Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping...

28
Tool Holders, Drilling, Milling & CNC Accessories Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining & EDM

Transcript of Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping...

Page 1: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

Tool Holders, Drilling, Milling & CNC Accessories

Clamping Devices, Clamping Elements

All Products Catalogue 2016

Chucks for Production Machining & EDM

Page 2: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

This catalogue has all the products that Abbott Toolfast offers with minor essential details.

For more details you may contact us for detailed catalogues or visit company websites.

C O N T E N T S

TOOLFAST is a registered trade mark of our company and all TOOLFAST

products are manufactured by us. Other products illustrated in this catalogue

are all world renowned products marketed by us in India.

Page - 14-15

Page - 16

.............................................................

..............................................

World Renowned Modular Vices

World Renowned Angle Heads And Other Products

Machining Centre Vices And Drill Grinding Machine Page - 17............................................

Milling And CNC Accessories Page - 18..................................................................................

Precision Micro Boring Heads And Sets Page - 19................................................................

Grinding, EDM Accessories and other GIN Products Page - 20-23...........................................

Drilling, Milling and CNC Accessories Page - 24-25...................................................................

Fixture Clamps And Pallets Page - 9-10.....................................................................................Vacmagic - Pallet Changer And Vacuum Chuck

Chucks For Production Machining, EDM and WIRECUT EDM Page - 26...........................

Clamping Devices And Clamping Elements Page - 4-7..........................................................

Wedge Clamps Page - 8........................................................................................................

Page - 11-12.......................................................................Milling And Grinding Accessories

Milling And Machining Center Vices Page - 13.......................................................................

Page 3: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

This catalogue has all the products that Abbott Toolfast offers with minor essential details.

For more details you may contact us for detailed catalogues or visit company websites.

C O N T E N T S

TOOLFAST is a registered trade mark of our company and all TOOLFAST

products are manufactured by us. Other products illustrated in this catalogue

are all world renowned products marketed by us in India.

Page - 14-15

Page - 16

.............................................................

..............................................

World Renowned Modular Vices

World Renowned Angle Heads And Other Products

Machining Centre Vices And Drill Grinding Machine Page - 17............................................

Milling And CNC Accessories Page - 18..................................................................................

Precision Micro Boring Heads And Sets Page - 19................................................................

Grinding, EDM Accessories and other GIN Products Page - 20-23...........................................

Drilling, Milling and CNC Accessories Page - 24-25...................................................................

Fixture Clamps And Pallets Page - 9-10.....................................................................................Vacmagic - Pallet Changer And Vacuum Chuck

Chucks For Production Machining, EDM and WIRECUT EDM Page - 26...........................

Clamping Devices And Clamping Elements Page - 4-7..........................................................

Wedge Clamps Page - 8........................................................................................................

Page - 11-12.......................................................................Milling And Grinding Accessories

Milling And Machining Center Vices Page - 13.......................................................................

Page 4: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

CLAMPING DEVICES AND CLAMPING ELEMENTS

USC-12(a)USC-12(b)USC-16(a)USC-16(b)USC-20(a)USC-20(b)USC-24(a)USC-24(b)

1214161820222428

0-60 0-60 0-80 0-80

0-100 0-100 0-120 0-120

MODELSUITABLE FOR T-SLOT SIZE

CLAMPING RANGE

UNIVERSAL STRAP CLAMP

For power presses, milling, drilling, shaping and boring. Supplied complete with

T-Bolt, Nut etc.

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

For mould clamping on plastic injection moulding & pressure die casting machines.

Supplied complete with T-Bolt or Stud and Nut etc.

MOULD CLAMP - WITH CLAMPING STUD

MC-12MC-16MC-20MC-24

0-350-400-500-60

STUD M-12 x 1.75 x 100STUD M-16 x 2.0 x 125STUD M-20 x 2.5 x 175STUD M-24 x 3.0 x 200

MODEL DIA x PITCH x LENGTHCLAMPING

HEIGHTRANGE

MOULD CLAMP - WITH T- BOLT

MC-12(a)MC-12(b)MC-16(a)MC-16(b)MC-20(a)MC-20(b)MC-24(a)MC-24(b)

1214161820222428

0-35 0-35 0-40 0-40 0-50 0-50 0-60 0-60

CLAMPINGHEIGHTRANGE

MODELSUITABLE FOR

T-SLOT SIZE

MOULD CLAMP

TAPPED END CLAMP WITH ADJUSTABLE SUPPORT

For mould clamping on plastic injection moulding & pressure die casting machines.

Supplied only with threaded support.

TTUC-12TTUC-16TTUC-20TTUC-24

M-12M-16M-20M-24

SUITABLE FOR BOLTMODEL

110125160200

LENGTH

LOW HEIGHT PINCH CLAMP

For side clamping on VMC, milling, shaping, planning, jig boring etc.

MODEL

PC-1(a)PC-1(b)PC-2PC-3PC-4(a)PC-4(b)PC-5(a)PC-5(b)

1214161820222428

SUITABLE FOR T-SLOT SIZE

1515181824242424

CLAMP THICKNESS

TOTALLENGTH

115115145145180180180180

HEAVY DUTY PINCH CLAMP

For side clamping of thicker plates on VMC, milling, planning, plano-milling etc.

MODELSUITABLE FOR

T-SLOT SIZE

HDPC-1(a)HDPC-1(b)HDPC-2(a)HDPC-2(b)HDPC-3

1820222428

CLAMPTHICKNESS

3838383838

185185185185185

TOTALLENGTH

FORGED STRAP CLAMP WITH TAPPED END

Most suitable for mould clamping on Plastic Injection Moulding Machine.

Forged, Hardened & Tempered

TTFC -16 M-16

MODELSUITABLE FOR BOLT

152

TOTAL LENGTH

M -16

TAPPED END

Also available as Model TTFC-16S with threaded support TS-16 (M-16X70 Long).

'TOOLFAST' mould clamp is now available in forged steel body for extra strength.

MOULD CLAMP - WITH CLAMPING STUD

MCF-12MCF-16MCF-20MCF-24

0-350-500-650-75

STUD M-12 x 1.75 x 100STUD M-16 x 2.0 x 125STUD M-20 x 2.5 x 175STUD M-24 x 3.0 x 200

MODEL DIA x PITCH x LENGTHCLAMPING

RANGE

MOULD CLAMP - WITH T- BOLT

MCF-12(a)MCF-12(b)MCF-16(a)MCF-16(b)MCF-20(a)MCF-20(b)MCF-24(a)MCF-24(b)

1214161820222428

0-35 0-35 0-50 0-50 0-65 0-65 0-75 0-75

CLAMPINGHEIGHTRANGE

MODELSUITABLE FOR

T-SLOT SIZE

MOULD CLAMP - FORGED

COMPACT MILLING CLAMP

The most multi-purpose, quick and easy to use down-hold milling clamp.

MODEL

CMC-12CMC-14CMC-16CMC-18

0-1250-1250-1250-125

CLAMPING HEIGHT RANGE

12141618

SUITABLE FOR

T-SLOT SIZE

1600kgs.1600kgs.1600kgs.1600kgs.

HEIGHT BLOCK FOR CMC CLAMP :

By stacking one Height block over another and a CMC clamp at the top can enable clamping of any height of workpiece. Each height block modelHB-CMC-75 increases clamping height range by 75mm.

Height Block HB-CMC-75

New Forged

Steel Body

ST-PC-1AST-PC-1BST-PC-2ST-PC-3ST-PC-4AST-PC-4BST-PC-5AST-PC-5BST-HDPC-1AST-HDPC-1BST-HDPC-2AST-HDPC-2BST-HDPC-3

15151818242424243838383838

THICKNESSMODELSUITABLE

FOR PINCH CLAMP MODEL

PC-1(a)PC-1(b)

PC-2PC-3

PC-4(a)PC-4(b)PC-5(a)PC-5(b)

HDPC-1(a)HDPC-1(b)HDPC-2(a)HDPC-2(b)

HDPC-3

STOP FOR PINCH CLAMPS

PCS-1APCS-1BPCS-2PCS-3

12141618

55556666959595959595959595

TOTAL LENGTH

LOW HEIGHT PINCH CLAMP AND STOP WITH STEP

Stop For Above Pinch Clamp With Step

Low Height Pinch Clamp With Step

Stop or Stopper block to be mounted on the opposite side of workpiece while clamping with PC Series or HDPC series pinch clamps.

This is a new version of low height pinch clamp (PC Series) having step to support the workpiece above the machine table for through milling and drilling.

MINI PINCH CLAMP

For side clamping of thin plates on VMC, milling, shaping & planning.

MPC-1MPC-2MPC-3

141618

MODEL SUITABLE FOR T-SLOT SIZE

MODE

New

New

4

CLAMPS AND CLAMPING ELEMENTS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

MODEL

ADJUSTABLE SUPPORT PLATES

TASP-250

TASP-2100

TASP-2150

TASP-L-250

TASP-L-2100

TASP-L-2150

50

100

150

50

100

150

MAXIMUM HEIGHT

For clamp support.

25 X 35

25 X 35

25 X 35

35 X 50

35 X 50

35 X 50

CLAMP RESTAREA

2

2

2

2

2

2

PLATETHICKNESS

THREADED SUPPORT FOR TAPPED END CLAMPS

These have large resting base and hexagon at bottom for

height adjustment.

STRAP CLAMP - FORGED BODY

M-12

M-16

M-20

M-24

120

140

180

220

MODEL SUITABLE FOR BOLT

TOTALLENGTH

TSCF-12TSCF-16TSCF-20TSCF-24

Hardened & tempered, tapped end.

STRAP CLAMP Hardened & tempered, Black Finish based on IS:4292

MODEL

TSC-8-60TSC-10-80TSC-12-100TSC-12-125TSC-14-125TSC-16-125TSC-16-160TSC-20-160TSC-24-200TSC-30-250

M-8M-10M-12M-12M-14M-16M-16M-20M-24M-30

6080100125125125160160200250

SUITABLE FOR BOLT LENGTH

GOOSE NECK CLAMP- FORGED - TAPPED END

TGNCF-12TGNCF-16TGNCF-20TGNCF-24

M-12M-16M-20M-24

125125165200

MODEL SUITABLE FOR BOLT LENGTH

PLAIN CLAMP

M-12

M-16

70

90

MODEL SUITABLE FOR BOLT

TOTALLENGTH

TES-12TES-16

Hardened & Tempered

These are economy models of strap clamps. Can be used where simple shape of a plain strap can serve the purpose.

STEPPED STRAP CLAMP Hardened & Tempered, Black Finish

To be used with step block.

TSSC-12-65TSSC-12-100TSSC-12-125TSSC-16-75TSSC-16-125TSSC-16-160TSSC-20-160TSSC-24-200

M-12M-12M-12M-16M-16M-16M-20M-24

6510012575

125160160200

MODEL SUITABLE FOR BOLT LENGTH

U - CLAMP Hardened & Tempered, black nish based on IS:4293

MODEL SUITABLE FOR BOLT LENGTH

TUC-12-160TUC-16-200TUC-20-250TUC-24-250

M-12M-16M-20M-24

160200250250

FINGER STRAP CLAMP

TCF -16 M-16

MODEL SUITABLE FOR BOLT

152

TOTAL LENGTH

Forged, Hardened & Tempered

CAM CLAMP Hold Down Type

Most ideal for quick Hold Down Clamping in xtures. Conventional Strap Clamps in

xtures can be replaced by these quick acting Cam clamps without much effort.

These clamps have high clamping force suitable for machining xtures.

MODEL CLAMPING BOLT HOLDING CAPACITY

TCC-10

TCC-12

M-10

M-12

1400 Kgs.

2000 Kgs.

TS-12TS-16TS-20TS-24

M-12 x 1.75 PM-16 x 2.0 PM-20 x 2.5 PM-24 x 3.0 P

60708085

30354050

DIA AT BOTTOM

THREAD SIZE

OVERALL LENGTH

MODEL

LEVELLING JACK - HEAVY DUTY

LEVELLING JACKS & HEIGHT BLOCKS

LEVELLING JACK

LJ-HD 160 230 FLAT 50Ø

MODELMIN.

HEIGHTMAX.

HEIGHTTYPE OF

TOP FACE

HEIGHT BLOCK FOR LEVELLING JACK

HBLJ-75 75

MODELEFFECTIVE HEIGHT INCREASE

WITH ONE HEIGHT BLOCK

HIGHT BLOCK FOR LEVELLING JACK - HEAVY DUTY

HBLJ-HD-75 75

MODELEFFECTIVE HEIGHT INCREASE

WITH ONE HEIGHT BLOCK

32Ø

SCREWTHREAD

LEVELLING JACK - HEAVY DUTY FLANGE MOUNTING

LJ-HD-FB 160 230 FLAT 50Ø

MODEL MIN.

HEIGHT MAX.

HEIGHTTYPE OF

TOP FACE

32Ø

SCREWTHREAD

MODEL

STEP BLOCKS

STEP BLOCK

TSB-1L

TSB-1

TSB-2L

TSB-2

TSB-3L

TSB-3

24

30

24

30

24

30

20

20

40

40

60

60

44

44

100

100

155

155

MAXIMUMMINIMUM

HEIGHT ADJUSTMENTWIDTH

MODEL

STEP BLOCK - HEAVY DUTY

MAXIMUMMINIMUM

HEIGHT ADJUSTMENTWIDTH

THSB-5THSB-6

4848

4072

100180

For clamp support.

MODEL

LJ-1(a)LJ-1(b)LJ-2LJ-3

75100120105

100150170155

FLAT 38ØFLAT 38ØCONICAL

‘V’

M-24M-24M-24M-24

MIN. HEIGHT

MAX. HEIGHT

TYPE OF TOP FACE

SCREWTHREAD

MAX.LOAD TONS

5.05.05.05.0

MAX.LOAD TONS

8.0

MAX.LOAD TONS

8.0

2D / 3D CAD les available on request

SCREW JACK - HEAVY DUTY

MODEL

SJ-HD-1SJ-HD-2

250380

400660

FLAT 75ØFLAT 75Ø

40Ø40Ø

MIN. HEIGHT

MAX. HEIGHT

TYPE OF TOP FACE

SCREWTHREAD

MAX.LOAD TONS

2525

5

HEIGHT

SUITABLE FOR T-SLOT SIZE

CLAMPING FORCE

Page 5: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

CLAMPING DEVICES AND CLAMPING ELEMENTS

USC-12(a)USC-12(b)USC-16(a)USC-16(b)USC-20(a)USC-20(b)USC-24(a)USC-24(b)

1214161820222428

0-60 0-60 0-80 0-80

0-100 0-100 0-120 0-120

MODELSUITABLE FOR T-SLOT SIZE

CLAMPING RANGE

UNIVERSAL STRAP CLAMP

For power presses, milling, drilling, shaping and boring. Supplied complete with

T-Bolt, Nut etc.

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

For mould clamping on plastic injection moulding & pressure die casting machines.

Supplied complete with T-Bolt or Stud and Nut etc.

MOULD CLAMP - WITH CLAMPING STUD

MC-12MC-16MC-20MC-24

0-350-400-500-60

STUD M-12 x 1.75 x 100STUD M-16 x 2.0 x 125STUD M-20 x 2.5 x 175STUD M-24 x 3.0 x 200

MODEL DIA x PITCH x LENGTHCLAMPING

HEIGHTRANGE

MOULD CLAMP - WITH T- BOLT

MC-12(a)MC-12(b)MC-16(a)MC-16(b)MC-20(a)MC-20(b)MC-24(a)MC-24(b)

1214161820222428

0-35 0-35 0-40 0-40 0-50 0-50 0-60 0-60

CLAMPINGHEIGHTRANGE

MODELSUITABLE FOR

T-SLOT SIZE

MOULD CLAMP

TAPPED END CLAMP WITH ADJUSTABLE SUPPORT

For mould clamping on plastic injection moulding & pressure die casting machines.

Supplied only with threaded support.

TTUC-12TTUC-16TTUC-20TTUC-24

M-12M-16M-20M-24

SUITABLE FOR BOLTMODEL

110125160200

LENGTH

LOW HEIGHT PINCH CLAMP

For side clamping on VMC, milling, shaping, planning, jig boring etc.

MODEL

PC-1(a)PC-1(b)PC-2PC-3PC-4(a)PC-4(b)PC-5(a)PC-5(b)

1214161820222428

SUITABLE FOR T-SLOT SIZE

1515181824242424

CLAMP THICKNESS

TOTALLENGTH

115115145145180180180180

HEAVY DUTY PINCH CLAMP

For side clamping of thicker plates on VMC, milling, planning, plano-milling etc.

MODELSUITABLE FOR

T-SLOT SIZE

HDPC-1(a)HDPC-1(b)HDPC-2(a)HDPC-2(b)HDPC-3

1820222428

CLAMPTHICKNESS

3838383838

185185185185185

TOTALLENGTH

FORGED STRAP CLAMP WITH TAPPED END

Most suitable for mould clamping on Plastic Injection Moulding Machine.

Forged, Hardened & Tempered

TTFC -16 M-16

MODELSUITABLE FOR BOLT

152

TOTAL LENGTH

M -16

TAPPED END

Also available as Model TTFC-16S with threaded support TS-16 (M-16X70 Long).

'TOOLFAST' mould clamp is now available in forged steel body for extra strength.

