CIVIL WORKS BILL OF QUANTITY
-
Upload
bhadani-qsandtraining -
Category
Documents
-
view
230 -
download
0
Transcript of CIVIL WORKS BILL OF QUANTITY
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
1/59
S.No. Particulars (1A) (1B) (1C)
SR CPWD NSR
1 Civil : ₹
2 Plumbing : ₹
3 Electrical : ₹
GRAND TOTAL
Engineering Projects (India) Limited
BPA Site,Rajgir
SUMMARY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
2/59
S.No. Description Unit Qty Rate Amount
SUB-HEAD : I : EARTH WORK 1 Earth work in excavation in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on
plan) including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out the
excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
All Kind of soil Cum. 850
2 Earth work in excavation over areas (exceeding 30 cm in depth 1.5 m in width as well as 10 sqm on
plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m disposed earth to be
levelled and neatly dressed.
All Kind of soil Cum. 0
3 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers
not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead.
Cum. 3402
4 Excavating trenches of required width for pipes cables etc, including excavation for sockets, and
dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and
then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each
deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a
lead of 50 m.
All kinds of soil.
Pipes, cables etc. exceeding 80mm dia. But not exceeding 300mm dia. Mtr. 62
5 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth
upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of
50m outside the periphery of the area cleared. 100 Sqm. 4315
6 Supplying and Fil ling in plinth with local sand and under floors including, watering, ramming
consolidating and dressing complete. Cum. 3348
Engineering Projects (I) limited
BPA Site,Rajgir
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
BILL OF QUANTITY FOR PACKAGE B
Civil 1A
Page 1
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
3/59
7 Supplying chemical emulsion in sealed containers including delivery as specified.
Chlorphyriphos/Lindone emulsifiable concretrate of 20%. Litre 8060
8 Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termits treatment
(including the cost of chemical emulsion)
9 Along external wall where the apron is not provided using chemical imulsion @ 7.5 liters/sqm of the
vertical surface of the substructure to a depth of 300mm including excavation channel along the wall &
rodding etc. complete.
With chlorphyriphos/Lindone E.C. 20% with 1% concentration Mtr. 706
10 Along the external wall below concrete or masonry apron using chemical emulsion @ 2.55 litres per
linear metre including drilling and plugging holes etc.
With chlorphyriphos E.C. 20% with 1% concentration Mtr. 666
11 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart
including drilling and plugging 12mm diameter holes with cement mortar 1:2 (1 cement : 2 coarse
sand) to match the existing floor.
With chlorphyriphos E.C. 20% with 1% concentration Sqm. 5565
12 Treatment of existing masonry using chemical emulsion @ one litre per hole, 300mm interval
including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse
sand) to the full depth of the hole.
With chlorphyriphos E.C. 20% with 1% concentration Mtr. 490
SUB-HEAD : II : CONCRETE WORK
13 Providing and laying in position cement concrete of specified grade excluding the cost of centring,
shuttering, all work upto plinth level.
1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (Part-
I) Cum. 635
14 Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20mm nominal size).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)Sqm 415
Page 2
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
4/59
15 Extra for providing and mixing waterproofing material in cement concrete work in proportion
recommended by the manufacturers.
Per bag of
50 Kg. of
cement. 167
16 Applying a coat of required petroleum bitumen of penetration 80/100 of approved quality using
1.7kg/m2
on damp proof course after cleaning the surface with brushing and finally with a piece of cloth
lighting, soaked in kerosene oil.
Sqm 415
17 Providing and laying cement concrete internal walls, return walls, walls (any thickness) includingattached Plasters, Colume, Piers, Abutments, Pilars, Post, Structs, buttresses, string or lacing courses,
parapets coping, bedblocks, anchor blocking, plin window sills, fills etc. up to floor five level excluding
the cast of centring shuttering and finishing 1:11/2:3 ( 1 : Cement : 1 1/2 Coarse Sand : 3 grades tone
aggregate 20,, nominal size.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (Part-
I)Cum. 33
18 Providing and laying in position machine batched, machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced cement concrete structural elements, excluding the
cost of centring, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete.(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (Part-
I)
All work upto plinth levelCum. 197
Walls columns, pillars, posts and struts etc.Cum. 556
Beams, Plinth beams, griders, bressumers, contilevers, Suspended floors lintels roofs and staircases
including spiral staircases, shelves etc. Cum. 1842
19 Add or deduct for providing richer or leaner mixer respectively at all floor levels.
Providing M-25 grade R.C.C. instead of M-20 grade R.C.C.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (Part-
I)Cum. 2425
20 Providing M-30 grade R.C.C. instead of M-20 grade R.C.C.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (Part-
I)Cum. 170
Page 3
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
5/59
21 Centring and shuttering including strutting, propping etc. And removal of form for.
Foundations, footings, bases of columns etc. for mass concrete.Sqm 702
Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.Sqm 2047
Suspended floors, roofs, landings, balcnies and access platform.Sqm 4392
Shelves (Cast in situ)Sqm 262
Lintels, beams, plinth beams, griders, bressumers and cantilevers.Sqm 4046
Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 5865
Stairs, (excluding landings) except spiral-staircases.Sqm 1688
Archies Domes, Vaults upto 6 m spanSqm 50
Extra for Archies, Domes, Vaults exceeds 6 m spanSqm 12
22 Vertical and Horizontal lines fins individually or framing box louverd Band, faces and Eaves Board. Sqm 53
23 Small lintels not exceeding 1.5m clear span, mouldings as in cornices, window sills, string, courses,
bands, copings, bed plates, anchor blocks and the like.
Sqm 164
24 Extra for Shuttering in circular work (20% of respective catering and shuttering items)
Slab Sqm 800
Beam Sqm 640
Column Sqm 870
25 Edges of slabs and breaks in floors and walls.
Under 20 cms wideMtr. 1224
26 Weather shade, Chajja, Carpets etc including edge. Sqm 220
27 Add or deduct for plaster drip course /groove in plastered surface or moulding to R.C.C. projections.
Mtr. 68
28 Extra for additional height in centring, shuttering where requirement with adequate bracing propping
etc. including cast of de-shutter and de-centring at all levels, over a height of 3.5m for every additional
height of 1 metre or part thereof suspended floor, roof landing beams and balconies (plain area to be
measured).Sqm 3730
Page 4
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
6/59
29 Providing, precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 6mm
nominal size) reinforced with 1.6 mm dia mild steel wire including roughening cleaning, fixing and
finishing in cement mortar 1:3 (1 cement : 3 fine sand ) etc. complete excluding plastering of the
jambs, sills and soffits.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
50 mm thick Sqm 52
30 Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding
all complete.
Thermo -Mechanically treated Bar TMT FE-500 (For Conference cum welfare centre+UGT)
Kg. 181380
Thermo -Mechanically Treated bars(TMTC-500)8 mm dia bars(Other than Conference cum
welfare centre)
Kg.
55090
Thermo -Mechanically Treated bars(TMTC-500)10 mm dia bars(Other than Conference cum
welfare centre)
Kg.
30235
Thermo -Mechanically treated Bar TMT FE-500 12 to 32 mm(Other than Conference cum welfare
centre) Kg. 111775
31 Providing and fixing in position copper plate as per design for expansion joints.Kg. 0
32 Providing and filling in position, blown bitumen in expansion joints.100mLx1c
m
Wx1cmD 25
33 Providing and filling in position bitumen mix filler of Proportion 80 kg of hot bitumen, 1 kg of cement
and 0.25 cubic metre of coarse sand for expansion joints
100mLx1c
m
Wx1cmD 0
34 Providing and fixing in position 12 mm thick bitumen imregnated fibre board conforming to IS: 1838
including cost of primer, sealing compound in expansion joints. 100mLx1
cmD 0
35 Providing and fixing sheet covering over expansion joints with iron screws as per design to match the
colour/shade of wall treatment.
Asbestos sheet 6 mm thick
150 mm wideMtr. 0
200 mm wideMtr. 0
Page 5
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
7/59
Aluminium Fluted Strip 3.15 mm thick
150 mm wide.Mtr. 0
200 mm wideMtr. 0
SUB HEAD : III : BRICK WORK(Fly-Ash)
36 Brick work with bricks(fly-ash) of class designation 100 A in foundation and plinth in
Cement mortar 1:6 (1 cement : 6 coarse sand).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)Cum. 2527
37 Extra for Brick work in superstructure above plinth level upto floor V level. Cum. 1985
38 Half brick masonry with bricks of class designation 100 A in foundations and plinth in :
Cement mortar 1:4 (1 cement : 4 coarse sand).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm 1175
Extra for half Brick masonry in superstructure above plinth level upto floor V level
Sqm 1175
39 Extra for providing and placing in portion 2 Nos. 6mm dia M.S bars at every third course of half brick
masonary. Sqm 1175
SUB HEAD : IV : MARBLE WORK
40 Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters
facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick
base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixe with
matching pigament-epoxy touch ups including rubbing, curing etc. complete at all levels.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Area of each slab over 0.2 sqm but upto 0.5 sqm Rajnagar plain white. Sqm 0
Area of each slab over 0.2 sqm but upto 0.5 sqm Granite of any colour and shade Sqm 3554
41 Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. over item no. 8.2
including machine polishing to edge to give high gloss finish etc. complete as per design approved by
Engineer-in-charge.
