Comp 361, Spring 20054: Network Layer1 Chapter 4: Network Layer Part I (last revised 22/03/05) r 4....
-
date post
21-Dec-2015 -
Category
Documents
-
view
221 -
download
0
Transcript of Comp 361, Spring 20054: Network Layer1 Chapter 4: Network Layer Part I (last revised 22/03/05) r 4....
4: Network Layer 1 Comp 361, Spring 2005
Chapter 4: Network Layer Part I (last revised 22/03/05)
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing (maybe)
4: Network Layer 2 Comp 361, Spring 2005
Network layer transport segment from sending to receiving
host on sending side encapsulates segments into
datagrams on rcving side, delivers segments to transport
layer network layer protocols in every host, router Router examines header fields in all IP
datagrams passing through it
networkdata linkphysical
networkdata linkphysical
networkdata linkphysical
networkdata linkphysical
networkdata linkphysical
networkdata linkphysical
networkdata linkphysical
networkdata linkphysical
application
transportnetworkdata linkphysical
application
transportnetworkdata linkphysical
4: Network Layer 3 Comp 361, Spring 2005
Key Network-Layer Functions
forwarding: move packets from router’s input to appropriate router output
routing: determine route taken by packets from source to dest.
Routing algorithms
analogy:
routing: process of planning trip from source to dest
forwarding: process of getting through single interchange
4: Network Layer 4 Comp 361, Spring 2005
1
23
0111
value in arrivingpacket’s header
routing algorithm
local forwarding tableheader value output link
0100010101111001
3221
Interplay between routing and forwarding
4: Network Layer 5 Comp 361, Spring 2005
3rd important function in some network architectures: ATM, frame relay, X.25 Before datagrams flow, two hosts and
intervening routers establish virtual connection Routers get involved
Network vs. transport layer cnctn service: Network: between two hosts Transport: between two processes
4: Network Layer 6 Comp 361, Spring 2005
Network service model
Q: What service model for “channel” transporting packets from sender to receiver?
guaranteed bandwidth? preservation of inter-
packet timing (no jitter)? loss-free delivery? in-order delivery? congestion feedback to
sender?
? ??virtual circuit
or datagram?
The most important abstraction provided
by network layer:
serv
ice a
bst
ract
ion
4: Network Layer 7 Comp 361, Spring 2005
Network layer service models:
NetworkArchitecture
Internet
ATM
ATM
ATM
ATM
ServiceModel
best effort
CBR
VBR
ABR
UBR
Bandwidth
none
constantrateguaranteedrateguaranteed minimumnone
Loss
no
yes
yes
no
no
Order
no
yes
yes
yes
yes
Timing
no
yes
yes
no
no
Congestionfeedback
no (inferredvia loss)nocongestionnocongestionyes
no
Guarantees ?
4: Network Layer 8 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 9 Comp 361, Spring 2005
Network layer connection and connection-less service
Datagram network provides network-layer connectionless service
VC network provides network-layer connection service
Analogous to the transport-layer services, but: Service: host-to-host No choice: network provides one or the
other Implementation: in the core
4: Network Layer 10 Comp 361, Spring 2005
Virtual circuits
call setup, teardown for each call before data can flow each packet carries VC identifier (not destination host OD) every router on source-dest paths maintain the “state” for
each passing connection transport-layer connection only involved two end systems
link, router resources (bandwidth, buffers) may be allocated to VC to get circuit-like performance
“source-to-dest path behaves much like telephone circuit” performance-wise network actions along source-to-dest path
4: Network Layer 11 Comp 361, Spring 2005
VC implementation
A VC consists of:1. Path from source to destination2. VC numbers, one number for each link along
path3. Entries in forwarding tables in routers along
path Packet belonging to VC carries a VC
number. VC number must be changed on each
link. New VC number comes from forwarding table
4: Network Layer 12 Comp 361, Spring 2005
Forwarding table
12 22 32
1 23
VC number
interfacenumber
Incoming interface Incoming VC # Outgoing interface Outgoing VC #
1 12 2 222 63 1 18 3 7 2 171 97 3 87… … … …
Forwarding table inupper-left router:
Routers maintain connection state information!