MOULD CLAMP - WITH CLAMPING STUD

MCF-12MCF-16MCF-20MCF-24

0-350-500-650-75

STUD M-12 x 1.75 x 100STUD M-16 x 2.0 x 125STUD M-20 x 2.5 x 175STUD M-24 x 3.0 x 200

MODEL DIA x PITCH x LENGTHCLAMPING

RANGE

MOULD CLAMP - WITH T- BOLT

MCF-12(a)MCF-12(b)MCF-16(a)MCF-16(b)MCF-20(a)MCF-20(b)MCF-24(a)MCF-24(b)

1214161820222428

0-35 0-35 0-50 0-50 0-65 0-65 0-75 0-75

CLAMPINGHEIGHTRANGE

MODELSUITABLE FOR

T-SLOT SIZE

MOULD CLAMP - FORGED

COMPACT MILLING CLAMP

The most multi-purpose, quick and easy to use down-hold milling clamp.

MODEL

CMC-12CMC-14CMC-16CMC-18

0-1250-1250-1250-125

CLAMPING HEIGHT RANGE

12141618

SUITABLE FOR

T-SLOT SIZE

1600kgs.1600kgs.1600kgs.1600kgs.

HEIGHT BLOCK FOR CMC CLAMP :

By stacking one Height block over another and a CMC clamp at the top can enable clamping of any height of workpiece. Each height block modelHB-CMC-75 increases clamping height range by 75mm.

Height Block HB-CMC-75

New Forged

Steel Body

ST-PC-1AST-PC-1BST-PC-2ST-PC-3ST-PC-4AST-PC-4BST-PC-5AST-PC-5BST-HDPC-1AST-HDPC-1BST-HDPC-2AST-HDPC-2BST-HDPC-3

15151818242424243838383838

THICKNESSMODELSUITABLE

FOR PINCH CLAMP MODEL

PC-1(a)PC-1(b)

PC-2PC-3

PC-4(a)PC-4(b)PC-5(a)PC-5(b)

HDPC-1(a)HDPC-1(b)HDPC-2(a)HDPC-2(b)

HDPC-3

STOP FOR PINCH CLAMPS

PCS-1APCS-1BPCS-2PCS-3

12141618

55556666959595959595959595

TOTAL LENGTH

LOW HEIGHT PINCH CLAMP AND STOP WITH STEP

Stop For Above Pinch Clamp With Step

Low Height Pinch Clamp With Step

Stop or Stopper block to be mounted on the opposite side of workpiece while clamping with PC Series or HDPC series pinch clamps.

This is a new version of low height pinch clamp (PC Series) having step to support the workpiece above the machine table for through milling and drilling.

MINI PINCH CLAMP

For side clamping of thin plates on VMC, milling, shaping & planning.

MPC-1MPC-2MPC-3

141618

MODEL SUITABLE FOR T-SLOT SIZE

MODE

New

New

4

CLAMPS AND CLAMPING ELEMENTS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

MODEL

ADJUSTABLE SUPPORT PLATES

TASP-250

TASP-2100

TASP-2150

TASP-L-250

TASP-L-2100

TASP-L-2150

50

100

150

50

100

150

MAXIMUM HEIGHT

For clamp support.

25 X 35

25 X 35

25 X 35

35 X 50

35 X 50

35 X 50

CLAMP RESTAREA

2

2

2

2

2

2

PLATETHICKNESS

THREADED SUPPORT FOR TAPPED END CLAMPS

These have large resting base and hexagon at bottom for

height adjustment.

STRAP CLAMP - FORGED BODY

M-12

M-16

M-20

M-24

120

140

180

220

MODEL SUITABLE FOR BOLT

TOTALLENGTH

TSCF-12TSCF-16TSCF-20TSCF-24

Hardened & tempered, tapped end.

STRAP CLAMP Hardened & tempered, Black Finish based on IS:4292

MODEL

TSC-8-60TSC-10-80TSC-12-100TSC-12-125TSC-14-125TSC-16-125TSC-16-160TSC-20-160TSC-24-200TSC-30-250

M-8M-10M-12M-12M-14M-16M-16M-20M-24M-30

6080100125125125160160200250

SUITABLE FOR BOLT LENGTH

GOOSE NECK CLAMP- FORGED - TAPPED END

TGNCF-12TGNCF-16TGNCF-20TGNCF-24

M-12M-16M-20M-24

125125165200

MODEL SUITABLE FOR BOLT LENGTH

PLAIN CLAMP

M-12

M-16

70

90

MODEL SUITABLE FOR BOLT

TOTALLENGTH

TES-12TES-16

Hardened & Tempered

These are economy models of strap clamps. Can be used where simple shape of a plain strap can serve the purpose.

STEPPED STRAP CLAMP Hardened & Tempered, Black Finish

To be used with step block.

TSSC-12-65TSSC-12-100TSSC-12-125TSSC-16-75TSSC-16-125TSSC-16-160TSSC-20-160TSSC-24-200

M-12M-12M-12M-16M-16M-16M-20M-24

6510012575

125160160200

MODEL SUITABLE FOR BOLT LENGTH

U - CLAMP Hardened & Tempered, black nish based on IS:4293

MODEL SUITABLE FOR BOLT LENGTH

TUC-12-160TUC-16-200TUC-20-250TUC-24-250

M-12M-16M-20M-24

160200250250

FINGER STRAP CLAMP

TCF -16 M-16

MODEL SUITABLE FOR BOLT

152

TOTAL LENGTH

Forged, Hardened & Tempered

CAM CLAMP Hold Down Type

Most ideal for quick Hold Down Clamping in xtures. Conventional Strap Clamps in

xtures can be replaced by these quick acting Cam clamps without much effort.

These clamps have high clamping force suitable for machining xtures.

MODEL CLAMPING BOLT HOLDING CAPACITY

TCC-10

TCC-12

M-10

M-12

1400 Kgs.

2000 Kgs.

TS-12TS-16TS-20TS-24

M-12 x 1.75 PM-16 x 2.0 PM-20 x 2.5 PM-24 x 3.0 P

60708085

30354050

DIA AT BOTTOM

THREAD SIZE

OVERALL LENGTH

MODEL

LEVELLING JACK - HEAVY DUTY

LEVELLING JACKS & HEIGHT BLOCKS

LEVELLING JACK

LJ-HD 160 230 FLAT 50Ø

MODELMIN.

HEIGHTMAX.

HEIGHTTYPE OF

TOP FACE

HEIGHT BLOCK FOR LEVELLING JACK

HBLJ-75 75

MODELEFFECTIVE HEIGHT INCREASE

WITH ONE HEIGHT BLOCK

HIGHT BLOCK FOR LEVELLING JACK - HEAVY DUTY

HBLJ-HD-75 75

MODELEFFECTIVE HEIGHT INCREASE

WITH ONE HEIGHT BLOCK

32Ø

SCREWTHREAD

LEVELLING JACK - HEAVY DUTY FLANGE MOUNTING

LJ-HD-FB 160 230 FLAT 50Ø

MODEL MIN.

HEIGHT MAX.

HEIGHTTYPE OF

TOP FACE

32Ø

SCREWTHREAD

MODEL

STEP BLOCKS

STEP BLOCK

TSB-1L

TSB-1

TSB-2L

TSB-2

TSB-3L

TSB-3

24

30

24

30

24

30

20

20

40

40

60

60

44

44

100

100

155

155

MAXIMUMMINIMUM

HEIGHT ADJUSTMENTWIDTH

MODEL

STEP BLOCK - HEAVY DUTY

MAXIMUMMINIMUM

HEIGHT ADJUSTMENTWIDTH

THSB-5THSB-6

4848

4072

100180

For clamp support.

MODEL

LJ-1(a)LJ-1(b)LJ-2LJ-3

75100120105

100150170155

FLAT 38ØFLAT 38ØCONICAL

‘V’

M-24M-24M-24M-24

MIN. HEIGHT

MAX. HEIGHT

TYPE OF TOP FACE

SCREWTHREAD

MAX.LOAD TONS

5.05.05.05.0

MAX.LOAD TONS

8.0

MAX.LOAD TONS

8.0

2D / 3D CAD les available on request

SCREW JACK - HEAVY DUTY

MODEL

SJ-HD-1SJ-HD-2

250380

400660

FLAT 75ØFLAT 75Ø

40Ø40Ø

MIN. HEIGHT

MAX. HEIGHT

TYPE OF TOP FACE

SCREWTHREAD

MAX.LOAD TONS

2525

5

HEIGHT

SUITABLE FOR T-SLOT SIZE

CLAMPING FORCE

Page 6: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

MODEL THREAD SIZE TOTAL

LENGTH

These nuts have longer life as they have more number of threads than ordinary nuts.

EXTRA LONG NUT Hardened & Tempered, Black Finish

TELN-8

TELN-10

TELN-12

TELN-14

TELN-16

TELN-20

TELN-24

TELN-30

M-8

M-10

M-12

M-14

M-16

M-20

M-24

M-30

12

15

18

21

24

30

36

45

T-BOLT Forged Head, Hardened & Tempered, High Tensile Steel, Black Finish

MODEL LENGTHL

80

100

160

60

80

100

125

160

200

80

130

200

80

100

130

160

200

250

290

110

150

210

110

150

210

285

150

210

110

150

210

250

300

200

250

300

THREADSIZE

M12

M12

SUITABLE FOR

T-SLOT SIZE

12

14

TTB-1212-80

TTB-1212-100

TTB-1212-160

TTB-1214-60

TTB-1214-80

TTB-1214-100

TTB-1214-125

TTB-1214-160

TTB-1214-200

TTB-1616-80

TTB-1616-130

TTB-1616-200

TTB-1618-80

TTB-1618-100

TTB-1618-130

TTB-1618-160

TTB-1618-200

TTB-1618-250

TTB-1618-290

TTB-2020-110

TTB-2020-150

TTB-2020-210

TTB-2022-110

TTB-2022-150

TTB-2022-210

TTB-2022-285

TTB-2424-150

TTB-2424-210

TTB-2428-110

TTB-2428-150

TTB-2428-210

TTB-2428-250

TTB-2428-300

TTB-3036-200

TTB-3036-250

TTB-3036-300

SIZEE

18

22

M1616 25

M1618 28

M2020 32

M2022 35

M2424 40

M24 28 44

M3036 54

E

L

MODELTHREAD

SIZETOTAL

LENGTH

CLAMPING STUD Hardend & Tempered, High Tensile Steel, Black Finish

TCSB-12-100

TCSB-12-125

TCSB-12-150

TCSB-12-175

TCSB-16-125

TCSB-16-150

TCSB-16-175

TCSB-16-200

TCSB-20-150

TCSB-20-175

TCSB-20-200

TCSB-24-175

TCSB-24-200

TCSB-24-225

100

125

150

175

125

150

175

200

150

175

200

175

200

225

M-12

M-16

M-20

M-24

With hex key hole at top face for use on machine beds having tapped holes.

THREADLENGTH

30 X 40

30 X 50

30 X 65

30 X 80

40 X 50

40 X 65

40 X 80

40 X 100

50 X 60

50 X 70

50 X 80

60 X 70

60 X 80

60 X 90

CLAMPING STUD Hardend & Tempered, High Tensile Steel, Black Finish

For use with T-nuts.

MODELTHREAD

SIZETOTAL

LENGTHTHREADLENGTH

TCS-8-75

TCS-8-100

TCS-8-150

TCS-10-75

TCS-10-100

TCS-10-125

TCS-10-150

TCS-10-175

TCS-10-200

TCS-12-75

TCS-12-100

TCS-12-125

TCS-12-150

TCS-12-175

TCS-12-200

TCS-12-250

TCS-12-300

TCS-14-100

TCS-14-150

TCS-14-200

TCS-14-250

TCS-16-75

TCS-16-100

TCS-16-125

TCS-16-150

TCS-16-175

TCS-16-200

TCS-16-250

TCS-16-300

TCS-20-100

TCS-20-150

TCS-20-200

TCS-20-250

TCS-20-300

TCS-20-400

TCS-20-500

TCS-24-150

TCS-24-200

TCS-24-250

TCS-24-300

TCS-24-400

TCS-24-500

TCS-30-150

TCS-30-200

TCS-30-250

TCS-30-300

TCS-30-400

TCS-30-500

75

100

150

75

100

125

150

175

200

75

100

125

150

175

200

250

300

100

150

200

250

75

100

125

150

175

200

250

300

100

150

200

250

300

400

500

150

200

250

300

400

500

150

200

250

300

400

500

M-8

M-10

M-12

M-14

M-16

M-20

11 X 48

11 X 63

11 X 95

13 X 48

13 X 63

13 X 75

13 X 95

13 X 110

13 X 125

15 X 48

15 X 63

15 X 75

15 X 95

15 X 110

15 X 125

15 X 160

15 X 190

17 X 63

17 X 95

17 X 125

17 X 160

19 X 50

19 X 63

19 X 75

19 X 95

19 X 110

19 X 125

19 X 160

19 X 190

27 X 60

27 X 95

27 X 125

27 X 160

27 X 190

27 X 250

27 X 250

35 X 95

35 X 120

35 X 160

35 X 190

35 X 250

35 X 250

43 X 95

43 X 120

43 X 160

43 X 190

43 X 250

43 X 250

M-24

M-30

MODELTHREAD

SIZESUITABLE FOR T-SLOT SIZE

T- NUT Hardened & Tempered, Black Finish based on IS:2015

TTN-10-8

TTN-12-10*

TTN-14-10

TTN-14-12*

TTN-16-12

TTN-16-14*

TTN-18-12

TTN-18-16*

TTN-20-16

TTN-22-16

TTN-22-20*

TTN-24-20

TTN-28-24

TTN-36-24

TTN-36-30

10

12

14

14

16

16

18

18

20

22

22

24

28

36

36

15

18

22

22

25

25

28

28

32

35

35

40

44

54

54

M-8

M-10

M-10

M-12

M-12

M-14

M-12

M-16

M-16

M-16

M-20

M-20

M-24

M-24

M-30

S

SIZES

* marked models are not recommended for heavy duty use because of less wall

thickness outside the threading.

CLAMPS AND CLAMPING ELEMENTS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

Knurled outside diameter for easy gripping while quick insertion or removal.

C-WASHER Case Hardened, Ground Faces, Black Finish

MODELSUITABLE

FOR BOLT

TCW-10TCW-12TCW-14TCW-16TCW-20TCW-24TCW-30

M-10M-12 M-14M-16M-20M-24M-30

based on IS : 4291

THICKNESS

991111111114

OUTSIDE

DIA

4048636380

100100

PLAIN WASHER Case Hardened, Black Finish based on IS : 4291

TPW-8TPW-10TPW-12TPW-14TPW-16TPW-20TPW-24TPW-30

M-8M-10M-12M-14M-16M-20M-24M-30

MODELSUITABLE FOR

BOLT

445677911

THICKNESSOUTSIDE

DIA

2328354045486070

Consists of :T-Nuts : 6 Nos.Clamping Studs of six different lengths : 4 Nos. eachFlanged Nuts : 6 Nos.Extension Nuts : 4 Nos.Stepped Strap Clamps of three different lengths : 2 Nos. each Step blocks of three different sizes : 2 pairs (4 Nos.) each

CLAMPING KIT - 58 PIECE with step blocks & stepped strap clamps

TCK-58-1412TCK-58-1612L

TCK-58-1210TCK-58-1410TCK-58-1412L

M-12M-12

M-10M-10M-12

1312

99

12

TCK-58-1612TCK-58-1812TCK-58-1816TCK-58-2016TCK-58-2216

1416

121414

1618182022

M-12M-12M-16M-16M-16

1313181819

MODEL SUITABLE FOR T-SLOT SIZE N.W. Kgs.

Also Included T-Slot

Cleaner FFFREE

CLAMPING KIT - 34 PIECE with adjustable support plates & strap clamps

141618

M-12M-12M-12

TCK-34-1412TCK-34-1612TCK-34-1812

MODEL SUITABLE FOR T-SLOT SIZE THREAD SIZE

Consists of :

T-Nuts : 4 nos.Clamping Studs of four different lengths : 4 nos. eachFlanged Nuts : 4 nos.Extension Nuts : 2 nos.Strap Clamps of two different lengths : 2 nos. eachAdjustable Support Plates of two different sizes : 2 nos. each

CMM CLAMPING KIT - 62 PIECE with Aluminum / plastic clamping elements

Specially designed for 3D coordinate measuring machine and other inspection and gaging applications.

Model CMMCK-62 consists of :

28 nos. Aluminum M-8 studs of different lengths upto 200mm long.8 nos. M-8 Aluminum anged nuts (Hand Tightening Type).6 nos. Aluminum alloy strap clamps.8 nos. Aluminum screw jacks.4 nos. Aluminum top rest pads for screw jacks.8 nos. Plastic bottom rest pads for screw jacks and studs.

Adaptor available on request for CMM’s with M-10 or M-12 threaded beds.

New

EXTENSION NUT Hardened & Tempered, Black Finish

These nuts are used to couple the studs with studs or T- bolts in order to increase their length.

TEN-8TEN-10TEN-12TEN-14TEN-16TEN-20TEN-24TEN-30

M-8M-10M-12 M-14M-16M-20M-24M-30

2430364248607290

MODEL THREAD SIZE TOTAL LENGTH

FLANGED NUT Forged, Hardened & Tempered, Black Finish

These nuts have anged face for larger face contact with the surface to be tightened on.