Marble work Mtr. 5
Granite work Mtr. 466Page 6
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
8/59
42 Extra for fixing marble/granite stone over and above corresponding basic item, in facia and drops of
width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc.
complete. Mtr. 146
43 Extra for providing opening of required size & shape for wash basins/kitchen sink in Kitchen platform.
Vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc.
including rubing and polishing of cut edges etc.complete. Each 67
44 Mirror polishing on marble work/stone work where ever required to given high gloss finish complete.
Sqm 0
45 Marble work gang saw cut (Polished and machine cut) of thickness 18 mm for wall lining (Veener
work) in cement mortor 1:3 (1 Cement : 3 Coarse sand) including pointing with white cement motor 1:2
(1 White cement : 2 Marble Dust) with and mixture of pigment to match the marble shade (To be
secural to the backing of means of cramps, which shall be paid for seperating) Note:- Used PPC
Cement to be used conforming to IS: 1489 (Part-I)
White Marble - Raj Nagar Plain , Udaipur Green Marble / Zebra Black Marble - area of each slab over
upto 0.50 sqm. Sqm 102
46 Providing and fixing expansion hold fastners on CC / RCC / Brick Surface backing including drillingnecessary holes and the cost of bolts etc complete.
Fastner with threaded dia 12mmEach 120
47 Providing and fixing stone jaali 40 mm thick throughout (without sunking or moulding in jali slab ) in
cement mortar 1:3 (1 cement : 3 coarse sand ) includng pointing in white cement mortar 1:2 (1 white
cement : 2 stone dust) with an admixture of pigment , matching the stone shade , jali slab without any
chamfers etc.
White sand stone Sqm5.76
SUB HEAD : V : WOOD WORK
48 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought
framed and fixed in position:
Second Class teakwood Cum. 0
49 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory
windows including black enamelled M.S. but hinges with necessary screws excluding. Panelling which
will be paid for separately.
35 mm thick Second Class teakwood Sqm 0 Page 7
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
9/59
50 Providing and fixing panelling or panelling and glazing in panelled of panelled and glazed shutters for
doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside
grooves or rebates to be measured) panelling for panelled or panelled and glazed shutters 25mm to
40mm thick.
Second class teak woodSqm 0
51 Providing and fixing flush door shutters non decorative type, core of block board construction with
frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands
and face veneers on both faces of shutters:
35 mm thick including anodised aluminium but hinges with necessary screws.Sqm 465
52 Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of
shutters (over all area of door shutter to be measured). Sqm 455
53 Extra for cutting rebate in flush door shutters (total area of the shutter to be measured). Sqm 112
54 Providing and fixing 35 mm thick wire gauze shutters using galvanised M.S. wire gauze of average
width of aperture 1.4mm with wire of dia. 0.63 mm for doors windows and clerestory windows
including bright finished or/and black enamelled M.S. Butt Hinges with necessary screws.
Second class teak wood. Sqm 22
55 Extra for Providing and Fixing Flush Door Shutter 1mm thick laminate of approved shade - Both side
of shutter. Sqm 463
56 Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg/square
meter (4 mm thick) glass panels including black enamelled M.S. Butt hinges with necessary screws.
35 mm thick Second class teak wood.
Sqm 6
57 Providing and fixing M.S. Grills of requirement pattern in frames of window etc. with M.S. flats square
or round bars etc. all complete.
Fixed to steel window by welding.Kg. 1308
58 Providing and fixing fly proof galvanised M.S. wire gauze to windows and clerestory window using
galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia.
0.63 mm.
With second class teak wood beading 62x19 mmSqm 0
Page 8
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
10/59
59 Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts,
nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix (1cement : 3
coarse sand : 6 graded stone aggregate 20mm nominal size). Note:- Used PPC Cement to be used
conforming to IS: 1489 (Part-I)
Each 150
60 Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than
grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with, nuts and screws
etc. complete.
250x16 mmEach 213
61 Providing and fixing aluminium tower bolts anodised (anodic coating not less than grade AC 10 as per
IS: 1868) transparent or dyed to required colour and shade with, nuts and screws etc. complete.
300x10 mm Each 236
150x10 mm Each 138
100x10 mm Each 44
62 Providing and fixing aluminium pull bolt lock anodised (anodic coating not less than grade AC 10 as
per IS: 1868) transparent or dyed to required colour and shade with, nuts and screws etc. complete.
Each 1215
63 Providing and fixing aluminium handles anodised (anodic coating not less than grade AC 10 as per IS:
1868) transparent or dyed to required colour and shade with, nuts and screws etc. complete.
125 mmEach 251
100 mmEach 236
64 Providing and fixing aluminium hanging floor door stopper anodised (anodic coating not less than
grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with, necessary screws
etc. complete.
Single rubber stopper Each 0
Twin rubber stopper Each 228
65 Deduct if fixed shutters (without hinges) are provided instead of openable shutters for doors, windows
or cleresory windows with:
Black enamelled M.S Butt hinges with necessary screws.Sqm 0
66 Extra for Providing and fixing flush door with teak veneering.Page 9
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
11/59
On one side Sqm 174
SUB HEAD : VI : STEEL WORKS
67 Providing and fixing 1mm thick M.S sheet door with frame of 40x40x6mm angle iron and 3mm M.S
gusset plates at the junction and corners, all necessary fittings complete including applying priming
coat of approved steel primer.
Using flat 30x6mm for diagonal braces and central cross piece.Sqm 191
68 Supplying and fixing rolling shutters of approved make, made of required size of M.S laths interlocked
together through their entire length and jointed together at the end by end locks mounted on specially
designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with
push and pull operation complete including the cost of providing an fixing necessary 27.5 cm long wire
springs grade No. 2 and M.S top cover of required thickness for rolling shutters.
80x1.25mm M.S Laths with 1.25mm thick top cover.Sqm. 80
Providing and fixing ball bearing for rolling shutters.Each 9
69 Extra for providing mechanical device chain and crank operation for operating rolling shutters.
Exceeding 10.00 sqm and upto 16.80 sqm in area (say average 14 sqm) Sqm. 80
70 Extra for providing grilled rolling shutters. Sqm. 63
71 Providing and fixing T-iron frames for doors windows and ventilators of mils steel Tee-Sections, joints
miltred and welded with 15x3 mm lugs 10 cm long embedded in cement concrete blocks 15x10x10 cm
of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden
plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required
including.Kg. 5687
Page 10
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
12/59
72 Providing and fixing pressed steel door conforming IS code 351 manufactured from commercial mild
steel sheet of 1.25mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold
of mild steel angle of section 50x25 mm or base ties of 1.25mm pressed mild steel welded or rigidy
fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt
hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying
a coat of approved steel primer after pre-teatement of the surface as directed by Engineer-in-charge
Profile BMtr. 5
Profile CMtr. 1462
Profile EMtr. 140
73 Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including
applying a priming coat of approved steel primer.
E.R.W. tube 40 mm nominal diaKg. 510
73-A Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints
mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks
15x10x10 cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or
with woodenplugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts asrequired, including providng and fixing of glass panes with glazing clips and special metal-sash putty of
approved make complete including applying a priming coat of approved steel primer; excluding the
cost of metal beading and other fitting except necessary hinges or pivots as required. Note:- Used PPC
Cement to be used conforming to IS: 1489 (Part-I)
Doors Sqm. 211
73-B Extra for providing and fixing steel beading of approved shape and section with screws instread of
glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units.
Steel Doors Sqm. 13Steel Windows Sqm. 196
74 Structural Steel work riveted or bolted in rolled section, builtup sections, plate and inserts, trussess
and frame work, including cutting, hoisting, fixing in position and applying a prime coat of approved
steel primer etc. all complete. Kg. 88630
Page 11
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
13/59
76 Fencing with welded steel wire fabric 75 mm x 50 mm providing 1.2M high fencing with Angle Iron
post 50m x 50m x 6mm at 3 meter centre to centre with 0.4m embedded in M-15 Grade cement
concrete, corner end and every 10th Post to be strutted, provided with welded steel wire fabric of 75 x
50 mm or 75 x 25 mm mesh and fixed to ironpost by flat iron 50 x 5mm and bolted etc all complete.
