CLD-DS130 Rev 0H Cree XLamp XHP35 LEDs - LEDSupply
Transcript of CLD-DS130 Rev 0H Cree XLamp XHP35 LEDs - LEDSupply
11
Product family data sheet
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
Cree, Inc.4600 Silicon Drive
Durham, NC 27703USA Tel: +1.919.313.5300
WW
W.C
REE.
Co
m/X
LAm
pC
LD-D
S130 Rev
0H
Cree® XLamp® XHP35 LEDs
ProDuCt DEsCriPtion
The XLamp® XHP35 LeD brings the
performance of Cree’s extreme High
Power LeDs to the XP footprint, setting a
new standard for performance delivered
by a 3.45 x 3.45 mm LED. Leveraging the
breakthrough 12-v monolithic power die
built on Cree’s innovative architecture and
uniquely enabled by the SC5 Technology™
Platform, the XHP35 LeD allows the
use of readily available cost--optimized
drivers to unleash the capabilities of
Cree’s high-power LeDs. Available in both
high-density and high-intensity versions,
the XHP35 LeD is application optimized
to enable new designs and radically lower
system costs.
FEAturEs
• Available in white in high-density and
high-intensity versions for design
flexibility
• XHP35 High Intensity LeD is
optimized to deliver maximum
candela through secondary optics
• Available in 5-step easyWhite® bins
at 2700 K to 5700 K CCT and 3-step
EasyWhite bins at 2700 K to 3500 K
CCT
• Available in ANSI white bins at
2700 K to 7000 K CCT
• Available in standard, 70-, 80-, 85-
and 90-minimum CRI options
• Binned at 85 °C
• Maximum drive current: 1050 mA
• Low thermal resistance: 1.8 °C/W
• Wide viewing angle: 115° for high
intensity, 125° for high density
• Unlimited floor life at
≤ 30 ºC/85% RH
• Reflow solderable - JEDEC
J-STD-020C
• RoHS-compliant
• UL® recognized component
(e349212)
tAbLE oF ContEnts
Characteristics ..............................................2
Flux Characteristics, High Density
easyWhite® Order Codes and Bins ...............3
Flux Characteristics, High Density ANSI
White Order Codes and Bins ........................6
Flux Characteristics, High Intensity
easyWhite® Order Codes and Bins ............ 10
Flux Characteristics, High Intensity ANSI
White Order Codes and Bins ..................... 13
Relative Spectral Power Distribution ........ 17
Relative Flux vs. Junction Temperature .... 17
electrical Characteristics ........................... 18
Relative Flux vs. Current ............................ 18
Relative Chromaticity vs. Current .............. 19
Relative Chromaticity vs. Temperature ..... 20
Typical Spatial Distribution ........................ 21
Thermal Design .......................................... 22
Performance Groups – Luminous Flux..... 22
Performance Groups – Chromaticity ........ 23
Cree’s easyWhite® Chromaticity Regions
Plotted on the 1931 CIe Curve .................. 26
Cree’s Standard Cool White Kits Plotted
on ANSI Standard Chromaticity Regions .. 29
Cree’s Standard Warm and Neutral White
Kits Plotted on ANSI Standard
Chromaticity Regions ................................ 30
Bin and Order Code Formats ..................... 31
Reflow Soldering Characteristics .............. 32
Notes .......................................................... 33
Mechanical Dimensions ............................ 34
Tape and Reel ............................................. 36
Packaging ................................................... 38
XHP35 High Density LED XHP35 High intensity LED
22
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
2
XLamp® XHp35 LED
CHArACtEristiCs
Characteristics unit Minimum typical Maximum
Thermal resistance, junction to solder point °C/W 1.8
viewing angle (FWHM) - High Density degrees 125
viewing angle (FWHM) - High Intensity degrees 115
Temperature coefficient of voltage mV/°C -8
eSD withstand voltage (HBM per Mil-Std-883D) v 8000
DC forward current mA 1050
Reverse voltage v -5
Forward voltage (@ 350 mA, 85 °C) v 11.3 11.9
LeD junction temperature °C 150
33
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
3
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
FLuX CHArACtEristiCs, HigH DEnsity EAsyWHitE® orDEr CoDEs AnD bins (tJ = 85 °C)
The following table provides order codes for XLamp XHP35 High Density LEDs. For a complete description of how the flux and chromaticity
groups are reflected in the bin code and order code nomenclature, please see the Bin and Order Code Formats section (page 31).
nominalCCt
Cri Minimum Luminous Flux @350 mA 3-step 5-step
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* group order Code group order Code
5700 K
70
e4 635 717
57e
XHP35A-00-0000-0D0Be457e
e2 590 666 XHP35A-00-0000-0D0Be257e
D4 550 621 XHP35A-00-0000-0D0BD457e
80D4 550 621
57eXHP35A-00-0000-0D0HD457e
D2 510 576 XHP35A-00-0000-0D0HD257e
85
C4 475 536
57e
XHP35A-00-0000-0D0PC457e
C2 440 497 XHP35A-00-0000-0D0PC257e
B4 410 463 XHP35A-00-0000-0D0PB457e
90
C4 475 536
57e
XHP35A-00-0000-0D0UC457e
C2 440 497 XHP35A-00-0000-0D0UC257e
B4 410 463 XHP35A-00-0000-0D0UB457e
5000 K
70
e4 635 717
50e
XHP35A-00-0000-0D0Be450e
e2 590 666 XHP35A-00-0000-0D0Be250e
D4 550 621 XHP35A-00-0000-0D0BD450e
80D4 550 621
50eXHP35A-00-0000-0D0HD450e
D2 510 576 XHP35A-00-0000-0D0HD250e
85
C4 475 536
50e
XHP35A-00-0000-0D0PC450e
C2 440 497 XHP35A-00-0000-0D0PC250e
B4 410 463 XHP35A-00-0000-0D0PB450e
90
C4 475 536
50e
XHP35A-00-0000-0D0UC450e
C2 440 497 XHP35A-00-0000-0D0UC250e
B4 410 463 XHP35A-00-0000-0D0UB450e
44
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
4
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nominalCCt
Cri Minimum Luminous Flux @350 mA 3-step 5-step
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* group order Code group order Code
4500 K
70e2 590 666
45eXHP35A-00-0000-0D0Be245e
D4 550 621 XHP35A-00-0000-0D0BD445e
80D4 550 621
45eXHP35A-00-0000-0D0HD445e
D2 510 576 XHP35A-00-0000-0D0HD245e
85C2 440 497
45eXHP35A-00-0000-0D0PC245e
B4 410 463 XHP35A-00-0000-0D0PB445e
90C2 440 497
45eXHP35A-00-0000-0D0UC245e
B4 410 463 XHP35A-00-0000-0D0UB445e
4000 K
70
e2 590 666
40e
XHP35A-00-0000-0D0Be240e