TFN-12TFN-16TFN-20TFN-24

18243036

M-12M-16M-20M-24

MODEL THREAD SIZE TOTAL

LENGTH

Also Included T-Slot

Cleaner FFFREE

Visit for online details of above products or write to us for a print copy www.toolfastclamps.com

CLAMPS AND CLAMPING ELEMENTS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

7

THREAD SIZE

T-Slot size mentioned in these pages is size ‘A’ of the T-Slot as shown here.A

Page 7: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

MODEL THREAD SIZE TOTAL

LENGTH

These nuts have longer life as they have more number of threads than ordinary nuts.

EXTRA LONG NUT Hardened & Tempered, Black Finish

TELN-8

TELN-10

TELN-12

TELN-14

TELN-16

TELN-20

TELN-24

TELN-30

M-8

M-10

M-12

M-14

M-16

M-20

M-24

M-30

12

15

18

21

24

30

36

45

T-BOLT Forged Head, Hardened & Tempered, High Tensile Steel, Black Finish

MODEL LENGTHL

80

100

160

60

80

100

125

160

200

80

130

200

80

100

130

160

200

250

290

110

150

210

110

150

210

285

150

210

110

150

210

250

300

200

250

300

THREADSIZE

M12

M12

SUITABLE FOR

T-SLOT SIZE

12

14

TTB-1212-80

TTB-1212-100

TTB-1212-160

TTB-1214-60

TTB-1214-80

TTB-1214-100

TTB-1214-125

TTB-1214-160

TTB-1214-200

TTB-1616-80

TTB-1616-130

TTB-1616-200

TTB-1618-80

TTB-1618-100

TTB-1618-130

TTB-1618-160

TTB-1618-200

TTB-1618-250

TTB-1618-290

TTB-2020-110

TTB-2020-150

TTB-2020-210

TTB-2022-110

TTB-2022-150

TTB-2022-210

TTB-2022-285

TTB-2424-150

TTB-2424-210

TTB-2428-110

TTB-2428-150

TTB-2428-210

TTB-2428-250

TTB-2428-300

TTB-3036-200

TTB-3036-250

TTB-3036-300

SIZEE

18

22

M1616 25

M1618 28

M2020 32

M2022 35

M2424 40

M24 28 44

M3036 54

E

L

MODELTHREAD

SIZETOTAL

LENGTH

CLAMPING STUD Hardend & Tempered, High Tensile Steel, Black Finish

TCSB-12-100

TCSB-12-125

TCSB-12-150

TCSB-12-175

TCSB-16-125

TCSB-16-150

TCSB-16-175

TCSB-16-200

TCSB-20-150

TCSB-20-175

TCSB-20-200

TCSB-24-175

TCSB-24-200

TCSB-24-225

100

125

150

175

125

150

175

200

150

175

200

175

200

225

M-12

M-16

M-20

M-24

With hex key hole at top face for use on machine beds having tapped holes.

THREADLENGTH

30 X 40

30 X 50

30 X 65

30 X 80

40 X 50

40 X 65

40 X 80

40 X 100

50 X 60

50 X 70

50 X 80

60 X 70

60 X 80

60 X 90

CLAMPING STUD Hardend & Tempered, High Tensile Steel, Black Finish

For use with T-nuts.

MODELTHREAD

SIZETOTAL

LENGTHTHREADLENGTH

TCS-8-75

TCS-8-100

TCS-8-150

TCS-10-75

TCS-10-100

TCS-10-125

TCS-10-150

TCS-10-175

TCS-10-200

TCS-12-75

TCS-12-100

TCS-12-125

TCS-12-150

TCS-12-175

TCS-12-200

TCS-12-250

TCS-12-300

TCS-14-100

TCS-14-150

TCS-14-200

TCS-14-250

TCS-16-75

TCS-16-100

TCS-16-125

TCS-16-150

TCS-16-175

TCS-16-200

TCS-16-250

TCS-16-300

TCS-20-100

TCS-20-150

TCS-20-200

TCS-20-250

TCS-20-300

TCS-20-400

TCS-20-500

TCS-24-150

TCS-24-200

TCS-24-250

TCS-24-300

TCS-24-400

TCS-24-500

TCS-30-150

TCS-30-200

TCS-30-250

TCS-30-300

TCS-30-400

TCS-30-500

75

100

150

75

100

125

150

175

200

75

100

125

150

175

200

250

300

100

150

200

250

75

100

125

150

175

200

250

300

100

150

200

250

300

400

500

150

200

250

300

400

500

150

200

250

300

400

500

M-8

M-10

M-12

M-14

M-16

M-20

11 X 48

11 X 63

11 X 95

13 X 48

13 X 63

13 X 75

13 X 95

13 X 110

13 X 125

15 X 48

15 X 63

15 X 75

15 X 95

15 X 110

15 X 125

15 X 160

15 X 190

17 X 63

17 X 95

17 X 125

17 X 160

19 X 50

19 X 63

19 X 75

19 X 95

19 X 110

19 X 125

19 X 160

19 X 190

27 X 60

27 X 95

27 X 125

27 X 160

27 X 190

27 X 250

27 X 250

35 X 95

35 X 120

35 X 160

35 X 190

35 X 250

35 X 250

43 X 95

43 X 120

43 X 160

43 X 190

43 X 250

43 X 250

M-24

M-30

MODELTHREAD

SIZESUITABLE FOR T-SLOT SIZE

T- NUT Hardened & Tempered, Black Finish based on IS:2015

TTN-10-8

TTN-12-10*

TTN-14-10

TTN-14-12*

TTN-16-12

TTN-16-14*

TTN-18-12

TTN-18-16*

TTN-20-16

TTN-22-16

TTN-22-20*

TTN-24-20

TTN-28-24

TTN-36-24

TTN-36-30

10

12

14

14

16

16

18

18

20

22

22

24

28

36

36

15

18

22

22

25

25

28

28

32

35

35

40

44

54

54

M-8

M-10

M-10

M-12

M-12

M-14

M-12

M-16

M-16

M-16

M-20

M-20

M-24

M-24

M-30

S

SIZES

* marked models are not recommended for heavy duty use because of less wall

thickness outside the threading.

CLAMPS AND CLAMPING ELEMENTS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

Knurled outside diameter for easy gripping while quick insertion or removal.

C-WASHER Case Hardened, Ground Faces, Black Finish

MODELSUITABLE

FOR BOLT

TCW-10TCW-12TCW-14TCW-16TCW-20TCW-24TCW-30

M-10M-12 M-14M-16M-20M-24M-30

based on IS : 4291

THICKNESS

991111111114

OUTSIDE

DIA

4048636380

100100

PLAIN WASHER Case Hardened, Black Finish based on IS : 4291

TPW-8TPW-10TPW-12TPW-14TPW-16TPW-20TPW-24TPW-30

M-8M-10M-12M-14M-16M-20M-24M-30

MODELSUITABLE FOR

BOLT

445677911

THICKNESSOUTSIDE

DIA

2328354045486070

Consists of :T-Nuts : 6 Nos.Clamping Studs of six different lengths : 4 Nos. eachFlanged Nuts : 6 Nos.Extension Nuts : 4 Nos.Stepped Strap Clamps of three different lengths : 2 Nos. each Step blocks of three different sizes : 2 pairs (4 Nos.) each

CLAMPING KIT - 58 PIECE with step blocks & stepped strap clamps

TCK-58-1412TCK-58-1612L

TCK-58-1210TCK-58-1410TCK-58-1412L

M-12M-12

M-10M-10M-12

1312

99

12

TCK-58-1612TCK-58-1812TCK-58-1816TCK-58-2016TCK-58-2216

1416

121414

1618182022

M-12M-12M-16M-16M-16

1313181819

MODEL SUITABLE FOR T-SLOT SIZE N.W. Kgs.

Also Included T-Slot

Cleaner FFFREE

CLAMPING KIT - 34 PIECE with adjustable support plates & strap clamps

141618

M-12M-12M-12

TCK-34-1412TCK-34-1612TCK-34-1812

MODEL SUITABLE FOR T-SLOT SIZE THREAD SIZE

Consists of :

T-Nuts : 4 nos.Clamping Studs of four different lengths : 4 nos. eachFlanged Nuts : 4 nos.Extension Nuts : 2 nos.Strap Clamps of two different lengths : 2 nos. eachAdjustable Support Plates of two different sizes : 2 nos. each

CMM CLAMPING KIT - 62 PIECE with Aluminum / plastic clamping elements

Specially designed for 3D coordinate measuring machine and other inspection and gaging applications.

Model CMMCK-62 consists of :

28 nos. Aluminum M-8 studs of different lengths upto 200mm long.8 nos. M-8 Aluminum anged nuts (Hand Tightening Type).6 nos. Aluminum alloy strap clamps.8 nos. Aluminum screw jacks.4 nos. Aluminum top rest pads for screw jacks.8 nos. Plastic bottom rest pads for screw jacks and studs.

Adaptor available on request for CMM’s with M-10 or M-12 threaded beds.

New

EXTENSION NUT Hardened & Tempered, Black Finish

These nuts are used to couple the studs with studs or T- bolts in order to increase their length.

TEN-8TEN-10TEN-12TEN-14TEN-16TEN-20TEN-24TEN-30

M-8M-10M-12 M-14M-16M-20M-24M-30

2430364248607290

MODEL THREAD SIZE TOTAL LENGTH

FLANGED NUT Forged, Hardened & Tempered, Black Finish

These nuts have anged face for larger face contact with the surface to be tightened on.

TFN-12TFN-16TFN-20TFN-24

18243036

M-12M-16M-20M-24

MODEL THREAD SIZE TOTAL

LENGTH

Also Included T-Slot

Cleaner FFFREE

Visit for online details of above products or write to us for a print copy www.toolfastclamps.com

CLAMPS AND CLAMPING ELEMENTS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

7

THREAD SIZE

T-Slot size mentioned in these pages is size ‘A’ of the T-Slot as shown here.A

Page 8: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

WEDGE CLAMPS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

WEDGE CLAMP - TWC SERIES Serrated Hardened Jaws

TWC-8

TWC-12

TWC-16

MODEL

M8

M12

M16

2500 Kgs

5000 Kgs

10000 Kgs

CLAMPING

FORCE

CLAMPING

SCREW

If your workpiece is suitable for clamping with 'TOOLFAST' Wedge clamps, our team can design and manufacture a multiple clamping xture for you as the one shown in the picture.

Please send in your enquiries with workpiece / machine table specications to us if you feel that 'TOOLFAST' wedge clamps are suitable for your workpiece or simply send your workpiece/ machine details to us and let us decide it.

MULTIPLE WORKPIECE CLAMPING FIXTURES WITH TWC SERIES WEDGE CLAMPS DESIGNED & MANUFACTURED BY TOOLFAST

FixtureBase Plate

Wedge Clamp

WorkpiecesUnusual Shape

Workpiece

Machinable Wedge Clamp

WEDGE CLAMP - RIGID BODY, HARDENED TOOL STEEL, DOWNWARD FORCE

‘TOOLFAST’ manufactures all models of wedge clamps with new patented design now in India.

¦ Patented design with bottom spring ensures downward Clamping force

¦ Hidden spring eliminates clogging of chips in spring coil

These have plain hardened jaws with added two tapped holes for attaching additional jaw inserts if need be.

WEDGE CLAMP - TWC-P SERIES Plain Hardened Jaws with Tapped Holes

TWC-8 P

TWC-12 P

TWC-16 P

M8

M12

M16

2500 Kgs

5000 Kgs

10000 Kgs

CLAMPING

FORCE

CLAMPING

SCREWMODEL

These have extra material on jaws (soft) to machine as per the workpiece shape enabling xturing of uneven or unusual shape work pieces.

WEDGE CLAMP - TWC-M SERIES Machinable Jaws

TWC-8 M

TWC-12 M

TWC-16 M

M8

M12

M16

2500 Kgs

5000 Kgs

10000 Kgs

CLAMPING

FORCE

CLAMPING

SCREW

• Model VTWC-16-60-350 available as standard having overall length 350mm capable of jaw opening 91mm in case of two workpieces.

• Above vice can be supplied in custom built lengths to suit different sizes of workpieces. Send your enquiries to us if you feel that 60mm jaw width vice can hold your workpiece. Additional xed jaws and TWC series clamps can be included in the vice if more than two workpieces to be clamped.

• For uneven or unusual shape workpieces, TWC-M and TWC-P series wedge clamps can also be used in above vice.

TOOLFAST offers a 60mm jaw width vice which is capable of clamping multiple workpieces. All parts such as TWC wedge clamp, xed jaws and the main body are modular and interchangeable.

MULTIPLE CLAMPING VICE WITH TWC-16 WEDGE CLAMPS

Wedge Clamp TWC-16

Workpieces

Adjustable PositionFixed Jaw

4 Nos. Mounting Clamps included

MODEL

New

2D / 3D CAD les available on request

98

PITBULL CLAMPS

The Pitbull Clamp is a revolutionary new xture clamp with positive down force and a low gripping prole. High vertical and horizontal clamping forces are generated, considering the size of the Pitbull Clamps. It uses a standard cap screw and an oil resistant O-ring. The Pitbull Clamp is available in 5 sizes and several styles, a tool steel knife edge for aggressive stock removal, a tool steel blunt edge for general purpose and a brass version to help prevent marring the workpiece.

Available in different models having clamping screw sizes from M-4 to M-12.

Fixture example of clamping by Pitbull Clamp

Workpiece

Pitbull Clamp

Clamping Screw

MACHINABLE FIXTURE CLAMPS

Also available 'Machinable Fixture Clamps' where the clamping portion has to be machined by the user as per the prole of the work piece to hold round or unusual shape parts.

MACHINABLE UNIFORCE CLAMPS

Also available 'Machinable Uniforce Clamps' with extra material on the clamping jaws so it can be machined by the user as per the prole of the work piece enabling to xture unusual applications easily.

The Cam Action Fixture Clamp is made up of two simple components : a hardened steel socket cap screw with an offset head and a hexagonal washer. This clamp is used for low prole side clamping.

q Low prole makes computer programming easier.q Cam action provides fast, strong clamping.q Small size allows more parts per load.q Simple design keeps cost low.

FIXTURE CLAMPS - ECCENTRIC TYPE

FIXTURE CLAMPS

Ask us for details of products before designing your xture or visit www.miteebite.com

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. MADE IN U.S.A.

UNIFORCE CLAMPS - WEDGE TYPE

The compact, economical Uniforce Clamp enables you to xture more parts on the machine table. The specially designed steel wedge spreads the clamping force uniformly on both sides of the channel Jaw. Ideal for clamping at or round work pieces in multiple set ups.

Cam action side clamping

Available in clamping screw sizes M-2 to M-16.

Available in screw sizes M- 4 to M-16

This adjustable low prole, cam action clamp provides clamping of different size work pieces merely by rotating the clamp to one of its other edges. The clamps are 10mm high and use M12 cam screw. Each of the six clamping surfaces is a different distance from the centerline by 1 mm. Therefore, one Series-9 Clamp can hold parts that vary up to 9.4mm simply by rotating the clamp to a different clamping surface.

q Serrated edges.q Heat treated and plated.

SERIES-9 CLAMPS

Each of the six clamping surfaces is number punched for identication and is at a different

distance from the centerline by 1 mm.

ID XPANSION CLAMP

TMThe ID Xpansion clamp is the ideal way to hold parts on an inside diameter for multiple machining on a vertical machining center or a horizontal machining center.These machinable clamps are produced in 8 sizes and can hold internal diameters from 8mm to over 75mm. The clamps use a heat treated tapered screw for expansion.The larger diameter of the clamp is held to a close tolerance for precision locating in a machined pocket on work cubes and xture plates.The customer machines the soft steel clamp to match the bore of the part ensuring proper t. Often times the clamps can be remachined for different size jobs.

Clamping by ID Expansion Clamp

on a multiple clamping xture

Available in different sizes to hold internal diameters from 8 mm to 103 mm.

COMPACT TOE CLAMPS

KNIFE EDGE CLAMPS

Knife Edge Clamps can be used instead of the above Fixture clamps for clamping rough cut stock, castings and any material that requires a hardened clamping element.

Available in M-10, M-12 and M-16 screw sizes.

This cam action clamp provides positive down force while using very little space on a xture. Workspieces can be clamped in series by using the back surface of a clamp to locate the next workpiece. The hardened steel clamping element has both a smooth surface for machined workpieces and a serrated clamping surface for rougher work. The height of the clamp can be adjusted by milling the slot deeper in the xture plate.

Page 9: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

WEDGE CLAMPS

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

WEDGE CLAMP - TWC SERIES Serrated Hardened Jaws

TWC-8

TWC-12

TWC-16

MODEL

M8

M12

M16

2500 Kgs

5000 Kgs

10000 Kgs

CLAMPING

FORCE

CLAMPING

SCREW

If your workpiece is suitable for clamping with 'TOOLFAST' Wedge clamps, our team can design and manufacture a multiple clamping xture for you as the one shown in the picture.

Please send in your enquiries with workpiece / machine table specications to us if you feel that 'TOOLFAST' wedge clamps are suitable for your workpiece or simply send your workpiece/ machine details to us and let us decide it.

MULTIPLE WORKPIECE CLAMPING FIXTURES WITH TWC SERIES WEDGE CLAMPS DESIGNED & MANUFACTURED BY TOOLFAST

FixtureBase Plate

Wedge Clamp

WorkpiecesUnusual Shape

Workpiece

Machinable Wedge Clamp

WEDGE CLAMP - RIGID BODY, HARDENED TOOL STEEL, DOWNWARD FORCE

‘TOOLFAST’ manufactures all models of wedge clamps with new patented design now in India.

