COMPONENTS AND INSTALLATIONS – Safety - Cables – Intertek ... · IEC Publ Comments Part 3-21:...

COMPONENTS AND INSTALLATIONS – Safety - Cables – Intertek Semko AB, Kista - 1003 Annex 2A Laboratory accreditation (12) 2015-02-16 2014/9 Flexible Scope Limited to introduce new issues of the standards and amendments within the scope of accreditation Standard designation Methods

National/ SEMKO EN or HD

IEC Publ Comments

Cables for signs and luminous-discharge-tube installations operating from a no-load rated voltage exceeding 1 kV but not exceeding 10 kV

SS-EN 50143:2009 Supersedes EN 50143:1997 + A1:2003

Kablar – Flata PVC-mantlade flexibla kablar

SS-EN 50214:2007

Flat polyvinyl chloride sheathed flexible cables

EN 50214:2006

Insulating, sheathing and covering materials for low-voltage energy cables Part 0: General introduction

SS-EN 50363-0:2011 Supersedes EN 50363-

0:2005

Insulating, sheathing and covering materials for low-voltage energy cables

Part 1: Cross-linked elastomeric insulating compounds

SS-EN 50363-1:2005

Part 2-1: Cross-linked elastomeric sheathing compounds

SS-EN 50363-2-1:2005/ A1:2011

Part 2-2: Cross-linked elastomeric covering compounds

SS-EN 50363-2-2:2005

Part 3: PVC insulating compounds SS-EN 50363-3:2005/A1:2011

Part 4-1: PVC sheathing compounds SS-EN 50363-4-1:2005 Part 4-2: PVC covering compounds SS-EN 50363-4-2:2005 Part 5: Halogen-free, cross-linked insulating compounds

SS-EN 50363-5:2005/A1:2011

Part 6: Halogen-free, cross-linked sheathing compounds

SS-EN 50363-6:2005/A1:2011

Part 7: Halogen-free, thermoplastic insulating compounds

SS-EN 50363-7:2005

Part 8: Halogen-free, thermoplastic sheathing compounds

SS-EN 50363-8:2005/A1:2011

Part 9-1: Miscellaneous insulating compounds –Cross-linked polyvinyl chloride (XLPVC)

SS-EN 50363-9-1:2005



IEC Publ Comments

Part 10-1: Miscellaneous sheathing compounds –Cross-linked polyvinyl chloride (XLPVC)

SS-EN 50363-10-1:2005

Part 10-2: Miscellaneous insulating compounds –Thermoplastic polyurethane

SS-EN 50363-10-2:2005

Electrical test methods for low voltage energy cables

SS-EN 50395:2006 SS-EN 50395:2006/A1:2011

Excluding § 10.2

Non electrical test methods for low voltage energy cables

SS-EN 50396:2006 SS-EN 30596:2006/A1:2011

Test methods for analysis of lead in PVC

SS-EN 50514:2009 EN 50514:2008

Method B

Recommended test method for assessment of plasticizer exudation from PVC-insulated PVC insulated and sheathed cables

SS-EN 50497:2008 EN 50497:2007

Electric cables - Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) -

Part 1: General requirements SS-EN 50525-1:2011 Part 2-11: Cables for general applications - Flexible cables with thermoplastic PVC insulation

SS-EN 50525-2-11:2011

Part 2-12: Cables for general applications - Cables with thermoplastic PVC insulation for extensible leads

SS-EN 50525-2-12:2011

Part 2-21: Cables for general applications - Flexible cables with crosslinked elastomeric insulation

SS-EN 50525-2-21:2011

Part 2-22: Cables for general applications - High flexibility braided cables with crosslinked elastomeric insulation

SS-EN 50525-2-22:2011



IEC Publ Comments

Part 2-31: Cables for general applications - Single core non-sheathed cables with thermoplastic PVC insulation

SS-EN 50525-2-31:2011

Part 2-41: Cables for general applications - Single core cables with crosslinked silicone rubber insulation

SS-EN 50525-2-41:2011

Part 2-42: Cables for general applications - Single core non-sheathed cables with crosslinked EVA insulation

