Chicken Coop Pet Cottage Assembly Instruction - Costco · East Bethel, MN USA 763-753-7374 Parts...

East Bethel, MN USA 763-753-7374

Continued

1 Parts Identifi cation Box 1

Remove contents from Box 1 of 2.Stack matching pieces in piles. Using the parts list, locate and count the individual pieces and verify that you have received the correct number of pieces.

If any pieces are missing or replacement parts are required, contact Gronomics at 1-855-299-6727.

NOTE: Ground preparation is optional, however we recommend leveling area under frame of product, or place product directly on a flat level surface. 2

13131414

1515 1818 1919

3

74

5

6

Box 1 of 2ITEM QTY. PART # DESCRIPTION

1 2 NASR11 Nesting Angle Side Rail, 11-1/2” x 4-1/2”2 4 NSR11.5 Nesting Side Rail, 11-1/2” x 5-1/2”3 4 NSR12 Nest Side Rail, 11-5/8” x 4”4 45 4

N/A Screw, #8 x 3/4”RSS10-2ZY Screw, GRK #10 x 2”

6 1 N/A Ramp Hook7 2 NP12 Nesting Post, 12-3/8” x 1-7/8”8 4 NP15 Nesting Post, 15-1/4” x 1-7/8”9 2 CBP37 Rear Post, 36-3/4” x 3-1/4”10 2 CBNB41 Bottom Notched Board, 40-7/8” x 5-1/4”11 2 CBB41 Bottom Board, 40-7/8” x 5-1/4”12 2 CBRB41 Bottom Ripped Board, 40-7/8” x 3-5/8”13 6 CS40 Coop Side Board, 40” x 5-3/8”14 1 CFRONT40 Front Cleat Side Rail, (w/Logo), 40” x 4”15 1 CBACK40 Back Cleat Side Rail, 40” x 4”16 1 ACS12 Angled Coop Side RH, 12-1/2 ” x 14-5/8”17 1 ACS12 Angled Coop Side LH, 12-12” x 14-5/8”18 1 RAMP Ramp, 39-3/4” x 11”19 1 RR41 Roost Rod, 40-3/4” x 1-1/4”20 2 RRH2 Roost Rod Holder

Chicken Coop Pet Cottage 45"L x 45"Wx 48"H Assembly Instruction

Item #: CCPC 45-45

12121010 111198

Packaged & Inspected by: Date:

1

1616 1717

2020

Torx® T25

Phillips


Parts Identifi cation Box 2

Chicken Coop Pet Cottage 45"Lx 45"Wx 48"H Assembly Instruction

Item #: CCPC 45-45




NOTE: Ground preparation is optional, however we recommend leveling area under frame of product, orplace product directly on a flat level surface.

21212222 2323 2424


CCFoldLid Folding LidSD4021 Screen Panel, W/Door 40” x 21-1/2”SS4021 Screen Panel, 40” x 21-1/2”CFP48 Front Post, 47-3/4” x 3-1/4”

SW4021 Screen Panel, 40” x 21-1/2” w/Winterized Window Cover (Not Shown)

2122232425

11321

Product Care & Maintenance Western Red Cedar will turn a weathered grey if left unfinished. Although no finish is required for cedar products when used outdoors, a natural oil finish applied regularly will help maintain the beauty and minimize cracking and drying. It is recommended to use Gronomics Garden Bed Oil (Item # GBO-1Q), a non-toxic, food safe finish that is very easy to apply.


Continued

2 Parts Identifi cation Box 2



NOTE: It is recommended to place a protective layer between the ground and the pieces during assembly. This will help prevent damage to the pieces.


21 1 CCFoldLid Folding Lid22 1 SD4021 Screen Panel, W/Door 40” x 21-1/2”23 3 SS4021 Screen Panel, 40” x 21-1/2”24 2 CFP48 Front Post, 47-3/4” x 3-1/4”25 1 SW4021 Screen Panel, 40” x 21-1/2” w/Winterized Window Cover (Not Shown)

21212222 2323 2424

3 Screen Panel Assembly

NOTE: Always assemble the chicken coop on a level surface and keep posts and parts square when assembling.