¦ Patented design with bottom spring ensures downward Clamping force

¦ Hidden spring eliminates clogging of chips in spring coil

These have plain hardened jaws with added two tapped holes for attaching additional jaw inserts if need be.

WEDGE CLAMP - TWC-P SERIES Plain Hardened Jaws with Tapped Holes

TWC-8 P

TWC-12 P

TWC-16 P

M8

M12

M16

2500 Kgs

5000 Kgs

10000 Kgs

CLAMPING

FORCE

CLAMPING

SCREWMODEL

These have extra material on jaws (soft) to machine as per the workpiece shape enabling xturing of uneven or unusual shape work pieces.

WEDGE CLAMP - TWC-M SERIES Machinable Jaws

TWC-8 M

TWC-12 M

TWC-16 M

M8

M12

M16

2500 Kgs

5000 Kgs

10000 Kgs

CLAMPING

FORCE

CLAMPING

SCREW

• Model VTWC-16-60-350 available as standard having overall length 350mm capable of jaw opening 91mm in case of two workpieces.

• Above vice can be supplied in custom built lengths to suit different sizes of workpieces. Send your enquiries to us if you feel that 60mm jaw width vice can hold your workpiece. Additional xed jaws and TWC series clamps can be included in the vice if more than two workpieces to be clamped.

• For uneven or unusual shape workpieces, TWC-M and TWC-P series wedge clamps can also be used in above vice.

TOOLFAST offers a 60mm jaw width vice which is capable of clamping multiple workpieces. All parts such as TWC wedge clamp, xed jaws and the main body are modular and interchangeable.

MULTIPLE CLAMPING VICE WITH TWC-16 WEDGE CLAMPS

Wedge Clamp TWC-16

Workpieces

Adjustable PositionFixed Jaw

4 Nos. Mounting Clamps included

MODEL

New

2D / 3D CAD les available on request

98

PITBULL CLAMPS

The Pitbull Clamp is a revolutionary new xture clamp with positive down force and a low gripping prole. High vertical and horizontal clamping forces are generated, considering the size of the Pitbull Clamps. It uses a standard cap screw and an oil resistant O-ring. The Pitbull Clamp is available in 5 sizes and several styles, a tool steel knife edge for aggressive stock removal, a tool steel blunt edge for general purpose and a brass version to help prevent marring the workpiece.

Available in different models having clamping screw sizes from M-4 to M-12.

Fixture example of clamping by Pitbull Clamp

Workpiece

Pitbull Clamp

Clamping Screw

MACHINABLE FIXTURE CLAMPS

Also available 'Machinable Fixture Clamps' where the clamping portion has to be machined by the user as per the prole of the work piece to hold round or unusual shape parts.

MACHINABLE UNIFORCE CLAMPS

Also available 'Machinable Uniforce Clamps' with extra material on the clamping jaws so it can be machined by the user as per the prole of the work piece enabling to xture unusual applications easily.

The Cam Action Fixture Clamp is made up of two simple components : a hardened steel socket cap screw with an offset head and a hexagonal washer. This clamp is used for low prole side clamping.

q Low prole makes computer programming easier.q Cam action provides fast, strong clamping.q Small size allows more parts per load.q Simple design keeps cost low.

FIXTURE CLAMPS - ECCENTRIC TYPE

FIXTURE CLAMPS

Ask us for details of products before designing your xture or visit www.miteebite.com

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. MADE IN U.S.A.

UNIFORCE CLAMPS - WEDGE TYPE

The compact, economical Uniforce Clamp enables you to xture more parts on the machine table. The specially designed steel wedge spreads the clamping force uniformly on both sides of the channel Jaw. Ideal for clamping at or round work pieces in multiple set ups.

Cam action side clamping

Available in clamping screw sizes M-2 to M-16.

Available in screw sizes M- 4 to M-16

This adjustable low prole, cam action clamp provides clamping of different size work pieces merely by rotating the clamp to one of its other edges. The clamps are 10mm high and use M12 cam screw. Each of the six clamping surfaces is a different distance from the centerline by 1 mm. Therefore, one Series-9 Clamp can hold parts that vary up to 9.4mm simply by rotating the clamp to a different clamping surface.

q Serrated edges.q Heat treated and plated.

SERIES-9 CLAMPS

Each of the six clamping surfaces is number punched for identication and is at a different

distance from the centerline by 1 mm.

ID XPANSION CLAMP

TMThe ID Xpansion clamp is the ideal way to hold parts on an inside diameter for multiple machining on a vertical machining center or a horizontal machining center.These machinable clamps are produced in 8 sizes and can hold internal diameters from 8mm to over 75mm. The clamps use a heat treated tapered screw for expansion.The larger diameter of the clamp is held to a close tolerance for precision locating in a machined pocket on work cubes and xture plates.The customer machines the soft steel clamp to match the bore of the part ensuring proper t. Often times the clamps can be remachined for different size jobs.

Clamping by ID Expansion Clamp

on a multiple clamping xture

Available in different sizes to hold internal diameters from 8 mm to 103 mm.

COMPACT TOE CLAMPS

KNIFE EDGE CLAMPS

Knife Edge Clamps can be used instead of the above Fixture clamps for clamping rough cut stock, castings and any material that requires a hardened clamping element.

Available in M-10, M-12 and M-16 screw sizes.

This cam action clamp provides positive down force while using very little space on a xture. Workspieces can be clamped in series by using the back surface of a clamp to locate the next workpiece. The hardened steel clamping element has both a smooth surface for machined workpieces and a serrated clamping surface for rougher work. The height of the clamp can be adjusted by milling the slot deeper in the xture plate.

Page 10: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

VACMAGIC - PALLET CHANGER & VACUUM CHUCK

USES STANDARD SHOP AIR, NO VACUUM PUMP REQUIRED

Low prole base unit quickly mounts to 2machine table. Operates with 5 Kg/cm

standard shop air.

Vacuum pallet with rubber cord positioned on base unit for thin

workpiece ready to be used as a vacuum chuck.

Example of standard pallet machined into a xture plate positioned on base

unit for increased production.

Vise mounted on standard pallet positioned on base unit for quick change from production to prototype.

VACUUM CHUCK APPLICATION PALLET CHANGER APPLICATION

Ask us for details of products before designing your xture or visit www.miteebite.com

T-SLOT CLAMP KITS (SIDE CLAMPING)

VISE PALLETS

The original MITEE-BITE T-Slot Clamp combines the unique cam action brass clamping element with a T-nut.

q L ocks in machine T-slot for low prole clamping q Makes fast set-ups possible right on the machine tableq Brass hex follows contour of unusual shaped parts q Packed in complete kits

PART NO. CAM SCREWT-SLOT SIZE

50644 10mm M6

50646 12mm M8

50648 14mm M10

50650 16mm M12

50652 18mm M12

TM TMTALONGRIP AND VERSAGRIP VISE JAWS

Reduce set up times and increase efciency on small production jobs. The pallets can be reused for repeat jobs.

q N ow you can run xture jobs without removing your vises.

q T hese Vise Pallets are designed to t in all 150mm vises and measure approximately 152 x 203mm and 152 x 254mm. They are available blank and with 10mm T-slots.

q T he Blank Pallets are ideal for multiple small parts using one of several MITEE-BITE low prole edge clamps.

q T he T-Slot Pallets can be used with our T-Slot Clamps or the versatile 10mm Riser Kit (#51088) for non-dedicated applications.

q T he Vise Pallets are qualied in 2 places so they can rest on parallels or on the top of the jaws.

The Mitee-Bite Kit Contains: 4 Mitee-Bite T-Nuts 6 Mitee-Bite Fixture Clamps 2 Hex Keys

MITEE-BITE Products introduces a new and innovative product that will increase the functionality of your standard 4 and 6 inch

TM(100mm and 150mm) vises . TalonGrip is a simple bolt on system that will allow you to perform aggressive machining operations while clamping on as little as 1.5mm. Ideal for small lot sizes, difcult applications or proto-type work when building a xture would not be benecial.

VersaGripTM, as the name implies, offers the versatility of clamping standard vise work as well as providing a solution for difcult applications that would normally require xturing or machining soft-jaws. By simply replacing your current jaws with the VersaGripTM system you can securely hold odd shaped parts while machining at speeds and feeds you never thought possible.

TALONGRIP VISE JAWS VERSAGRIP VISE JAWS

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. MADE IN U.S.A.

CLAMPS AND PALLETS

PRECISION SINE VICE

‘TOOLFAST’ Precision Sine Vice is used to obtain precise angles by means of gauge blocks. Apart from its use on milling and grinding machine, this Sine Vice can also be used as a reference for inspection.

A ll Hardened & Tempered to 52 - 56 HRC.All side Parallelism & Squareness within ± 0.005mm.

Centre distance of rollers within ± 0.005mm.Inspection certicate is furnished.

Chart for setting sine angles with the help of gauge blocks is provided.

PRECISION STEEL PARALLELS

‘TOOLFAST’ Steel Parallels are used as precision packing supports under jobs or xtures. Made from tool steel, hardened, tempered & precision ground in matched pairs. Matched pairs are marked with identical serial numbers. All sides are chamfered. Overall sizes are nominal.

Hardened & Tempered 52 - 56 HRC.Parallelism within 0.005mm upto 200mm length.Inspection certicate is furnished.

MODEL

EF-S1

EF-D1

EFR-10

EFR-104

SHANK DIA

10

10

10

10

TIP DIA

10

5 &10

10

4 & 10

TYPE

Edge Finder-single end

Edge Finder-double end

Edge Finder-disc type

Disc Type - double end

‘TOOLFAST’ Grinding Vice - screw type is a precision machine vice. Body & jaw made of tool steel, hardened, tempered & precision ground.

Hardened & Tempered to 52 - 56 HRC.

All sides Parallelism & Squareness within ± 0.005mm.

Inspection certicate is furnished.

GRINDING VICE - SCREW TYPE

MILLING & GRINDING ACCESSORIES

MODEL SIZE

10 x 20 x 150

15 x 35 x 150

20 x 45 x 200

25 x 55 x 250

30 x 60 x 300

45 x 75 x 300

TSP-20

TSP-35

TSP-45

TSP-55

TSP-60

TSP-75

MODEL JAW DEPTH MAX. JAW OPENINGJAW WIDTH

637388

100125150

323540455050

GV-65GV-75GV-90GV-100GV-125GV-150

85100125125158175

OVERALL LENGTH OVERALL HEIGHT

190210250260300315

65748895110110

MODEL JAW DEPTHJAW WIDTH

PSV-2

PSV-3

PSV-4

50

73

100

25

35

45

65

100

125

MAX. JAW OPENING

OVERALLLENGTH

OVERALLHEIGHT

140

190

245

80

104

134

EF-D1 EF-S1 EFR-10 EFR-104

EDGE FINDER

TOOLFAST’ Edge Finder is used for fast and accurate location of starting point of work pieces with respect to the machine spindle on milling or jig boring machine tables.

Application: Edge nder is used for location of edges, shoulders, grooves etc. of work pieces kept on machine table with respect to the machine spindle. Shank of the Edge Finder is held in the collet or chuck and work table is traversed to cause the rotating tip of the edge nder make contact with the edge of the work piece to be located. Once the rotating tip comes in contact with the work piece, work table is further traversed so that the rotating tip shifts to a concentric position with respect to the shank. Now any movement to "off centre" will cause a distinct 'wobble'. At this point, the distance from the work edge to the centre of machine spindle is equal to half the diameter of the tip of the edge nder. Available in single & double ended tip. In double ended tip, Edge Finder can be held from both ends and both the tips of two different sizes can be used for edge nding.

Shank and tip of the edge nder are coupled together with the help of an internal spring for independent rotation of both. It is hardened and accurately ground all over to ensure repeatability of work location within 0.01 mm.

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

1110

qqq

q

q

q

q

qqq

Page 11: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

VACMAGIC - PALLET CHANGER & VACUUM CHUCK

USES STANDARD SHOP AIR, NO VACUUM PUMP REQUIRED

Low prole base unit quickly mounts to 2machine table. Operates with 5 Kg/cm

standard shop air.

Vacuum pallet with rubber cord positioned on base unit for thin

workpiece ready to be used as a vacuum chuck.

Example of standard pallet machined into a xture plate positioned on base

unit for increased production.

Vise mounted on standard pallet positioned on base unit for quick change from production to prototype.

VACUUM CHUCK APPLICATION PALLET CHANGER APPLICATION

Ask us for details of products before designing your xture or visit www.miteebite.com

T-SLOT CLAMP KITS (SIDE CLAMPING)

VISE PALLETS

The original MITEE-BITE T-Slot Clamp combines the unique cam action brass clamping element with a T-nut.

q L ocks in machine T-slot for low prole clamping q Makes fast set-ups possible right on the machine tableq Brass hex follows contour of unusual shaped parts q Packed in complete kits

PART NO. CAM SCREWT-SLOT SIZE

50644 10mm M6

50646 12mm M8

50648 14mm M10

50650 16mm M12

50652 18mm M12

TM TMTALONGRIP AND VERSAGRIP VISE JAWS

Reduce set up times and increase efciency on small production jobs. The pallets can be reused for repeat jobs.

q N ow you can run xture jobs without removing your vises.

q T hese Vise Pallets are designed to t in all 150mm vises and measure approximately 152 x 203mm and 152 x 254mm. They are available blank and with 10mm T-slots.

q T he Blank Pallets are ideal for multiple small parts using one of several MITEE-BITE low prole edge clamps.

q T he T-Slot Pallets can be used with our T-Slot Clamps or the versatile 10mm Riser Kit (#51088) for non-dedicated applications.

q T he Vise Pallets are qualied in 2 places so they can rest on parallels or on the top of the jaws.

The Mitee-Bite Kit Contains: 4 Mitee-Bite T-Nuts 6 Mitee-Bite Fixture Clamps 2 Hex Keys

MITEE-BITE Products introduces a new and innovative product that will increase the functionality of your standard 4 and 6 inch

TM(100mm and 150mm) vises . TalonGrip is a simple bolt on system that will allow you to perform aggressive machining operations while clamping on as little as 1.5mm. Ideal for small lot sizes, difcult applications or proto-type work when building a xture would not be benecial.

VersaGripTM, as the name implies, offers the versatility of clamping standard vise work as well as providing a solution for difcult applications that would normally require xturing or machining soft-jaws. By simply replacing your current jaws with the VersaGripTM system you can securely hold odd shaped parts while machining at speeds and feeds you never thought possible.

TALONGRIP VISE JAWS VERSAGRIP VISE JAWS

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. MADE IN U.S.A.

CLAMPS AND PALLETS

PRECISION SINE VICE

‘TOOLFAST’ Precision Sine Vice is used to obtain precise angles by means of gauge blocks. Apart from its use on milling and grinding machine, this Sine Vice can also be used as a reference for inspection.

A ll Hardened & Tempered to 52 - 56 HRC.All side Parallelism & Squareness within ± 0.005mm.

Centre distance of rollers within ± 0.005mm.Inspection certicate is furnished.

Chart for setting sine angles with the help of gauge blocks is provided.

PRECISION STEEL PARALLELS

‘TOOLFAST’ Steel Parallels are used as precision packing supports under jobs or xtures. Made from tool steel, hardened, tempered & precision ground in matched pairs. Matched pairs are marked with identical serial numbers. All sides are chamfered. Overall sizes are nominal.

Hardened & Tempered 52 - 56 HRC.Parallelism within 0.005mm upto 200mm length.Inspection certicate is furnished.

MODEL

EF-S1

EF-D1

EFR-10

EFR-104

SHANK DIA

10

10

10

10

TIP DIA

10

5 &10

10

4 & 10

TYPE

Edge Finder-single end

Edge Finder-double end

Edge Finder-disc type

Disc Type - double end

‘TOOLFAST’ Grinding Vice - screw type is a precision machine vice. Body & jaw made of tool steel, hardened, tempered & precision ground.

Hardened & Tempered to 52 - 56 HRC.

All sides Parallelism & Squareness within ± 0.005mm.

Inspection certicate is furnished.

GRINDING VICE - SCREW TYPE

MILLING & GRINDING ACCESSORIES

MODEL SIZE

10 x 20 x 150

15 x 35 x 150

20 x 45 x 200

25 x 55 x 250

30 x 60 x 300

45 x 75 x 300

TSP-20

TSP-35

TSP-45

TSP-55

TSP-60

TSP-75

MODEL JAW DEPTH MAX. JAW OPENINGJAW WIDTH

637388

100125150

323540455050

GV-65GV-75GV-90GV-100GV-125GV-150

85100125125158175

OVERALL LENGTH OVERALL HEIGHT

190210250260300315

65748895110110

MODEL JAW DEPTHJAW WIDTH

PSV-2

PSV-3

PSV-4

50

73

100

25

35

45

65

100

125

MAX. JAW OPENING

OVERALLLENGTH

OVERALLHEIGHT

140

190

245

80

104

134

EF-D1 EF-S1 EFR-10 EFR-104

EDGE FINDER

TOOLFAST’ Edge Finder is used for fast and accurate location of starting point of work pieces with respect to the machine spindle on milling or jig boring machine tables.

Application: Edge nder is used for location of edges, shoulders, grooves etc. of work pieces kept on machine table with respect to the machine spindle. Shank of the Edge Finder is held in the collet or chuck and work table is traversed to cause the rotating tip of the edge nder make contact with the edge of the work piece to be located. Once the rotating tip comes in contact with the work piece, work table is further traversed so that the rotating tip shifts to a concentric position with respect to the shank. Now any movement to "off centre" will cause a distinct 'wobble'. At this point, the distance from the work edge to the centre of machine spindle is equal to half the diameter of the tip of the edge nder. Available in single & double ended tip. In double ended tip, Edge Finder can be held from both ends and both the tips of two different sizes can be used for edge nding.

