO) sigue girando...

CONTROL REMOTO

NO funciona el control remoto...

Los botones “ACTION” y/o “PROG”no responden...

CORRECCIÓN

• Revise las conexiones entre VCR, antena externa o cable y TV.• Verifique la selección de conexiones (BO p. 4, AO p. 3)• Verifique que su sistema de antenna (Cable o TV) estén

correctamente seleccionados. Vea “Channels” (AO p. 12).• Asegúrese que la pestaña en el cassette de grabación esté

intacta (BO p. 3).

• Compruebe que el reloj ha sido ajustado a la hora y fecha actual.• Asegúrese de que la caja de Cable/DSS (si se utiliza) se

deja encendido y está sintonizado al canal a grabar.• Ajuste las horas de comienzo y deteción de grabación

correctamente. (BO p. 6)• Asegúrese de que ha apagado el VCR antes de la grabación.

(BO p. 6)• La grabación con temporizador quizás no pueda realizarse o

continuarse si se produjera una interrupción de corriente anteso durante una grabación con temporizador, incluso después derestablecido el fluido eléctrico.

• Seleccióne el canal 3 o 4 en el televisor, de modo quecorresponda con el canal de salida del videograbador (3 o 4)(BO p. 4), o seleccione LINE.

• Ajuste el selector VCR/TV a “VCR”.• Ajuste el control TRACKING en una de las dos direcciones. (BO p. 3)• Pruebe a realizar la limpieza de cabezales. (BO p. 3)

• Ponga el Control de Bloqueo Vertical del televisor en“MANUAL” y luego realice el ajuste.

• Asegúrese de que el aparato está encendido.• Revise las pilas del control remoto.• Asegúrese de que el BLOQUEO DEL VCR esté ajustado a

INACTIVO (AO p. 10)• Asegúrese de que no está funcionando una grabación con

temporizador.

CORRECCIÓN• Asegúrese de que el aparato está encendido.• Asegúrese de que el control remoto está en le modo de VCR.• Apunte el control remoto derectamente al sensor remoto del

VCR. (BO p. 7)• Evite que ningún objeto interrumpa la señal del control remoto.• Revise las pilas del control remoto (BO p. 3)• Asegúrese de que el BLOQUEO DEL VCR esté ajustado a

INACTIVO (AO p. 10)• Si ei sensor remoto recive directamente la lus del fluorescente o luz

solar puede causar interferencia con la señal del control remoto.

• Verifique las conexiones entre VCR, cable o antena y TV.• Presione el botón VCR para el modo de “VCR”. (AO p. 2)• Revise las baterias del control remoto. (BO p. 3)

CORRECCIÓN• Asegúrese que la TV este encendida.• Asegúrese que la TV esté conectado a la salida de la VCR

(VCR Out).• Verifique conexiones entre VCR,cable o antena y TV.• Ajuste el selector VCR/TV a “TV”. (BO p. 5)• Asegúrese que la apropiada señal fue seleccionada.

• Inserte el cassette con el lado de la ventana hacia arriba y lapestaña de grabación frente a usted.

• Verifique que no tenga ningún cassette dentro del aparato.

• Inserte o conecte completamente el cable de alimentación deAC a la toma de pared.

• Asegúrese que la pestaña de grabación del cassette esteintacta. (BO p. 3)

• Para activar rápidamente el mecanismo de reproducción, elcilindro sigue rotando durannte 3 minutos. Esto disminuye eltiempo de respuesta desde la parada hasta la reroducción ohasta la el modo de búsqueda en rebobinado.

Enchufe el cable de CA.

PRECAUCIÓNAl usar cables coaxiales RF del tipo “tuerca”,apriételos solamente con los dedos. Un aprieteexcesivo puede dañar los terminales.

Rear View of the VCR

OUTIN 1

OUT TO TVVIDEO

AUDIO IN FROM ANT.

VHF/UHF

R

L

VHF/UHF AntennaInput Terminal

VHF/UHF AntennaOutput Terminal

Video Output Connector

AC Power PlugWhile plugged into an ACoutlet, the VCR consumes3.0 W of electrical power inoff condition.

Audio OutputConnector (L/R)

Audio Input Connector(L/R)

Video Input Connector

Hi-Fi IndicatorLights up when Hi-Fi audio ismonitored in Playback Mode.

VCR IndicatorLights up when theVCR/TV selector isset to VCR.

Power IndicatorLights up when power is on.

Clock/ Status/ Channel/ Speed DisplayDisplays the current time. Briefly displays VCR statuswhen a function button is pressed.Briefly displays the channel number, or “L1” or “L2”when a channel or line input is selected.Briefly displays the recording speed when SPEED ispressed.

Multi Function Display

Timer IndicatorLights up when the VCR is set for a TimerRecording, or when One Touch Recording(OTR) is used.Flashes when a Timer Recording is set, but atape has not been inserted into the VCR.

Cambie el idiomaluego de lafijación inicial(para su ayudavea la página 12de lasoperacionesavanzadas.)

Limited Warranty

Panasonic VHS VCR ProductsLimited Warranty

Limited Warranty CoverageIf your product does not work properly because of a defect in materials or workmanship, PanasonicConsumer Electronics Company or Panasonic Sales Company (collectively referred to as “thewarrantor”) will, for the length of the period indicated on the chart below, which starts with the date oforiginal purchase (“warranty period”), at its option either (a) repair your product with new or refurbishedparts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will bemade by the warrantor.

During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,there will be no charge for parts. You must mail-in your product during the warranty period.If non-rechargeable batteries are included, they are not warranted.This warranty only applies to products purchased and serviced in the United States or Puerto Rico.This warranty is extended only to the original purchaser of a new product which was not sold “as is”.Mail-In ServiceFor assistance in the continental U.S.A. in obtaining repairs please ship the product to:

Panasonic Services CompanyCustomer Servicenter Suite B4900 George McVay DriveMcAllen, TX 78503

For assistance in Puerto Rico call Panasonic Sales Company(787) 750-4300 or fax (787)768-2910When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the originalcarton. Include a letter detailing the complaint and provide a day time phone number where you can bereached.IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BE REQUIREDTO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE,AMOUNT PAID AND PLACE OF PURCHASE.CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCHPROOF OF PURCHASE.

PANASONIC CONSUMER ELECTRONICS COMPANY,DIVISION OF MATSUSHITA ELECTRICCORPORATION OF AMERICAOne Panasonic WaySecaucus, New Jersey 07094

PANASONIC SALES COMPANY,DIVISION OF MATSUSHITAELECTRIC OF PUERTO RICO, INC.,Ave. 65 de Infantería, Km. 9.5San Gabriel Industrial Park,Carolina, Puerto Rico 00985

Limited Warranty Limits And ExclusionsThis warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOTCOVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damageswhich occurred in shipment, or failures which are caused by products not supplied by the warrantor, orfailures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration,faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance,power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercialuse such as hotel, office, restaurant, or other business or rental use of the product, or service by anyoneother than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts ofGod.THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTYCOVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIALDAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACHOF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someoneremove or re-install an installed unit if applicable, travel to and from the servicer, loss of or damage tomedia or images, data or other recorded content. The items listed are not exclusive, but are forillustration only.)ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OFMERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.Some states do not allow the exclusion or limitation of incidental or consequential damages, orlimitations on how long an implied warranty lasts, so the exclusions may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary from state tostate. If a problem with this product develops during or after the warranty period, you may contact yourdealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’sConsumer Affairs Department at the addresses listed for the warrantor.PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOURRESPONSIBILITY.

Customer Services Directory

Web Site: http://www.panasonic.comYou can purchase parts, accessories or locate yournearest servicenter by visiting our Web Site.

