Centrifuge Labware
Transcript of Centrifuge Labware
Centrifuge Labware Tubes – Bottles – Adapters
2014-02
page 2 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Contents 1. Selection Guide Page 3
1.1. Volume Page 3 1.2. Chemical Resistance Page 3 1.3. Thermal Resistance Page 3 1.4. Transparency Page 3
2. Material Description Page 4 2.1. Materials for Tubes and Sealing Caps Page 4 2.2. Sterilization Page 5 2.3. Chemical Resistance Page 6 2.4. Nomograph Relative Centrifugal Force Page 8
3. Ordering Information and Prices Page 9 3.1. Glass Tubes Page 9 3.2. Plastic Tubes Page 12 3.3. Advanced Oak Ridge Tubes Page 16 3.4. Bottles Page 20 3.5. Tubes and Bottle for Ultra Centrifuges Page 25 3.6. Other Accessories Page 28
4. Compatibility with Rotors of other Manufacturers Page 29
5. Price List (sorted by Catalog No.) Page 30
Many factors influence the performance characteristics and lifespan of centrifuge consumables. This catalog has been compiled as a general guideline but, in no case, expresses absolute guarantee of the products under laboratory conditions. Due to the large number of different applications and techniques the single „perfect“ material for centrifuge tubes does not exist. A material may show excellent performance qualities in one application and then fail horribly in the next.
Note: All centrifuge tubes should be tested prior to use. At the first sign of irregularities these tubes
should be discarded or the maximum speed should be lowered drastically.
List of used trademarks: AOR – Advanced Oak Ridge Tubes (Utility patent of Herolab GmbH Laborgeraete) Borex and Polyflor are registered trademarks of Herolab GmbH Laborgeraete, Wiesloch, Germany. Delrin – is a registered trademark of DuPont, Delaware, U.S. Duran – is a registered trademark of Schott, Mainz, Germany.
page 3 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
1.1. Volume
The volume of the tubes is determined by the size of the sample material, the rotor bores and the necessary adapters.
1.2. Chemical Resistance
Chemical Groups B, D PA PPCO PP PE PC PF PS
Acids, dilute S S S S S S S S
Acids, strong S S S S S U S M
Alcohols and bases S S S S S U S S
Aldehydes and oxidizing agents S M M M M M S U
Esters S M M M M U S U
Hydrocarbons Aliphatic (i.e. hexane)
S M M S U U S U
Hydrocarbons halogenated or aromatic (i.e. phenol, chloroform)
S M M M M U S U
Ketones (i.e. acetone) S M M M M U S U
Salts S S S S S M S M
1.3. Thermal Resistance
Temperature Range B, D PA PPCO PP PE PC PF PS
< +4°C U S S U S S S U
+4°C to +20°C S S S M S S S S
+20°C to +40°C S M S S S S S S
Autoclavable S S S S U S S U
Note: For continuous low temperature applications PPCO resp. PA is the material of choice.
1.4. Transparency
Transparency Range B, D PA PPCO PP PE PC PF PS
Transparent x x x
Translucent x x x x
Opaque x
S Satisfactory B Borex® Glass PPCO Polypropylene Copolymer PC Polycarbonate
M Marginal, test runs recommended D Duran® Glass PP Polypropylene PF Polyflor
®
U Unsuitable, not recommended PA Polyallomer PE Polyethylene PS Polystyrene
1.
Selection Guide
page 4 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
2.1. Materials for Tubes and Sealing Caps Tubes and capping systems can only function at optimal performance levels if the rotor and centrifuge are kept in the best possible condition. The condition of your rotors is critical to ensure the correct functioning of the tube and capping system. Follow the instructions in your rotor manual and clean your rotors carefully after each run to prevent the start of corrosion and rotor degradation.
Glass Borex = B / Duran = D / HS = High-Speed Temperature range: B = 0 to + 250°C / D = 0 to + 200°C / HS = 0 to + 300°C
Transparent glass tubes are available in Borex and Duran for low speed applications when clarity and good chemical tolerance is required. Glass tubes must be treated with care when removing pellets, washing and storing. Surface scratches and etchings will significantly reduce the life span of glass tubes. All glass tubes show a better tolerance to high temperatures than to low temperatures. However, strong acids and bases may attack the glass surface at elevated temperatures. Hydrofluoric acid attacks glass already at room temperature. High-Speed glass can be spun at higher g-forces than the other two glass materials.
Polyallomer PA or Polypropylene Copolymer PPCO Temperature range: - 40° to + 125°C
Polyallomer is a copolymer of polypropylene and polyethylene resulting in a material with the best features of each component. It is a translucent material which attains additional "contact" clarity when filled with liquid allowing easy viewing of pellets, liquid levels and interfaces. PA is the most versatile of all tube materials and is the best choice if uncertain about the particular effects of an application on a polymer.
Polyallomer is the material of choice for continuous low temperature centrifugation applications.
Polypropylene PP Temperature range: - 180° to + 145°C
Polypropylene is a translucent material with good chemical and temperature resistance.
