Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU)...

29
Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for machinery drafted in support of Directive 2006/42/EC of the European Parliament and of the Council COMMISSION IMPLEMENTING DECISION (EU) 2019/436 of 18 March 2019 on the harmonised standards for machinery drafted in support of Directive 2006/42/EC of the European Parliament and of the Council THE EUROPEAN COMMISSION, Having regard to the Treaty on the Functioning of the European Union, Having regard to Regulation (EU) No 1025/2012 of the European Parliament and of the Council of 25 October 2012 on European standardisation, amending Council Directives 89/686/EEC and 93/15/EEC and Directives 94/9/EC, 94/25/EC, 95/16/EC, 97/23/EC, 98/34/EC, 2004/22/ EC, 2007/23/EC, 2009/23/EC and 2009/105/EC of the European Parliament and of the Council and repealing Council Decision 87/95/EEC and Decision No 1673/2006/EC of the European Parliament and of the Council (1) , and in particular Article 10(6) thereof, Having regard to Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (2) , and in particular Article 7(3) and Article 10 thereof. Whereas: (1) In accordance with Article 7 of Directive 2006/42/EC machinery manufactured in conformity with a harmonised standard, the references to which have been published in the Official Journal of the European Union, is to be presumed to comply with the essential health and safety requirements covered by such a harmonised standard. (2) There are three types of harmonised standards conferring a presumption of conformity with Directive 2006/42/EC. (3) A-type standards specify basic concepts, terminology and design principles applicable to all categories of machinery. Application of such standards alone, although providing an essential framework for the correct application of the Directive 2006/42/EC, is not sufficient to ensure conformity with the relevant essential health and safety requirements of Directive 2006/42/EC and therefore does not give a full presumption of conformity. (4) B-type standards deal with specific aspects of machinery safety or specific types of safeguard that can be used across a wide range of categories of machinery. Application of the specifications of B-type standards confers a presumption of conformity with the essential health and safety requirements of Directive 2006/42/EC that they cover when a C-type standard or the manufacturer's risk assessment shows that a technical solution specified by the B-type standard is adequate for the particular category or model of

Transcript of Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU)...

Page 1: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Commission Implementing Decision (EU) 2019/436 of 18 March2019 on the harmonised standards for machinery drafted in support ofDirective 2006/42/EC of the European Parliament and of the Council

COMMISSION IMPLEMENTING DECISION (EU) 2019/436

of 18 March 2019

on the harmonised standards for machinery drafted in support ofDirective 2006/42/EC of the European Parliament and of the Council

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Regulation (EU) No 1025/2012 of the European Parliament and of the Councilof 25 October 2012 on European standardisation, amending Council Directives 89/686/EECand 93/15/EEC and Directives 94/9/EC, 94/25/EC, 95/16/EC, 97/23/EC, 98/34/EC, 2004/22/EC, 2007/23/EC, 2009/23/EC and 2009/105/EC of the European Parliament and of the Counciland repealing Council Decision 87/95/EEC and Decision No 1673/2006/EC of the EuropeanParliament and of the Council(1), and in particular Article 10(6) thereof,

Having regard to Directive 2006/42/EC of the European Parliament and of the Council of17 May 2006 on machinery, and amending Directive 95/16/EC(2), and in particular Article 7(3)and Article 10 thereof.

Whereas:

(1) In accordance with Article 7 of Directive 2006/42/EC machinery manufactured inconformity with a harmonised standard, the references to which have been publishedin the Official Journal of the European Union, is to be presumed to comply with theessential health and safety requirements covered by such a harmonised standard.

(2) There are three types of harmonised standards conferring a presumption of conformitywith Directive 2006/42/EC.

(3) A-type standards specify basic concepts, terminology and design principles applicableto all categories of machinery. Application of such standards alone, although providingan essential framework for the correct application of the Directive 2006/42/EC, isnot sufficient to ensure conformity with the relevant essential health and safetyrequirements of Directive 2006/42/EC and therefore does not give a full presumptionof conformity.

(4) B-type standards deal with specific aspects of machinery safety or specific types ofsafeguard that can be used across a wide range of categories of machinery. Applicationof the specifications of B-type standards confers a presumption of conformity with theessential health and safety requirements of Directive 2006/42/EC that they cover whena C-type standard or the manufacturer's risk assessment shows that a technical solutionspecified by the B-type standard is adequate for the particular category or model of

Page 2: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

2 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

machinery concerned. Application of B-type standards that give specifications forsafety components that are independently placed on the market confers a presumptionof conformity for the safety components concerned and for the essential health andsafety requirements covered by the standards.

(5) C-type standards provide specifications for a given category of machinery. The differenttypes of machinery belonging to the category covered by a C-type standard have asimilar intended use and present similar hazards. C-type standards may refer to A-type or B-type standards, indicating which of the specifications of the A-type or B-type standard are applicable to the category of machinery concerned. When, for a givenaspect of machinery safety, a C-type standard deviates from the specifications of anA or B-type standard, the specifications of the C-type standard take precedence overthe specifications of the A-type or B-type standard. Application of the specificationsof a C-type standard on the basis of the manufacturers' risk assessment confersa presumption of conformity with the essential health and safety requirements ofDirective 2006/42/EC covered by the standard. Certain C-type standards are organisedas a series of several parts, Part 1 of the standard giving general specifications applicableto a family of machinery and other parts of the standard giving specifications forspecific categories of machinery belonging to the family, supplementing or modifyingthe general specifications of Part 1. For C-type standards organised in this way,the presumption of conformity with the essential health and safety requirements ofDirective 2006/42/EC is conferred by application of the general Part 1 of the standardtogether with the relevant specific part of the standard.