For Product Information, Operating Assistance, Literature Request, Dealer Locations,and all Customer Service inquiries please contact:1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.or send e-mail : [email protected]

Service in Puerto RicoMatsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

1-800-332-5368 (Customer Orders Only)Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)(Visa, MasterCard, Discover Card, American Express, Check)

Accessory Purchases:

As of April 2002

Product or Part NameAll components of VCR exceptitem listed belowVideo Tape (in exchange fordefective video tape)

Parts

One (1) Year

Five (5) Days

Labor

Ninety (90) Days

Not Applicable

VCR CLOCK CHANNEL

CH AUTO SET PROCEEDING

CANCEL : STOP

VCR CLOCK CHANNEL

9 /29 / 20 0 2 SUN 2 : 20PMDST : ON

SETT I NG : CH 10

AUTO CLOCK SET COMPLETED

AUTO CLOCK SET ISINCOMPLETE

PLEASE SET CLOCK BYPRESSING ACTION KEY

VCR CLOCK CHANNEL

VCR CLOCK CHANNEL

AUTO CLOCK SET PROCEEDING

CANCEL : STOP

PV-V462 Basic-1 (02-5-14) 2nd.p65 2002/05/14, 10:271

LSQT0576B(Basic Operations) - Front

• Tim

er Record

ing • L

ocation of C

ontrols (R

emote C

ontrol B

utton

s, Fron

t View

of the V

CR

)Location of Controls

*Important: If a remote control button does not work when pressed,press the VCR button on the remote and try the button again.

- 7 -

Timer Recording

1 1) Press PROG*.2) Press to display program screen.

Press PROG to end programming.

2

2) Set remaining items,press to select andpress to set START/ STOP times, CH(channel) orLINE input (p. 9 of “Advanced Operations” book), andtape speed (p. 3).

1) Set record DATE,press to select:1~31= one time,or DAILY= MON~ FRI,or WEEKLY= same timeeach week and press .

3 To Enter More ProgramsPress to select andpress to set an unused program.Then repeat step 2.Or, press PROG to exit.

Timer Recording

ExampleToday

Press to selectdesired program.

4 Press POWER off to set the timer recording. (“TIMER” lights on Multi Function Display.)

(Recording is not in progress)

a 1) Press PROG.2) Press to select LIST.

b

c To Replace program...

d Press PROG to end the programming.

• If you are using a Cable Box, VCR Timer Programming Channel (Step 2 above) mustbe set to the Cable Box output channel and your Cable Box must be manually set tothe desired channel. The Cable Box must be left on.

• If a power interruption occurs while programming the timer, the timer program(s) may becanceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appearson-screen, please re-enter the timer programs.

Important notes when using DSS receiver• When recording programs via DSS receiver, DSS receiver must be left on.• When recording programs via an antenna or cable, DSS receiver must be turned off.

Review, Replace, or Clear Program

1) Press to display.2) Repeat Step 2

(above) to set newprograms.

Press ADD/DLT.

orTo Clear program...

Press POWER and then STOP within 10seconds to cancel the Timer Recording.

(The TIMER indicator goes out on MultiFunction Display.)

Cancel a Timer Recording

(Recording is in progress)

- 6 -

Notes

DAILY7

2131 68 9

SELECT / Selection Order

WEEKLY(SAT)

WEEKLY(MON)

WEEKLY(SUN)

TIMER PROG. L I ST

CANCEL : ADD / DLT SELECT : SET :EXIT : PROG

DT START STOP CH SPD 7 9 : 00A 12 : 00A 08 SP 8 10 : 00P 12 : 00P 02 SP10 8 : 00P 9 : 00P 10 SPSU 9 : 00P 10 : 00P L1 LP

TIMER PROG. LIST

SELECT START DATE

DATE START STOP CH

SPTODAY

7 SUN 9:00A 12:00A 08

SELECT : END : PROG

SET:

TIMER PROG. L I STDT START STOP CH SPD13 2 : 00 P 3 : 20P 02 SLP-- -- : -- -- : -- -- ---- -- : -- -- : -- -- ---- -- : -- -- : -- -- --


SELECT : END : PROG

DATE START STOP CH

SLP

SET:

SELECT START DATE

TODAY13 SAT --:-- --:-- --

TIMER PROG. LIST

TIMER PROG. L I ST


DT START STOP CH SPD-- -- : -- -- : -- -- -- 8 10 : 00P 12 : 00P 02 SP10 8 : 00P 9 : 00P 10 SPSU 9 : 00P 10 : 00P L1 LP

• Con

nection

s • Initial S

etup

• Clock

Set • S

elect Ch

ann

el • Playb

ack • R

ecord • A

uto O

peration

This video recorder, equipped withHQ (High Quality) system, iscompatible with existing VHSequipment. Only use tapes with the

mark. Only tapes tested andinspected for use in 2, 4, 6, and 8hour machines are recommended.


- 5 -

1 Insert a tape with a record tab (p. 3).1 Insert a tape.

Special Features During Play

2 Press CH or NUMBER keysto select the channel.• For “LINE” input, see p. 9 of “Advanced

Operations” book.• If recording from a channel over 100, first

press 100 key then the other 2 digits.

3 Press SPEEDto select record speed (p. 3).

4 Press RECto start recording.• To edit, press PAUSE/SLOW to pause,

and again to resume recording.

5 Press STOP to stop recording.

2 Press PLAY to play tape.• If tape has no rec. tab (p. 3), auto play begins.

One Touch Recording(record in progress)Press REC repeatedly to set length as follows:30 min. ➛ 1 hr. ➛ 1:30 ➛ 2:00 ➛ 3:00➛ 4:00 ➛ exit.The VCR shuts off at the length set.

Record one station, watch anotherPress VCR/TV(“VCR” goes out on Multi Function Display),➛ select channels on TV (recording continues).

Select channels on VCR (in STOP orPAUSE mode)Press VCR/TV(“VCR” lights up on Multi Function Display),➛ select channels on VCR.

Record on a Tape

Forward/Reverse Scene Search➛ Press FF or REW.➛ Press PLAY to release.After search has begun, each additionalpress of FF or REW changes speed asshown below.[SLP] : Approx. 21X ↔ Approx. 9X[LP] : Approx. 9X ↔ Approx. 7X[SP] : Approx. 7X ↔ Approx. 3XIf at 21X, 9X, or 7X speed the picture isinterrupted, change speed to 9X, 7X, or 3X.

Still (Freeze) Picture➛ Press PAUSE/SLOW.➛ Press PLAY to release.

Frame by Frame Picture➛ Press PAUSE/SLOW in Still mode.➛ Press PLAY to release.

Slow Motion Picture➛ Hold down PAUSE/SLOW in Still mode.➛ Press PLAY to release.

• Loose or peeling labelsmay cause tape jam.

• These features work best in SP or SLP mode.• The sound will be muted.• To reduce picture noise, see “Manual

Tracking Control” on p. 3.• After VCR is in Still or Slow mode 3 minutes, it

auto switches to Stop mode to protect the tapeand the video heads.

Press REW or FF in Stop mode toRewind or Fast Forward tape.Press EJECT on remote,or STOP/EJECT on VCR to eject tape.

3 Press STOP to stop tape.

Playback a Tape

• Watching one channel and recordinganother is not possible when using CableBox or DSS Receiver.

• After 5 minutes in Pause mode, VCR stopsto protect the tape and the video heads.

• Picture interruption may occur with some TVs.• FF and REW search speed may vary

depending on current tape position.

Notes

Playback / Record on a Tape

Auto PlayInsert a tape ➛ Power comes on ➛ Play starts if there is no record tab (see p. 3).

