Conducting site surveys for wlan performance and reliability
description
Transcript of Conducting site surveys for wlan performance and reliability
Conducting Site Surveys for WLAN Performance and Reliability
Mike Diss
SE, EMEA, [email protected]
June 16, 2010
2
AirMagnet Overview
• Founded in 2001; based in Sunnyvale, California, USA• Amassed over 8,500 customers – 75 of the Fortune 100
– 25,000+ Product Licenses Sold
• Worldwide support in more than 120 countries• Global footprint of authorized resellers and distributors• Recently acquired by Fluke Networks (Worldwide HQ: Everett,
WA)
AirMagnet is the leader in wireless LAN security, performance and compliance solutions for wireless LANs.
3
WLAN Lifecycle: Best Practice to Cope with Constant Changes in Wireless
• Pre-Deployment Design and Planning
– Design wireless network tailored to environment, user and application needs
• Operational Management– Proactively monitor WiFi, RF,
Voice performance to identify problems before impact
• Security Management– Iron-clad protection with visibility
and defense from all forms of wireless threats
Conducting Site Surveys for WLAN Performance and Reliability
5
History of WLAN Design Goals
• Old Way– Minimum # of Access Points– Maximum Power– 30+ Users per AP– Bandwidth… what Bandwidth…
• New Way– 10 Users per AP– Minimum Power– Lots of Access Points– Network Performance (& Signal Quality) is Paramount
6
Need for Site Surveys
• New Installations– How many APs needed?– Where should they be placed?– How should they be configured?
• Existing Installations– Were the correct number of APs deployed?– Were they deployed in the best location?
• Ongoing Network Optimization– Support for new users– Support for new technology– Support for new applications
7
Site Surveying Phases
1. Preparation
2. Site Survey
3. Analysis
4. Reporting & Sign-off
5. Periodic Site Surveys
8
Phase 1: Preparation Phase
• Preparation checklist – Questions to ask– Do you know all the stakeholders?
– Is wireless access needed for indoors or outdoors or both?
– Are any building blueprints or street maps available?
– Where do you require coverage?
– What type of business is it?
– Is this a new deployment or an add-on to the existing one?
9
Phase 1: Preparation Phase (Continued)
– If adding to an existing wireless network:• Are you unhappy with it? Are users complaining? Or is
your business expanding?
• What equipment have you installed? Where are they installed?
– Think about capacity• How many users require wireless service and what
applications will they use?
• What is the geographical distribution for the users?
• Will they be using applications where they need to roam? What are their throughput requirements?
10
Phase 1: Preparation Phase (Continued)
– Are there any known major non Wi-Fi interfering sources? Do you know their locations?
– Is this a multi-floor deployment?
– What are the security requirements?
– Where are the power and Ethernet drops throughout the facility? Is the customer open to installing new drops?
– What is the anticipated growth for the future?
11
Phase 1: Preparation Phase (for 802.11n)
• Questions to ask for 802.11n networks– Am I deploying an 802.11n Greenfield network or do I
need to support legacy 802.11a/b/g devices?
– Will the 802.11n devices be deployed in the 2.4 GHz or 5 GHz Band? Or do you want the Site Survey product to recommend the choice?
– What type of clients will be connecting to the network?
– Will I deploy 802.11n devices for my Guest Network?
– Do I see coverage overlap from APs that belong to my neighbor? Is that coverage from 802.11n or legacy 802.11a/b/g devices?
12
Phase 2: Site Survey
• Load floor plan maps
– Supported format
– Simple, black and white plans
– Calibrate your floor map scale
• Survey tips and tricks
– Perform a visual inspection of the facility• Can I get everywhere I need to?
– Figure out where you require coverage and where you don’t including areas that obscure results
– Perform survey during “normal” business hours
– Don’t scan unwanted channels• Exterior survey to discover RF channels being used
13
Phase 2: Site Survey• Survey tips and tricks
– Make good judgement on the “Signal Propagation Assessment” value
– “Measurement intervals” accuracy• Auto Logging Data Period• No further than what your Signal Propagation
Assessment is set to
– Take readings on both sides of the wall
– Also take readings along the perimeter of the rooms
– Recommendation: Plan your walking path• Results in more accurate clicking
14
Phase 2: Site Survey• Survey tips and tricks
– Take readings around the outside of your building
– Place your man where you are headed for and then click when you reach that location
– Don’t try and do it all in one go• Enable you to “retract” when necessary
– Switch between auto sampling and click only sampling as you walk around• Auto sampling for straight line walks (i.e. corridors)• Click only for points within a room
– Size of hashing at click points indicates range of Signal Propagation Assessment
15
Phase 2: Site Survey
• Perform your surveys – Passive Surveys
• Collect signal data from all APs & Stations in the area
– Active Surveys• Collect actual performance metrics
(data rate, retries, etc)
• Mandatory for 802.11n deployments
– Iperf Surveys• Collect uplink/downlink performance
statistics
16
RF Spectrum Site Survey• Gather RF Spectrum Data
– Non Wi-Fi devices operate in the same spectrum as Wi-Fi
– Cause interference and severely degrade the overall network performance
– Even more important for time sensitive applications
– Locate interfering devices on floor map
– Preferred method: Collect RF data at the same time as a Wi-Fi Survey
17
Phase 3: Analysis Phase• Visualize Wi-Fi signal
coverage
• Visualize real-world user performance metrics
– Data rates, retries, losses
– Uplink/downlink performance
• Visualize Roaming areas
• Visualize areas that suffer from Channel Interference
18
RF Coverage Analysis
• Visualize Wi-Fi signal coverage at every location
• Locate “dead spots” in your coverage
• Know coverage for your “backup” APs
19
RF Coverage Analysis
• 3D view
– Displays signal strength using height instead of heat map
– Visual representation of where there may be issues (valleys, mountains)
• “Overlap” shows area (in red) where 2 or more APs meet certain conditions– On SSID – good
– On Channel – bad
• Multiview– Bleed from multiple floors
– Bleed from outside to inside
– Between buildings
20
Simulate “What-if” scenarios
• Optional step in the site survey process
• Simulate different scenarios and AP settings to minimize “dead zones” and “interference”
• No need to walk the floor again
• Visualize how simulating a new AP, plugs the “coverage hole”
• Simulate noise in the environment
• Helps determine the optimal AP configuration settings
21
Visualize real-world user performance
• Why do you need this?– Visualize what real users will experience
• AirMagnet Solution– Visualize data rates, packet retries & losses– Accounts for conditions at every location– Obtain uplink/downlink performance metrics
• Critical for 802.11n networks
22
Network Design Validation
• Design validation
– “Certify” if the installed Wireless LAN actually meets the initial design specifications
– Mitigates against troubleshooting ‘tail chasing’
– Critical for specialized applications such as voice and video
23
Design Validation example for voice
Non-green areas indicate regions that do not meet
the design requirement
Green area indicate regions
that meet the design
requirement
24
RF Security
• RF Security – Minimize RF spillage outside
corporate boundary
– Visualize if neighbors or attackers in the parking lot can see your network
– Conduct site survey outside the corporate office boundary
– APs may need re-location, different antennas or configuration changes to minimize leakage
25
Phase 4: Reporting & Sign-off
• Most important output for a Site Survey product or in many cases - the “only output”
• Serve as a map for the current recommendations
• Act as a future reference for surveys and other deployment changes
26
Phase 5: Periodic Site Surveys
• Critical to account for changes in the environment, interference sources, user behaviour, obstacle changes, etc.
– Introduction of a new microwave in the cafeteria
– Introduction of new access points by neighbours
Q & A