Chemical Process Piping Systems... Corrosion Resistant Fluid and Air Handling Systems. Chemical...
Transcript of Chemical Process Piping Systems... Corrosion Resistant Fluid and Air Handling Systems. Chemical...
www.SimtechUSA.com
Corrosion Resistant Fluid and Air Handling Systems.
Chemical ProcessPiping Systems
Polypropylene Butt Fusion Dimensional Data
�
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
TaBlE oF ConTEnTS
Pn10 / SDR 11
Pipe.............................................................................................................................................5
Butt Weld Fittings Adapters: Female ................................................................................................................. 27Adapters: Male ..................................................................................................................... 26Backing Rings ....................................................................................................................... 21Caps: Dome .......................................................................................................................... 23 Caps: Flat ............................................................................................................................. 22Elbows: 90° ............................................................................................................................ 6Elbow: 90° - Extended ........................................................................................................... 7Elbow: 45° - Extended ....... ................................................................................................... 8Lateral: 45° ........................................................................................................................... 24Lateral: 60° ........................................................................................................................... 25Reducer: Concentric ........................................................................................................13-15Reducer: Concentric - Extended ......................................................................................16-17Reducer: Eccentric - Extended ............................................................................................. 18Stub Ends ............................................................................................................................. 19Stub Ends - Extended ........................................................................................................... 20Tee ......................................................................................................................................... 9Tee: Reduced ........................................................................................................................ 10Tee - Extended .................................................................................................................... 11Tee: Reduced - Extended ...................................................................................................... 12Union: EPDM ...................................................................................................................... 28Union: VITON ..................................................................................................................... 29
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�1.05�609
ChemicalProcess Piping Systems - Dimensional Data
Pn6 / SDR 17.6
Pipe.............................................................................................................................................31
Butt Weld Fittings Backing Rings ....................................................................................................................... 41Caps: Dome .......................................................................................................................... 42Caps: Flat ............................................................................................................................. 43Elbows: 90° .......................................................................................................................... 32Elbow: 90° - Extended ......................................................................................................... 33Elbow: 45° - Extended ....... ................................................................................................. 34Lateral: 45° ........................................................................................................................... 44Lateral: 60° ........................................................................................................................... 45Reducer: Concentric ........................................................................................................37-39Stub Ends ............................................................................................................................. 40Tee ....................................................................................................................................... 35Tee: Reduced ........................................................................................................................ 36
Pn3.2 / SDR 33
Pipe.............................................................................................................................................47
Butt Weld Fittings Backing Rings ....................................................................................................................... 51Elbows: 90° .......................................................................................................................... 48Stub Ends ............................................................................................................................. 50Tee ....................................................................................................................................... 49
�
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
150psi Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
51.05�609
ChemicalProcess Piping Systems - Dimensional Data
PRESSURE PIPE
Description: Pressure Pipe PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Extruded, Stress Relieved
Connection: Butt Fusion
PN 10 / SDR 11
Nomnial Actual OD D S Weight Weight Part
Size Size in in (lbs./ m) Lbs. Foot Number
3/8" 0.6�0 (16mm) 0.6�0 0.071 0.�09 0.065 PP05000016
½" 0.787 (�0mm) 0.787 0.075 0.��5 0.07� PP050000�0
¾" 0.98� (�5mm) 0.98� 0.091 0.�61 0.11� PP050000�5
1" 1.�60 (��mm) 1.�60 0.11� 0.570 0.178 PP050000��
1¼" 1.575 (�0mm) 1.575 0.1�6 0.90� 0.�8� PP050000�0
1½" 1.969 (50mm) 1.969 0.181 1.�0� 0.��9 PP05000050
�" �.�80 (6�mm) �.�80 0.��8 �.��� 0.69� PP0500006�
�½" �.95� (75mm) �.95� 0.�68 �.080 0.96� PP05000075
�" �.5�� (90mm) �.5�� 0.��� �.�66 1.�96 PP05000090
�" �.��1 (110mm) �.��1 0.�9� 6.6�� �.069 PP05000110
�½" �.9�1 (1�5mm) �.9�1 0.��9 8.60� �.688 PP050001�5
5" 5.51� (1�0mm) 5.51� 0.500 10.71� �.��8 PP050001�0
6" 6.�99 (160mm) 6.�99 0.575 1�.058 �.�9� PP05000160
7" 7.087 (180mm) 7.087 0.6�6 17.75� 5.5�8 PP05000180
8" 7.87� (�00mm) 7.87� 0.717 �1.890 6.8�1 PP05000�00
9" 8.858 (��5mm) 8.858 0.807 �7.7�0 8.66� PP05000��5
10" 9.8�� (�50mm) 9.8�� 0.89� ��.100 10.656 PP05000�50
11" 11.0�� (�80mm) 11.0�� 1.000 ��.680 1�.��8 PP05000�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 5�.1�0 16.91� PP05000�15
1�" 1�.976 (�55mm) 1�.976 1.�68 68.6�0 �1.�50 PP05000�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 87.1�0 �7.��5 PP05000�00
18" 17.717 (�50mm) 17.717 1.610 110.��0 ��.��� PP05000�50
�0" 19.685 (500mm) 19.685 1.787 1�5.960 ��.�87 PP05000500
D
S
6
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Description: Elbow: 90° PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
Elbow: 90°
PN 10 / SDR 11
Nomnial Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 0.157 0.866 0.011 PP050100�0
¾" 0.98� (�5mm) 0.98� 0.091 0.197 1.06� 0.015 PP050100�5
1" 1.�60 (��mm) 1.�60 0.11� 0.197 1.�78 0.0�7 PP050100��
1¼" 1.575 (�0mm) 1.575 0.1�6 0.197 1.7�� 0.075 PP050100�0
1½" 1.969 (50mm) 1.969 0.181 0.�76 �.087 0.1�9 PP05010050
�" �.�80 (6�mm) �.�80 0.��8 0.�76 �.598 0.�68 PP0501006�
�½" �.95� (75mm) �.95� 0.�68 0.��� �.150 0.�51 PP05010075
�" �.5�� (90mm) �.5�� 0.��� 0.��6 �.661 0.7�6 PP05010090
�" �.��1 (110mm) �.��1 0.�9� 0.�7� �.5�8 1.�69 PP05010110
�½" �.9�1 (1�5mm) �.9�1 0.��9 0.669 5.118 1.8�7 PP050101�5
5" 5.51� (1�0mm) 5.51� 0.500 0.591 5.709 �.519 PP050101�0
6" 6.�99 (160mm) 6.�99 0.575 0.709 6.575 �.8�8 PP05010160
7" 7.087 (180mm) 7.087 0.6�6 0.591 7.��� 5.�90 PP05010180
8" 7.87� (�00mm) 7.87� 0.717 0.7�8 8.110 7.667 PP05010�00
9" 8.858 (��5mm) 8.858 0.807 0.8�7 9.�91 10.�18 PP05010��5
10" 9.8�� (�50mm) 9.8�� 0.89� 0.787 10.079 1�.8�8 PP05010�50
11" 11.0�� (�80mm) 11.0�� 1.000 0.9�5 11.�17 19.�0� PP05010�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 0.866 1�.756 �7.87� PP05010�15
1�" 1�.976 (�55mm) 1�.976 1.�68 1.�96 15.157 ��.60� PP05010�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 1.61� 17.��� 6�.7�� PP05010�00
Z
D
Le
S
r=d
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
71.05�609
ChemicalProcess Piping Systems - Dimensional Data
Elbow 90° - Extended leg
Description: Elbow 90° - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 �.087 �.071 0.0�6 PP051500�0
¾" 0.98� (�5mm) 0.98� 0.091 �.��� �.�07 0.07� PP051500�5
1" 1.�60 (��mm) 1.�60 0.11� �.795 �.016 0.1�6 PP051500��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.91� �.�91 0.��0 PP051500�0
1½" 1.969 (50mm) 1.969 0.181 �.��8 �.�09 0.�65 PP05150050
�" �.�80 (6�mm) �.�80 0.��8 �.��8 �.7�� 0.587 PP0515006�
�½" �.95� (75mm) �.95� 0.�68 �.58� 5.�5� 0.906 PP05150075
�" �.5�� (90mm) �.5�� 0.��� �.6�� 5.7�8 1.�75 PP05150090
�" �.��1 (110mm) �.��1 0.�9� �.976 6.�96 �.�88 PP05150110
�½" �.9�1 (1�5mm) �.9�1 0.��9 �.016 6.890 �.508 PP051501�5
5" 5.51� (1�0mm) 5.51� 0.500 �.76� 8.0�1 �.070 PP051501�0
6" 6.�99 (160mm) 6.�99 0.575 5.6�0 9.�70 7.1�8 PP05150160
7" 7.087 (180mm) 7.087 0.6�6 5.591 9.7�� 9.�51 PP05150180
8" 7.87� (�00mm) 7.87� 0.717 6.0�� 10.�15 1�.�19 PP05150�00
9" 8.858 (��5mm) 8.858 0.807 6.06� 11.06� 16.��� PP05150��5
10" 9.8�� (�50mm) 9.8�� 0.89� 5.��6 11.�96 19.�9� PP05150�50
11" 11.0�� (�80mm) 11.0�� 1.000 5.669 1�.598 �6.906 PP05150�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 6.06� 1�.567 �8.65� PP05150�15
Z
D
Le
S
8
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Elbow 45° - Extended leg
Description: Elbow 45° - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 �.0�7 �.87� 0.0�8 PP051600�0
¾" 0.98� (�5mm) 0.98� 0.091 �.��� �.150 0.077 PP051600�5
1" 1.�60 (��mm) 1.�60 0.11� �.795 �.858 0.1�9 PP051600��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.87� �.1�� 0.��0 PP051600�0
1½" 1.969 (50mm) 1.969 0.181 �.��1 �.�5� 0.�6� PP05160050
