Ch5- SS7 [相容模式]
Transcript of Ch5- SS7 [相容模式]
![Page 1: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/1.jpg)
Signaling System
![Page 2: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/2.jpg)
2
Reference (1/2)
[1] Wireless and Mobile Network Architectures,Y-Bing Lin and Imrich Chlamtac,Wiley Computer Publishing。 Chapters 2 and 5.
[2] 第七號共通信號系統概論,湯鴻沼,全華科技圖書股份有限公司。
[3] Telephone Network and PBX Software ,Yi-Bing Lin,維科出版社。
[4] Mobile and Wireless Networks,Uyless Black,Prentice Hall。Appendix A.
![Page 3: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/3.jpg)
3
Reference (2/2)
[5] SS7信號系統,林添財,中華電信訓練所教材。
[6] Carrier Grade Voice over IP,2nd,Daniel Collins,Mc Graw-Hill Companies Inc.。
[7]Signaling System #7, 2nd, Travis Russell, McGraw-Hill.
![Page 4: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/4.jpg)
4
Outlines
Introduction Signaling System Number 7 Components and Links of SS7 SS7 Protocol Stack SS7 Messages PCS/PSTN Call Control Using ISUP Summary
![Page 5: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/5.jpg)
Introduction
• PSTN
• SS7 Network Architecture
• SS7 Components
![Page 6: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/6.jpg)
6
PSTN Architecture
ISDN Adaptor
CO ISDN CO
ISDN PBX
PBX
TrunkTrunk
Trunk (ex: E1) Primary
Rate Interface
Basic Rate Interface
Subscriber Line
CO
Trunk
Trunk
TrunkCOTandem Tandem
![Page 7: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/7.jpg)
7
Components in PSTN
Customer premises equipment (CPE) Telephone set, PBX (Private Branch Exchanges),
ISDN (Integrated Services Digital Network) PBX, ISDN Adaptor
Transmission facilities Trunks and subscriber lines
Switching system Central offices (CO) or exchange, tandems, ISDN
CO
![Page 8: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/8.jpg)
8
Call Setup and Release
A call requires a communications circuit between two subscribers.
The setup and release of connection is triggered by signals.
TrunkTrunk TrunkCOTandem TandemCO
signal
signalsignalsignalsignalsignalsignalsignalsignal
signal
035715131 35715131 151315715131
![Page 9: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/9.jpg)
9
Signaling Systems (1/2)
Besides delivering subscriber voice and data information, telecommunication network requires a signaling system.
Signaling is the communication of control information between the signaling elements via some prescribed protocol. For call setup control, administration, disconnect
of the circuit
![Page 10: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/10.jpg)
10
Signaling Systems (2/2)
Two types of signaling functions: Supervisory signals – initiate a call request,
to hold or release an established connection Supervising signals: recognize if subscriber
lines/interoffice trunks are busy or idle Call progress signals: provide call status
information Alerting signals: provide warning to a
subscriber
Address signals
![Page 11: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/11.jpg)
11
Customer-Line Signaling
![Page 12: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/12.jpg)
12
Dial Pulse vs. Dual Tone Multi-Frequency
1
74
*
6A
9 C#
B3
0
52
8D
1209 1336 1477 1633 697
770
852
941
![Page 13: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/13.jpg)
13
Interoffice Trunk Signaling
Control information exchange among the switches is achieved by interoffice trunk signaling.
Two approaches: Channel associated signaling (CAS)
Signaling and voice share the same inbandchannel.
Common channel signaling (CCS) A separate out-of-band signaling network to carry
signaling message.
![Page 14: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/14.jpg)
14
CAS v.s. CCS
Channel Associated Signaling Signaling and voice share
the same channel
Common Channel Signaling Separation of signaling
and call paths Signaling System 7 (SS7)
![Page 15: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/15.jpg)
15
The Advantages of CCS
Signaling packets can be efficiently delivered using signaling links, which reduces the call setup time.
Since the ineffective call attempts are released by the signaling links, better utilization of voice trunks can be expected.
Signaling can be performed during conversation.
![Page 16: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/16.jpg)
16
The first CCS system is signaling system number 6 developed in the 1970s.
The modern CCS system is SS7. SS7 is the foundation for Intelligent Network
(IN) services. SS7 is a dedicated data communication
network and similar to the packet network. SS7 follows OSI 7 layer architecture. Message-based signaling protocol
Signaling System No. 7 (1/2)
![Page 17: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/17.jpg)
17
Signaling System No. 7 (2/2)
To enable a wide range of services to be provided to the end-user
Caller ID, toll-free calling, call screening, number portability, etc.