SS-EN 50525-2-42:2011

Part 2-51: Cables for general applications - Oil resistant control cables with thermoplastic PVC insulation

SS-EN 50525-2-51:2011

Part 2-71: Cables for general applications - Flat tinsel cables (cords) with thermoplastic PVC insulation

SS-EN 50525-2-71:2011

Part 2-72: Cables for general applications - Flat divisible cables (cords) with thermoplastic PVC insulation

SS-EN 50525-2-72:2011

Part 2-81: Cables for general applications - Cables with crosslinked elastomeric covering for arc welding

SS-EN 50525-2-81:2011

Part 2-82: Cables for general applications - Cables with crosslinked elastomeric insulation for decorative chains

SS-EN 50525-2-82:2011

Part 2-83: Cables for general applications - Multicore cables with crosslinked silicone rubber insulation

SS-EN 50525-2-83:2011

Part 3-11: Cables with special fire performance - Flexible cables with halogen-free thermoplastic insulation, and low emission of smoke

SS-EN 50525-3-11:2011



IEC Publ Comments

Part 3-21: Cables with special fire performance - Flexible cables with halogen-free crosslinked insulation, and low emission of smoke

SS-EN 50525-3-21:2011

Part 3-31: Cables with special fire performance - Single core non-sheathed cables with halogen-free thermoplastic insulation, and low emission of smoke

SS-EN 50525-3-31:2011

Part 3-41: Cables with special fire performance - Single core non-sheathed cables with halogen-free crosslinked insulation, and low emission of smoke

SS-EN 50525-3-41:2011

Cables - Common test methods for insulating and sheathing materials of electric cables

Part 1-1: Measurement of thickness and overall dimensions-Tests for determining the mechanical properties.

SS-EN 60811-1-1:1997/A1:2001 EN 60811-1-1:1995/A1:2001

IEC 60811-1-1:1993 / A1:2001

Part 1-2: Thermal ageing methods SS-EN 60811-1-2:1997/A2:2001 EN 60811-1-2:1985/A2:2000

IEC 60811-1-2:1985 / A2:2000

Part 1-3: Methods for determining the density-Water absorption test-Shrinkage test

SS-EN 60811-1-3:1997/A1:2001 EN 60811-1-3:1995/A1:2001

IEC 60811-1-3:1993 / A1:2001

Part 1-4:Test at low temperature SS-EN 60811-1-4:1997/A2:2001 EN 60811-1-4:1995/A2:2001

IEC 60811-1-4:1985 / A2:2001

Part 2-1: Ozone resistance, hot set and mineral oil immersion tests

SS-EN 60811-2-1:1999/A1:2001 EN 60811-2-1:1998/A1:2001

IEC 60811-2-1:1998 / A1:2001



IEC Publ Comments

Part 3-1: Methods specific to PVC compounds – Pressure test at high temperature – Tests for resistance to cracking

SS-EN 60811-3-1:1997/A2:2001 EN 60811-3-1:1995/A2:2001

IEC 60811-3-1:1998/A2:2001

Part 3-2: Methods specific to PVC compounds – Loss of mass test – Thermal stability test

SS-EN 60811-3-2:1997 EN 60811-3-2:1995

IEC 60811-3-2:1985

Part 4-1: Methods specific to polyethylene and polypropylene compounds – Resistance to environmental stress cracking – Wrapping test after thermal ageing in air – Measurement of the melt flow index – Carbon black and/or mineral content measurement in polyethylene

SS-EN 60811-4-1:1997 EN 60811-4-1:1995

IEC 60811-4-1:1985 / A2:1993

Part 4-2: Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature – Wrapping test after conditioning at elevated temperature - Wrapping test after thermal ageing in air – Measurement of mass increase – Long term stability test – Test method for copper-catalyzed oxidative degradation