�" �.�80 (6�mm) �.�80 0.��8 �.598 �.5�8 0.�77 PP0516006�
�½" �.95� (75mm) �.95� 0.�68 �.795 5.079 0.6�8 PP05160075
�" �.5�� (90mm) �.5�� 0.��� �.�68 5.51� 0.990 PP05160090
�" �.��1 (110mm) �.��1 0.�9� �.661 6.�99 1.705 PP05160110
�½" �.9�1 (1�5mm) �.9�1 0.��9 �.858 6.65� �.�6� PP051601�5
5" 5.51� (1�0mm) 5.51� 0.500 �.80� 7.95� �.90� PP051601�0
6" 6.�99 (160mm) 6.�99 0.575 5.6�0 9.055 5.��� PP05160160
7" 7.087 (180mm) 7.087 0.6�6 5.6�0 9.��9 7.06� PP05160180
8" 7.87� (�00mm) 7.87� 0.717 6.0�� 10.��6 10.175 PP05160�00
9" 8.858 (��5mm) 8.858 0.807 6.0�� 10.8�7 1�.�10 PP05160��5
10" 9.8�� (�50mm) 9.8�� 0.89� 5.�76 11.�96 17.�58 PP05160�50
11" 11.0�� (�80mm) 11.0�� 1.000 5.6�0 1�.598 ��.�7� PP05160�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 6.10� 1�.567 �5.718 PP05160�15
Z
D
Le
ZLeS
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
91.05�609
ChemicalProcess Piping Systems - Dimensional Data
Tee
Description: Tee PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S L L1 Z Weight Part
Size Size in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 �.071 0.��� 1.�96 0.055 PP050�00�0
¾" 0.98� (�5mm) 0.98� 0.091 �.�68 0.��� 1.65� 0.07� PP050�00�5
1" 1.�60 (��mm) 1.�60 0.11� �.��5 0.��� 1.7�� 0.106 PP050�00��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.6�� 0.��� 1.811 0.156 PP050�00�0
1½" 1.969 (50mm) 1.969 0.181 �.9�7 0.�7� 1.969 0.�57 PP050�0050
�" �.�80 (6�mm) �.�80 0.��8 5.0�9 0.669 �.6�8 0.5�� PP050�006�
�½" �.95� (75mm) �.95� 0.�68 5.906 0.7�8 �.99� 0.8�7 PP050�0075
�" �.5�� (90mm) �.5�� 0.��� 7.�05 1.5�5 �.055 1.�09 PP050�0090
�" �.��1 (110mm) �.��1 0.�9� 10.0�9 �.165 5.157 �.871 PP050�0110
�½" �.9�1 (1�5mm) �.9�1 0.��9 9.8�� 1.969 5.157 �.586 PP050�01�5
5" 5.51� (1�0mm) 5.51� 0.500 1�.�6� �.�6� 6.�60 5.�79 PP050�01�0
6" 6.�99 (160mm) 6.�99 0.575 1�.��1 �.165 6.�78 7.��9 PP050�0160
7" 7.087 (180mm) 7.087 0.6�6 16.9�9 �.6�� 8.�65 1�.��� PP050�0180
8" 7.87� (�00mm) 7.87� 0.717 17.1�6 �.�65 8.701 1�.916 PP050�0�00
9" 8.858 (��5mm) 8.858 0.807 17.717 �.8�5 8.9�7 �0.��0 PP050�0��5
10" 9.8�� (�50mm) 9.8�� 0.89� 17.6�8 �.5�0 8.9�7 ��.100 PP050�0�50
11" 11.0�� (�80mm) 11.0�� 1.000 �0.669 �.��8 10.51� ��.660 PP050�0�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 ��.�8� �.��8 11.1�� �5.��0 PP050�0�15
1�" 1�.976 (�55mm) 1�.976 1.�68 �7.��� �.9�7 1�.7�0 68.��0 PP050�0�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 �8.5�� �.016 1�.17� 8�.600 PP050�0�00
18" 17.717 (�50mm) 17.717 1.610 ��.95� 5.�15 16.�96 1��.000 PP050�0�50
�0" 19.685 (500mm) 19.685 1.787 �6.61� 6.�99 18.110 171.600 PP050�0500
ZD
L1
L
S
10
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Tee: Reduced
Description: Tee: Reduced PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Fabricated
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D1 d2 S1 S2 L L1 L2 z1 z2 Weight Part
Size Size in in in in in in in in in lbs Number
�" x 1" �.5�� (90mm) x 1.�60 (��mm) �.5�� 1.�60 0.��� 0.11� 7.99� �.087 0.906 �.016 �.��6 1.��� PP050�0900��
�" x 1" �.��1 (110mm) x 1.�60 (��mm) �.��1 1.�60 0.�9� 0.11� 9.�1� �.598 0.866 �.606 �.58� �.068 PP050�1100��
�" x 1½" �.��1 (110mm) x 1.969 (50mm) �.��1 1.969 0.�9� 0.181 9.��9 �.598 1.06� �.606 �.976 �.068 PP050�110050
�½" x �" �.9�1 (1�5mm) x �.�80 (6�mm) �.9�1 �.�80 0.�9� 0.��8 10.�9� �.756 1.��0 5.197 �.��1 �.080 PP050�1�506�
�½" x �" �.9�1 (1�5mm) x �.5�� (90mm) �.9�1 �.5�� 0.��9 0.��� 10.�9� 1.77� 1.65� 5.197 �.8�� �.5�0 PP050�1�5090
5" x �" 5.51� (1�0mm) x �.�80 (6�mm) 5.51� �.�80 0.500 0.��8 11.�57 �.�68 1.�60 5.7�8 �.7�� �.1�6 PP050�1�006�
5" x �" 5.51� (1�0mm) x �.5�� (90mm) 5.51� �.5�� 0.500 0.��� 11.�57 �.189 1.61� 5.7�8 5.118 �.��� PP050�1�0090
5" x �½" 5.51� (1�0mm) x �.95� (75mm) 5.51� �.95� 0.500 0.�68 11.�57 �.189 1.�78 5.7�8 5.118 �.9�8 PP050�1�0075
5" x �" 5.51� (1�0mm) x �.��1 (110mm) 5.51� �.��1 0.500 0.�9� 11.�57 1.969 1.7�� 5.7�8 5.51� �.9�8 PP050�1�0110
5" x �½" 5.51� (1�0mm) x �.9�1 (1�5mm) 6.�99 �.9�1 0.575 0.��9 1�.�0� �.�8� 1.850 6.��0 5.906 6.556 PP050�1601�5
6" x �" 6.�99 (160mm) x �.�80 (6�mm) 7.087 �.�80 0.6�6 0.��8 1�.701 �.9�1 1.181 6.850 5.51� 7.��8 PP050�18006�
6" x �½" 6.�99 (160mm) x �.95� (75mm) 7.087 �.95� 0.6�6 0.�68 1�.701 �.�09 1.181 6.850 6.�99 7.700 PP050�180075
7" x �" 7.087 (180mm) x �.��1 (110mm) 7.087 �.��1 0.6�6 0.�9� 1�.701 �.6�� 1.969 6.850 5.906 8.580 PP050�180110
8" x �" 7.87� (�00mm) x �.�80 (6�mm) 7.87� �.�80 0.717 0.��8 15.0�9 5.6�0 1.��0 7.5�0 5.709 10.��0 PP050��0006�
8" x �" 7.87� (�00mm) x �.5�� (90mm) 7.87� �.5�� 0.717 0.��� 15.�5� �.961 1.575 7.677 6.�78 9.9�� PP050��00090
8" x �" 7.87� (�00mm) x �.��1 (110mm) 7.87� �.��1 0.717 0.�9� 15.�5� �.80� 1.575 7.677 6.�99 9.856 PP050��00110
8" x �½" 7.87� (�00mm) x �.9�1 (1�5mm) 7.87� �.9�1 0.717 0.��9 15.�5� �.�88 1.69� 7.677 6.�96 1�.�76 PP050��001�5
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� 6.�99 0.717 0.575 15.�5� �.858 �.�6� 6.�96 7.087 10.560 PP050��00160
10" x 6" 9.8�� (�50mm) x 6.�99 (160mm 9.8�� 6.�99 0.89� 0.575 17.��� �.��1 �.�8� 8.661 8.�86 17.�58 PP050��50160
10" x �" 9.8�� (�50mm) x �.��1 (110mm) 9.8�� �.��1 0.89� 0.�9� 17.��1 5.�15 1.�99 8.7�0 7.677 17.600 PP050��50160
z2
z1
D1
d2
L1
L2
L
S2
S1
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
111.05�609
ChemicalProcess Piping Systems - Dimensional Data
Tee - Extended leg
Description: Tee - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S L L1 Z Weight Part
Size Size in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 1.61� �.�5� �.1�6 0.0�� PP05��00�0
¾" 0.98� (�5mm) 0.98� 0.091 1.61� �.80� �.�6� 0.088 PP05��00�5
1" 1.�60 (��mm) 1.�60 0.11� 1.811 5.��� �.6�8 0.15� PP05��00��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.0�7 6.�78 �.��8 0.�5� PP05��00�0
1½" 1.969 (50mm) 1.969 0.181 �.��� 7.��� �.6�� 0.��0 PP05��0050
�" �.�80 (6�mm) �.�80 0.��8 �.6�8 8.��6 �.�5� 0.81� PP05��006�
�½" �.95� (75mm) �.95� 0.�68 �.8�5 9.685 �.80� 1.�86 PP05��0075
�" �.5�� (90mm) �.5�� 0.��� �.150 11.06� 5.��� �.01� PP05��0090
�" �.��1 (110mm) �.��1 0.�9� �.�65 1�.6�8 6.�78 �.619 PP05��0110
�½" �.9�1 (1�5mm) �.9�1 0.��9 �.858 1�.780 6.9�9 �.86� PP05��01�5
5" 5.51� (1�0mm) 5.51� 0.500 �.09� 15.709 7.87� 5.676 PP05��01�0
6" 6.�99 (160mm) 6.�99 0.575 �.09� 16.�60 8.110 9.0�� PP05��0160
7" 7.087 (180mm) 7.087 0.6�6 5.6�0 �0.787 10.��6 1�.9�8 PP05��0180
8" 7.87� (�00mm) 7.87� 0.717 �.88� 19.88� 9.961 16.5�� PP05��0�00
9" 8.858 (��5mm) 8.858 0.807 5.079 ��.008 10.9�5 ��.9�� PP05��0��5
10" 9.8�� (�50mm) 9.8�� 0.89� 5.197 ��.91� 11.��9 ��.860 PP05��0�50
11" 11.0�� (�80mm) 11.0�� 1.000 5.�76 ��.76� 1�.1�6 ��.670 PP05��0�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 6.06� �7.6�8 1�.6�� ��.��0 PP05��0�15
Z
D
L1
L
S
1�
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Tee: Reduced - Extended leg
Description: Tee: Reduced - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
z2
z1
D1
D2
L1
L2
L
S2
S1
PN 10 / SDR 11
Nominal Actual OD D1 D2 S1 S2 L L1 L2 z1 z2 Weight Part
Size Size in in in in in in in in in lbs Number
�" x 1½" �.�80 (6�mm) x 1.969 (50mm) �.�80 1.969 0.��8 0.181 8.�65 �.�80 �.�05 �.�5� �.055 0.660 PP05��06�050
�½" x 1" �.95� (75mm) x 1.�60 _��mm) �.95� 1.�60 0.�68 0.11� 10.079 �.756 1.811 5.0�9 �.�5� 1.078 PP05��0750��
�½" x 1½" �.95� (75mm) x 1.969 (50mm) �.95� 1.969 0.�68 0.181 9.961 �.756 �.�05 5.000 �.��9 1.188 PP05��075050
�½" x �" �.95� (75mm) x �.�80 (6�mm) �.95� �.�80 0.�68 0.��8 10.0�9 �.756 �.�80 5.0�9 �.606 1.��� PP05��07506�
�" x 1½" �.5�� (90mm) x 1.969 (50mm) �.5�� 1.969 0.��� 0.181 10.709 �.110 �.�8� 5.�15 �.606 1.�96 PP05��090050
�" x �" �.5�� (90mm) x �.�80 (6�mm) �.5�� �.�80 0.��� 0.��8 10.709 �.110 �.559 5.�15 �.8�� 1.716 PP05��09006�
�" x �½" �.5�� (90mm) x �.95� (75mm) �.5�� �.95� 0.��� 0.�68 10.709 �.87� �.677 5.�5� 5.��� 1.760 PP05��090075
�" x �" �.��1 (110mm) x �.�80 (6�mm) �.��1 �.�80 0.�9� 0.��8 1�.598 �.��5 �.559 6.�60 5.787 �.750 PP05��11006�
�" x �½" �.��1 (110mm) x �.95� (75mm) �.��1 �.95� 0.�9� 0.�68 1�.165 �.��8 �.756 6.10� 5.9�5 �.�00 PP05��110075
�" x �" �.��1 (110mm) x �.5�� (90mm) �.��1 �.5�� 0.�9� 0.��� 1�.5�0 �.�86 �.150 6.�60 6.��0 �.168 PP05��110090
�½" x �" �.9�1 (1�5mm) x �.��1 (110mm) �.9�1 �.��1 0.��9 0.�9� 1�.��5 �.5�� �.�68 6.7�� 6.69� �.09� PP05��1�5110
6" x �" 6.�99 (160mm) x �.�80 (6�mm) 6.�99 �.�80 0.575 0.��8 1�.50� �.858 �.559 6.77� 6.9�9 5.896 PP05��16006�
6" x �½" 6.�99 (160mm) x x �.95� (75mm) 6.�99 �.95� 0.575 0.�68 1�.50� �.858 �.91� 6.77� 7.087 5.808 PP05��160075
6" x �" 6.�99 (160mm) x �.5�� (90mm) 6.�99 �.5�� 0.575 0.��� 16.06� �.976 �.110 8.071 7.�0� 5.896 PP05��160090
6" x �" 6.�99 (160mm) x �.��1 (110mm) 6.�99 �.��1 0.575 0.�9� 16.06� �.976 �.��6 8.071 7.677 7.�60 PP05��160110
7" x 6" 7.087 (180mm) x 6.�99 (160mm) 7.087 6.�99 0.6�6 0.575 16.181 �.1�� �.701 8.110 8.071 9.�60 PP05��180160
8" x �½" 7.87� (�00mm) x �.95� (75mm) 7.87� �.�80 0.717 0.��8 19.606 �.�09 �.�80 9.80� 7.�80 1�.5�0 PP05���0006�
8" x �" 7.87� (�00mm) x �.5�� (90mm) 7.87� �.5�� 0.717 0.��� 19.606 �.�09 �.110 9.80� 8.150 1�.�10 PP05���00090
8" x �" 7.87� (�00mm) x �.��1 (110mm) 7.87� �.��1 0.717 0.�9� 19.606 �.�09 �.��8 9.80� 8.�65 15.�88 PP05���00110
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� 6.�99 0.717 0.575 19.606 �.�09 �.858 9.80� 9.�1� 18.�60 PP05���00160
9" x �½" 8.858 (��5mm) x �.95� (75mm) 8.858 �.95� 0.807 0.�68 17.�6� �.7�� �.95� 8.701 8.9�7 1�.080 PP05����5075
9" x �" 8.858 (��5mm) x �.5�� (90mm) 8.858 �.5�� 0.807 0.��� �1.850 5.000 �.150 10.866 8.898 �0.6�6 PP05����5090
9" x �" 8.858 (��5mm) x �.��1 (110mm) 8.858 �.��1 0.807 0.�9� �1.850 5.000 �.��6 10.866 9.�5� 1�.5�0 PP05����5110
9" x 6" 8.858 (��5mm) x 6.�99 (160mm) 8.858 6.�99 0.807 0.575 �1.850 5.000 �.1�� 10.866 10.0�9 17.��8 PP05����5160
9" x 7" 8.858 (��5mm) x 7.087 (180mm) 8.858 7.087 0.807 0.6�6 �1.�78 5.197 5.197 10.709 10.906 �0.988 PP05����5180
10" x �" 9.8�� (�50mm) x �.��1 (110mm) 9.8�� �.��1 0.89� 0.�9� ��.6�8 5.118 �.��8 11.��9 9.5�8 - PP05���50110
10" x 6" 9.8�� (�50mm) x 6.�99 (160mm) 9.8�� 6.�99 0.89� 0.575 ��.6�8 5.118 �.858 11.��9 10.�76 - PP05���50160
1�" x �" 1�.�0� (�15mm) x �.��1 (110mm) 1�.�0� �.��1 1.1�6 0.�9� �7.�6� 5.906 �.��8 1�.6�� 10.906 - PP05���15110
1�" x 6" 1�.�0� (�15mm) x 6.�99 (160mm) 1�.�0� 6.�99 1.1�6 0.575 �7.�6� 5.906 �.016 1�.6�� 11.�17 - PP05���15160
1�" x 10" 1�.�0� (�15mm) x 9.8�� (�50mm) 1�.�0� 9.8�� 1.1�6 0.89� �7.�6� 5.906 5.118 1�.6�� 1�.795 - PP05���15�50
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1�1.05�609
ChemicalProcess Piping Systems - Dimensional Data
Reducer
Description: Reducer PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
D1D2
L1
L2
L
S2S1
PN 10 / SDR 11
Nominal Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in Lbs Number
¾" x ½" 0.98� (�5mm) x 0.787 (�0mm) 0.98� 0.787 0.091 0.075 �.677 0.787 0.787 0.011 PP050�0�50�0
1" x ½" 1.�60 (��mm) x 0.787 (�0mm) 1.�60 0.787 0.11� 0.075 �.677 0.787 0.787 0.0�� PP050�0�60�0
1" x ¾" 1.�60 (��mm) x 0.98� (�5mm) 1.�60 0.98� 0.11� 0.091 �.677 0.787 0.787 0.0�� PP050�0��0�5
1¼" x ½" 1.575 (�0mm) x 0.787 (�0mm) 1.575 0.787 0.1�6 0.075 1.969 0.709 0.51� 0.0�� PP050�0�00�0