(6) By letter M/396 of 19 December 2006, the Commission made a request to CEN andCenelec for the drafting, the revision and the completion of the work on harmonisedstandards in support of Directive 2006/42/EC to take account of changes introduced bythat Directive in comparison with Directive 98/37/EC of the European Parliament andof the Council(3).

(7) On the basis of the request M/396 of 19 December 2006 CEN and Cenelecdrafted new harmonised standards and revised and amended the existing harmonisedstandards. Harmonised standard EN 15895:2011+A1:2018 covers portable cartridge-operated fixing and other impact machinery introduced into the scope of Directive2006/42/EC. Standards EN 50569:2013/A1:2018; EN 50570:2013/A1:2018; EN50571:2013/A1:2018; EN 50636-2-107:2015/A1:2018; EN 60335-1:2012/A13:2017;EN 60335-2-58:2005; EN 60335-2-58:2005/A12:2016; EN 60335-2-58:2005/A2:2015and their amendments take account of the redefined borderline between Directive2006/42/EC and Directive 2014/35/EU of the European Parliament and of the Council(4)

and the fact that some household and similar electrical appliances subject to theDirective 2014/35/EU become subject to the Directive 2006/42/EC. Standard EN16719:2018 takes account of the fact that Directive 2006/42/EC amends Directive95/16/EC of the European Parliament and of the Council(5) with the effect that liftingappliances with a speed no greater than 0,15 m/s are subject to the Directive 2006/42/EC. Standards EN ISO 14118:2018; EN 474-1:2006+A5:2018; EN 1853:2017; EN1870-6:2017; EN ISO 4254-5:2018; EN ISO 4254-7:2017; EN ISO 4254-8:2018;EN ISO 5395-1:2013/A1:2018; EN ISO 5395-3:2013/A2:2018; EN 12013:2018;

Page 3: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

3

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

EN 12999:2011+A2:2018; EN 13001-3-1:2012+A2:2018; EN 13001-3-6:2018; EN13135:2013+A1:2018; EN 13684:2018; EN ISO 13766-2:2018; EN 15194:2017;EN 15895:2011+A1:2018 EN ISO 16092-1:2018; EN ISO 16092-3:2018; EN16952:2018; EN 16719:2018; EN 17059:2018; EN ISO 19085-4:2018; ENISO 19085-6:2017; EN ISO 19085-8:2018; EN ISO 19225:2017; EN ISO28927-2:2009/A1:2017; EN 50569:2013/A1:2018; EN 50570:2013/A1:2018; EN50571:2013/A1:2018; EN 50636-2-107:2015/A1:2018; EN 60335-1:2012/A13:2017;EN 62841-2-1:2018; EN 62841-2-17:2017; EN 62841-3-1:2014/A11:2017; EN60335-2-58:2005; EN 60335-2-58:2005/A2:2015; EN 60335-2-58:2005/A12:2016;EN 62841-2-1:2018; EN 62841-2-17:2017; EN 62841-3-1:2014/A11:2017; EN62841-3-4:2016; EN 62841-3-4:2016/A11:2017; EN 62841-3-6:2014/A11:2017; EN62841-3-9:2015/A11:2017; EN 62841-3-10:2015/A11:2017; EN 62841-3-14:2017 andtheir amendments ensure that the harmonised standards intended to support Directive2006/42/EC fully satisfy the relevant essential health and safety requirements of thatDirective.

(8) The Commission together with CEN and Cenelec has assessed whether the standardsdrafted, revised and amended by CEN and Cenelec comply with the request M/396 of19 December 2006.

(9) The standards drafted, revised and amended by CEN and Cenelec on the basis of requestM/396 of 19 December 2006 satisfy the requirements which they aim to cover andwhich are set out in Directive 2006/42/EC. It is therefore appropriate to publish thereferences of those standards in the Official Journal of the European Union.

(10) Under Article 10 of Directive 2006/42/EC the Commission sought opinion of thecommittee set up by Regulation (EU) No 1025/2012 on whether a harmonisedstandard EN 474-1:2006+A4:2013 satisfies the essential health and safety requirementswhich it covers and which are set out in Annex I to Directive 2006/42/EC. In thelight of the committee's opinion, the reference of standard EN 474-1:2006+A4:2013was published in the Official Journal of the European Union with a restriction byCommission Implementing Decision (EU) 2015/27(6). CEN improved the standardin the version EN 474-1:2006+A5:2018. However, the new version does notaddress one type of earthmoving machinery, i.e. hydraulic excavators. StandardEN 474-1:2006+A5:2018 therefore does not fully meet the essential health and safetyrequirements set out in points 1.2.2 and 3.2.1 of Annex I to Directive 2006/42/EC. Itshould therefore be published in the Official Journal of the European Union with arestriction.