Auto RewindPlayFast Forward

Play Auto Eject(Repeat Play must be off)Play ➛ Tape end ➛ Rewind ➛ Tape ejects if there is no record tab

Auto Operation Functions

Notes

Notes

➛ Tape end ➛ Rewind

Connections / Initial Setup (Ready to Play)

Connecting

Connect cable fromAntenna/Cable to VCR’s INFROM ANT. jack.

Connect VCR’s OUT TO TVjack to TV’s ANT. IN jackwith included RF Cableaccessory.

For ANT./Cable ➛➛➛➛➛ VCR ➛➛➛➛➛ TV

For DSS/Cable Box ➛➛➛➛➛ VCR ➛➛➛➛➛ TVConnect your cable box’sOUT jack to the VCR’s INFROM ANT. jack with an RFcable.Connect VCR’s OUT TO TVjack to TV’s ANT. IN jackwith included RF Cableaccessory.

1

2

1

2

Please make all cable or antenna connections before plugging into the ACoutlet.Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.

1 Turn TV on and tune to channel 3.

2 Plug VCR Power Cord into AC walloutlet. VCR comes on and autochannel and clock set starts.

WARNINGOver tightening “Nut type” RF coaxial cablesmay damage jacks. Finger tighten only.

• If screen below does not appear, checkVCR - TV connection and, if TV istuned to channel 3, try switching it tochannel 4.

• To change VCR’s output channel,please refer to “VCR’s Output Channel”in Advanced Operations book (p. 12).

If you use a cable box, turn it on and set itto the Public Broadcasting Station (PBS)channel in your time zone. If you use aDSS receiver, it must be turned off.

Initial Setup (Ready to Play)

VCR CLOCK CHANNEL


CANCEL : STOP

3Settings are made automatically.When setup is done, this screenappears.

VCR CLOCK CHANNEL

9 /29 / 20 0 2 SUN 2 : 20PMDST : ON

SETT I NG : CH 10

AUTO CLOCK SET COMPLETED

If “AUTO CLOCK SET IS INCOMPLETE”appears, manually set clock.See below.

AUTO CLOCK SET ISINCOMPLETE


VCR CLOCK CHANNEL

Manual Clock Set

If Auto Clock Set was incomplete.

1 Press ACTION* on remote to displayCLOCK menu.

VCR CLOCK CHANNEL

SELECT MONTH

DST:ON1 / / :

SELECT : SET : EXIT : ACT I ON

2 Press to select the month and to set. In the same manner, select andset the date, year, time, and DST(Daylight Saving Time).

3 Press ACTION to start clock and exit.

- 4 -

Plugging the AC Power Plug into an AC outlet

VCR CLOCK CHANNEL

SET COMPLETED

DST:ON9 /29 / 20 0 2 SUN 2 : 20PM

START : ACT I ON SET :

IN FROM ANT.TV

VCR

VHF/UHF

OUT TO TV

IN fromANT./CABLE

1

2

IN FROM ANT.TV VCR

VHF/UHF

OUT TO TV

IN fromANT./CABLE

Cable TVConverter Box

12

Before Using • Imp

ortant S

afeguard

s • Accessories • H

ead C

leanin

g • Load

ing B

atteries • Preven

t Tap

e Erasu

re • Sp

ecifications • R

ecord/P

layback

Tim

e

- 3 -

INSTALLATION1 POWER SOURCE CAUTION

Operate only from a power source indicated onthe unit or in this manual. If necessary, haveyour Electric Utility Service Company or VideoProducts Dealer verify the power source in yourhome.

2 POLARIZED OR GROUNDING PLUGAs a safety feature, this Video product comeswith either a polarized power cord plug (oneblade is wider than the other), or a three-wiregrounding type plug.

POLARIZED PLUG CAUTION:This plug will only fit into an outlet one way. If youcannot fully insert the plug, try reversing it. If it stillwill not fit, have an electrician install the proper walloutlet. Do not defeat the safety feature by tamperingwith the plug.GROUNDING PLUG CAUTION:This plug will only fit into a three-hole groundingoutlet. If necessary, have an electrician install theproper outlet. Do not defeat the safety feature bytampering with the plug.3 POWER CORD

Make sure power cords are routed so that theyare not likely to have anything rest on them, rollover them, or be in the way of walking traffic.If an extension cord is used, make sure it alsohas either a polarized or grounded plug and thatthe cords can be securely connected. Frayedcords, damaged plugs, and damaged or crackedwire insulation are hazardous and should bereplaced by a qualified service technician.Overloaded outlets and extension cords are firehazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLESVentilation openings in the cabinet release heatgenerated during operation. If they are blocked,heat build-up inside the unit can cause failuresthat may result in a fire hazard or heat damageto cassettes. For protection, follow these rules:a. Never cover ventilation slots or the unit while

in use, or operate the unit when placed on abed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a bookcase or rack, unless proper ventilation isprovided.

5 AVOID EXTREMELY HOT LOCATIONS ORSUDDEN TEMPERATURE CHANGESDo not place the unit over or near any kind ofheater or radiator, in direct sunlight, inside aclosed vehicle, etc.. Do not move the unitsuddenly between areas of extreme temperaturevariation. If the unit is suddenly moved from acold place to a warm place, moisture maycondense in the unit and on the tape.

6 TO AVOID PERSONAL INJURY• Do not place unsecured

equipment on a slopingsurface.

• Do not place this unit on anysupport that is not firm, level,and adequately strong. Theunit could fall causing seriousinjury to a child or adult anddamage to the unit.

• An appliance and cart combination should bemoved with care. Quick stops, excessive force,and uneven surfaces may cause the applianceand cart combination to overturn.

• Carefully follow all operating instructions anduse the manufacturer's recommendedaccessories when operating this unit orconnecting it to any other equipment.

FOR YOUR SAFETY, READ AND RETAINALL SAFETY AND OPERATINGINSTRUCTIONS. HEED ALL WARNINGS INTHE MANUAL AND ON THE UNIT

USING THE VIDEO UNITIf the unit has been in storage or moved to a new location, referfirst to the INSTALLATION section of these safeguards.1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR

MOISTURE OF ANY KIND.2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected bya qualified service technician before use.

3 DURING AN ELECTRICAL STORMDuring a lightning storm, whether indoors or outdoors, orbefore leaving the unit unused for extended periods of time,disconnect all equipment from the power source as well asthe antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN• Never expose the unit to rain or water. DO NOT

OPERATE if liquid has been spilled into the unit.Immediately unplug the unit, and have it inspected by aservice technician. Fire and shock hazards can result fromelectrical shorts caused by liquid contact inside.

• Never drop or push any object through openings in theunit. Some internal parts carry hazardous voltages andcontact can cause electric shock or fire hazard.

• Avoid placing the unit directly above or below your TV setas this may cause electrical interference. Keep allmagnets away from electronic equipment.

5 USING ACCESSORIESUse only accessories recommended by the manufacturer toavoid risk of fire, shock, or other hazards.

6 CLEANING THE UNITUnplug the unit. Then, use a clean, dry, chemicallyuntreated cloth to gently remove dust or debris. DO NOTUSE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Anysubstance such as wax, adhesive tape, etc. may mar thecabinet surface. Exposure to greasy, humid, or dusty areasmay adversely affect internal parts.

SERVICE1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions,this Video product does not operate properly, do not attemptto open or remove covers, or make any adjustments notdescribed in the manual. Unplug the unit and contact aqualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIREDMake sure the service technician uses only parts specifiedby the manufacturer, or those having the same safetycharacteristics as the original parts. The use of unauthorizedsubstitutes may result in fire, electric shock, or otherhazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETYCHECKAfter any service or repairs to the unit, request the servicetechnician to conduct a thorough safety check as describedin the manufacture’s service literature to ensure that thevideo unit is in safe operating condition.

