Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of...
-
Upload
brent-parrish -
Category
Documents
-
view
245 -
download
0
Transcript of Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of...
![Page 1: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/1.jpg)
Chapter 7 Control Systems Design by Root-Locus Method
7.1 Introduction- The primary objective of this chapter is to present procedures
for the design and compensation of single-input-single-output linear time-invariant control systems.
- Compensation is the modification of the system dynamics to satisfy the given specifications.
Performance Specifications
- Transient response requirements such as the maximum overshoot and settling time in step response.
- Steady-state requirements such as steady-state error in following ramp input.
![Page 2: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/2.jpg)
- The adjustment of the gain: increasing the gain value will improve the steady-state behavior but will result in poor stability or even instability.
- Compensation: to redesign the system by modifying the structure or by incorporating additional devices or components to alter the overall behavior so that the system.
![Page 3: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/3.jpg)
- Compensator: A device inserted into the system for the purpose of satisfying the specifications.
Figure 7-1 (a) Series compensation; (b) parallel or feedback compensation.
![Page 4: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/4.jpg)
![Page 5: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/5.jpg)
![Page 6: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/6.jpg)
Figure 7-2 (a) Root-locus plot of a single-pole system; (b) root-locus plot of a two-pole system; (c) root-locus plot of a three-pole system.
![Page 7: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/7.jpg)
Figure 7-3 (a) Root-locus plot of a three-pole system; (b), (c), and (d) root-locus plots showing effects of addition of a zero to the three-pole system.
![Page 8: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/8.jpg)
Figure 7-4 Electronic circuit that is a lead network if R1 C1 > R2 C2 and a lag network if R1 C1 < R2 C2 .
![Page 9: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/9.jpg)
![Page 10: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/10.jpg)
Figure 7-5 Pole-zero configurations: (a) lead network; (b) lag network.
![Page 11: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/11.jpg)
- Specification: damping ratio and undamped natural frequency of the desired dominant closed-loop poles, maximum overshoot, rise time, and settling time.
- Problem: unstable for all val- ues of gain or is stable but has undesirable transient-response characteristics.
![Page 12: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/12.jpg)
![Page 13: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/13.jpg)
- If a large static error constant is required, cascade a lag network or alter the lead compensator to a lag-lead compensator.
![Page 14: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/14.jpg)
![Page 15: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/15.jpg)
![Page 16: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/16.jpg)
![Page 17: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/17.jpg)
![Page 18: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/18.jpg)
![Page 19: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/19.jpg)
![Page 20: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/20.jpg)
![Page 21: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/21.jpg)
![Page 22: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/22.jpg)
- If we choose R2C2 > RIC1 in the circuit shown in Figure 7-4, it becomes a lag compensator.
![Page 23: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/23.jpg)
![Page 24: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/24.jpg)
![Page 25: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/25.jpg)
![Page 26: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/26.jpg)
![Page 27: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/27.jpg)
![Page 28: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/28.jpg)
![Page 29: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/29.jpg)
Figure 7-14 Compensated system.
Figure 6-50 (a) Root-locus plots of the compensated system and uncompensated system; (b) root-locus plot of compensated system near the origin.
![Page 30: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/30.jpg)
![Page 31: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/31.jpg)
![Page 32: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/32.jpg)
![Page 33: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/33.jpg)
![Page 34: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/34.jpg)
![Page 35: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/35.jpg)
Figure 7-16 Unit-ramp responses of compensated and uncompensated systems. [The compensator is given by Equation (6–20).]
![Page 36: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/36.jpg)
![Page 37: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/37.jpg)
Figure 7-17 Unit-step responses of compensated and uncompensated systems. [The compensator is given by Equation (6–20).]
![Page 38: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/38.jpg)
![Page 39: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/39.jpg)
Figure 7-18 Lag–lead compensator.
![Page 40: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/40.jpg)
![Page 41: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/41.jpg)
![Page 42: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/42.jpg)
![Page 43: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/43.jpg)
![Page 44: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/44.jpg)
![Page 45: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/45.jpg)
![Page 46: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/46.jpg)
![Page 47: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/47.jpg)
Figure 7-21 (a) Root-locus plot of the compensated system; (b) root-locus plot near the origin.
![Page 48: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/48.jpg)
Figure 7-22 Transient-response curves for the compensated system and uncompensated system. (a) Unit-step response curves; (b) unit-ramp response curves.
![Page 49: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/49.jpg)
![Page 50: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/50.jpg)
![Page 51: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/51.jpg)
![Page 52: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/52.jpg)
![Page 53: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/53.jpg)
Figure 7-23 Determination of the desired pole-zero location.
![Page 54: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/54.jpg)
![Page 55: Chapter 7 Control Systems Design by Root-Locus Method 7.1 Introduction -The primary objective of this chapter is to present procedures for the design and.](https://reader036.fdocuments.us/reader036/viewer/2022081417/56649e535503460f94b4921d/html5/thumbnails/55.jpg)
Figure 7-24 (a) Unit-step response curves for the compensated and uncompensated systems; (b) unit-ramp response curves for both systems.