D4 550 621 XHP35A-00-0000-0D0BD440e
D2 510 576 XHP35A-00-0000-0D0BD240e
80D4 550 621
40eXHP35A-00-0000-0D0HD440e
D2 510 576 XHP35A-00-0000-0D0HD240e
85C2 440 497
40eXHP35A-00-0000-0D0PC240e
B4 410 463 XHP35A-00-0000-0D0PB440e
90C2 440 497
40eXHP35A-00-0000-0D0UC240e
B4 410 463 XHP35A-00-0000-0D0UB440e
3500 K
70
e2 590 666
35e
XHP35A-00-0000-0D0Be235e
D4 550 621 XHP35A-00-0000-0D0BD435e
D2 510 576 XHP35A-00-0000-0D0BD235e
80
D4 550 621
35G
XHP35A-00-0000-0D0HD435G
35e
XHP35A-00-0000-0D0HD435e
D2 510 576 XHP35A-00-0000-0D0HD235G XHP35A-00-0000-0D0HD235e
C4 475 536 XHP35A-00-0000-0D0HC435G XHP35A-00-0000-0D0HC435e
85C2 440 497
35GXHP35A-00-0000-0D0PC235G
35eXHP35A-00-0000-0D0PC235e
B4 410 463 XHP35A-00-0000-0D0PB435G XHP35A-00-0000-0D0PB435e
90C2 440 497
35GXHP35A-00-0000-0D0UC235G
35eXHP35A-00-0000-0D0UC235e
B4 410 463 XHP35A-00-0000-0D0UB435G XHP35A-00-0000-0D0UB435e
FLuX CHArACtEristiCs, HigH DEnsity EAsyWHitE® orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
55
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
5
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nominalCCt
Cri Minimum Luminous Flux @350 mA 3-step 5-step
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* group order Code group order Code
3000 K
70D4 550 621
30eXHP35A-00-0000-0D0BD430e
D2 510 576 XHP35A-00-0000-0D0BD230e
80D2 510 576
30GXHP35A-00-0000-0D0HD230G
30eXHP35A-00-0000-0D0HD230e
C4 475 536 XHP35A-00-0000-0D0HC430G XHP35A-00-0000-0D0HC430e
85
C2 440 497
30G
XHP35A-00-0000-0D0PC230G
30e
XHP35A-00-0000-0D0PC230e
B4 410 463 XHP35A-00-0000-0D0PB430G XHP35A-00-0000-0D0PB430e
B2 380 429 XHP35A-00-0000-0D0PB230G XHP35A-00-0000-0D0PB230e
90
C2 440 497
30G
XHP35A-00-0000-0D0UC230G
30e
XHP35A-00-0000-0D0UC230e
B4 410 463 XHP35A-00-0000-0D0UB430G XHP35A-00-0000-0D0UB430e
B2 380 429 XHP35A-00-0000-0D0UB230G XHP35A-00-0000-0D0UB230e
2700 K
80C4 475 536
27GXHP35A-00-0000-0D0HC427G
27eXHP35A-00-0000-0D0HC427e
C2 440 497 XHP35A-00-0000-0D0HC227G XHP35A-00-0000-0D0HC227e
85B4 410 463
27GXHP35A-00-0000-0D0PB427G
27eXHP35A-00-0000-0D0PB427e
B2 380 429 XHP35A-00-0000-0D0PB227G XHP35A-00-0000-0D0PB227e
90B4 410 463
27GXHP35A-00-0000-0D0UB427G
27eXHP35A-00-0000-0D0UB427e
B2 380 429 XHP35A-00-0000-0D0UB227G XHP35A-00-0000-0D0UB227e
FLuX CHArACtEristiCs, HigH DEnsity EAsyWHitE® orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
66
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
6
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
FLuX CHArACtEristiCs, HigH DEnsity Ansi WHitE orDEr CoDEs AnD bins (tJ = 85 °C)
The following table provides order codes for XLamp XHP35 LEDs. For a complete description of how the flux and chromaticity groups are
reflected in the bin code and order code nomenclature, please see the Bin and Order Code Formats section (page 31).
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
7000 K
0A, 0B, 0C, 0D, 0R, 0S, 0T, 0U, 1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U
0 68
e4 635 717 XHP35A-00-0000-0D00e40DT
e2 590 666 XHP35A-00-0000-0D00e20DT
D4 550 621 XHP35A-00-0000-0D00D40DT
70
e4 635 717 XHP35A-00-0000-0D0Be40DT
e2 590 666 XHP35A-00-0000-0D0Be20DT
D4 550 621 XHP35A-00-0000-0D0BD40DT
80D4 550 621 XHP35A-00-0000-0D0HD40DT
D2 510 576 XHP35A-00-0000-0D0HD20DT
85
C4 475 536 XHP35A-00-0000-0D0PC40DT
C2 440 497 XHP35A-00-0000-0D0PC20DT
B4 410 463 XHP35A-00-0000-0D0PB40DT
90
C4 475 536 XHP35A-00-0000-0D0UC40DT
C2 440 497 XHP35A-00-0000-0D0UC20DT
B4 410 463 XHP35A-00-0000-0D0UB40DT
6500 K 1A, 1B, 1C, 1D
0 68
e4 635 717 XHP35A-00-0000-0D00e40e1
e2 590 666 XHP35A-00-0000-0D00e20e1
D4 550 621 XHP35A-00-0000-0D00D40e1
70
e4 635 717 XHP35A-00-0000-0D0Be40e1
e2 590 666 XHP35A-00-0000-0D0Be20e1
D4 550 621 XHP35A-00-0000-0D0BD40e1
80D4 550 621 XHP35A-00-0000-0D0HD40e1
D2 510 576 XHP35A-00-0000-0D0HD20e1
85
C4 475 536 XHP35A-00-0000-0D0PC40e1
C2 440 497 XHP35A-00-0000-0D0PC20e1
B4 410 463 XHP35A-00-0000-0D0PB40e1
90
C4 475 536 XHP35A-00-0000-0D0UC40e1
C2 440 497 XHP35A-00-0000-0D0UC20e1
B4 410 463 XHP35A-00-0000-0D0UB40e1
77
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
7
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
6000 K
1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U, 2A, 2B, 2C, 2D, 2R, 2S, 2T, 2U
0 68
e4 635 717 XHP35A-00-0000-0D00e40Dv
e2 590 666 XHP35A-00-0000-0D00e20Dv
D4 550 621 XHP35A-00-0000-0D00D40Dv
70
e4 635 717 XHP35A-00-0000-0D0Be40Dv
e2 590 666 XHP35A-00-0000-0D0Be20Dv
D4 550 621 XHP35A-00-0000-0D0BD40Dv
80D4 550 621 XHP35A-00-0000-0D0HD40Dv
D2 510 576 XHP35A-00-0000-0D0HD20Dv
85
C4 475 536 XHP35A-00-0000-0D0PC40Dv
C2 440 497 XHP35A-00-0000-0D0PC20Dv
B4 410 463 XHP35A-00-0000-0D0PB40Dv
90
C4 475 536 XHP35A-00-0000-0D0UC40Dv
C2 440 497 XHP35A-00-0000-0D0UC20Dv
B4 410 463 XHP35A-00-0000-0D0UB40Dv
5700 K 2A, 2B, 2C, 2D
0 68
e4 635 717 XHP35A-00-0000-0D00e40e2
e2 590 666 XHP35A-00-0000-0D00e20e2
D4 550 621 XHP35A-00-0000-0D00D40e2
70
e4 635 717 XHP35A-00-0000-0D0Be40e2
e2 590 666 XHP35A-00-0000-0D0Be20e2
D4 550 621 XHP35A-00-0000-0D0BD40e2
80D4 550 621 XHP35A-00-0000-0D0HD40e2
D2 510 576 XHP35A-00-0000-0D0HD20e2
85
C4 475 536 XHP35A-00-0000-0D0PC40e2
C2 440 497 XHP35A-00-0000-0D0PC20e2
B4 410 463 XHP35A-00-0000-0D0PB40e2
90
C4 475 536 XHP35A-00-0000-0D0UC40e2
C2 440 497 XHP35A-00-0000-0D0UC20e2
B4 410 463 XHP35A-00-0000-0D0UB40e2
FLuX CHArACtEristiCs, HigH DEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
88
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
8
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
5000 K 3A, 3B, 3C, 3D
0 68
e4 635 717 XHP35A-00-0000-0D00e40e3
e2 590 666 XHP35A-00-0000-0D00e20e3
D4 550 621 XHP35A-00-0000-0D00D40e3
70
e4 635 717 XHP35A-00-0000-0D0Be40e3
e2 590 666 XHP35A-00-0000-0D0Be20e3
D4 550 621 XHP35A-00-0000-0D0BD40e3
80D4 550 621 XHP35A-00-0000-0D0HD40e3
D2 510 576 XHP35A-00-0000-0D0HD20e3
85
C4 475 536 XHP35A-00-0000-0D0PC40e3
C2 440 497 XHP35A-00-0000-0D0PC20e3
B4 410 463 XHP35A-00-0000-0D0PB40e3
90
C4 475 536 XHP35A-00-0000-0D0UC40e3