Mt. 82
SUB-HEAD : VII : FLOORING
80 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate) finished with a
floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc.complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
40mm thick with 20mm nominal size stone aggregate. Sqm. 1605
81 Cement plaster skirting (upto 30 cm height) with cement mortar 1:3 (1 cement : 3 coarse sand) finished
with a floating coat of neat cement.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
18 mm thick Sqm. 232
82 Providing and laying Ist quality Ceramic glazed wall tiles confirming to IS : 15622 (thickness to be
specified by manufacturer) of approved make in all colours, shades except burgundy, bottle green ,
black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm
thick bed of Cement Mortar 1:3 (1 Cement : 3 Coarse sand ) and jointing with grey cement slurry @
3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 1050
83 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 15622 of approved make in colours such as white, ivory,Grey, Fume Red, Brown, laid on 20 mm thick Cement motar 1:4 ( 1 cement : 4 coarse sand) including
pointing the joints with white cement and matching pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 890
Page 12
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
14/59
84 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 15622 of approved make in colours such shades except
white, ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cement motar 1:4 ( 1 cement : 4 coarse
sand) including pointing the joints with white cement and matching pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)Sqm. 0
85 Providing and fixing glass strips in joint of terrazo/cement concrete floors.
40 mm wide 4 mm thick Mtr.1150
86 Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or
equivalent make in colours such as white, ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cement
motar 1:4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching
pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)Sqm. 1196
87 Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the
manufacturer) of lst quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or
equivalent make in colours such as white, ivory, Grey, Fume Red, Brown, laid on 20 mm thick Cementmotar 1:4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching
pigment etc. complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)Sqm. 918
88 Providing and laying vitrifed floor tiles skirting (thickness to be specified by the manufacturer) with
water absorption's less than 0.08% and conforming to IS: 15622 of approved make in all colours and
shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints
with white cement and matching pigments etc, complete. (Flooring and Skirting)
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Size of Tile 60x60 cm Sqm. 374
89 Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-
in-charge) over 20 mm (average) thick base of Cement motar 1:4 ( 1 cement : 4 coarse sand) laid and
jointed with grey cement slurry including rubbing and polishing complete with.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Rajnagar plain white marble 18mm thick above 0.10 sqm upto 0.20 sqm.Sqm. 30
Udaipur Green MarbleSqm. 32
Page 13
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
15/59
90 Tile workin skirting, risers of stepsanddado over 12 mmthick bed of cement mortar 1:3 (1cement : 3
coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement
mixed with pigment of matching shade complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Marble tiles (polished) Raj Nagar 8 mm thick Sqm. 0
91 Kota stone slab flooring over 20 mm (Av.) thick base laid over and jointed with grey cement slurry
mixed with pigment to match the shade of the slab including rubbing and polishing complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
25mm thick. Sqm. 830
92 Kota stone slab 25mmthickin riser ofsteps, skirting, dado and pillars laid on 12mm(Av.) thick cement
mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match
the shade of the slab including rubbing and polishing complete
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I) Sqm. 422
93 Extra for nosing in marble stone for treads Mtr. 25
94 Extra for Marble stone flooring in treads of steps. Not Exceeding 30 cm in width. Sqm. 615
95 Extra for nosing in steps and treads of kota stone slab Mtr. 740
96 Extra for kota stone floooring in steps and trades not exceeding 30 cm in width. Sqm. 484
SUB-HEAD : VIII : ROOFING
99 Providing gola 75x75mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm
and down gauge) including finishing with cement mortar 1:3(1 cement : 3 coarse sand) as per standard
design.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I) Rmt. 671
100 Making khurras 45 x 45 cm with average minimum thickness of 5cm cement concrete 1:2:4 (1 cement
: 2 coarse sand : 4 graded stone aggregate of 20mm nominal size) over PVC sheet 1m x 1m x 400
micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement
rounding the edges and making and finishing the outlet complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Each 57
SUB-HEAD : IX : FINISHING Page 14
101 12 l f i
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
16/59
101 12mm cement plaster of mix
1:6 (1 cement : 6 coarse sand) Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 4334
102 15 mm cement plaster on rough side of single or half brick wall of mix.
1:6 (1 cement : 6 coarse sand) Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 4505
103 20mm cement plaster of mix
1:4 (1 cement : 4 coarse sand) Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 6330
104 6mm cement plaster to ceiling of mix
1:4 (1 cement : 4 coarse sand) Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 5520
105 White washing with whiting to given an even shade:
New work (three or more goats)Sqm. 5420
106 Distempering with oil bound washable distemper of approved brand and manufacture to give an even
shade.
New work (two or more coats) over and incluidng priming coat with cement primer.Sqm. 435
107 Distemperig with 1st quality washable distemper (ready made) of approved manufacturer and of
required shade and colour complete. As per manufacture's specifications.
Two or more coats on new work.Sqm. 735
108 Applying one coat of cement primer of approved brand and manufacture on wall surface.
Cement Primer Sqm. 830
Distemper Primer Sqm. 735
109 Finishing walls with water proofing cement paint of approved brand and manufacture and of required
shade to give an even shade.
New work (three or more coats)Sqm. 780
110 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Page 15
T t k
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
17/59
Two or more coats on new work Sqm. 300
114 Painting with synthetic enamel paint of approved brand and manufacture of required colour to given an
even shade:
115 Two or more coats on new work over an under coat of suitable shade with ordinary pain of approved
brand and manufacture. Sqm. 7161
116 French Sprit Polishing two or more coats on wood work including a coat of wood filler. Sqm. 460
119 Tiles brick masonry work 5 cm thick with the bricks of class designation 100 A in cement mortor 1:3 (
1 cement : 3 coarse sand) in superstructure.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I) Sqm. 45
120 Pointing on tile brick work with cement mortor 1: 3 (1 cement : 3 coarse sand ) Flush Pointing.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I) Sqm. 135
SUB-HEAD : X : ALUMINIMUM WORK
122 Providing and fixing anodised aluminum work for doors, windows, ventilators and partitions with
extruded built up standard tubular and other sections of approved make conforming to IS: 733 and IS:
1285 anodised transparent or dyed to required shade according to IS: 1868. (Minimum anodise coating
of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners
including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene
felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically
wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P.
brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in
Charge.(Glazing and panelling to be paid for separately.)
For fixed portion.Kg. 3490
124 Providing and fixing stainless steel (SS 304 Grade) adjustable friction window stays of approvedquality with necessary stainless Steel Screws etc. to the side hung window as per diection of Engineer-
in-Charge-355x19mm. Each 263
125 Providing and fixing 12 mm thick prelaminated three layermedium density (exterior grade) particle
board Grade I, Type II conforming to IS:12823 bonded with phenol formaidhyde synthetic resin, of
approved brand and manufacture in panelling fixed in aluminium doors, window shutters and partition
frames, with C.P. brass/stainless steel screws etc. complete as per architectural drawings and direction
of engineer-in-charge.
Pre-laminated particle board with decorative lamination on one side and balancing lamination of S m. 25
Page 16
Prelaminated particle board with decorative finish on both side
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
18/59
Prelaminated particle board with decorative finish on both side.Sqm. 155
0
126 Providing and fixing glazing in aluminium door, window, ventilator, shutters and partitions etc. with
PVC/Neo Prene gasket etc. complete as per the architectural drawings and the directions of Engineer-
in-Charge. (Cost of aluminium snap beading shall be paid in basic item)
With glass panes of 4.0 mm thickness (weight not less than 10.0kg/sqm.)Sqm. 5
With glass panes of 5.50 mm thickness (weight not less than 13.75kg/sqm.)Sqm. 595
127 Providing and fixing double action hydraulic floor spring of approved brand and manufacture(conforming to IS:6315), for Aluminium doors including cost of cutting floor as required, embedding in
floors and cover plates etc. complete as per direction of Engineer-in-Charge. Each 25
SUB-HEAD : XI : WATER PROOFING
130 Providing and laying integral cement based water proofing treatment including prepatation of surface as
required for treatment of roofs, balconies, terraces etc, consisting of following operations a) Applying
and grouting a slurry coat of neat cement using 2.75kg/sqm of cement admixed with proprietary water
proofing compound cleaning the surface before treatment, b) Laying cement concrete using broken
bricks/ bricks bats 25 mm to 100mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand)
admixed with proprietary water proofing compound conforming to IS: 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with proprietary water proofing
compound conforming to IS : 2545 to required slope and treating similary the adjoining walls upto 300
mm height including rounding of junctions, or walls and slabs.
