Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
Transcript of Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
1/11
HUAWEI
Training Objective
Quidway backup center function
Backup center basic concept
Quidway backup center configuration
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
2/11
HUAWEI
What Is Backup Center
The module in Quidway routers to manage backup
function
Network reliability and usability can be improved byusing backup center
Use backup center to provide backup for a router
interface
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
3/11
HUAWEI
Function of Backup Center
Can provide backup interface for any interface on a router (except dialer interface)
Any interface on a router can be taken as the backup interface of other interfaces (or logic channels)
Can provide backup to a certain logic channel on a interface. The backup interface can be an interfaceand can also be a certain logic channel on the interface (the logic channel referred here can be thevirtual circuit of X.25 and frame relay, and can also be a certain dialer map of a dialer interface)
For a main interface, can provide it with many backup interfaces. When a fault happens to the maininterface, these backup interfaces can decide a usage sequence according to their priorities
For an interface with many logic channels (such as BRI and PRI interfaces), can provide backup forseveral main interfaces.
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
4/11
HUAWEI
Enter into the configuration mode of a main interface that uses backup functionSpecify the backup interface and its priority used by the main interface
Configure switchover condition between main and backup interfaces (optional)
Set state-judging conditions when the main interface is a logic channel (optional)
Set state-judging conditions when the backup interface is a logic channel (optional)
Configure routes for main and backup interfaces. No matter using dynamic route or static route,the main and backup interfaces all need to have a route to reach destination network
Backkup Center Configuration Task List
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
5/11
HUAWEI
The main interface is a physical interface
interface interface-type interface-numberThe main interface is a logic channel
x25 map protocol address x.121-address [ linlogic-channel-number]frame-relay mapprotocol address dlci [ lin
logic-channel-number]
dialer mapprotocol next-hop-address dialer-string
[ lin logic-channel-number]logic-channel logic-channel-number
Enter into Main Interface Configuration Mode
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
6/11
HUAWEI
Specify a logic channel to backup a main interface, and set its prioritybackup logic-channelnumber [priority]
Specify a physical interface to backup a main interface, and set its prioritybackup interfaceinterface-type interface-number [ priority]
Establish a corresponding relation between virtual circuit and logic channel
Specify a logic channel number for X.25 virtual circuitx25 mapprotocol address x.121-address [ linlogic-channel-number]
Specify a logic channel number for frame relay virtual circuitframe-relay mapprotocol address dlci[ lin logic-channel-number]
Specify a logic channel number for dialer mapdialer mapprotocol next-hop-address dialer-string[ linlogic-channel-number]
Specify Standby Interface and Priority
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
7/11
HUAWEI
Setting delay time for switchover between mainand backup interfaces
backup delay { enable-delay}{ disable-delay}
Note: this command only applies to the situationwhen the main interface is a physical interface!
Configure Switchover Condition between Mainand Backup Interfaces
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
8/11
HUAWEI
Set the condition for judging the logical channel as down: the logical channel is regarded as down afterthe specified number of unsuccessful calls.
backup state-down number
After systemswitches to backup interface, interval-timeis set to make regular inspections so as tocheck whether the original logical channel has recovered its "up" state.
backup state-up interval-t ime
Setting State-judging Condition When theMain Interface Is a Logic Channel
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
9/11
HUAWEI
Configuration Example (1)
PSTN
Quidway 2501 Quidway 2501
IP 129.102.0.1 IP 129.102.0.2
IP 10.110.0.1IP 10.110.0.2
outer1
Tel:8810025
Router2
Tel:8810026
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
10/11
HUAWEI
Configuration Example (2)
uidway 2501 Quidway 2501
IP 129.102.0.1 IP 129.102.0.2
IP 10.110.0.1 IP 10.110.0.2
x.25
1000 2000
PPP
-
7/27/2019 Chapter 11 Backup Center Principle and ConfigurationV2.0.PDF
11/11
HUAWEI
Summary
Grasp the concept and principle (theswitchover process between main andbackup interfaces) of backup center.
Grasp backup center function (to know whichinterfaces can participate in backup).
Grasp backup configuration commands, anddistinguish differences between physicalinterface and logic interface.