SS-EN 60811-4-2:2004 IEC 60811-4-2:2004

Part 201: Measurement of insulation thickness

SS EN 60811-201:2012 IEC 60811-201:2012

Part 202: Measurement of thickness of non-metallic sheath

SS EN 60811-202:2012 IEC 60811-202:2012

Part 203: Measurement of overall dimensions

SS EN 60811-203:2012 IEC 60811-203:2012

Part 401: Thermal ageing methods. Ageing in an air oven

SS EN 60811-401:2012 IEC 60811-401:2012

Part 402: Water absorption tests SS EN 60811-402:2012 IEC 60811-402:2012

Part 403: Ozone resistance test on cross-linked compounds

SS EN 60811-403:2012 IEC 60811-403:2012



IEC Publ Comments

Part 404: Mineral oil immersion tests for sheaths

SS EN 60811-404:2012 IEC 60811-404:2012

Part 405: Thermal stability test for PVC insulations and PVC sheaths

SS EN 60811-405:2012 IEC 60811-405:2012

Part 406: Resistance to stress cracking of polyethylene and polypropylene compounds

SS EN 60811-406:2012 IEC 60811-406:2012

Part 407: Measurement of mass increase of polyethylene and polypropylene compounds

SS EN 60811-407:2012 IEC 60811-407:2012

Part 408: Long-term stability test of polyethylene and polypropylene compounds

SS EN 60811-408:2012 IEC 60811-408:2012

Part 409: Loss of mass test for thermoplastic insulations and sheaths

SS EN 60811-409:2012 IEC 60811-409:2012

Part 410: Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors

SS EN 60811-410:2012 IEC 60811-410:2012

Part 411: Miscellaneous tests – Low-temperature brittleness of filling compounds

SS EN 60811-411:2012 IEC 60811-411:2012

Part 412: Thermal ageing methods - Ageing in an air bomb

SS EN 60811-412:2012 IEC 60811-412:2012

Part 501: Tests for determining the mechanical properties of insulating and sheathing compounds

SS EN 60811-501:2012 IEC 60811-501:2012

Part 502: Shrinkage test for insulations

SS EN 60811-502:2012 IEC 60811-502:2012

Part 503: Shrinkage test for sheaths SS EN 60811-503:2012 IEC 60811-503:2012

Part 504: Bending tests at low temperature for insulation and sheaths

SS EN 60811-504:2012 IEC 60811-504:2012

Part 505: Elongation at low temperature for insulations and sheaths

SS EN 60811-505:2012 IEC 60811-505:2012



IEC Publ Comments

Part 506: Impact test at low temperature for insulations and sheaths

SS EN 60811-506:2012 IEC 60811-506:2012

Part 507: Hot set test for cross-linked materials

SS EN 60811-507:2012 IEC 60811-507:2012

Part 508: Pressure test at high temperature for insulation and sheaths

SS EN 60811-508:2012 IEC 60811-508:2012

Part 509: Test for resistance of insulations and sheaths to cracking (heat shock test)

SS EN 60811-509:2012 IEC 60811-509:2012

Part 510: Methods specific to polyethylene and polypropylene compounds – Wrapping test after thermal ageing in air

SS EN 60811-510:2012 IEC 60811-510:2012

Part 511: Measurement of the melt flow index of polyethylene compounds

SS EN 60811-511:2012 IEC 60811-511:2012

Part 512: Methods specific to polyethylene and polypropylene compounds - Tensile strength and elongation at break after conditioning at elevated temperature

SS EN 60811-512:2012 IEC 60811-512:2012

Part 513: Methods specific to polyethylene and polypropylene compounds – Wrapping test after conditioning

SS EN 60811-513:2012 IEC 60811-513:2012

Part 605: Measurement of carbon black and/or mineral filler in polyethylene compounds

SS EN 60811-605:2012 IEC 60811-605:2012

Part 606: Methods for determining the density

SS EN 60811-606:2012 IEC 60811-606:2012

Part 607: Test for the assessment of carbon black dispersion in polyethylene and polypropylene

SS EN 60811-607:2012 IEC 60811-607:2012

Cables for portable earthing and short-circuiting equipment

SS-EN 61138:2008 EN 61138:2007

IEC 61138:2007



IEC Publ Comments

House wiring cables- Rubber insulated cables with rated voltage up to and including 450/750 V

Part 1: General requirements SS-EN 50525-1:2011 Part 2: Test methods SS-EN 50395/A1:2011