Signaling between a PCS network and the PSTN are typically achieved by the SS7 network.
![Page 18: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/18.jpg)
Components and Links of SS7
![Page 19: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/19.jpg)
19
Signaling Point (SP)
Each node in an SS7 network is an signal point (SP).
The signaling address of the SP is known as a signaling point code.
Linkset Group of signaling links directly connecting two
adjacent SPs For capability and security reasons
SP SP SP SP
signaling link linkset
![Page 20: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/20.jpg)
20
Basic Components
SSP/Service Switching Point switching, service invocation
STP/Signal Transfer Point signal routing
SCP/Service Control Point service logic execution
IP/Intelligent Peripheral resources such as customized voice
announcement, voice recognition, DTMF digit collection
SSP
SCP
STPIP
SSP
STP
Voice
![Page 21: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/21.jpg)
21
Service Switching Point (SSP)
Trunks connects SSPs to carry user data/voice information.
Signaling links connect SCPs to STPs, and STPs to SSPs.
SSP
SCP
STPIP
SSP
STP
Voice
![Page 22: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/22.jpg)
22
Signal Transfer Point (STP)
To transfer messages from one SPC to another
SSP
SCP
STPIP
SSP
STP
Voice
![Page 23: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/23.jpg)
23
Service Control Point (SCP)
A network entity that contains additional logic and that can be used to offer advanced services
The switch sends a message to the SCP asking for instructions. The SCP, based upon data and service logic that is
available, will tell the switch which actions need to be taken.
An good example – toll-free 080 number
![Page 24: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/24.jpg)
24
Typical SS7 Network Arrangement
A typical SS7 network arrangement. Two switches do not communicate signaling
to each other via direct paths. The quad arrangement ensures great
robustness.
SwitchSwitch
STPSTP
STPSTP
SCP SCP
![Page 25: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/25.jpg)
25
Class 5 End Office Switch
The Telephone Network
Circuit Switched Network
Intelligent Peripheral
Signal Transfer Point
Service Control Point
Class 4 Tandem Switch
Transport Layer
Control Layer
SS7 SignalingISUP MessagesINAP/TCAP Messages
![Page 26: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/26.jpg)
26
Types of Signaling Links in SS7
SSP SSP
F-link
STP
SCP
E-linksA-links
C-link
A-links
A-links
D-link B-link
Another carrier’s SS7 network
One SS7 network
SSP
STP STP
A-links
F-link F-linkSSP
F-link
A-link: Access linkB-link: Bridge linkC-link: Cross linkD-link: Diagonal linkE-link: Extended linkF-link: Full associated link
![Page 27: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/27.jpg)
SS7 Protocol Stack
![Page 28: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/28.jpg)
28
The SS7 Signaling Protocol
OMAP MAP
TCAP
ISDN-UP
SCCP
MTP Level 3
MTP Level 2
MTP Level 1
OSI Layers
Application
PresentationSessionTransport
Network
Data Link
Physical
The SS7 Layers
![Page 29: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/29.jpg)
29
Message Transfer Part (1/2)
MTP Level 1 Defines the physical, electrical and functional
characteristics of the signaling. 100111010110000011100111001.....
MTP Level 2 Dealing with the transfer of messages on a given
link from one node to another Provides reliable transfer of signaling messages
between two directly connected signaling points Error detection and correction, flow control, signal
unit delimitation, etc.
MTP2 MTP3 ISUP
![Page 30: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/30.jpg)
30
Message Transfer Part (2/2)
MTP Level 3 Provides the functions and procedures related to
message routing and network management.
Signaling message handling Providing message routing between signaling
points in the SS7 network
Signaling network management Rerouting traffic to other SS7 signaling links in
the case of link failure, congestion or node failure Load-sharing
![Page 31: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/31.jpg)
31
ISUP
ISDN User Part Used as the protocol for setting up and
tearing down phone calls between switches Initial Address Message (IAM)
To initiate a call between two switches
Answer Message (ANM) To indicate that a call has been accepted by the
called party
Release Message (REL) To initiate call disconnection
![Page 32: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/32.jpg)
32
SCCP
Signaling Connection Control Part Used as the transport layer for TCAP-based
services Both connection-oriented and
connectionless Mostly connectionless signaling
Global title translation (GTT) capabilities The destination signaling point and subsystem
number is determined from the global title
![Page 33: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/33.jpg)
33
TCAP
TCAP (Transaction Capabilities Applications Part)
Supporting the exchange of non-circuit related information between signaling points
Queries and responses sent between SSPs and SCPs are carried in TCAP messages
Freephone (800/888), calling card, wireless roaming
![Page 34: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/34.jpg)
34
MAP and OMAP
Operations, Maintenance, and Administration Part (OMAP)
Mobile Application Part (MAP) Application of TCAP IS-41 & GSM MAP are implemented in MAP layer.