C2 440 497 XHP35A-00-0000-0D0UC20e3
B4 410 463 XHP35A-00-0000-0D0UB40e3
4500 K 4A, 4B, 4C, 4D
0 68e2 590 666 XHP35A-00-0000-0D00e20e4
D4 550 621 XHP35A-00-0000-0D00D40e4
70e2 590 666 XHP35A-00-0000-0D0Be20e4
D4 550 621 XHP35A-00-0000-0D0BD40e4
80D4 550 621 XHP35A-00-0000-0D0HD40e4
D2 510 576 XHP35A-00-0000-0D0HD20e4
85
C4 475 536 XHP35A-00-0000-0D0PC40e4
C2 440 497 XHP35A-00-0000-0D0PC20e4
B4 410 463 XHP35A-00-0000-0D0PB40e4
90
C4 475 536 XHP35A-00-0000-0D0UC40e4
C2 440 497 XHP35A-00-0000-0D0UC20e4
B4 410 463 XHP35A-00-0000-0D0UB40e4
FLuX CHArACtEristiCs, HigH DEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
99
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
9
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
4000 K 5A, 5B, 5C, 5D
0 68
e2 590 666 XHP35A-00-0000-0D00e20e5
D4 550 621 XHP35A-00-0000-0D00D40e5
D2 510 576 XHP35A-00-0000-0D00D20e5
70
e2 590 666 XHP35A-00-0000-0D0Be20e5
D4 550 621 XHP35A-00-0000-0D0BD40e5
D2 510 576 XHP35A-00-0000-0D0BD20e5
80D4 550 621 XHP35A-00-0000-0D0HD40e5
D2 510 576 XHP35A-00-0000-0D0HD20e5
85C2 440 497 XHP35A-00-0000-0D0PC20e5
B4 410 463 XHP35A-00-0000-0D0PB40e5
90C2 440 497 XHP35A-00-0000-0D0UC20e5
B4 410 463 XHP35A-00-0000-0D0UB40e5
3500 K 6A, 6B, 6C, 6D
70
e2 590 666 XHP35A-00-0000-0D0Be20e6
D4 550 621 XHP35A-00-0000-0D0BD40e6
D2 510 576 XHP35A-00-0000-0D0BD20e6
80
D4 550 621 XHP35A-00-0000-0D0HD40e6
D2 510 576 XHP35A-00-0000-0D0HD20e6
C4 475 536 XHP35A-00-0000-0D0HC40e6
85C2 440 497 XHP35A-00-0000-0D0PC20e6
B4 410 463 XHP35A-00-0000-0D0PB40e6
90C2 440 497 XHP35A-00-0000-0D0UC20e6
B4 410 463 XHP35A-00-0000-0D0UB40e6
3000 K 7A, 7B, 7C, 7D
70D4 550 621 XHP35A-00-0000-0D0BD40e7
D2 510 576 XHP35A-00-0000-0D0BD20e7
80D2 510 576 XHP35A-00-0000-0D0HD20e7
C4 475 536 XHP35A-00-0000-0D0HC40e7
85
C2 440 497 XHP35A-00-0000-0D0PC20e7
B4 410 463 XHP35A-00-0000-0D0PB40e7
B2 380 429 XHP35A-00-0000-0D0PB20e7
90
C2 440 497 XHP35A-00-0000-0D0UC20e7
B4 410 463 XHP35A-00-0000-0D0UB40e7
B2 380 429 XHP35A-00-0000-0D0UB20e7
FLuX CHArACtEristiCs, HigH DEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1010
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
10
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
2700 K 8A, 8B, 8C, 8D
80C4 475 536 XHP35A-00-0000-0D0HC40e8
C2 440 497 XHP35A-00-0000-0D0HC20e8
85B4 410 463 XHP35A-00-0000-0D0PB40e8
B2 380 429 XHP35A-00-0000-0D0PB20e8
90B4 410 463 XHP35A-00-0000-0D0UB40e8
B2 380 429 XHP35A-00-0000-0D0UB20e8
FLuX CHArACtEristiCs, HigH intEnsity EAsyWHitE® orDEr CoDEs AnD bins (tJ = 85 °C)
The following table provides order codes for XLamp XHP35 High Intensity LEDs. For a complete description of how the flux and chromaticity
groups are reflected in the bin code and order code nomenclature, please see the Bin and Order Code Formats section (page 31).
nominalCCt
Cri Minimum Luminous Flux @350 mA 3-step 5-step
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* group order Code group order Code
5700 K
70D2 510 576
57eXHP35A-H0-0000-0D0BD257e
C4 475 536 XHP35A-H0-0000-0D0BC457e
80C4 475 536
57eXHP35A-H0-0000-0D0HC457e
C2 440 497 XHP35A-H0-0000-0D0HC257e
85
B4 410 463
57e
XHP35A-H0-0000-0D0PB457e
B2 380 429 XHP35A-H0-0000-0D0PB257e
A4 355 395 XHP35A-H0-0000-0D0PA457e
90
B4 410 463
57e
XHP35A-H0-0000-0D0UB457e
B2 380 429 XHP35A-H0-0000-0D0UB257e
A4 355 395 XHP35A-H0-0000-0D0UA457e
FLuX CHArACtEristiCs, HigH DEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1111
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
11
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nominalCCt
Cri Minimum Luminous Flux @350 mA 3-step 5-step
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* group order Code group order Code
5000 K
70D2 510 576
50eXHP35A-H0-0000-0D0BD250e
C4 475 536 XHP35A-H0-0000-0D0BC450e
80C4 475 536
50eXHP35A-H0-0000-0D0HC450e
C2 440 497 XHP35A-H0-0000-0D0HC250e
85
B4 410 463
50e
XHP35A-H0-0000-0D0PB450e
B2 380 429 XHP35A-H0-0000-0D0PB250e
A4 355 395 XHP35A-H0-0000-0D0PA450e
90
B4 410 463
50e
XHP35A-H0-0000-0D0UB450e
B2 380 429 XHP35A-H0-0000-0D0UB250e
A4 355 395 XHP35A-H0-0000-0D0UA450e
4500 K
70D2 510 576
45eXHP35A-H0-0000-0D0BD245e
C4 475 536 XHP35A-H0-0000-0D0BC445e
80C4 475 536
45eXHP35A-H0-0000-0D0HC445e
C2 440 497 XHP35A-H0-0000-0D0HC245e
85B2 380 429
45eXHP35A-H0-0000-0D0PB245e
A4 355 395 XHP35A-H0-0000-0D0PA445e
90B2 380 429
45eXHP35A-H0-0000-0D0UB245e
A4 355 395 XHP35A-H0-0000-0D0UA445e
4000 K
70
D2 510 576
40e
XHP35A-H0-0000-0D0BD240e
C4 475 536 XHP35A-H0-0000-0D0BC440e
C2 440 497 XHP35A-H0-0000-0D0BC240e
80C4 475 536
40eXHP35A-H0-0000-0D0HC440e
C2 440 497 XHP35A-H0-0000-0D0HC240e
85B2 380 429
40eXHP35A-H0-0000-0D0PB240e
A4 355 395 XHP35A-H0-0000-0D0PA440e
90B2 380 429
40eXHP35A-H0-0000-0D0UB240e
A4 355 395 XHP35A-H0-0000-0D0UA440e
FLuX CHArACtEristiCs, HigH intEnsity EAsyWHitE® orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1212
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
12
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nominalCCt
Cri Minimum Luminous Flux @350 mA 3-step 5-step
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C* group order Code group order Code
3500 K
70
D2 510 576
35e
XHP35A-H0-0000-0D0BD235e
C4 475 536 XHP35A-H0-0000-0D0BC435e
C2 440 497 XHP35A-H0-0000-0D0BC235e
80
C4 475 536
35G
XHP35A-H0-0000-0D0HC435G
35e
XHP35A-H0-0000-0D0HC435e
C2 440 497 XHP35A-H0-0000-0D0HC235G XHP35A-H0-0000-0D0HC235e
B4 410 463 XHP35A-H0-0000-0D0HB435G XHP35A-H0-0000-0D0HB435e
85B2 380 429
35GXHP35A-H0-0000-0D0PB235G
35eXHP35A-H0-0000-0D0PB235e
A4 355 395 XHP35A-H0-0000-0D0PA435G XHP35A-H0-0000-0D0PA435e
90B2 380 429
35GXHP35A-H0-0000-0D0UB235G
35eXHP35A-H0-0000-0D0UB235e
A4 355 395 XHP35A-H0-0000-0D0UA435G XHP35A-H0-0000-0D0UA435e
3000 K
70
D2 510 576
30e
XHP35A-H0-0000-0D0BD230e
C4 475 536 XHP35A-H0-0000-0D0BC430e
C2 440 497 XHP35A-H0-0000-0D0BC230e
80C2 440 497
30GXHP35A-H0-0000-0D0HC230G
30eXHP35A-H0-0000-0D0HC230e
B4 410 463 XHP35A-H0-0000-0D0HB430G XHP35A-H0-0000-0D0HB430e
85
B2 380 429