(11) Under Article 10 of Directive 2006/42/EC the Commission sought opinion of thecommittee set up by Regulation (EU) No 1025/2012 on whether a harmonised standardEN 13241-1:2003+A1:2011 satisfies the essential health and safety requirements whichit covers and which are set out in Annex I to Directive 2006/42/EC. In the lightof the committee's opinion, the reference of standard EN 13241-1:2003+A1:2011was published in the Official Journal of the European Union with a restrictionby Commission Implementing Decision (EU) 2015/1301(7). CEN has improved thestandard in the version EN 13241:2003+A2:2016. However, the new version does not

Page 4: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

4 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

address the issues that led to a publication with a restriction of the previous version ofthe standard. The current version of that standard, EN 13241:2003+A2:2016, thereforedoes not fully meet the essential health and safety requirements set out in points 1.3.7and 1.4.3 of Annex I to Directive 2006/42/EC. It should therefore be published in theOfficial Journal of the European Union with a restriction.

(12) As the result of the work by CEN and Cenelec on the basis of request M/396 of19 December 2006 several harmonised standards published in the Official Journal ofthe European Union(8) have been replaced, revised or amended.

(13) It is therefore necessary to withdraw the references of those standards from the OfficialJournal of the European Union. In order to give manufacturers sufficient time to preparefor application of the new standards, revised standards and amendments to standards,it is necessary to defer the withdrawal of the references of harmonised standards.

(14) Harmonised standards EN 786:1996+A2:2009; EN 61496-1:2013; EN ISO 11200:2014and EN ISO 12100:2010 should be withdrawn as they no longer satisfy the requirementswhich they aim to cover and which are set out in Directive 2006/42/EC.

(15) Compliance with a harmonised standard confers a presumption of conformity with thecorresponding essential requirements set out in Union harmonisation legislation fromthe date of publication of the reference of such standard in the Official Journal ofthe European Union. This Decision should therefore enter into force on the day of itspublication,

HAS ADOPTED THIS DECISION:

Article 1

The references of harmonised standards for machinery drafted in support of Directive2006/42/EC listed in Annex I to this Decision are hereby published in the OfficialJournal of the European Union.

The references of harmonised standards drafted in support of Directive 2006/42/EClisted in Annex II to this Decision are hereby published in the Official Journal of theEuropean Union with a restriction.

Article 2

The references of harmonised standards for machinery drafted in support of Directive2006/42/EC listed in Annex III to this Decision are hereby withdrawn from the OfficialJournal of the European Union as from the dates set out in that Annex.

Article 3

This Decision shall enter into force on the day of its publication in the Official Journalof the European Union.

Page 5: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

5

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

ANNEX I

No Reference of the standard Type1. EN ISO 14118:2018

Safety of machinery —Prevention of unexpectedstart-up (ISO 14118:2017)

B

2. EN 1853:2017Agricultural machinery —Trailers – Safety

C

3. EN 1870-6:2017Safety of woodworkingmachines — Circular sawingmachines — Part 6: Circularsawing machines for firewood

C

4. EN ISO 4254-5:2018Agricultural machinery —Safety — Part 5: Power-driven soil-working machines(ISO 4254-5:2018)

C

5. EN ISO 4254-7:2017Agricultural machinery —Safety — Part 7: Combineharvesters, forage harvesters,cotton harvesters and sugarcane harversters (ISO4254-7:2017)

C

6. EN ISO 4254-8:2018Agricultural machinery —Safety — Part 8: Solidfertilizer distributors (ISO4254-8:2018)

C

7. EN ISO 5395-1:2013Garden equipment —Safety requirements forcombustion-engine-poweredlawnmowers — Part 1:Terminology and commontests (ISO 5395-1:2013)EN ISO 5395-1:2013/A1:2018

C

8. EN ISO 5395-3:2013Garden equipment —Safety requirements forcombustion-engine-poweredlawnmowers — Part 3: Ride-on lawnmowers with seatedoperator (ISO 5395-3:2013)

C

Page 6: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

6 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

EN ISO 5395-3:2013/A1:2017EN ISO 5395-3:2013/A2:2018

9. EN 12013:2018Plastics and rubbermachines — Internalmixers — Safetyrequirements

C

10. EN 12999:2011+A2:2018Cranes — Loader cranes

C

11. EN13001-3-1:2012+A2:2018Cranes — General Design —Part 3-1: Limit States andproof competence of steelstructure

C

12. EN 13001-3-6:2018Cranes — General design —Part 3-6: Limit states andproof of competence ofmachinery — Hydrauliccylinders

C

13. EN 13135:2013+A1:2018Cranes — Safety —Design — Requirements forequipment

C

14. EN 13684:2018Garden equipment —Pedestrian controlled lawnaerators and scarifiers –Safety

C

15. EN ISO 13766-2:2018Earth-moving and buildingconstruction machinery —Electromagneticcompatibility (EMC) ofmachines with internalelectrical power supply —Part 2: Additional EMCrequirements for functionalsafety (ISO 13766-2:2018)