4: Network Layer 13 Comp 361, Spring 2005
Virtual circuits: signaling protocols used to setup, maintain teardown VC connection setup process still needs routing
much as in the Internet used in ATM, frame-relay, X.25 not used in today’s Internet
application
transportnetworkdata linkphysical
application
transportnetworkdata linkphysical
1. Initiate call 2. incoming call
3. Accept call4. Call connected5. Data flow begins 6. Receive data
4: Network Layer 14 Comp 361, Spring 2005
Datagram networks no call setup at network layer routers: no state info about end-to-end connections
no network-level concept of “connection”
packets forwarded using destination host address packets between same source-dest pair may take different
paths
application
transportnetworkdata linkphysical
application
transportnetworkdata linkphysical
1. Send data 2. Receive data
4: Network Layer 15 Comp 361, Spring 2005
Forwarding table
Destination Address Range Link Interface
11001000 00010111 00010000 00000000 through 0 11001000 00010111 00010111 11111111
11001000 00010111 00011000 00000000 through 1 11001000 00010111 00011000 11111111
11001000 00010111 00011001 00000000 through 2 11001000 00010111 00011111 11111111
otherwise 3
4 billion possible entries
4: Network Layer 16 Comp 361, Spring 2005
Longest prefix matching
Prefix Match Link Interface 11001000 00010111 00010 0 11001000 00010111 00011000 1 11001000 00010111 00011 2 otherwise 3
DA: 11001000 00010111 00011000 10101010
Examples
DA: 11001000 00010111 00010110 10100001 Which interface?
Which interface?
4: Network Layer 17 Comp 361, Spring 2005
Datagram or VC network: why?
Internet data exchange among
computers “elastic” service, no
strict timing req. “smart” end systems
(computers) can adapt, perform
control, error recovery simple inside network,
complexity at “edge” many link types
different characteristics uniform service difficult
ATM evolved from telephony human conversation:
strict timing, reliability requirements
need for guaranteed service
“dumb” end systems telephones complexity inside
network
4: Network Layer 18 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 19 Comp 361, Spring 2005
Router Architecture Overview
Two key router functions: run routing algorithms/protocol (RIP, OSPF, BGP) forwarding datagrams from incoming to outgoing link
4: Network Layer 20 Comp 361, Spring 2005
Input Port Functions
Decentralized switching: given datagram dest., lookup output
port using forwarding table in input port memory
goal: complete input port processing at ‘line speed’
queuing: if datagrams arrive faster than forwarding rate into switch fabric
Physical layer:bit-level reception
Data link layer:e.g., Ethernetsee chapter 5
4: Network Layer 21 Comp 361, Spring 2005
Three types of switching fabrics
4: Network Layer 22 Comp 361, Spring 2005
Switching Via MemoryFirst generation routers: packet copied by system’s (single) CPU speed limited by memory bandwidth (2 bus crossings per datagram)
InputPort
OutputPort
Memory
System Bus
Modern routers: input port processor performs lookup, copy into memory Cisco Catalyst 8500
4: Network Layer 23 Comp 361, Spring 2005
Switching Via a Bus
datagram from input port memory
to output port memory via a shared bus
bus contention: switching speed limited by bus bandwidth
1 Gbps bus, Cisco 1900: sufficient speed for access and enterprise routers (not regional or backbone)
4: Network Layer 24 Comp 361, Spring 2005
Switching Via An Interconnection Network
overcome bus bandwidth limitations Banyan networks, other interconnection nets
initially developed to connect processors in multiprocessor
Advanced design: fragmenting datagram into fixed length cells, switch cells through the fabric.
Cisco 12000: switches Gbps through the interconnection network
4: Network Layer 25 Comp 361, Spring 2005
Output Ports
Buffering required when datagrams arrive from fabric faster than the transmission rate
Scheduling discipline chooses among queued datagrams for transmission
4: Network Layer 26 Comp 361, Spring 2005
Output port queueing
buffering when arrival rate via switch exceeds output line speed
queueing (delay) and loss due to output port buffer overflow!
4: Network Layer 27 Comp 361, Spring 2005
Input Port Queuing
Fabric slower than input ports combined -> queueing may occur at input queues
Head-of-the-Line (HOL) blocking: queued datagram at front of queue prevents others in queue from moving forward
queueing delay and loss due to input buffer overflow!