30G
XHP35A-H0-0000-0D0PB230G
30e
XHP35A-H0-0000-0D0PB230e
A4 355 395 XHP35A-H0-0000-0D0PA430G XHP35A-H0-0000-0D0PA430e
A2 330 367 XHP35A-H0-0000-0D0PA230G XHP35A-H0-0000-0D0PA230e
90
B2 380 429
30G
XHP35A-H0-0000-0D0UB230G
30e
XHP35A-H0-0000-0D0UB230e
A4 355 395 XHP35A-H0-0000-0D0UA430G XHP35A-H0-0000-0D0UA430e
A2 330 367 XHP35A-H0-0000-0D0UA230G XHP35A-H0-0000-0D0UA230e
2700 K
80
C2 440 497
27G
XHP35A-H0-0000-0D0HC227G
27e
XHP35A-H0-0000-0D0HC227e
B4 410 463 XHP35A-H0-0000-0D0HB427G XHP35A-H0-0000-0D0HB427e
B2 380 429 XHP35A-H0-0000-0D0HB227G XHP35A-H0-0000-0D0HB227e
85
B2 380 429
27G
XHP35A-H0-0000-0D0PB227G
27e
XHP35A-H0-0000-0D0PB227e
A4 355 395 XHP35A-H0-0000-0D0PA427G XHP35A-H0-0000-0D0PA427e
A2 330 367 XHP35A-H0-0000-0D0PA227G XHP35A-H0-0000-0D0PA227e
90
B2 380 429
27G
XHP35A-H0-0000-0D0UB227G
27e
XHP35A-H0-0000-0D0UB227e
A4 355 395 XHP35A-H0-0000-0D0UA427G XHP35A-H0-0000-0D0UA427e
A2 330 367 XHP35A-H0-0000-0D0UA227G XHP35A-H0-0000-0D0UA227e
FLuX CHArACtEristiCs, HigH intEnsity EAsyWHitE® orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1313
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
13
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
FLuX CHArACtEristiCs, HigH intEnsity Ansi WHitE orDEr CoDEs AnD bins (tJ = 85 °C)
The following table provides order codes for XLamp XHP35 LEDs. For a complete description of how the flux and chromaticity groups are
reflected in the bin code and order code nomenclature, please see the Bin and Order Code Formats section (page 31).
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
7000 K
0A, 0B, 0C, 0D, 0R, 0S, 0T, 0U, 1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U
0 68D2 510 576 XHP35A-H0-0000-0D00D20DT
C4 475 536 XHP35A-H0-0000-0D00C40DT
70D2 510 576 XHP35A-H0-0000-0D0BD20DT
C4 475 536 XHP35A-H0-0000-0D0BC40DT
80C4 475 536 XHP35A-H0-0000-0D0HC40DT
C2 440 497 XHP35A-H0-0000-0D0HC20DT
85
B4 410 463 XHP35A-H0-0000-0D0PB40DT
B2 380 429 XHP35A-H0-0000-0D0PB20DT
A4 355 395 XHP35A-H0-0000-0D0PA40DT
90
B4 410 463 XHP35A-H0-0000-0D0UB40DT
B2 380 429 XHP35A-H0-0000-0D0UB20DT
A4 355 395 XHP35A-H0-0000-0D0UA40DT
6500 K 1A, 1B, 1C, 1D
0 68D2 510 576 XHP35A-H0-0000-0D00D20e1
C4 475 536 XHP35A-H0-0000-0D00C40e1
70D2 510 576 XHP35A-H0-0000-0D0BD20e1
C4 475 536 XHP35A-H0-0000-0D0BC40e1
80C4 475 536 XHP35A-H0-0000-0D0HC40e1
C2 440 497 XHP35A-H0-0000-0D0HC20e1
85
B4 410 463 XHP35A-H0-0000-0D0PB40e1
B2 380 429 XHP35A-H0-0000-0D0PB20e1
A4 355 395 XHP35A-H0-0000-0D0PA40e1
90
B4 410 463 XHP35A-H0-0000-0D0UB40e1
B2 380 429 XHP35A-H0-0000-0D0UB20e1
A4 355 395 XHP35A-H0-0000-0D0UA40e1
1414
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
14
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
6000 K
1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U, 2A, 2B, 2C, 2D, 2R, 2S, 2T, 2U
0 68D2 510 576 XHP35A-H0-0000-0D00D20Dv
C4 475 536 XHP35A-H0-0000-0D00C40Dv
70D2 510 576 XHP35A-H0-0000-0D0BD20Dv
C4 475 536 XHP35A-H0-0000-0D0BC40Dv
80C4 475 536 XHP35A-H0-0000-0D0HC40Dv
C2 440 497 XHP35A-H0-0000-0D0HC20Dv
85
B4 410 463 XHP35A-H0-0000-0D0PB40Dv
B2 380 429 XHP35A-H0-0000-0D0PB20Dv
A4 355 395 XHP35A-H0-0000-0D0PA40Dv
90
B4 410 463 XHP35A-H0-0000-0D0UB40Dv
B2 380 429 XHP35A-H0-0000-0D0UB20Dv
A4 355 395 XHP35A-H0-0000-0D0UA40Dv
5700 K 2A, 2B, 2C, 2D
0 68D2 510 576 XHP35A-H0-0000-0D00D20e2
C4 475 536 XHP35A-H0-0000-0D00C40e2
70D2 510 576 XHP35A-H0-0000-0D0BD20e2
C4 475 536 XHP35A-H0-0000-0D0BC40e2
80C4 475 536 XHP35A-H0-0000-0D0HC40e2
C2 440 497 XHP35A-H0-0000-0D0HC20e2
85
B4 410 463 XHP35A-H0-0000-0D0PB40e2
B2 380 429 XHP35A-H0-0000-0D0PB20e2
A4 355 395 XHP35A-H0-0000-0D0PA40e2
90
B4 410 463 XHP35A-H0-0000-0D0UB40e2
B2 380 429 XHP35A-H0-0000-0D0UB20e2
A4 355 395 XHP35A-H0-0000-0D0UA40e2
5000 K 3A, 3B, 3C, 3D
0 68D2 510 576 XHP35A-H0-0000-0D00D20e3
C4 475 536 XHP35A-H0-0000-0D00C40e3
70D2 510 576 XHP35A-H0-0000-0D0BD20e3
C4 475 536 XHP35A-H0-0000-0D0BC40e3
80C4 475 536 XHP35A-H0-0000-0D0HC40e3
C2 440 497 XHP35A-H0-0000-0D0HC20e3
85
B4 410 463 XHP35A-H0-0000-0D0PB40e3
B2 380 429 XHP35A-H0-0000-0D0PB20e3
A4 355 395 XHP35A-H0-0000-0D0PA40e3
90
B4 410 463 XHP35A-H0-0000-0D0UB40e3
B2 380 429 XHP35A-H0-0000-0D0UB20e3
A4 355 395 XHP35A-H0-0000-0D0UA40e3
FLuX CHArACtEristiCs, HigH intEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1515
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
15
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
4500 K 4A, 4B, 4C, 4D
0 68D2 510 576 XHP35A-H0-0000-0D00D20e4
C4 475 536 XHP35A-H0-0000-0D00C40e4
70D2 510 576 XHP35A-H0-0000-0D0BD20e4
C4 475 536 XHP35A-H0-0000-0D0BC40e4
80C4 475 536 XHP35A-H0-0000-0D0HC40e4
C2 440 497 XHP35A-H0-0000-0D0HC20e4
85
B4 410 463 XHP35A-H0-0000-0D0PB40e4
B2 380 429 XHP35A-H0-0000-0D0PB20e4
A4 355 395 XHP35A-H0-0000-0D0PA40e4
90
B4 410 463 XHP35A-H0-0000-0D0UB40e4
B2 380 429 XHP35A-H0-0000-0D0UB20e4
A4 355 395 XHP35A-H0-0000-0D0UA40e4
4000 K 5A, 5B, 5C, 5D
0 68
D2 510 576 XHP35A-H0-0000-0D00D20e5
C4 475 536 XHP35A-H0-0000-0D00C40e5
C2 440 497 XHP35A-H0-0000-0D00C20e5
70
D2 510 576 XHP35A-H0-0000-0D0BD20e5
C4 475 536 XHP35A-H0-0000-0D0BC40e5
C2 440 497 XHP35A-H0-0000-0D0BC20e5
80C4 475 536 XHP35A-H0-0000-0D0HC40e5
C2 440 497 XHP35A-H0-0000-0D0HC20e5
85B2 380 429 XHP35A-H0-0000-0D0PB20e5
A4 355 395 XHP35A-H0-0000-0D0PA40e5
90B2 380 429 XHP35A-H0-0000-0D0UB20e5
A4 355 395 XHP35A-H0-0000-0D0UA40e5
3500 K 6A, 6B, 6C, 6D
70
D2 510 576 XHP35A-H0-0000-0D0BD20e6
C4 475 536 XHP35A-H0-0000-0D0BC40e6
C2 440 497 XHP35A-H0-0000-0D0BC20e6
80
C4 475 536 XHP35A-H0-0000-0D0HC40e6
C2 440 497 XHP35A-H0-0000-0D0HC20e6
B4 410 463 XHP35A-H0-0000-0D0HB40e6
85B2 380 429 XHP35A-H0-0000-0D0PB20e6
A4 355 395 XHP35A-H0-0000-0D0PA40e6
90B2 380 429 XHP35A-H0-0000-0D0UB20e6
A4 355 395 XHP35A-H0-0000-0D0UA40e6
FLuX CHArACtEristiCs, HigH intEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1616
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
16
XLamp® XHp35 LED
Notes:• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements.