C

16. EN 15194:2017Cycles — Electrically powerassisted cycles — EPACBicycles

C

17. EN 15895:2011+A1:2018 C

Page 7: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

7

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Cartridge operated hand-held tools — Safetyrequirements — Fixing andhard marking tools

18. EN ISO 16092-1:2018Machine tools safety —Presses — Part 1: Generalsafety requirements (ISO16092-1:2017)

C

19. EN ISO 16092-3:2018Machine tools safety —Presses — Part 3: Safetyrequirements for hydraulicpresses (ISO 16092-3:2017)

C

20. EN 16719:2018Transport platforms

C

21. EN 16952:2018Agricultural machinery —Rough-terrain WorkPlatforms for Orchard'soperations (WPO) – Safety

C

22. EN 17059:2018Plating and anodizinglines — Safety requirements

C

23. EN ISO 19085-4:2018Woodworking machines —Safety — Part 4:Vertical panel circularsawing machines(ISO 19085-4:2018)

C

24. EN ISO 19085-6:2017Woodworking machines —Safety — Part 6: Singlespindle vertical mouldingmachines (‘toupies’) (ISO19085-6:2017)

C

25. EN ISO 19085-8:2018Woodworking machines —Safety — Part 8: Belt sandingand calibrating machines forstraight workpieces (ISO19085-8:2017)

C

26. EN ISO 19225:2017Underground miningmachines — Mobileextracting machines at theface — Safety requirementsfor shearer loaders and

C

Page 8: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

8 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

plough systems (ISO19225:2017)

27. EN ISO 28927-2:2009Hand-held portable powertools — Test methods forevaluation of vibrationemission — Part 2:Wrenches, nutrunnersand screwdrivers (ISO28927-2:2009)EN ISO 28927-2:2009/A1:2017

C

28. EN ISO/IEC 80079-38:2016Explosive atmospheres —Part 38: Equipmentand components inexplosive atmospheres inunderground mines (ISO/IEC80079-38:2016)EN ISO/IEC 80079-38:2016/A1:2018

C

29. EN 50569:2013Household and similarelectrical appliances —Safety — Particularrequirements for commercialelectric spin extractorsEN 50569:2013/A1:2018

C

30. EN 50570:2013Household and similarelectrical appliances —Safety — Particularrequirements for commercialelectric tumble dryersEN 50570:2013/A1:2018

C

31. EN 50571:2013Household and similarelectrical appliances —Safety — Particularrequirements for commercialelectric washing machinesEN 50571:2013/A1:2018

C

32. EN 50636-2-107:2015Safety of household andsimilar appliances —Part 2-107: Particularrequirements for roboticbattery powered electricallawnmowers (IEC60335-2-107:2012 Modified)

C

Page 9: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

9

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

EN 50636-2-107:2015/A1:2018

33. EN 60335-1:2012Household and similarelectrical appliances —Safety — Part 1:General requirements(IEC 60335-1:2010Modified)EN 60335-1:2012/A11:2014EN 60335-1:2012/A13:2017

C

34. EN 60335-2-58:2005Household and similarelectrical appliances —Safety — Part 2-58:Particular requirementsfor commercial electricdishwashing machines (IEC60335-2-58:2002 Modified)EN 60335-2-58:2005/A2:2015EN 60335-2-58:2005/A12:2016

C

[F135. EN 62841-2-1:2018Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery – Safety – Part2-1: Particular requirementsfor hand-held drillsand impact drills (IEC62841-2-1:2017, Modified)EN 62841-2-1:2018/A11:2019

C]

36. EN 62841-2-17:2017Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery — Safety — Part2-17: Particular requirementsfor hand-held routers(IEC 62841-2-17:2017Modified)

C

37. EN 62841-3-1:2014Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery — Safety — Part3-1: Particular requirementsfor transportable table saws

C

Page 10: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

10 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

(IEC 62841-3-1:2014,modified)EN 62841-3-1:2014/A11:2017

38. EN 62841-3-4:2016Electric motor-operatedhand-held tools, transportabletools and lawn andgarden machinery —Safety — Part 3-4:Particular requirements fortransportable bench grinders(IEC 62841-3-4:2016Modified)EN 62841-3-4:2016/A11:2017

C

39. EN 62841-3-6:2014Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery — Safety — Part3-6: Particular requirementsfor transportable diamonddrills with liquid system (IEC62841-3-6:2014, modified)EN 62841-3-6:2014/A11:2017

C

40. EN 62841-3-9:2015Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery — Safety — Part3-9: Particular requirementsfor transportable mitresaws (IEC 62841-3-9:2014Modified)EN 62841-3-9:2015/A11:2017

C

41. EN 62841-3-10:2015Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery — Safety — Part3-10: Particular requirementsfor transportablecut-off machines(IEC 62841-3-10:2015Modified)EN 62841-3-10:2015/A11:2017

C

Page 11: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

11

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

42. EN 62841-3-14:2017Electric motor-operatedhand-held tools, transportabletools and lawn andgarden machinery —Safety — Part 3-14:Particular requirements fortransportable drain cleaners(IEC 62841-3-14:2017Modified)