1¼" x ¾" 1.575 (�0mm) x 0.98� (�5mm) 1.575 0.98� 0.1�6 0.091 �.��1 0.787 0.787 0.0�7 PP050�0�00�5
1¼" x 1" 1.575 (�0mm) x 1.�60 (��mm) 1.575 1.�60 0.1�6 0.11� �.��1 0.787 0.787 0.0�� PP050�0�00��
1½" x ¾" 1.969 (50mm) x 0.98� (�5mm) 1.969 0.98� 0.181 0.091 1.969 0.98� 1.06� 0.05� PP050�0500�5
1½" x 1" 1.969 (50mm) x 1.�60 (��mm) 1.969 1.�60 0.181 0.11� 1.969 1.06� 1.06� 0.057 PP050�0500��
1½" x 1¼" 1.969 (50mm) x 1.575 (�0mm) 1.969 1.575 0.181 0.1�6 1.969 1.181 1.0�� 0.06� PP050�0500�0
�" x 1" �.�80 (6�mm) x 1.�60 (��mm) �.�80 1.�60 0.��8 0.11� �.�6� 1.06� 0.98� 0.10� PP050�06�0��
�" x 1¼" �.�80 (6�mm) x 1.575 (�0mm) �.�80 1.575 0.��8 0.1�6 �.�6� 1.10� 1.06� 0.11� PP050�06�0�0
�" x 1½" �.�80 (6�mm) x 1.969 (50mm) �.�80 1.969 0.��8 0.181 �.�6� 1.1�� 1.06� 0.1�0 PP050�06�050
�½" x 1" �.95� (75mm) x 1.�60 (��mm) �.95� 1.�60 0.�68 0.11� �.756 0.98� 0.�9� 0.1�� PP050�0750��
�½" x 1¼" �.95� (75mm) x 1.575 (�0mm) �.95� 1.575 0.�68 0.1�6 �.756 1.181 0.98� 0.165 PP050�0750�0
�½" x 1½" �.95� (75mm) x 1.969 (50mm) �.95� 1.969 0.�68 0.181 �.756 1.181 1.10� 0.161 PP050�075050
�½" x �" �.95� (75mm) x �.�80 (6�mm) �.95� �.�80 0.�68 0.��8 �.��8 0.98� 1.0�� 0.1�8 PP050�07506�
�" x 1½" �.5�� (90mm) x 1.969 (50mm) �.5�� 1.969 0.��� 0.181 �.91� 0.866 0.787 0.�6� PP050�090050
�" x �" �.5�� (90mm) x �.�80 (6�mm) �.5�� �.�80 0.��� 0.��8 �.91� 1.181 1.10� 0.�8� PP050�09006�
�" x �½" �.5�� (90mm) x �.95� (75mm) �.5�� �.95� 0.��� 0.�68 �.91� 1.��0 1.0�� 0.�1� PP050�090075
�" x 1½" �.��1 (110mm) x 1.969 (50mm) �.��1 1.969 0.�9� 0.181 �.5�� 1.10� 0.787 0.��� PP050�110050
�" x �" �.��1 (110mm) x �.�80 (6�mm) �.��1 �.�80 0.�9� 0.��8 �.1�� 1.61� 1.�78 0.585 PP050�11006�
�" x �½" �.��1 (110mm) x �.95� (75mm) �.��1 �.95� 0.�9� 0.�68 �.5�� 1.65� 1.0�� 0.�75 PP050�110075
�" x �" �.��1 (110mm) x �.5�� (90mm) �.��1 �.5�� 0.�9� 0.��� �.9�7 1.61� 1.575 0.6�7 PP050�110090
�½" x �" �.9�1 (1�5mm) x �.�80 (6�mm)) �.9�1 �.�80 0.��9 0.��8 �.7�� 1.�60 0.6�0 0.79� PP050�1�1506
�½" x �½" �.9�1 (1�5mm) x �.95� (75mm) �.9�1 �.95� 0.��9 0.�68 �.858 1.�60 0.7�8 0.660 PP050�1�5075
�½" x �" �.9�1 (1�5mm) x �.5�� (90mm) �.9�1 �.5�� 0.��9 0.��� �.��1 1.61� 1.61� 0.8�6 PP050�1�5090
�½" x �" �.9�1 (1�5mm) x �.��1 (110mm) �.9�1 �.��1 0.��9 0.�9� �.9�7 1.�60 1.10� 0.8�� PP050�1�5110
(Continued on Next Page)
1�
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Reducer
Description: Reducer PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
D1D2
L1
L2
L
S2S1
PN 10 / SDR 11
Nominal Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in Lbs Number
5" x �½" 5.51� (1�0mm) x �.95� (75mm) 5.51� �.95� 0.500 0.�68 5.�15 1.�78 0.7�8 0.5�8 PP050�1�0075
5" x �" 5.51� (1�0mm) x �.5�� (90mm) 5.51� �.5�� 0.500 0.��� 5.118 1.�78 0.866 0.57� PP050�1�0090
5" x �" 5.51� (1�0mm) x �.��1 (110mm) 5.51� �.��1 0.500 0.�9� �.7�� 1.�78 1.10� 0.506 PP050�1�0110
5" x �" 5.51� (1�0mm) x �.9�1 (1�5mm) 5.51� �.9�1 0.500 0.��9 �.7�� 1.�78 1.�60 0.5�8 PP050�1�01�5
6" x �" 6.�99 (160mm) x �.5�� (90mm) 6.�99 �.5�� 0.575 0.��� 5.��� �.008 1.65� 1.56� PP050�160090
6" x �" 6.�99 (160mm) x �.��1 (110mm) 6.�99 �.��1 0.575 0.�9� 5.0�9 �.008 1.575 1.58� PP050�160110
6" x �½" 6.�99 (160mm) x �.9�1 (1�5mm) 6.�99 �.9�1 0.575 0.��9 �.80� �.008 1.65� 1.57� PP050�1601�5
6" x 5" 6.�99 (160mm) x 5.51� (1�0mm) 6.�99 5.51� 0.575 0.500 �.7�� �.0�7 1.850 1.617 PP050�1601�0
7" x �" 7.087 (180mm) x �.5�� (90mm) 7.087 �.5�� 0.6�6 0.��� 5.709 1.77� 0.866 1.188 PP050�180090
7" x �" 7.087 (180mm) x �.��1 (110mm) 7.087 �.��1 0.6�6 0.�9� 5.906 1.77� 1.10� 1.166 PP050�180110
7" x �½" 7.087 (180mm) x �.9�1 (1�5mm) 7.087 �.9�1 0.6�6 0.��9 5.6�0 �.008 1.65� 1.078 PP050�1801�5
7" x 5" 7.087 (180mm) x 5.51� (1�0mm) 7.087 5.51� 0.6�6 0.500 5.�15 1.77� 1.�78 1.01� PP050�1801�0
7" x 6" 7.087 (180mm) x 6.�99 (160mm) 7.087 6.�99 0.6�6 0.575 5.51� 1.77� 1.575 1.01� PP050�180160
8" x 5" 7.87� (�00mm) x 5.51� (1�0mm) 7.87� 5.51� 0.717 0.500 5.709 �.�80 1.69� 1.��0 PP050���01�0
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� 6.�99 0.717 0.575 5.709 �.�80 1.969 �.816 PP050���0160
8" x 7" 7.87� (�00mm) x 7.087 (180mm) 7.87� 7.087 0.717 0.6�6 5.709 1.969 1.77� 1.188 PP050���0180
9" x 5" 8.858 (��5mm) x 5.51� (1�0mm) 8.858 5.51� 0.807 0.500 5.906 �.�0� 1.890 �.��1 PP050���51�0
9" x 6" 8.858 (��5mm) x 6.�99 (160mm) 8.858 6.�99 0.807 0.575 6.�99 �.559 �.1�6 �.619 PP050���5160
9" x 7" 8.858 (��5mm) x 7.087 (180mm) 8.858 7.087 0.807 0.6�6 6.�99 �.165 �.�8� �.850 PP050���5180
9" x 8" 8.858 (��5mm) x 7.87� (�00mm) 8.858 7.87� 0.807 0.717 6.�99 �.165 1.969 1.5�0 PP050���5�00
10" x 6" 9.8�� (�50mm) x 6.�99 (160mm 9.8�� 6.�99 0.89� 0.575 6.69� �.�80 �.087 �.7�0 PP050��50160
10" x 7" 9.8�� (�50mm) x 7.087 (180mm) 9.8�� 7.087 0.89� 0.6�6 6.890 �.5�0 �.�8� 5.0�7 PP050��50180
10" x 8" 9.8�� (�50mm) x 7.87� (�00mm) 9.8�� 7.87� 0.89� 0.717 7.087 �.5�0 �.5�0 5.500 PP050��50�00
10" x 9" 9.8�� (�50mm) x 8.858 (��5mm) 9.8�� 8.858 0.89� 0.807 7.087 �.�6� �.165 6.050 PP050��50��5
11" x 8" 11.0�� (�80mm) x 7.87� (�00mm) 11.0�� 7.87� 1.000 0.717 8.071 �.756 1.969 7.�16 PP050��80�00
11" x 9" 11.0�� (�80mm) x 8.858 (��5mm) 11.0�� 8.858 1.000 0.807 7.99� �.8�5 �.��� 8.�7� PP050��80��5
11" x 10" 11.0�� (�80mm) x 9.8�� (�50mm) 11.0�� 9.8�� 1.000 0.89� 7.95� �.8�5 �.��1 8.096 PP050��80�50
(Continued on Next Page)
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
151.05�609
ChemicalProcess Piping Systems - Dimensional Data
Reducer
Description: Reducer PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Machined
Connection: Butt Fusion
D1D2
L1
L2
L
S2S1
PN 10 / SDR 11
Nominal Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in Lbs Number
1�"x 8" 1�.�0� (�15mm) x 7.87� (�00mm) 1�.�0� 7.87� 1.1�6 0.717 9.7�� �.150 1.969 9.9�� PP050��15�00
1�"x 9" 1�.�0� (�15mm) x 8.858 (��5mm) 1�.�0� 8.858 1.1�6 0.807 9.��1 �.�07 �.�6� 10.�7� PP050��15��5
1�" x 10" 1�.�0� (�15mm) x 9.8�� (�50mm) 1�.�0� 9.8�� 1.1�6 0.89� 9.09� �.�86 �.�80 11.000 PP050��15�50
1�" x 11" 1�.�0� (�15mm) x 11.0�� (�80mm) 1�.�0� 11.0�� 1.1�6 1.000 8.7�0 �.150 �.756 11.70� PP050��15�80
1�" x 9" 1�.976 (�55mm) x 8.858 (��5mm) 1�.976 8.858 1.�68 0.807 9.6�6 �.5�� �.165 9.�7� PP050��55��5
1�" x 10" 1�.976 (�55mm) x 9.8�� (�50mm) 1�.976 9.8�� 1.�68 0.89� 9.6�6 �.5�� �.�6� 8.668 PP050��55�50
1�" x 11" 1�.976 (�55mm) x 11.0�� (�80mm) 1�.976 11.0�� 1.�68 1.000 9.6�6 �.5�� �.756 8.18� PP050��55�80
1�" x 1�" 1�.976 (�55mm) x 1�.�0� (�15mm) 1�.976 1�.�0� 1.�68 1.1�6 9.6�6 �.5�� �.150 7.788 PP050��55�15
16" x 9" 15.7�8 (�00mm) x 8.858 (��5mm) 15.7�8 9.8�� 0.89� 0.559 10.��6 �.7�0 �.756 9.680 PP050��00��5
16" x 10" 15.7�8 (�00mm) x 9.8�� (�50mm) 15.7�8 11.0�� 0.89� 0.6�6 10.��6 �.7�0 �.756 9.0�0 PP050��00�50
16" x 11" 15.7�8 (�00mm) x 11.0�� (�80mm) 15.7�8 1�.�0� 0.89� 0.705 10.��6 �.7�0 �.150 7.9�0 PP050��00�80
16" x 1�" 15.7�8 (�00mm) x 1�.�0� (�15mm) 15.7�8 1�.976 0.89� 0.791 10.��6 �.7�0 �.5�� 6.8�0 PP050��00�15
16" x 1�" 15.7�8 (�00mm) x 1�.976 (�55mm) 17.717 11.0�� 1.00� 0.6�6 9.055 �.�6� �.756 1�.�00 PP050��00�55
18" x 11" 17.717 (�50mm) x 11.0�� (�80mm) 17.717 1�.�0� 1.00� 0.705 9.055 �.�6� �.150 11.880 PP050��50�80
18" x 1�" 17.717 (�50mm) x 1�.�0� (�15mm) 17.717 1�.976 1.00� 0.791 9.055 �.�6� �.5�� 11.000 PP050��50�15
18" x 1�" 17.717 (�50mm) x 1�.976 (�55mm) 17.717 15.7�8 1.00� 0.89� 9.055 �.�6� �.7�0 9.680 PP050��50�55
18" x 16" 17.717 (�50mm) x 15.7�8 (�00mm) 19.685 1�.�0� 1.118 0.705 9.055 �.�6� �.150 17.8�0 PP050��50�00
�0" x 1�" 19.685 (500mm) x 1�.�0� (�15mm) 19.685 1�.976 1.118 0.791 9.055 �.�6� �.5�� 16.060 PP050�500�15
�0" x 1�" 19.685 (500mm) x 1�.976 (�55mm) 19.685 15.7�8 1.118 0.89� 9.055 �.�6� �.7�0 1�.7�0 PP050�500�55
�0" x 16" 19.685 (500mm) x 15.7�8 (�00mm) 19.685 17.717 1.118 1.00� 9.055 �.�6� �.�6� 1�.100 PP050�500�00
�0" x 16" 19.685 (500mm) x 17.717 (�50mm) ��.0�7 15.7�8 1.��8 0.89� 9.055 �.�6� �.7�0 �1.780 PP050�500�50
��" x 16" ��.0�7 (560mm) x 15.7�8 (�00mm) ��.0�7 17.717 1.��8 1.00� 7.87� �.�6� �.�6� 18.9�0 PP050�560�00
��" x 18" ��.0�7 (560mm) x 17.717 (�50mm) ��.0�7 19.685 1.��8 1.118 7.87� �.�6� �.�6� 16.7�0 PP050�560�50
��" x �0" ��.0�7 (560mm) x 19.685 (500mm) ��.80� 15.7�8 1.�06 0.89� 9.055 �.�6� �.7�0 ��.��0 PP050�560500
��" x 16" ��.80� (6�0mm) x 15.7�8 (�00mm) ��.80� 17.717 1.�06 1.00� 7.87� �.�6� �.�6� �0.1�0 PP050�6�0�00
��" x 18" ��.80� (6�0mm) x 17.717 (�50mm) ��.80� 19.685 1.�06 1.118 7.87� �.�6� �.�6� �6.�00 PP050�6�0�50
��" x �0" ��.80� (6�0mm) x 19.685 (500mm) ��.80� ��.0�7 1.�06 1.��8 7.87� �.�6� �.�6� �1.560 PP050�6�0500
��" x ��" ��.80� (6�0mm) x ��.0�7 (560mm) �7.95� 19.685 1.58� 1.118 7.�80 �.�07 1.575 �1.800 PP050�6�0560
16
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Reducer: Concentric - Extended leg
Description: Reducer: Concentric - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nom. Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in lbs Number
¾" x ½" 0.98� (�5mm) x 0.787 (�0mm) 0.98� 0.787 0.091 0.075 �.��6 1.61� 1.�57 0.0�0 PP05190�50�0
1" x ½" 1.�60 (��mm) x 0.787 (�0mm) 1.�60 0.787 0.11� 0.075 �.9�7 1.7�� 1.�57 0.05� PP05190��0�0
1" x ¾" 1.�60 (��mm) x 0.98� (�5mm) 1.�60 0.98� 0.11� 0.091 �.9�7 1.7�� 1.61� 0.06� PP05190��0�5
1¼" x ½" 1.575 (�0mm) x 0.787 (�0mm) 1.575 0.787 0.1�6 0.075 �.09� 1.9�9 1.77� 0.077 PP05190�00�0
1¼" x ¾" 1.575 (�0mm) x 0.98� (�5mm) 1.575 0.98� 0.1�6 0.091 �.09� 1.9�9 1.61� 0.088 PP05190�00�5
1¼" x 1" 1.575 (�0mm) x 1.�60 (��mm) 1.575 1.�60 0.1�6 0.11� �.1�� 1.9�9 1.7�� 0.088 PP05190�00��
1½" x ¾" 1.969 (50mm) x 0.98� (�5mm) 1.969 0.98� 0.181 0.091 5.118 �.�05 1.7�� 0.1�8 PP05190500�5
1½" x 1" 1.969 (50mm) x 1.�60 (��mm) 1.969 1.�60 0.181 0.11� 5.197 �.��� 1.850 0.1�� PP05190500��
1½" x 1¼" 1.969 (50mm) x 1.575 (�0mm) 1.969 1.575 0.181 0.1�6 5.�76 �.�05 �.0�7 0.16� PP05190500�0
�" x 1" �.�80 (6�mm) x 1.�60 (��mm) �.�80 1.�60 0.��8 0.11� 5.591 �.�80 1.811 0.��0 PP051906�0��
�" x 1¼" �.�80 (6�mm) x 1.575 (�0mm) �.�80 1.575 0.��8 0.1�6 5.787 �.5�0 �.0�7 0.�6� PP051906�0�0
�" x 1½" �.�80 (6�mm) x 1.969 (50mm) �.�80 1.969 0.��8 0.181 5.98� �.5�0 �.�8� 0.�08 PP051906�050
�½" x 1½" �.95� (75mm) x 1.969 (50mm) �.95� 1.969 0.�68 0.181 5.906 �.559 �.��� 0.�96 PP0519075050
�½" x �" �.95� (75mm) x �.�80 (6�mm) �.95� �.�80 0.�68 0.��8 6.5�5 �.756 �.559 0.�18 PP051907506�
�" x 1½" �.5�� (90mm) x 1.969 (50mm) �.5�� 1.969 0.��� 0.181 6.850 �.150 �.��� 0.651 PP0519090050
�" x �" �.5�� (90mm) x �.�80 (6�mm) �.5�� �.�80 0.��� 0.��8 7.165 �.189 �.677 0.7�8 PP051909006�
�" x �½" �.5�� (90mm) x �.95� (75mm) �.5�� �.95� 0.��� 0.�68 7.�8� �.110 �.99� 0.660 PP0519090075
�" x �" �.��1 (110mm) x �.�80 (6�mm) �.��1 �.�80 0.�9� 0.��8 7.�8� �.�07 �.598 0.990 PP051911006�
�" x �½" �.��1 (110mm) x �.95� (75mm) �.��1 �.95� 0.�9� 0.�68 7.�8� �.�68 �.87� 1.0�� PP0519110075
�" x �" �.��1 (110mm) x �.5�� (90mm) �.��1 �.5�� 0.�9� 0.��� 7.�8� �.�07 �.150 1.166 PP0519110090
�½" x �" �.9�1 (1�5mm) x �.�80 (6�mm)) �.9�1 �.�80 0.��9 0.��8 7.87� �.58� �.110 1.��0 PP05191�506�
�½" x �" �.9�1 (1�5mm) x �.5�� (90mm) �.9�1 �.5�� 0.��9 0.��� 7.87� �.6�� �.189 1.�85 PP05191�5090
