CHEVROLET/GMC SILVERADO/SIERRA CREW … 2 SIDED.doc Rev: 0 CHEVROLET/GMC SILVERADO/SIERRA CREW CAB...

2
09001 2 SIDED.doc Rev: 0 CHEVROLET/GMC SILVERADO/SIERRA CREW CAB – PART NO. 09001 INSTALLATION INSTRUCTIONS Congratulations on your purchase of the Husky Gear Box. The Gear Box was designed to fit under the rear seat of your truck or SUV. The Gear Box gives you a place to store loose items and clutter and ultimately help keep your vehicle organized. It’s designed to fit your vehicle with or without your Husky Liners in place and only takes a few minutes to install. PACKAGE CONTENTS Gear Box – Part No: 09001 (1) Safety Straps with Strap Locks (2) Dividers (2) Installation Instructions (1) INSTRUCTIONS 1) Open and remove the Gear Box from the shipping box and protective plastic bag. 2) Install the safety straps into slots located on the back wall of the Gear Box (Figure 1 and 2). The strap locks should be upright with the hinge facing away from the Gear Box. Figure 1 Figure 2 3) Lift the rear seats into the upright position and install the Gear Box. The safety straps should be facing towards rear of your vehicle. 4) Install the passenger side strap through the hole in the passenger side metal seat bracket (Figure 3). Feed the strap through the strap lock and fasten. Pull on the strap to make sure the strap and the strap lock has been properly fastened. 5) Install the drivers side strap around the lower metal seat belt bracket (Figure 4). Make sure that the strap is around the metal and not just around the seat belt itself. Once again, feed strap through lock and fasten. Pull on the strap to make sure it is properly fastened.

Transcript of CHEVROLET/GMC SILVERADO/SIERRA CREW … 2 SIDED.doc Rev: 0 CHEVROLET/GMC SILVERADO/SIERRA CREW CAB...

09001 2 SIDED.doc

Rev: 0

CHEVROLET/GMC SILVERADO/SIERRA CREW CAB – PART NO. 09001

INSTALLATION INSTRUCTIONS Congratulations on your purchase of the Husky Gear Box. The Gear Box was designed to fit under the rear seat of your truck or SUV. The Gear Box gives you a place to store loose items and clutter and ultimately help keep your vehicle organized. It’s designed to fit your vehicle with or without your Husky Liners in place and only takes a few minutes to install. PACKAGE CONTENTS Gear Box – Part No: 09001 (1) Safety Straps with Strap Locks (2) Dividers (2) Installation Instructions (1) INSTRUCTIONS

1) Open and remove the Gear Box from the shipping box and protective plastic bag. 2) Install the safety straps into slots located on the back wall of the Gear Box (Figure 1 and 2). The strap locks should

be upright with the hinge facing away from the Gear Box.

Figure 1 Figure 2

3) Lift the rear seats into the upright position and install the Gear Box. The safety straps should be facing towards rear

of your vehicle. 4) Install the passenger side strap through the hole in the passenger side metal seat bracket (Figure 3). Feed the strap

through the strap lock and fasten. Pull on the strap to make sure the strap and the strap lock has been properly fastened.

5) Install the drivers side strap around the lower metal seat belt bracket (Figure 4). Make sure that the strap is around the metal and not just around the seat belt itself. Once again, feed strap through lock and fasten. Pull on the strap to make sure it is properly fastened.

09001 2 SIDED.doc

Rev: 0

Figure 3 Figure 4

6) Install the 2 dividers and you are ready to organize. If you are storing long items it may be necessary to remove the dividers. Also, small loose items can potentially roll around and become somewhat annoying. Simply place these items in a rag, towel, etc… roll them up and place in the Gear Box. If you have questions about your installation or any other Husky product, please call us at: 1-800-344-8759 M-F 8:00 am to 5:00 pm Central Time.