SS-EN 50395:2006 EN 50395:2005

Part 3: Heat resistant silicone rubber insulated cables

SS-EN 50525-2-41:2011

Part 4: Cords and flexible cables SS-EN 50525-2-21:2011 Part 6: Arc welding cables SS-EN 50525-2-81:2011 Part 7: Cables with increased heat resistance for internal wiring for a conductor temperature of 110°C

SS-EN 50525-2-42:2011

Part 8: Polychloroprene or equivalent synthetic elastomer sheathed cable for decorative chains

SS-EN 50525-2-82:2011

Part 9: Single core halogen-free non-sheathed cables for fixed wiring having low emission of smoke

SS-EN 50525-3-41:2011

Part 10: EPR insulated and polyurethane sheathed flexible cables

SS-EN 50525-2-21:2011

Part 11: EVA cords and flexible cables SS-EN 50525-2-21:2011 Part 12: Heat resistant EPR cords and flexible cables

SS-EN 50525-2-21:2011

Part 13: Halogen-free flexible cables having low emission of smoke

SS-EN 50525-2-21:2011

Part 14: Cords for applications requiring high flexibility

SS-EN 50525-2-22:2011

Part 15: Multicore cables insulated and sheathed with heat resistant silicone rubber

SS-EN 50525-2-83:2011

Part 16: Water resistant polychloroprene or equivalent synthetic elastomer sheathed cables

SS-EN 50525-2-21:2011



IEC Publ Comments

Rubber insulated cables of rated voltage up to and including 450/750V.

Part 1: General requirements IEC 60245-1:2008 Part 2: Test methods IEC 60245-2:2008 Part 3: Heat resistant silicone insulated cables

IEC 60245-3:1994 A1: 1997/A2: 2011

Part 4: Cords and flexible cables IEC 60245-4:1994 A1:1997/A2:2003

IEC 60245-4:2011 Part 5. Lift cables IEC 60245-5:1994

A1: 2003

Part 6: Arc welding cables IEC 60245-6:1994 A1:1997/A2:2003

Part 7: Heat resistant ethylene-vinyl acetate rubber insulated cables

IEC 60245-7:1994 A1:1997

Part 8: Cords for applications requiring high flexibility

IEC 60245-8:1998 A1:2003/A2:2011

House wiring cables- PVC-insulated cables type with rated voltage up to and including 450/750 V

Part 1: General requirements SS-EN 50525-1:2011 Part 2: Test methods SS-EN 50395/A1:2011

SS-EN 50395:2006 EN 50395:2005

Part 3: Non-sheathed cables for fixed wiring

SS-EN 50525-2-31:2011

Part 4: Sheathed cables for fixed wiring

Withdrawn once EN 50525 series is ratified

Part 5: Flexible cables (cords) SS-EN 50525-2-11:2011 SS-EN 50525-2-71:2011

Part 7: Single core non-sheathed cables for internal wiring for a conductor temperature of 90°C

SS-EN 50525-2-31:2011



IEC Publ Comments

Part 8: Single core non-sheathed cables for decorative chains


Part 9: Single core non sheathed cable for installation at low temperatures


Part 10: Extensible leads SS-EN 50525-2-12:2011 Part 11: Cables for luminaries SS-EN 50525-2-72:2011 Part 12: Heat-resistant flexible cables (cords)

SS-EN 50525-2-11:2011

Part 13: Oil resistant PVC sheathed cables with two or more conductors

SS-EN 50525-2-51:2011

Part 14: Flexible cables (cords), insulated and sheated with halogen-free thermoplastic compounds

SS-EN 50525-3-11:2011

Part 15: Single core cables, insulated with halogen-free thermoplastic compound, for fixed wiring

SS-EN 50525-3-31:2011

Polyvinyl chloride insulated cables of rated voltage up to and including 450/750V

Part 1: General requirements IEC 60227-1:2007 Part 2: Test methods IEC 60227-2:1997