�½" x �" �.9�1 (1�5mm) x �.��1 (110mm) �.9�1 �.��1 0.��9 0.�9� 7.87� �.58� �.5�� 1.68� PP05191�5110
5" x �½" 5.51� (1�0mm) x �.95� (75mm) 5.51� �.95� 0.500 0.�68 9.055 �.6�� �.756 �.��9 PP05191�0075
5" x �" 5.51� (1�0mm) x �.5�� (90mm) 5.51� �.5�� 0.500 0.��� 9.055 �.6�� �.110 �.�6� PP05191�0090
5" x �" 5.51� (1�0mm) x �.��1 (110mm) 5.51� �.��1 0.500 0.�9� 9.055 �.567 �.5�� �.585 PP05191�0110
5" x �" 5.51� (1�0mm) x �.9�1 (1�5mm) 5.51� �.9�1 0.500 0.��9 9.�5� �.6�6 �.661 �.1�� PP05191�01�5
D1 D2
L1L2
L
S2S1
(Continued on Next Page)
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
171.05�609
ChemicalProcess Piping Systems - Dimensional Data
Reducer: Concentric - Extended leg
Description: Reducer: Concentric - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nom. Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in lbs Number
6" x �" 6.�99 (160mm) x �.5�� (90mm) 6.�99 �.5�� 0.575 0.��� 9.76� �.8�� �.�68 �.706 PP0519160090
6" x �" 6.�99 (160mm) x �.��1 (110mm) 6.�99 �.��1 0.575 0.�9� 9.6�6 �.8�� �.701 �.9�6 PP0519160110
6" x �½" 6.�99 (160mm) x �.9�1 (1�5mm) 6.�99 �.9�1 0.575 0.��9 9.6�6 �.80� �.7�0 �.01� PP05191601�5
6" x 5" 6.�99 (160mm) x 5.51� (1�0mm) 6.�99 5.51� 0.575 0.500 10.��6 �.80� �.5�8 �.��� PP05191601�0
7" x �" 7.087 (180mm) x �.5�� (90mm) 7.087 �.5�� 0.6�6 0.��� 9.6�6 �.1�� �.110 �.�66 PP0519180090
7" x �" 7.087 (180mm) x �.��1 (110mm) 7.087 �.��1 0.6�6 0.�9� 10.6�0 �.88� �.701 �.67� PP0519180110
7" x �½" 7.087 (180mm) x �.9�1 (1�5mm) 7.087 �.9�1 0.6�6 0.��9 9.6�6 �.1�� �.��5 �.00� PP05191801�5
7" x 5" 7.087 (180mm) x 5.51� (1�0mm) 7.087 5.51� 0.6�6 0.500 10.6�0 �.9�1 �.�09 �.��� PP05191801�0
7" x 6" 7.087 (180mm) x 6.�99 (160mm) 7.087 6.�99 0.6�6 0.575 10.9�5 �.961 5.000 �.66� PP0519180160
8" x 5" 7.87� (�00mm) x 5.51� (1�0mm) 7.87� 5.51� 0.717 0.500 10.8�7 �.9�1 �.��1 5.016 PP0519�001�0
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� 6.�99 0.717 0.575 10.8�7 �.8�� �.80� 5.��6 PP0519�00160
8" x 7" 7.87� (�00mm) x 7.087 (180mm) 7.87� 7.087 0.717 0.6�6 10.709 �.961 �.6�6 5.85� PP0519�00180
9" x 6" 8.858 (��5mm) x 6.�99 (160mm) 8.858 6.�99 0.807 0.575 11.61� 5.��6 �.80� 6.710 PP0519��5160
9" x 7" 8.858 (��5mm) x 7.087 (180mm) 8.858 7.087 0.807 0.6�6 10.709 �.88� �.5�8 7.19� PP0519�55180
9" x 8" 8.858 (��5mm) x 7.87� (�00mm) 8.858 7.87� 0.807 0.717 10.709 �.961 �.7�� 7.700 PP0519�55�00
10" x 6" 9.8�� (�50mm) x 6.�99 (160mm 9.8�� 6.�99 0.89� 0.575 11.811 5.906 �.9�7 8.151 PP0519�50160
10" x 7" 9.8�� (�50mm) x 7.087 (180mm) 9.8�� 7.087 0.89� 0.6�6 11.61� 6.0�� �.17� 8.910 PP0519�50180
10" x 8" 9.8�� (�50mm) x 7.87� (�00mm) 9.8�� 7.87� 0.89� 0.717 1�.�0� 6.181 �.�88 9.6�6 PP0519�50�00
10" x 9" 9.8�� (�50mm) x 8.858 (��5mm) 9.8�� 8.858 0.89� 0.807 1�.071 6.1�� �.88� 10.670 PP0519�50��5
11" x 8" 11.0�� (�80mm) x 7.87� (�00mm) 11.0�� 7.87� 1.000 0.717 1�.110 5.51� �.�09 1�.870 PP0519�80�00
11" x 9" 11.0�� (�80mm) x 8.858 (��5mm) 11.0�� 8.858 1.000 0.807 1�.189 5.51� �.7�� 1�.�87 PP0519�80��5
11" x 10" 11.0�� (�80mm) x 9.8�� (�50mm) 11.0�� 9.8�� 1.000 0.89� 1�.�86 5.51� 5.118 1�.�88 PP0519�80�50
1�"x 9" 1�.�0� (�15mm) x 8.858 (��5mm) 1�.�0� 8.858 1.1�6 0.807 1�.�70 5.906 �.7�� 17.�80 PP0519�15��5
1�" x 10" 1�.�0� (�15mm) x 9.8�� (�50mm) 1�.�0� 9.8�� 1.1�6 0.89� 1�.�70 5.906 5.�76 17.8�0 PP0519�15�50
1�" x 11" 1�.�0� (�15mm) x 11.0�� (�80mm) 1�.�0� 11.0�� 1.1�6 1.000 1�.�70 5.906 5.�7� 19.�60 PP0519�15�80
D1 D2
L1L2
L
S2S1
18
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
d1d2
L1
L2
L
S2
S1
PN 10 / SDR 11
Nominal Actual OD d1 d2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in lbs Number
¾" x ½" 0.98� (�5mm) x 0.787 (�0mm) 0.98� 0.787 0.091 0.075 �.055 �.008 1.�96 0.0�� PP050�00�50�0
1" x ¾" 1.�60 (��mm) x 0.98� (�5mm) 1.�60 0.98� 0.11� 0.091 �.�88 �.�05 1.575 0.0�� PP050�00��0�5
1¼" x ¾" 1.575 (�0mm) x 0.98� (�5mm) 1.575 0.98� 0.1�6 0.091 �.961 �.�6� 1.575 0.088 PP050�00�00�5
1¼" x 1" 1.575 (�0mm) x 1.�60 (��mm) 1.575 1.�60 0.1�6 0.11� �.9�1 �.��� 1.7�� 0.088 PP050�00�00��
1½" x 1" 1.969 (50mm) x 1.�60 (��mm) 1.969 1.�60 0.181 0.11� 6.1�� �.795 1.77� 0.176 PP050�00500��
1½" x 1¼" 1.969 (50mm) x 1.575 (�0mm) 1.969 1.575 0.181 0.1�6 6.181 �.795 1.9�9 0.176 PP050�00500�0
�" x 1" �.�80 (6�mm) x 1.�60 (��mm) �.�80 1.�60 0.��8 0.11� 6.969 �.95� 1.77� 0.�6� PP050�006�0��
�" x 1¼" �.�80 (6�mm) x 1.575 (�0mm) �.�80 1.575 0.��8 0.1�6 6.969 �.99� 1.9�9 0.�08 PP050�006�0�0
�" x 1½" �.�80 (6�mm) x 1.969 (50mm) �.�80 1.969 0.��8 0.181 6.969 �.99� �.�05 0.��0 PP050�006�050
�½" x 1½" �.95� (75mm) x 1.969 (50mm) �.95� 1.969 0.�68 0.181 7.756 �.�07 �.��� 0.�6� PP050�0075050
�½" x �" �.95� (75mm) x �.�80 (6�mm) �.95� �.�80 0.�68 0.��8 7.756 �.�68 �.�80 0.550 PP050�007506�
�" x �" �.5�� (90mm) x �.�80 (6�mm) �.5�� �.�80 0.��� 0.��8 8.661 �.6�� �.5�0 0.79� PP050�009006�
�" x �½" �.5�� (90mm) x �.95� (75mm) �.5�� �.95� 0.��� 0.�68 8.58� �.661 �.756 0.858 PP050�0090075
�" x �" �.��1 (110mm) x �.�80 (6�mm) �.��1 �.�80 0.�9� 0.��8 9.7�� �.898 �.�80 1.�5� PP050�011006�
�" x �" �.��1 (110mm) x �.5�� (90mm) �.��1 �.5�� 0.�9� 0.��� 9.606 �.858 �.110 1.��0 PP050�0110090
�½" x �" �.9�1 (1�5mm) x �.�80 (6�mm)) �.9�1 �.�80 0.��9 0.��8 10.��� �.976 �.�80 1.760 PP050�01�506�
�½" x �" �.9�1 (1�5mm) x �.5�� (90mm) �.9�1 �.5�� 0.��9 0.��� 10.�7� �.�1� �.110 1.980 PP050�01�5090
�½" x �" �.9�1 (1�5mm) x �.��1 (110mm) �.9�1 �.��1 0.��9 0.�9� 10.��� �.17� �.��5 �.090 PP050�01�5110
5" x �" 5.51� (1�0mm) x �.9�1 (1�5mm) 5.51� �.9�1 0.500 0.��9 11.1�� �.��1 �.7�0 �.860 PP050�01�01�5
6" x �" 6.�99 (160mm) x �.5�� (90mm) 6.�99 �.5�� 0.575 0.��� 1�.165 �.6�6 �.110 �.��� PP050�0160090
6" x �" 6.�99 (160mm) x �.��1 (110mm) 6.�99 �.��1 0.575 0.�9� 1�.165 �.567 �.��5 �.5�� PP050�0160110
6" x �½" 6.�99 (160mm) x �.9�1 (1�5mm) 6.�99 �.9�1 0.575 0.��9 1�.165 �.606 �.6�� �.850 PP050�01601�5
6" x 5" 6.�99 (160mm) x 5.51� (1�0mm) 6.�99 5.51� 0.575 0.500 1�.1�6 �.606 �.898 �.1�6 PP050�01601�0
7" x �" 7.087 (180mm) x �.5�� (90mm) 7.087 �.5�� 0.6�6 0.��� 1�.701 5.079 �.110 �.86� PP050�0180090
7" x �½" 7.087 (180mm) x �.9�1 (1�5mm) 7.087 �.9�1 0.6�6 0.��9 1�.898 5.�5� �.701 5.��6 PP050�01801�5
7" x 6" 7.087 (180mm) x 6.�99 (160mm) 7.087 6.�99 0.6�6 0.575 1�.898 5.�5� �.1�� 5.896 PP050�0180160
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� 6.�99 0.717 0.575 1�.685 5.�7� �.1�� 7.�9� PP050�0��0160
8" x 7" 7.87� (�00mm) x 7.087 (180mm) 7.87� 7.087 0.717 0.6�6 1�.685 5.669 �.�09 8.1�0 PP050�0�00180
9" x 6" 8.858 (��5mm) x 6.�99 (160mm) 8.858 6.�99 0.807 0.575 15.9�5 6.10� �.055 9.61� PP050�0��5160
9" x 7" 8.858 (��5mm) x 7.087 (180mm) 8.858 7.087 0.807 0.6�6 15.866 6.10� �.�70 9.900 PP050�0��5180
9" x 8" 8.858 (��5mm) x 7.87� (�00mm) 8.858 7.87� 0.807 0.717 15.866 6.1�� �.6�6 10.8�6 PP050�0��5�00
10" x 8" 9.8�� (�50mm) x 8.858 (��5mm) 9.8�� 8.858 0.89� 0.807 17.��� 6.850 5.000 1�.�76 PP050�0�50��5
Reducer: Eccentric - Extended leg
Description: Reducer: Eccentric - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
191.05�609
ChemicalProcess Piping Systems - Dimensional Data
Description: Stub Ends PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
Stub Ends
PN 10 / SDR 11
Nominal Actual OD D S D3 D4 H1 h4 z1 Weight Part
Size Size in in in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 1.0�� 1.7�� 0.�76 0.787 1.969 0.0�0 PP05060�0
¾" 0.98� (�5mm) 0.98� 0.091 1.�60 �.1�6 0.�5� 0.787 1.969 0.068 PP05060�5
1" 1.�60 (��mm) 1.�60 0.11� 1.5�5 �.�80 0.�9� 0.787 1.969 0.099 PP05060��
1¼" 1.575 (�0mm) 1.575 0.1�6 1.890 �.87� 0.��� 0.787 1.969 0.156 PP05060�0
1½" 1.969 (50mm) 1.969 0.181 �.�6� �.��8 0.�7� 0.787 1.969 0.198 PP0506050
�" �.�80 (6�mm) �.�80 0.��8 �.87� �.9�7 0.591 0.906 �.�05 0.�97 PP050606�
�½" �.95� (75mm) �.95� 0.�68 �.��5 �.7�� 0.6�0 0.8�7 �.165 0.�66 PP0506075
�" �.5�� (90mm) �.5�� 0.��� �.055 5.��6 0.709 1.890 �.�68 0.700 PP0506090
�" �.��1 (110mm) �.��1 0.�9� �.961 6.�60 0.7�8 1.65� �.�07 1.01� PP0506110
�½" �.9�1 (1�5mm) �.9�1 0.��9 5.��6 6.�60 1.0�� 1.�96 �.50� 1.107 PP05061�5
5" 5.51� (1�0mm) 5.51� 0.500 6.10� 7.�0� 0.98� 1.�99 �.�68 1.595 PP05061�0
6" 6.�99 (160mm) 6.�99 0.575 6.9�9 8.�86 0.98� 1.�99 �.189 �.0�� PP0506160
7" 7.087 (180mm) 7.087 0.6�6 7.1�6 8.�86 1.181 �.0�7 �.�68 �.057 PP0506180
8" 7.87� (�00mm) 7.87� 0.717 9.17� 10.551 1.�99 �.165 �.8�� �.675 PP0506�00
9" 8.858 (��5mm) 8.858 0.807 9.�5� 10.591 1.�99 �.�05 �.76� �.65� PP0506��5
10" 9.8�� (�50mm) 9.8�� 0.89� 11.��0 1�.598 1.�78 �.008 �.76� 6.710 PP0506�50
11" 11.0�� (�80mm) 11.0�� 1.000 11.�96 1�.6�8 1.�78 �.717 �.685 6.5�� PP0506�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 1�.��8 1�.685 1.�17 �.�86 6.7�� 9.�9� PP0506�15
1�" 1�.976 (�55mm) 1�.976 1.�68 1�.7�� 16.969 1.61� �.701 7.�8� 1�.�08 PP0506�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 16.811 19.016 1.811 �.1�� 7.717 18.�60 PP0506�00
18" 17.717 (�50mm) 17.717 1.610 �0.��6 ��.110 �.�6� �.5�0 5.551 �0.�60 PP0506�50
�0" 19.685 (500mm) 19.685 1.787 �0.866 ��.110 �.�0� �.��1 5.��� �0.0�1 PP0506500
��" ��.0�7 (560mm) ��.0�7 �.000 ��.�1� �6.969 �.�6� �.�6� 5.51� �5.��0 PP0506560
D3 D D4
h4H1
z1
S
�0
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Stub End - Extended leg
Description: Stub End - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S D3 D4 H1 h4 z1 Weight Part
Size Size in in in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 1.06� 1.7�� 0.�76 1.�57 �.��6 0.0�� PP05�800�0
¾" 0.98� (�5mm) 0.98� 0.091 1.�99 �.1�6 0.�5� 1.575 �.��6 0.088 PP05�800�5
1" 1.�60 (��mm) 1.�60 0.11� 1.575 �.�80 0.�9� 1.7�� �.��6 0.1�0 PP05�800��
1¼" 1.575 (�0mm) 1.575 0.1�6 1.969 �.87� 0.��� 1.9�9 �.��6 0.187 PP05�800�0
1½" 1.969 (50mm) 1.969 0.181 �.�0� �.�68 0.�7� �.165 �.09� 0.�99 PP05�80050
�" �.�80 (6�mm) �.�80 0.��8 �.95� �.976 0.551 �.�80 �.7�� 0.�66 PP05�8006�
�½" �.95� (75mm) �.95� 0.�68 �.50� �.�70 0.6�0 �.756 5.118 0.70� PP05�80075
�" �.5�� (90mm) �.5�� 0.��� �.1�� �.7�� 0.669 �.110 5.51� 1.056 PP05�80090
�" �.��1 (110mm) �.��1 0.�9� �.961 6.�99 0.7�8 �.��9 6.�96 1.��0 PP05�80110
�½" �.9�1 (1�5mm) �.9�1 0.��9 5.197 6.��0 0.98� 5.�5� 7.�0� �.156 PP05�801�5
5" 5.51� (1�0mm) 5.51� 0.500 6.10� 7.�0� 0.98� 5.079 7.87� �.68� PP05�801�0
6" 6.�99 (160mm) 6.�99 0.575 6.9�9 8.�86 1.0�� 5.�76 7.�6� �.5�0 PP05�80160
7" 7.087 (180mm) 7.087 0.6�6 7.087 8.��6 1.181 5.��6 7.87� �.916 PP05�80180
8" 7.87� (�00mm) 7.87� 0.717 9.17� 10.591 1.�99 5.000 7.91� 6.6�� PP05�80�00
9" 8.858 (��5mm) 8.858 0.807 9.��1 10.6�0 1.�99 5.118 8.0�1 7.0�0 PP05�80��5
10" 9.8�� (�50mm) 9.8�� 0.89� 11.��0 1�.598 1.�78 5.51� 8.661 10.560 PP05�80�50
11" 11.0�� (�80mm) 11.0�� 1.000 11.5�5 1�.677 1.�17 5.709 9.09� 11.�85 PP05�80�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 1�.189 1�.606 1.�17 6.10� 9.606 15.88� PP05�80�15
D3 D D4
h4
H1
z1
S
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�11.05�609
ChemicalProcess Piping Systems - Dimensional Data
Backing Ring
Description: Backing Ring 150 lbs. ANSI Drilling
Material: Glass Filled Polypropylene with Steel Core
Execution: Molded
Nominal B D D2 d6 K # Weight SIMTECH