With average thickness of 120mm and minimum thickness at khurras as 65mm. Note:- Used PPC
Cement to be used conforming to IS: 1489 (Part-I) Sqm. 3115
SUB-HEAD : XII : PILING WORK
135 Boring, providing and installing cast in situ single under reamed piles of specified diameter and length
below pile cap in cement concrete piles with mix 1:1.5::3 (1 cement : 11/2 coarse sand: 3 graded stoneaggregate 20 mm nominal size) to carry a safe working load not less than specified, excluding the cost
of steel reinfrement but including the cost of boring with bentonite solution and the length of the pile to
be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured up to the
bottom of pile cap). (Note:- Ready Mix Concrete (RMC) using PPC Cement to be used
confirming to IS : 1489 (Part-I)
300 mm dia piles. meter 70
400 mm dia piles. meter 150
Page 17
136 Extra over item no 1 for boring providing and installing cast in situ double under reamed piles instead
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
19/59
136 Extra over item no. 1 for boring, providing and installing cast in situ double under reamed piles, instead
of single under ream of specified diameter and length. (Only the quantity of extra bulbs are to be paid).
Each 90
137 Vertical load testing of pile in accordance with IS:2911 (Part-IV) including installation of loading
platform and preparation of pile head or construction of test cap and dismantling of test cap after test
etc. complete as per specification & the direction of Engineer-in-Charge.
Single Pile
Upto 50 tonne capacity pile cost per test per test 2
Above 50 tonne & upto 100 tonne capacity pile per test 10
138 Cyclic vertical load testing of pile in accordance with IS Code of practice IS : 2911 (Part-IV) including
preparation of pile head etc. for :-
Page 18
Single pile
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
20/59
Single pile
Upto 50 tonne capacity pile per test 2
Group of two pile
Upto 50 tonne capacity each per test 10
139 Lateral load testing of single pile in accordance with I.S. Code of practice I.S. : 2911 (Part-IV) for
determining safe allowable lateral load on pile :
Upto 50 tonne capacity pile per test 2
140 Reinforcement for RCC work including straightening, cutting, bending, placing in position and bindingetc. all complete.
Thermo-mechanically treated bar TMT FE-415 Kg 125100
141 Demolishing RCC work including stacking of steel bars and disposal of unserviceable material with 50
meter lead. Cum 60
142 Providing and laying in position machine batched, machine mixed and machine vibrated design mix
cement concrete of specified grade for reinforced cement concrete structural elements, excluding the
cost of centring, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete.
(Note:- Ready Mix Concrete (RMC) using PPC Cement to be used confirming to IS : 1489 (Part-
I)
All work upto plinth level Cum. 670
143 Centring and shuttering including strutting, propping etc. And removal of form for.
Foundations, footings, bases of columns etc. for mass concrete.Sqm 850
Lintels, beams, plinth bams, griders, bressumers and cantilevers.Sqm 485
144 Add or deduct for providing richer or leaner mixer respectively at all floor levels.
Providing M-25 grade R.C.C. instead of M-20 grade R.C.C. (Note:- Ready Mix Concrete (RMC)using PPC Cement to be used confirming to IS : 1489 (Part-I) Cum. 670
145 Building Carriage
A Bricks 1000nos. 1321
B Aggregate Cum 4068
C Coarse Sand Cum 2916
D Local Sand Cum 3348
Total Page 19
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
21/59
Sl. No. Description Unit Qty Rate Amount
SUB-HEAD : I : EARTH WORK
1 Providing and Laying soiling not exceeding 175mm of compacted thickens using 2.42
cubic meter of stone aggregate 22.5 to 53m size range with necessary screening, blinding
material, murrum and selected earth for every 10 Sqm. Of area including sorting, spreading
as shown in the drawing, watering and consolidation with compactor etc. complete
including supplying, spreading and consolidation of screening and blinding material etc.
complete. (Measurement for payment shall be on final compacted thickness of the layers as
mentioned in the drawings). No separate payment of the screening and blinding materialshall be taken for payment.
175m thick consolidated thickness in one layer (using 0.53 cum,. Of stone screening
13.2mm nominal size and 0.18cum. Of blinding material murrum / selected earth for every
10 sqm.)-For Conference Cum Welfare Centre Cum 435
175m thick consolidated thickness in one layer (using 0.53 cum,. Of stone screening
13.2mm nominal size and 0.18cum. Of blinding material murrum / selected earth for every
10 sqm.)-All buildings except CCWCCum 474.86
SUB-HEAD : II : CONCRETE WORK 2 Making Plinth Protection 50 mm thick of cement concrete 1:3:6 (1: Cement : 3 Coarse
Sand : 6 Graded Stone aggregate 20mm nominal size) over 75 mmbed by dry brick ballast
40mm nominal size well rammed and consolidated and grouted with fine sand including
finishing the top smooth.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I) Sqm 606
Engineering Projects (I) limited
BPA Site,Rajgir
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Civil 1B
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
22/59
Sl. No. Description Unit Qty Rate Amount
3 Brick edging 7 cm width 11.4 cm deep to plinth protection with bricks of class
designation 75 including grouting with cement mortor 1 : 4 ( 1: Cement : 4 Fine sand)
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I) Meter 959
SUB HEAD : III : BRICK WORK
SUB HEAD : IV : MARBLE WORK
SUB HEAD : V : WOOD WORK
4 Providing and fixing 100 mm brass lock (best make of approved quality) for aluminium
door including necessary Grass cutting and making good etc. complete.Each 97
SUB HEAD : VI : STEEL WORKS
5 Steel work welded in built up section / framed work including cutting, hoisting, fixing in
position and applying a primer coat of approved steel primer using structural steel etc as
required. in stringers, treads, landing etc of staircase including use of chequeral platewherever required, all complete.
Kg. 220
6 Providing and fixing precoated galvanised iron profile sheets (Size, shape and pitch of
corrugation as approved by Engineer-in-charge) 0.50 mm + 5% total coated thickness
(TCT) , Zinc coating 120 gsm as per IS : 277 in 240 mpa steel grade, 5-7 microns epoxy
primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have
protective guard film of 25 microns minimum to avoid scratches while transportation and
should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The
sheet shall be fixed using self drilling / self tapping screws of size (5.5 X 55 mm) with
EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with shitel lead
complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of
purlins, rafters and trusses and including cutting to size and shape wherever required.
Sqm 265
SUB-HEAD : VII : FLOORING
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
23/59
Sl. No. Description Unit Qty Rate Amount
SUB-HEAD : VIII : ROOFING
SUB-HEAD : IX : FINISHING
7 Finishing wall with Premium Acrylic smooth exterior paint with si licon addit ions of
required shade. New work (Two or more coats applied @ 1.43 Ltr / 10 sqm over and
include base coat of water proofing cement paint applied @ 2.20 kg/10sqm. Sqm. 7085
8 Melamine Polishing on wood work (one or more coat) Sqm. 275
SUB-HEAD : X : ALUMINIMUM WORK
9 For shutters of doors, windows and ventilators including providing and fixing hinges/pivots
and making provision for fixing of fittings wherever required including the cost of PVC
neoprene gasket required (Fittings shall be paid for separately). Kg. 790
10 Filling the gap in between aluminium frame and adjusment RCC/Brick/ Stone work by
Providing weather silicon sealed over backer rod of approved quality as per Architecturaldrawing and direction of Engineer-in-Charge.
Upto 5mm depth and 5 mm width. Rmt 430
11 Providing and fixing Double glazed hermetically sealed glazed in Aluminium window,
ventilator and portation etc. with 6 mm thick clear float glass both side having 12 mm air
gap including providing EPDM gasket, perforated aluminium spacers, desiccants, sealent
(Both Primary and Secondary sealent) etc as per specifications, drawings and direction of
Engineer-in-Charge complete. Sqm. 0
SUB-HEAD : XI : WATER PROOFINGSUB-HEAD : XII : PILING WORK
Total
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
24/59
Sl. No. Description Unit Qty Rate Amount
SUB-HEAD : I : EARTH WORK
SUB-HEAD : II : CONCRETE WORK
1 Extra for vacum dewatering method adopting "Tremix" system including finishing the
electrical floater etc all complete as directed by Engineer-in-charge. Sqm 70
SUB HEAD : III : BRICK WORK
SUB HEAD : IV : MARBLE WORK
SUB HEAD : V : WOOD WORK
SUB HEAD : VI : STEEL WORKS
2 Providing and fixing stainless steel hand rail 1.05m high in staircase made up of hand rail
size 63 mm dia 16G SS pipe welded to SS Bluster 40mm dia curved on shaped welded with
hand rail, Baluster shall be grouted and fixed to RCC passes, waste slab 1050 mm from
which six round pipe curved shape 12mm dia will be running and fixed with accessories S.Il
shoe in 100mm dia (SS 304 grade) complete. Rm 158
3 Providing and erecting 2mm thick profi led metal sheets from approved manufacturer
including securing firmly by fastening with substrate to receive concrete (concrete to be paid
separately) complete as per manufacturer's specifications and as directed (Plan area to bemeasured, for payment) rates to include two or more coats of synthetic enamel paint over a
coat of zinc chromate steel primer on the exposed sides of sheeting etc. all complete at all
height and depth. Sqm. 23
Engineering Projects (I) limited
BPA Site,Rajgir
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Civil 1C
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
25/59
Sl. No. Description Unit Qty Rate Amount
4 Supply & installation of TATA Blue Scope or approved equivalent make Double skin
insulated Roofing / cladding system comprising of HI-RIB profiled Factory finished
External and internal sheets manufactured out of 0.5mm TCT (Total coated thickness)
silicone modified polyster (SMP) coated Hi-Tensil Galvolume Steel (AZ-150 GSM
Zinc/Aluminium alloy coating total of both sides as per AS 1397) having 550Mpa Yield
strenght. The weathering surface to be Given a finish coat nominal 5 micron. The sheets
shall have 1000 mm cover width, 28mm high crests at 250 mm wide pan with specialMale/Female side laps and anti-siphoning feature to prevent leakges. The pan shall be
stiffenered by using 3 small ribs. The inner sheet shall be RMP coated galvanised steel
(Z180 GSM zinc coating/275 Mpa Steel) in similar dimenions/size and fixed to the structure
(by others) by means oif corrosion protecitons self drilling sefl tapping fasteners. The Sub-
girts of size 50mm x 50mm x manufactured out of 1.6 G.I. . G.I "Z" shape would be fixed
with similar scres (12-14x15) on to surface.
