CO2 Car Specifications Rules and Regulations 2013-2014.
-
Upload
barnaby-warren -
Category
Documents
-
view
221 -
download
2
Transcript of CO2 Car Specifications Rules and Regulations 2013-2014.
![Page 1: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/1.jpg)
CO2 Car Specifications
Rules and Regulations 2013-2014
![Page 2: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/2.jpg)
Dragster Body
DB1: One (1)-piece, all-wood construction. Any type of lamination will result in disqualification. Two (2) or more like or unlike pieces of wood glued together are not considered one (1)-piece, all-wood construction. No add-ons such as body strengtheners, fenders, plastic canopy, exhausts, or air foils may be attached to or enclosed within the vehicle. Fiberglass and shrink wrap are considered body strengtheners and cannot be used on the car body for any reason. Decals may be used for decoration only. They may not be used to gain an aerodynamic advantage, i.e., decals cannot cover the exterior axle holes or be used to cover open areas of the body.
![Page 3: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/3.jpg)
Dragster Body Length
DB2: Min 200mm Max 305mm
![Page 4: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/4.jpg)
Dragster Body Height with Wheels
DB3: Max 75mm
![Page 5: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/5.jpg)
Dragster Body Mass (without Co2)
DB4: Min 45 G Max 55 G
![Page 6: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/6.jpg)
Dragster Body Width at Axles Front & Back
DB5: Min 35mm Max 42mm
![Page 7: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/7.jpg)
Dragster Vehicle Total Width (including Wheels)
DB6: Max 90mm
- -90mm
![Page 8: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/8.jpg)
Axle per Car
A1: Dragster must have two (2) axles per car, no more.
![Page 9: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/9.jpg)
Axle Hole (Position above the bottom of the Car)
A2: Min 5mm Max 10mm
5-10mm
![Page 10: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/10.jpg)
Axle Hole From front and Rear of Car
A3: Min 9mm Max 100mm
![Page 11: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/11.jpg)
Wheelbase
A4: Min 105mm Max 270mm
![Page 12: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/12.jpg)
Bearing Bushing and Lubricants
A5: Bearings, bushing and lubricants may be used
![Page 13: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/13.jpg)
Spacer Washer
S1: Spacer Washer, Maximum: 10
![Page 14: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/14.jpg)
Power Plant Hole
The power plant hole must be at the farthest point at the rear of the car and must be drilled parallel to the racing surface to assure proper puncture of the CO2 cartridge. A minimum of 3mm thickness around the entire power plant hole must be maintained for safety. DO NOT PAINT INSIDE THE CO2 CARTRIDGE HOLE.
![Page 15: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/15.jpg)
Power Plant Hole Depth
P2: Min 45 mm Max 55 mm
45mm – 55 mm
![Page 16: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/16.jpg)
Power Plant Housing Thickness
P3: Min 3mm
![Page 17: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/17.jpg)
Power Plant Chamber Diameter
P4: Min 19mm Max 20mm
min.
20mm max.
![Page 18: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/18.jpg)
Chamber Diameter to Race Surface
P5: Lowest point of chamber diameter to race surface (With Wheels) 26mm – 40mm
26mm – 40mm
![Page 19: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/19.jpg)
Screw Eye Inside Diameter
ES2: Min 3mm Max 5mm
3-5mm
![Page 20: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/20.jpg)
Screw Eye Distance Apart
ES3: Min 150mm Max 270mm
150mm-270mm
![Page 21: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/21.jpg)
Wheels
W1: A dragster must have exactly four (4) wheels, each of which separately must meet the regulations in W2 and W3 below. All four (4) wheels must touch the racing surface at the same time. All wheels must roll. Wheels must be made entirely from plastic. Dimensions must be consistent for the full circumference of the wheel.
![Page 22: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/22.jpg)
Wheels
All wheels must be located on the exterior of the body.
![Page 23: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/23.jpg)
Wheels Diameter
W2: Min 30mm Max 40mm
![Page 24: CO2 Car Specifications Rules and Regulations 2013-2014.](https://reader036.fdocuments.us/reader036/viewer/2022062408/56649f305503460f94c4ab48/html5/thumbnails/24.jpg)
Wheels Width
W3: Min 2mm Max 18mm
2mm-18mm
2mm-18mm