Size in in in in in Holes lbs Part #
½" 0.�7� �.50� 0.6�0 1.��0 �.�6� � 0.�8� PP990700�0
¾" 0.�7� �.858 0.6�0 1.�19 �.756 � 0.660 PP990700�5
1" 0.6�0 �.�5� 0.6�0 1.6�� �.110 � 0.970 PP990700��
1¼" 0.6�0 �.606 0.6�0 1.988 �.50� � 1.188 PP990700�0
1½" 0.709 5.000 0.6�0 �.��1 �.858 � 1.�5� PP99070050
�" 0.709 5.98� 0.7�8 �.051 �.76� � 1.78� PP9907006�
�½" 0.709 7.008 0.7�8 �.�8� 5.51� � �.�18 PP99070075
�" 0.709 7.�80 0.7�8 �.�5� 5.98� 8 �.��0 PP99070090
�" & �½" 0.709 9.016 0.7�8 5.0�9 7.5�0 8 �.0�8 PP99070110
6" & 7" 0.9�5 11.0�� 0.87� 7.1�6 9.�88 8 6.��5 PP99070160
8" & 9" 0.9�5 1�.50� 0.87� 9.�70 11.7�� 8 10.�56 PP99070�00
10" & 11" 1.181 15.98� 1.000 11.516 1�.�5� 1� 1�.6�8 PP99070�50
1�" 1.��9 19.016 1.000 1�.�87 17.008 1� �6.��� PP99070�15
1�" 1.65� �0.98� 1.1�� 1�.78� 18.7�0 16 ��.5�0 PP99070�55
16" 1.7�� ��.50� 1.1�� 16.890 �1.�60 16 �8.7�0 PP99070�00
D2
D
B
d6
K
��
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Caps: Dome
Description: End Caps PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S L Weight Part
Size Size in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 1.811 0.01� PP05�100�0
¾" 0.98� (�5mm) 0.98� 0.091 1.969 0.0�� PP05�100�5
1" 1.�60 (��mm) 1.�60 0.11� �.165 0.0�7 PP05�100��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.�0� 0.06� PP05�100�0
1½" 1.969 (50mm) 1.969 0.181 �.756 0.11� PP05�10050
�" �.�80 (6�mm) �.�80 0.��8 �.��8 0.�07 PP05�1006�
�½" �.95� (75mm) �.95� 0.�68 �.6�� 0.��� PP05�10075
�" �.5�� (90mm) �.5�� 0.��� �.1�� 0.506 PP05�10090
�" �.��1 (110mm) �.��1 0.�9� �.7�� 0.880 PP05�10110
�½" �.9�1 (1�5mm) �.9�1 0.��9 �.961 1.195 PP05�101�5
5" 5.51� (1�0mm) 5.51� 0.500 5.�5� 1.6�1 PP05�101�0
6" 6.�99 (160mm) 6.�99 0.575 5.906 �.�98 PP05�10160
7" 7.087 (180mm) 7.087 0.6�6 6.�99 �.168 PP05�10180
8" 7.87� (�00mm) 7.87� 0.717 6.890 �.158 PP05�10�00
9" 8.858 (��5mm) 8.858 0.807 7.87� 5.676 PP05�10��5
10" 9.8�� (�50mm) 9.8�� 0.89� 8.071 5.9�0 PP05�10�50
11" 11.0�� (�80mm) 11.0�� 1.000 9.�5� 6.8�0 PP05�10�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 10.0�9 1�.5�0 PP05�10�15
1�" 1�.976 (�55mm) 1�.976 1.�68 11.0�� �0.0�0 PP05�10�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 1�.�05 �6.8�0 PP05�10�00
D
S
L
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
��1.05�609
ChemicalProcess Piping Systems - Dimensional Data
Caps: Flat
Description: End Caps PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Machined
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S L L1 Weight Part
Size Size in in in in lbs Number
10" 9.8�� (�50mm) 9.8�� 0.89� 1.969 1.�57 �.0�8 PP05090�50
11" 11.0�� (�80mm) 11.0�� 1.000 �.165 1.6�� 5.6�� PP05090�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 �.�6� 1.8�1 7.9�0 PP05090�15
1�" 1�.976 (�55mm) 1�.976 1.�68 �.559 �.067 11.088 PP05090�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 �.756 �.��� 15.6�� PP05090�00
18" 17.717 (�50mm) 17.717 1.610 �.150 �.618 ��.��0 PP05090�50
�0" 19.685 (500mm) 19.685 1.787 �.��6 �.9�� �0.800 PP05090500
D
S
LL1
��
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
lateral: 45°
Description: Lateral: 45° PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Fabricated
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S L2 z2 z3 Weight Part
Size Size in in in in in lbs Number
�" �.��1 (110mm) �.��1 0.�9� �0.079 16.9�9 �.150 16.9�9 PP05170110
�½" �.9�1 (1�5mm) �.9�1 0.��9 �1.65� 17.717 �.9�7 17.717 PP051701�5
5" 5.51� (1�0mm) 5.51� 0.500 ��.��8 18.50� �.7�� 18.50� PP051701�0
6" 6.�99 (160mm) 6.�99 0.575 �8.7�0 19.685 9.055 19.685 PP05170160
7" 7.087 (180mm) 7.087 0.6�6 �0.709 �0.866 9.8�� �0.866 PP05170180
8" 7.87� (�00mm) 7.87� 0.717 ��.677 �1.65� 11.0�� �1.65� PP05170�00
9" 8.858 (��5mm) 8.858 0.807 ��.6�6 ��.8�5 11.811 ��.8�5 PP05170��5
10" 9.8�� (�50mm) 9.8�� 0.89� �7.008 ��.016 1�.99� ��.016 PP05170�50
11" 11.0�� (�80mm) 11.0�� 1.000 �9.�70 �5.591 1�.780 �5.591 PP05170�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 ��.�07 �7.559 15.7�8 �7.559 PP05170�15
1�" 1�.976 (�55mm) 1�.976 1.�68 50.�9� ��.�65 16.9�9 ��.�65 PP05170�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 5�.150 �5.��� 17.717 �5.��� PP05170�00
18" 17.717 (�50mm) 17.717 1.610 56.�99 �7.�0� 18.898 �7.�0� PP05170�50
�0" 19.685 (500mm) 19.685 1.787 59.055 �9.�70 19.685 �9.�70 PP05170500
D
D
S
L2
z2
z3 z2
45°
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�51.05�609
ChemicalProcess Piping Systems - Dimensional Data
PN 10 / SDR 11
Nominal Actual OD d s L2 z2 z3 Weight Part
Size Size in in in in in lbs Number
�" �.��1 (110mm) �.��1 0.�9� 19.685 1�.795 6.890 5.1�8 PP05165110
�½" �.9�1 (1�5mm) �.9�1 0.��9 �1.�57 1�.976 7.�80 7.��8 PP051651�5
5" 5.51� (1�0mm) 5.51� 0.500 ��.87� 1�.055 8.819 9.5�8 PP051651�0
6" 6.�99 (160mm) 6.�99 0.575 �5.�76 16.��0 9.055 1�.6�0 PP05165160
7" 7.087 (180mm) 7.087 0.6�6 �7.559 17.717 9.8�� 18.656 PP05165180
8" 7.87� (�00mm) 7.87� 0.717 �9.88� 19.17� 10.709 ��.6�0 PP05165�00
9" 8.858 (��5mm) 8.858 0.807 ��.677 �0.866 11.811 ��.100 PP05165��5
10" 9.8�� (�50mm) 9.8�� 0.89� �5.6�0 ��.8�5 1�.795 �5.760 PP05165�50
11" 11.0�� (�80mm) 11.0�� 1.000 �9.17� ��.80� 1�.�70 6�.�60 PP05165�80
1�" 1�.�0� (�15mm) 1�.�0� 1.1�6 ��.91� �7.165 15.7�8 85.�60 PP05165�15
1�" 1�.976 (�55mm) 1�.976 1.�68 �5.�7� �8.7�0 16.7�� 11�.�00 PP05165�55
16" 15.7�8 (�00mm) 15.7�8 1.��9 �9.�1� �1.�96 17.717 155.760 PP05165�00
18" 17.717 (�50mm) 17.717 1.610 5�.165 ��.�65 18.701 �07.0�0 PP05165�50
�0" 19.685 (500mm) 19.685 1.787 55.118 �5.��� 19.685 �1�.�1� PP05165500
lateral: 60°
Description: Lateral: 60° PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Fabricated
Connection: Butt Fusion
D
D
S
L2
z2
z3 z2
45°
�6
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Male adapter - Extended leg
Description: Threaded Male Adapter - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S A D2 L Le sw Weight Part
Size Size in in in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 0.551 0.51� �.�8� 1.61� 0.9�5 0.0�0 PP051�00�0
¾" 0.98� (�5mm) 0.98� 0.091 0.551 0.709 �.�0� 1.61� 1.06� 0.0�9 PP051�00�5
1" 1.�60 (��mm) 1.�60 0.11� 0.709 0.906 �.717 1.7�� 1.�17 0.0�8 PP051�00��
1¼" 1.575 (�0mm) 1.575 0.1�6 0.7�8 1.1�� �.95� 1.9�9 1.811 0.08� PP051�00�0
1½" 1.969 (50mm) 1.969 0.181 0.787 1.��9 �.��8 �.165 �.165 0.1�8 PP051�0050
�" �.�80 (6�mm) �.�80 0.��8 0.8�7 1.77� �.58� �.�80 �.165 0.�11 PP051�006�
D
Le
S
D2sw
AL
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�71.05�609
ChemicalProcess Piping Systems - Dimensional Data
Female adapter - Extended leg
Description: Threaded Female Adapter - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD D S A sw L Le Weight Part
Size Size in in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 0.6�0 1.181 �.�8� 1.61� 0.0�5 PP051�00�0
¾" 0.98� (�5mm) 0.98� 0.091 0.709 1.�17 �.�80 1.61� 0.0�8 PP051�00�5
1" 1.�60 (��mm) 1.�60 0.11� 0.8�7 1.811 �.795 1.7�� 0.088 PP051�00��
1¼" 1.575 (�0mm) 1.575 0.1�6 0.906 �.165 �.110 1.9�9 0.1�8 PP051�00�0
1½" 1.969 (50mm) 1.969 0.181 0.9�5 �.��1 �.�07 �.165 0.17� PP051�0050
�" �.�80 (6�mm) �.�80 0.��8 1.1�� �.95� �.819 �.�80 0.��8 PP051�006�
D
Le
S
sw
A
L
�8
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Union - EPDM - Extended leg
Description: Union with EPDM O-Ring - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD d S D L Le1 Le2 Weight Part
Size Size in in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 1.811 �.1�� 0.9�5 1.�57 0.1�1 PP05�600�0
¾" 0.98� (�5mm) 0.98� 0.091 �.�05 �.��1 0.9�5 1.�96 0.187 PP05�600�5
1" 1.�60 (��mm) 1.�60 0.11� �.�80 �.6�6 0.9�5 1.5�5 0.�51 PP05�600��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.0�1 �.8�� 0.9�5 1.61� 0.��9 PP05�600�0
1½" 1.969 (50mm) 1.969 0.181 �.�65 5.079 0.9�5 1.7�� 0.601 PP05�60050
�" �.�80 (6�mm) �.�80 0.��8 �.�1� 5.�15 0.9�5 1.7�� 0.990 PP05�6006�
LLe2 Le1
dDs
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�91.05�609
ChemicalProcess Piping Systems - Dimensional Data
Union - VITon - Extended leg
Description: Union with Viton O-Ring - Extended Leg PN10 / SDR 11 - 150psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 10 / SDR 11
Nominal Actual OD d S D L Le1 Le2 Weight Part
Size Size in in in in in in lbs Number
½" 0.787 (�0mm) 0.787 0.075 1.811 �.1�� 0.9�5 1.�57 0.1�1 PP05�600�0
¾" 0.98� (�5mm) 0.98� 0.091 �.�05 �.��1 0.9�5 1.�96 0.187 PP05�600�5
1" 1.�60 (��mm) 1.�60 0.11� �.�80 �.6�6 0.9�5 1.5�5 0.�51 PP05�600��
1¼" 1.575 (�0mm) 1.575 0.1�6 �.0�1 �.8�� 0.9�5 1.61� 0.��9 PP05�600�0
1½" 1.969 (50mm) 1.969 0.181 �.�65 5.079 0.9�5 1.7�� 0.601 PP05�60050
�" �.�80 (6�mm) �.�80 0.��8 �.�1� 5.�15 0.9�5 1.7�� 0.990 PP05�6006�
LLe2 Le1
dDs
�0
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
90psi Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�11.05�609
ChemicalProcess Piping Systems - Dimensional Data
PRESSURE PIPE
Description: Pressure Pipe PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Extruded, Stress Relieved
Connection: Butt Fusion
PN 6 / SRD 17.6
Nomnial Actual OD D S Weight Weight Part
Size Size in in (lbs./ m) Lbs. Foot Number
¾" 0.98� (�5mm) 0.98� 0.071 0.�90 0.091 PP0�0000�5
1" 1.�60 (��mm) 1.�60 0.071 0.�78 0.118 PP0�0000��
1¼" 1.575 (�0mm) 1.575 0.091 0.601 0.188 PP0�0000�0
1½" 1.969 (50mm) 1.969 0.11� 0.9�8 0.�90 PP0�000050
�" �.�80 (6�mm) �.�80 0.1�� 1.�50 0.�5� PP0�00006�
�½" �.95� (75mm) �.95� 0.169 �.057 0.6�� PP0�000075
�" �.5�� (90mm) �.5�� 0.�01 �.9�6 0.91� PP0�000090
�" �.��1 (110mm) �.��1 0.��8 �.�78 1.�68 PP0�000110
�½" �.9�1 (1�5mm) �.9�1 0.�80 5.610 1.75� PP0�0001�5
5" 5.51� (1�0mm) 5.51� 0.�15 7.0�0 �.�00 PP0�0001�0
6" 6.�99 (160mm) 6.�99 0.�58 9.17� �.867 PP0�000160
7" 7.087 (180mm) 7.087 0.�0� 11.550 �.609 PP0�000180
8" 7.87� (�00mm) 7.87� 0.��9 1�.�00 �.�69 PP0�000�00
9" 8.858 (��5mm) 8.858 0.50� 18.018 5.6�1 PP0�000��5
10" 9.8�� (�50mm) 9.8�� 0.559 ��.��0 6.9�� PP0�000�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 �7.7�0 8.66� PP0�000�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 �5.�00 11.000 PP0�000�15
1�" 1�.976 (�55mm) 1�.976 0.791 ��.660 1�.956 PP0�000�55
16" 15.7�8 (�00mm) 15.7�8 0.89� 56.5�0 17.669 PP0�000�00
18" 17.717 (�50mm) 17.717 1.00� 71.500 ��.��� PP0�000�50
�0" 19.685 (500mm) 19.685 1.118 88.��0 �7.6�8 PP0�000500
��" ��.0�7 (560mm) ��.0�7 1.��8 110.660 ��.581 PP0�000560
��" ��.80� (6�0mm) ��.80� 1.�06 1�0.1�0 ��.79� PP0�0006�0
�8" �7.95� (710mm) �7.95� 1.58� 177.760 55.550 PP0�000710
�0" �1.�96 (800mm) �1.�96 1.78� ��5.7�0 70.5�7 PP0�000800
D
S
��
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Description: Elbow: 90° PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
Elbow: 90°
PN6 / SDR 17.6
Nomnial Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
1½" 1.969 (50mm) 1.969 0.11� 0.�76 �.087 0.095 PP0�010050
�" �.�80 (6�mm) �.�80 0.1�� 0.�76 �.598 0.180 PP0�01006�
�½" �.95� (75mm) �.95� 0.169 0.��� �.150 0.�08 PP0�010075
�" �.5�� (90mm) �.5�� 0.�01 0.��� �.7�0 0.�55 PP0�010090
�" �.��1 (110mm) �.��1 0.��8 0.�7� �.5�8 0.8�5 PP0�010110
�½" �.9�1 (1�5mm) �.9�1 0.�80 0.669 5.118 1.��1 PP0�0101�5