C

[F243. EN ISO 18497:2018Agricultural machineryand tractors – Safety ofhighly automated agriculturalmachines – Principles fordesign (ISO 18497:2018)

B

44. EN ISO 19353:2019Safety of machinery – Fireprevention and fire protection(ISO 19353:2019)

B

45. EN 707:2018Agricultural machinery –Slurry tankers – Safety

C

46. EN 1459-2:2015+A1:2018Rough-terrain trucks – Safetyrequirements and verification– Part 2: Slewing variable-reach trucks

C

47. EN ISO 3691-5:2015Industrial trucks – Safetyrequirements and verification– Part 5: Pedestrian-propelledtrucks (ISO 3691-5:2014)

C

48. EN ISO 4254-9:2018Agricultural machinery –Safety – Part 9: Seed drills(ISO 4254-9:2018)

C

49. EN ISO 10517:2019Powered hand-held hedgetrimmers – Safety (ISO10517:2019)

C

50. EN ISO 11148-13:2018Hand-held non-electric powertools – Safety requirements– Part 13: Fastener drivingtools (ISO 11148-13:2017)

C

51. EN 12012-1:2018 C

Page 12: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

12 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Plastics and rubber machines– Size reduction machines –Part 1: Safety requirementsfor blade granulators andshredders

52. EN 12312-8:2018Aircraft ground supportequipment – Specificrequirements – Part 8:Maintenance or service stairsand platforms

C

53. EN 12733:2018Agricultural and forestrymachinery – Pedestriancontrolled motor mowers –Safety

C

54. EN 14033-4:2019Railway applications – Track– Railbound construction andmaintenance machines – Part4: Technical requirementsfor running, travelling andworking on urban rail

C

55. EN 16712-4:2018Portable equipment forprojecting extinguishingagents supplied byfirefighting pumps – Portablefoam equipment – Part4: High expansion foamgenerators PN16

C

56. EN 16770:2018Safety of woodworkingmachines – Chip and dustextraction systems forindoor installation – Safetyrequirements

C

57. EN 16985:2018Spray booths for organiccoating material – Safetyrequirements

C

58. EN 17067:2018Forestry machinery – Safetyrequirements on radio remotecontrols

C

59. EN ISO 19296:2018Mining – Mobile machinesworking underground

C

Page 13: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

13

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

– Machine safety (ISO19296:2018)

60. EN ISO 28927-4:2010Hand-held portable powertools – Test methods forevaluation of vibrationemission – Part 4: Straightgrinders (ISO 28927-4:2010)EN ISO 28927-4:2010/A1:2018

C

61. EN 60204-1:2018Safety of machinery –Electrical equipmentof machines – Part 1:General requirements (IEC60204-1:2016, Modified)

B

62. EN IEC 60204-11:2019Safety of machinery –Electrical equipmentof machines – Part 11:Requirements for equipmentfor voltages above 1 000V AC or 1 500 V DC andnot exceeding 36 kV (IEC60204-11:2018)

B

63. EN 62841-4-2:2019Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery – Safety – Part4-2: Particular requirementsfor hedge trimmers (IEC62841-4-2:2017, Modified)

C

64. EN 62841-3-12:2019Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery – Safety – Part3-12: Particular requirementsfor transportablethreading machines (IEC62841-3-12:2017)

C

65. EN 62841-2-21:2019Electric motor-operatedhand-held tools, transportabletools and lawn and gardenmachinery – Safety – Part2-21: Particular requirementsfor hand-held drain cleaners

C

Page 14: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

14 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

(IEC 62841-2-21:2017,Modified)

66. EN ISO 20607:2019Safety of machinery –Instruction handbook –General drafting principles(ISO 20607:2019)

B

67. EN ISO 19085-7:2019Woodworking machines– Safety – Part 7: Surfaceplaning, thickness planing,combined surface/thicknessplaning machines (ISO19085-7:2019)

C

68. EN 1114-3:2019Plastics and rubber machines– Extruders and extrusionlines – Part 3: Safetyrequirements for haul-offs

C

69. EN 1127-1:2019Explosive atmospheres –Explosion prevention andprotection – Part 1: Basicconcepts and methodology

B]

Textual AmendmentsF1 Substituted by Commission Implementing Decision (EU) 2020/480 of 1 April 2020 amending

Implementing Decision (EU) 2019/436 on harmonised standards for machinery drafted in support ofDirective 2006/42/EC of the European Parliament and of the Council.

F2 Inserted by Commission Implementing Decision (EU) 2020/480 of 1 April 2020 amending ImplementingDecision (EU) 2019/436 on harmonised standards for machinery drafted in support of Directive 2006/42/EC of the European Parliament and of the Council.

ANNEX II

No Reference of the standard Type1. EN 474-1:2006+A5:2018

Earth-moving machinery —Safety — Part 1: GeneralrequirementsNotice: This publicationdoes not concern clause 5.8.1Visibility — Operator's fieldof view of this standard,but only in relation withEN 474-5:2006+A3:2013

C

Page 15: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

15

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

requirements for hydraulicexcavators, the applicationof which does not confer apresumption of conformityto the essential health andsafety requirements 1.2.2 and3.2.1 of Annex I to Directive2006/42/EC.

