comp a

download comp a

of 14

Transcript of comp a

  • 7/25/2019 comp a

    1/14

    Jotamastic 87 Comp A

    Not available.

    Liquid.

    1-800-424-9300(Staffed 24/7)

    SAFETY DATA SHEET

    GHS product identifier

    Other means of

    identification

    Product type

    Emergency telephone

    number (with hours of

    operation)

    Section 1. Identification:

    :

    :

    :

    Supplier's details : Jotun Paints, Inc.9203 Highway 23Belle Chasse, LA 70037Telephone: (800) 229-3538 or+1 [email protected]

    Relevant identified uses of the substance or mixture and uses advised against

    Uses in Coatings - Industrial useUses in Coatings - Professional use

    Identified uses

    Jotamastic 87 Comp A

    Product code : 515

    Product description : Paint.

    515;519;527;1549 1,2 515

    epoxy mastic ^(ValidationDate). 1Coatings: Solvent-borne.

    Approved

    Section 2. Hazards identification

    FLAMMABLE LIQUIDS - Category 3SKIN CORROSION/IRRITATION - Category 2SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 1SKIN SENSITIZATION - Category 1SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2

    AQUATIC HAZARD (LONG-TERM) - Category 3

    Classification of the

    substance or mixture

    :

    Signal word : Danger.

    Hazard statements : Flammable liquid and vapor.Causes serious eye damage.

    Causes skin irritation.May cause an allergic skin reaction.May cause damage to organs through prolonged or repeated exposure.Harmful to aquatic life with long lasting effects.

    Hazard pictograms :

    Precautionary statements

    GHS label elements

    OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard(29 CFR 1910.1200).

    Date of issue : 22.10.2015. 1/14

  • 7/25/2019 comp a

    2/14

    Jotamastic 87 Comp A

    Section 2. Hazards identificationPrevention : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot

    surfaces, sparks, open flames and other ignition sources. No smoking. Use explosion-proof electrical, ventilating, lighting and all material-handling equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Keep containertightly closed. Avoid release to the environment. Do not breathe vapor or spray. Washhands thoroughly after handling. Contaminated work clothing should not be allowed out

    of the workplace.

    Response : Get medical attention if you feel unwell. IF ON SKIN (or hair): Take off immediately allcontaminated clothing. Rinse skin with water or shower. IF ON SKIN: Wash withplenty of soap and water. Take off contaminated clothing. If skin irritation or rashoccurs: Get medical attention. IF IN EYES: Rinse cautiously with water for severalminutes. Remove contact lenses, if present and easy to do. Continue rinsing.Immediately call a POISON CENTER or physician.

    Storage : Store in a well-ventilated place. Keep cool.

    Disposal : Dispose of contents and container in accordance with all local, regional, national andinternational regulations.

    Hazards not otherwise

    classified

    : None known.

    Section 3. Composition/information on ingredients

    epoxy resin (MW 700) 10 -

  • 7/25/2019 comp a

    3/14

    Jotamastic 87 Comp A

    Section 4. First aid measures

    Get medical attention immediately. Call a poison center or physician. Wash out mouthwith water. Remove dentures if any. Remove victim to fresh air and keep at rest in aposition comfortable for breathing. If material has been swallowed and the exposedperson is conscious, give small quantities of water to drink. Stop if the exposed personfeels sick as vomiting may be dangerous. Do not induce vomiting unless directed to doso by medical personnel. If vomiting occurs, the head should be kept low so that vomitdoes not enter the lungs. Chemical burns must be treated promptly by a physician.Never give anything by mouth to an unconscious person. If unconscious, place inrecovery position and get medical attention immediately. Maintain an open airway.

    Loosen tight clothing such as a collar, tie, belt or waistband.