5" 5.51� (1�0mm) 5.51� 0.�15 0.591 5.709 1.650 PP0�0101�0
6" 6.�99 (160mm) 6.�99 0.�58 0.�15 6.�96 �.57� PP0�010160
7" 7.087 (180mm) 7.087 0.�0� 0.591 7.��� �.5�0 PP0�010180
8" 7.87� (�00mm) 7.87� 0.��9 0.7�8 8.110 5.10� PP0�010�00
9" 8.858 (��5mm) 8.858 0.50� 0.�9� 9.09� 7.0�0 PP0�010��5
10" 9.8�� (�50mm) 9.8�� 0.559 0.787 10.079 9.�7� PP0�010�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 0.9�5 11.�17 1�.89� PP0�010�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 0.866 1�.756 18.568 PP0�010�15
1�" 1�.976 (�55mm) 1�.976 0.791 1.�96 15.157 �9.�60 PP0�010�55
16" 15.7�8 (�00mm) 15.7�8 0.89� 1.61� 17.��� �1.019 PP0�010�00
Z
D
Le
S
r=d
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
��1.05�609
ChemicalProcess Piping Systems - Dimensional Data
Elbow 90° - Extended leg
Description: Elbow 90° - Extended Leg PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
1½" 1.969 (50mm) 1.969 0.11� �.150 �.�09 0.�6� PP0�150050
�" �.�80 (6�mm) �.�80 0.1�� �.150 �.567 0.�18 PP0�15006�
�½" �.95� (75mm) �.95� 0.169 �.�65 5.157 0.6�8 PP0�150075
�" �.5�� (90mm) �.5�� 0.��0 �.�65 5.6�0 0.968 PP0�150090
�" �.��1 (110mm) �.��1 0.��8 �.858 6.�99 1.68� PP0�150110
�½" �.9�1 (1�5mm) �.9�1 0.�80 �.9�7 6.890 1.91� PP0�1501�5
5" 5.51� (1�0mm) 5.51� 0.�15 �.7�� 7.87� �.68� PP0�1501�0
6" 6.�99 (160mm) 6.�99 0.�58 5.��� 5.�15 �.9�8 PP0�150160
7" 7.087 (180mm) 7.087 0.�0� 5.��� 5.709 6.�79 PP0�150180
8" 7.87� (�00mm) 7.87� 0.��9 5.906 6.�96 8.888 PP0�150�00
9" 8.858 (��5mm) 8.858 0.50� 5.906 11.0�� 11.869 PP0�150��5
10" 9.8�� (�50mm) 9.8�� 0.559 5.118 11.61� 1�.618 PP0�150�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 5.51� 1�.795 19.008 PP0�150�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 5.906 1�.76� �5.��� PP0�150�15
Z
D
Le
S
��
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Elbow 45° - Extended leg
Description: Elbow 45° - Extended Leg PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
1½" 1.969 (50mm) 1.969 0.11� �.��1 �.�5� 0.�09 PP0�160050
�" �.�80 (6�mm) �.�80 0.1�� �.598 �.5�8 0.�59 PP0�16006�
�½" �.95� (75mm) �.95� 0.169 �.795 5.118 0.��1 PP0�160075
�" �.5�� (90mm) �.5�� 0.�01 �.��8 5.51� 0.7�7 PP0�160090
�" �.��1 (110mm) �.��1 0.��8 �.661 6.�99 1.�10 PP0�160110
�½" �.9�1 (1�5mm) �.9�1 0.�80 �.7�0 6.69� 1.7�8 PP0�1601�5
5" 5.51� (1�0mm) 5.51� 0.�15 �.7�� 7.95� �.1�� PP0�1601�0
6" 6.�99 (160mm) 6.�99 0.�58 5.6�0 9.055 �.817 PP0�160160
7" 7.087 (180mm) 7.087 0.�0� �.8�� 9.��9 5.159 PP0�160180
8" 7.87� (�00mm) 7.87� 0.��9 5.98� 10.��6 6.86� PP0�160�00
9" 8.858 (��5mm) 8.858 0.50� 6.0�� 10.8�7 8.580 PP0�160��5
10" 9.8�� (�50mm) 9.8�� 0.559 5.��6 11.�96 10.9�� PP0�160�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 5.591 1�.598 15.686 PP0�160�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 6.06� 1�.567 �1.1�0 PP0�160�15
Z
D
Le
ZLeS
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�51.05�609
ChemicalProcess Piping Systems - Dimensional Data
Tee
Description: Tee PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN6 / SDR 17.6
Nominal Actual OD D S L L1 Z Weight Part
Size Size in in in in in lbs Number
1½" 1.969 (50mm) 1.969 0.11� �.9�7 0.�7� 1.969 0.198 PP0�0�0050
�" �.�80 (6�mm) �.�80 0.1�� 5.0�9 0.6�0 �.677 0.�87 PP0�0�006�
�½" �.95� (75mm) �.95� 0.169 5.906 0.7�8 �.99� 0.66� PP0�0�0075
�" �.5�� (90mm) �.5�� 0.�01 7.�05 1.5�5 �.9�7 0.968 PP0�0�0090
�" �.��1 (110mm) �.��1 0.��8 10.0�9 �.165 5.157 �.156 PP0�0�0110
�½" �.9�1 (1�5mm) �.9�1 0.�80 9.8�� 1.969 5.118 �.56� PP0�0�01�5
5" 5.51� (1�0mm) 5.51� 0.�15 1�.�6� �.�6� 6.�99 �.0�8 PP0�0�01�0
6" 6.�99 (160mm) 6.�99 0.�58 1�.5�0 �.165 6.�17 5.�58 PP0�0�0160
7" 7.087 (180mm) 7.087 0.�0� 16.9�9 �.6�� 8.5�� 9.0�� PP0�0�0180
8" 7.87� (�00mm) 7.87� 0.��9 17.1�6 �.�65 8.�65 11.176 PP0�0�0�00
9" 8.858 (��5mm) 8.858 0.50� 17.717 �.8�5 8.9�7 15.00� PP0�0�0��5
10" 9.8�� (�50mm) 9.8�� 0.559 17.6�8 �.5�0 8.819 16.500 PP0�0�0�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 �0.669 �.��8 10.�15 ��.�00 PP0�0�0�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 ��.�8� �.��8 11.1�� �0.800 PP0�0�0�15
1�" 1�.976 (�55mm) 1�.976 0.791 �7.��� �.9�7 1�.58� �6.�00 PP0�0�0�55
16" 15.7�8 (�00mm) 15.7�8 0.89� �8.5�� �.016 1�.��9 57.�00 PP0�0�0�00
ZD
L1
L
S
�6
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Tee: Reduced
Description: Tee: Reduced PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D1 d2 S1 S2 L L1 L2 z1 z2 Weight Part
Size Size in in in in in in in in in lbs Number
�" x 1" �.5�� (90mm) x 1.�60 (��mm) �.5�� 1.�60 0.�01 0.071 7.99� �.087 0.906 �.016 �.��6 0.68� PP0�0�0900��
�" x 1" �.��1 (110mm) x 1.�60 (��mm) �.��1 1.�60 0.��8 0.071 9.�1� �.598 0.866 �.606 �.58� 1.��� PP0�0�1100��
�" x 1½" �.��1 (110mm) x 1.969 (50mm) �.��1 1.969 0.��8 0.11� 9.��9 �.598 1.06� �.606 �.976 1.�7� PP0�0�110050
�½" x �" �.9�1 (1�5mm) x �.�80 (6�mm) �.9�1 �.�80 0.�80 0.1�� 10.0�9 �.1�6 0.98� 5.000 �.�1� �.��� PP0�0�1�506�
�½" x �" �.9�1 (1�5mm) x �.5�� (90mm) �.9�1 �.5�� 0.�80 0.�01 10.�9� 1.77� 1.65� 5.197 �.8�� �.66� PP0�0�1�5090
5" x �" 5.51� (1�0mm) x �.�80 (6�mm) 5.51� �.�80 0.�15 0.1�� 11.�57 �.�68 1.�60 5.7�8 �.7�� �.8�8 PP0�0�1�006�
5" x �" 5.51� (1�0mm) x �.5�� (90mm) 5.51� �.5�� 0.�15 0.�01 11.�57 �.189 1.�78 5.7�8 �.7�� �.9�8 PP0�0�1�0090
5" x �½" 5.51� (1�0mm) x �.95� (75mm) 5.51� �.95� 0.�15 0.169 11.�57 �.189 1.61� 5.7�8 5.118 �.�76 PP0�0�1�0075
5" x �" 5.51� (1�0mm) x �.��1 (110mm) 5.51� �.��1 0.�15 0.��8 11.�57 1.969 1.7�� 5.7�8 5.51� �.960 PP0�0�1�0110
5" x �½" 5.51� (1�0mm) x �.9�1 (1�5mm) 6.�99 �.9�1 0.�58 0.�80 1�.�0� �.�8� 1.850 6.��0 5.906 �.8�8 PP0�0�1601�5
6" x �" 6.�99 (160mm) x �.�80 (6�mm) 7.087 �.��1 0.�0� 0.��8 1�.701 �.9�1 1.181 6.850 5.51� 5.1�8 PP0�0�18006�
6" x �½" 6.�99 (160mm) x �.95� (75mm) 7.087 �.�80 0.�0� 0.1�� 1�.701 �.�09 1.181 6.850 6.�99 �.6�� PP0�0�180075
7" x �" 7.087 (180mm) x �.��1 (110mm) 7.087 �.95� 0.�0� 0.169 1�.701 �.6�� 1.969 6.850 5.906 �.�00 PP0�0�180110
8" x �" 7.87� (�00mm) x �.�80 (6�mm) 7.87� 6.�99 0.��9 0.�58 15.0�9 5.6�0 1.��0 7.5�0 5.709 7.788 PP0�0��0006�
8" x �" 7.87� (�00mm) x �.5�� (90mm) 7.87� �.�80 0.��9 0.1�� 15.�5� �.961 1.575 7.5�0 6.�78 6.8�0 PP0�0��00090
8" x �" 7.87� (�00mm) x �.��1 (110mm) 7.87� �.5�� 0.��9 0.�01 15.�5� �.80� 1.575 7.5�0 6.�99 6.996 PP0�0��00110
8" x �½" 7.87� (�00mm) x �.9�1 (1�5mm) 7.87� �.��1 0.��9 0.��8 15.�5� �.�88 1.69� 7.5�0 �.9�1 7.1�8 PP0�0��001�5
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� �.9�1 0.��9 0.�80 15.�5� �.858 �.�6� 7.87� 7.087 7.6�� PP0�0��00160
10" x �" 9.8�� (�50mm) x �.��1 (110mm) 9.8�� �.��1 0.559 0.��8 17.��1 5.�15 1.�99 8.858 7.677 11.000 PP0�0��50110
10" x 6" 9.8�� (�50mm) x 6.�99 (160mm 9.8�� 6.�99 0.559 0.�58 17.��� �.��1 �.�8� 8.858 8.�86 11.000 PP0�0��50160
z2
z1
D1
d2
L1
L2
L
S2
S1
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�71.05�609
ChemicalProcess Piping Systems - Dimensional Data
PN 6 / SDR 17.6
Nominal Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in Lbs Number
�" x 1½" �.�80 (6�mm) x 1.969 (50mm) �.�80 1.969 0.1�� 0.11� �.�6� 1.1�� 1.06� 0.09� PP0�0�06�050
�½" x 1½" �.95� (75mm) x 1.969 (50mm) �.95� 1.969 0.169 0.11� �.756 1.181 1.10� 0.11� PP0�0�075050
�½" x �" �.95� (75mm) x �.�80 (6�mm) �.95� �.�80 0.169 0.1�� �.��8 1.0�� 1.10� 0.095 PP0�0�07506�
�" x 1½" �.5�� (90mm) x 1.969 (50mm) �.5�� 1.969 0.�01 0.11� �.95� 1.181 1.10� 0.180 PP0�0�090050
�" x �" �.5�� (90mm) x �.�80 (6�mm) �.5�� �.�80 0.�01 0.1�� �.95� 1.1�� 1.0�� 0.19� PP0�0�09006�
�" x �½" �.5�� (90mm) x �.95� (75mm) �.5�� �.95� 0.�01 0.169 �.95� 1.��0 1.0�� 0.�05 PP0�0�090075
�" x 1½" �.��1 (110mm) x 1.969 (50mm) �.��1 1.969 0.��8 0.11� �.5�� 0.866 0.7�8 0.�01 PP0�0�110050
�" x �" �.��1 (110mm) x �.�80 (6�mm) �.��1 �.�80 0.��8 0.1�� �.1�� 1.575 1.�17 0.�1� PP0�0�11006�
�" x �½" �.��1 (110mm) x �.95� (75mm) �.��1 �.95� 0.��8 0.169 �.5�� 1.10� 0.7�8 0.�19 PP0�0�110075
�" x �" �.��1 (110mm) x �.5�� (90mm) �.��1 �.5�� 0.��8 0.�01 �.9�7 1.65� 1.65� 0.�51 PP0�0�110090
�½" x �" �.9�1 (1�5mm) x �.�80 (6�mm)) �.9�1 �.�80 0.�80 0.1�� �.7�� 1.�60 0.6�0 0.�96 PP0�0�1�1506
�½" x �½" �.9�1 (1�5mm) x �.95� (75mm) �.9�1 �.95� 0.�80 0.169 �.858 1.�60 0.7�8 0.��6 PP0�0�1�5075
�½" x �" �.9�1 (1�5mm) x �.5�� (90mm) �.9�1 �.5�� 0.�80 0.�01 �.��1 1.61� 1.61� 0.596 PP0�0�1�5090
�½" x �" �.9�1 (1�5mm) x �.��1 (110mm) �.9�1 �.��1 0.�80 0.��8 �.9�7 1.65� 1.61� 0.579 PP0�0�1�5110
5" x �½" 5.51� (1�0mm) x �.95� (75mm) 5.51� �.95� 0.�15 0.169 5.�15 �.087 1.575 0.�6� PP0�0�1�0075
5" x �" 5.51� (1�0mm) x �.5�� (90mm) 5.51� �.5�� 0.�15 0.�01 5.118 �.087 1.65� 0.5�8 PP0�0�1�0090
5" x �" 5.51� (1�0mm) x �.��1 (110mm) 5.51� �.��1 0.�15 0.��8 �.7�� 1.�78 1.10� 0.�5� PP0�0�1�0110
5" x �" 5.51� (1�0mm) x �.9�1 (1�5mm) 5.51� �.9�1 0.�15 0.�80 7.087 1.�78 1.�60 0.�7� PP0�0�1�01�5
6" x �" 6.�99 (160mm) x �.5�� (90mm) 6.�99 �.5�� 0.�58 0.�01 5.��� �.087 1.61� 1.100 PP0�0�160090
6" x �" 6.�99 (160mm) x �.��1 (110mm) 6.�99 �.��1 0.�58 0.��8 5.0�9 �.087 1.61� 1.100 PP0�0�160110
6" x �½" 6.�99 (160mm) x �.9�1 (1�5mm) 6.�99 �.9�1 0.�58 0.�80 �.80� �.0�7 1.65� 1.067 PP0�0�1601�5
6" x 5" 6.�99 (160mm) x 5.51� (1�0mm) 6.�99 5.51� 0.�58 0.�15 �.7�� �.008 1.850 1.100 PP0�0�1601�0
7" x �" 7.087 (180mm) x �.5�� (90mm) 7.087 �.5�� 0.�0� 0.�01 5.709 �.087 1.65� 1.0�� PP0�0�180090
7" x �" 7.087 (180mm) x �.��1 (110mm) 7.087 �.��1 0.�0� 0.��8 5.906 �.165 1.65� 0.8�6 PP0�0�180110
7" x �½" 7.087 (180mm) x �.9�1 (1�5mm) 7.087 �.9�1 0.�0� 0.�80 5.6�0 �.0�7 1.65� 0.9�� PP0�0�1801�5
7" x 5" 7.087 (180mm) x 5.51� (1�0mm) 7.087 5.51� 0.�0� 0.�15 5.�15 �.0�7 1.850 0.70� PP0�0�1801�0
7" x 6" 7.087 (180mm) x 6.�99 (160mm) 7.087 6.�99 0.�0� 0.�58 5.51� 1.77� 1.575 0.70� PP0�0�180160
Reducer
Description: Reducer PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
D1D2
L1
L2
L
S2S1
(Continued on Next Page)
�8
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Reducer
Description: Reducer PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in Lbs Number
8" x 5" 7.87� (�00mm) x 5.51� (1�0mm) 7.87� 5.51� 0.��9 0.�15 5.709 �.��1 1.65� 1.0�� PP0�0���01�0
8" x 6" 7.87� (�00mm) x 6.�99 (160mm) 7.87� 6.�99 0.��9 0.�58 5.709 �.��1 �.0�7 1.958 PP0�0���0160
8" x 7" 7.87� (�00mm) x 7.087 (180mm) 7.87� 7.087 0.��9 0.�0� 5.709 �.��1 �.0�7 0.9�6 PP0�0���0180
9" x 5" 8.858 (��5mm) x 5.51� (1�0mm) 8.858 5.51� 0.50� 0.�15 5.906 �.��1 1.9�9 �.�87 PP0�0���51�0
9" x 6" 8.858 (��5mm) x 6.�99 (160mm) 8.858 6.�99 0.50� 0.�58 6.�99 �.559 �.087 �.519 PP0�0���5160
9" x 7" 8.858 (��5mm) x 7.087 (180mm) 8.858 7.087 0.50� 0.�0� 6.�99 �.5�0 �.��� �.618 PP0�0���5180
9" x 8" 8.858 (��5mm) x 7.87� (�00mm) 8.858 7.87� 0.50� 0.��9 6.�99 �.�80 �.087 �.�10 PP0�0���5�00
10" x 6" 9.8�� (�50mm) x 6.�99 (160mm 9.8�� 6.�99 0.559 0.�58 6.69� �.�80 �.087 �.�11 PP0�0��50160
10" x 7" 9.8�� (�50mm) x 7.087 (180mm) 9.8�� 7.087 0.559 0.�0� 6.890 �.5�0 �.�8� �.�98 PP0�0��50180
10" x 8" 9.8�� (�50mm) x 7.87� (�00mm) 9.8�� 7.87� 0.559 0.��9 7.087 �.5�0 �.5�0 �.960 PP0�0��50�00
10" x 9" 9.8�� (�50mm) x 8.858 (��5mm) 9.8�� 8.858 0.559 0.50� 7.�8� �.�6� �.165 �.158 PP0�0��50��5