Shank and tip of the edge nder are coupled together with the help of an internal spring for independent rotation of both. It is hardened and accurately ground all over to ensure repeatability of work location within 0.01 mm.

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

1110

qqq

q

q

q

q

qqq

Page 12: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

STEEL V-BLOCK

‘TOOLFAST’ Steel V-Blocks are made of tool steel, hardened, tempered & precision ground on all sides. These are supplied in matched pairs having both sides ‘V’ with one clamp.

Unbreakable Steel Clamp. All Hardened & Tempered 52 - 56 HRC.Parallelism & Squareness of all faces & 'V' within ± 0.005mm.

q Inspection certicate is furnished.

PRECISION COMPOUND SINE VICE - SCREW TYPE

C. I. ANGLE PLATE - SLOTTED

Sizes APS-110 to APS-200 are in open ends type as shown in picture.Sizes APS-225 to APS-300 are in webbed ends type .

‘TOOLFAST’ C. I. Angle Plate-Slotted is made out of high quality seasoned casting having precision ground outside faces & ends. Machined slots for clamping on both faces.

Accuracy in parallelism & squareness within ± 0.01mm per 200 mm length. Inspection certicate is furnished.

MAGNETIC V-BLOCK

‘TOOLFAST’ Magnetic V-Blocks are precision ground V-Blocks with high power magnets. Accurately tted

magnet ensures easy movement of knob. Available in single as well as matched pairs. These V-blocks have main holding 'V' and bottom face tted with hardened steel plates having hardness

52-56 HRC.

q P arallelism & Squareness of all faces & 'V' within ± 0 .005mm.q M ost suitable for inspection and tool room applications.q Inspection certicate is furnished.

Grinding Accessories

LENGTH

SVB-50SVB-80SVB-100SVB-125SVB-150

5080

100125150

3760759598

3760759598

WIDTH

MODEL LENGTH HEIGHT

MVB-4-HMVB-6-H

100150

9595

7575

WIDTH

MODEL SIZE

APS-110APS-150APS-175APS-200APS-225APS-250APS-300

110 x 85 x 75150 x 125 x 110175 x 135 x 110200 x 150 x 125225 x 175 x 150250 x 200 x 150300 x 225 x 200

‘TOOLFAST’ Precision compound Sine Vice has compound sine angle setting on two sine plates. Both the tiltings are controlled by ne screws.

All Hardened & Tempered to 52 - 56 HRC.All side Parallelism & Squareness within ± 0.005mm.Centre distance of rollers within ± 0.005mm.Inspection certicate is furnished.

Charts for setting both sine angles with the help of gauge blocks is provided.

MODEL JAW DEPTHJAW WIDTH

CSGV-3

MAX. JAW OPENING

OVERALLLENGTH

OVERALLHEIGHT

HOLDING CAPACITY

Ø MAX

3560759095

75 30 76 160 124

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

New

Milling & MC Vices

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

1312

MODEL HEIGHT

qqq

qqqq

qq

OPTIONAL ACCESSORIES

OPTIONAL JAWS FOR MMV-6HXL

SWIVAL BASE:Available separately for all above three sizes of vice.

SERRATED JAW PLATE

Dimensions same as standard plain Jaw but having serrations for extra grip.

MACHINABLE JAW PLATE

• Extra thick (40mm) for carving part shapes into jaw plate.

• Reversible top to bottom and front to back, (counter bore both sides).

• Available in Aluminium and steel both.

V-JAW PLATE

* Required torque can be achieved by tightening handle included with vice. Applying extra torque by using extension pipe or by hammering damages the vice parts and warranty expires.

JAWWIDTH

JAWDEPTH

N.W.WITHOUTSWIVAL

BASE Kgs.

CLAMPING FORCE

Max.

TIGHTENINGTORQUE Nm Max.*

150

580

650

2000 Kgs.

3500 Kgs.

4000 Kgs.

Page 13: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

STEEL V-BLOCK

‘TOOLFAST’ Steel V-Blocks are made of tool steel, hardened, tempered & precision ground on all sides. These are supplied in matched pairs having both sides ‘V’ with one clamp.

Unbreakable Steel Clamp. All Hardened & Tempered 52 - 56 HRC.Parallelism & Squareness of all faces & 'V' within ± 0.005mm.

q Inspection certicate is furnished.

PRECISION COMPOUND SINE VICE - SCREW TYPE

C. I. ANGLE PLATE - SLOTTED

Sizes APS-110 to APS-200 are in open ends type as shown in picture.Sizes APS-225 to APS-300 are in webbed ends type .

‘TOOLFAST’ C. I. Angle Plate-Slotted is made out of high quality seasoned casting having precision ground outside faces & ends. Machined slots for clamping on both faces.

Accuracy in parallelism & squareness within ± 0.01mm per 200 mm length. Inspection certicate is furnished.

MAGNETIC V-BLOCK

‘TOOLFAST’ Magnetic V-Blocks are precision ground V-Blocks with high power magnets. Accurately tted

magnet ensures easy movement of knob. Available in single as well as matched pairs. These V-blocks have main holding 'V' and bottom face tted with hardened steel plates having hardness

52-56 HRC.

q P arallelism & Squareness of all faces & 'V' within ± 0 .005mm.q M ost suitable for inspection and tool room applications.q Inspection certicate is furnished.

Grinding Accessories

LENGTH

SVB-50SVB-80SVB-100SVB-125SVB-150

5080100125150

3760759598

3760759598

WIDTH

MODEL LENGTH HEIGHT

MVB-4-HMVB-6-H

100150

9595

7575

WIDTH

MODEL SIZE

APS-110APS-150APS-175APS-200APS-225APS-250APS-300

110 x 85 x 75150 x 125 x 110175 x 135 x 110200 x 150 x 125225 x 175 x 150250 x 200 x 150300 x 225 x 200

‘TOOLFAST’ Precision compound Sine Vice has compound sine angle setting on two sine plates. Both the tiltings are controlled by ne screws.

All Hardened & Tempered to 52 - 56 HRC.All side Parallelism & Squareness within ± 0.005mm.Centre distance of rollers within ± 0.005mm.Inspection certicate is furnished.

Charts for setting both sine angles with the help of gauge blocks is provided.

MODEL JAW DEPTHJAW WIDTH

CSGV-3

MAX. JAW OPENING

OVERALLLENGTH

OVERALLHEIGHT

HOLDING CAPACITY

Ø MAX

3560759095

75 30 76 160 124

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

New

Milling & MC Vices

MANUFACTURED BY ABBOTT TOOLFAST PVT. LTD.

1312

MODEL HEIGHT

qqq

qqqq

qq

OPTIONAL ACCESSORIES

OPTIONAL JAWS FOR MMV-6HXL

SWIVAL BASE:Available separately for all above three sizes of vice.

SERRATED JAW PLATE

Dimensions same as standard plain Jaw but having serrations for extra grip.

MACHINABLE JAW PLATE

• Extra thick (40mm) for carving part shapes into jaw plate.

• Reversible top to bottom and front to back, (counter bore both sides).

• Available in Aluminium and steel both.

V-JAW PLATE

* Required torque can be achieved by tightening handle included with vice. Applying extra torque by using extension pipe or by hammering damages the vice parts and warranty expires.

JAWWIDTH

JAWDEPTH

N.W.WITHOUTSWIVAL

BASE Kgs.

CLAMPING FORCE

Max.

TIGHTENINGTORQUE Nm Max.*

150

580

650

2000 Kgs.

3500 Kgs.

4000 Kgs.

Page 14: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

WORLD RENOWNED MODULAR VISES

SOLD & SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.Made in Italy

®

PRECISION MODULAR VISE 'STANDARD SERIES' WITH GUIDED MOVABLE JAW (ART. 1)

q High precision and gang operation

q Pull down easy to change jaws

q Unlimited longevity

q Space saving design

q No "wear" construction

q Unlimited clamping range

q All steel construction hardened and ground HRc60

JAW WIDTH

JAW DEPTH

MAX. JAW OPENING

ART. 11

VISE SIZE

100

30

100

2

125

40

150

3

150

50

4

175

60

5

200

65

6

300

80

200 300 200 300 400 500 200 300 400 500 600 200 300 400 500 600 700 800

A

B

C

D

E

F

G

H

I

J

K

L

M

N

VISE Art. 1

List of Optional Accessories

A Swivel base - ART. 105B Blocking support with hydraulic cylinder - A R T. 271C Hydraulic hand screw blocking device - ART. 257D Intermediate movable jaw with double step - A R T. 212E Floating movable jaw for round parts - ART. 210F Fixed stack type prismatic jaw - ART. 150G Fixed and movable stack-type jaws for round parts - A R T.131H Square stack-type jaws - ART. 138I Movable jaw with 2 oating segment s - ART. 190J Floating movable jaw - hydraulic control - A R T. 188K Step-prismatic guided movable jaw - A R T. 217L Guided movable jaw - straight plate - ART. 146M/N Extension for xed and movable jaw with screws - ART. 132/133

HYDRAULIC CLAMPING OPTION

OptionalAccessories

VISE WITH STANDARD ACCESSORIES

Mention vise size (jaw width) and max. jaw opening for ordering

MODULAR VISES "XL" SERIES

Art. 20Available in different models having jaw width up to 300 mm and jaw opening up to 1100 mm.

Art. 30Available in different models having jaw width up to 300 mm and jaw opening for two work pieces up to 460 mm each.

The hand hydraulic clamping group Art. 257 is an optional manual power multiplier alternative to the mechanical clamping of above vices. This device allows to reach the same clamping power reachable with the mechanical screw through a minimum effort. The hand hydraulic screw of Art. 257 is manually operated by the wrench included. All above Art. 1 vices can be purchased with Art. 257 tted.

Art. 257

1000 Kgf

Available in jaw width 49 mm, 74 mm and 99 mm having jaw opening up to 832 mm for single piece and up to 134 mm each for four work pieces held simultaneously.

1

DMax opening according to pieces to be clamped

300

400

500

600

700

B C E1 2 3 4 5 6 7 8 9

50

50

50

50

50

50

50

50

50

50

32/25

32/25

32/25

32/25

32/25

208

308

408

508

608

75

125

175

225

275

30

64

96

129

161

8

33

58

83

108

\

15

35

55

75

\

3

19

36

52

\

\

8

22

36

\

\

\

12

24

\

\

\

5

16

2

400

500

600

700

800

75

75

75

75

75

75

75

75

75

75

40

40

40

40

40

275

375

475

575

675

100

150

200

250

300

41

75

108

141

175

12

37

62

87

112

\

15

35

55

75

\

\

16

33

50

\

\

3

17

32

\

\

\

6

18

\

\

\

\

8

SIZE

3

700

800

900

1000

100

100

100

100

60

60

60

60

532

632

732

832

217

267

317

367

112

145

178

211

59

84

109

134

28

48

68

88

7

23

39

55

\

6

20

34

\

\

5

18

\

\

\

5

100

100

100

100

Made in Italy

®

HYDROPNEUMATIC POWER UNIT

Gerardi hydropneumatic power unit for hydraulic clamping devices and its bi-products is designed to meet all needs regarding the powering of hydraulic cylinders where low ow rates and high pressures are required. It is driven by air at its inlet to produce hydraulic pressure at its outlet. The special design shape of the power unit is such that a high performance system can be implemented taking up very little space. Thanks to the special design principles, the pump section adopted allows the hydropneumatic power unit to be installed in very hostile environments, such as the work area of machine tools, etc. The unique modular hydraulic ow control system allows controlling up to 6 separate users from just one power unit.

SPECIFICATION

MAX. PERMISSIBLE INLET AIR PRESSURE: 7 bar

RECOMMENDED INLET AIR PRESSURE: 5,5 bar

OIL DELIVERIES: 1.2-1.4-2.2-2.7-4.3 Liters/min

MAX. OIL OUTLET PRESSURE AT 5 BAR AIR INLET PRESSURE: 400 bar

MAX. NO. OF USERS RECOMMENDED: 6

PNEUMO - HYDRAULIC BLOCKING DEVICE

"MULTIFLEX" VICES ART. 600

Art. 393 - Power unit with Manual control, Art. 394 - Power unit with Pneumatic control, Art. 395 - Power unit with Electrical control

A bove power unit can be used to operate Mechanical Modular Vices by Air-Hydraulic power by replacing the mechanical screw by Pneumatic-Hydraulic Blocking device as shown here to convert the mechanical modular vice into quick action air hydraulic vice for production setups. Six vices can be operated simultaneously with one power unit.

The "MULTIFLEX" series vises are a total new concept of modular clamping system able to maximize the machine table capacity and increase its productivity. The comb system even between the xed and movable jaw, increases and improves the clamping capacity. Each vice is supplied with 1 xed jaw and 4 xed-movable jaws, One "T" wrench, 1 pair of positioning key nuts and 4 workstops.

29

0

15

6

130

102M8

AIR INLET 1/4"

250

180

348

USER PORT 1/4"

The pump in its basic version is supplied complete with teon tank, ll plug, silencer, quick acting air connector tting and hydraulic control box.

D

B

E

C

TYPICAL ARRANGEMENTS

Outlet pressure can be regulated and set to desired pressure.

Art. 390 with Manual control valve

Art. 391 with Electrical control valve

Art. 392 with Air control valve CONVERT MECHANICAL VICE INTO

QUICK ACTING AIR HYDRAULIC VICE

STANDARD VICE TOWERS ART. 750 for Horizontal Machining Center

Art. 1 (Vices)

Art. 450 (Center Support)

Art. 828 (Head Plate)

MODULAR ELEMENTS

Art. 102 Movable section

Art. 104 Double xed section

Art. 103Fixed section

Available in different models having jaw width upto 300 mm with unlimited opening. Suitable for large size workpieces (single or double clamping).

WORLD RENOWNED MODULAR VISES

SOLD & SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

Also very suitable for operating swing Clamps (Single acting).

1514

Page 15: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

WORLD RENOWNED MODULAR VISES

SOLD & SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.Made in Italy

®

PRECISION MODULAR VISE 'STANDARD SERIES' WITH GUIDED MOVABLE JAW (ART. 1)

q High precision and gang operation

q Pull down easy to change jaws

q Unlimited longevity

q Space saving design

q No "wear" construction

q Unlimited clamping range

q All steel construction hardened and ground HRc60

JAW WIDTH

JAW DEPTH

MAX. JAW OPENING

ART. 11

VISE SIZE

100

30

100

2

125

40

150

3

150

50

4

175

60

5

200

65

6

300

80

200 300 200 300 400 500 200 300 400 500 600 200 300 400 500 600 700 800

A

B

C

D

E

F

G

H

I

J

K

L

M

N

VISE Art. 1

List of Optional Accessories

A Swivel base - ART. 105B Blocking support with hydraulic cylinder - A R T. 271C Hydraulic hand screw blocking device - ART. 257D Intermediate movable jaw with double step - A R T. 212E Floating movable jaw for round parts - ART. 210F Fixed stack type prismatic jaw - ART. 150G Fixed and movable stack-type jaws for round parts - A R T.131H Square stack-type jaws - ART. 138I Movable jaw with 2 oating segment s - ART. 190J Floating movable jaw - hydraulic control - A R T. 188K Step-prismatic guided movable jaw - A R T. 217L Guided movable jaw - straight plate - ART. 146M/N Extension for xed and movable jaw with screws - ART. 132/133

HYDRAULIC CLAMPING OPTION

OptionalAccessories

VISE WITH STANDARD ACCESSORIES

Mention vise size (jaw width) and max. jaw opening for ordering

MODULAR VISES "XL" SERIES

Art. 20Available in different models having jaw width up to 300 mm and jaw opening up to 1100 mm.

Art. 30Available in different models having jaw width up to 300 mm and jaw opening for two work pieces up to 460 mm each.

The hand hydraulic clamping group Art. 257 is an optional manual power multiplier alternative to the mechanical clamping of above vices. This device allows to reach the same clamping power reachable with the mechanical screw through a minimum effort. The hand hydraulic screw of Art. 257 is manually operated by the wrench included. All above Art. 1 vices can be purchased with Art. 257 tted.

Art. 257

1000 Kgf

Available in jaw width 49 mm, 74 mm and 99 mm having jaw opening up to 832 mm for single piece and up to 134 mm each for four work pieces held simultaneously.

1

DMax opening according to pieces to be clamped

300

400

500

600

700

B C E1 2 3 4 5 6 7 8 9

50

50

50

50

50

50

50

50

50

50

32/25

32/25

32/25

32/25

32/25

208

308

408

508

608

75

125

175

225

275

30

64

96

129

161

8

33

58

83

108

\

15

35

55

75

\

3

19

36

52

\

\

8

22

36

\

\

\

12

24

\

\

\

5

16

2

400

500

600

700

800

75

75

75

75

75

75

75

75

75

75

40

40

40

40

40

275

375

475

575

675

100

150

200

250

300

41

75

108

141

175

12

37

62

87

112

\

15

35

55

75

\

\

16

33

50

\

\

3

17

32

\

\

\

6

18

\

\

\

\

8

SIZE

3

700

800

900

1000

100

100

100

100

60

60

60

60

532

632

732

832

217

267

317

367

112

145

178

211

59

84

109

134

28

48

68

88

7

23

39

55

\

6

20

34

\

\

5

18

\

\

\

5

100

100

100

100

Made in Italy

®

HYDROPNEUMATIC POWER UNIT

Gerardi hydropneumatic power unit for hydraulic clamping devices and its bi-products is designed to meet all needs regarding the powering of hydraulic cylinders where low ow rates and high pressures are required. It is driven by air at its inlet to produce hydraulic pressure at its outlet. The special design shape of the power unit is such that a high performance system can be implemented taking up very little space. Thanks to the special design principles, the pump section adopted allows the hydropneumatic power unit to be installed in very hostile environments, such as the work area of machine tools, etc. The unique modular hydraulic ow control system allows controlling up to 6 separate users from just one power unit.