    Get medical attention immediately. Call a poison center or physician. Wash with plentyof soap and water. Remove contaminated clothing and shoes. Wash contaminatedclothing thoroughly with water before removing it, or wear gloves. Continue to rinse forat least 10 minutes. Chemical burns must be treated promptly by a physician. In theevent of any complaints or symptoms, avoid further exposure. Wash clothing beforereuse. Clean shoes thoroughly before reuse.

    an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case ofinhalation of decomposition products in a fire, symptoms may be delayed. The exposedperson may need to be kept under medical surveillance for 48 hours.

    Skin contact

    Ingestion :

    :

    Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it issuspected that fumes are still present, the rescuer should wear an appropriate mask orself-contained breathing apparatus. It may be dangerous to the person providing aid togive mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with waterbefore removing it, or wear gloves.

    Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.The exposed person may need to be kept under medical surveillance for 48 hours.

    Specific treatments : No specific treatment.

    Most important symptoms/effects, acute and delayed

    Inhalation : No known significant effects or critical hazards.

    No known significant effects or critical hazards.:Ingestion

    Skin contact : Causes skin irritation. May cause an allergic skin reaction.

    Causes serious eye damage.:Eye contact

    Over-exposure signs/symptoms

    Skin contact

    Ingestion

    Inhalation No specific data.

    Adverse symptoms may include the following:stomach pains

    Adverse symptoms may include the following:pain or irritationrednessblistering may occur

    :

    :

    :

    Eye contact : Adverse symptoms may include the following:painwateringredness

    Potential acute health effects

    See toxicological information (Section 11)

    Indication of immediate medical attention and special treatment needed, if necessary

    Date of issue : 22.10.2015. 3/14

  • 7/25/2019 comp a

    4/14

    Jotamastic 87 Comp A

    Section 5. Fire-fighting measures

    Promptly isolate the scene by removing all persons from the vicinity of the incident ifthere is a fire. No action shall be taken involving any personal risk or without suitabletraining. Move containers from fire area if this can be done without risk. Use waterspray to keep fire-exposed containers cool.

    Hazardous thermal

    decomposition products

    Specific hazards arising

    from the chemical

    Decomposition products may include the following materials:carbon dioxidecarbon monoxidenitrogen oxideshalogenated compoundsmetal oxide/oxides

    Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur andthe container may burst, with the risk of a subsequent explosion. Runoff to sewer maycreate fire or explosion hazard. This material is harmful to aquatic life with long lastingeffects. Fire water contaminated with this material must be contained and preventedfrom being discharged to any waterway, sewer or drain.

    Fire-fighters should wear appropriate protective equipment and self-contained breathingapparatus (SCBA) with a full face-piece operated in positive pressure mode.

    Special protective

    equipment for fire-fighters

    Use dry chemical, CO,water spray (fog) or foam.

    Extinguishing media

    :

    :

    :

    Do not use water jet.

    Suitable extinguishing

    media

    :

    Unsuitable extinguishing

    media

    :

    Special protective actions

    for fire-fighters

    :

    Section 6. Accidental release measures

    Environmental precautions

    Personal precautions, protective equipment and emergency procedures

    Stop leak if without risk. Move containers from spill area. Use spark-proof tools andexplosion-proof equipment. Approach release from upwind. Prevent entry into sewers,water courses, basements or confined areas. Wash spillages into an effluent treatmentplant or proceed as follows. Contain and collect spillage with non-combustible,absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in

    container for disposal according to local regulations (see Section 13). Dispose of via alicensed waste disposal contractor. Contaminated absorbent material may pose thesame hazard as the spilled product. Note: see Section 1 for emergency contactinformation and Section 13 for waste disposal.

    :

    : No action shall be taken involving any personal risk or without suitable training.

    Evacuate surrounding areas. Keep unnecessary and unprotected personnel fromentering. Do not touch or walk through spilled material. Shut off all ignition sources.No flares, smoking or flames in hazard area. Do not breathe vapor or mist. Provideadequate ventilation. Wear appropriate respirator when ventilation is inadequate. Puton appropriate personal protective equipment.