4: Network Layer 28 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 29 Comp 361, Spring 2005
The Internet Network layer
forwardingtable
Host, router network layer functions:
Routing protocols•path selection•RIP, OSPF, BGP
IP protocol•addressing conventions•datagram format•packet handling conventions
ICMP protocol•error reporting•router “signaling”
Transport layer: TCP, UDP
Link layer
physical layer
Networklayer
4: Network Layer 30 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 31 Comp 361, Spring 2005
IP datagram format
ver length
32 bits
data (variable length,typically a TCP
or UDP segment)
16-bit identifier
Internet checksum
time tolive
32 bit source IP address
IP protocol versionnumber
header length (bytes)
max numberremaining hops
(decremented at each router)
forfragmentation/reassembly
total datagramlength (bytes)
upper layer protocolto deliver payload to
head.len
type ofservice
“type” of data flgsfragment
offsetupper layer
32 bit destination IP address
Options (if any) E.g. timestamp,record routetaken, specifylist of routers to visit.
how much overhead with TCP?
20 bytes of TCP 20 bytes of IP = 40 bytes + app
layer overhead
4: Network Layer 32 Comp 361, Spring 2005
IP Fragmentation & Reassembly network links have MTU
(max.transfer size) - largest possible link-level frame. different link types,
different MTUs large IP datagram divided
(“fragmented”) within net one datagram becomes
several datagrams “reassembled” only at
final destination IP header bits used to
identify, order related fragments
fragmentation: in: one large datagramout: 3 smaller datagrams
reassembly
4: Network Layer 33 Comp 361, Spring 2005
IP Fragmentation and Reassembly
ID=x
offset=0
fragflag=0
length=4000
ID=x
offset=0
fragflag=1
length=1500
ID=x
offset=185
fragflag=1
length=1500
ID=x
offset=370
fragflag=0
length=1040
One large datagram becomesseveral smaller datagrams
Example 4000 byte
datagram MTU = 1500 bytes
1480 bytes in data field
offset =1480/8
4: Network Layer 34 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 35 Comp 361, Spring 2005
IP Addressing: introduction IP address: 32-bit
identifier for host, router interface
interface: connection between host/router and physical link router’s typically
have multiple interfaces
host may have multiple interfaces
IP addresses associated with each interface, not with host or router
223.1.1.1
223.1.1.2
223.1.1.3
223.1.1.4 223.1.2.9
223.1.2.2
223.1.2.1
223.1.3.2223.1.3.1
223.1.3.27
223.1.1.1 = 11011111 00000001 00000001 00000001
223 1 11
4: Network Layer 36 Comp 361, Spring 2005
Subnets IP address:
subnet part (high order bits)
host part (low order bits)
What’s a subnet ? device interfaces
with same subnet part of IP address
can physically reach each other without intervening router
223.1.1.1
223.1.1.2
223.1.1.3
223.1.1.4 223.1.2.9
223.1.2.2
223.1.2.1
223.1.3.2223.1.3.1
223.1.3.27
network consisting of 3 subnets (for IP addresses starting with 223, first 24 bits are network address)
LAN
4: Network Layer 37 Comp 361, Spring 2005
Subnets 223.1.1.0/24223.1.2.0/24
223.1.3.0/24
Recipe To determine the
subnets, detach each interface from its host or router, creating islands of isolated networks. Each isolated network is called a subnet. Subnet mask: /24
4: Network Layer 38 Comp 361, Spring 2005
SubnetsHow many? 223.1.1.1
223.1.1.3
223.1.1.4
223.1.2.2223.1.2.1
223.1.2.6
223.1.3.2223.1.3.1
223.1.3.27
223.1.1.2
223.1.7.0
223.1.7.1223.1.8.0223.1.8.1
223.1.9.1
223.1.9.2
4: Network Layer 39 Comp 361, Spring 2005
IP Addresses
0network host
10 network host
110 network host
1110 multicast address
A
B
C
D
class1.0.0.0 to127.255.255.255
128.0.0.0 to191.255.255.255
192.0.0.0 to223.255.255.255
224.0.0.0 to239.255.255.255
32 bits
given notion of “network”, let’s re-examine IP addresses:
“class-full” addressing:
4: Network Layer 40 Comp 361, Spring 2005
IP addressing: CIDR classful addressing:
inefficient use of address space, address space exhaustion
e.g., class B net allocated enough addresses for 65K hosts, even if only 2K hosts in that network
CIDR: Classless InterDomain Routing network portion of address of arbitrary length address format: a.b.c.d/x, where x is # bits in network
portion of address
11001000 00010111 00010000 00000000
networkpart
hostpart
200.23.16.0/23
4: Network Layer 41 Comp 361, Spring 2005
IP addresses: how to get one?