It may become brittle when exposed to low temperatures; therefore, centrifugation at temperatures below 4°C should be avoided. It is important to equilibrate cold tubes to the temperature of the run before centrifuging, particularly if experimental protocols call for repeated spins and temperature adjustments. Polypropylene is only translucent, but liquid levels, sharp interfaces and pellets can be easily viewed.
Polyethylene PE Temperature range: - 180° to + 90°C
Polyethylene is the material of choice for techniques involving acetone, acetic or hydrochloric acid. It is an opaque polymer which makes the viewing of tube contents slightly difficult; however its increased flexibility, compared to other polymers, makes it an excellent tube for slicing, piercing or low temperature applications. Polyethylene tubes need to be completely filled and capped to run at maximum speeds. Polyethylene is sensitive to high temperatures and cannot be autoclaved.
2.
Material Description
page 5 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Polycarbonate PC Temperature range: - 150° to + 121°C
Polycarbonate is a transparent, rigid and non-pierceable material. It is compatible with neutral salt and dilute acid solutions but extremely sensitive to organic solvents, alcohols, oils, DMSO and alkaline solutions. Tubes and bottles are reusable, but care should be taken to avoid scratching the surface with glass rods and hard bristle brushes. Please use rubber coated spatulas and soft bristle brushes. – Important note for cleaning: Use only mild, non-alkaline detergents and wash them by hand. Repeated washing in machines or the use of alkaline detergents will damage the material.
Polyflor PF Temperature range: - 100° to + 140°C
Polyflor is a translucent material with excellent chemical resistance to acids, bases, salts and organic solvents at temperatures encountered during centrifugation. Some organic solvents will attack the fluorocarbon but only at elevated temperatures above 50°C. This Teflon-like polymer has excellent temperature resistance and is a good choice for low temperature applications. The material is slightly flexible and tubes need to be completely filled and capped to run at the maximum listed speeds.
Polystyrene PS Temperature range: - 10° to + 75°C
Polystyrene is a transparent rigid material compatible with most aqueous based solutions but not with most organic solvents. This material has limited temperature resistance and cannot be autoclaved. Tubes will break if dropped or subjected to high stress conditions (temperature extremes or high g-forces). All polystyrene tubes are thickwall and should be used only once, then discarded. The primary uses of polystyrene tubes are low speed applications, i.e. pelleting, when clarity is essential.
2.2. Sterilization
Sterilization B, D, HS PA PPCO PP PE PC PF PS
Autoclave x x x x x x
Dry Heat x x
Gas x x x x x x x x
Chemical x x x x x x x x
UV Light x x x
Tubes or bottles made of PA, PC, PF, PPCO and PP can be autoclaved repeatedly under the normal condition of at least 15 minutes at 121°C and 103 kPa (1,03 bar = 15 psi). The sterilization time for PC should not exceed 20 minutes at 121°C, as repeated sterilization reduces the mechanical rigidity of PC but also of all other plastic materials as well. Pathogenic prions (Creutzfeld-Jakob disease, (vCJD)) can be destroyed only through sterilization at 134°C with duration of 18 minutes. For this application we, Herolab, can offer a special polypropylene (PPCO) on request.
General guidelines for autoclaving:
All products must be thoroughly rinsed with distilled water before being autoclaved, since residues of cleansing agents can cause cracks, discolorations and stains.
Closures of tubes or bottles need to be removed completely before autoclaving in order to prevent damages during the cooling-down process.
Tubes and bottles that had been autoclaved previously must be checked for signs of deformation or cracks before using them again.
2.
Material Description
page 6 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
2.3. Chemical Resistance
PA PPCO
PC PE PF PP PS PA PPCO
PC PE PF PP PS
acetaldehyde M U M M M U deoxycholate S S S - S -
acetic acid (5%) S S S S S1 U dextran (dextran sulfate) S S S S S -
acetic acid (60%) S U S S M S diacetone S - S S S M
acetic acid (glacial) S U M S U U diethylether M U U S M U
acetone S U S M S U diethyl ketone U U M - M U
Alconox® S M S - S - diethylpyrocarbonate S U S - S U
allyl alcohol S S S - S M N,N-dimethylformamide S U S U S U
aluminium chloride S S S S S M dimethylsulfoxide S U U - S U
aluminium fluoride S U S S S M dioxane M U S M M S
ammonia S U U S S S ethanol (5%) S U S S S S
ammonium acetate S S S - S S ethanol (50%) S U S S S S