![Page 35: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/35.jpg)
SS7 Messages
![Page 36: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/36.jpg)
36
MTP2 Messages
BSNFlag LI CRCSquare
8 7 1 7 1 6 2 16 8 (bits)
(a) Fill-in Signal Unit (FISU)First bit transmitted
BIB
FSNFIB
BSNFlag LI CRCSquare
8 7 1 7 1 6 2 8 or 16 16 8 (bits)
(b) Link Status Signal Unit (LSSI)First bit transmitted
BIB
FSNFIB
BSNFlag LI CRCSquare
8 7 1 7 1 6 2 8 8n (2n272) 16 8 (bits)
(c) Message Signal Unit (MSU)First bit transmitted
BIB
FSNFIB
Status
SIO SIF
Flag
Flag
Flag
![Page 37: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/37.jpg)
37
ITU-T Message Signal Unit
BSN: Backward Sequence Number BIB: Backward Indicator Bit FSN: Forward Sequence Number FIB: Forward Indicator Bit LI: Length Indicator SIO: Service Indicator Octet
SI: Service Indicator NI: Network Indicator RL: Routing Label DPC: Destination Point Code OPC: Originating Point Code SLS: Signaling Link Selection SIF: Signaling Information Field
01111110 BSN FSN LI SIO RL SIF CRC
MTP Upper LayerLevel 3Level 2
BIB
FIB
MTP
Level 2
NISI4 4
OPCDPC14 14 4
SLS SCCP User Data
/
8 (Flag) 7 1 7 1 6 2 8 32 16 8 (bit)
Example: SCCP message
First bit transmitted
Flag
![Page 38: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/38.jpg)
38
Message Signal Unit (MSU)
DPC = Destination Point Code OPC = Origination Point Code SIO = Service Information Octet SI = Service Indicator NI = Network Indicator SLS = Signaling Link Selection
DPCMemberSIO SLS Message contentDPC
NetworkDPC
ClusterOPC
MemberOPC
NetworkOPC
Cluster
8 8 8 8 8 8 8 8 variable length (bits)
DPCSIO SLS Message contentOPC
8 14 14 4 variable length (bits)
(a) ANSI MSU
(b) ITU MSU
First bit transmitted
First bit transmitted
SI NI4 4
SPSP
International Signaling gateways
SP
International Signaling plane
National Signaling plane 1National Signaling plane 2
![Page 39: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/39.jpg)
39
ISUP Message Format
DPCSIO SLSOPC
8 14 14 4 12 4 8 (bits)
DPCSIO SLS CICOPC
8 24 24 8 14 2 8 (bits)
(a) ANSI MSU
(a) ITU MSUFirst bit transmitted
/ Message content(variable length)
MessageType
CIC / Message content(variable length)
MessageType
First bit transmitted
DPC = Destination Point Code OPC = Origination Point Code SIO = Service Information Octet SLS = Signaling Link Selection CIC = Circuit ID Code
![Page 40: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/40.jpg)
40
ISUP Message
ISUP messages Establishes circuit-switched network connections Call setup/release between the PSTN and a PCN.
ISUP messages that are delivered by MTP routing.
![Page 41: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/41.jpg)
41
ISUP Messages (1/2)
IAM (Initial Address Message) called number, calling number, transmission
requirement, type of caller, other information
ACM (Address Complete Message) One-way path from destination to calling switch Note: Called switch generates the ring-back tone.
