Conductor rail ULA power supply line selection
2
Conductor rail ULA power supply line selection FZ-SZ-ULA 032018 EN UNILIFT Sp. z o. o., sp. k. www.unilift.pl e-mail: [email protected] 1. Inquiry form 1. Line section 2. Covering flange 3. End feed 4. Current collector with connecting cable 5. Sliding hanger 6. Fixing hanger 7. Towing arm 8. Support arm with girder clips 9. End cap List of items: 1 2 3 4 5 5 6 8 7 9 Device characteristics Conductor rail power supply length: L = m Power supply parameters: AC DC Frequency: f = Hz Voltage: U = V Number of poles: phases + PE Device name Motor data Crane/device 1 Crane/device 2 Crane/device 3 Main lift drive Auxiliary lift drive Bridge drive Trolley drive Other Nominal current I [A] N cos φ N Duty cycle (% ED) Power consumption [kW] Nominal current I [A] N cos φ N Nominal current I [A] N cos φ N Power consumption [kW] Power consumption [kW] Duty cycle (% ED) Duty cycle (% ED)
Transcript of Conductor rail ULA power supply line selection
Conductor rail ULA power supply line selection
FZ
-SZ
-ULA
032018 E
N
UNILIFT Sp. z o. o., sp. k. www.unilift.pl e-mail: [email protected] 1.
Inquiry form
1. Line section
2. Covering flange
3. End feed
4. Current collector with connecting cable
5. Sliding hanger
6. Fixing hanger
7. Towing arm
8. Support arm with girder clips
9. End cap
List of items:
1
2
3 45
5
6
8
7
9
Device characteristics
Conductor rail power supply length: L = m
Power supply parameters: AC DC
Frequency: f = Hz
Voltage: U = V
Number of poles: phases + PE
Device name
Motor data
Crane/device 1 Crane/device 2 Crane/device 3
Main lift drive
Auxiliary lift drive
Bridge drive
Trolley drive
Oth
er
Nom
inal curr
ent
I [
A]
N
cos φ
N
Duty
cycle
(% E
D)
Pow
er
consum
ption
[kW
]
Nom
inal curr
ent
I [
A]
N
cos φ
N
Nom
inal curr
ent
I [
A]
N
cos φ
N
Pow
er
consum
ption
[kW
]
Pow
er
consum
ption
[kW
]
Duty
cycle
(% E
D)
Duty
cycle
(% E
D)
initiator:[email protected];wfState:distributed;wfType:email;workflowId:8dc4f4a9fd60a942a9479fe78ebdc582
Conductor rail ULA power supply line selection
FZ
-SZ
-ULA
032018 E
N
UNILIFT Sp. z o. o., sp. k. www.unilift.pl e-mail: [email protected] 2.
Contact data:
Address:
Company:
Contact person: Office:
Phone number: e-mail:
Date:
Support arm fastening by girder clips to the I-beam: yes Support arm length: L = mm
Examplesof mounting
Fastening on higher shelf:
min. 10
A
B/2
L
Hole Ć11 30
L
Fastening on lower:
min. 10
30
Hole Ć11
L
AB/2
Device localisation: indoor outdoor mixed
Environment: normal high humidity dust
chemically aggressive (description)
o oWorking temperature range: C min. C max.
Acceptable voltage drop:
Current collector speed:
at start (default: 5 %)
in continous (default: 2%)
m/min
Location of power points:
other (description)
at the end of the line
in the middle of the line
