Circuits IIEE221

Unit 4Instructor: Kevin D. Donohue

Complex Power, Power Conservation, Power Factor Correction, and Applications

Complex Power

Complex power represents its real and reactive components.

Let the sinusoidal voltage and current in a load be denoted by:

Then the complex power is expressed as:

imvm IIVV ˆ ˆ

ivrmsrmsirmsvrmsim

vm IVIV

IVIVS

222

ˆˆˆ

*

Complex Power The real and imaginary terms of complex power

represent the real (P) and reactive (Q) components of the power:

Note that many previously described power quantities can be obtained from complex power

jQPS

IVjIVIVS ivrmsrmsivrmsrmsivrmsrms

ˆ

sincosˆ

iv

ivrmsrms

ivrmsrms

rmsrms

S

P

IVQS

IVPS

IVSS

cosFactorPower

VARs units sinˆImPower Reactive

Watts units cosˆRePower (Average) Real

VAs units ˆPowerApparent

Complex Power with Impedance

Load impedance can be expressed as:

The above relationship can be used to express power in terms of the impedance and either current or voltage magnitudes.

jXRI

V

I

VZ iv

rms

rms

rms

rms

ˆ

ˆˆ

*

2*

*

2**

ˆ

ˆ

ˆˆˆˆˆ

ˆˆˆˆˆˆˆ

Z

V

Z

VVIVS

IZIIZIVS

rmsrmsrmsrmsrms

rmsrmsrmsrmsrms

Power Triangle

The real and reactive terms of a load (R, X) can be represented by a triangle from the vector addition. This triangle will be similar to the triangle formed by the real (P) and reactive (Q) components and complex power:

Power Triangle

The power triangle provides a graphic representation of leading and lagging properties of the load:

(lagging) Load Inductive0Q

(leading) Load Capacitive0Q

Load Resistive0

Q

Conservation of Power

In a given circuit the complex power absorb (denoted by positive values) equals the complex power delivered (denoted by negative values).

For a circuit with N elements the sum of all power is zero:

Note that the above is only true for the real and reactive components. This is not true for apparent power.

N

iiS

1

ˆ0

Power Factor Correction

For a fixed generator voltage and average power in a load, the output current should be minimized to limit losses over the power line. This is done by adding reactive components to the power systems to bring the PF to 1 (or close to it).

SV

SILineZ

LoadZ CZ

Power Factor Correction

For an inductive load (PF lagging) a purely capacitive load can be added to the line to bring the power factor closer to 1. Show that for a load with PF = x1 lagging and apparent power S1 = Irms Vrms that a new power factor of PF = x2 is achieved by placing a capacitor in parallel with the load (shunt) such that:

leadingfor )(cos

laggingfor )(cos and )(cos where

))tan())(tan(cos(

21

21

211

1

22111

x

xx

V

SC

rms

Power Factor Correction

For a capacitive load (PF leading) a purely inductive load can be added to the line to bring the power factor closer to 1. Show that for a leading load with PF = x1 leading and apparent power S1 = Irms Vrms that a new power factor of PF = x2 is achieved by placing a shunt inductor across the load such that:

leadingfor )(cos

laggingfor )(cos and )(cos where

))tan())(tan(cos(

21

21

211

1

1211

2

x

xx

S

VL rms

Power Meters

Power meters must simultaneously measure the voltage (in parallel) and the current (in series) associated with load ofinterest.

The meter deflection is proportional the average power.

Electricity Consumption Cost

The kilowatt-hours (kWh) to a customer is measured with a kWh meter corresponding to the average power consumed over a period of time.

The cost/rate of the kWh may very depending on when the power is used (high vs. low demand) and how much total power has been consumed (cost may go down after so many kWh used).

A penalty may also be imposed for having a pf below a set figure (i.e. 0.9) since it requires larger currents and the unmetered losses in the line to the customer may consume excessive power.

A fixed overhead amount is charged simply to maintain the power delivery system, even if you use no power.