See the Measurements section (page 33).• Cree XLamp XHP35 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum
specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code.* Flux values @ 25 °C are calculated and are for reference only.
nomimalCCt Chromaticity regions
Cri Minimum Luminous Flux @ 350 mA
order Code
Min typ group Flux (lm) @ 85 °C
Flux (lm) @ 25 °C*
3000 K 7A, 7B, 7C, 7D
70
D2 510 576 XHP35A-H0-0000-0D0BD20e7
C4 475 536 XHP35A-H0-0000-0D0BC40e7
C2 440 497 XHP35A-H0-0000-0D0BC20e7
80C2 420 497 XHP35A-H0-0000-0D0HC20e7
B4 410 463 XHP35A-H0-0000-0D0HB40e7
85
B2 380 429 XHP35A-H0-0000-0D0PB20e7
A4 355 395 XHP35A-H0-0000-0D0PA40e7
A2 330 367 XHP35A-H0-0000-0D0PA20e7
90
B2 380 429 XHP35A-H0-0000-0D0UB20e7
A4 355 395 XHP35A-H0-0000-0D0UA40e7
A2 330 367 XHP35A-H0-0000-0D0UA20e7
2700 K 8A, 8B, 8C, 8D
80
C2 420 497 XHP35A-H0-0000-0D0HC20e8
B4 410 463 XHP35A-H0-0000-0D0HB40e8
B2 380 429 XHP35A-H0-0000-0D0HB20e8
85
B2 380 429 XHP35A-H0-0000-0D0PB20e8
A4 355 395 XHP35A-H0-0000-0D0PA40e8
A2 330 367 XHP35A-H0-0000-0D0PA20e8
90
B2 380 429 XHP35A-H0-0000-0D0UB20e8
A4 355 395 XHP35A-H0-0000-0D0UA40e8
A2 330 367 XHP35A-H0-0000-0D0UA20e8
FLuX CHArACtEristiCs, HigH intEnsity Ansi orDEr CoDEs AnD bins (tJ = 85 °C) - Continued
1717
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
17
XLamp® XHp35 LED
rELAtivE sPECtrAL PoWEr Distribution
rELAtivE FLuX vs. JunCtion tEMPErAturE (iF = 350 mA)
Relative Spectral Power
0%
20%
40%
60%
80%
100%
380 430 480 530 580 630 680 730 780
Rela
tive
Radi
ant P
ower
Wavelength (nm)
6000 K, 70 CRI
5000 K, 70 CRI
3000 K, 80 CRI
Relative Flux Output vs. Junction Temperature
0%
20%
40%
60%
80%
100%
120%
25 50 75 100 125 150
Rela
tive
Lum
inou
s Fl
ux
Junction Temperature (ºC)
1818
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
18
XLamp® XHp35 LED
ELECtriCAL CHArACtEristiCs (tJ = 85 °C)
rELAtivE FLuX vs. CurrEnt (tJ = 85 °C)
Electrical Characteristics (Tj = 85°C)
175
350
525
700
875
1050
10.5 11.0 11.5 12.0 12.5
Forw
ard
Curr
ent (
mA
)
Forward Voltage (V)
Relative Intensity vs. Current (Tj = 85°C)
0%
40%
80%
120%
160%
200%
240%
0 175 350 525 700 875 1050
Rela
tive
Lum
inou
s Fl
ux
Forward Current (mA)
1919
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
19
XLamp® XHp35 LED
RelAtive ChRomAtiCity vs. CuRRent (WARm White)Relative Chromaticity Vs. Current, WW - High Density
-0.020
-0.016
-0.012
-0.008
-0.004
0.000
0.004
0.008
0.012
0.016
0.020
0 175 350 525 700 875 1050
Current (mA)
ΔCCx
ΔCCy
High Density
Relative Chromaticity Vs. Current, WW - High Intensity
-0.020
-0.016
-0.012
-0.008
-0.004
0.000
0.004
0.008
0.012
0.016
0.020
0 175 350 525 700 875 1050
Current (mA)
ΔCCx
ΔCCy
High Intensity
2020
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
20
XLamp® XHp35 LED
RelAtive ChRomAtiCity vs. tempeRAtuRe (WARm White)Relative Chromaticity Vs. Temperature WW - High Density
-0.020
-0.016
-0.012
-0.008
-0.004
0.000
0.004
0.008
0.012
0.016
0.020
25 50 75 100 125 150
Tsp (°C)
ΔCCx
ΔCCy
High Density
Relative Chromaticity Vs. Temperature WW - High Intensity
-0.020
-0.016
-0.012
-0.008
-0.004
0.000
0.004
0.008
0.012
0.016
0.020
25 50 75 100 125 150
Tsp (°C)
ΔCCx
ΔCCy
High Intensity
2121
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
21
XLamp® XHp35 LED
tyPiCAL sPAtiAL Distribution
0%
20%
40%
60%
80%
100%
-90 -70 -50 -30 -10 10 30 50 70 90
Rela
tive
Lum
inou
s In
tens
ity
Angle (º)
High Density
Typical Spatial Radiation Pattern
0%
20%
40%
60%
80%
100%
-90 -70 -50 -30 -10 10 30 50 70 90
Rela
tive
Lum
inou
s In
tens
ity
Angle (º)
High Intensity
2222
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
22
XLamp® XHp35 LED
tHErMAL DEsign
The maximum forward current is determined by the thermal resistance between the LeD junction and ambient. It is crucial for the end
product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life
and optical characteristics.
PErForMAnCE grouPs – LuMinous FLuX (tJ = 85 °C)
XLamp XHP35 LEDs are tested for luminous flux and placed into one of the following luminous-flux groups.
group Code Minimum Luminous Flux Maximum Luminous Flux
A2 330 355
A4 355 380
B2 380 410
B4 410 440
C2 440 475
C4 475 510
D2 510 550
D4 550 590
e2 590 635
e4 635 680
F2 680 730
Thermal Design - High Intensity
0
200
400
600
800
1000
1200
0 20 40 60 80 100 120 140 160
Max
imum
Cur
rent
(mA
)
Ambient Temperature (ºC)
Rj-a = 2°C/W
Rj-a = 4°C/W
Rj-a = 6°C/W
Rj-a = 8°C/W
XHP35 High Intensity
2323
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
23
XLamp® XHp35 LED
PErForMAnCE grouPs – CHroMAtiCity
XLamp XHP35 LEDs are tested for chromaticity and placed into one of the regions defined by the following bounding coordinates.