SPECIFICATION

MAX. PERMISSIBLE INLET AIR PRESSURE: 7 bar

RECOMMENDED INLET AIR PRESSURE: 5,5 bar

OIL DELIVERIES: 1.2-1.4-2.2-2.7-4.3 Liters/min

MAX. OIL OUTLET PRESSURE AT 5 BAR AIR INLET PRESSURE: 400 bar

MAX. NO. OF USERS RECOMMENDED: 6

PNEUMO - HYDRAULIC BLOCKING DEVICE

"MULTIFLEX" VICES ART. 600

Art. 393 - Power unit with Manual control, Art. 394 - Power unit with Pneumatic control, Art. 395 - Power unit with Electrical control

A bove power unit can be used to operate Mechanical Modular Vices by Air-Hydraulic power by replacing the mechanical screw by Pneumatic-Hydraulic Blocking device as shown here to convert the mechanical modular vice into quick action air hydraulic vice for production setups. Six vices can be operated simultaneously with one power unit.

The "MULTIFLEX" series vises are a total new concept of modular clamping system able to maximize the machine table capacity and increase its productivity. The comb system even between the xed and movable jaw, increases and improves the clamping capacity. Each vice is supplied with 1 xed jaw and 4 xed-movable jaws, One "T" wrench, 1 pair of positioning key nuts and 4 workstops.

29

0

15

6

130

102M8

AIR INLET 1/4"

250

180

348

USER PORT 1/4"

The pump in its basic version is supplied complete with teon tank, ll plug, silencer, quick acting air connector tting and hydraulic control box.

D

B

E

C

TYPICAL ARRANGEMENTS

Outlet pressure can be regulated and set to desired pressure.

Art. 390 with Manual control valve

Art. 391 with Electrical control valve

Art. 392 with Air control valve CONVERT MECHANICAL VICE INTO

QUICK ACTING AIR HYDRAULIC VICE

STANDARD VICE TOWERS ART. 750 for Horizontal Machining Center

Art. 1 (Vices)

Art. 450 (Center Support)

Art. 828 (Head Plate)

MODULAR ELEMENTS

Art. 102 Movable section

Art. 104 Double xed section

Art. 103Fixed section

Available in different models having jaw width upto 300 mm with unlimited opening. Suitable for large size workpieces (single or double clamping).

WORLD RENOWNED MODULAR VISES

SOLD & SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

Also very suitable for operating swing Clamps (Single acting).

1514

Page 16: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

ANGLE HEADS

ATC models for Automatic Tool Change and MTC models for Manual Tool Change machines

Case hardened and ground Shank and Shaft

Modular antirotation group

Graduated Ring

Output:- ER Collet (Standard)- Weldon- Shell Mill Holder- Special

Positioning Pin with Automatic Release

Standard 10BAR Coolant Through the Pin

Treated Steel Head Body º with 360 Position

Stop BlockWith case hardened bushing and gasket

BearingsAngular contact

preloaded ball bearings of precision class

ABEC7/9

GearsGleason ground spiral bevel gears maximum

performances and minimum vibration

SPINDLE SPEEDERS

Speed increase up to 1÷8 through two planetary

gears

Case hardened and ground shank and shaft

Standard 10Bar coolant through the pin

Output:- ER Collet (Standard)

- Weldon- Shell Mill Holder

- Special

OTHER PRODUCTS FROM GERARDI

MULTITASKING vises for 5 axis machining centers

Self-centering or eccentric

(Hydraulic or Pneumatic)

Immediate positioning & clamping of pallet, xture, vise or workpiece.

Zero Point

- Mazak - HAAS

- Biglia - Okuma

- Daewoo - Takisawa

- Mori seiki - VDI

- Nakamura

Gerardi Driven tools

Grid magnetic plates for milling

PlatformManual self-centeringscroll chucks

MULTIFLEX Vises and Vise Towers for multi-clamping

The most versatile

Tombstone for HorizontalMachining Center with Zero point or Grid type

WORLD RENOWNED ANGLE HEADS AND OTHER PRODUCTS

Made in Italy

®

Write to us for more details on products or visit www.gerardi.it®

SOLD & SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

LOCK DOWN JAW HYDRAULIC MACHINE VICE

‘SAFEWAY’ Lock Down Jaw Hydraulic Machine Vice has 'Down thrust semi-sphere segment' mechanism which eliminates jaw lift and work piece tilt. These vices have in-built hydraulic system hence do not require any external hydraulic line. Vice is operated by handle movement as in mechanical vices. Most suitable for Milling machine or Machining centre.

q High clamping force in forward as well as downward direction is achieved by effortless handle movement.q Extra large jaw opening.q Rigid Material-vice body made of ductile iron having 80,000 psi tensile strength.q Vice bed is ame hardened to HRC 45 which does not wear and maintains accuracy for long.

2 KGS of power in this directionProduce 1 KG of downward.Down thrust "semi-sphere segment"Mechanism-eliminates jaw lift and work-piece tilt.

MAX. OPENING CAPACITY

PHV-130

PHV-160

PHV-200

PHV-250

MODEL

130

160

200

250

JAW WIDTH

55

58

63

80

JAW DEPTH

MAX. JAWOPENING

OVERALLLENGTH

220

300

300

340

505

625

700

810

MC COMPACT HYDRAULIC VICE

This vise has all features of above PHV model including Lock down jaw mechanism. These vices have in-built hydraulic system hence do not require any external hydraulic line. Vice is operated by handle movement as in mechanical vices. Due to its compact design and accuracy, it is more suitable for machining centre for multiple vice setups.

CHV-100 V

CHV-130 V

CHV-160 V

CHV-200 V

MODEL

101

131

161

201

JAW WIDTH

48

55

58

63

JAW DEPTH

MAX. JAWOPENING

125

180

240

280

MAX. JAW OPENING WITH OPTIONAL JAW PLATES

320

380

470

540

Above vise is also available in one more model with 90° handle driving mechanism as shown below.

CHV-VD Modelwith 90° handle driving mechanism

Examples of Clamping

‘SAFEWAY’ Drill Grinding Machine is a portable machine used for Quick & Accurate grinding of Drill point.

q Easy operation, precision grinding by unskilled operator.q Diamond Wheel for long lasting service life and precise grinding angle.q Built-in collet bracket for easy management of collets (All sizes collets supplied with the machine).q Grinds point angle as well as chisel edge angle of a drill.q Can also grind solid carbide drills with optional Grinding Wheel.

Point angle

Chisel edge angle

Point Angle grinding & chisel edge angle grinding in two operations Rear View

Front View

DRILL GRINDING MACHINE

Optional Jaw Plates

MACHINING CENTRE VICES AND DRILL GRINDING MACHINE

OVERALLLENGTH

475

540

630

705

MODELDIA.

CAPACITYANGLE

CAPACITYPOWER

SA-1300

SA-2000

SA-2500

3Ø - 13Ø

3Ø - 20Ø

13Ø - 26Ø

90° - 144°

90° - 144°

90° - 144°

Single Phase AC -220 V

Single Phase AC -220 V

Single Phase AC -220 V

Ask us for detail catalogue of products

Taiwan

16 17

Page 17: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

ANGLE HEADS

ATC models for Automatic Tool Change and MTC models for Manual Tool Change machines

Case hardened and ground Shank and Shaft

Modular antirotation group

Graduated Ring

Output:- ER Collet (Standard)- Weldon- Shell Mill Holder- Special

Positioning Pin with Automatic Release

Standard 10BAR Coolant Through the Pin

Treated Steel Head Body º with 360 Position

Stop BlockWith case hardened bushing and gasket

BearingsAngular contact

preloaded ball bearings of precision class

ABEC7/9

GearsGleason ground spiral bevel gears maximum

performances and minimum vibration

SPINDLE SPEEDERS

Speed increase up to 1÷8 through two planetary

gears

Case hardened and ground shank and shaft

Standard 10Bar coolant through the pin

Output:- ER Collet (Standard)

- Weldon- Shell Mill Holder

- Special

OTHER PRODUCTS FROM GERARDI

MULTITASKING vises for 5 axis machining centers

Self-centering or eccentric

(Hydraulic or Pneumatic)

Immediate positioning & clamping of pallet, xture, vise or workpiece.

Zero Point

- Mazak - HAAS

- Biglia - Okuma

- Daewoo - Takisawa

- Mori seiki - VDI

- Nakamura

Gerardi Driven tools

Grid magnetic plates for milling

PlatformManual self-centeringscroll chucks

MULTIFLEX Vises and Vise Towers for multi-clamping

The most versatile

Tombstone for HorizontalMachining Center with Zero point or Grid type

WORLD RENOWNED ANGLE HEADS AND OTHER PRODUCTS

Made in Italy

®

Write to us for more details on products or visit www.gerardi.it®

SOLD & SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

LOCK DOWN JAW HYDRAULIC MACHINE VICE

‘SAFEWAY’ Lock Down Jaw Hydraulic Machine Vice has 'Down thrust semi-sphere segment' mechanism which eliminates jaw lift and work piece tilt. These vices have in-built hydraulic system hence do not require any external hydraulic line. Vice is operated by handle movement as in mechanical vices. Most suitable for Milling machine or Machining centre.

q High clamping force in forward as well as downward direction is achieved by effortless handle movement.q Extra large jaw opening.q Rigid Material-vice body made of ductile iron having 80,000 psi tensile strength.q Vice bed is ame hardened to HRC 45 which does not wear and maintains accuracy for long.

2 KGS of power in this directionProduce 1 KG of downward.Down thrust "semi-sphere segment"Mechanism-eliminates jaw lift and work-piece tilt.

MAX. OPENING CAPACITY

PHV-130

PHV-160

PHV-200

PHV-250

MODEL

130

160

200

250

JAW WIDTH

55

58

63

80

JAW DEPTH

MAX. JAWOPENING

OVERALLLENGTH

220

300

300

340

505

625

700

810

MC COMPACT HYDRAULIC VICE

This vise has all features of above PHV model including Lock down jaw mechanism. These vices have in-built hydraulic system hence do not require any external hydraulic line. Vice is operated by handle movement as in mechanical vices. Due to its compact design and accuracy, it is more suitable for machining centre for multiple vice setups.

CHV-100 V

CHV-130 V

CHV-160 V

CHV-200 V

MODEL

101

131

161

201

JAW WIDTH

48

55

58

63

JAW DEPTH

MAX. JAWOPENING

125

180

240

280

MAX. JAW OPENING WITH OPTIONAL JAW PLATES

320

380

470

540

Above vise is also available in one more model with 90° handle driving mechanism as shown below.

CHV-VD Modelwith 90° handle driving mechanism

Examples of Clamping

‘SAFEWAY’ Drill Grinding Machine is a portable machine used for Quick & Accurate grinding of Drill point.

q Easy operation, precision grinding by unskilled operator.q Diamond Wheel for long lasting service life and precise grinding angle.q Built-in collet bracket for easy management of collets (All sizes collets supplied with the machine).q Grinds point angle as well as chisel edge angle of a drill.q Can also grind solid carbide drills with optional Grinding Wheel.

Point angle

Chisel edge angle

Point Angle grinding & chisel edge angle grinding in two operations Rear View

Front View

DRILL GRINDING MACHINE

Optional Jaw Plates

MACHINING CENTRE VICES AND DRILL GRINDING MACHINE

OVERALLLENGTH

475

540

630

705

MODELDIA.

CAPACITYANGLE

CAPACITYPOWER

SA-1300

SA-2000

SA-2500

3Ø - 13Ø

3Ø - 20Ø

13Ø - 26Ø

90° - 144°

90° - 144°

90° - 144°

Single Phase AC -220 V

Single Phase AC -220 V

Single Phase AC -220 V

Ask us for detail catalogue of products

Taiwan

16 17

Page 18: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

‘GIN’ Hydraulic Machine Vice is a suitable hydraulic vice for Milling machine. Can also be used on a machining centre.

q Operates on handle movement as in mechanical vices.q High clamping force can be achieved by effortless handle movement

which e liminates h ammering on handle.

MILLING AND CNC ACCESSORIES

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. Taiwan

HYDRAULIC MACHINE VICE

MODEL

GIN-HVA-100-01GIN-HVA-125-01GIN-HVA-150-01GIN-HVA-200-01

JAW WIDTH

100125150200

JAW DEPTH

36465162

MAX. JAW OPENING

170220300300

UNIVERSAL 3-WAY ANGLE VICE

MODELJAW

WIDTH

GIN-VW3GIN-VW4GIN-VW5

80106132

303840

90105140

JAWDEPTH

MAX. JAWOPENING

HORIZONTAL AND VERTICAL ROTARY TABLE

Available in different sizes from 150 Ø to 400 Ø. Can be mounted horizontally as

well as vertically.

MODEL

GIN-HV150GIN-HV200GIN-HV250GIN-HV300GIN-HV350GIN-HV400

TABLEDIAMETER

150200250300350400

ELECTRONIC (OPTICAL) EDGE FINDER

GIN TSOE 20S

GIN TSOE 20L

GIN TSOE 20LB

MODEL

20

20

20

BALL DIA

‘GIN’ Electron icedge nder with LED is most convenient to use as the tip of the Touch Probe is brought near the edge of the job, red light powered by enclosed battery glows as the ball probe comes in contact with the edge.

q C oncentricity of ball-probe and shank within 0.005 mm.

q Repeatability of work location within 0.01mm.

q Spring loaded Ball-probe to prevent damage of probe.

TOTAL LENGTH

120

158

158

10

10

10

SHANKDIA

TYPE

WITH LED ONLY

WITH LED ONLY

WITH LED AND BEEPER

Z-AXIS ZERO SETTER - Model Z-50

Z-Axis Zero Setter is used for zero setting of tool height from the machine table on machining centres. Setting height : 50.00±0.01mm

Features:

q Large measuring surface to assure high measuring accuracy.

q Low Spring force to avoid breakage of small end mill and drill.

q Easy to calibrate by a ground parallel or gauge block.

48

3

50+0.005

68Ø

0

Different types of shanks are also available separately.

PRECISION KEYLESS DRILL CHUCK

APU08-J 1APU10-J 2APU13-J 6APU16-J 6

MODEL

0-80-101-133-16

CAPACITY

J 1J 2SJ 6J 6

TAPER

High quality Keyless Drill Chuck is most suitable for CNC and Milling machines.

The compact designed drill chuck provides higher accuracy, improved rigidity, and shorter overhang for holding drills.

Preventing from slip-out during machining, absolutely eliminating the disadvantage of connecting by taper. A dedicated Spanner is provided for powerful clamping.

Available in BT 30/40/50 and HSK shank having holding capacities 0-8 mm, 1-13 mm and 3-16 mm.

NC DRILL CHUCK - INTEGRATED TYPE

Z-AXIS PRESET GAUGE - OPTICAL TYPE Model GIN-ZOP-50

Used for setting tool height 50mm. Its base has a built-in magnet hence can be used vertically as well as horizontally. The red lamp lights up when touched. Height can be micro adjusted by gauge block.

BT TYPE TAPER WIPER

MODEL FOR SPINDLE TAPER

GIN-W30GIN-W40GIN-W50

BT-30BT-40BT-50

Z-AXIS ZERO SETTER - ZPM Series - Ceramic

q L east measuring diameter of cutting tool : 0.1mmq S cratch proof ceramic measuring face

Model GIN-BS-2 dividing head comes with complete set of gears and dividing plates. Centre height is 132mm and ratio of worm to gear is 1:40.

UNIVERSAL DIVIDING HEAD-Model GIN-BS-2

ZPM-50/50P ZPM-100P

CERAMIC EDGE FINDER

Tips are made of Ceramic having 10 dia.

TSEP 1020BTSEP 1020TSEP10

MODEL BASE TYPE

ZPM-50

ZPM-50 P

ZPM-100 P

Plain

Magnetic

Magnetic ON/OFF

'GIN' BHC Series Boring Heads have wide base bearing surface that assures maximum rigidity even when the bar holder is in an offset position. The adjustment screw is ground after hardening. Shanks of different types and boring tools available seperately.

Different types of shanks are also available separately.

MODELOUTER

DIABORING BAR

HOLE SIZEOFFSET

CROSSHOLE DIA

GIN-BHC2GIN-BHC3GIN-BHC4

5075

100

121825

121825

152525

0.010.010.01

PRECISION MICRO BORING HEADS AND SETS

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. Taiwan

UNIVERSAL BORING AND FACING MASTER HEAD

Universal Boring and Facing Head model GIN-BHAM has very precise construction with auto feed and stop. Working range is 5 mm to 250 mm.

Available complete with boring bars, boring tools etc. with different shanks such as BT40, BT50, R8, NT30, NT40, NT50, MT3, MT4,MT5.

18

CROSS HOLEDIAMETER

18

BORING BARHOLE SIZE

15

OFFSET

Model GIN-BHAM (SET)

BORING HEAD SETS AND BORING TOOLS

Sets available with different interchangeable shanks such as R8, NT30, NT40, NT50, MT2, MT3, MT4, MT5, BT40 & BT50.