Q: How does host get IP address?
hard-coded by system admin in a file Wintel: control-panel->network->configuration->tcp/ip-
>properties UNIX: /etc/rc.config
DHCP: Dynamic Host Configuration Protocol: dynamically get address from server “plug-and-play”
(more later)
4: Network Layer 42 Comp 361, Spring 2005
IP addresses: how to get one?
Q: How does network get subnet part of IP addr?
A: gets allocated portion of its provider ISP’s address space
ISP's block 11001000 00010111 00010000 00000000 200.23.16.0/20
Organization 0 11001000 00010111 00010000 00000000 200.23.16.0/23 Organization 1 11001000 00010111 00010010 00000000 200.23.18.0/23 Organization 2 11001000 00010111 00010100 00000000 200.23.20.0/23 ... ….. …. ….
Organization 7 11001000 00010111 00011110 00000000 200.23.30.0/23
4: Network Layer 43 Comp 361, Spring 2005
Hierarchical addressing: route aggregation
“Send me anythingwith addresses beginning 200.23.16.0/20”
200.23.16.0/23
200.23.18.0/23
200.23.30.0/23
Fly-By-Night-ISP
Organization 0
Organization 7Internet
Organization 1
ISPs-R-Us“Send me anythingwith addresses beginning 199.31.0.0/16”
200.23.20.0/23Organization 2
...
...
Hierarchical addressing allows efficient advertisement of routing information:
4: Network Layer 44 Comp 361, Spring 2005
Hierarchical addressing: more specific routes
ISPs-R-Us has a more specific route to Organization 1
“Send me anythingwith addresses beginning 200.23.16.0/20”
200.23.16.0/23
200.23.18.0/23
200.23.30.0/23
Fly-By-Night-ISP
Organization 0
Organization 7Internet
Organization 1
ISPs-R-Us“Send me anythingwith addresses beginning 199.31.0.0/16or 200.23.18.0/23”
200.23.20.0/23Organization 2
...
...
4: Network Layer 45 Comp 361, Spring 2005
IP addressing: the last word...
Q: How does an ISP get block of addresses?
A: ICANN: Internet Corporation for Assigned
Names and Numbers allocates addresses manages DNS assigns domain names, resolves disputes
4: Network Layer 46 Comp 361, Spring 2005
NAT: Network Address Translation
10.0.0.1
10.0.0.2
10.0.0.3
10.0.0.4
138.76.29.7
local network(e.g., home network)
10.0.0/24
rest ofInternet
Datagrams with source or destination in this networkhave 10.0.0/24 address for
source, destination (as usual)
All datagrams leaving localnetwork have same single source
NAT IP address: 138.76.29.7,different source port numbers
4: Network Layer 47 Comp 361, Spring 2005
NAT: Network Address Translation
Motivation: local network uses just one IP address as far as outside word is concerned: no need to be allocated range of addresses from
ISP: - just one IP address is used for all devices can change addresses of devices in local network
without notifying outside world can change ISP without changing addresses of
devices in local network devices inside local net not explicitly
addressable, visible by outside world (a security plus).
4: Network Layer 48 Comp 361, Spring 2005
NAT: Network Address Translation
Implementation: NAT router must:
in outgoing datagrams: replace (source IP address, port #) of every outgoing datagram to (NAT IP address, new port #). . . remote clients/servers will respond using (NAT IP
address, new port #) as destination addr.