2. EN 13241:2003+A2:2016Industrial, commercial,garage doors and gates —Product standard,performance characteristicsNotice: With regard toparagraphs 4.2.2, 4.2.6,4.3.2, 4.3.3, 4.3.4, 4.3.6,this publication does notconcern the reference to EN12453:2000, the applicationof which does not confer apresumption of conformity tothe essential health and safetyrequirements 1.3.7 and 1.4.3of Annex I to Directive2006/42/EC.

C

[F33. EN ISO 19085-3:2017Woodworking machines –Safety requirements – Part 3:Numerically controlled (NC)boring and routing machinesNotice: With regard toits point 6.6.2.2.3.1, theharmonised standard ENISO 19085-3:2017 doesnot confer a presumptionof conformity with theessential health and safetyrequirement set out in point1.4.1 of Annex I to Directive2006/42/EC, which requiresthat guards and protectivedevices must not be easy toby-pass.

C]

Textual AmendmentsF3 Inserted by Commission Implementing Decision (EU) 2019/1766 of 23 October 2019 amending

Implementing Decision (EU) 2019/436 as regards harmonised standard EN ISO 19085-3:2017 fornumerically controlled boring and routing machines.

Page 16: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

16 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

[F4ANNEX III

Textual AmendmentsF4 Substituted by Commission Implementing Decision (EU) 2019/1863 of 6 November 2019 amending and

correcting Implementing Decision (EU) 2019/436 as regards the withdrawal of references of harmonisedstandards for machinery from the Official Journal of the European Union (Text with EEA relevance).

No Reference ofstandard

Date ofwithdrawal

Type

1. EN1037:1995+A1:2008Safety ofmachinery —Prevention ofunexpected start-up

19 September 2020 B

2. EN474-1:2006+A4:2013Earth-movingmachinery —Safety — Part 1:General requirementsNotice: Thispublication doesnot concern clause5.8.1 Visibility —Operator’s field ofview of this standard,the application ofwhich does notconfer a presumptionof conformity to theessential health andsafety requirements1.2.2 and 3.2.1 ofAnnex I to Directive2006/42/EC.

19 September 2020 C

3. EN1853:1999+A1:2009Agriculturalmachinery — Trailerswith tipping body –Safety

19 September 2020 C

4. EN1870-6:2002+A1:2009Safety ofwoodworkingmachines — Circularsawing machines —

19 September 2020 C

Page 17: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

17

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Part 6: Circularsawing machinesfor firewood anddual purpose circularsawing machines forfirewood/circularsaw benches, withmanual loading and/or unloading

5. EN ISO 4254-5:2009Agriculturalmachinery —Safety — Part 5:Power-driven soil-working machines(ISO 4254-5:2008)

19 September 2020 C

6. EN ISO 4254-7:2009Agriculturalmachinery —Safety — Part 7:Combine harvesters,forage harvestersand cotton harvesters(ISO 4254-7:2008)

19 September 2020 C

7. EN14017:2005+A2:2009Agricultural andforestry machinery —Solid fertilizerdistributors – Safety

19 September 2020 C

8. EN ISO 5395-1:2013Garden equipment —Safety requirementsfor combustion-engine-poweredlawnmowers — Part1: Terminology andcommon tests (ISO5395-1:2013)

19 September 2020 C

9. EN ISO 5395-3:2013Garden equipment —Safety requirementsfor combustion-engine-poweredlawnmowers —Part 3: Ride-onlawnmowers withseated operator (ISO5395-3:2013)

19 September 2020 C

Page 18: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

18 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

EN ISO 5395-3:2013/A1:2017

10. EN12013:2000+A1:2008Plastics and rubbermachines — Internalmixers — Safetyrequirements

19 September 2020 C

11. EN12999:2011+A1:2012Cranes — Loadercranes

19 September 2020 C

12. EN13001-3-1:2012+A1:2013Cranes — GeneralDesign — Part 3-1:Limit States andproof competence ofsteel structure

19 September 2020 C

13. EN 13135:2013Cranes — Safety —Design —Requirements forequipment

19 September 2020 C

14. EN13684:2004+A3:2009Garden equipment —Pedestrian controlledlawn aerators andscarifiers – Safety

19 September 2020 C

15. EN 15895:2011Cartridge operatedhand-heldtools — Safetyrequirements —Fixing and hardmarking tools

19 September 2020 C

16. EN692:2005+A1:2009Machine tools —Mechanicalpresses — Safety

19 September 2021 C

17. EN693:2001+A2:2011Machine tools —Safety — Hydraulicpresse

19 March 2021 C

Page 19: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

19

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

18. EN13736:2003+A1:2009Safety of machinetools — Pneumaticpresses

19 September 2021 C

19. EN848-1:2007+A2:2012Safety ofwoodworkingmachines — One sidemoulding machineswith rotating tool —Part 1: Single spindlevertical mouldingmachines

19 September 2020 C

20. EN1710:2005+A1:2008Equipment andcomponentsintended for use inpotentially explosiveatmospheres inunderground mines

19 September 2020 C

21. EN 50569:2013Household andsimilar electricalappliances —Safety — Particularrequirements forcommercial electricspin extractors