EasyWhite Color temperatures – 3-step Ellipse
bin Code CCtCenter Point Major Axis Minor Axis rotation Angle
(°)x y a b
35G 3500 K 0.4073 0.3917 0.00927 0.00414 54.0
30G 3000 K 0.4338 0.4030 0.00834 0.00408 53.2
27G 2700 K 0.4577 0.4099 0.00834 0.00420 48.5
EasyWhite Color temperatures – 5-step Ellipse
bin Code CCtCenter Point Major Axis Minor Axis rotation Angle
(°)x y a b
57e 5700 K 0.3287 0.3417 0.01230 0.00600 72.0
50e 5000 K 0.3447 0.3553 0.01400 0.00520 65.0
45e 4500 K 0.3611 0.3658 0.01420 0.00550 61.5
40e 4000 K 0.3818 0.3797 0.01565 0.00670 53.7
35e 3500 K 0.4073 0.3917 0.01545 0.00690 54.0
30e 3000 K 0.4338 0.4030 0.01390 0.00680 53.2
27e 2700 K 0.4577 0.4099 0.01350 0.00700 48.5
Ansi White bins Ansi White bins
CCt bin Code x y CCt bin Code x y
7000 K
0A0
0.2950 0.2970
7000 K
0R0
0.2980 0.2880
0.2920 0.3060 0.2950 0.2970
0.2984 0.3133 0.3009 0.3042
0.3009 0.3042 0.3037 0.2937
0B0
0.2920 0.3060
0S0
0.2895 0.3135
0.2895 0.3135 0.2870 0.3210
0.2962 0.3220 0.2937 0.3312
0.2984 0.3133 0.2962 0.3220
0C0
0.2984 0.3133
0T0
0.2962 0.3220
0.2962 0.3220 0.2937 0.3312
0.3028 0.3304 0.3005 0.3415
0.3048 0.3207 0.3028 0.3304
0D0
0.2984 0.3133
0U0
0.3037 0.2937
0.3048 0.3207 0.3009 0.3042
0.3068 0.3113 0.3068 0.3113
0.3009 0.3042 0.3093 0.2993
2424
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
24
XLamp® XHp35 LED
Ansi White bins Ansi White bins
CCt bin Code x y CCt bin Code x y
6500 K
1A0
0.3048 0.3207
6500 K
1R0
0.3068 0.3113
0.3130 0.3290 0.3144 0.3186
0.3144 0.3186 0.3161 0.3059
0.3068 0.3113 0.3093 0.2993
1B0
0.3028 0.3304
1S0
0.3005 0.3415
0.3115 0.3391 0.3099 0.3509
0.3130 0.3290 0.3115 0.3391
0.3048 0.3207 0.3028 0.3304
1C0
0.3115 0.3391
1T0
0.3099 0.3509
0.3205 0.3481 0.3196 0.3602
0.3213 0.3373 0.3205 0.3481
0.3130 0.3290 0.3115 0.3391
1D0
0.3130 0.3290
1U0
0.3144 0.3186
0.3213 0.3373 0.3221 0.3261
0.3221 0.3261 0.3231 0.3120
0.3144 0.3186 0.3161 0.3059
Ansi White bins Ansi White bins
CCt bin Code x y CCt bin Code x y
5700 K
2A0
0.3215 0.3350
5700 K
2R0
0.3222 0.3243
0.3290 0.3417 0.3290 0.3300
0.3290 0.3300 0.3290 0.3180
0.3222 0.3243 0.3231 0.3120
2B0
0.3207 0.3462
2S0
0.3196 0.3602
0.3290 0.3538 0.3290 0.3690
0.3290 0.3417 0.3290 0.3538
0.3215 0.3350 0.3207 0.3462
2C0
0.3290 0.3538
2T0
0.3290 0.3690
0.3376 0.3616 0.3381 0.3762
0.3371 0.3490 0.3376 0.3616
0.3290 0.3417 0.3290 0.3538
2D0
0.3290 0.3417
2U0
0.3290 0.3300
0.3371 0.3490 0.3366 0.3369
0.3366 0.3369 0.3361 0.3245
0.3290 0.3300 0.3290 0.3180
peRFoRmAnCe GRoups – ChRomAtiCity (Continued)
2525
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
25
XLamp® XHp35 LED
Ansi White bins Ansi White bins
CCt bin Code x y CCt bin Code x y
5000 K
3A0
.3371 .3490
4500 K
4A0
0.3530 0.3597
.3451 .3554 0.3615 0.3659
.3440 .3427 0.3512 0.3465
.3366 .3369 0.3515 0.3487
3B0
.3376 .3616
4B0
0.3548 0.3736
.3463 .3687 0.3641 0.3804
.3451 .3554 0.3530 0.3597
.3371 .3490 0.3533 0.362
3C0
.3463 .3687
4C0
0.3641 0.3804
.3551 .3760 0.3736 0.3874
.3533 .3620 0.3702 0.3722
.3451 .3554 0.3615 0.3659
3D0
.3451 .3554
4D0
0.3615 0.3659
.3533 .3620 0.3702 0.3722
.3515 .3487 0.3670 0.3578
.3440 .3427 0.3590 0.3521
Ansi White bins Ansi White bins
CCt bin Code x y CCt bin Code x y
4000 K
5A0
.3670 .3578
3500 K
6A0
.3889 .3690
.3702 .3722 .3941 .3848
.3825 .3798 .4080 .3916
.3783 .3646 .4017 .3751
5B0
.3702 .3722
6B0
.3941 .3848
.3736 .3874 .3996 .4015
.3869 .3958 .4146 .4089
.3825 .3798 .4080 .3916
5C0
.3825 .3798
6C0
.4080 .3916
.3869 .3958 .4146 .4089
.4006 .4044 .4299 .4165
.3950 .3875 .4221 .3984
5D0
.3783 .3646
6D0
.4017 .3751
.3825 .3798 .4080 .3916
.3950 .3875 .4221 .3984
.3898 .3716 .4147 .3814
peRFoRmAnCe GRoups – ChRomAtiCity (Continued)
2626
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
26
XLamp® XHp35 LED
Ansi White bins Ansi White bins
CCt bin Code x y CCt bin Code x y
3000 K
7A0
.4147 .3814
2700 K
8A0
.4373 .3893
.4221 .3984 .4465 .4071
.4342 .4028 .4582 .4099
.4259 .3853 .4483 .3919
7B0
.4221 .3984
8B0
.4465 .4071
.4299 .4165 .4562 .4260
.4430 .4212 .4687 .4289
.4342 .4028 .4582 .4099
7C0
.4342 .4028
8C0
.4582 .4099
.4430 .4212 .4687 .4289
.4562 .4260 .4813 .4319
.4465 .4071 .4700 .4126
7D0
.4259 .3853
8D0
.4483 .3919
.4342 .4028 .4582 .4099
.4465 .4071 .4700 .4126
.4373 .3893 .4593 .3944
CrEE’s EAsyWHitE® CHroMAtiCity rEgions PLottED on tHE 1931 CiE CurvE
ANSI Cool White
5000 K
5700 K
6500 K
8000 K
0A
0B
0C
0D
0R
0S
0T
0U
1A
1B
1C
1D2A
2B
2C
2D
1R
1S
1T
1U
2R
2S
2T
2U
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
CC
y
CCx
ANSIC78.377A
peRFoRmAnCe GRoups – ChRomAtiCity (Continued)
2727
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
27
XLamp® XHp35 LED
CrEE’s EAsyWHitE® CHroMAtiCity rEgions PLottED on tHE 1931 CiE CurvE - ContinuED
ANSI Neutral White and ANSI Warm White
2700 K 3000 K
3500 K
4000 K
4500 K
5000 K
5700 K
3A
3B
3C
3D 4A
4B
4C
4D
5A
5B
5C
5D 6A
6B
6C
6D 7A
7B 7C
7D 8A
8B 8C
8D
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.46
0.47
0.48
0.49
CCy
CCx
2828
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
28
XLamp® XHp35 LED
CrEE’s EAsyWHitE® CHroMAtiCity rEgions PLottED on tHE 1931 CiE CurvE - ContinuED
2700 K 3000 K
3500 K
4000 K
4500 K
5000 K
5700 K
6500 K
8000 K
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.27
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.46
0.47
0.48
0.49
CCy
CCx
ANSI C78.377 Quadrangle
EasyWhite 5-Step
EasyWhite 3-Step
2929
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
29
XLamp® XHp35 LED
CrEE’s stAnDArD CooL WHitE Kits PLottED on Ansi stAnDArD CHroMAtiCity rEgions
5000 K
5700 K
6500 K
8000 K
0A
0B
0C
0D
0R
0S
0T
0U
1A
1B
1C
1D
2A
2B
2C
2D
1R
1S
1T
1U
2R
2S
2T
2U
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
CCy
CCx
ANSIC78.377A
DT
5000 K
5700 K
6500 K
8000 K
0A
0B
0C
0D
0R
0S
0T
0U
1A
1B
1C
1D
2A
2B
2C
2D
1R
1S
1T
1U
2R
2S
2T
2U
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
CCy
CCx
ANSIC78.377A
DV
5000 K
5700 K
6500 K
8000 K
0A
0B
0C
0D
0R
0S
0T
0U
1A
1B
1C
1D
2A
2B
2C
2D
3A
3B
1R
1S
1T
1U
2R
2S
2T
2U
3R
3S
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
CCy
CCx
ANSIC78.377A
E1
5000 K
5700 K
6500 K
8000 K
0A
0B
0C
0D
0R
0S
0T
0U
1A
1B
1C
1D
2A
2B
2C
2D
3A
3B
1R
1S
1T
1U
2R
2S
2T
2U
3R
3S
0.28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.400.
