Chapter 3 Flows Around Submerged Bodies
-
Upload
prya-suthan-sathiananthan -
Category
Documents
-
view
57 -
download
6
description
Transcript of Chapter 3 Flows Around Submerged Bodies
-
CChhaapptteerr
FFLLOOWWSS AARROOUUNNDD SSUUBBMMEERRGGEEDD BBOODDIIEESS
33
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
2
Characteristics of External Flows Characteristics of External Flows Boundary Layers Boundary Layers Boundary Layer Theory for Flat Plate Boundary Layer Theory for Flat Plate Drag Drag Lift Lift
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
3.1 CHARACTERISTICS OF EXTERNAL FLOWS
External flow refers to flows around a closed solid body, not constrained by boundaries and without free surfaces.
Figure 3.1 External flow for 2D, axisymmetric and 3D cases
The characteristics of the flow is determined by the local Reynolds Number:
UxUx
x ==Re (3.1)
where U is the upstream velocity and x the characteristic length.
3
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.2 Pressure and wall shear stress distribution of an airfoil
The fluid-body interaction on the surface of the body leads to wall shear stresses w due to viscous effects and pressure p.
4
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure3.3 Shear and pressure force distribution on area dA
The force analysis on an elemental area dA in the above figure yields: ( ) ( )( ) ( )
cossin
sincosdAdApdF
dAdApdF
wy
wx
+=+=
5
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Therefore, drag D and lift L could be obtained:
+== dAdApdFD wx sincos (3.2) +== dAdApdFL wy cossin (3.3) Forces D and L are known as aerodynamic (for air/gas) or
hydrodynamic (for water/liquid) forces.
Experimentally, p, w, D and L can be made related to dynamic pressure 221 U : Local Pressure Coefficient:
221 U
ppC p = (3.4)
6
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Local Friction Coefficient:
221 U
c wf = (3.5)
Drag Coefficient:
AUDCD 2
21 = (3.6)
Lift Coefficient:
AULCL 2
21 = (3.7)
7
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
EXAMPLE 3.1
Water flows past an equal triangular bar as shown in the figure below. Using the given pressure distribution and neglecting shear forces, calculate the drag and lift on the bar.
8
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Drag (w = 0):
( )
( )( ) ( ) ( )[ ]( )( ) ( ) N 0.4603.02.16.19985.0
5.025.025.0
5.0225.01
60cos2180cos
60cos60cos180cos
sincos
2
222
221
212
21
321
===+=
+=+=
++=+=
AUAUAU
AUAU
dApdAp
dApdApdAp
dAdApD w
Since body is symmetry:
0=L
9
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
3.2 BOUNDARY LAYERS
Figure 3.4 Boundary layers for 3 different values of Rel
10
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Boundary layer is the region around the surface of a body where viscous effects are dominant ( )UV 99.0< .
Outside of the boundary layer, the flow could be assumed inviscid. Flows with high velocity (high Re) could lead to circulation or wakes
downstream of the body.
For a blunt body, such as cylinders, flow separation could occur starting from a separation point or location.
11
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.5 Boundary layers around a cylinder for 3 different ReD values
12
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
There are 3 parameters used to represent boundary layer: 1. Boundary layer thickness value of y where V , U99.0===
ll
U
Hence, flow is turbulent. Boundary layer thickness:
( )( )
mm 50.6m 006498.036.001805.0
01805.010298.4
16.0Re
16.071671
====
==
ll
35
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
(b) Drag needs to be calculated for both surfaces of the hydrofoil:
Case (i) Consider the smooth turbulent curve:
( )0034970
10298.4
031.0Re
031.071671
.
C fD
=
==l
( )( )( )( )( ) ( )
N 6.3218.036.01299800349702
22
21
221
==
=.
AUCD Df
Case (ii) Consider the transition curve Rel = 5 105:
003162010298.4
14400034970Re1440
Re031.0
671
.
.C fD
=== ll
36
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
( )( )( )( )( ) ( )
N 9.4218.036.01299800316202
22
21
221
==
=.
AUCD Df
Case (iii) Consider the relative roughness:
0064670360122.0log62.189.1log62.189.1
5.25.2
.
C fD
=
=
=
l
( )( )( )( )( ) ( )
N 0.2618.036.01299800646702
22
21
221
==
=.
AUCD Df
37
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
3.4 DRAG
In actual situations, distribution of pressure p and shear stress w in Eq. (3.2) below, are difficult to obtain analytically:
+= dAdApD w sincos Alternatively, D is assumed proportional to 221 U with the
proportionality coefficient being the drag coefficient CD obtained from graphs:
AUDCD 2
21 = (3.23)
38
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
From Eq. (3.2), drag could be divided into two components: > Pressure drag
AUCdApD Dpp2
21cos ==
> Friction drag AUCdAD Dfwf
221sin ==
Thus,
DfDpD CCC +=
39
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
In the equation above, area A could be either one of the following: > Frontal area projected area of the body as seen from the stream
(for stubby bodies with large shape ratio),
> Planform area projected area of the body as seen from above (suitable for thin bodies with large surface area or flat-shaped),
> Wetted area for bodies that float and move on free surfaces.