    Avoid dispersal of spilled material and runoff and contact with soil, waterways, drainsand sewers. Inform the relevant authorities if the product has caused environmentalpollution (sewers, waterways, soil or air). Water polluting material. May be harmful to

    the environment if released in large quantities.

    Large spill :

    Stop leak if without risk. Move containers from spill area. Use spark-proof tools andexplosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,or if water-insoluble, absorb with an inert dry material and place in an appropriate wastedisposal container. Dispose of via a licensed waste disposal contractor.

    Small spill :

    Methods and materials for containment and cleaning up

    For non-emergency

    personnel

    For emergency responders : If specialised clothing is required to deal with the spillage, take note of any informationin Section 8 on suitable and unsuitable materials. See also the information in "For non-emergency personnel".

    Date of issue : 22.10.2015. 4/14

  • 7/25/2019 comp a

    5/14

    Jotamastic 87 Comp A

    Section 7. Handling and storage

    Advice on general

    occupational hygiene

    Conditions for safe storage,

    including any

    incompatibilities

    Eating, drinking and smoking should be prohibited in areas where this material ishandled, stored and processed. Workers should wash hands and face before eating,drinking and smoking. Remove contaminated clothing and protective equipment beforeentering eating areas. See also Section 8 for additional information on hygienemeasures.

    Store in accordance with local regulations. Store in a segregated and approved area.Store in original container protected from direct sunlight in a dry, cool and well-ventilatedarea, away from incompatible materials (see Section 10) and food and drink. Storelocked up. Eliminate all ignition sources. Separate from oxidizing materials. Keepcontainer tightly closed and sealed until ready for use. Containers that have beenopened must be carefully resealed and kept upright to prevent leakage. Do not store inunlabeled containers. Use appropriate containment to avoid environmentalcontamination.

    :

    :

    Protective measures Put on appropriate personal protective equipment (see Section 8). Persons with ahistory of skin sensitization problems should not be employed in any process in whichthis product is used. Do not get in eyes or on skin or clothing. Do not breathe vapor ormist. Do not ingest. Avoid release to the environment. Use only with adequate

    ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enterstorage areas and confined spaces unless adequately ventilated. Keep in the originalcontainer or an approved alternative made from a compatible material, kept tightlyclosed when not in use. Store and use away from heat, sparks, open flame or any otherignition source. Use explosion-proof electrical (ventilating, lighting and materialhandling) equipment. Use only non-sparking tools. Take precautionary measuresagainst electrostatic discharges. Empty containers retain product residue and can behazardous. Do not reuse container.

    :

    Precautions for safe handling

    xylene ACGIH TLV (United States, 4/2014).

    STEL: 651 mg/m 15 minutes. STEL: 150 ppm 15 minutes. TWA: 434 mg/m 8 hours.

    TWA: 100 ppm 8 hours.OSHA PEL (United States, 2/2013).

    TWA: 435 mg/m 8 hours. TWA: 100 ppm 8 hours.

    OSHA PEL 1989 (United States, 3/1989).

    STEL: 655 mg/m 15 minutes. STEL: 150 ppm 15 minutes. TWA: 435 mg/m 8 hours.

    TWA: 100 ppm 8 hours.benzyl alcohol AIHA WEEL (United States, 10/2011).

    TWA: 10 ppm 8 hours.2-methylpropan-1-ol ACGIH TLV (United States, 4/2014).

    TWA: 152 mg/m 8 hours.

    TWA: 50 ppm 8 hours.NIOSH REL (United States, 10/2013).

    TWA: 150 mg/m 10 hours. TWA: 50 ppm 10 hours.OSHA PEL (United States, 2/2013).

    TWA: 300 mg/m 8 hours. TWA: 100 ppm 8 hours.OSHA PEL 1989 (United States, 3/1989).

    TWA: 150 mg/m 8 hours. TWA: 50 ppm 8 hours.