12 January 2021 C

22. EN 50570:2013Household andsimilar electricalappliances —Safety — Particularrequirements forcommercial electrictumble dryers

12 January 2021 C

23. EN 50571:2013Household andsimilar electricalappliances —Safety — Particularrequirements forcommercial electricwashing machines

12 January 2021 C

24. EN50636-2-107:2015

12 January 2020 C

Page 20: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

20 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Safety of householdand similarappliances — Part2-107: Particularrequirements forrobotic batterypowered electricallawnmowers (IEC60335-2-107:2012Modified)

25. EN 60335-1:2012Household andsimilar electricalappliances —Safety — Part 1:General requirements(IEC 60335-1:2010Modified)EN 60335-1:2012/A11:2014

3 May 2020 C

26. EN 60745-2-1:2010Hand-held motor-operated electrictools — Safety —Part 2-1: Particularrequirementsfor drills andimpact drills (IEC60745-2-1:2003Modified + A1:2008)

19 January 2022 C

27. EN 60745-2-17:2010Hand-held motor-operated electrictools — Safety —Part 2-17: Particularrequirementsfor routers andtrimmers (IEC60745-2-17:2010Modified)

15 December 2021 C

28. EN 62841-3-1:2014Electric motor-operated hand-heldtools, transportabletools and lawn andgarden machinery —Safety — Part3-1: Particularrequirements fortransportabletable saws (IEC

19 October 2019 C

Page 21: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

21

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

62841-3-1:2014,modified)

29. EN 61029-2-4:2011Safety oftransportablemotor-operatedelectric tools —Part 2-4: Particularrequirements forbench grinders (IEC61029-2-4:1993Modified + A1:2001Modified)

24 June 2020 C

30. EN 62841-3-6:2014Electric motor-operated hand-heldtools, transportabletools and lawn andgarden machinery —Safety — Part3-6: Particularrequirements fortransportablediamond drills withliquid system (IEC62841-3-6:2014,modified)

19 October 2019 C

31. EN 62841-3-9:2015Electric motor-operated hand-heldtools, transportabletools and lawn andgarden machinery —Safety — Part3-9: Particularrequirements fortransportablemitre saws (IEC62841-3-9:2014Modified)

15 November 2019 C

32. EN 62841-3-10:2015Electric motor-operated hand-heldtools, transportabletools and lawn andgarden machinery —Safety — Part3-10: Particularrequirements fortransportable cut-off machines (IEC

19 October 2019 C

Page 22: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

22 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

62841-3-10:2015Modified)

33. EN13241:2003+A2:2016Industrial,commercial, garagedoors and gates —Product standard,performancecharacteristics

19 September 2020 C

34. EN786:1996+A2:2009Garden equipment —Electrically poweredwalk- behind andhand-held lawntrimmers and lawnedge trimmers —Mechanical safety

19 September 2020 C

35. EN1870-14:2007+A2:2012Safety ofwoodworkingmachines — Circularsawing machines —Part 14: Verticalpanel sawingmachines

19 September 2020 C

36. EN 61496-1:2013Safety ofmachinery —Electro-sensitiveprotectiveequipment — Part 1:General requirementsand tests

19 September 2020 C

37. EN ISO 11200:2014Acoustics — Noiseemitted by machineryand equipment —Guidelines for theuse of basic standardsfor the determinationof emission soundpressure levels ata work station andat other specifiedpositions

19 September 2020 B

38. EN1870-13:2007+A2:2012

19 September 2020 C

Page 23: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

23

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Safety ofwoodworkingmachines — Circularsawing machines —Part 13: Horizontalbeam panel sawingmachines

[F239. EN ISO28927-4:2010Hand-held portablepower tools –Test methodsfor evaluation ofvibration emission– Part 4: Straightgrinders (ISO28927-4:2010)

2 April 2020 C

40. EN ISO 19353:2016Safety of machinery– Fire prevention andfire protection (ISO19353:2015)

2 October 2021 B

41. EN707:1999+A1:2009Agriculturalmachinery – Slurrytankers – Safety

2 October 2021 C

42. EN792-13:2000+A1:2008Hand-held non-electric power tools –Safety requirements– Part 13: Fastenerdriving tools

2 October 2021 C

43. EN 1889-1:2011Machines forunderground mines– Mobile machinesworking underground– Safety – Part 1:Rubber tyred vehicles

2 October 2021 C

44. EN ISO 3691-5:2014Industrial trucks –Safety requirementsand verification –Part 5: Pedestrian-propelled trucks (ISO3691-5:2014)

2 October 2021 C

Page 24: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

24 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

EN ISO 3691-5:2014/AC:2014

45. EN ISO 10517:2009Powered hand-heldhedge trimmers– Safety (ISO10517:2009)EN ISO 10517:2009/A1:2013

2 October 2021 C

46. EN12012-1:2007+A1:2008Plastics and rubbermachines – Sizereduction machines– Part 1: Safetyrequirements forblade granulators

2 October 2021 C

47. EN12012-3:2001+A1:2008Plastics and rubbermachines – Sizereduction machines– Part 3: Safetyrequirements forshredders

2 October 2021 C

48. EN12312-8:2005+A1:2009Aircraft groundsupport equipment –Specific requirements– Part 8: Maintenancestairs and platforms