11" x 8" 11.0�� (�80mm) x 7.87� (�00mm) 11.0�� 7.87� 0.6�6 0.��9 7.�8� �.559 �.559 5.19� PP0�0��80�00
11" x 9" 11.0�� (�80mm) x 8.858 (��5mm) 11.0�� 8.858 0.6�6 0.50� 7.87� �.756 �.165 5.��� PP0�0��80��5
11" x 10" 11.0�� (�80mm) x 9.8�� (�50mm) 11.0�� 9.8�� 0.6�6 0.559 7.87� �.8�5 �.��1 5.588 PP0�0��80�50
1�"x 8" 1�.�0� (�15mm) x 7.87� (�00mm) 1�.�0� 7.87� 0.705 0.��9 9.7�� �.150 1.969 7.08� PP0�0��15�00
1�"x 9" 1�.�0� (�15mm) x 8.858 (��5mm) 1�.�0� 8.858 0.705 0.50� 9.�70 �.�07 �.�6� 7.17� PP0�0��15��5
1�" x 10" 1�.�0� (�15mm) x 9.8�� (�50mm) 1�.�0� 9.8�� 0.705 0.559 9.17� �.�07 �.5�0 7.�16 PP0�0��15�50
1�" x 11" 1�.�0� (�15mm) x 11.0�� (�80mm) 1�.�0� 11.0�� 0.705 0.6�6 8.7�0 �.150 �.756 7.788 PP0�0��15�80
1�" x 9" 1�.976 (�55mm) x 8.858 (��5mm) 1�.976 8.858 0.791 0.50� 9.6�6 �.5�� 1.969 7.�0� PP0�0��55��5
1�" x 10" 1�.976 (�55mm) x 9.8�� (�50mm) 1�.976 9.8�� 0.791 0.559 9.6�6 �.5�� �.�6� 6.7�� PP0�0��55�50
1�" x 11" 1�.976 (�55mm) x 11.0�� (�80mm) 1�.976 11.0�� 0.791 0.6�6 9.6�6 �.5�� �.756 6.�9� PP0�0��55�80
1�" x 1�" 1�.976 (�55mm) x 1�.�0� (�15mm) 1�.976 1�.�0� 0.791 0.705 9.6�6 �.5�� �.150 6.160 PP0�0��55�15
D1D2
L1
L2
L
S2S1
(Continued on Next Page)
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�91.05�609
ChemicalProcess Piping Systems - Dimensional Data
Reducer
Description: Reducer PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
D1D2
L1
L2
L
S2S1
PN 6 / SDR 17.6
Nominal Actual OD D1 D2 S1 S2 L L1 L2 Weight Part
Size Size in in in in in in in Lbs Number
16" x 9" 15.7�8 (�00mm) x 8.858 (��5mm) 15.7�8 8.858 0.89� 0.50� 10.��6 �.7�0 �.�6� 10.1�0 PP0�0��00��5
16" x 10" 15.7�8 (�00mm) x 9.8�� (�50mm) 15.7�8 9.8�� 0.89� 0.559 10.��6 �.7�0 �.756 9.680 PP0�0��00�50
16" x 11" 15.7�8 (�00mm) x 11.0�� (�80mm) 15.7�8 11.0�� 0.89� 0.6�6 10.��6 �.7�0 �.756 9.0�0 PP0�0��00�80
16" x 1�" 15.7�8 (�00mm) x 1�.�0� (�15mm) 15.7�8 1�.�0� 0.89� 0.705 10.��6 �.7�0 �.150 7.9�0 PP0�0��00�15
16" x 1�" 15.7�8 (�00mm) x 1�.976 (�55mm) 15.7�8 1�.976 0.89� 0.791 10.��6 �.7�0 �.5�� 6.8�0 PP0�0��00�55
18" x 11" 17.717 (�50mm) x 11.0�� (�80mm) 17.717 11.0�� 1.00� 0.6�6 9.055 �.�6� �.756 1�.�00 PP0�0��50�80
18" x 1�" 17.717 (�50mm) x 1�.�0� (�15mm) 17.717 1�.�0� 1.00� 0.705 9.055 �.�6� �.150 11.880 PP0�0��50�15
18" x 1�" 17.717 (�50mm) x 1�.976 (�55mm) 17.717 1�.976 1.00� 0.791 9.055 �.�6� �.5�� 11.000 PP0�0��50�55
18" x 16" 17.717 (�50mm) x 15.7�8 (�00mm) 17.717 15.7�8 1.00� 0.89� 9.055 �.�6� �.7�0 9.680 PP0�0��50�00
�0" x 1�" 19.685 (500mm) x 1�.�0� (�15mm) 19.685 1�.�0� 1.118 0.705 9.055 �.�6� �.150 17.8�0 PP0�0�500�15
�0" x 1�" 19.685 (500mm) x 1�.976 (�55mm) 19.685 1�.976 1.118 0.791 9.055 �.�6� �.5�� 16.060 PP0�0�500�55
�0" x 16" 19.685 (500mm) x 15.7�8 (�00mm) 19.685 15.7�8 1.118 0.89� 9.055 �.�6� �.7�0 1�.7�0 PP0�0�500�00
�0" x 16" 19.685 (500mm) x 17.717 (�50mm) 19.685 17.717 1.118 1.00� 9.055 �.�6� �.�6� 1�.100 PP0�0�500�50
��" x 16" ��.0�7 (560mm) x 15.7�8 (�00mm) ��.0�7 15.7�8 1.��8 0.89� 9.055 �.�6� �.7�0 �1.780 PP0�0�560�00
��" x 18" ��.0�7 (560mm) x 17.717 (�50mm) ��.0�7 17.717 1.��8 1.00� 7.87� �.�6� �.�6� 18.9�0 PP0�0�560�50
��" x �0" ��.0�7 (560mm) x 19.685 (500mm) ��.0�7 19.685 1.��8 1.118 7.87� �.�6� �.�6� 16.7�0 PP0�0�560500
��" x 16" ��.80� (6�0mm) x 15.7�8 (�00mm) ��.80� 15.7�8 1.�06 0.89� 9.055 �.�6� �.7�0 ��.��0 PP0�0�6�0�00
��" x 18" ��.80� (6�0mm) x 17.717 (�50mm) ��.80� 17.717 1.�06 1.00� 7.87� �.�6� �.�6� �0.1�0 PP0�0�6�0�50
��" x �0" ��.80� (6�0mm) x 19.685 (500mm) ��.80� 19.685 1.�06 1.118 7.87� �.�6� �.�6� �6.�00 PP0�0�6�0500
��" x ��" ��.80� (6�0mm) x ��.0�7 (560mm) ��.80� ��.0�7 1.�06 1.��8 7.87� �.�6� �.�6� �1.560 PP0�0�6�0560
�8" x �0" �7.95� (710mm) x 19.685 (500mm) �7.95� 19.685 1.58� 1.118 7.�80 �.�07 1.575 �1.800 PP0�0�710500
�8" x ��" �7.95� (710mm) x ��.0�7 (560mm) �7.95� ��.0�7 1.58� 1.��8 6.69� �.189 1.575 �8.�80 PP0�0�7106�0
�8" x ��" �7.95� (710mm) x ��.80� (6�0mm) �7.95� ��.80� 1.58� 1.�06 5.51� �.795 1.575 �0.1�0 PP0�0�7106�0
�0" x ��" �1.�96 (800mm) x ��.0�7 (560mm) �1.�96 ��.0�7 1.78� 1.��8 7.87� �.��6 1.575 ��.��0 PP0�0�800560
�0" x ��" �1.�96 (800mm) x ��.80� (6�0mm) �1.�96 ��.80� 1.78� 1.�06 7.087 �.��6 1.575 51.�80 PP0�0�8006�0
�0" x �8" �1.�96 (800mm) x �7.95� (710mm) �1.�96 �7.95� 1.78� 1.58� 5.906 �.071 1.575 �1.580 PP0�0�800710
�0
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Description: Stub Ends PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
Stub Ends
PN 6 / SDR 17.6
Nominal Actual OD D S D3 D4 H1 h4 z1 Weight Part
Size Size in in in in in in in lbs Number
1½" 1.969 (50mm) 1.969 0.11� �.�6� �.��8 0.�7� 0.787 1.969 0.176 PP0�06050
�" �.�80 (6�mm) �.�80 0.1�� �.8�5 �.976 0.551 0.6�0 1.969 0.�18 PP0�0606�
�½" �.95� (75mm) �.95� 0.169 �.��5 �.7�� 0.6�0 0.787 1.969 0.�6� PP0�06075
�" �.5�� (90mm) �.5�� 0.�01 �.016 5.��6 0.669 1.69� �.150 0.598 PP0�06090
�" �.��1 (110mm) �.��1 0.��8 �.961 6.�99 0.709 1.65� �.�68 0.81� PP0�06110
�½" �.9�1 (1�5mm) �.9�1 0.�80 5.�76 6.�99 0.7�8 1.77� �.�65 0.7�8 PP0�061�5
5" 5.51� (1�0mm) 5.51� 0.�15 6.1�� 7.��1 0.709 1.5�5 �.�68 1.1�� PP0�061�0
6" 6.�99 (160mm) 6.�99 0.�58 6.9�9 8.��5 0.709 1.61� �.��8 1.�96 PP0�06160
7" 7.087 (180mm) 7.087 0.�0� 7.1�6 8.�86 0.8�7 �.��1 �.�68 1.��1 PP0�06180
8" 7.87� (�00mm) 7.87� 0.��9 9.17� 10.591 0.98� �.�8� �.76� �.�66 PP0�06�00
9" 8.858 (��5mm) 8.858 0.50� 9.��1 10.6�0 0.9�5 �.559 �.76� �.�1� PP0�06��5
10" 9.8�� (�50mm) 9.8�� 0.559 11.��0 1�.6�8 0.98� �.�0� �.7�� �.88� PP0�06�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 11.�96 1�.6�8 0.98� �.795 �.7�� �.��� PP0�06�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 1�.��8 1�.567 1.0�� �.��6 6.�57 6.51� PP0�06�15
1�" 1�.976 (�55mm) 1�.976 0.791 1�.7�� 17.008 1.181 �.898 7.��� 8.580 PP0�06�55
16" 15.7�8 (�00mm) 15.7�8 0.89� 16.850 19.055 1.�99 �.��1 7.8�5 1�.518 PP0�06�00
18" 17.717 (�50mm) 17.717 1.00� �0.��6 ��.071 1.811 �.5�0 5.51� ��.�96 PP0�06�50
�0" 19.685 (500mm) 19.685 1.118 �0.866 ��.0�1 1.850 �.6�8 5.551 �0.�60 PP0�06500
��" ��.0�7 (560mm) ��.0�7 1.��8 ��.�1� �6.969 1.969 �.�6� 5.551 �6.�00 PP0�06560
��" ��.80� (6�0mm) ��.80� 1.�06 �5.�76 �7.087 �.008 �.559 5.591 �5.55� PP0�066�0
�8" �7.95� (710mm) �7.95� 1.58� �9.016 �1.�96 1.969 1.969 5.906 �0.0�0 PP0�06710
�0" �1.�96 (800mm) �1.�96 1.78� ��.071 �5.6�0 �.0�7 1.890 5.906 5�.580 PP0�06800
��" �5.��� (900mm) �5.��� �.008 �7.165 �9.567 �.165 1.969 6.10� 66.660 PP0�06900
�9" �9.�70 (1000mm) �9.�70 �.��� �1.��0 ��.701 �.�6� 1.969 7.087 9�.�80 PP0�01000
D3 D D4
h4H1
z1
S
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�11.05�609
ChemicalProcess Piping Systems - Dimensional Data
Backing Ring
Description: Backing Ring 150 lbs. ANSI Drilling
Material: Glass Filled Polypropylene with Steel Core
Execution: Molded
Nominal B D D2 d6 K # Weight SIMTECH
Size in in in in in Holes lbs Part #
½" 0.�7� �.50� 0.6�0 1.��0 �.�6� � 0.�8� PP990700�0
¾" 0.�7� �.858 0.6�0 1.�19 �.756 � 0.660 PP990700�5
1" 0.6�0 �.�5� 0.6�0 1.6�� �.110 � 0.970 PP990700��
1¼" 0.6�0 �.606 0.6�0 1.988 �.50� � 1.188 PP990700�0
1½" 0.709 5.000 0.6�0 �.��1 �.858 � 1.�5� PP99070050
�" 0.709 5.98� 0.7�8 �.051 �.76� � 1.78� PP9907006�
�½" 0.709 7.008 0.7�8 �.�8� 5.51� � �.�18 PP99070075
�" 0.709 7.�80 0.7�8 �.�5� 5.98� 8 �.��0 PP99070090
�" & �½" 0.709 9.016 0.7�8 5.0�9 7.5�0 8 �.0�8 PP99070110
6" & 7" 0.9�5 11.0�� 0.87� 7.1�6 9.�88 8 6.��5 PP99070160
8" & 9" 0.9�5 1�.50� 0.87� 9.�70 11.7�� 8 10.�56 PP99070�00
10" & 11" 1.181 15.98� 1.000 11.516 1�.�5� 1� 1�.6�8 PP99070�50
1�" 1.��9 19.016 1.000 1�.�87 17.008 1� �6.��� PP99070�15
1�" 1.65� �0.98� 1.1�� 1�.78� 18.7�0 16 ��.5�0 PP99070�55
16" 1.7�� ��.50� 1.1�� 16.890 �1.�60 16 �8.7�0 PP99070�00
D2
D
B
d6
K
��
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Caps: Dome
Description: End Caps PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D S L Weight Part
Size Size in in in lbs Number
1½" 1.969 (50mm) 1.969 0.11� �.756 0.079 PP0��10050
�" �.�80 (6�mm) �.�80 0.1�� �.��8 0.1�5 PP0��1006�
�½" �.95� (75mm) �.95� 0.169 �.6�� 0.��1 PP0��10075
�" �.5�� (90mm) �.5�� 0.�01 �.17� 0.�7� PP0��10090
�" �.��1 (110mm) �.��1 0.��8 �.7�� 0.601 PP0��10110
�½" �.9�1 (1�5mm) �.9�1 0.�80 �.961 0.8�� PP0��101�5
5" 5.51� (1�0mm) 5.51� 0.�15 5.�5� 1.100 PP0��101�0
6" 6.�99 (160mm) 6.�99 0.�58 5.906 1.650 PP0��10160
7" 7.087 (180mm) 7.087 0.�0� 6.�99 �.��� PP0��10180
8" 7.87� (�00mm) 7.87� 0.��9 6.890 �.99� PP0��10�00
9" 8.858 (��5mm) 8.858 0.50� 7.87� �.9�9 PP0��10��5
10" 9.8�� (�50mm) 9.8�� 0.559 8.071 5.115 PP0��10�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 9.�5� 6.600 PP0��10�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 10.0�9 9.900 PP0��10�15
1�" 1�.976 (�55mm) 1�.976 0.791 11.0�� 1�.�88 PP0��10�55
16" 15.7�8 (�00mm) 15.7�8 0.89� 1�.�05 �1.6�6 PP0��10�00
D
S
L
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
��1.05�609
ChemicalProcess Piping Systems - Dimensional Data
Caps: Flat
Description: End Caps PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Machined
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D S L L1 Weight Part
Size Size in in in in lbs Number
10" 9.8�� (�50mm) 9.8�� 0.559 1.77� 1.��0 �.��� PP0�090�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 1.77� 1.�78 �.55� PP0�090�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 1.969 1.5�5 6.�68 PP0�090�15
1�" 1�.976 (�55mm) 1�.976 0.791 �.165 1.7�� 9.17� PP0�090�55
16" 15.7�8 (�00mm) 15.7�8 0.89� �.�6� 1.969 1�.11� PP0�090�00
18" 17.717 (�50mm) 17.717 1.00� �.756 �.�05 18.7�� PP0�090�50
�0" 19.685 (500mm) 19.685 1.118 �.95� �.��1 �5.5�0 PP0�090500
��" ��.0�7 (560mm) ��.0�7 1.��8 �.150 �.7�6 �5.�00 PP0�090560
��" ��.80� (6�0mm) ��.80� 1.�06 �.5�� �.071 50.�80 PP0�0906�0
�8" �7.95� (710mm) �7.95� 1.58� �.7�� �.016 7�.700 PP0�090710
�0" �1.�96 (800mm) �1.�96 1.78� 5.118 �.��1 10�.500 PP0�090800
D
S
LL1
��
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
lateral: 45°
Description: Lateral: 45° PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Fabricated
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D S L2 z2 z3 Weight Part
Size Size in in in in in lbs Number
�" �.��1 (110mm) �.��1 0.��8 �0.079 16.9�9 �.150 �.�98 PP0�170110
�½" �.9�1 (1�5mm) �.9�1 0.�80 �1.65� 17.717 �.9�7 �.88� PP0�1701�5
5" 5.51� (1�0mm) 5.51� 0.�15 ��.��8 18.50� �.7�� 7.�60 PP0�1701�0
6" 6.�99 (160mm) 6.�99 0.�58 �8.7�0 19.685 9.055 10.��0 PP0�170160
7" 7.087 (180mm) 7.087 0.�0� �0.709 �0.866 9.8�� 1�.��0 PP0�170180
8" 7.87� (�00mm) 7.87� 0.��9 ��.677 �1.65� 11.0�� 17.6�� PP0�170�00
9" 8.858 (��5mm) 8.858 0.50� ��.6�6 ��.8�5 11.811 ��.1�� PP0�170��5
10" 9.8�� (�50mm) 9.8�� 0.559 �7.008 ��.016 1�.99� �0.800 PP0�170�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 �9.�70 �5.591 1�.780 �1.800 PP0�170�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 ��.�07 �7.559 15.7�8 57.��0 PP0�170�15
1�" 1�.976 (�55mm) 1�.976 0.791 50.�9� ��.�65 16.9�9 75.680 PP0�170�55
16" 15.7�8 (�00mm) 15.7�8 0.89� 5�.150 �5.��� 17.717 10�.�80 PP0�170�00
18" 17.717 (�50mm) 17.717 1.00� 56.�99 �7.�0� 18.898 1�9.9�0 PP0�170�50
�0" 19.685 (500mm) 19.685 1.118 59.055 �9.�70 19.685 18�.�80 PP0�170500