OUTDOOR ANTENNA INSTALLATION1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to theequipment, be sure the antenna or cable system is groundedso as to provide some protection against built up staticcharges and voltage surges.Section 810 of the NationalElectrical Code, ANSI/NFPA70 (in Canada, part 1 of theCanadian Electrical Code)provides information withrespect to proper groundingof the mast and supportingstructure, grounding of thelead-in wire to an antenna discharge unit, sizeof grounding conductors, location of antenna discharge unit,connection to grounding electrodes and requirements for thegrounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWERLINES OR CIRCUITSAn outside antenna system should be located well awayfrom power lines, electric light or power circuits and where itwill never come into contact with these power sources if itshould happen to fall. When installing an outside antenna,extreme care should be taken to avoid touching power lines,circuits or other power sources as this could be fatal.Because of the hazards involved, antenna installation shouldbe left to a professional.

Important Safeguards and Precautions

GROUND CLAMP

ELECTRICSERVICEEQUIPMENT

ANTENNALEAD INWIRE

ANTENNADISCHARGE UNIT(NEC SECTION 810-20)

GROUNDING CONDUCTORS(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

Safety PrecautionsWarning: To prevent fire or shock hazard, do not expose this equipment to rain or

moisture.CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.Avertissement: Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas

exposer cet appareil à la pluie ou à une humidité excessive.Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche

dans la borne correspondante de la prise et pousser jusqu’au fond.

FCC Warning: Any unauthorized changes or modifications to this equipment would void theuser’s authority to operate.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK)

RISK OF ELECTRIC SHOCKDO NOT OPEN

CAUTION

NO USER-SERVICEABLE PARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulatedvoltage within the unit may have sufficientmagnitude to cause electric shock. Therefore,it is dangerous to make any kind of contactwith any inside part of this unit.This symbol alerts the user that importantliterature concerning the operation andmaintenance of this unit has been included.Therefore, it should be read carefully in orderto avoid any problems.

- 2 -

Remote Control Buttons

Light Tower Universal Remote ControlLIGHT button: When pressed, available buttons light and selected mode button (TV, VCR, or

DSS CABLE) flashes 5 seconds. If no button is pressed, light goes out in 5seconds. Also, hold down a button to confirm the selected mode (mode buttonflashes) in the dark.

EJECT button: Press to eject tape. EJECT is not available during recording.

LIGHT(Illuminates the remote)

EJECT(Ejects tape)

DSS/CABLE mode(Enables DSS/CABLE functions)

POWER(Turns VCR off/on)

VCR/TV(For TV or VCR mode)

ACTION(Displays menu)

VCR (mode)(Enables VCR functions)

PAUSE/SLOW(Displays still, frame by frame,or slow motion picture)

COUNTER RESET(Resets counter to zero)

VOLUME UP/DOWN(Adjusts TV volume)

SAP/Hi-Fi(Selects audio mode for playor record)

TV (mode)(Enables TV functions)

PROGRAM(Displays Timer Program screen)

TAPE POSITION(Locates tape position)

ADD/DELETE(Adds or deletes a channel)

SPEED(Changes tape speed)

RECORD(Records a program, etc.)

DISPLAY(Displays VCR status)

INPUT(For LINE or channel)

PLAY (Plays a tape)/FAST FORWARD/SEARCH(Fast forwards tape/ forwardvisual search)REWIND/SEARCH(Rewinds tape/ reverse visualsearch)STOP (Stops tape)

NUMBER Keys(Selects channel directly)

SEARCH/ ENTER(Sets Search System /TV channel)

COMMERCIAL SKIP/ZERO SEARCH

(Starts Commercial Skip/Zero Search)

CHANNEL UP/DOWNTRACKING/ V-LOCK

(Selects channel/ reducespicture noise during Play and

Slow mode)

PLAY, STOP, REW, and FFfunction as operation keys when menusare displayed.

Remote keys

Front View of the VCR

RECORD

PLAY

Cassette Compartment

POWER

REWIND/SEARCH

CHANNEL UP/DOWNTRACKING/ V-LOCK

RemoteSensor

FASTFORWARD/SEARCH

VideoInputConnector

Audio InputConnector(L/R)

STOP/EJECT

Congratulationson your new purchase! With proper use, thisdependable product will provide years ofenjoyment. Please fill in the information below.(Serial number is on tag on back of VCR.)

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No. PV-V462• Serial No.

RF CoaxialCableVJAS0196

Batteries 2 “AA”Remote ControlLSSQ0342

Accessories

To order accessories, call toll free1-800-332-5368.

Loading the Batteries

Battery replacement caution• Do not mix old and new batteries.• Do not mix alkaline with manganese batteries.

Prevent Accidental Tape Erasure

Record Tab

Screw driver

Cover the holewith cellophanetape.

To record againBreak off the tab toprevent recording.

Only use tapes with the mark in this unit.

Record/Playback Time

2 Hours40 Minutes

SP(Standard Play) 1 Hour 2 Hours

5 Hours20 Minutes2 Hours 4 HoursLP

(Long Play)

3 Hours 6 Hours 8 HoursSLP

(Super Long Play)

Type of Video CassetteTape Speed

Setting T160T120T60

Head Cleaning

Video Head Clog SensorScreen-right appears duringplay if clogging is detected.To remove screen, pressPLAY.• Use “dry” type head

cleaning cassette only.(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.Excessive use of tape can shorten head life.

Old or damaged tapes may clog heads.

V I DEO HEADS MAYNEED CLEAN I NGPLEASE I NSERT HEADCLEAN I NG CASSETTEOR REFER TO MANUAL

END : PLAY

Use soft, dry cloth or dusting attachment of avacuum to remove dust from all cabinet ventholes. You may moisten cloth with nonabrasive,antistatic cleaner/ polisher.Caution:Alcohol and various solvents could damagefinish.

Cleaning the VCR

Power Source: 120 V AC, 60 HzPower Consumption:Power On

Approx. 23 WPower OffApprox. 3.0 W

Video Signal: EIA Standard NTSC colorVideo Recording 4 rotary heads helicalSystem: scanning systemAudio Track: 1 track (Normal)

2 channelHi-Fi Audio Sound

Tuner:Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69CABLE Channels: Midband A ~ I (14 ~ 22)

Superband J ~ W (23 ~ 36)Hyperband AA ~ EEE(37 ~ 64)Lowband A-5 ~ A-1 (95 ~ 99)Special CABLE channel 5A(01)Ultraband 65 ~ 94, 100 ~ 125

OperatingTemperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)Operating Humidity: 10 % ~ 75 %Weight: 2.7 kg (6.0 lbs).Dimensions: 430 (W) x 98 (H) x 242 (D) mm

16-15/16” (W) x 3-7/8” (H) x9-9/16” (D) inch

Specifications

Note: Designs and specifications are subjectto change without notice.

Digital Auto PictureAutomatically controls the video output signal forless noise depending on the tape condition.

Digital Auto TrackingContinuously analyzes the signal and adjusts foroptimum picture quality.

Manual Tracking Control(to reduce picture noise)Use during Playback and Slow Motion mode toreduce picture noise.Press CH (TRACKING) / on the remotecontrol or on the VCR until the picture clears up.To return to Auto Tracking, press POWER off,then on again a few seconds later.

V-Lock Control (to reduce picture jitter)In Still mode, CH (TRACKING) / operate as aV-Lock control.

