Engineering TechnologyCerritos Collegewww.cerritos.edu/et

THREE CERTIFICATES OF ACHIEVEMENT ARE AVAILABLE • ELECTRICAL AND ELECTRONIC ENGINEERING TECHNICIAN • MECHANICAL ENGINEERING TECHNICIAN • INDUSTRIAL ENGINEERING TECHNICIAN

AA DEGREE IS ALSO AVAILABLE

ELECTRICAL AND ELECTRONIC ENGINEERING TECHNICIAN CERTIFICATE OF ACHIEVEMENT • ET 101 Principles of Engineering Technology (3 Units).............................................................................Completed • ET 102 Electronics for Engineering Technologists (3 Units) .....................................................................Completed • ENGT 103 Introduction to Engineering Design Using Inventor (3 Units) .....................................................Completed • ENGT 131 Design Fundamentals Including Solid Modeling (3 Units) ...........................................................Completed • ENGT 299 Directed Studies (2 Units) ................................................................................................................Completed

- or NPD 105 Mechatronics Integration In New Product Development (3 Units).....................................Completed

Total Certificate Requirement: 14-15 Units

MECHANICAL ENGINEERING DESIGN TECHNICIAN CERTIFICATE OF ACHIEVEMENT • ET 101 Principles of Engineering Technology (3 Units).............................................................................Completed • ENGT 103 Introduction to Engineering Design Using Inventor (3 Units) .....................................................Completed • MTT 180 Robotics for Computer Numerically Controlled Machines (3 Units) ..........................................Completed

Plus one course from the following: • ET 102 Electronics for Engineering Technologists (3 Units) .....................................................................Completed • ENGT 104 Principles of Aerospace Design Technology (4 Units) ..................................................................Completed • ENGT 131 Design Fundamentals Including Solid Modeling (3 Units) ...........................................................Completed • MTT 51 Mastercam Milling (3.5 Units) .........................................................................................................Completed • WELD 120 Beginning Arc Welding (5 Units) ......................................................................................................Completed

Total Certificate Requirement: 12-14 Units

INDUSTRIAL ENGINEERING DESIGN TECHNICIAN CERTIFICATE OF ACHIEVEMENT • The Engineering Technology Basic Core Classes (9 units)

- ET 93L Process Control Laboratory (1 unit) ...............................................................................................Completed - ET 101 Principles of Engineering Technology (3 units) .............................................................................Completed - ET 102 Electronics for Engineering Technologists (3 units)......................................................................Completed - ET 103 Industrial Process Control (2 units) ...............................................................................................Completed

• ET 91L Engineering Technology Project Laboratory (1 unit)....................................................................Completed • ET 104 Engineering Technology Project Development (1 unit) ..............................................................Completed • ET 105 Industrial Motor Control (2 units) ..................................................................................................Completed • NPD 104 Programmable Logic Controllers in New Product Development (3 units) ...............................Completed • NPD 106 Safety in New Product Development (2 units) .............................................................................Completed

Total Certificate Requirement: 18 Units

For more information on Certificates, please refer to the current General Catalog: www.cerritos.edu/catalog

Engineering TechnologyCerritos Collegewww.cerritos.edu/et

New Students and/or 1st Semester Students can take the recommended classes:

• ET 101 (3 units) Principles of Engineering Technology • ET 102 (3 units) Electronics for Engineering

Technologists • ET 103 (2 units)  Industrial Process Control • ET 105 (2 units) Industrial Motor Control • ENGT 103 (3 units) Introduction to Engineering Design

Using Inventor • MTT 100 (2 units) Machine Tool Introduction • MTT 180 (3 units) Robotics for Computer Numerically

Controlled Machines • NPD 104 (3 units) Programmable Logic Controllers in New

Product Development • NPD 106 (2 units) Safety in New Product Development • PMT 50 (1.5 units) Survey of Hydraulics and Pneumatics • PMT 100 (2.5 units) Plastics Technology • WELD 100 (2.5 units) Welding Fundamentals • WMT 101 (3 units) Introduction to Woodworking

2nd Semester Students and/or Continuing Students may take any of the following classes in conjunction with the 1st Semester recommended classes and/or in later pursuit of certificate:

• ET 91L (1 unit) Engineering Technology Project Laboratory

• ET 93L (1 unit) Process Control Laboratory • ET 104 (1 unit) Engineering Technology Project

Development

For detailed course descriptions, please refer to the current General Catalog: www.cerritos.edu/catalog

Interested in enrolling at Cerritos College? Please refer to the step-by-step enrollment process: www.cerritos.edu/futurestudents

Want to apply to get your certificate? 1. Make sure you meet the requirements for the Certificate

Determine which form to fill out and download the form at: www.cerritos.edu/admissions-and-records - Petition for Certificate: Petition to graduate with a

Certificate of Achievement

2. Fill out the appropriate form and meet with a counselor - Make an appointment by calling (562) 860-2451,

ext. 2231 or use Online Counseling at: www.cerritos.edu/counseling/online-orientation.htm.

11110 Alondra Blvd., Norwalk, CA 90650

www.cerritos.edu/et

11/2019