All insulation of 50 mm thick glasswool of density 24 Kgs wrapped in clear polythene
sheets shall be fixed in the cavity between two sheets. The sheets shall be supplied in custom
lengths and for a maximum up to 12 mts.Sqm 1260
SUB-HEAD : VII : FLOORING
5 Extra for laying floors in pattern with combination of granite / marble/virtif ied tile/ Kota
Stone or else etc. all complete as direction in Engineer-in-Charge.Sqm. 185
6 Providing and fixing50 x 50mm thick of glass mosaic tile inall the shape and size thickness
as per manufacturer specification at all depth and height of approved colour and shade over a
bed of cement mortar 1:2 (1 cement : 2 coarse sand) jointed with white cement slurry mixed
with pigment to match the sahde of glass mosaic tile or fixed with chemical adhesive as per
recommendation by Manufacturer. All work to be carried out as per drawing.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 140
SUB-HEAD : VIII : ROOFING
SUB-HEAD : IX : FINISHING
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
26/59
Sl. No. Description Unit Qty Rate Amount
7 Providing and applying two or more of water base enamel paint toall internal area with base
coat at all height and depth etc all complete as per the direction Engineer-in-Charge. (water
base enamal paint to meet low VOC criteria as specified by GRIHA)(For CCWC)
Sqm. 3850
8 Providing and applying two or more of water base enamel paint toall internal area with base
coat at all height and depth etc all complete as per the direction Engineer-in-Charge. (waterbase enamal paint to meet low VOC criteria as specified by GRIHA)(All buildings
except CCWC)
Sqm. 4525
9 Providing and applying external paint of approved brand and manufacture equvalent to M/s
SKK make at all height & depth etc all complete as directed by Engineer-in-Charge (Basic
coat of Rs. 25/- sft included base coat)Sqm. 2025
10 25 mm cement plaster in cement mortor 1:4 (1 Cement : 4 coarse sand) including Providing
Chicken mess etc all complete.
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm. 100
11 Providing and applying two or more coats of colour less silicon paint at all Locations
Prepared and applied as manufacture specifications Including appropriate Prime coat,
preparation of surface etc. all complete as directed by Engineer-in-Charge.Sqm. 68
SUB-HEAD : X : ALUMINIMUM WORK
SUB-HEAD : XI : WATER PROOFING
12 Providing and laying Zentrifix Elastic Flexible membrane coating consisting of Zentrifix
Elastic Powder (1 kg/bag) and Emcefle-15 Liquid (0.5 kgs/bag) consumption for wet areashall be minimum 3 kgs/sqm or 1.7 kgs/sqm/mm thickness complete as manufactured by
M.C. Bauchmie (I) or approved equivalent as per Architect's direction.Sqm 180
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
27/59
Sl. No. Description Unit Qty Rate Amount
13 Providing and laying polymer modified concrete screed 25mm thick using 8mm down
aggregate in 1:1:3 (1 cement:1 aggregate:3 coarse sand admixed with special
DICHATMENT DM-0.5% by weight of cement, NAFUFIL SBR-5% by weight of cement)
complete manufactured by M.C. Bauchemie or approved equivalent as per Architect's
direction. Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Sqm 138
14 Providing and laying MECEKRETE or approved equivalent non shrink grout of size
30x30mm completeR.M. 161
Note:
All additional openings made in and around RCC slab for sanitary pipes shall have to be
sealed, grouted and made water tight before commencing on the above works and above
treatment shall be carried out through a specialized approved agency.
15 Providing and applying 50mm thick polyurethane rigid foam sprayed in situ by automatically
and mechanised system with density of 40 Kgs./Cum. Using approved raw material
conforming to manufactured by BASF. ICI, BYER the international standard specification
over terrace including making groove 30mmx15mm in 3 m x 3m grids. (This work is to be
carried out through approved speciaslised sub-contractors experienced in polyurethane
insulation work with the approval of the consultant and shall be guaranteed fully effective
for a period of ten years. Nothwithstanding this, the responsibility of the effectiveness of the
treatment shall be fully, entirely and unqualifiedly be that of the main contractor for the
work.)
Sqm 1375
20 mm thick plaster (1:4) in 3 layers (details may be obtained from Consultant / Client on
chemical injection waterproofing). Sqm. 1302
Grouting with 25mm dia G.I. nozzles (Details may be obtained from Consultant / Client onchemical injection waterproofing). Sqm. 1412
On wall surfaces (actual treated area to be measured for payment in the following manner).
20mm thick cement mortar (1:4) with polymer based waterproofing compound plaster with
checken wire mesh (Details may be obtained from Consultant / Client on chemical injection
waterproofing).Sqm. 385
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
28/59
Sl. No. Description Unit Qty Rate Amount
Grouting with 25mm dia G.I. nozzles (Details may be obtained from Consultant / Client on
chemical injection waterproofing).Sqm.
16 Providing and laying waterproofing of basement with chemical injection method from
approved specialised firm all as per specifications carrying 10 years guarantee. (Tenderer
should submit the name of the specialist).
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Basement floor (Actual treated area to be measured for payment in the following manner):
20 mm thick plaster (1:4) in 2 layers (details may be obtained from Consultant / Client on
chemical injection waterproofing). Sqm. 580
Grouting with 25mm G.P. Nozzles detailed may be obtained from consultant / client on
chemical injection water proofing. Sqm. 440
On wall surfaces (actual treated area to be measured for payment in the following manner).
20mm thick cement mortar (1:4) with polymer based waterproofing compound plaster with
checken wire mesh (Details may be obtained from Consultant / Client on chemical injection
waterproofing). Sqm. 630
Grouting with 25mm dia G.I. nozzles (Details may be obtained from Consultant / Client on
chemical injection waterproofing). Sqm. 630
17 Providing and fixing G.I. Vent Pipe as per approved design or as directed by Engineer-in-
100 mm dia Meter 865 mm dia Meter 8
0
18 Providing, installation 6mm thick M.S. Puddle flange including welding with M.S. Pipe as
150 mm dia Each 4
100 mm dia Each 4
80 mm dia Each 8
65 mm dia Each 8
50 mm dia Each 12
40 mm dia Each 4
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
29/59
Sl. No. Description Unit Qty Rate Amount
32 mm dia Each 4
25 mm dia Each 8
19 Providing and fixing 560 mmdia C.I. Manhole cover with frame (heavyduty) total weight of
cover and frame hot less than 208 Kgs (Weight of cover 108 Kgs and weight of frame 100
Kgs.) Each 10
20 Providing and laying waterproofing treatment for Car park, Podium and gardens over
basement roof slab, all as per following specification carrying 10 years; guarantee; (Tenderer
should submit the name of specialist)
Note:- Used PPC Cement to be used conforming to IS: 1489 (Part-I)
Polymer modified cementeclous slurry coating of DICHTAMENT D5 + NAFUFILL BB1.
21 Polymer modified concrete screed 25mm thick using 8mm down aggregates (1:1:3) 1
cement : 1 aggregate : 3 coarse sand admixed with special dischatament DM .0.5% by
weight of cement Nafufill SBR 5% by weight of cement manufactured by MC Bauchemie (I)Pvt. Ltd.
22 All upstand masonary work with 20mm thick waterproof plaster (CM) 1 : 4 (1 cement : 4
coarse sand) admixed with DOCHTAMENT DM @ 200ml. Per bag of cement)
All corner junctions with EMCERCITE mortar (30x30)
23 Water proof screed or coba in proper slope using admixed with DICHTAMENT Dm 100
thick (Av.)
Final coating of DICHTAMENT DA + NBB2Sqm. 480
Note:- The treatment is to be carried out by a specialised agency with the approval of the
Engineer-In-Charge. The specialised agency should furnish the guarantee in the named
owner for a period of 10 years. Not with standing this, the responsebility of the effectiveness
of the treatment shall be entirely and unqualified be that of the main contractor for the work.