Features for a Quality Picture

R

R

R

R R

R

R

R

VCR CLOCK CHANNEL

AUTO CLOCK SET PROCEEDING

CANCEL : STOP

PV-V462 Basic-2 (02-5-14) 2nd.p65 2002/05/14, 10:283

LSQT0576B(Basic Operations) - Back

LSQT0577A

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Please read these instructions carefully before attempting to connect,operate or adjust this product. Please save this manual.

Video Cassette RecorderOperating Instructions(Advanced Operations)For Basic operations, see the separate“Basic Operations” instruction book.

Models No. PV-V462

As an ENERGY STAR ® Partner,Matsushita Electric Corporation of Americahas determined that this product or productmodel meets the ENERGY STAR ®guidelines for energy efficiency.

Table of ContentsMulti-Brand Control Feature ..................................... 2Advanced Connections (Cable/DSS) ....................... 3MTS Broadcast ........................................................ 4VHS Hi-Fi Stereo System ......................................... 5Tape Operation .................................................... 6, 7Before Requesting Service ...................................... 8Copying Your Tapes (Dubbing) ................................ 9Special VCR Features ............................................ 10On-Screen Displays (OSD) .................................... 11Reset Language, Channels, Clock, VCR’s Output Channel ... 12

Reset Language, Channels, Clock, VCR’s Output Channel • On

-Screen

Disp

lays (OS

D) • R

eset Lan

guage, C

han

nels, C

lock, V

CR

’s Ou

tpu

t Ch

ann

el • DS

T

Press ACTIONto display MENU.

Language1) Press to select

language item.

For Spanish

For French

For English

Channels

2) Press to select“ANTENNA,” thenpress to setyour antenna system(“TV” or “CABLE.”)

• After Channel AutoSet is finished, AutoClock Set will beperformed.

3) Press to select“AUTO SET,” thenpress .

• If you use CableBox, set it to thePBS channel in yourtime zone.

Clock

2) Press to select“MANUAL,” and press

. (For Auto Clock Set,select “AUTO CLOCKSET.”)

(“TIME ZONE ADJUST”appears only whenauto clock is set.)

3) Press and to select and setthe date, time, andDST (DaylightSaving Time).

4) Press ACTION tostart the Clock andexit this mode.

and press tosubtract or addhour(s) as necessary.

• “TIME ZONEADJUST” returns to“0” if clock is setmanually.

VCR’s Output Channel

After 3 seconds

• To Make Corrections,repeat steps 1) ~ 3).

SELECT : EXIT : ACT I ON

REPEAT PLAY :OFFREMOTE WARNING :ONAUTO SHUT- OFF :OFFIDIOMA/LANGUE : ENGLISHVCR’ S OUTPUT CH :3

VCR CLOCK CHANNEL

SEL. : REGLER: QUITTER : ACT I ON

MAGNETO. HORL. CANALREPRISE LECTURE : NONMESSAGE D’ ERREUR : OUICOUPURE AUTO : NONLANGUAGE/IDIOMA : FRANÇAISCA SORTIE : 3

ELEGIR : FIJAR : SAL I R : ACT I ON

VCR RELOJ CANALREPETICION :INACTAVISO/CONT.REMOTO :ACTAPAGADO AUTOMATICO :INACTLANGUE/LANGUAGE:ESPAÑOLCANAL DE SALIDA :3

VCR CLOCK CHANNEL



VCR CLOCK CHANNEL



2) Press repeatedly.

3) Press ACTION to exit.

1) Press to selectCHANNEL.

1) Press to selectCLOCK.

Time ZoneAdjust

1) Press to selectCLOCK.

(Only when Auto Clockis set.)

2) Press to select“TIME ZONEADJUST”

3) Press ACTION.

Add or Delete a Channel

To add channel:Select channel with NUMBER keys andpress ADD/DLT.

To delete channel:Select channel with CH / or NUMBERkeys and press ADD/DLT.

DST (Daylight Saving Time)

VCR auto adjusts clock for DST.Spring (First Sunday in April)DST:ON ➛ Sets clock ahead one hour.Autumn (Last Sunday in October)DST:ON ➛ Turns clock back one hour.• If your area does not observe Daylight

Saving Time, select DST:OFF.• Keep these time changes in mind when

programming VCR for timer recordings.

1) Press to select“VCR’S OUTPUT CH.”

3) Press ACTION.

2) Press .

- 12 -


ANTENNA : CABLEAUTO SETWEAK SIGNAL DISPLAY : OFF

VCR CLOCK CHANNEL

VCR CLOCK CHANNELANTENNA : CABLEAUTO SETWEAK SIGNAL DISPLAY : OFF


VCR CLOCK CHANNEL


CANCEL : STOP

VCR CLOCK CHANNELAUTO CLOCK SETMANUALTIME ZONE ADJUST : 0


VCR CLOCK CHANNEL

SELECT HOUR

DST:ON9 /29 / 2020 0 2 SUN SUN 2 2 : --PM






VCR CLOCK CHANNEL



VCR CLOCK CHANNEL



VCR CLOCK CHANNEL

IF YOU PRESS ACTION KEY, VCR ’ S OUTPUT CH SWITCHES TO CH 4.

VCR CLOCK CHANNEL

PLEASE TUNE YOUR TV TO CH 4.

CHANNEL 08 ADDED

CHANNEL 08 DELE TED



On-Screen Displays (OSD)

REC 1 2 : 0 0AM0 : 25

CH 02-0 : 1 2 : 3 4

SPSTEREOSAPMONO

VCR Status & Clock Displays

Function & Channel Displays Blank Tape/No Video Signal IndicationsWhen blank tape is detected during play,or the current channel has no signal (withWeak Signal Display feature (p. 10) set toOFF), the TV screen will turn solid blue.

Function Status

Rec Time Remaining(OTR mode only.See p. 5 of BasicOperations book.)

CH 0 8

Current Time Channel

Tape Speed(See p. 3 of BasicOperations book.)

Broadcast AudioBeing Received

When a function buttonis pressed, e.g. PLAY, oryou change channels,a 5 second displayappears.

Counter

To display or removeoverlay at right,➛ press DISPLAY*.

On-Screen Displays (OSD)

These displays will alert you to a missedoperation or provide further instructions.

OSD Caution Page


If you attempt to set or review a TimerRecording and the Clock is not set...

After a Timer Program has been set...

If you press REC on the remotecontrol or VCR, and a cassette isinserted with no record tab...

If you press PLAY, FF, REW, or RECon the remote control or VCR withouta cassette inserted...

CHECK CASSETTERECORD TAB

NO CASSETTE

TURN VCR OFFFOR TIMER RECORDING

If you press POWER or STOP duringa Timer Recording...(visible in VCR mode only)

If you press an invalid key on theremote while in CABLE/DSS mode...

TO CANCEL TIMER RECPRESS POWER THENSTOP KEY

VIDEO HEADS MAYNEED CLEANINGPLEASE INSERT HEADCLEANING CASSETTEOR REFER TO MANUAL

END :PLAY

VCR LOCK ACTIVATED

REMOTE CONTROL IS SETTO CABLE/DSS MODE

USE VCR : VCR KEY

If head cleaning becomes necessarywhile playing back a tape...

If you press a function button otherthan STOP/EJECT or POWER whilethe VCR is in VCR Lock mode...

Warning and Instruction Displays

See page 6 ofBasic Operationsbook






See page 10

See pages 2, 10


- 11 -

Tape Position Display Feature

Special VCR Features • Before R

equ

esting S

ervice • Cop

y You

r Tap

es (Du

bb

ing) • S

pecial V

CR

Featu

res

• “DETECTING TAPEPOSITION” onlyappears the first timea cassette is insertedand it takes severalseconds for correctindication to appear.

