Chapter 5 beams design
-
Upload
simon-foo -
Category
Engineering
-
view
108 -
download
1
Transcript of Chapter 5 beams design
![Page 1: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/1.jpg)
CHAPTER 5: BEAM DESIGN
0 Steel Beam Design
0 Timber Beam Design
Jan - May 2017 1
![Page 2: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/2.jpg)
Beam
The most frequently used and possibly the earliest used, structural element is beam.
Loading can be imposed on a beam from one or several of a number of sources , e.g. other secondary beams, columns, walls, floor systems or directly from installed plant or equipments.
Jan - May 2017 2
![Page 3: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/3.jpg)
Steel Beam
Jan - May 2017 3
![Page 4: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/4.jpg)
Jan - May 2017 4
![Page 5: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/5.jpg)
Jan - May 2017 5
![Page 6: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/6.jpg)
Steel BeamDesign Procedure (General)
The general steps in a beam design include: For ultimate limit state:
a) shear capacity – shear force due to the design loading must not exceed the shear capacity, the buckling due to shear also should be considered in some circumstance;
b) moment capacity – bending moments due to the design loading must not exceed the moment capacity. The reduction moment due to high shear and lateral torsional buckling due to insufficient restraint also required appropriate concern;
c) local buckling and bearing – when loads or reactions are applied through the flange to the web, the local resistance of the web should not be exceeded.
For serviceability limit state
a) deflection – the deflection due to design loading should not exceed the limits given in Table 8, BS 5950-1:2001
Jan - May 2017 6
![Page 7: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/7.jpg)
0 The design path shown in Figure 5-1 below provides ageneral view of the necessary procedure in designinga beam.
Jan - May 2017 7
![Page 8: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/8.jpg)
Figure 5-1 Flow chart of a beam designJan - May 2017 8
![Page 9: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/9.jpg)
The shear force Fv, should not be greater than the shear capacity Pv
given by:
Pv = 0.6yAv
Where Av is
a) rolled I, H and channel sections, load parallel to web: tD
b) welded I-sections, load parallel to web: td
c) any other cases: 0.9A0
A0 is the area of that rectilinear element of the cross-section which has the largest dimension in the direction parallel to the shear force, see Figure 5-2.
Jan - May 2017 9
![Page 10: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/10.jpg)
The d/t ratio also needs to be checked due to the strength of the web will be governed by its resistance to shear buckling if it is too high.
Provided in cl. 4.2.3. for a rolled section, the web should be checked for shear buckling when d/texceeds 70√(275/py) where the d is the web depth clear of the fillets.
Average shear stress on web = shear force/web area = V/ (D x t)
Jan - May 2017 10
![Page 11: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/11.jpg)
Shear failure in concrete beam Failure in steel beam
Jan - May 2017 11
![Page 12: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/12.jpg)
Moment Capacity
Mult = y x S
where Mult = ultimate moment
y = ultimate yield stress
S = plastic section modulus
Jan - May 2017 12
![Page 13: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/13.jpg)
Table 1: Universal Steel Beams (Dimension and Properties)
Jan - May 2017 13
![Page 14: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/14.jpg)
Example 1
0 A 254 x 146 x 31 kg/m universal beam is used as a 3 m longcantilever. What is the maximum ultimate load that can beapplied at the end of the cantilever if the steel yields at astress of 275 N/mm2?
Jan - May 2017 14
![Page 15: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/15.jpg)
Solution
Mult = y x S
= 275 x 395/103
= 108.63kNm
Mult = 3 x F
3F = 108.63
F = 36.3 kN
Jan - May 2017 15
![Page 16: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/16.jpg)
A single span beam is simply supported between two columns and carriesa reinforced concrete slab as shown in Figure below. Using the design loadindicated, determine the dimensions of suitable standard universal beam.Assume S275 steel.