NOTE: The chicken coop pet cottage contains one screen panel w/door (Item 22). The screen panel w/door can be located on any side desired of the chicken coop pet cottage, choose which side to locate the screen panel w/door when performing steps 3 thru 5.

Position a screen panel (Item 22 or Item 23) with the screw heads facing you.

Position the 47-3/4” posts (Item 24) with the fl at end (straight cut) towards the ground and with a slot facing you and a slot facing left and right.

Align the screen panel tabs with the post slots and slide a post down onto the screen panel on each end.

NOTE: Make sure the screen panel tabs are fully inserted into the post slots.

2323

2424 2424

2222

Locate the screen panel w/door (Item 22) on any side of the chicken coop pet cottage when performing steps 3 - 5.

Install the screen panel w/door with the door latch located upward.

Door Latch


Continued

2323

4 Screen Panel Assembly Continued

Align a screen panel (Item 22 or Item 23) with the screw heads facing in. Align the screen panel tabs with the post slots and slide the screen panel down on both posts.

2323

5 Screen Panel Assembly Continued

Position a screen panel (Item 22 or 23) (screw heads facing away from you) between the two previously installed screen panels.

Position the 36-3/4” posts (Item 9) with the fl at end (straight cut) towards the ground, make sure the top of the post tapered cut is slopped towards you.

Align the screen panel tabs with the post slots and slide the posts down.

2323

6 Side Rail And Coop Side Board Assembly

Install the front cleat side rail (w/Logo) (Item 14) (with the cleat located at the bottom and facing in) between the two 47-3/4” posts and slide down.

Install the back cleat side rail (Item 15) (with the cleat located at the bottom and facing in) between the two 36-3/4”posts and slide down.

Install four 40” x 5-3/8” coop side boards (Item 13) between the posts and slide down.

1515

7 Roost Floor Assembly

Install the 40-7/8” x 5-1/4” bottom notched boards (Item 10), 40-7/8” x 3-5/8” bottom ripped boards (Item 12), and 40-7/8” x 5-1/4” bottom boards (Item 11) as shown on each side of the chicken coop.

1010 1010

1212 1212

1111 1111

1414

1313

1313

9

9


Continued

Place the ramp (Item 18) onto the front cleat side rail (w/ Logo) (Item 14) as shown. Lower the ramp end with the handle to the ground.

Measure 8” to 10” from the front cleat side rail (w/ Logo) (Item 14), then measure 6” up from the bottom notched board and place a mark. Center the roost rod holder on the mark and secure the roost rod holder (Item 19) with a screw (Item 4).

Repeat procedure on the opposite side and secure the roost rod holder (Item 20).

NOTE: When installing the roost rod holder with the open end, make sure the open end of the roost rod holder is located upward.

8 Ramp And Roost Rod Holder Assembly

1818 20201414

2020

8” to 10”6”

Roost Rod And Angled Coop Side Assembly

Place the roost rod (Item 19) into the roost rod holders.

Align the screen panel w/ winterized window cover (Item 25) tabs (screw heads facing in) with the post slots and slide the screen panel down.

NOTE: The winterized window cover can be installed or removed from the screen panel (Item 25) as desired.

Align the angled coop side RH (Item 16) & angled coop side LH (Item 17) between the posts and slide down.

2525

17171616

1919

9


Continued

Place the nesting boxes as shown and install four #10 x 2"screws (Item 5) from the outside of the coop into nesting boxes as shown.

Nesting Box Assembly

Assemble the nesting boxes as shown.

1212

Nesting Box Assembly Continued1313

11

2

8

88

83

3

3

3

55 5

Using the handle on the ramp (Item 18), raise the ramp up until the ramp is level with the fl oor. Place the ramp hook (Item 6) onto the ramp handle and secure the ramp hook to the coop side board with two #8 x 3/4” screws (Item 4).

NOTE The ramp can be positioned in the raised or lowered position as desired.

Coop Side Board Assembly

Install the two remaining 40’ x 5-3/8” coop side boards (Item 13) between the posts and slide down.