The tenderer to state the name of specialised firm.
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
30/59
Sl. No. Description Unit Qty Rate Amount
SUB-HEAD : XII : PILING WORK
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
31/59
Sl. Description Unit Qty Rate AmountSUB HEAD : 1 WATER SUPPLY
1 Providing and fixing G.I. Pipes complete with G.I. Fitting, Clamps,
including cutting, making the good wall. (Exposed on walls shafts and
terrace)
15 mm dia nominal bore Meter 58.00
20 mm dia nominal bore Meter 96.00
25 mm dia nominal bore Meter 134.00
32 mm dia nominal bore Meter 61.00
40 mm dia nominal bore Meter 79.0050 mm dia nominal bore Meter 27.00
2 Concealed pipe including painting with anti corrosive bitumastic paint,
cutting chases and making good the wall.
15 mm dia nominal bore Meter 206.00
20 mm dia nominal bore Meter 247.00
25 mm dia nominal bore Meter 181.00
32 mm dia nominal bore Meter 0.00
3 Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc. (external work)
25 mm dia nominal bore Meter 91.00
32 mm dia nominal bore Meter 42.00
Engineering Projects (I) limited
BPA Site,Rajgir
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Plumbing 1A
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
32/59
4 Making connection of G.I. distribution branch with G.I. main of
following sizes by providing and fixing tee, including cutting and
threading the pipe etc. Complete.
25 to 40 mm nominal bore nnection 14.00
5 Providing and fixing C.P.brass bib cock of approved quality confirming
to IS : 8931.
15 mm dia nominal bore Each 63.00
6 Providing and fixing C.P.brass stop cock (concealed) of standard design
and of approve dmake conforming to IS: 8931.
15 mm dia nominal bore Each 82.00
7 Providing and fixing gate valve with C.I. wheel of approved quality
(screwed end).
32 mm dia nominal bore Each 11.00
40 mm dia nominal bore Each 8.00
8 Providing and fixing brass ferrule with C.I. mouth cover including
boring and tapping the main.
25 mm dia nominal bore Each 11.00
9 Providing and fixing PVC connection pipe with brass unions.
45 cm length
15 mm dia nominal bore Each 57.00
10 Providing and fixing C.P. brass shower rose 15 or 20 mm inlet.
100 mm diameter Each 11.00
11 Painting G.I. pipes and fittings with two coats of anticorrosive
bitumastic paint of approved quality.
15 mm diameter pipe Each 47.00
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
33/59
20 mm diameter pipe Each 57.00
25 mm diameter pipe Each 107.00
32 mm diameter pipe Each 36.00
40 mm diameter pipe Each 76.00
50 mm diameter pipe Each 5.00
12 Providing and filling sand of grading zone V or coarser grade alround
the G.I. pipes in external work.
25 mm dia pipe Each 74.00
13 Providing and placing on terrace (at all floor levels) polyethylene water
storage tank of approved brand and manufacture with cover and suitable
locking arrangement and making necessary holes for inlet, outlet and
overflow pipes but without fittings and the base support for tank. Per Litre 50700.00
14 Providing and fixing C.P. brass long body, bib cock of approved qualityconforming to IS standards.
a) 15 mm nominal bore Each 22.00
15 Providing and fixing C.P. brass angle valve for basin mixer and gyser
points of approved quality conforming to IS: 8931
a) 15 mm nominal bore Each 197.00
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
34/59
Providing orange colour safety foot rest of minimum 6 mm thick plastic
encapsulated as per IS :10910 on 12 mm dia steel bar conforming to IS
:1786 having minimum cross section as 23 mm x25mm and over all
minimum length 263 mm and width as 165 mm with minimum 112 mm
space beween protruded legs having 2 mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard drawing and
suitable to with stand the bends test and chemical resistance test as per specifications and having manufacture's permanent identification mark
to be visible even after fixing , including fixing in manholes with
30x20x15 cm cement concrete block 1:3:6(1 cement :3 coarse sand: 6
graded stone aggregate 20 mm nominal size)complete as per standardEach 150.00
SUB HEAD :2 SANITARY INSTALLATION
16 Providing and fixing white vitreous china pedistal type water closet
(European type W.C. Pan) with seat and lid C.P. brass hinges and rubber
buffers, 10 litre low level P.V.C. flushing cistern with fittings. C.I. /
M.S. brackets 40mm diameter flush bend with fittings and clamps,
overflow arrangement with specials and mosquito proof coupling of
approved municipal design complete including painting of fittings and
brackets, cutting and making good the walls and floors wherever
W.C. pan with white solid plastic seat and lid. Each 54.00
17 Providing and fixing white vitreous china water closet squatting pan
(Indian type W.C. Pan) with 100 mm sand cast iron P or S trap.10 Litre
low level P.V.C. flushing cistern (of approved make) with fittings. C.I.
M.S. brackets, 32 mm diameter flush pipe with fittings and clamps,
overflow arrangement with specials and mosquito proof coupling of
approved municipal design including painting of fittings and brackets,
cutting and making good the walls and floors wherever required.
Long pan pattern W.C. pan of size 580 mm with flush pipe & overflow
arrangement.Each 14.00
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
35/59
18 Providing and fixing white vitreous china flat back or wall corner
typelipped urinal basin of 430x260x350 mm sizes respectively with
automatic flushing cistern with C.I./M.S. brackets standard size of G.I.
flush pipe and C.P. brass spreaders with brass unions and G.I. clamps
complete, including painting of fittings and brackets, cutting and making
good the walls and floors wherever required.
One urinal basin with 5 litre P.V.C. automatic flushing cistern. Each 12.00
19 Providing and fixing C.P. brass waste for sink or wash basin. 0.00
32 mm dia Each 90.00
40 mm dia Each 16.00
20 Providing and fixing PVC waste pipe for sink or wash basin including
PVC waste fittings complete.
Flexible Pipe
32 mm dia Each 74.0040 mm dia Each 9.00
21 Providing and fixing 100 mm sand cast Iron grating for gully, floor or
nahani trap. Each 106.00
23 Providing and fixing stainless steel jali (grating) with or without hole for
waste pipe for floor / nahani trap.
75 mm dia weight not less than 70 gms Each 42.00
24 Providing and fixing 600x450 mm bevelled shape edge or supertor ( or
approved quality) complete with 6 mm thick miror hard board ground
fixed to wooden cleats with C.P. brass screws and washers complete.
Each 74.00
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
36/59
25 Providing and fixing toilet paper holder
C.P. brass Each 63.00
26 Providing and fixing soil, waste and vent pipes
100 mm dia Sand cast iron S & S Pipe Meter 426.00
75 mm dia Sand cast iron S & S Pipe Meter 138.00
27 Providing and fixing M.S. holder-bat clamps of approved design to Sand
Cast iron / Cast iron (spun) pipe embedded in and including cementconcrete blocks 10 x 10 x 10cm of 1:2:4 mix ( 1 cement : 2 coarsesand
: 4 graded stone aggregate 20 mm nominal size) including cost of cutting
holes and making good the walls etc.
For 100 mm dia pipe Each 95.00
For 75 mm dia pipe Each 57.00
28 Providing and fixing bend of required degree with access door, insertion
rubber washer 3 mm thick bolts and nutts complete.
100 mm
Sand cast iron S&S Each 89.00
75 mm dia
Sand cast iron S&S Each 30.00
29 Providing and fixing double equal junction of required degree with
access door, insertion rubber washer 3mm thick, bolts & nuts complete.
100 x 100 x 100 x 100 mm
Sand cast iron S&S Each 12.00
75 x 75 x 75 x 75 mm
Sand cast iron S&S Each 1.00
30 Providing and fixing double equal plain junction of required degree.
100 x 100 x 100 x 100 mm
Sand cast iron S&S Each 12.00
75 x 75 x 75 x 75 mm
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
37/59
Sand cast iron S&S Each 1.00
31 Providing and fixing single equal plain junction of required degree with
access door, insertion rubber washer 3 mm thick bolts and nuts
100 x 100 x 100 mm
Sand cast iron S&S Each 12.00
75 x 75 x 75 mm
Sand cast iron S&S Each 1.00
32 Providing and fixing double unequal junction of required degree with
access door, insertion rubber washer 3 mm thick bolts complete.
100 x 100 x 75 x 75 mm
Sand cast iron S&S Each 9.00
33 Providing lead caulked joints to sand cast iron/ centrifugally cast (spun)
iron pipes and fittings of diameter.100 mm Each 156.00
75 mm Each 61.00
34 Providing and fixing M.S stays and clamps for sand cast iron /
centrifugally cast (spun) iron pipes of diameter.