ANM (Answer Message)
![Page 42: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/42.jpg)
42
ISUP Messages (2/2)
REL (Release) Message To release the call
RLC (Release Complete) Message Complete the call
![Page 43: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/43.jpg)
43
Basic Call Setup
Phone A Phone BSwitch 1 Switch 2
Off Hook
Dial Tone
Dial Digits (Setup) IAM (Setup)
ACM (Alert)
Ring Tone (Alert)Ringback Tone (Alert)Call Path Establishment
Off Hook (Connect)ANM (Connect)
Conversation
(Setup) PagingInitial Dial Tone (Page Response)
RAB Assignment
Connect Ack
Dial Tone Off (Preceeding)
Ringback Tone Off (Connect)
RAB Assignment
Ringback Tone Off (Connect Ack)
![Page 44: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/44.jpg)
44
Basic Call Release
Phone A Phone BSwitch 1 Switch 2
Conversation
On Hook (Disconnect)
REL
RLC
Call Path Release
Call Path ReleaseRelease
Disconnect
Release
![Page 45: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/45.jpg)
45
MTP Layer Routing (1/2)
Signaling Connection
COCO
Off Hook
RingingIAM(CIC=5, Called Number=5715131)
Dial Tone5715131
Subscrber LineCIC 1
CIC 50
ACM(CIC=5, ....)ANM(CIC=5, ....)
ConversationREL(CIC=5, ...)RLC(CIC=5, ....)
IAM: Initial Address Message ACM: Address Complete Message ANM: Answer Message
REL: Release Message RLC: Release Complete Message
On Hook
On Hook
![Page 46: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/46.jpg)
46
MTP Layer Routing (2/2)
Destination Point Code (DPC) = actual address of the destination node.
Lookup tables is used in the MTP Routing based on DPC
SSP
STP
SSPSpeech circuit 13100
110
200
CIC DPCOPC13 200100
DPC Link Set200
:11,12
:
Routing Table
11
12
STP
DPC Link Set200
:31,32
:
STP
STP3132
DPC Link Set200
:61:
6162
2625
27
![Page 47: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/47.jpg)
47
SCCP Layer Routing
Global Title Translation (GTT) is a function defined within SCCP. Performed at a STP or MSC.
GTT is the process of translating a network layer address, dialed digits, or a service subsystem number (SSN), to the point codeof the destination SSP.
Routing based on GT translations Called Party Address (PC+SSN+GT) Calling Party Address (PC+SSN+GT)
ASE SSNReserved 0000010
HLR 00000110VLR 00000111MSC 0000100EIR 0000100AuC 0000101
![Page 48: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/48.jpg)
48
SCCP Message Embedded TCAP Message
01111110 01111110BSNFSNLISIORLSIFCK
SCCP
Level 3 Level 2
8 (Flag) 16 32 8 2 6 1 7 1 7 8 (Flag) bit
First bit transmitted
BIB
FIB
Level 2
SI=0011SSF4 4
DPCOPC4 14 14
SLS
/
Message Type: Unitdata ‘00001001’ Protocol Class: Class 0 or Class 1
UserData
Calling PartyAddress
Called PartyAddress
ProtocolClass
MessageType
Component Portion
TransactionPortion
SCCP message
TCAP message
![Page 49: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/49.jpg)
49
GTT Example
GT DPC*:
GA:
GTT Table (A)
VLRHLR
STP A
STP C
STP B
GA GB* A
DPC * GADPC
* GBDPC
* GBDPC
* BDPC
*SCP BDPC
*: Global Title of HLR :Perform GTT
GT DPC*:
GB:
GTT Table (GA) GT DPC*:
STP B:
GTT Table (GB)
GT DPC*:
SCP B:
GTT Table (B)
SCP BSCP A SS7
Network ASS7 Network B
International SS7 Network
![Page 50: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/50.jpg)
PCS/PSTN Call Control Using ISUP
![Page 51: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/51.jpg)
51
Land-to-Mobile Call Setup and Release
![Page 52: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/52.jpg)
52
Mobile-To-Land Call Setup and Release
![Page 53: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/53.jpg)
53
Performance Requirements for SS7
A given route set should not be out of service for more than 10 minutes per year.
No more than 1x10-7 messages should be lost.
No more than 1x10-10 messages should be delivered out of sequence.
In ISUP, numerous timing requirements must be met.
![Page 54: Ch5- SS7 [相容模式]](https://reader030.fdocuments.us/reader030/viewer/2022012109/61dc58b981b3a6048f38f7b0/html5/thumbnails/54.jpg)
54
Summary
SS7: out-of-band signaling method Components and Links of SS7
3 components: STP, SSP and SCP 6 links: A-F links.
PCN/PSTN Call Control Using ISUP Land-to-Mobile Call Setup/Release Procedures Mobile-to-Land Call Setup/Release Procedures