1010

1313

Ramp And Ramp Hook Assembly1111

18186

7 7

4


NOTE: Make sure the folding lid is positioned as shown (far right) before placing onto the chicken coop. The open end (no trim) of the folding lid located at the bottom, to allow water to run off.

Install the folding lid (Item 21) onto the chicken coop as shown. Make sure the folding lid notches are aligned and positioned onto the chicken coop screen panel and coop side board.

Close the folding lid.

NOTE: The winterized window cover is installed onto the upper screen panel to help protect pets from inclement weather, but can be removed in the summer.

Folding Lid Assembly

2121

2222

Lid Notches

1414

Folding Lid

If desired, install the winterized window cover onto the outside of the upper screen panel.

NOTE: Open or close the door as desired on the screen panel w/door (Item 22).

Product Care & MaintenanceWestern Red Cedar will turn a weathered grey if left unfinished. Although no finish is required for cedar products when used outdoors,a natural oil finish applied regularly will help maintain the beauty and minimize cracking and drying. It is recommended to use Gronomics Garden Bed Oil (Item # GBO-1Q), a non-toxic, food safe finish that is very easy to apply.


Continued

NOTE: The chicken coop run kit can be installed on the left, right or back side of the chicken coop or multiple run kits can be added to the chicken coop.

Remove the chicken coop folding lid.

NOTE: Remove the chicken nest from the side that the run kit is to be install. If installing multiple run kits or installing the run kit on the back side of the chicken coop remove both chicken nests.

Remove the two screws from the chicken nest posts.

Remove the chicken nest.

1 Parts Identifi cation

Remove contents from Box.Stack matching pieces in piles. Using the parts list, locate and count the individual pieces and verify that you have received the correct number of pieces.

NOTE: Ground preparation is optional, however we recommend leveling area under frame of product, or place product directly on a flat level surface.

3

4

Parts ListITEM QTY. PART # DESCRIPTION

1 2 SP4021 Screen Panel, 40” x 21-1/2”2 1 BP4021 Blank Panel Screenless (w/Cleat), 40” x 21-1/2”3 2 CEXTR45 Extension Roof, 45” x 21”4 2 CCP2175 Extension Post, 21-3/4 x 3-3/4”

Chicken Coop Run Kit 45"L x 45"W x 23”H Assembly Instruction

Item #: CCPCR 45-45


2 Chicken Coop Disassembly

1 2

Screw

Chicken Nest

Screw



3 Chicken Coop Disassembly Continued

Remove the roost rod.

Remove the angled coop side by sliding upward until both ends of the side panel assembly are removed from the posts.

Remove the two coop side boards by sliding upward until the side panel boards are removed from the posts.

Remove the screen panel by sliding upward until the screen panel is removed from the posts.

Coop Side Boards

Angled Coop Side

Screen Panel

4 Chicken Run Kit Assembly

Remove the notched bottom board.

Align and install the blank panel (Item 2) between the posts with the cleat located at the top and facing you. Slide the blank panel down to the ground.

Re-install the notched bottom board. Then re-install the coop side boards, angled coop side and chicken nest (see steps 3 & 2).

Notched Bottom Board

Blank Panel Cleat Located At Top

5 Chicken Run Kit Assembly Continued

Install the two screen panels (Item 1) (with screw heads facing in) into the slots on the chicken coop posts and slide down.

Place the screen side that was removed from the chicken coop in step 2 between the screen panels (Item 1) (with screw heads facing in).

Align the screen tabs with the slots on the 21-3/4” posts (Item 4) and slide the post down onto the screen panels.

Roost Rod

2

1

4

4

Screen Panel Removed From Chicken Coop

Install the two extension roof panels (Item 3) on top of the screen panels.

Re-install the chicken coop folding lid.

6 Chicken Run Kit Assembly Continued

Folding Lid

3

Chicken Coop Pet Cottage Assembly Instruction - Costco · East Bethel, MN USA 763-753-7374 Parts...

Documents

Transcript of Chicken Coop Pet Cottage Assembly Instruction - Costco · East Bethel, MN USA 763-753-7374 Parts...