    Section 8. Exposure controls/personal protection

    Ingredient name Exposure limits

    Control parameters

    Occupational exposure limits

    Date of issue : 22.10.2015. 5/14

  • 7/25/2019 comp a

    6/14

    Jotamastic 87 Comp A

    Section 8. Exposure controls/personal protectionethylbenzene OSHA PEL 1989 (United States, 3/1989).

    TWA: 100 ppm 8 hours. TWA: 435 mg/m 8 hours. STEL: 125 ppm 15 minutes. STEL: 545 mg/m 15 minutes.NIOSH REL (United States, 10/2013).

    TWA: 100 ppm 10 hours. TWA: 435 mg/m 10 hours. STEL: 125 ppm 15 minutes. STEL: 545 mg/m 15 minutes.OSHA PEL (United States, 2/2013).

    TWA: 100 ppm 8 hours. TWA: 435 mg/m 8 hours.

    ACGIH TLV (United States, 4/2014). Notes:

    K TWA: 20 ppm 8 hours. Form:

    Hand protection

    Use a properly fitted, air-purifying or air-fed respirator complying with an approvedstandard (NIOSH-approved P95) if a risk assessment indicates this is necessary.Respirator selection must be based on known or anticipated exposure levels, thehazards of the product and the safe working limits of the selected respirator.

    Chemical-resistant, impervious gloves complying with an approved standard should beworn at all times when handling chemical products if a risk assessment indicates this is

    necessary. Considering the parameters specified by the glove manufacturer, checkduring use that the gloves are still retaining their protective properties. It should benoted that the time to breakthrough for any glove material may be different for differentglove manufacturers. In the case of mixtures, consisting of several substances, theprotection time of the gloves cannot be accurately estimated.

    Safety eyewear complying with an approved standard should be used when a riskassessment indicates this is necessary to avoid exposure to liquid splashes, mists,gases or dusts. If contact is possible, the following protection should be worn, unlessthe assessment indicates a higher degree of protection: chemical splash goggles and/or face shield. If inhalation hazards exist, a full-face respirator may be required instead.

    Eye/face protection

    Respiratory protection :

    :

    :

    Body protection Personal protective equipment for the body should be selected based on the task beingperformed and the risks involved and should be approved by a specialist beforehandling this product. When there is a risk of ignition from static electricity, wear anti-static protective clothing. For the greatest protection from static discharges, clothingshould include anti-static overalls, boots and gloves.

    :

    Environmental exposure

    controls

    : Emissions from ventilation or work process equipment should be checked to ensurethey comply with the requirements of environmental protection legislation. In somecases, fume scrubbers, filters or engineering modifications to the process equipmentwill be necessary to reduce emissions to acceptable levels.

    Appropriate engineering

    controls

    : Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or

    other engineering controls to keep worker exposure to airborne contaminants below anyrecommended or statutory limits. The engineering controls also need to keep gas,vapor or dust concentrations below any lower explosive limits. Use explosion-proofventilation equipment.

    Wash hands, forearms and face thoroughly after handling chemical products, beforeeating, smoking and using the lavatory and at the end of the working period.

    Appropriate techniques should be used to remove potentially contaminated clothing.Contaminated work clothing should not be allowed out of the workplace. Washcontaminated clothing before reusing. Ensure that eyewash stations and safetyshowers are close to the workstation location.

    Hygiene measures :

    Individual protection measures

    Skin protection

    Other skin protection : Appropriate footwear and any additional skin protection measures should be selectedbased on the task being performed and the risks involved and should be approved by a

    specialist before handling this product.

    Date of issue : 22.10.2015. 6/14

  • 7/25/2019 comp a

    7/14

    Jotamastic 87 Comp A

    Section 9. Physical and chemical properties

    Physical state

    Melting point

    Vapor pressure

    Relative densityVapor density

    Solubility

    Liquid.

