Classic Vinyl Picket Gate
Transcript of Classic Vinyl Picket Gate
REALLY
Classic VinylPicket Gate
Important stuff to know aboutinstalling your WamBam gate.
1-877-778-5733www.wambamfence.com
Ver 1, July 2015
1
1 - Read Over Fence Instructions First Your gate and fence will work better together as an integrated solution if you �rst take the time to read and understand your fence instructions.
2 - Do a Dry Run First on the Gate Frame Only (not pickets or boards) Please do not glue or screw your gate frame together until you have �rst temporarily assembled the gate. In other words, do a dry run �rst.
This will ensure four things:
a) The assembled gate is the correct width as per the product overview drawing.
b) That you have everything necessary to complete the gate.
c) That you will have assembled the gate in the correct order.
d) All the pieces �t and function properly.
It is easier to trouble shoot when things are not screwed together.
3 - Ideally, Install Your Gate Posts Before Your Fence Posts Your fence panels will be more forgiving for a custom �t than your gate. Ideally, position and install your gate posts before you do anything else, or very early on in the process of setting up your fence run.
Install Your Gate Posts Before Installing Your
Fence Posts.
Reality CheckClassic Picket Vinyl Gate
For more information,contact us at 1 877-778-5733.
Con�rm Opening Prior to FinalAssembly of Gate w/Hardware.
2
4 - Ideally, Do Not Hang Your Gate System Off a Single Non-Supported Post. Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is connected to another post. The weight strain will be transferred unto two posts versus just one. Installing fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space restrictions, please contact us for alternative solutions to overcome.
For more information, contact us at 1 877-778-5733.
Do Not Hang Gate on Lone Soldier Post.
Classic Vinyl Picket Gate
PRODUCT OVERVIEW
For more information, contact us at 1 877-778-5733. 3
Ground3.5in.
48in.
7.75in.
24.75in.
4in.
47.5in.
1.5in.
3.5in.3.5in.
1.5in.
2in.
50in.
48in.
48in.
50.5in.
Gate InstallationGate Assembly
B
A B
C D
3.5in.
1.5in.
.090in. wall thickness
C
1.5in.
D
3.5in.
3.5in.A
2.89in.3in.
36in.
Classic Vinyl Picket Gate
2in.Concrete Footing
10in.
Posts Sold Separately
72in.
.090in. wall thickness
4
Each Gate Box Includes:
• Gate Caps (2)
• T-Brackets (2)
• Gate Hinges (2)
• Picket Caps (7)
• Top Rail (1) • Gate Latch (1)
• Vertical Stiles (2)
• Pickets (7)
• Stainless Steel Screws (20)
• Gate Brace (1)
• Bottom Rail (1)
• Gate Bottom Brackets (2)
Sold Separately:
• 6ft. Posts (2-Pack)
Box ContentsClassic Picket Vinyl Gate
.050in. wall thickness
• Tubes of Glue (2)
For more information, contact us at 1 877-778-5733.
Posts Sold Separately as 2-Packs.
For more information, contact us at 1 877-778-5733. 5
Use The Cutting Guide Below To Trim Pickets to Create A Custom Gate Design
ABCD
37 1/8in.40 3/8in.42 3/8in.43 1/8in.
This Gate Can Also Be Trimmed Down Both in Width and Height to Accomodate Custom Applications.B
A
C DB
A
C
Please Note: Cut down the vertical stiles by 6in.
Classic Picket Vinyl Gate
Customize YourGate Design
For more information, contact us at 1 877-778-5733. 6
Completely assembled gate shown
Assemble the Gate Frame Bottom & SidesSTEP 1
GLUE
Handle with care: vinyl weldglue takes approximately
five minutes to cure.
A
Detailed Installation Instructions
Classic Picket Vinyl Gate
C - Insert the bottom rail ALL THE WAY until it BOTTOMS OUT INSIDE GATE BRACKET
D - Insert vertical gate stiles. They willBOTTOM OUT against bottom horizontal rail
C D
B - Insert the bottom rail ALL THE WAY until it BOTTOMS OUT inside gate bracket
BNote that the bottom rail
is ribbed internally.
GLUE
GLUE
Fasten gate brackets to internal members though inside
of frame using screws.
Did you do a dry run of assembly first? Please read page 1 of instructions.
IMPORTANT!
A - Run bead of vinyl weld continously around the inside of the gate bracket
Insert fully to this point.
Insert fully to this point.
For more information, contact us at 1 877-778-5733.7
A
A - Run bead of vinyl-weld continously around the inside of the bracket
E - Slide brackets with toprail attached down over the vertical gate stiles
E - Completely assembled gate frame shown
E F
C - Insert rail ALL THE WAY until it BOTTOMS OUT inside bracket (glue first)
C
Classic Picket Vinyl Gate
Assemble the Gate FrameTop & Attach to Sides
STEP 2
D
D - Run a bead of vinyl-weld continuously around the inside of the brackets
GLUE
GLU
E
GLU
E
Did you do a dry run of assembly first? Please read page 1
of instructions.
B - Insert top rail ALL THE WAY until it BOTTOMS OUT inside bracket
BIMPORTANT!
IMPORTANT!
8
A
A - ENSURE YOUR GATE IS SQUARE and screw brackets as illustrated. The corner-to-corner measurement must be the same, and the width of the gate should be 48”.
Screw Gate Frame/BracketsSTEP 3
Classic Picket Vinyl Gate
48in.
For more information, contact us at 1 877-778-5733. 9
A
A - Insert pickets with tab ends through top rail B - Glue picket caps and attach to top of pickets
C - Glue bracket caps and attach to top of brackets
D - Completed gate with frame shown
C
B
D
Insert Pickets Into GateFrame & Attach CapsSTEP 4
GLUE
GLU
E
Classic Picket Vinyl Gate
For more information, contact us at 1 877-778-5733. 10
A
A - Fasten gate hinges and gate latch onto the gate brackets with screws
Fasten Gate Hinges & Gate LatchSTEP 5
Latch and hinges must beinstalled in these exact locations.
Classic Picket Vinyl Gate
For more information, contact us at 1 877-778-5733. 11
STEP 6
Classic Picket Vinyl Gate
(4) 1.25” (#10)
Screws
(2) .25” Lock Washers
(2).25” Nuts
(2) .25” x .75”Hex Bolts
Gate Brace Parts
B - Re-confirm the gate is square, and screw bracing into place.
A B
Assemble & Fasten Gate Brace
Top Bar Bottom Bar
A - Assemble gate bace with bolts, washers and
nuts as necessary.
1 2 3
For more information, contact us at 1 877-778-5733. 12
A
A - Use temporary spacers or blocks to rest the gate on during alignment and installation
B - Fasten hinges to posts with screws
Position, Adjust & Align Gate/Secure Hinges to PostsSTEP 7
Classic Picket Vinyl Gate
B
Adjust the spring tension in gates as necessary.Use steel insert pin.
LEVEL
13
A
A - Fasten gate hinges accordingly B - Check for level, fit and function to latching post
C
B
D
Level Gate & Adjust HingesSTEP 8
C - Hinges can be adjusted moderately to bring gate into level alignment with post
Latch is designed for left and right hand applications.Temporarily remove the spring, bolt and reversepaddle portion as necessary.
Classic Picket Vinyl Gate
For more information, contact us at 1 877-778-5733. 14
A
A - Align and fasten the gate latch catch to fit and function with the gate finger.
B
Align & Install LatchSTEP 9
Congratulations! You did it!Go grab a beverage of your choice, admire your
handy work, and show us what you got by enteringour annual photo/video contests!
Classic Picket Vinyl Gate