2 October 2021 C

49. EN12733:2001+A1:2009Agricultural andforestry machinery –Pedestrian controlledmotor mowers –Safety

2 October 2021 C

50. EN12981:2005+A1:2009Coating plants –Spray booths forapplication of organicpowder coatingmaterial – Safetyrequirements

2 October 2021 C

51. EN13355:2004+A1:2009

2 October 2021 C

Page 25: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

25

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

Coating plants –Combined booths –Safety requirements

52. EN14018:2005+A1:2009Agricultural andforestry machinery –Seed drills – Safety

2 October 2021 C

53. EN 60204-1:2006Safety of machinery– Electricalequipment ofmachines – Part 1:General requirements(IEC 60204-1:2005,Modified)EN 60204-1:2006/AC:2010EN 60204-1:2006/A1:2009

2 October 2021 B

54. EN 60204-11:2000Safety of machinery– Electricalequipment ofmachines – Part11: Requirementsfor HV equipmentfor voltages above1 000 V a.c. or 1500 V d.c. and notexceeding 36 kV(IEC 60204-11:2000)EN 60204-11:2000/AC:2010

2 October 2021 B

55. EN 848-3:2012Safety ofwoodworkingmachines – One sidemoulding machineswith rotating tool –Part 3: Numericallycontrolled (NC)boring and routingmachines

2 October 2021 C

56. EN ISO28927-2:2009Hand-held portablepower tools –Test methodsfor evaluation of

2 October 2021 C

Page 26: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

26 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

vibration emission– Part 2: Wrenches,nutrunners andscrewdrivers (ISO28927-2:2009)

57. EN 60745-2-21:2009Hand-held motor-operated electrictools – Safety –Part 2-21: Particularrequirements fordrain cleaners (IEC60745-2-21:2002,Modified)EN 60745-2-21:2009/A1:2010

2 October 2021 C

58. EN859:2007+A2:2012Safety ofwoodworkingmachines – Handfed surface planingmachines

2 October 2021 C

59. EN860:2007+A2:2012Safety ofwoodworkingmachines – One sidethickness planingmachines

2 October 2021 C

60. EN861:2007+A2:2012Safety ofwoodworkingmachines –Surface planingand thicknessingmachines

2 October 2021 C

61. EN1114-3:2001+A1:2008Plastics and rubbermachines – Extrudersand extrusion lines– Part 3: Safetyrequirements forhaul-offs

2 October 2021 C

62. EN 1127-1:2011Explosiveatmospheres –Explosion prevention

2 October 2021 B

Page 27: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

27

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in forceon or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have been

made appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

and protection – Part1: Basic concepts andmethodology

63. EN 1459-2:2015Rough-terrain trucks– Safety requirementsand verification– Part 2: Slewingvariable-reach trucks

2 October 2021 C]]

Page 28: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

28 Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...

Document Generated: 2020-12-28Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known to be in force

on or before 28 December 2020. There are changes that may be brought into force at a future date. Changes that have beenmade appear in the content and are referenced with annotations. (See end of Document for details) View outstanding changes

(1) OJ L 316, 14.11.2012, p. 12.(2) OJ L 157, 9.6.2006, p. 24.(3) Directive 98/37/EC of the European Parliament and of the Council of 22 June 1998 on the

approximation of the laws of the Member States relating to machinery (OJ L 207, 23.7.1998, p. 1).(4) Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market ofelectrical equipment designed for use within certain voltage limits (OJ L 96, 29.3.2014, p. 357).

(5) Directive 95/16/EC of the European Parliament and of the Council of 29 June 1995 on theapproximation of the laws of the Member States relating to lifts (OJ L 213, 7.9.1995, p. 1).

(6) Commission Implementing Decision (EU) 2015/27 of 7 January 2015 on the publication witha restriction in the Official Journal of the European Union of the reference of standard EN474-1:2006+A4:2013 on Earth-moving machinery under Directive 2006/42/EC of the EuropeanParliament and of the Council (OJ L 4, 8.1.2015, p. 24).

(7) Commission Implementing Decision (EU) 2015/1301 of 20 July 2015 on the publication witha restriction in the Official Journal of the European Union of the reference of standard EN13241-1:2003+A1:2011 on industrial, commercial and garage doors and gates under Directive2006/42/EC of the European Parliament and of the Council (OJ L 199, 29.7.2015, p. 40).

(8) OJ C 92, 9.3.2018, p. 1.

Page 29: Commission Implementing Decision (EU) 2019/436 of 18 …Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standards for... Document Generated: 2020-12-28

Commission Implementing Decision (EU) 2019/436 of 18 March 2019 on the harmonised standardsfor...Document Generated: 2020-12-28

29

Changes to legislation: Commission Implementing Decision (EU) 2019/436 is up to date with all changes known tobe in force on or before 28 December 2020. There are changes that may be brought into forceat a future date. Changes that have been made appear in the content and are referenced withannotations.View outstanding changes

Changes and effects yet to be applied to :– Recital 14 replacement by EUDN 2019/1863 Decision