    Not available.

    1.44 to 1.555 g/cmNot available.

    Not available.

    Insoluble in the following materials: cold water and hot water.

    Characteristic.Odor

    pH

    Various colors.Color

    Evaporation rate Not available.

    Auto-ignition temperature

    Flash point

    Not available.

    Closed cup: 35C (95F)

    Not available.

    Not available.

    Viscosity Not available.

    Not available.Odor threshold

    Partition coefficient: n-

    octanol/water

    :

    :

    :

    :

    :

    :

    :

    :

    :

    :

    :

    :

    :

    :

    :

    Appearance

    Boiling point : Not available.

    Flammability (solid, gas) : Not available.

    Lower and upper explosive

    (flammable) limits

    : Not available.

    Decomposition temperature : Not available.

    12.02 to 12.98 pounds/gallon

    Section 10. Stability and reactivity

    Hazardous decomposition

    products

    Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,braze, solder, drill, grind or expose containers to heat or sources of ignition.

    Under normal conditions of storage and use, hazardous decomposition products shouldnot be produced.

    The product is stable.Chemical stability

    Reactive or incompatible with the following materials:

    oxidizing materials

    :

    :

    :

    Incompatible materials :

    Possibility of hazardous

    reactions

    : Under normal conditions of storage and use, hazardous reactions will not occur.

    Reactivity : No specific test data related to reactivity available for this product or its ingredients.

    Section 11. Toxicological information

    Acute toxicity

    Information on toxicological effects

    Date of issue : 22.10.2015. 7/14

  • 7/25/2019 comp a

    8/14

    Jotamastic 87 Comp A

    Section 11. Toxicological information

    xylene LC50 Inhalation Gas. Rat 6700 ppm 4 hoursLD50 Oral Rat 4300 mg/kg -

    2-methylpropan-1-ol LC50 Inhalation Vapor Rat 19200 mg/m 4 hoursLD50 Dermal Rabbit 3400 mg/kg -

    LD50 Oral Rat 2460 mg/kg -ethylbenzene LC50 Inhalation Gas. Rabbit 4000 ppm 4 hours

    LD50 Dermal Rabbit >5000 mg/kg -LD50 Oral Rat 3500 mg/kg -

    Product/ingredient name Result Species Dose Exposure

    Carcinogenicity

    Not available.

    Mutagenicity

    Not available.

    Teratogenicity

    Not available.

    Reproductive toxicity

    Not available.

    Irritation/Corrosion

    Not available.

    Sensitization

    Not available.

    Information on the likely

    routes of exposure

    Inhalation : No known significant effects or critical hazards.

    No known significant effects or critical hazards.:Ingestion

    Skin contact : Causes skin irritation. May cause an allergic skin reaction.

    Causes serious eye damage.:Eye contact

    Symptoms related to the physical, chemical and toxicological characteristics

    Specific target organ toxicity (single exposure)

    Specific target organ toxicity (repeated exposure)

    2-methylpropan-1-ol Category 3 Not applicable. Respiratory tractirritation andNarcotic effects

    Name Category

    Name Category

    ethylbenzene Category 2 Not determined ears

    Aspiration hazard

    Name Result

    ethylbenzene ASPIRATION HAZARD - Category 1

    Route of

    exposure

    Target organs

    Route of

    exposure

    Target organs

    : Not available.

    Potential acute health effects

    Classification

    xylene - 3 -

    Product/ingredient name NTPIARCOSHA

    Date of issue : 22.10.2015. 8/14

  • 7/25/2019 comp a

    9/14

    Jotamastic 87 Comp A

    Section 11. Toxicological information

    Not available.

    May cause damage to organs through prolonged or repeated exposure. Oncesensitized, a severe allergic reaction may occur when subsequently exposed to very lowlevels.

    General :

    No known significant effects or critical hazards.Carcinogenicity :

    No known significant effects or critical hazards.Mutagenicity :No known significant effects or critical hazards.Teratogenicity :

    Developmental effects : No known significant effects or critical hazards.