• The present tapeposition indication isdisplayed.BEG I N END

To find out the present tape position.Tape position is displayed for VHS-CCassettes type, tapes under 30 minutes, andsome other tapes, but the position is notcorrect.

When set to “ON,” picture is displayedregardless of signal strength.

• ON: Picture is displayed despite signalcondition an may have poor quality.

OFF: Screen turns solid blue when signalis weak or non-existent.

• Selecting ON has no effect on connectedequipment with blue back feature.

Press to selectand display CHANNEL.Press to selectWEAK SIGNALDISPLAY, and press

to set ON or OFF.



VCR CLOCK CHANNEL

The power shuts off at a preset time.

VCR CLOCK CHANNEL



Press to selectAUTO SHUT-OFF.Press repeatedly tochange shut-off time asshown below.

1 Press TAPE POSITIONto detect tape position.

DETECTING TAPE POSITION

2 Press TAPE POSITIONto return to normal screen.

If Multi-brand feature is used (page 2), and thisfeature is set to on, a warning appearswhenever an invalid key is pressed in TV, DSS,or Cable mode.

• If “OFF,” remotewarning will not appearif invalid key is pressed.

VCR CLOCK CHANNEL



Press to selectREMOTE WARNINGand press to set ONor OFF.

Remote Warning ON/OFF Feature

1 Press ACTION to display menu.

2

3 Press ACTION to return to normal screen.

When set to ON, all operations except for timerrecord and tape eject are prohibited. Useful forhouseholds with small children.

VCR LOCK ACT I VATED

VCR LOCK OFF

• VCR Lock cancels in 24 hours if clock is set.

To turn on, hold downREC on the VCR in Stopmode with no tapeinserted for 7 sec.(Please ignore the NOCASSETTE warning.)

To turn off, repeat above.

Auto Shut-Off Feature


2


Weak Signal Display ON/OFF Feature


2


VCR Lock Feature


- 10 -

OFF

2 Hours

4 Hours

6 Hours

• The shut-off countdown will notfunction during Play or Record.

Note

VCR CLOCK CHANNELANTENNA : CABLEAUTO SETWEAK SIGNAL DISPLAY : OFF


Insert pre-recorded tape. Insert blank tape with record tab.

Press REC, then PAUSE/SLOWimmediately to enter REC/PAUSE mode.

Press INPUT* to set VCR Input mode to LINE1for Video Input (Rear) or to LINE2 for VideoInput (Front). (See “Selecting the Input Mode”below.)

Press PLAY to start dubbing.Playing VCR starts playback.

Press PAUSE/SLOW to start dubbing.Recording VCR starts recording.

Press STOP to stop dubbing.

To Monitor Dubbing on Your TV

1 Turn your TV on and tune to theRecording VCR channel (CH3 or CH4).

2 Set the VCR/ TV Selector on theRecording VCR to “VCR.”

• Dubbing tapes protected with CopyGuard will have poor quality results.

Selecting the Input Mode

Method 1:Press INPUT repeatedly.Channel Number ↔↔↔↔↔ LINE1 ↔↔↔↔↔ LINE2

Method 2:Press CH / .Display will change as below.

• “L1” or “L2” lights on Multi-Function Display(about 4 sec.) when LINE1 or LINE2 isselected.

• LINE1: For rear audio/video connection.LINE2: For front audio/video connection.

Press STOP to stop dubbing.

Press PLAY, then PAUSE/SLOWimmediately to enter PLAY/PAUSE mode.

The operation of steps 4 and 5 must be done on both playingand recording VCRs at the same time.

Playing (Source) VCR Recording (Editing) VCR

1

2

3

4

5

Caution : Unauthorized exchanging and/or copying of copyrighted recordings may becopyright infringement.

- 9 -

Note 1 2 3

125LINE1(CABLE)

69(TV)

orLINE2

Copying Your Tapes (Dubbing)Before Requesting Service

PowerNo power…

Recording & Playback

TV program cannot be recorded...

Timer recording cannot beperformed…

There is no playback picture, or theplayback picture is noisy or containsstreaks...

Special effects playback, picture maycontain some vertical jitter when usinga TV with an Automatic Vertical HoldControl...

VCR cannot be controlled...

Check the following points once again if you are having trouble with your VCR.(BO : refers to “Basic Operations” Instruction book.)(AO : refers to “Advanced Operations” Instruction book.)

Correction• Completely insert Power Plug into an AC outlet.• Set POWER button to on.• Make sure power source is active.

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette cannot be removed...

Video cassette ejects when arecording is started or the power isturned off for timer recording...

In Stop mode, the motor (CYLINDER)continues to rotate...

Remote Control

VCR cannot be remote controlled...

ACTION and PROG buttons do notrespond...

If you cannot resolve the problem, please call the Customer Call Center for productassistance at 1-800-211-PANA (7262).To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).or send e-mail to : [email protected]

Correction

• Check connections between VCR, external antenna, andTV.

• Check connections selection. (BO p. 4, AO p. 3)• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [AO p. 12])• Make sure cassette record tab is intact. (BO p. 3)

• Confirm that clock is set to current time and date.• Make sure Cable/DSS box (if used) is left on and tuned to

channel to be recorded.• Set recording start/stop times correctly. (BO p. 6)• Make sure VCR POWER button is pressed off. (BO p. 6)• Timer recording may not be performed or continued if a

power interruption occurs before or during a TimerRecording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output channel(3 or 4) (BO p. 4) or select LINE.

• Set VCR/TV selector to “VCR.”• Adjust TRACKING control in either direction. (BO p. 3)• Try Head Cleaning. (BO p. 3)

• Set TV’s Vertical Hold Control to MANUAL, then adjust.

• Make sure VCR power is on.• Check Remote batteries.• Make sure VCR LOCK is set to off. (AO p. 10)• Make sure Timer Record is not in progress.

Panasonic Consumer Electronics Company,Division of Matsushita Electric Corporation of AmericaOne Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),Division of Matsushita Electric of Puerto Rico, Inc.Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park,Carolina, Puerto Rico 00985

Printed in IndonesiaLSQT0577A

S1201-0

P

Correction• Make sure VCR power is on.• Make sure Remote is in VCR mode.• Aim Remote Control directly at remote sensor on VCR.

(BO p. 7)• Avoid any object blocking signal path.• Check Remote batteries. (BO p. 3)• Make sure VCR LOCK is set to off. (AO p. 10)• Exposing VCR remote sensor to direct fluorescent or

outdoor light may cause signal interference.

• Check connections between VCR, external antenna, andTV.

• Press VCR button for VCR mode. (AO p. 2)• Check Remote batteries. (BO p. 3)

Correction• Make sure TV power is on.• Make sure TV is set to output of VCR.• Check connections between VCR, external antenna, and

TV.• Set VCR/TV selector to “TV.” (BO p. 5)• Make sure proper signal source is selected.

• Insert the cassette with window side up; record tab facingyou.

• Check if a tape is already in the unit.

• Completely insert Power Plug into an AC outlet.

• Make sure cassette record tab is intact. (BO p. 3)

• To enable Quick play mechanism, the cylinder will rotatefor about 3 minutes. This reduces response time fromStop to Play mode and from Play to Rewind Searchmode.

- 8 -

REC

1

2

Front of VCR

(Front Audio L/R Video IN jacksare also provided)

Connect VIDEO OUT jack on Playing VCR to VIDEO IN jack on Recording VCR.To monitor the dubbing, also connect a TV as shown.

Connect AUDIO L/R OUT jacks on Playing VCR to AUDIO L/R IN jacks on Recording VCR.

In place of a Playing VCR, you can use other equipment, such as a Camcorder.Simply connect the unit’s Audio/Video outputs to the Recording VCR.

VCR(HiFi) IN FROM ANT.