remember (in NAT translation table) every (source IP address, port #) to (NAT IP address, new port #) translation pair
in incoming datagrams: replace (NAT IP address, new port #) in dest fields of every incoming datagram with corresponding (source IP address, port #) stored in NAT table
4: Network Layer 49 Comp 361, Spring 2005
NAT: Network Address Translation
10.0.0.1
10.0.0.2
10.0.0.3
S: 10.0.0.1, 3345D: 128.119.40.186, 80
1
10.0.0.4
138.76.29.7
1: host 10.0.0.1 sends datagram to 128.119.40, 80
NAT translation tableWAN side addr LAN side addr
138.76.29.7, 5001 10.0.0.1, 3345…… ……
S: 128.119.40.186, 80 D: 10.0.0.1, 3345
4
S: 138.76.29.7, 5001D: 128.119.40.186, 80
2
2: NAT routerchanges datagramsource addr from10.0.0.1, 3345 to138.76.29.7, 5001,updates table
S: 128.119.40.186, 80 D: 138.76.29.7, 5001
3
3: Reply arrives dest. address: 138.76.29.7, 5001
4: NAT routerchanges datagramdest addr from138.76.29.7, 5001 to 10.0.0.1, 3345
4: Network Layer 50 Comp 361, Spring 2005
NAT: Network Address Translation
16-bit port-number field: 60,000 simultaneous connections with a
single LAN-side address! NAT is controversial:
routers should only process up to layer 3 violates end-to-end argument
• NAT possibility must be taken into account by app designers, eg, P2P applications
address shortage should instead be solved by IPv6
4: Network Layer 51 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 52 Comp 361, Spring 2005
ICMP: Internet Control Message Protocol
used by hosts & routers to communicate network-level information error reporting:
unreachable host, network, port, protocol
echo request/reply (used by ping)
network-layer “above” IP: ICMP msgs carried in IP
datagrams ICMP message: type, code
plus first 8 bytes of IP datagram causing error
Type Code description0 0 echo reply (ping)3 0 dest. network unreachable3 1 dest host unreachable3 2 dest protocol unreachable3 3 dest port unreachable3 6 dest network unknown3 7 dest host unknown4 0 source quench (congestion control - not used)8 0 echo request (ping)9 0 route advertisement10 0 router discovery11 0 TTL expired12 0 bad IP header
4: Network Layer 53 Comp 361, Spring 2005
Traceroute and ICMP
Source sends series of UDP segments to dest First has TTL =1 Second has TTL=2, etc. Unlikely port number
When nth datagram arrives to nth router: Router discards
datagram And sends to source an
ICMP message (type 11, code 0)
Message includes name of router& IP address
When ICMP message arrives, source calculates RTT
Traceroute does this 3 times
Stopping criterion UDP segment eventually
arrives at destination host
Destination returns ICMP “host unreachable” packet (type 3, code 3)
When source gets this ICMP, stops.
4: Network Layer 54 Comp 361, Spring 2005
Chapter 4: Network Layer
4. 1 Introduction 4.2 Virtual circuit
and datagram networks
4.3 What’s inside a router
4.4 IP: Internet Protocol Datagram format IPv4 addressing ICMP IPv6
4.5 Routing algorithms Link state Distance Vector Hierarchical routing
4.6 Routing in the Internet RIP OSPF BGP
4.7 Broadcast and multicast routing
4: Network Layer 55 Comp 361, Spring 2005
IPv6 Initial motivation: 32-bit address space
soon to be completely allocated. Additional motivation:
header format helps speed processing/forwarding
header changes to facilitate QoS IPv6 datagram format: fixed-length 40 byte header no fragmentation allowed
4: Network Layer 56 Comp 361, Spring 2005
IPv6 Header (Cont)Priority: identify priority among datagrams in flowFlow Label: identify datagrams in same “flow.” (concept of“flow” not well defined).Next header: identify upper layer protocol for data
4: Network Layer 57 Comp 361, Spring 2005
Other Changes from IPv4
Checksum: removed entirely to reduce processing time at each hop
Options: allowed, but outside of header, indicated by “Next Header” field
ICMPv6: new version of ICMP additional message types, e.g. “Packet Too
Big” multicast group management functions
4: Network Layer 58 Comp 361, Spring 2005
Transition From IPv4 To IPv6
Not all routers can be upgraded simultaneous no “flag days” How will the network operate with mixed IPv4
and IPv6 routers? Two proposed approaches:
Dual Stack: some routers with dual stack (v6, v4) can “translate” between formats
Tunneling: IPv6 carried as payload in IPv4 datagram among IPv4 routers
4: Network Layer 59 Comp 361, Spring 2005
TunnelingA B E F
IPv6 IPv6 IPv6 IPv6
tunnelLogical view:
Physical view:A B E F
IPv6 IPv6 IPv6 IPv6
C D
IPv4 IPv4
Flow: XSrc: ADest: F
data
Flow: XSrc: ADest: F
data
Flow: XSrc: ADest: F
data
Src:BDest: E
Flow: XSrc: ADest: F
data
Src:BDest: E
A-to-B:IPv6
E-to-F:IPv6
B-to-C:IPv6 inside
IPv4
B-to-C:IPv6 inside
IPv4