100 mm Each 96.00
75 mm Each 58.00
35 Providing and fixing sand cast iron trap of self cleaning design with sand
cast iron screwed down or hinged grating with or without vent armcomplete, including cost of cutting and making good the walls and
floors.100 mm inlet and 100 mm outlet Each 38.00
100 mm inlet and 75 mm outlet Each 46.00
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
38/59
36 Cutting chases in brick masonry walls for following diameter sand cast
iron / centrifugally cast (spun) iron pipes and making good the same
with cement concrete 1:3:6 (1 cement : 3 coarse sand and 6 graded stone
aggregate 12.5mm nominal size) including necessary plaster in cement
mortar 1:4 (1 cement : 4 coarse sand)
100 mm Meter 30.00
75 mm Meter 13.00
37 Providing and fixing on wall face uplastidsed-PVC (working pressure 4
kg per sqcm) rain water pipes conforming to IS : 4985 including jointing
with seaf ring conforming to IS : 5382 leaving 10 mm gap for thermal
expansion.
75 mm diameter Meter 40.00
110 mm diameter Meter 230.00
38 Providing and fixing on wall face unplasticised PVC moulded
fittings/accessories for unplasticised-PVC rain water pipes conformingto (S:4985 including jointing with seal ring conforming to IS: 5382
leaving 10 mm gap for thermal expansion.
Single tee without door
110x110x110mm Each 29.00
Bend
75 mm bend Each 17.00
110 mm bend Each 19.00
TOTAL
Engineering Projects (I) limitedBPA Site,Rajgir
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
39/59
Sl.
No.
Description Unit Qty Rate Amount
SUB HEAD : 1 WATER SUPPLY
1 Providing and fixing ball valve (brass) of approved quality complete.
High or low-pressure with plastic floats
20 mm dia nominal bore Each 19
25 mm dia nominal bore Each 19
2 Construction masonry chamber 30 x 30 x 50 cm inside with 75 class designation brick
work in cementmortar 1:5 (1 cement : 5 fine sand) for stop cock, with C.I. surface box
100 x 100 x 75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary
excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone
aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement :
3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per
standard design.
With F.P.S bricks Each 20
3 Providing and fixing 600 x 120 x 5 mm glass shelf with edges rounded off supported on
anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixedwith 40 mm long screws, rawl plugs etc. complete.Each 69
4 Providing and fixing towel rail complete with brackets fixed to wooden cleats with C.P.
brass screws. Each 68
TOTAL
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Plumbing 1B
Engineering Projects (I) limitedBPA Site,Rajgir
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
40/59
Sl.
No.
Description Unit Qty Rate Amount
SUB HEAD : 1 WATER SUPPLY
1 Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall.
25 mm dia nominal bore Metre 34.00
SUB HEAD :2 SANITARY INSTALLATION
2 Providing and fixing inlets fi tting with max. 3 inlets 32, 40 or 50mm size
fabricated from 100mm dia pipes and fixed to CI trap and set in 1:2:4 cement
concrete as per standard drawing complete. Each 78.00
3 Providing and fixing white vitreous china flat back half stall urinal of
580x380x350mm with fully automatic battery operated, photo electric cell type
flushing system comprising of solenoid valve, concealed copper piping, wiring
& sensor complete in fully operating condition including standard size C.P.
brass flush pipe, spreader with union, CP clamps and screws, CP flanges, waste
fitting as per IS : 2556 and CP bottle trap, complete including cutting &
making good the walls and floor wherever requiredEach 73.00
4 Providig and Fixing white vitreous china oval wash basin of 560mm x 410mm
size with specially fabricated M.S. or CI brackets, 32mm CP brass waste of standard pattern, 32mm dia C.P. brass bottle trap Piller taps and making
connection to the waste pipe in wall with C.P wall flange and rubber adopter
complete with required accessories including painting of brackets and cutting
and making good the walls wherever required.Each 72.00
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Plumbing 1C
5 Providing and fixing white vitreous china Kitchen sink with C.I. brackets, C.P.
brass chain with rubber plug 40 mm C.P.brass waste and 40 mm C.P. brass trap
with necessary C.P. brass unions complete including painting brackets, fittings,
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
41/59
cutting and making goog the wall wherever required.
Kitchen sink with drain board.
Size 510 x 1040 bowl depth 178 mm Each 1.00
6 Providing and fixing rubber plug for sink or wash basin. Each 82.00
7 Providing and fixing G.I Class-B waste pipe.
32 mm Meter 60.00
50 mm Meter 56.00
8 Providing and fixing floor clean out plug / clean out plug for cast iron soil or
waste pipes comprising of C.I. Plug, nipple, bend including lead jointing etc.
complete.
For 100 mm dia pipe Each 35.00
TOTAL
Engineering Projects (I) limited
BPA Site,Rajgir
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
42/59
Sl. Description Unit Qty Rate Amount
Sub-head : I : Point Wiring
1 Wiring for Light point / Fan point / Exhaust Fan point / Call Bell / 6 Amp light
plug point with 1.5 sq.mm FR PVC insulated copper conductor single core cable
in surface / recessed PVC conduit, with modular switch, modular plate, suitable
size GI box and earthing the point with 1.5 sq.mm FR PVC insulated copper
conductor single core cable etc. as required.
a roup - o n roup - o nt
c) Group - C Point 489
2 Wiring for Light point / Fan point / Exhaust Fan point / Call Bell / 6 Amp light
plug point with 2x1.5 sq.mm PVC insulated stranded copper conductor cablealongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing
in surface/recessed PVC conduit as required. (Point shall be controlled / looped
from existing point).Point 525
3 Wiring for twin control Light point with 1.5 sq.mm FR PVC insulated copper
conductor single core cable in surface / recessed PVC conduit, 2 way modular
switch, modular plate, suitable size GI box and earthing the point with 1.5
sq.mm FR PVC insulated copper conductor single core cable etc. as required.Point 10
4 Wiring for light / power plug point with 2 x 4 sq.mm FR PVC insulated copper
conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 4
sq.mm FR PVC insulated copper conductor single core cable for loop earthing as
required. Metre 3171
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Electrical 1A
5 Wiring for light / power plug point with 4 x 4 sq.mm FR PVC insulated copper
conductor single core cable in surface / recessed PVC conduit alongwith 2 Nos.
4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
43/59
as required. Metre 1155
6 Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess, including providing and fixing 3 pin 5 / 6 amps modular
socket outlet and 5 / 6 amps modular switch, connection, painting etc.as
required. (For light plugs to be used in non residential buildings.)Each 144
7 Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess ,including providing and fixing 6 pin 20 / 16 amps
modular socket outlet and 15 / 16 amps modular switch, connection, painting
etc.as required. Each 69
8 Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess, including providing and fixing 3 nos 3 pin 5 / 6 amps
modular socket outlet and 1 no 15 / 16 amps modular switch,connection,
painting etc.as required. Each 40
9 Supplying and fixing 20 Amps, 240 Volts, SPN industerial type, Socket outlet,
with 2 pole and earth, metal enclosed plug top along with 20 amps, 2Pole,
RCCB in sheet steel enclosure, on surface or in recess with chained metalcover
for the socket out let and complete with connections, testing andcommissioning
etc. as required.
a) 20A, 3 pin socket outlet controlled by 20A 2P RCCB. Each 11
10 Supplying and fixing 20 Amps, 240 Volts, SPN industerial type, Socket outlet,
with 2 pole and earth, metal enclosed plug top along with 20 amps, C series,
MCB in sheet steel enclosure, on surface or in recess with chained metalcover
for the socket out let and complete with connections, testing andcommissioning
etc. as required. Each 10
11 Supplying and fixing of following sizes of PVC conduit alongwith the
accessories in surface / recess including painting in case of surface conduit or
cutting and making good the same in case of recessed conduit as required as per
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
44/59
a) 20mm dia 16 SWG PVC conduit. Metre 510
b) 25mm dia 16 SWG PVC conduit. Metre 5860
c) 32 mm dia 16 SWG PVC conduit Metre 1700
d) 38 mm dia 16 SWG PVC conduit Metre 400
e) 50 mm dia 16 SWG PVC conduit Metre 350
12 Supplying and drawing following sizes of FR PVC insulated copper conductor single core cable in the existing surface / recessed PVC conduit as required.
a) 2 x 6.0 sq.mm + 1 x 6.0 sq.mm Metre 965
b) 4 x 6.0 sq.mm + 1 x 6.0 sq.mm Metre 430
13 Wiring for group light point controlled from existing MCB in DB with 2x4
sq.mm PVC insulated stranded copper conductor single core cable in
surface/recessed PVC conduit alongwith 1 No. 4 sq.mm PVC copper conductor
cable for loop earthing as required (OUTDOOR RECESSED LIGHT). Metre 240
14 Wiring for circuit / submain wiring along with earth wire with the followingsizes of FR PVC insulated copper conductor, single core cable in surface /
recessed PVC conduit as required.
2 X 1.5 sq.mm +1 X 1.5 sq.mm Earth wire Metre 0
2 X 2.5 sq.mm +1 X 2.5 sq.mm Earth wire Metre 1795
2 x 10 sq.mm + 1 x 10 sq.mm earth wire Metre 640
4 x 10 sq.mm + 2 x 10 sq.mm earth wire Metre 550
4 x 16 sq.mm + 2 x 16 sq.mm earth wire Metre 715
4 x 25 sq.mm + 2 x 16 sq.mm earth wire Metre 400
15 Providing, fixing, connecting, testing and commisssioning of zinc passivated boxwith moulded plate in recess or on surface moulded type with following
including all necessary materials etc. as required.
a) 6/10 amp one way switch with 1 or 2 module plate. Each 18
16 Providing, fixing, connecting, testing and commisssioning of zinc passivated box
with moulded plate in recess or on surface moulded type with following
including all necessary materials etc. as required.
) 16/20 it h ith 1 2 d l l t E h 19
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
45/59
a) 16/20 amp one way switch with 1 or 2 module plate Each 19
Sub-head : II : Fans & Light Fixtures
Sub-Head : III - Distribution Boards
Sub-Head : IV - MV Panel Boards / Out-door Feeder Pillars
Sub-Head : V L.T. Cables and Cable Trays
1 Supplying, laying, testing & commissioning of following sizes, XLPE insulated,
armoured, alluminium cable 1100V grade on surface or existing cable tray and
to be fixed with M.S. clamps of suitable size as directed by the E/I complete in
all respects or with MS support including painting supply and providing cable
identification markers etc. The armouring of the cable shall be properly
connected with the earth conductor by clamps etc. complete as required.
a) 3.5 x 70 sq.mm Metre 45
b) 3.5 x 50sq.mm Metre 360
c) 3.5 x 35sq.mm Metre 0
d) 4 x 25sq.mm Metre 100
e) 3 x 25sq.mm Metre 0
f) 3 x 16sq.mm Metre 0
g) 3 x 10sq.mm Metre 0
h) 4 x 6 sq.mm Metre 0
i) 3 x 6sq.mm Metre 0
j) 3 x 4sq.mm Metre 200
k) 3 x 2.5sq.mm Metre 300
2 Supplying and making cable end termination complete with brass compression
gland, crimping thimbles and insulating and PVC sheathed aluminium conductor
cable of1.1 KV grade of the under noted sizes as required.
a) 3.5 x 70 sq.mm Set 4
b) 3.5 x 50sq.mm Set 6
c) 3.5 x 35sq.mm Set 0
d) 4 x 25sq.mm Set 8
e) 3 x 25sq.mm Set 4
f) 3 x 16sq.mm Set 4
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
46/59
g) 3 x 10sq.mm Set 4
h) 4 x 6 sq.mm Set 4
i) 3 x 6sq.mm Set 4
j) 3 x 4sq.mm Set 6
k) 3 x 2.5sq.mm Set 6
Sub-head : VI Earthing & Lightning Conductor System
1 Earthing with G.I. Earth plate 600 mm x 600 mm x 6 mm thick including
accessories and providing masonary enclosure with cover plate having locking
arrangement and watering pipe etc.(but without charcoal or coke and salt)
complete as required. Set 6
2 Earthing with copper Earth plate 600 mm x 600 mm x 3.15mm thick including
accessories and providing masonary enclosure with cover plate having locking
arrangement and watering pipe etc. (but without charcoal or coke and salt)
complete as required. Set 7
3 Extra for using salt and coke for G.I or copper plate earth electrode as required.
Set 9
4 Providing and fixing following G.I./Copper strip from earth electrode as
required.
a) 25x 5mm copper strip Metre 285
b) 25x6 mm GI strip Metre 220
c) 50x6 mm GI strip Metre 80
5 Providing and fixing of lightning conductor finiel, made of 25mm dia 300mm
long GI tube, having single prong at top with 85mm dia 6mm thick GI base plate
including holes etc. complete as required. Each 1
6 Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall
for lightning conductor as required. (for horizontal run). Metre 45
7 Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
47/59
7 Providing and fixing GI tape 20mm x 3mm thick on parapet or surface of wall
for lightning conductor as required (for vertical run). Metre 25
8 Providing and fixing testing joint, made of 20mm x 3mm thick GI strip, 125mm
long with 4 nos. of GI bolts, nuts check nuts and spring washers etc. complete as
required. Each 13
9 Providing and laying GI tape, 32mm x 6mm thick, on surface/recess for
connection complete as required. Metre 25
10 Earthing with GI earth pipe 4.5M long, 40mm dia including accessories, and
providing masonary enclosure with cover plate having locking arrangement etc.
(but without charcoal or coke and salt) complete as required. Set 5
11 Extra for using salt and charcoal for pipe earth electrode as required. Set 6
Sub-head : XII - Fire Alarm & Public Address System
Sub-head : XV - Lifts
Total (in Rs).
Sub Head - IX : MATV System
Sub Head - VIII : Telephone System
Engineering Projects (I) limited
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
48/59
Sl.No.
Description Unit Qty Rate Amount
Sub-head : I : Point Wiring
Sub-head : II : Fans & Light Fixtures
Sub-Head : III - Distribution Boards
Sub-Head : V L.T. Cables and Cable Trays
1 Supplying, laying, testing & commissioning of fo llowing sizes of XLPE insulated
armoured copper control cable of 1100 V grade on existing cable trench, surface of wall
with M.S. clamps / cable tray complete as required.
a) 4 x 16 sq.mm Meter 110
b) 4 x 10 sq.mm Meter 0
c) 4 x 6 sq.mm Meter 0
d) 3 x 6 sq.mm Meter 0
e) 3 x 10 sq.mm Meter 0
f) 3C x 1.5 sq.mm Meter 100
g) 5C x 1.5 sq.mm Meter 50
2 Supplying and fixing of CRCA sheet steel, perforated cable tray duly stove enamel painted of approved shade in position including fixing in trench/along wall or ceiling
complete with M.S. rod/flat hangers directly grouted in walls/ceiling or welded with
steel structure etc. with necessary materials etc. as required.
BPA Site,Rajgir
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Electrical 1B
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
49/59
100 mm wide x 50mm x 1.6mm thick R.M. 70
150 mm wide x 50mm x 1.6mm thick R.M. 200
300 mm wide x 50mm x 1.6mm thick R.M. 0
Sub-head : VI Earthing & Lightning Conductor System
3 Providing and fixing following 'B' Class G.I. Pipe from earth electrode as required.
a) 40mm dia. Metre 72
4 Providing and fixing 8 SWG G.I. wire on surface or in recess for loop earthing
alongwith the existing surface /recessed conduit/submain wiring/cable as requiredMetre 5
Sub-head : XII - Fire Alarm & Public Address System
Sub-head : XV - Lifts
Total (in Rs).
Sub Head - IX : MATV System
Sub Head - VIII : Telephone System
Engineering Projects (I) limitedBPA Site,Rajgir
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
50/59
Sl.
No.
Description Unit Qty Rate Amount
Sub-head : I : Point Wiring
1 Supplying and fixing suitable size GI box with modular plate and cover in
front on surface or in recess including providing & fixing of moulded plate
type 6 pin 25 Amps socket with plug top and single phase motor starters of
the minimum features of current setting over load protection etc as
required. (For A.C points ).Each 22
2 Supplying and fixing 32 Amps, 415Volts, TPN industerial type, Socket
outlet with 4 pole and earth, metal enclosed plug top along with 30 Amps
'C' Series, TP MCB in sheet steel enclosure, on surface or in recess with
chained metalcover for the socket out let and complete with connections,
testing and commissioning etc. as required.
Each 6
3 Providing, fixing, connecting, testing and commisssioning of Aviation
Light including drawing of control cable complete as required. Each 1
Sub-head : II : Fans & Light Fixtures
1 Supply, Installation, testing & commissioning of box type, fluorescent
luminaire, powder coated complete with Electronics ballast, lockable
holders and lamp etc. complete as required. Similar to Philips Cat. No.
TMS 122 / 128 HF Each 66
2 Supply, Installation, testing & commissioning of box type, fluorescent
luminaire, powder coated, complete with Electronics ballast, lockable
holders and lamp etc. complete as required.Similar to Philips Cat. No.
TMS 122 / 228 HFEach 26
BILL OF QUANTITY FOR PACKAGE B
(Package B-CCWC , MTS,CS,ES,ESS,UGT,WT-6,GG,PG)
Electrical 1C
3 Supply, Installation, testing & commissioning of box type, fluorescent
luminaire, powder coated, complete with dimmable ballast, lockable
holders and lamp etc. complete as required.Similar to Philips Cat. No.
TMS 122 / 228 HFE h 10
-
8/17/2019 CIVIL WORKS BILL OF QUANTITY
51/59
Each 10
4 Supply, Instal