OUT TO TV

VIDEO OUT

AUDIO OUT

AUDIO IN

VIDEO IN

TV

VHF/UHF

RLR

LR

LR

VCR(HiFi)

Connection

VIDEO IN 2 L-AUDIO IN2-R

(Rear connection shown.)

If you press an invalid key on theremote while in TV mode...

REMOTE CONTROL IS SETTO TV MODE

USE VCR : VCR KEY

See pages 2, 10

• Tap

e Op

erationTape Operation

VCR fast forwards (skips) over 1~3 minutesof recorded tape.

• Press CM/ZERO repeatedly to changeskip time as shown below.

• No indication appears.

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

Set to playback a recording over and over.

ON : Play repeats attape end or ifunrecorded portionover 30 sec. isdetected.

VCR CLOCK CHANNEL



Press to select REPEAT PLAYand press to set ONor OFF.

To quickly return to a specified tape location.

• Unit will go into FF orREW mode and stop atthe last point theCounter was set to0:00:00.

Press RESETCOUNTER at desiredposition to reset to“0:00:00”.

Press CM/ZERO in Stopmode to start ZEROSEARCH.

Repeat Play


2


Zero Search

1 Press DISPLAY during playto display Counter.

2

3 Continue to record, playback, etc.

4 Press STOP.

5

Commercial Skip

1 Press CM/ZERO in Play mode.

- 7 -


PLAY 1 2 : 0 0AM 0 : 0 0 : 0 0

SP

REW 1 2 : 3 0AM CH 02 0 : 30 : 30

SP

STOP 1 2 : 3 1AM CH 02 0 : 0 0 : 0 0

SP

Tape Operation

To Calculate Index Number

Example 1:To go to rec. 2 from rec. 4, enter 3 and pressREW.

Example 2:To go to rec. 6 from rec. 2, enter 4 and pressFF.

NOTE: indicates start points of each recording.

• If Index Search is started very close to anindex mark, that index mark may not becounted in the search.

Search SystemFor each recording, an invisible index mark is placed on the tape. A program index andinformation are also included for timer recordings. These marks are used to access orscan recordings.

Fig. 1

Fig. 2

Fig. 3

Locates end point of recording for continuity.

Examples of Program End Search.

If searchexceeds a fewseconds inBLANK area.

➛ search continues 7 sec. past end point,➛ tape rewinds to 10 sec. before end point,➛ tape plays to end point and stops.

Upon locating end point,

• If Program End Search is started veryclose to an index mark, that mark may beskipped over.

• To cancel, press PLAY or STOP.

End Point

Press SEARCH* todisplay SEARCH in Stopor Play mode, and thenpress NUMBER keys toselect recordingnumber.

• To calculate number,see below.

Press FF or REW onthe remote to startsearch.

Press FF on the remoteto start PROGRAMEND SEARCH.

Play begins at searchend. To search forwardor back 1 index, pressFF or REW on theremote or VCR whilescreen left is displayed(10 sec.).

61 5 72 3 4

1 753 4 62

Program 2Program 1

the current tape position Press SEARCH button

BLANK

INDEX

FF

Index Search Program End Search

1

2

1 Press SEARCH twice to display SEARCHin Stop or Play mode.

2

End Point

Program 2 or BLANKProgram 1


FF

INDEX

End Point

Program 2Program 1


INDEX

INDEX BLANK BLANK

FF

- 6 -

Note

Notes

• To cancel, pressSTOP or PLAY.

• To cancel, pressSTOP or PLAY.

SEARCH INDEX PROGRAM END

ENTER INDEX NUMBER :1USING 1- 9 KEYS

FORWARD SEARCH :FFREVERSE SEARCH :REWNEXT :SEARCHEXIT :STOP

INDEX SEARCH

FORWARD SEARCH :FFREVERSE SEARCH :REW

SEARCH INDEX PROGRAM END

SEARCH START :FF

EXIT :SEARCH

• MT

S B

roadcast • V

HS

Hi-F

i Stereo S

ystem

VHS Hi-Fi Stereo System

• Arrow indicates selection.

STEREOSAPMONO

H I F I : L / RH I F I : L H I F I : RNORMAL

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected toa stereo TV or an external stereo amp and speakers. (See page 4.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.• Hi-Fi and normal audio playback volume level may differ.

• Refer to “ReceivableBroadcast Types” on page 4.

• Select “HIFI(L/R)” or“HIFI(L)” or “HIFI(R)” tolisten to stereo recordings instereo sound.Select “NORMAL” formonaural sound.

Press SAP/ Hi-Fi repeatedlyto select desired mode.

Press SAP/ Hi-Fi repeatedlyto select desired mode.

Audio Mode for Recording

1 Press SAP/ Hi-Fi to display audio mode.(Display disappears after 5 seconds.)

2

3 Do a recording.See p. 5 of “Basic Operations” Instruction book.

Audio Mode for Playback

1 Start playback.See p. 5 of “Basic Operations” Instruction book.

2 Press SAP/ Hi-Fi to display audio mode.(Display disappears after 5 seconds.)

3

• Arrow indicatesselection.

- 5 -


Notes

MTS Broadcast

MONO broadcastNormal monaural sound broadcast.

SAP broadcastSecondary Audio Program (sub language) broadcast.Select SAP audio mode for the sub language.

MTS Stereo broadcastMulti-channel Television Sound Stereo broadcast.Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, selectMONO audio mode for possibly better results.

MTS Stereo and SAP broadcastMulti-channel Television Sound Stereo (main language)and Secondary Audio Program (sub language)broadcasts are being received simultaneously.Select STEREO or SAP audio mode.

The following are possible audio broadcast types and on-screen displays.The signal being received is indicated with an “ ” mark while the selected audio mode isindicated with an arrow.

To display the broadcast signal being received,➛➛➛➛➛ press DISPLAY*.

Equipped with ®-TV Noise Reduction for trueMTS reproduction. ®-TV Noise Reduction isrequired for good stereo separation and audiofidelity. ® is a registered trademark, and islicensed by ® Technology Licensing.

Make the Audio/Video Connection as shown on page 3.• You can use a TV connected to a Stereo amp and speakers instead of a Stereo TV.

Stereo Amplifier

AUDIO INRL

VCR

RLR

OUT TO TV

VHF/UHF

TV

RL

AUDIO OUT

Connection

Receivable Broadcast Types

- 4 -

STOP 1 2 : 0 0AM CH 02 0 : 0 0 : 0 0

SPSTEREOSAPMONO

STOP 1 2 : 0 0AM CH 02 0 : 0 0 : 0 0

SPSTEREOSAPMONO

STOP 1 2 : 0 0AM CH 02 0 : 0 0 : 0 0

SPSTEREOSAPMONO

STOP 1 2 : 0 0AM CH 02 0 : 0 0 : 0 0

SPSTEREOSAPMONO

Advanced Connections • Mu

lti-Bran

d C

ontrol F

eature • A

dvan

ced C

onn

ections

- 3 -

Multi-Brand Control Feature

- 2 -

The Remote Control can be set to control some TV and Cable Box/DSS functions.

After remote is set up, you can select VCR, TV, or DSS/CABLE for the desired function.Press VCR, or TV, or DSS/CABLE on the remote.(Table below shows available unit buttons for each mode.)

• Not all functions listed may be controllable.• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing

NUMBER keys for channel selection.

➛ hold down TV button,➛ enter code with NUMBER keys.

• Repeat setup after remote battery replacement.• Remote will not control every TV, cable box, or DSS made by the manufacturer listed.

If you get no response, your particular unit cannot be controlled. There are NOadditional codes for the products listed. If your product is not listed, then the remote isnot compatible with that product.