Factors that influence CD is given by the relationship: ( )lFr,Ma,Re,,shape=DC
For shape factors, blunt bodies have larger CD compared to streamlined shaped bodies.
40
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.10 Effect of geometry on drag coefficient
41
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.11 Evolution in design of cars with aerodynamic characteristics
For Re factors, D is dependant on upstream velocity U, characteristic length l and fluid viscosity .
42
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
For low Re, it could derived: ( )
Re22
,,
222221
Analysis lDimensiona
CUCU
UDC
CUDUfD
D ==== =
ll
l
ll
Figure 3.12 Drag coefficient CD for low Re flows
43
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.13 Relation between the drag coefficient of cylinder/sphere and
Reynolds number Re
44
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.13 (continued)
45
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.14 Drag coefficient as a function of Re for other bodies
46
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
For Ma effects, greater change in density (proportional to Ma refer chapter 9) increases CD.
Figure 3.15 Drag coefficient as a function of Ma for subsonic flow
47
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.16 Drag coefficient as a function of Ma for supersonic flow
48
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
For Fr factors, it only applies to bodies floating on free surfaces.
Figure 3.17 Drag coefficent as a function of Fr
49
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
For the effect of wall surface roughness, roughness increases CD.
Figure 3.18 Drag coefficient for smooth and rough sphere
50
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.19 Drag coefficient of some 2D objects for Re 104
51
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.20 Drag coefficient of some 3D objects for Re 104
52
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
EXAMPLE 3.4
Wind at 100 km/hr blows past a smooth surfaced water tower as shown in the figure below. Estimate the reacting moment required to avoid the tower from tipping over. Use air density = 1.23 kg/m3 and viscosity of air = 1.79 105 kg/m3.
53
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Reynolds No. for the sphere and cylinder: ( )
( )6
5
7
5
10589.836001000100
1079.15.423.1Re
10386.236001000100
1079.15.1223.1Re
=
===
==
cc
ss
Ud
Ud
Calculation of drag for the sphere and cylinder:
9.0,35.0 cDsD CC
( )( ) ( )N 20382
5.1243600
100010023.135.0 22
21
221
=
=
= ssDs AUCD
54
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
( )( ) ( )( )N 28828
5.4153600100010023.19.0
2
21
221
=
=
= ccDc AUCD
From the free body diagram:
mkN 649mN 10493.6
21528828
25.121520382
22
5
==
+
+=
+
+= bDdbDM css
55
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
3.5 LIFT
Similar to drag D, the distribution of pressure p and shear stress w in Eq. (3.3) shown below, are difficult to obtain analytically:
+= dAdApL w cossin Similar to drag D, the lift L could also be assumed proportional to
221 U with the proportionality constant being the lift coefficient CL:
AULCL 2
21 = (3.24)
The equation to determine L was developed by Kutta (1902) and Joukowski (1906), known as Kutta-Joukowski lift theorem:
= UbL (3.25)
56
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
with being the circulation as described in Chapter 2: ( ) ++== CC dzwdyvdxudsV (3.26)
The factors that influence CL is similar as those factors effecting CD: ( )lFr,Ma,Re,,shape=LC
Figure 3.22 Symetrical and nonsymmterical aerofoil
57
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
58
A symmetrical body produces L = 0, and L 0 could only happen if angle of attack > 0.
Most applications involved with the principle of lift operates at high Re ( 104) flows where w effects could be neglected.
Therefore, lift L is more dependant on the distribution of surface pressure p.
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.23 Distribution of surface pressure on a car
In aerofoils, the reference area is the projected plan area A = bc, where c is the chord dimension and b is the span dimension.
59
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.24 Configuration of an aerofoil
In general, increase in angle of attack increases CL and CD. ( ) DL , However, that is too large generates turbulent wakes
causing aerofoils to stall.
60
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.25 Relationship of CL and CD with angle of attack
61
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Figure 3.26 Relationship between CL and CD
62
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Addition of wing structures (flap/aileron) could alter the lift and drag characteristics of an aerofoil.
Figure 3.27 Effect of wing structures to an aerofoil
63
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
64
EXAMPLE 3.5
Given below is the data for a glider flying through the atmospheric space:
Glider velocity U = 5 m/s Wing size b = 30 m, c = 2.5 m (average) Weight (including pilot) W = 950 N Drag coefficient CD = 0.046 (based on plan area) Efficiency of glide power = 0.8 (for drag resistance)
Determine the lift coefficient and required power of the glider to maintain the velocity at similar altitude. Use density of air = 1.23 kg/m3.
-
FLOWS AROUND SUBMERGED BODIES KKKJ3123 FLUID MECHANICS
Equilibrium at the same altitude level: AUCLW L
221 ==
Hence, the lift coefficient:
( )( ) ( )( )
824.05.230523.1
9502222
===
bcUWCL
Power/efficiency relation for glider:
( )UAUCDUP D 221 == ( )( ) ( )( )
( ) W332
8.025.230523.1046.0
2
33
===
AUCP D
65
Chapter 3 Flows Around Submerged Bodies3.1 Characteristics of External FlowsExample 3.1
3.2 Boundary Layers3.3 Boundary Layer Theory for Flat PlateExample 3.2Example 3.3
3.4 DragExample 3.4
3.5 LiftExample 3.5