MODEL GIN-BHC2 (SET) WITH THREE NOS. INDEXABLE INSERTS TYPE BORING BARS.

0.01 mm

BORING HEAD OUTER DIA

MIN. BORING DIA

MAX.BORING DIA

MAX. BORINGDEPTH

BORING BARHOLE SIZE

8 mm 90 mm* 45 mm 12 mm

LEAST COUNT

50

Sets available with different interchangeable shanks such as R8, NT30, NT40, NT50, MT2, MT3, MT4, MT5, BT40 & BT50.

MODEL GIN-BHC3 (SET) WITH THREE NOS. INDEXABLE INSERTS TYPE BORING BARS.

75

BORING HEAD OUTER DIA

MIN. BORING DIA

MAX.BORING DIA

MAX. BORINGDEPTH

BORING BARHOLE SIZE

12 mm 140 mm* 90 mm 18 mm 0.01 mm

LEAST COUNT

Boring tools available in shank dia 12mm and shank dia 18mm for BHC2 and BHC3 boring heads respectively. These boring tools are available in different sizes and lengths to achieve different sizes of bores.Side type boring tools to be used in cross hole of boring head for large diameter boring are also available.

PRECISION BORING TOOLS - WITH INDEXABLE CARBIDE INSERTS

Complete with boring tools available with different interchangeable shanks such as R8, NT30, NT40, NT50, MT3, MT4, MT5, BT40 & BT50.

MODEL GIN-BH2084 (SET) WITH EIGHT NOS. INDEXABLE INSERTS TYPE BORING BARS.

0.005 mm

BORING HEAD OUTER DIA

MIN. BORING DIA

MAX.BORING DIA

BORING BARHOLE SIZE

8 mm 280 mm 20 mm 84 mm

LEAST COUNT

Standard sets are with indexable inserts type carbide boring tools.

*Larger boring dia upto 200mm can be achieved by optional cross hole boring tool with HSS Boring bit (GIN Model 5958-902063) available separately.

* Larger boring dia upto 250mm can be achieved by optional cross hole boring tool with indexable insert (GIN Model 5952-BH18-36) available separately.

BORING HEAD - BHC Series

BORING HEAD - HIGH PRECISION FOR SMALL DIAMETER

GIN-BHW02 Series Boring head is high precision boring head most suitable for small diameters ranging from 3Ø to 50Ø. Different boring tools for different sizes of bores are available seperately. All types of shanks are also available separately.

63.5

OUTERDIA.

GIN-BHW02-50CK6

MODEL

16

BORING BARHOLE SIZE

OFFSETLEASTCOUNT

4.5 0.001

LEASTCOUNT

MAX.BORING DEPTH

110 mm

1918

Page 19: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

‘GIN’ Hydraulic Machine Vice is a suitable hydraulic vice for Milling machine. Can also be used on a machining centre.

q Operates on handle movement as in mechanical vices.q High clamping force can be achieved by effortless handle movement

which e liminates h ammering on handle.

MILLING AND CNC ACCESSORIES

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. Taiwan

HYDRAULIC MACHINE VICE

MODEL

GIN-HVA-100-01GIN-HVA-125-01GIN-HVA-150-01GIN-HVA-200-01

JAW WIDTH

100125150200

JAW DEPTH

36465162

MAX. JAW OPENING

170220300300

UNIVERSAL 3-WAY ANGLE VICE

MODELJAW

WIDTH

GIN-VW3GIN-VW4GIN-VW5

80106132

303840

90105140

JAWDEPTH

MAX. JAWOPENING

HORIZONTAL AND VERTICAL ROTARY TABLE

Available in different sizes from 150 Ø to 400 Ø. Can be mounted horizontally as

well as vertically.

MODEL

GIN-HV150GIN-HV200GIN-HV250GIN-HV300GIN-HV350GIN-HV400

TABLEDIAMETER

150200250300350400

ELECTRONIC (OPTICAL) EDGE FINDER

GIN TSOE 20S

GIN TSOE 20L

GIN TSOE 20LB

MODEL

20

20

20

BALL DIA

‘GIN’ Electron icedge nder with LED is most convenient to use as the tip of the Touch Probe is brought near the edge of the job, red light powered by enclosed battery glows as the ball probe comes in contact with the edge.

q C oncentricity of ball-probe and shank within 0.005 mm.

q Repeatability of work location within 0.01mm.

q Spring loaded Ball-probe to prevent damage of probe.

TOTAL LENGTH

120

158

158

10

10

10

SHANKDIA

TYPE

WITH LED ONLY

WITH LED ONLY

WITH LED AND BEEPER

Z-AXIS ZERO SETTER - Model Z-50

Z-Axis Zero Setter is used for zero setting of tool height from the machine table on machining centres. Setting height : 50.00±0.01mm

Features:

q Large measuring surface to assure high measuring accuracy.

q Low Spring force to avoid breakage of small end mill and drill.

q Easy to calibrate by a ground parallel or gauge block.

48

3

50+0.005

68Ø

0

Different types of shanks are also available separately.

PRECISION KEYLESS DRILL CHUCK

APU08-J 1APU10-J 2APU13-J 6APU16-J 6

MODEL

0-80-101-133-16

CAPACITY

J 1J 2SJ 6J 6

TAPER

High quality Keyless Drill Chuck is most suitable for CNC and Milling machines.

The compact designed drill chuck provides higher accuracy, improved rigidity, and shorter overhang for holding drills.

Preventing from slip-out during machining, absolutely eliminating the disadvantage of connecting by taper. A dedicated Spanner is provided for powerful clamping.

Available in BT 30/40/50 and HSK shank having holding capacities 0-8 mm, 1-13 mm and 3-16 mm.

NC DRILL CHUCK - INTEGRATED TYPE

Z-AXIS PRESET GAUGE - OPTICAL TYPE Model GIN-ZOP-50

Used for setting tool height 50mm. Its base has a built-in magnet hence can be used vertically as well as horizontally. The red lamp lights up when touched. Height can be micro adjusted by gauge block.

BT TYPE TAPER WIPER

MODEL FOR SPINDLE TAPER

GIN-W30GIN-W40GIN-W50

BT-30BT-40BT-50

Z-AXIS ZERO SETTER - ZPM Series - Ceramic

q L east measuring diameter of cutting tool : 0.1mmq S cratch proof ceramic measuring face

Model GIN-BS-2 dividing head comes with complete set of gears and dividing plates. Centre height is 132mm and ratio of worm to gear is 1:40.

UNIVERSAL DIVIDING HEAD-Model GIN-BS-2

ZPM-50/50P ZPM-100P

CERAMIC EDGE FINDER

Tips are made of Ceramic having 10 dia.

TSEP 1020BTSEP 1020TSEP10

MODEL BASE TYPE

ZPM-50

ZPM-50 P

ZPM-100 P

Plain

Magnetic

Magnetic ON/OFF

'GIN' BHC Series Boring Heads have wide base bearing surface that assures maximum rigidity even when the bar holder is in an offset position. The adjustment screw is ground after hardening. Shanks of different types and boring tools available seperately.

Different types of shanks are also available separately.

MODELOUTER

DIABORING BAR

HOLE SIZEOFFSET

CROSSHOLE DIA

GIN-BHC2GIN-BHC3GIN-BHC4

5075

100

121825

121825

152525

0.010.010.01

PRECISION MICRO BORING HEADS AND SETS

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD. Taiwan

UNIVERSAL BORING AND FACING MASTER HEAD

Universal Boring and Facing Head model GIN-BHAM has very precise construction with auto feed and stop. Working range is 5 mm to 250 mm.

Available complete with boring bars, boring tools etc. with different shanks such as BT40, BT50, R8, NT30, NT40, NT50, MT3, MT4,MT5.

18

CROSS HOLEDIAMETER

18

BORING BARHOLE SIZE

15

OFFSET

Model GIN-BHAM (SET)

BORING HEAD SETS AND BORING TOOLS

Sets available with different interchangeable shanks such as R8, NT30, NT40, NT50, MT2, MT3, MT4, MT5, BT40 & BT50.

MODEL GIN-BHC2 (SET) WITH THREE NOS. INDEXABLE INSERTS TYPE BORING BARS.

0.01 mm

BORING HEAD OUTER DIA

MIN. BORING DIA

MAX.BORING DIA

MAX. BORINGDEPTH

BORING BARHOLE SIZE

8 mm 90 mm* 45 mm 12 mm

LEAST COUNT

50

Sets available with different interchangeable shanks such as R8, NT30, NT40, NT50, MT2, MT3, MT4, MT5, BT40 & BT50.

MODEL GIN-BHC3 (SET) WITH THREE NOS. INDEXABLE INSERTS TYPE BORING BARS.

75

BORING HEAD OUTER DIA

MIN. BORING DIA

MAX.BORING DIA

MAX. BORINGDEPTH

BORING BARHOLE SIZE

12 mm 140 mm* 90 mm 18 mm 0.01 mm

LEAST COUNT

Boring tools available in shank dia 12mm and shank dia 18mm for BHC2 and BHC3 boring heads respectively. These boring tools are available in different sizes and lengths to achieve different sizes of bores.Side type boring tools to be used in cross hole of boring head for large diameter boring are also available.

PRECISION BORING TOOLS - WITH INDEXABLE CARBIDE INSERTS

Complete with boring tools available with different interchangeable shanks such as R8, NT30, NT40, NT50, MT3, MT4, MT5, BT40 & BT50.

MODEL GIN-BH2084 (SET) WITH EIGHT NOS. INDEXABLE INSERTS TYPE BORING BARS.

0.005 mm

BORING HEAD OUTER DIA

MIN. BORING DIA

MAX.BORING DIA

BORING BARHOLE SIZE

8 mm 280 mm 20 mm 84 mm

LEAST COUNT

Standard sets are with indexable inserts type carbide boring tools.

*Larger boring dia upto 200mm can be achieved by optional cross hole boring tool with HSS Boring bit (GIN Model 5958-902063) available separately.

* Larger boring dia upto 250mm can be achieved by optional cross hole boring tool with indexable insert (GIN Model 5952-BH18-36) available separately.

BORING HEAD - BHC Series

BORING HEAD - HIGH PRECISION FOR SMALL DIAMETER

GIN-BHW02 Series Boring head is high precision boring head most suitable for small diameters ranging from 3Ø to 50Ø. Different boring tools for different sizes of bores are available seperately. All types of shanks are also available separately.

63.5

OUTERDIA.

GIN-BHW02-50CK6

MODEL

16

BORING BARHOLE SIZE

OFFSETLEASTCOUNT

4.5 0.001

LEASTCOUNT

MAX.BORING DEPTH

110 mm

1918

Page 20: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

20 21

Page 21: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

20 21

Page 22: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

OTHER GIN PRODUCTS

Taiwan

PUNCH FORMER (BIG) 3 JAWS PUNCH FORMER MOTOR PUNCH FORMERER COLLET PUNCH FORMER

WHEEL BALANCING STANDUNIVERSAL WHEEL DRESSER FLANGES FOR GRINDING MACHINESDIAMOND CBN FLAT WHEEL TRUER

UNIVERSAL TILTING ROTARY TABLESUPER INDEX SPACER CHAMFERING MACHINES UNIVERSAL CUTTER GRINDER

PERMANENT MAGNETIC CHUCK ROTARY PERMANENT MAGNETIC CHUCK

PERMANENT MAGNETIC CHUCK (VERTICAL TYPE)

ELECTRICALLY CONTROLLEDPERMANENT MAGNETIC

CHUCK

PIN GAUGE SETGAUGE BLOCKS DEMAGNETIZER - HANDY TYPE & STANDARD TYPE

SUPER THIN CHUCKS FOR MILLING

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

NEW GIN PRODUCTS

Taiwan

Ask us for detail catalogue of products or visit www.ginchan.com.tw

WIRE EDM CLAMP CLAMP KIT FOR WIREEDM S.S. PRECISION VISE FOR WIREEDM

ADJUSTABLE FIXTURES AND VISES FOR WIREEDM

FIXTURES AND ELEMENTS FOR CMMCENTER PUNCH FORMER PRECISION UNIVERSAL THIN CHUCK PAEDESTAL

THREAD GRINDING SLIDER

BALL ENDMILL GRINDERCUTTING-OFF MACHINE SCREW TAP GRINDER AIR TAPPING MACHINE

3D TASTER CONCENTRICITY MEASURING INSTRUMENTCENTERING INDICATOR TOOL PRE-SETTER

LARGE DIA BORING HEADSMALL DIA FINE BORING HEAD QUICK CHANGE TAPPING CHUCKS

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

MICRO BORING HEAD

2322

Page 23: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

OTHER GIN PRODUCTS

Taiwan

PUNCH FORMER (BIG) 3 JAWS PUNCH FORMER MOTOR PUNCH FORMERER COLLET PUNCH FORMER

WHEEL BALANCING STANDUNIVERSAL WHEEL DRESSER FLANGES FOR GRINDING MACHINESDIAMOND CBN FLAT WHEEL TRUER

UNIVERSAL TILTING ROTARY TABLESUPER INDEX SPACER CHAMFERING MACHINES UNIVERSAL CUTTER GRINDER

PERMANENT MAGNETIC CHUCK ROTARY PERMANENT MAGNETIC CHUCK

PERMANENT MAGNETIC CHUCK (VERTICAL TYPE)

ELECTRICALLY CONTROLLEDPERMANENT MAGNETIC

CHUCK

PIN GAUGE SETGAUGE BLOCKS DEMAGNETIZER - HANDY TYPE & STANDARD TYPE

SUPER THIN CHUCKS FOR MILLING

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

NEW GIN PRODUCTS

Taiwan

Ask us for detail catalogue of products or visit www.ginchan.com.tw

WIRE EDM CLAMP CLAMP KIT FOR WIREEDM S.S. PRECISION VISE FOR WIREEDM

ADJUSTABLE FIXTURES AND VISES FOR WIREEDM

FIXTURES AND ELEMENTS FOR CMMCENTER PUNCH FORMER PRECISION UNIVERSAL THIN CHUCK PAEDESTAL

THREAD GRINDING SLIDER

BALL ENDMILL GRINDERCUTTING-OFF MACHINE SCREW TAP GRINDER AIR TAPPING MACHINE

3D TASTER CONCENTRICITY MEASURING INSTRUMENTCENTERING INDICATOR TOOL PRE-SETTER

LARGE DIA BORING HEADSMALL DIA FINE BORING HEAD QUICK CHANGE TAPPING CHUCKS

SOLD AND SERVICED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

MICRO BORING HEAD

2322

Page 24: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

MILLING AND CNC ACCESSORIES

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

ER COLLETS AND COLLET CHUCK SETS

Following sizes of ER Collet & Collet Chuck sets with spanner in an attractive plastic carry box are available.

ER 32 - BT - 30

15 Pieces Collet Sizes Included In Set

Collet Chuck SetWith Spanner

3-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 12-11, 14-13, 15-14, 16-15, 17-16,

18-17, 20-19

ER 40 - BT - 503-2, 4-3, 5-4, 6-5, 8-7, 10-9, 12-11, 14-13, 15-14, 16-15, 18-17, 20-19,

22-21, 24-23, 26-25

3-2, 4-3, 5-4, 6-5, 8-7, 10-9, 12-11, 14-13, 15-14, 16-15, 18-17, 20-19,

22-21, 24-23, 26-25ER 40 - BT - 40

ER 32 - BT - 403-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 12-11, 14-13, 15-14, 16-15, 17-16,

18-17, 20-19

All below given sizes of ER Collets are available in single piece packing.

ER SPRING COLLETS as per DIN 6499

Collet Type Size - Diameter Range (mm)

ER16 1-0.5, 1.5-1, 2-1.5, 3 -2, 4-3, 5-4, 6-5, 7-6, 8-7,

9-8, 10-9

ER 20 1-0.5, 1.5-1, 2-1.5, 3 -2, 4-3, 5-4, 6-5, 7-6, 8-7,

9-8, 10-9, 11-10, 12-11, 13-12

ER 25 1-0.5, 1.5-1, 2-1.5, 3 -2, 4-3, 5-4, 6-5, 7-6, 8-7,

9-8, 10-9, 11-10, 12-11, 13-12, 14-13, 15-14,

16-15

ER 32 1-0.5, 1.5-1, 2-1.5, 3-2, 3.5-2.5, 4-3, 5-4, 6-5,

7-6, 8-7, 9-8, 10-9, 11-10, 12-11, 13-12, 14-

13, 15-14, 16-15, 17-16, 18-17, 19-18, 20-19

ER 40 3-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 11-10,

12-11, 13-12, 14-13, 15-14, 16-15, 17-16,

18-17, 19-18, 20-19, 21-20, 22-21, 23-22,

24-23, 25-24, 26-25, 27-26, 28-27, 29-28,

30-29

3-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 12-11, 14-13, 15-14, 16-15, 17-16,

18-17, 20-19 ER 32 - BT - 50

DRILLING AND MILLING ACCESSORIES

Following sizes of Pull Studs are available:

PULL STUDS - MAS 403

Sizes

PS - BT30 - 30°

PS - BT30 - 45°

PS - BT40 - 30°

Sizes

PS - BT40 - 45°

PS - BT50 - 30°

PS - BT50 - 45°

Used for tightening the tool in the tool holder outside the machine.