Multi-Brand Control Setup

1 Find your TV and Cable Box/DSS Receiver Brand Code Number from those shown below.

3 Confirm code entry,➛ press POWER to turn your TV on or off.• See table below for controllable functions in each mode.

Using Multi-Brand Control

➛ hold down DSS/CABLE button,➛ enter code with number keys.• If code number is 100 or greater,

➛ press 100 key, then other digits. E.g., press 100 - 0 - 2 for 102.

Setup for Cable or DSS control,

ModeUnit VCR TV

VCR

TV

All VOL UP/DOWNPOWER, INPUT, numberkeys, ENTER, CH UP/DOWN, VOL UP/DOWN

VCR/TV, PLAY, STOP,EJECT, SAP/ Hi-Fi, DISPLAY,FF, REW, PAUSE/SLOW,REC, SPEED, CM/ZERO,COUNTER RESET, TAPEPOSITION

CABLE/ DSS

CABLE/DSS

VOL UP/DOWNPOWER, ENTER, NUMBERkeys (except 100key),CH UP/ DOWN

Notes

Notes

2 Setup for TV control,

Panasonic ....................... 01, 02Quasar ............................ 01, 02RCA ...................................... 03GE ......................................... 03Zenith .................................... 04Magnavox ............................. 05

TV Brand Code NumbersSylvania ................................ 05Sharp .............................. 06, 07Sony ...................................... 08Toshiba ................................. 09Sanyo .................................... 10Fisher .................................... 10

JVC ....................................... 11Hitachi ................................... 12Mitsubishi ........................ 07, 13Samsung ............................... 14Gold Star ................... 15, 16, 17

Cable Box Brand Code NumbersArcher ............................... 05, 06, 01, 44, 63, 91, 126Cabletenna ................................... 01, 44, 63, 91, 126Cableview ................. 63, 44, 42, 30, 52, 04, 124, 126Century ......................................... 51, 44, 59, 75, 126Citizen ...................... 63, 44, 42, 30, 52, 04, 124, 126Curtis .............................................. 08, 09, 61, 53, 87Diamond ....................................... 01, 44, 63, 91, 126Drake ..................................................................... 67Eagle .......................... 13, 22, 58, 62, 20, 40, 26, 107Eastern .......................................................... 28, 130GC Brand ................. 63, 44, 42, 30, 52, 04, 124, 126Gemini ........................................................... 04, 124General Electric ............................................... 57, 01General Instruments .. 01, 02, 03, 04, 34, 55, 83, 106,

65, 67, 68, 115, 117, 118, 124, 91Hamlin .......... 14, 15, 28, 41, 102, 103, 104, 108, 130Hitachi ................................................................... 31Jasco ............................................................. 04, 124Jerrold ....................... 01, 02, 03, 04, 34, 55, 83, 106,

65, 67, 68, 115, 117, 118, 124, 91Macom .................................................................. 31Magnavox ...................................................... 26, 112Matsushita .......................................... 16, 17, 97, 109Movietime ......................... 32, 39, 42, 44, 126, 38, 40NEC .......................................................... 38, 40, 32NOVAVISION ................................. 08, 09, 61, 53, 87NSC .......................................................... 38, 40, 32Oak ........................................................... 46, 11, 129Oak Sigma ............................................... 46, 11, 129Panasonic .......................................... 16, 17, 97, 109Philips ....................... 07, 13, 20, 23, 24, 50, 128, 129Pioneer ............................................................ 05, 06Pulsar ....................... 63, 44, 42, 30, 52, 04, 124, 126

Quest ............................................................... 05, 06Radio Shack ................................. 51, 44, 59, 75, 126RCA ................................................... 16, 17, 97, 109Realistic ........................................ 51, 44, 59, 75, 126Recoton ........................................ 51, 44, 59, 75, 126Regal ............ 14, 15, 28, 41, 102, 103, 104, 108, 130Regency ........................................................ 28, 130Rembrandt ........................ 01, 32, 39, 42, 44, 63, 126Salora .................................................................... 68Samsung ........................................ 05, 32, 40, 42, 06Scientific Atlanta ............................. 08, 09, 61, 53, 87Sheritech ............................................................... 27Signal ............................................................ 26, 112SL Marx ................ 32, 40, 42, 06, 43, 44, 52, 63, 126Sprucer ............................................... 16, 17, 97, 109Standard Components .................. 32, 39, 42, 44, 126Stargate .. 32, 40, 63, 44, 42, 30, 52, 04, 06, 124, 126Sylvania ................................................................. 19Teknika .................................................................. 74Telecaption .................................................... 77, 127Teleview ............................................... 32, 40, 42, 06Texscan ........................................................... 18, 19Tocom ...................................... 33, 34, 01, 42, 66, 91Toshiba ................................................................. 36Uniden Satelite ...................................................... 65Unika ............................................ 01, 44, 63, 91, 126Universal ................................ 42, 43, 44, 52, 63, 126Videoway ............................................ 07, 23, 50, 129Vid Tech ................................................................ 64Vidtek .................................................................... 64Viewstar ..................... 13, 22, 58, 62, 20, 40, 26, 107Zenith ................................................. 07, 23, 50, 129

Toshiba ................................................................. 92Hitachi/ Hughes .................................................... 93Magnavox/ Uniden 1 ............................................. 94Magnavox/ Uniden 2 ............................................. 95

DSS Brand Code NumbersPanasonic ............................................................ 96RCA ..................................................................... 97Sony ............................................................. 98, 105

• Due to changes in infra-red commands used by manufacturers, some brands haveseveral codes. If your unit does not respond to the first code, please try the next one.

• Some TV, Cable Box and DSS Box brands require you to turn on the power manually.

ImportantNotes

If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCRto them to receive higher quality picture and sound.

Connect the VCR’s VIDEO OUT jack to the TV’s VIDEO IN jack.

Connect VCR’s L/R AUDIO OUT jacks to the TV’s L/R AUDIO IN jacks.

Set the VIDEO/TV selector of your TV (Monitor/Receiver) to “VIDEO.”

Audio/Video connection

TV

VCRIN FROM ANT.

OUT TO TV VHF/UHF

VIDEO IN

R

L

AUDIO INLR

VIDEO OUT

AUDIO OUT

R

1

2

3

You CannotYou Can

• record and viewboth scrambledandunscrambledchannels ifadditionalequipment isadded.This connectionrequires: twoconverterboxes, an A/Bswitch, and a 2-way splitter.

• view channelother thanthe oneselected forany type ofrecording.

• do a Timerrecording ofa channelunless youselect it atthe cablebox.

IN

VIDEO

AUDIORL

OUT

IN FROM ANT.

OUT TO TV

AUDIO

IN 1

VHF/UHF

R

L VIDEO

OUT TV

IN 2IN 1

CABLE BOX

OUTINOUT 2OUT 1

2-Way Splitter

CABLE BOX

OUT

A/B Switch

VCR

IN

VHF/UHF

�� Connect With Two Cable Boxes

VCR

IN FROM ANT.

OUT TO TV

AUDIO

IN 1

VHF/UHF

R

L VIDEO

OUT

CABLE BOX

OUTIN

INRL

OUT

TV

VIDEO

AUDIO

VHF/UHF

� � � � � With a Cable Box (VCR Cable Box)

ANT

or

CATV

You CannotYou Can• record

scrambledchannels.

• view any(includingscrambled)channel.

• use VCRRemoteControl toselectchannelswithout usingMulti-brandcontrol feature.

ANT

or

CATV

CONEXIONES/CONFIGURACIÓN INICIAL (READY TO PLAY ...

Documents

Transcript of CONEXIONES/CONFIGURACIÓN INICIAL (READY TO PLAY ...