28
0.29
0.30
0.31
0.32
0.33
0.34
0.35
0.36
CCy
CCx
ANSIC78.377A
E2
3030
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
30
XLamp® XHp35 LED
CrEE’s stAnDArD WArM AnD nEutrAL WHitE Kits PLottED on Ansi stAnDArD CHroMAtiCity rEgions
2700 K
3000 K
3500 K
4000 K
4500 K5000 K
3A
3B
3C
3D4A
4B
4C
4D
5A
5B
5C
5D6A
6B
6C
6D
7A
7B7C
7D
8B
8A8D
8C
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.42
0.43
0.44
0.45
0.46
0.47
0.48
0.49
0.50
CCy
CCx
E3
E4
E5
E6
E7E8
ANSIC78.377A
3131
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
31
XLamp® XHp35 LED
bin AnD orDEr CoDE ForMAts
Bin codes and order codes for XHP35 LEDs are configured in the following manner:
bin Codeorder Code
SSSSSS-B-NNN-MMM-JK-L-PP
Series XHP35A = XHP35
Chromaticity group
Luminous flux group
Voltage performance group
CRI specification 0 = No minimum CRI B = 70 CRI minimum H = 80 CRI minimum P = 85 CRI minimum U = 90 CRI minimum
Internal code
Version 0 = High density H = High intensity
SSSSSS-BD-GGGG-HJKLMMNNN
Series XHP35A = XHP35
Internal code
Minimum luminous flux group
Chromaticity group
CRI specification 0 = No minimum CRI B = 70 CRI minimum H = 80 CRI minimum P = 85 CRI minimum U = 90 CRI minimum
Configuration B: Version 0 = High density H = High intensity D: Reel size
3232
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
32
XLamp® XHp35 LED
rEFLoW soLDEring CHArACtEristiCs
In testing, Cree has found XLamp XHP35 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general
guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used.
Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
Profile Feature Lead-Free solder
Average Ramp-Up Rate (Tsmax to Tp) 1.2 °C/second
Preheat: Temperature Min (Tsmin) 120 °C
Preheat: Temperature Max (Tsmax) 170 °C
Preheat: Time (tsmin to tsmax) 65-150 seconds
Time Maintained Above: Temperature (TL) 217 °C
Time Maintained Above: Time (tL) 45-90 seconds
Peak/Classification Temperature (Tp) 235 - 245 °C
Time Within 5 °C of Actual Peak Temperature (tp) 20-40 seconds
Ramp-Down Rate 1 - 6 °C/second
Time 25 °C to Peak Temperature 4 minutes max.
Note: All temperatures refer to the topside of the package, measured on the package body surface.
IPC/JEDEC J-STD-020C
TP
TL
Tem
pera
ture
Timet 25˚C to Peak
Preheatts
tS
tP
25
Ramp-down
Ramp-up
Critical ZoneTL to TP
Tsmax
Tsmin
3333
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
33
XLamp® XHp35 LED
notEs
MeasurementsThe luminous flux, radiant power, chromaticity and CRI measurements in this document are binning specifications only and solely
represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors
that are not within Cree’s control and are not intended or provided as operational specifications for the products. Calculated values are
provided for informational purposes only and are not intended as specifications.
pre-Release Qualification testingPlease read the LeD Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp
LEDs and details of Cree’s pre-release qualification testing for XLamp LEDs.
Lumen MaintenanceCree now uses standardized IeS LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LeD lumen maintenance.
For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document.
Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting.
Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect
the LeD junction temperature.
Moisture sensitivityCree recommends keeping XLamp LeDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering.
Unopened MBPs that contain XLamp LeDs do not need special storage for moisture sensitivity.
Once the MBP is opened, XLamp XHP35 LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in
conditions of ≤ 30 ºC/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs
in the original MBP.
roHs ComplianceThe levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold
limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as
implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product
Documentation sections of www.cree.com.
uL® recognized ComponentLevel 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/
UL 8750.
vision AdvisoryWARNING: Do not look at exposed lamp in operation. eye injury can result. For more information about LeDs and eye safety, please refer
to the LeD eye Safety application note.
3434
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
34
XLamp® XHp35 LED
MECHAniCAL DiMEnsions
Thermal vias, if present, are not shown on these drawings.
All dimensions are ±.13 mm unless otherwise indicated.
XHP35 High DensityXHP35A-0x-xxxx-xxxxxxxxx
XHP35 High Density
XHP35 High intensityXHP35A-Hx-xxxx-xxxxxxxxx
XHP35 High Intensity
bottom viewtop view
Anode
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
.65
3.30
.50
3.30
2.30
1.30
.50
3.45
3.45
R1.85
2.80
3.30
.50
2.30
.64
.75
.25
3.30
1.01
.50
.50
3.30
1.30
3.30
1/122.000
C2610-00053
OUTLINE DRAWING XHP35
5/11/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
.65
3.30
.50
3.30
2.30
1.30
.50
3.45
3.45
R1.85
2.80
3.30
.50
2.30
.64
.75
.25
3.30
1.01
.50
.50
3.30
1.30
3.30
1/122.000
C2610-00053
OUTLINE DRAWING XHP35
5/11/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
.65
3.30
.50
3.30
2.30
1.30
.50
3.45
3.45
R1.85
2.80
3.30
.50
2.30
.64
.75
.25
3.30
1.01
.50
.50
3.30
1.30
3.30
1/122.000
C2610-00053
OUTLINE DRAWING XHP35
5/11/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
side view
top view side view bottom view
Anode
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
3.30
.50
3.45
3.45
1.0
2.30
3.30
1.30
.50
3.30
2.30
.50
1.01
3.30
.75
.25
.64
3.30
1.30
3.30
.50.50
1/122.000
C2610-00057
OUTLINE DRAWING XHP35
3/13/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PADRECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
3.30
.50
3.45
3.45
1.0
2.30
3.30
1.30
.50
3.30
2.30
.50
1.01
3.30
.75
.25
.64
3.30
1.30
3.30
.50.50
1/122.000
C2610-00057
OUTLINE DRAWING XHP35
3/13/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PADRECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
3.30
.50
3.45
3.45
1.0
2.30
3.30
1.30
.50
3.30
2.30
.50
1.01
3.30
.75
.25
.64
3.30
1.30
3.30
.50.50
1/122.000
C2610-00057
OUTLINE DRAWING XHP35
3/13/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PADRECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
3535
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
35
XLamp® XHp35 LED
MECHAniCAL DiMEnsions - ContinuED
XHP35 High Density and XHP35 High intensity
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
.65
3.30
.50
3.30
2.30
1.30
.50
3.45
3.45
R1.85
2.80
3.30
.50
2.30
.64
.75
.25
3.30
1.01
.50
.50
3.30
1.30
3.30
1/122.000
C2610-00053
OUTLINE DRAWING XHP35
5/11/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6
.65
3.30
.50
3.30
2.30
1.30
.50
3.45
3.45
R1.85
2.80
3.30
.50
2.30
.64
.75
.25
3.30
1.01
.50
.50
3.30
1.30
3.30
1/122.000
C2610-00053
OUTLINE DRAWING XHP35
5/11/15D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PCB SOLDER PAD
RECOMMENDED STENCIL PATTERN(HATCHED AREA IS OPEN)
ALL DIMENSIONS ARE ± .13mm UNLESS OTHERWISE NOTED
recommended PCb solder Pad recommended stencil Pattern(hatched Area is open)
3636
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
36
XLamp® XHp35 LED
tAPE AnD rEEL
All Cree carrier tapes conform to eIA-481D, Automated Component Handling Systems Standard.