Example 2
13.7 kN/m
6m
a) Universal Beam SectionJan - May 2017 16
![Page 17: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/17.jpg)
Solution :
a) Design a suitable universal beam section
Solution
13.72kN/m
AB
6 m
Step 1: Determine reaction at support
Reaction RA = RB= (13.72 x 6)/2 = 41.2 kNMmax = wL2/8 = 13.72 x 62 /8 = 61.74 kNm
Jan - May 2017 17
![Page 18: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/18.jpg)
Solution :
Step 2
Draw a shear force diagram
Solution
41.2
41.2
Step 3Draw a bending moment diagram
61.74
Jan - May 2017 18
![Page 19: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/19.jpg)
Solution :
Step 4 : Calculation
A typical yield stress for mild steel is 275 N/mm2
S = Mult/ y = 61.74 x 106/ 275 x 103 = 224.5 cm3
Try 254 x 102 x 22 kg/m universal beam
( S = 262 cm3, D = 254 mm, t = 5.8 mm)
Average shear stress = 41.2 x 103/ 254 x 5.8 = 28 N/mm2 ( < 165N/mm2)
Use 254 x 102 x 22 kg/m universal beam
Example 2 : Full Lateral Restraint Beam
Jan - May 2017 19
![Page 20: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/20.jpg)
A simply supported 406 x 178 x 74 UB S275 is required tospan 4.5 and to carry an ultimate design load of 40 kN/m.Check the suitability of the section with respect the shear.
Solution :
Section properties : 406 x 178 x 74 UB S275
t= 9.7 mm, D= 412.8 mm, d= 360.4 mm, d/t = 37.2
Design shear force at the end of beam Fv = (40 x 4.5)/2= 90kN
Clause 4.2.3: Pv = 0.6 yAv
For a rolled UB section Av = tD = 9.7 x 412.8 = 4 004 mm2
Example 3 : Shear check of a Simply Supported Beam
Jan - May 2017 20
![Page 21: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/21.jpg)
Solution :
Clause 4.2.3 : Pv = 0.6yAv = 0.6x275x4 004/1000
= 661 kN > Fv = 90 kN
Shear is adequate
Example 3 : Shear check of a Simply Supported Beam
Jan - May 2017 21
![Page 22: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/22.jpg)
A single span beam is simply supported between two columns andcarries a reinforced concrete slab in addition to the column and loadingshown below. Using the design load indicated, select a suitable sectionconsidering section classification, shear and bending only. Assume S275steel and that dead loads are inclusive of self-weights.
Exercise
41.2 kN
3.17 kN/m
3 m 3 m
Universal Beam Section
Jan - May 2017 22
![Page 23: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/23.jpg)
Jan - May 2017 23
![Page 24: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/24.jpg)
Timber Beam
Glue Laminated Timber
Jan - May 2017 24
![Page 25: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/25.jpg)
Timber Beam
Space Beam
• Blocked and securely nailed at frequent
intervals to enable individual member to
act as an integral unit.
Jan - May 2017 25
![Page 26: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/26.jpg)
Timber Joists
Small timber beams are often used in the floor construction of houses, where they are known as joists.
Jan - May 2017 26
![Page 27: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/27.jpg)
Timber Joists
Jan - May 2017 27
![Page 28: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/28.jpg)
TIMBER JOISTS
Jan - May 2017 28
![Page 29: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/29.jpg)
Timber Joists
Jan - May 2017 29
![Page 30: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/30.jpg)
ExampleFigure below shows a house floor which uses 50 mm wide x 150 mm
deep timber joists spaced at 400 mm centres. If the maximum
permissible stress in the timber is limited to 7.5 N/mm2 , determine the
maximum allowable simply supported span of the floor if it supports the
following loads:
Dead load of floor = 0.45 kN/m2
Imposed load on floor = 1.5 kN/m2
Jan - May 2017 30
![Page 31: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/31.jpg)
Solution:
Total load = 0.45 + 1.5 = 1.95 kN/m2
Load/m, w on each joist = 1.95 x 0.4 = 0.78 kN/m
For a simply supported floor joist with a uniformly distributed load:
M = wL2/8
= 0.78 L2/8
For a beam with a rectangular cross-section:
Elastic section modulus Z = BD2/6
= 50 x 1502 /6
= 187 500 mm3
From above M = max x Z = 7.5 x 187 500
= 1 406 000 Nmm
= 1.406 kNm
Equating the two values of M:
1.406 = 0.78 L2/8
L = 3.79 m
Allowable span = 3.79 mJan - May 2017 31
![Page 32: Chapter 5 beams design](https://reader036.fdocuments.us/reader036/viewer/2022081721/5a64ce0c7f8b9ac21c8b6325/html5/thumbnails/32.jpg)
Exercise
32
Question 1
What is the origin of the word ‘Glulam’. Described how Glulam ismanufactured. State one structural advantages that Glulam has overconventional solid timber. State one example of the type of structural form thatcan be constructed from Glulam in buildings.