    Fertility effects : No known significant effects or critical hazards.

    Skin contact

    Ingestion

    Inhalation No specific data.

    Adverse symptoms may include the following:stomach pains

    Adverse symptoms may include the following:pain or irritationrednessblistering may occur

    :

    :

    :

    Eye contact : Adverse symptoms may include the following:painwateringredness

    Potential chronic health effects

    Delayed and immediate effects and also chronic effects from short and long term exposure

    Numerical measures of toxicity

    Oral 6520,8 mg/kgDermal 10620,7 mg/kg

    Inhalation (vapors) 77,6 mg/l

    Route ATE value

    Acute toxicity estimates

    Potential immediate

    effects

    : Not available.

    Short term exposure

    Potential delayed effects : Not available.

    Potential immediate

    effects

    : Not available.

    Long term exposure

    Potential delayed effects : Not available.

    Section 12. Ecological information

    Toxicity

    epoxy resin (MW 700) Acute EC50 1,4 mg/l Daphnia 48 hoursAcute LC50 3,1 mg/l Fish - fathead minnow 96 hours

    2-methylpropan-1-ol Chronic NOEC 4000 g/l Fresh water Daphnia - Daphnia magna 21 days

    ethylbenzene Acute EC50 7,2 mg/l Algae 48 hours

    Acute EC50 2,93 mg/l Daphnia 48 hoursAcute LC50 4,2 mg/l Fish 96 hours

    3-aminomethyl-3,5,5-trimethylcyclohexylamine

    Acute EC50 17,4 to 21,5 mg/l Freshwater

    Daphnia - Daphnia magna 48 hours

    Acute IC50 37 mg/l Algae 72 hours

    Product/ingredient name SpeciesResult Exposure

    Date of issue : 22.10.2015. 9/14

  • 7/25/2019 comp a

    10/14

    Jotamastic 87 Comp A

    Section 12. Ecological information

    LogPow BCF Potential

    Bioaccumulative potential

    Other adverse effects : No known significant effects or critical hazards.

    Product/ingredient name

    epoxy resin (MW 700) 2.64 to 3.78 31 lowxylene 3,12 8.1 to 25.9 lowhydrocarbons, c9-unsatd.,polymd.

    3,627 - low

    benzyl alcohol 0,87

  • 7/25/2019 comp a

    11/14

    Jotamastic 87 Comp A

    Section 14. Transport information

    Paint.

    3

    III

    Paint.

    3

    III

    Paint.

    1263

    3

    III

    1263 1263

    DOT

    Classification

    IMDG IATA

    UN number

    UN propershipping name

    Transport

    hazard class(es)

    Packing group

    Environmental

    hazards

    Special precautions for user

    Transport in bulk accordingto Annex II of MARPOL

    73/78 and the IBC Code

    No. No. No.

    Transport within users premises:always transport in closed containers that are

    upright and secure. Ensure that persons transporting the product know what to do in theevent of an accident or spillage.

    : Not available.

    :

    TDG

    Classification

    1263

    Paint.

    3

    III

    No.

    ADR/RID

    1263

    Paint.

    3

    III

    No.

    Mexico

    Classification

    1263

    Paint.

    3

    III

    No.

    Additional information

    Reportable quantity

    1245 lbs / 565,22 kg [99,71 gal / 377,44 L]Package sizes shipped in quantities less than the product reportable quantity are notsubject to the RQ (reportable quantity) transportation requirements.

    Emergency schedules (EmS): F-E, S-EMarine pollutant: No.

    -

    -

    Tunnel restriction code: (D/E)Hazard identification number: 30Special provisions: 640E

    -

    DOT Classification

    TDG Classification

    Mexico Classification

    ADR/RID

    IMDG

    IATA

    :

    :

    :

    :

    :

    :

    IMDG: Viscous substance. Transport in accordance with paragraph 2.3.2.5(applicable to receptacles < 30 litre capacity).