except as noted, all dimensions in mm [inches]
XHP35 High DensityXHP35A-0x-xxxx-xxxxxxxxx
XHP35 High Density
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
3456
6 5 4 3 2 1
A
B
C
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6 1/11.000
A2402-00040
Carrier Tape, XPL
5/16/14 D. CRONIN
.30 [.012]T
Ao3.60 [.142]
3.00 [.118]Ko
3.0 °
3.0 °
3.60 [.142]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø1.50+.10-.00
Ø1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZE
Ao - 3.60 mm [.142"]
Bo - 3.60 mm [.142"]
Ko - 3.00 mm [.118"]CATHODE SIDE
ANODE SIDE
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
3456
6 5 4 3 2 1
A
B
C
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6 1/11.000
A2402-00040
Carrier Tape, XPL
5/16/14 D. CRONIN
.30 [.012]T
Ao3.60 [.142]
3.00 [.118]Ko
3.0 °
3.0 °
3.60 [.142]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø1.50+.10-.00
Ø1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZE
Ao - 3.60 mm [.142"]
Bo - 3.60 mm [.142"]
Ko - 3.00 mm [.118"]CATHODE SIDE
ANODE SIDE
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
3456
6 5 4 3 2 1
A
B
C
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6 1/11.000
A2402-00040
Carrier Tape, XPL
5/16/14 D. CRONIN
.30 [.012]T
Ao3.60 [.142]
3.00 [.118]Ko
3.0 °
3.0 °
3.60 [.142]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø1.50+.10-.00
Ø1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZE
Ao - 3.60 mm [.142"]
Bo - 3.60 mm [.142"]
Ko - 3.00 mm [.118"]CATHODE SIDE
ANODE SIDE
SIZE
TITLE
OF
REV.
SHEET
CDRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
3456
6 5 4 3 2 1
A
B
C
Phone (919) 313-5300Fax (919) 313-5558
4600 Silicon DriveDurham, N.C 27703
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENTMAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY ANDCREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °.XXX ± .25.XX ± .75.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125X° ± .5 °
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH: 1.6 1/11.000
A2402-00040
Carrier Tape, XPL
5/16/14 D. CRONIN
.30 [.012]T
Ao3.60 [.142]
3.00 [.118]Ko
3.0 °
3.0 °
3.60 [.142]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø1.50+.10-.00
Ø1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZE
Ao - 3.60 mm [.142"]
Bo - 3.60 mm [.142"]
Ko - 3.00 mm [.118"]CATHODE SIDE
ANODE SIDE
Anode Side
Loaded Pockets(500 Lamps) Leader
400 mm (min.) ofempty pockets with
at least 100 mmsealed by tape
(50 empty pockets min.)
Trailer160 mm (min.) ofempty pockets
sealed with tape(20 pockets min.)
STARTENDUser Feed Direction
Loaded Pockets(1,000 Lamps) Leader
400mm (min) ofempty pockets with
at least 100mmsealed by tape
(50 empty pockets min.)
Trailer160mm (min) ofempty pockets
sealed with tape(20 pockets min.)
STARTEND
Cathode Side
Anode Side(denoted by + and circle)
160.0
A
A
B
2.5±.1
SECTION A-A SCALE 2 : 1
1.5±.1
8.0±.1
4.0±.1
1.75±.10
12.0 .0+.3
DETAIL B SCALE 2 : 1
13mm7"
Cover Tape
Pocket Tape
User Feed Direction
User Feed Direction
3737
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
37
XLamp® XHp35 LED
tAPE AnD rEEL - ContinuED
XHP35 High intensityXHP35A-Hx-xxxx-xxxxxxxxx
XHP35 High Intensity
.30 [.012]T
Ao3.70 [.146]
1.20 [.047]Ko
3.0°
3.0°
3.70 [.146]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø 1.50 +.10 +.0039 -.00[.0591-.0000]Do
Ø 1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZEAo - 3.70 mm [.146"]Bo - 3.70 mm [.146"]Ko - 1.20 mm [.047"]
ANODE SIDE
CATHODE SIDE
.30 [.012]T
Ao3.70 [.146]
1.20 [.047]Ko
3.0°
3.0°
3.70 [.146]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø 1.50 +.10 +.0039 -.00[.0591-.0000]Do
Ø 1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZEAo - 3.70 mm [.146"]Bo - 3.70 mm [.146"]Ko - 1.20 mm [.047"]
ANODE SIDE
CATHODE SIDE
.30 [.012]T
Ao3.70 [.146]
1.20 [.047]Ko
3.0°
3.0°
3.70 [.146]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø 1.50 +.10 +.0039 -.00[.0591-.0000]Do
Ø 1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZEAo - 3.70 mm [.146"]Bo - 3.70 mm [.146"]Ko - 1.20 mm [.047"]
ANODE SIDE
CATHODE SIDE
.30 [.012]T
Ao3.70 [.146]
1.20 [.047]Ko
3.0°
3.0°
3.70 [.146]Bo
10.25[.404]
E2
P22.00 [.079]
Po4.00 [.157]
Ø 1.50 +.10 +.0039 -.00[.0591-.0000]Do
Ø 1.50[.059]D1MIN
12.00 [.472]NOMINAL
12.30 [.484]
MAXW
1.75 [.069]E1
5.50 [.217]F
8.00 [.315]P
POCKET SIZEAo - 3.70 mm [.146"]Bo - 3.70 mm [.146"]Ko - 1.20 mm [.047"]
ANODE SIDE
CATHODE SIDE
Anode Side
Loaded Pockets(1,000 Lamps) Leader
400mm (min) ofempty pockets with
at least 100mmsealed by tape
(50 empty pockets min.)
Trailer160mm (min) ofempty pockets
sealed with tape(20 pockets min.)
STARTEND
Cathode Side
Anode Side(denoted by + and circle)
160.0
A
A
B
2.5±.1
SECTION A-A SCALE 2 : 1
1.5±.1
8.0±.1
4.0±.1
1.75±.10
12.0 .0+.3
DETAIL B SCALE 2 : 1
13mm7"
Cover Tape
Pocket Tape
User Feed Direction
User Feed Direction
3838
Copyright © 2015-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo and SC5 Technology™ are trademarks of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
38
XLamp® XHp35 LED
PACKAging
Patent Label(on bottom of box)
Label with Cree Bin Code, Quantity, Reel ID
Label with Cree Bin Code, Quantity, Reel ID
Label with Cree Order Code, Quantity, Reel ID, PO #
Label with Cree Order Code, Quantity, Reel ID, PO #
Label with Cree Bin Code, Quantity, Reel ID
Unpackaged Reel
Packaged Reel
Boxed Reel
CREE Bin Code& Barcode Label
Vacuum-SealedMoisture Barrier Bag
Label with CustomerP/N, Qty, Lot #, PO #
Label with Cree Bin Code, Qty, Lot #
Label with Cree Bin Code, Qty, Lot #
Vacuum-Sealed Moisture Barrier Bag
Patent Label
Label with Customer Order Code, Qty, Reel ID, PO #