HORIZONTAL / VERTICAL CNC TOOL TIGHTENING FIXTURE

TTF-BT-50

TTF-BT-40

TTF-BT-30 BT-30

BT-40

BT-50

Model Taper

Following spanners are available for tightening and loosening collet chucks of respective sizes.

ER SPANNER

Sizes

ER16 - Open Ended Spanner Type

ER20 - Open Ended Spanner Type

Sizes

ER25 - Star Type

ER32 - Star Type

ER40 - Star Type

Open Ended Type

Star Type

Hardened high grade steel, precision ground.

ER COLLECT CHUCKS

Sizes Sizes

BT30 - ER16 x 70

BT30 - ER20 x 70

BT30 - ER25 x 70

BT30 - ER32 x 70

BT30 - ER40 x 80

BT40 - ER16 x 70

BT40 - ER20 x 70

BT40 - ER25 x 70

BT40 - ER32 x 70

BT40 - ER32 x 100

BT40 - ER40 x 80

BT50 - ER16 x 70

BT50 - ER20 x 70

BT50 - ER25 x 70

BT50 - ER32 x 80

BT50 - ER40 x 80

Hardened high grade steel, precision ground.

SIDE LOCK ADAPTOR (End Mill Holder)

Sizes

BT40 - SLA 8 dia x 50

BT40 - SLA 10 dia x 63

BT40 - SLA 12 dia x 63

BT40 - SLA 16 dia x 63

BT40 - SLA 20 dia x 70

BT40 - SLA 25 dia x 90

Sizes

BT40 - SLA 32 dia x 100

BT40 - SLA 40 dia x 120

BT50 - SLA 20 dia x 80

BT50 - SLA 25 dia x 100

BT50 - SLA 32 dia x 100

BT50 - SLA 40 dia x 120

Hardened high grade steel, precision ground.

SHELL MILL ARBOR

Sizes

BT40 - 22 dia x 60

BT40 - 22 dia x 100

BT40 - 27 dia x 60

BT40 - 27 dia x 105

Sizes

BT40 - 32 dia x 60

BT50 - 27 dia x 105

BT50 - 32 dia x 60

UNIVERSAL ARM MAGNETIC STAND : Model MS-80

q Rigid locking of the stand by one central knob.

q Magnetic Base with ON / OFF Switch size : H55 x W50 x L63.

q Magnetic Pull : 80 Kgs.

q Dial Holder hole ID = 8mm with micro adjustment.

q Main stem height = 290 mm.

SOGGOMARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

2928

TWO-WAY ANGLE MILLING VICE

Model

STW-4

STW-5

STW-6

100

125

160

41

45

50

Max. Jaw Opening

80

95

125

Jaw DepthJaw Width

q Made of high grade cast iron.

q The vice can be adjusted and locked at any angle from the horizontal position to the vertical position and also has swivelling base with rotation of 360°.

q Parallelism and square within 0.025mm/100mm.

q Special segment mechanism minimizes jaw lift and Workpiece tilt.

q Ductile iron construction for high durability.

ANGLOCK MILLING VICE

Model

SLV-4

SLV-6

SLV-6L

SLV-8

100

160

160

200

32

45

45

50

Max. Jaw Opening

100

150

190

190

Jaw DepthJaw Width

All above models available with or without swivel base.

OverallLength

310

412

425

500

UNIVERSAL INDEX CENTER (DIVIDING HEAD)

Standard accessories include dividing plate A, B, C, tail stock and complete set of gears.

SEMI - UNIVERSAL INDEX CENTER (DIVIDING HEAD)

‘SOGGO’ Universal Index Centre has been designed to carry out all types of gear cutting. The center face can be tilted from a horizontal position of 90° down to -10° from vertical, and inclinations can be read off a scale graduated in degrees. The center is built to highest engineering standards and is factory inspected and tested to assure complete satisfaction. The ratio of worm to gear is 1:40.

Standard accessories include dividing plate A, B, C and tail stock.

Chuck not included.

Chuck not included.

Model

SBS - 2

Centre Height

133

Centre Taper

MT4

Model

SBS - 0

Centre Height

100

Centre Taper

MT2

SBS - 1 128 MT3

SOGGO

2524

Most suitable for production setups on Drilling or Light milling operations. Rapid Clamping / Locking and quick release of workpiece saves cycle time.

QUICK ACTION DRILL VICE

Model

SQV-100 100 38

Max. Jaw Opening

100

Jaw DepthJaw Width

Heavy cast iron construction for rigid clamping.

DRILL MACHINE VICE - HEAVY DUTY

Model

SDV-100 100 46

Max. Jaw Opening

102

Jaw DepthJaw Width

SDV-150 160 52 152

PERMANENT MAGNETIC LIFTER

‘SOGGO’ High power permanent magnets ensure steady power for an unlimited period. All lifting magnets are tested as per safety factor of 1:3.5.

Model

SMPL-1000

Lifting Capacity

1000 kgs

SPML-100

SPML-300

SPML-600

100 kgs

300 kgs

600 kgs

SPML-2000

SPML-3000

2000 kgs

3000 kgs

Model

SHV-4 110

Table Dia

Available in different sizes from 110Ø to 400Ø. Can be mounted horizontally as well as vertically.

HORIZONTAL AND VERTICAL ROTARY TABLE

SHV-16 400

SHV-6 150

SHV-8 200

SHV-12 300

SHV-14 350

SHV-10 250

‘SOGO’ Semi - Universal Index Centre is a simplied type of Universal Index Center and can be used for direct and indirect dividing. No accessories for the differential dividing and spiral work are included. The direct index plate of 24 and three plates in the standard accessories make the indirect dividing possible in any number from 2 to 50 and in certain numbers up to 380.

SSP47MSSP66MSSP510MSSP612M

Page 25: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

MILLING AND CNC ACCESSORIES

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

ER COLLETS AND COLLET CHUCK SETS

Following sizes of ER Collet & Collet Chuck sets with spanner in an attractive plastic carry box are available.

ER 32 - BT - 30

15 Pieces Collet Sizes Included In Set

Collet Chuck SetWith Spanner

3-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 12-11, 14-13, 15-14, 16-15, 17-16,

18-17, 20-19

ER 40 - BT - 503-2, 4-3, 5-4, 6-5, 8-7, 10-9, 12-11, 14-13, 15-14, 16-15, 18-17, 20-19,

22-21, 24-23, 26-25

3-2, 4-3, 5-4, 6-5, 8-7, 10-9, 12-11, 14-13, 15-14, 16-15, 18-17, 20-19,

22-21, 24-23, 26-25ER 40 - BT - 40

ER 32 - BT - 403-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 12-11, 14-13, 15-14, 16-15, 17-16,

18-17, 20-19

All below given sizes of ER Collets are available in single piece packing.

ER SPRING COLLETS as per DIN 6499

Collet Type Size - Diameter Range (mm)

ER16 1-0.5, 1.5-1, 2-1.5, 3 -2, 4-3, 5-4, 6-5, 7-6, 8-7,

9-8, 10-9

ER 20 1-0.5, 1.5-1, 2-1.5, 3 -2, 4-3, 5-4, 6-5, 7-6, 8-7,

9-8, 10-9, 11-10, 12-11, 13-12

ER 25 1-0.5, 1.5-1, 2-1.5, 3 -2, 4-3, 5-4, 6-5, 7-6, 8-7,

9-8, 10-9, 11-10, 12-11, 13-12, 14-13, 15-14,

16-15

ER 32 1-0.5, 1.5-1, 2-1.5, 3-2, 3.5-2.5, 4-3, 5-4, 6-5,

7-6, 8-7, 9-8, 10-9, 11-10, 12-11, 13-12, 14-

13, 15-14, 16-15, 17-16, 18-17, 19-18, 20-19

ER 40 3-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 11-10,

12-11, 13-12, 14-13, 15-14, 16-15, 17-16,

18-17, 19-18, 20-19, 21-20, 22-21, 23-22,

24-23, 25-24, 26-25, 27-26, 28-27, 29-28,

30-29

3-2, 4-3, 5-4, 6-5, 7-6, 8-7, 9-8, 10-9, 12-11, 14-13, 15-14, 16-15, 17-16,

18-17, 20-19 ER 32 - BT - 50

DRILLING AND MILLING ACCESSORIES

Following sizes of Pull Studs are available:

PULL STUDS - MAS 403

Sizes

PS - BT30 - 30°

PS - BT30 - 45°

PS - BT40 - 30°

Sizes

PS - BT40 - 45°

PS - BT50 - 30°

PS - BT50 - 45°

Used for tightening the tool in the tool holder outside the machine.

HORIZONTAL / VERTICAL CNC TOOL TIGHTENING FIXTURE

TTF-BT-50

TTF-BT-40

TTF-BT-30 BT-30

BT-40

BT-50

Model Taper

Following spanners are available for tightening and loosening collet chucks of respective sizes.

ER SPANNER

Sizes

ER16 - Open Ended Spanner Type

ER20 - Open Ended Spanner Type

Sizes

ER25 - Star Type

ER32 - Star Type

ER40 - Star Type

Open Ended Type

Star Type

Hardened high grade steel, precision ground.

ER COLLECT CHUCKS

Sizes Sizes

BT30 - ER16 x 70

BT30 - ER20 x 70

BT30 - ER25 x 70

BT30 - ER32 x 70

BT30 - ER40 x 80

BT40 - ER16 x 70

BT40 - ER20 x 70

BT40 - ER25 x 70

BT40 - ER32 x 70

BT40 - ER32 x 100

BT40 - ER40 x 80

BT50 - ER16 x 70

BT50 - ER20 x 70

BT50 - ER25 x 70

BT50 - ER32 x 80

BT50 - ER40 x 80

Hardened high grade steel, precision ground.

SIDE LOCK ADAPTOR (End Mill Holder)

Sizes

BT40 - SLA 8 dia x 50

BT40 - SLA 10 dia x 63

BT40 - SLA 12 dia x 63

BT40 - SLA 16 dia x 63

BT40 - SLA 20 dia x 70

BT40 - SLA 25 dia x 90

Sizes

BT40 - SLA 32 dia x 100

BT40 - SLA 40 dia x 120

BT50 - SLA 20 dia x 80

BT50 - SLA 25 dia x 100

BT50 - SLA 32 dia x 100

BT50 - SLA 40 dia x 120

Hardened high grade steel, precision ground.

SHELL MILL ARBOR

Sizes

BT40 - 22 dia x 60

BT40 - 22 dia x 100

BT40 - 27 dia x 60

BT40 - 27 dia x 105

Sizes

BT40 - 32 dia x 60

BT50 - 27 dia x 105

BT50 - 32 dia x 60

UNIVERSAL ARM MAGNETIC STAND : Model MS-80

q Rigid locking of the stand by one central knob.

q Magnetic Base with ON / OFF Switch size : H55 x W50 x L63.

q Magnetic Pull : 80 Kgs.

q Dial Holder hole ID = 8mm with micro adjustment.

q Main stem height = 290 mm.

SOGGOMARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

2928

TWO-WAY ANGLE MILLING VICE

Model

STW-4

STW-5

STW-6

100

125

160

41

45

50

Max. Jaw Opening

80

95

125

Jaw DepthJaw Width

q Made of high grade cast iron.

q The vice can be adjusted and locked at any angle from the horizontal position to the vertical position and also has swivelling base with rotation of 360°.

q Parallelism and square within 0.025mm/100mm.

q Special segment mechanism minimizes jaw lift and Workpiece tilt.

q Ductile iron construction for high durability.

ANGLOCK MILLING VICE

Model

SLV-4

SLV-6

SLV-6L

SLV-8

100

160

160

200

32

45

45

50

Max. Jaw Opening

100

150

190

190

Jaw DepthJaw Width

All above models available with or without swivel base.

OverallLength

310

412

425

500

UNIVERSAL INDEX CENTER (DIVIDING HEAD)

Standard accessories include dividing plate A, B, C, tail stock and complete set of gears.

SEMI - UNIVERSAL INDEX CENTER (DIVIDING HEAD)

‘SOGGO’ Universal Index Centre has been designed to carry out all types of gear cutting. The center face can be tilted from a horizontal position of 90° down to -10° from vertical, and inclinations can be read off a scale graduated in degrees. The center is built to highest engineering standards and is factory inspected and tested to assure complete satisfaction. The ratio of worm to gear is 1:40.

Standard accessories include dividing plate A, B, C and tail stock.

Chuck not included.

Chuck not included.

Model

SBS - 2

Centre Height

133

Centre Taper

MT4

Model

SBS - 0

Centre Height

100

Centre Taper

MT2

SBS - 1 128 MT3

SOGGO

2524

Most suitable for production setups on Drilling or Light milling operations. Rapid Clamping / Locking and quick release of workpiece saves cycle time.

QUICK ACTION DRILL VICE

Model

SQV-100 100 38

Max. Jaw Opening

100

Jaw DepthJaw Width

Heavy cast iron construction for rigid clamping.

DRILL MACHINE VICE - HEAVY DUTY

Model

SDV-100 100 46

Max. Jaw Opening

102

Jaw DepthJaw Width

SDV-150 160 52 152

PERMANENT MAGNETIC LIFTER

‘SOGGO’ High power permanent magnets ensure steady power for an unlimited period. All lifting magnets are tested as per safety factor of 1:3.5.

Model

SMPL-1000

Lifting Capacity

1000 kgs

SPML-100

SPML-300

SPML-600

100 kgs

300 kgs

600 kgs

SPML-2000

SPML-3000

2000 kgs

3000 kgs

Model

SHV-4 110

Table Dia

Available in different sizes from 110Ø to 400Ø. Can be mounted horizontally as well as vertically.

HORIZONTAL AND VERTICAL ROTARY TABLE

SHV-16 400

SHV-6 150

SHV-8 200

SHV-12 300

SHV-14 350

SHV-10 250

‘SOGO’ Semi - Universal Index Centre is a simplied type of Universal Index Center and can be used for direct and indirect dividing. No accessories for the differential dividing and spiral work are included. The direct index plate of 24 and three plates in the standard accessories make the indirect dividing possible in any number from 2 to 50 and in certain numbers up to 380.

SSP47MSSP66MSSP510MSSP612M

Page 26: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

MANUAL CHUCKS

CHUCKS FOR PRODUCTION MACHINING, EDM AND WIRECUT EDM

HM 80ECHUCK FOR MILLING

HL- 110ECHUCK FOR LATHE & MILLING

HW- 128ECHUCK FOR WIRECUT EDM & MILLING

HE- 65ECHUCK FOR EDM

QUICK MANUAL CHUCKS

PNEUMATIC CHUCKS

Ask us for more details on CGM Products or visit www.cgmchuck.com

ELECTRODE / WORKPIECE HOLDERS AND WIRECUT EDM ACCESSORIES

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

FOR TOOL / DIE MAKING AND PRODUCTION

2µm REPEAT POSITIONING ACCURACY

• • • • • WORKPIECE FIXTURING MAKING ELECTRODES EDM SINKING WIRECUT EDMING MEASURING

QL-110ECHUCK FOR LATHE & MILLING

QW-128ECHUCK FOR WIRECUT & MILLING

QE-84ECHUCK FOR EDM & MILLING

QE-88ECHUCK FOR EDM & MILLING

AE-88ECHUCK FOR EDM & MILLING

AE-88EWCHUCK FOR EDM & MILLING

AM-138EPCCHUCK FOR MILLING

ELECTRODE ADJUSTING

HEAD

ELECTRODE /WORKPIECE HOLDERS

DRAWBARS

WIRECUT EDM WORKHOLDERS

STAINLESSSTEEL

26

Page 27: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

MANUAL CHUCKS

CHUCKS FOR PRODUCTION MACHINING, EDM AND WIRECUT EDM

HM 80ECHUCK FOR MILLING

HL- 110ECHUCK FOR LATHE & MILLING

HW- 128ECHUCK FOR WIRECUT EDM & MILLING

HE- 65ECHUCK FOR EDM

QUICK MANUAL CHUCKS

PNEUMATIC CHUCKS

Ask us for more details on CGM Products or visit www.cgmchuck.com

ELECTRODE / WORKPIECE HOLDERS AND WIRECUT EDM ACCESSORIES

MARKETED IN INDIA BY ABBOTT TOOLFAST PVT. LTD.

FOR TOOL / DIE MAKING AND PRODUCTION

2µm REPEAT POSITIONING ACCURACY

• • • • • WORKPIECE FIXTURING MAKING ELECTRODES EDM SINKING WIRECUT EDMING MEASURING

QL-110ECHUCK FOR LATHE & MILLING

QW-128ECHUCK FOR WIRECUT & MILLING

QE-84ECHUCK FOR EDM & MILLING

QE-88ECHUCK FOR EDM & MILLING

AE-88ECHUCK FOR EDM & MILLING

AE-88EWCHUCK FOR EDM & MILLING

AM-138EPCCHUCK FOR MILLING

ELECTRODE ADJUSTING

HEAD

ELECTRODE /WORKPIECE HOLDERS

DRAWBARS

WIRECUT EDM WORKHOLDERS

STAINLESSSTEEL

26

Page 28: Clamping Devices, Clamping Elementsjuzerengineering.com/wp-content/uploads/2017/11/... · Clamping Devices, Clamping Elements All Products Catalogue 2016 Chucks for Production Machining

Apart from our worldwide customers,

these and many more in India are among

USERS OF PRODUCTS

Plot No. 16, Sector-27A, Faridabad - 121003, Haryana, IndiaPh.: +91-129-4042237, 4133981, 4133982, 4133983Email: [email protected], [email protected]: www.toolfastclamps.com

Distributor: