Application Note

Ericsson MD110 BC12 SP5 using E1 ISO-QSIG to Cisco Unified CallManager 5.0

Table Table of Contents Introduction .............................................................................................................................................................................................................. 1 Network Topology.................................................................................................................................................................................................... 2 Limitations................................................................................................................................................................................................................ 2 System Components ................................................................................................................................................................................................. 3 Hardware Requirements ...................................................................................................................................................................................... 3 Software Requirements........................................................................................................................................................................................ 3 Features .................................................................................................................................................................................................................... 3 Configuration............................................................................................................................................................................................................ 4 Configuring the Ericsson MD-110 PBX ............................................................................................................................................................. 4 Configuration Menus and Commands ................................................................................................................................................................. 4 Cisco CallManager Configuration..................................................................................................................................................................... 11 Acronyms................................................................................................................................................................................................................ 42

Introduction . This is an application note for connectivity of Ericsson MD-110 Release BC12 PBX with Cisco Unified CallManager Release 5.0 via Cisco 3845 w/ VWIC-2MFT-E1 as MGCP gateway using ISO QSIG protocol. The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability with the Cisco Unified CallManager connected to the PBX via Cisco3845 w/ VWIC-2MFT-E1 link as MGCP gateway. Connectivity is achieved by using the PRI QSIG E1 protocol type on the MGCP gateway with CallManager Service parameter QSIG variant of ISO and ISO switch type on the Ericsson MD-110 PBX.

This Application Note uses the Cisco3845 w/ VWIC-2MFT-E1 voice gateway, however other Cisco voice gateways are also an option to use since CallManager QSIG implementation does not depend on the physical interface.

2006 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 1 of 44 EDCS#519719 Rev # 1

Network Topology

Basic Call Setup End-to-End Configuration

Figure 1.Limitations

Network Topology or Test Setup

Calling/Connected Name Restrictions Ericsson phone displayed Calling/Connected Name when Cisco CallManager sends it as restricted. ANF-PR-Additional Network Feature Path Replacement for Call Diversion by join The Ericsson MD-110 PBX did not initiate Path Replacement proposal for a call that originated from the Ericsson PBX and was diverted from CallManager to another Ericsson MD-110 PBX node. SS-MWI MWI LEDs are not activated/deactivated when a message is left for a station not residing on the Message Centre PINX. The Ericsson MD-110 PBX did not utilize the standard QSIG-MWI code to activate/deactivate MWI LEDs at the far-end PINX stations. The Ericsson MD110 utilized a Manufacturer Specific code across the QSIG connection to support this feature.

2006 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 2 of 44

System Components Hardware Requirements Cisco Hardware Cisco 3845 w/ VWIC-2MFT-E1 Cisco Unified CallManager Server

Ericsson MD110 PBX Hardware Circuit card TL76/1, PRI-E1 Special cards, blades, or cables required

Software Requirements Cisco Unified CallManager version: 5.0 Ericsson MD110 software release: BC12 SP5 Cisco 3845 IOS release: 12.4

Features Features Supported CLIP-Calling Line (Number) Identification Presentation CLIR-Calling Line (Number) Identification Restriction CNIP-Calling Name Identification Presentation COLP-Connected Line (Number) Identification Presentation COLR- Connected Line (Number) Identification Restriction CONP-Connected Name Identification Presentation Sending Alerting Name Call Back/Call Completion CT-Call Transfer (by join) CFU-Call Forwarding Unconditional CFB-Call Forwarding Busy CFNR-Call Forwarding No Reply ANF-PR-Additional Network Feature Path Replacement (for Call Transfer by join) ANF-PR-Additional Network Feature Path Replacement (for Trombone connection) Features Not Supported Ericsson PBX did not honor CNIR-Calling Name Identification Restriction Ericsson PBX did not honor CONR- Connected Name Identification Restriction Ericsson PBX did not support Network Call Forwarding (CFU, CFB, CFNR) by join. It always invoked Reroute on every external CF. Ericsson PBX did not support Q.SIG MWI- Message Waiting Indication (lamp ON, lamp OFF)

2006 Cisco Systems, Inc. All right reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com Page 3 of 44

Configuration Configuring the Ericsson MD-110 PBX Warning: The Ericsson MD-110 PBX user interface is very precise. All parameters and options are mapped to position-dependent numeric fields within the various commands listed below. The user must have the correct revision of the Ericsson MD-110 PBX administration manual to be able to decipher each field position and determine its meaning. It is therefore not advisable to make changes to an MD-110 PBX unless you know exactly what you are doing. A single number out of place in a command string can cause unusual behavior on the PBX. Configure the Ericsson MD-110 PBX in the following sequence: 1. ROCAI Route Category Initiate 2. RODAI Route Data Initiate 3. ROEQI Route Equipment Initiate 4. RODDI Route External Destination

Configuration Menus and CommandsEricson MD110 Configuration

Route Category Initiate

Setup internal characteristics for the route. Ex. Traffic direction, services, Bearer capabilities.For Ericsson1 node< ROCAP:ROU=100; ROUTE CATEGORY DATA ROU SEL TRM SERV 2110030000 NODG DIST DISL TRAF 0 30 128 SIG BCAP

100 711000000000001 5 END