    ADR/RID: Viscous substance. Not restricted, ref. chapter 2.2.3.1.5 (applicable to

    receptacles < 450 litre capacity).

    Section 15. Regulatory information

    U.S. Federal regulations

    Clean Water Act (CWA) 307: ethylbenzene

    Clean Water Act (CWA) 311: xylene; ethylbenzene

    :

    Clean Air Act Section 112

    (b) Hazardous AirPollutants (HAPs)

    : Listed

    Clean Air Act Section 602

    Class I Substances

    : Not listed

    TSCA 8(a) CDR Exempt/Partial exemption: Not determined

    Not determined.

    Date of issue : 22.10.2015. 11/14

  • 7/25/2019 comp a

    12/14

    Jotamastic 87 Comp A

    Section 15. Regulatory information

    The following components are listed: BENZYL ALCOHOL; ISOBUTYL ALCOHOL;IRON OXIDE DUST; XYLENE

    WARNING:This product contains a chemical known to the State of California to cause cancer.

    Massachusetts :

    SARA 313

    Product name CAS number %

    SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include

    copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.

    xylene 1330-20-7 5 -

  • 7/25/2019 comp a

    13/14

    Jotamastic 87 Comp A

    Section 15. Regulatory information

    ethylbenzene Yes. No. 41 g/day (ingestion) No.54 g/day

    (inhalation)

    Ingredient name Cancer Reproductive No significant risk

    level

    Maximum

    acceptable dosage

    level

    International regulations

    Chemical Weapon Convention List Schedules I, II & III Chemicals

    Montreal Protocol (Annexes A, B, C, E)

    Not listed.

    Stockholm Convention on Persistent Organic Pollutants

    Not listed.

    Rotterdam Convention on Prior Inform Consent (PIC)

    Not listed.

    Not listed.

    UNECE Aarhus Protocol on POPs and Heavy Metals

    Not listed.

    International lists

    National inventory

    Australia : Not determined.

    Canada : Not determined.

    China : Not determined.

    Europe : Not determined.

    Japan : Not determined.

    Republic of Korea : Not determined.

    Malaysia : Not determined.

    New Zealand : Not determined.

    Philippines : Not determined.

    Taiwan : Not determined.

    Section 16. Other information

    22.10.2015.

    History

    Date of printing

    Date of issue/Date of

    revision

    Version

    Date of previous issue

    :

    :

    :

    :

    22.10.2015.

    27.05.2015.

    2

    Procedure used to derive the classification

    Classification Justification

    Flam. Liq. 3, H226 On basis of test dataSkin Irrit. 2, H315 Calculation methodEye Dam. 1, H318 Calculation methodSkin Sens. 1, H317 Calculation methodSTOT RE 2, H373 Calculation method

    Aquatic Chronic 3, H412 Calculation method

    Date of issue : 22.10.2015. 13/14

  • 7/25/2019 comp a

    14/14

    Jotamastic 87 Comp A

    Section 16. Other information

    To the best of our knowledge, the information contained herein is accurate. However, neither the above-named

    supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the

    information contained herein.

    Final determination of suitability of any material is the sole responsibility of the user. All materials may present

    unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot

    guarantee that these are the only hazards that exist.

    Notice to reader

    Indicates information that has changed from previously issued version.

    References : Not available.

    Key to abbreviations : ATE = Acute Toxicity EstimateBCF = Bioconcentration FactorGHS = Globally Harmonized System of Classification and Labelling of ChemicalsIATA = International Air Transport AssociationIBC = Intermediate Bulk ContainerIMDG = International Maritime Dangerous Goods

    LogPow = logarithm of the octanol/water partition coefficientMARPOL 73/78 = International Convention for the Prevention of Pollution From Ships,1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)UN = United Nations