��" ��.0�7 (560mm) ��.0�7 1.��8 6�.99� �1.��9 �1.65� ��5.�00 PP0�170560
��" ��.80� (6�0mm) ��.80� 1.�06 6�.961 ��.�07 �1.65� �99.�00 PP0�1706�0
D
D
S
L2
z2
z3 z2
45°
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�51.05�609
ChemicalProcess Piping Systems - Dimensional Data
lateral: 60°
Description: Lateral: 60° PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Fabricated
Connection: Butt Fusion
PN 6 / SDR 17.6
Nominal Actual OD D S L2 z2 z3 Weight Part
Size Size in in in in in lbs Number
�" �.��1 (110mm) �.��1 0.��8 19.685 1�.795 6.890 �.�88 PP0�165110
�½" �.9�1 (1�5mm) �.9�1 0.�80 �1.�57 1�.976 7.�80 �.7�0 PP0�1651�5
5" 5.51� (1�0mm) 5.51� 0.�15 ��.87� 1�.055 8.819 6.�0� PP0�1651�0
6" 6.�99 (160mm) 6.�99 0.�58 �5.�76 16.��0 9.055 8.866 PP0�165160
7" 7.087 (180mm) 7.087 0.�0� �7.559 17.717 9.8�� 1�.1�� PP0�165180
8" 7.87� (�00mm) 7.87� 0.��9 �9.88� 19.17� 10.709 16.5�� PP0�165�00
9" 8.858 (��5mm) 8.858 0.50� ��.677 �0.866 11.811 ��.000 PP0�165��5
10" 9.8�� (�50mm) 9.8�� 0.559 �5.6�0 ��.8�5 1�.795 �9.700 PP0�165�50
11" 11.0�� (�80mm) 11.0�� 0.6�6 �9.17� ��.80� 1�.�70 �0.�80 PP0�165�80
1�" 1�.�0� (�15mm) 1�.�0� 0.705 ��.91� �7.165 15.7�8 55.660 PP0�165�15
1�" 1�.976 (�55mm) 1�.976 0.791 �5.�7� �8.7�0 16.7�� 7�.�60 PP0�165�55
16" 15.7�8 (�00mm) 15.7�8 0.89� �9.�1� �1.�96 17.717 100.980 PP0�165�00
18" 17.717 (�50mm) 17.717 1.00� 5�.165 ��.�65 18.701 1�5.5�0 PP0�165�50
�0" 19.685 (500mm) 19.685 1.118 55.118 �5.��� 19.685 177.760 PP0�165500
��" ��.0�7 (560mm) ��.0�7 1.��8 58.�68 �7.�0� �0.866 ��8.1�0 PP0�165560
��" ��.80� (6�0mm) ��.80� 1.�06 60.8�7 �9.�70 �1.�57 �89.7�0 PP0�1656�0
D
D
S
L2
z2
z3 z2
60°
�6
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
45psi Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�71.05�609
ChemicalProcess Piping Systems - Dimensional Data
PN 3.2 / SRD 33
Nomnial Actual OD D S Weight Weight Part
Size Size in in (lbs./ m) Lbs. Foot Number
1½" 1.969 (50mm) 1.969 0.071 0.605 0.189 PP0�000050
�" �.�80 (6�mm) �.�80 0.079 0.8�0 0.�6� PP0�00006�
�½" �.95� (75mm) �.95� 0.091 1.16� 0.�6� PP0�000075
�" �.5�� (90mm) �.5�� 0.110 1.668 0.5�1 PP0�000090
�" �.��1 (110mm) �.��1 0.1�� �.�6� 0.770 PP0�000110
�½" �.9�1 (1�5mm) �.9�1 0.15� �.190 0.997 PP0�0001�5
5" 5.51� (1�0mm) 5.51� 0.169 �.960 1.��8 PP0�0001�0
6" 6.�99 (160mm) 6.�99 0.19� 5.10� 1.595 PP0�000160
7" 7.087 (180mm) 7.087 0.�17 6.�68 �.0�1 PP0�000180
8" 7.87� (�00mm) 7.87� 0.��� 8.096 �.5�0 PP0�000�00
9" 8.858 (��5mm) 8.858 0.�7� 10.05� �.1�� PP0�000��5
10" 9.8�� (�50mm) 9.8�� 0.�0� 1�.�7� �.898 PP0�000�50
11" 11.0�� (�80mm) 11.0�� 0.��9 15.598 �.87� PP0�000�80
1�" 1�.�0� (�15mm) 1�.�0� 0.�8� 19.7�� 6.167 PP0�000�15
1�" 1�.976 (�55mm) 1�.976 0.��9 ��.860 7.769 PP0�000�55
16" 15.7�8 (�00mm) 15.7�8 0.�8� �1.680 9.900 PP0�000�00
18" 17.717 (�50mm) 17.717 0.5�� �0.0�0 1�.51� PP0�000�50
�0" 19.685 (500mm) 19.685 0.60� �9.�80 15.�00 PP0�000500
��" ��.0�7 (560mm) ��.0�7 0.677 6�.0�0 19.�87 PP0�000560
��" ��.80� (6�0mm) ��.80� 0.760 78.��0 ��.�75 PP0�0006�0
�8" �7.95� (710mm) �7.95� 0.858 99.��0 �1.075 PP0�000710
�0" �1.�96 (800mm) �1.�96 0.965 1�5.8�0 �9.��5 PP0�000800
��" �5.��� (900mm) �5.��� 1.087 159.500 �9.8�� PP0�000900
�9" �9.�70 (1000mm) �9.�70 1.�05 196.��0 61.��5 PP0�0001000
PRESSURE PIPE
Description: Pressure Pipe PN3.2 / SDR 33 - 45psi
Material: Polypropylene
Execution: Extruded, Stress Relieved
Connection: Butt Fusion
D
S
�8
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
PN 3.2 / SDR 33
Nomnial Actual OD D S Le Z Weight Part
Size Size in in in in lbs Number
�" �.��1 (110mm) �.��1 0.1�� 0.�7� �.5�8 0.�88 PP0�010110
�½" �.9�1 (1�5mm) �.9�1 0.15� 0.�15 5.118 0.77� PP0�0101�5
5" 5.51� (1�0mm) 5.51� 0.169 0.�15 5.906 1.01� PP0�0101�0
6" 6.�99 (160mm) 6.�99 0.19� 0.709 6.575 1.58� PP0�010160
7" 7.087 (180mm) 7.087 0.�17 0.�15 7.��� �.��� PP0�010180
8" 7.87� (�00mm) 7.87� 0.��� 0.7�8 8.110 �.9�6 PP0�010�00
9" 8.858 (��5mm) 8.858 0.�7� 0.�9� 9.09� �.960 PP0�010��5
10" 9.8�� (�50mm) 9.8�� 0.�0� 0.787 10.079 5.1�8 PP0�010�50
11" 11.0�� (�80mm) 11.0�� 0.��9 0.�9� 11.�60 8.��8 PP0�010�80
1�" 1�.�0� (�15mm) 1�.�0� 0.�8� 0.866 1�.756 10.69� PP0�010�15
1�" 1�.976 (�55mm) 1�.976 0.��9 0.591 1�.961 1�.�98 PP0�010�55
16" 15.7�8 (�00mm) 15.7�8 0.�8� 0.98� 17.1�6 18.�16 PP0�010�00
Description: Elbow: 90° PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
Elbow: 90°
Z
D
Le
S
r=d
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
�91.05�609
ChemicalProcess Piping Systems - Dimensional Data
PN3.2 / SDR 33
Nominal Actual OD D S L L1 Z Weight Part
Size Size in in in in in lbs Number
�" �.��1 (110mm) �.��1 0.1�� 8.�65 1.969 �.1�� 0.880 PP0�0�0110
�½" �.9�1 (1�5mm) �.9�1 0.15� 8.58� �.�6� �.�1� 0.19� PP0�0�01�5
5" 5.51� (1�0mm) 5.51� 0.169 9.961 �.165 �.9�1 �.�88 PP0�0�01�0
6" 6.�99 (160mm) 6.�99 0.19� 10.6�0 �.6�� 5.51� �.189 PP0�0�0160
7" 7.087 (180mm) 7.087 0.�17 1�.�05 �.�65 5.906 �.10� PP0�0�0180
8" 7.87� (�00mm) 7.87� 0.��� 1�.�86 �.8�5 6.69� �.1�6 PP0�0�0�00
9" 8.858 (��5mm) 8.858 0.�7� 17.��� �.5�0 8.661 8.668 PP0�0�0��5
10" 9.8�� (�50mm) 9.8�� 0.�0� 17.��� �.5�0 8.�65 10.1�0 PP0�0�0�50
11" 11.0�� (�80mm) 11.0�� 0.��9 19.685 �.��8 9.567 1�.5�0 PP0�0�0�80
1�" 1�.�0� (�15mm) 1�.�0� 0.�8� �1.06� �.��8 10.6�0 18.810 PP0�0�0�15
1�" 1�.976 (�55mm) 1�.976 0.��9 �6.5�5 �.9�7 1�.661 �9.61� PP0�0�0�55
16" 15.7�8 (�00mm) 15.7�8 0.�8� �6.77� �.7�0 1�.�86 �5.��0 PP0�0�0�00
Tee
Description: Tee PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
ZD
L1
L
S
50
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
PN 3.2 / SDR 33
Nominal Actual OD D S D3 D4 H1 h4 z1 Weight Part
Size Size in in in in in in in lbs Number
�" �.��1 (110mm) �.��1 0.1�� �.9�1 6.��0 0.709 1.10� �.150 0.667 PP0�06110
�½" �.9�1 (1�5mm) �.9�1 0.15� 5.197 6.��0 0.709 1.�60 �.150 0.565 PP0�061�5
5" 5.51� (1�0mm) 5.51� 0.169 6.1�� 7.��1 0.709 1.�57 �.189 0.880 PP0�061�0
6" 6.�99 (160mm) 6.�99 0.19� 6.969 8.��5 0.709 1.575 �.�68 1.1�� PP0�06160
7" 7.087 (180mm) 7.087 0.�17 7.087 8.��6 0.709 1.77� �.150 1.0�� PP0�06180
8" 7.87� (�00mm) 7.87� 0.��� 9.17� 10.551 0.7�8 �.�8� �.76� �.585 PP0�06�00
9" 8.858 (��5mm) 8.858 0.�7� 9.��1 10.6�0 0.7�8 �.�80 �.7�� �.079 PP0�06��5
10" 9.8�� (�50mm) 9.8�� 0.�0� 11.��0 1�.598 0.787 �.�6� �.9�7 �.685 PP0�06�50
11" 11.0�� (�80mm) 11.0�� 0.��9 11.�96 1�.6�8 0.8�7 �.756 �.685 �.01� PP0�06�80
1�" 1�.�0� (�15mm) 1�.�0� 0.�8� 1�.��8 1�.567 0.8�7 �.��6 6.�57 �.�88 PP0�06�15
1�" 1�.976 (�55mm) 1�.976 0.��9 1�.7�� 17.0�7 0.9�5 �.858 7.165 5.65� PP0�06�55
16" 15.7�8 (�00mm) 15.7�8 0.�8� 16.850 19.055 1.0�� �.17� 7.795 8.118 PP0�06�00
18" 17.717 (�50mm) 17.717 0.5�� �0.��6 ��.0�1 1.�96 �.�6� �.7�� 16.060 PP0�06�50
�0" 19.685 (500mm) 19.685 0.60� �0.866 ��.071 1.5�5 �.��1 5.591 1�.6�0 PP0�06500
��" ��.0�7 (560mm) ��.0�7 0.677 ��.�1� �6.969 1.575 �.�6� �.7�� �0.0�0 PP0�06560
��" ��.80� (6�0mm) ��.80� 0.760 �5.�76 �6.969 1.575 �.�6� �.7�� 15.906 PP0�066�0
�8" �7.95� (710mm) �7.95� 0.858 �9.016 �1.�96 1.�78 1.969 5.�15 ��.0�� PP0�06710
�0" �1.�96 (800mm) �1.�96 0.965 ��.071 �5.6�0 1.�17 1.9�9 5.�15 �0.580 PP0�06800
��" �5.��� (900mm) �5.��� 1.087 �7.165 �9.567 1.575 1.969 5.51� �9.160 PP0�06900
�9" �9.�70 (1000mm) �9.�70 1.�05 �1.��0 ��.701 1.65� 1.890 6.�99 5�.680 PP0�061000
Description: Stub Ends PN6 / SDR 17.6 - 90psi
Material: Polypropylene
Execution: Molded
Connection: Butt Fusion
Stub Ends
D3 D D4
h4H1
z1
S
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
511.05�609
ChemicalProcess Piping Systems - Dimensional Data
Backing Ring
Description: Backing Ring 150 lbs. ANSI Drilling
Material: Glass Filled Polypropylene with Steel Core
Execution: Molded
D2
D
B
d6
K
Nominal B D D2 d6 K # Weight SIMTECH
Size in in in in in Holes lbs Part #
½" 0.�7� �.50� 0.6�0 1.��0 �.�6� � 0.�8� PP990700�0
¾" 0.�7� �.858 0.6�0 1.�19 �.756 � 0.660 PP990700�5
1" 0.6�0 �.�5� 0.6�0 1.6�� �.110 � 0.970 PP990700��
1¼" 0.6�0 �.606 0.6�0 1.988 �.50� � 1.188 PP990700�0
1½" 0.709 5.000 0.6�0 �.��1 �.858 � 1.�5� PP99070050
�" 0.709 5.98� 0.7�8 �.051 �.76� � 1.78� PP9907006�
�½" 0.709 7.008 0.7�8 �.�8� 5.51� � �.�18 PP99070075
�" 0.709 7.�80 0.7�8 �.�5� 5.98� 8 �.��0 PP99070090
�" & �½" 0.709 9.016 0.7�8 5.0�9 7.5�0 8 �.0�8 PP99070110
6" & 7" 0.9�5 11.0�� 0.87� 7.1�6 9.�88 8 6.��5 PP99070160
8" & 9" 0.9�5 1�.50� 0.87� 9.�70 11.7�� 8 10.�56 PP99070�00
10" & 11" 1.181 15.98� 1.000 11.516 1�.�5� 1� 1�.6�8 PP99070�50
1�" 1.��9 19.016 1.000 1�.�87 17.008 1� �6.��� PP99070�15
1�" 1.65� �0.98� 1.1�� 1�.78� 18.7�0 16 ��.5�0 PP99070�55
16" 1.7�� ��.50� 1.1�� 16.890 �1.�60 16 �8.7�0 PP99070�00
5�
ChemicalProcess Piping Systems - Dimensional Data
SIMTECHPhone: 877-777-2467 • Fax: 215-547-9129
www.SimtechUSA.com
1.05�609
Simtech Industrial Products, Inc. 47-A Runway Road, Levittown, PA 19057
Phone: 215-547-0444 Fax: 215-547-9129 E-mail: [email protected]
Web site: www.SimtechUSA.com
WARRANTY
Simtech Industrial Products, Inc. products are warranted to be free from defects in materials and workmanship for one (1) year from date of shipment. No claim shall be permitted under this warranty unless Buyer gives Simtech Industrial Products, Inc. written notice of all respects in which Buyer claims the product to be defective. Notice must be received within ten (10) days from the date which the Buyer discovers, or should have discovered the defect. Buyer shall give Simtech Industrial Products, Inc. a reasonable opportunity to inspect the product after notice has been given. This warranty shall not apply to any products or components, which have been subjected to abnormal use, negligence or accident.
Seller’s sole obligation under this warranty shall be limited solely on the repair or replacement, as elected by Simtech Industrial Products, Inc., of defective or nonconforming material. To the maximum extent permitted by law, Buyer irrevocably waives all claims for money damages relating to the condition, use and performance of the goods purchased. In no event shall Simtech Industrial Products, Inc. liability exceed the purchase price of the product sold by Simtech Industrial Products, Inc.
In no event, whether because of a breach of warranty or representation or any other cause, whether based upon contract, tort, warranty or otherwise, arising out of the performance or nonperformance by seller of its obligations under this agreement or with respect to the products sold pursuant here to; shall seller be liable for lost earnings, income or profits or indirect, incidental, liquidated or consequential damages.
The implied warranties of merchantability and fitness for a particular purpose except as set forth in this warranty, express or implied, are hereby disclaimed and excluded. Nothing shall be construed as an additional warranty unless specifically designated as such in writing and signed by Simtech Industrial Products, Inc.
Simtech Industrial Products, Inc. reserves the right, in its discretion, at any time and from time to time, to make changes to any specification, data or information contained herein.