A1:2003

Part 3: Non-sheathed cables for fixed wiring

IEC 60227-3:1993 A1:1997

Part 4: Sheathed cables for fixed wiring

IEC 60227-4:1992 A1:1997

Part 5: Flexible cables (cords) IEC 60227-5:1997 A1:1997 / A2:2003

IEC 60227-5:2011 Part 6: Lift cables and cables for flexible connections

IEC 60227-6:2001

Part 7: Flexible cables screened and unscreened with tow or more conductors

IEC 60227-7:1995 A1:2003 /A2:2011

House wiring cables-



IEC Publ Comments

PVC-insulated cable rated voltage 450/750 V. Special test method for presence of load

SS 424 02 19-1 1 ed. 1998

PVC-insulated, Al-and PVC-sheated cable. Type EKRK with rated voltage 300/500V

SS 424 02 19-2 1 ed. 1998

PVC-insulated, PVC-sheated cables. Type EKK and FKK with rated voltage 300/500V

SS 424 02 19-3 1 ed. 1998

PVC-insulated, Al-and PVC-sheated cable. Type EKK and FKK with rated voltage 300/500V

SS 424 02 19-4 1 ed. 1998

Polyolefin insulated with rated voltage 300/500V. Cables with special properties in event of fire

SS 424 02 19-5 1 ed. 2004

Polyolefin insulated with rated voltage 450/750V. Cables with special properties in event of fire

SS 424 02 19-6 1 ed. 2008

PVC-insulated, PVC-sheathed extra flexible cable type RKFK with copper braid and with rated voltage 450/750 V

SS 424 02 44 2 ed. 1995

Fluorplastic insulated single core cable without sheath

SS 424 02 46 4 ed. 1995

Single conductor cable for luminaires with tubular discharge lamps of non-preheated types supplied by high frequency voltage

SS 424 02 69 1 ed. 1990

PVC-insulated steelwire, type JK, for heating of concrete

SS 424 03 05 1 ed. 1985

Multicore and multipair cables for installations above and below ground- Designs and tests

SS 424 03 21 3 ed. 2006 (HD 627 + A2 part 1 and HD 627 part 1 4C-1 and 2)



IEC Publ Comments

Power cables of rated voltage 0,6/1 kV- Specifications for design and testing

SS 424 14 18 4 ed. 2007 (HD 603-3-L and HD 603-5-O, -P and HD 604-3-D)

Power cables- Test methods SS 424 14 19 4 ed. 2002 (HD 605 S1 A1 A2 and A3)

SS 424 14 19 5 ed. 2009 (HD 605 S2:2008)

Only clauses 2.1.1, 2.1.2, 2.1.3, 2.1.11, 2.2.8.5, 2.4.1.1, 2.4.8, 2.5.4, 3.1.1, 3.2.1, 3.2.3, 3.3.1, 3.4.1 and 3.4.2

Cables- Testing of fire characteristics SS 424 14 75 6 ed. 2001

IEC 60332-1: 1993 IEC 60332-3: 1992

Not class F4 (IEC 332-3:1992)

Power cables and house wiring cables- Marking of cores and sheath

SS 424 17 20 5 ed. 2001 (HD 186 and HD 308)

Heating cables with rated voltage up to and including 300/500 V- Design and testing

SS 424 24 11 3 ed. 1992

Latest changes are printed in extra bold type. The accreditation does not cover sampling activities. If the laboratory, regardless of this, performs the sampling by itself, then the testing is not considered to be performed under accreditation. Provtagning omfattas inte av ackrediteringen. Om laboratoriet ändå själv utför provtagning omfattas provningen inte av ackrediteringen. The accreditation does not cover opinions and interpretations. If the laboratory, regardless of this, expresses opinions and/or provides interpretations in the test report, then the testing is not considered to be performed under accreditation. Synpunkter och tolkningar omfattas inte av ackrediteringen. Om laboratoriet ändå redovisar synpunkter och tolkningar i provningsrapporten, omfattas provningen inte av ackrediteringen.

COMPONENTS AND INSTALLATIONS – Safety - Cables – Intertek ... · IEC Publ Comments Part 3-21:...

Documents

Transcript of COMPONENTS AND INSTALLATIONS – Safety - Cables – Intertek ... · IEC Publ Comments Part 3-21:...