ammonium carbonate S U S S S - ethanol (70%) S U S S S S
ammonium hydroxide (10%) S1 U S S S
1 S ethanol (95%) S U M S S U
ammonium hydroxide (28%) S1 U S S S
1 M ethyl acetate M U U S U U
ammonium hydroxide (cone.) S1 U S S S
1 M ethylene dichloride U U U S U U
ammonium phosphate S S S S S - ethylene glycol S U S S S S
ammonium sulfate S S S S S - ethylene oxide S M S S S U
ammonium sulphide S U - S S S ethylene M U U - M -
amyl alcohol M S S S M S fatty acids, saturated S S U S S S
aniline (benzenamine) U U U S M U fatty acids, unsaturated S S U S S S
Aqua Regia U U U - U M ferric chloride S — S S — —
barium salts S S S S S - Ficoll-Paque S S S - S -
benzene U U U S U U fluoroboric acid S - S - S -
benzyl alcohol U U U S U U formaldehyde (5%) S S S S S S
boric acid S S S S S S formaldehyde (40%) S S S S S S
n-butyl alcohol S M M S S S formic acid (3%) S U S - S S
calcium chloride S M S S S1 - formic acid (10%) S U S - S S
calcium hydrochloride S M S S S M gallic acid S - S S S -
carbon tetrachloride U U U - U U glycerol S S S S S S
cesium acetate S S S - S - guanidine hydrochloride S U S - S -
cesium bromide S S S S S - guanidine isothiocyanate S U - - - -
cesium chloride S S S S S - Haemo-Sol S S S - S -
cesium formate S S S - S - 2-heptyl S - S S S -
cesium iodide S S S - S - hexane M U U S S U
cesium sulfate S S S S S - hydrochloric acid (5%) S S S S S S
cesium trifluoracetate S S S - S - hydrochloric acid (10%) S U S S S S
chlorine water S S M S S M hydrochloric acid (37%) M U S S M S
chlorobenzene U U U S U U hydrochloric acid (50%) M U S S M S
chloroform M U M S M U hydrochloric acid (cone.) M U - S S S
chromic acid (10%) S M U S S M hydrofluoric acid (10%) S M S S S S
chromic acid (50%) S1 U U S S M hydrofluoric acid (50%) S U S S S S
citric acid (10%) S S S S S S hydrofluoric acid (100%) S U S S S -
cresol M U U - U M hydroformic acid (100%) S - S - S -
cyclohexane U U U S U U hydrogen peroxide (3%) S S S1 S S S
cyclohexanol S M S S S S hydrogen peroxide (100%) S S S1 S S M
2.
Material Description
Note: This chart has been consolidated from a number of sources. Chemical resistance data is included only as a guide to the select ion of tube materials.
No organized chemical resistance data exist for materials under the stress of centrifugation. The recommendation is to test sample lots prior to use.
2.
Material Description
page 7 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
PA PPCO
PC PE PF PP PS PA PPCO
PC PE PF PP PS
isbutanol S S S - S M potassium hydroxide (45%) S U S S U M
isopropanol S U S - S M potassium hydroxide (cone.) S U S S U M
kerosene U U U S U U potassium permanganate S S S S S -
lactic acid (20%) S S M S S S 2-propanol S U S S S S
lactic acid (50%) S S M S S S pyridine (50%) M U U M S U
lactic acid (100%) S S M S S S rubidium bromide S S S - S -
lauryl alcohol S - S - S - rubidium chloride S S S - S -
lead acetate S - S S S - silver cyanide S - S S S -
magnesium chloride S S S S S - silver nitrate S S S S S M
magnesium hydroxide S U S S S - sodium bisulphate S S S S S -
maleic acid S — S S S — sodium borate S S S - S -
manganese salts S - S - S - sodium bromide S S S S S -
mercaptoacetic acid S U U - U - sodium carbonate S U S S S -
2-mercaptoethanol S U - - S - sodium chloride (10%) S S S S S S
methanol S U S S S1 S sodium chloride, saturated S S S S S -
methyl ethyl ketone S U U M S U sodium dichromate S - S - S -
methylene chloride U U U S U U sodium dodecyl sulfate S S S S S -
metrizamide S S S - S - sodium hydroxide (1%) S U S - S S
nickel salts S S S S S - sodium hydroxide (10%) S U S - S S
nitric acid (10%) S1 S S S S S sodium hydroxide (cone.) M U S - M S
nitric acid (30%) S1 M U S M S sodium hypochlorite S
1 S U S U -
nitric acid (50%) S1 M U S M M sodium iodide S S S - S -
nitric acid (95%) M U U S M M sodium nitrate S U S S S -
oils (petroleum) S U U S U S sodium peroxide S - S S S -
oils (other) S U U S S S sodium sulfate S S S S S -
oleic acid S S S - S - sodium sulfite S S S S S -
oxalic acid S U S S S - sodium sulphide S U S S S -
perchloric acid (10%) S U M S M M sodium thiosulphate S S S S S -
perchloric acid (70%) M U M S M M Solution 555 (20%) S S S - S -
phenol (5%) S U M S S M sucrose S S S S S S
phenol (50%) M U M S M M sucrose, alkaline S U S - S S
phenylethyl alcohol S - S - S - sulfuric acid (10%) S S M S S S
phosphoric acid (10%) S S S S S S sulfuric acid (50%) S U M S S S
phosphoric acid (30%) S S S S S S sulfuric acid (cone.) S1 U S S S
1 -
phosphoric acid (85%) S S S S S S tannic acid S - S - S -
phosphoric acid (cone.) M U S S M - tetrahydrofuran U U U M U U
phosphorus trichloride S U S S S - toluene U U U S U U
physiologic fluids S S S S S - trichloracetic acid S M U - S U
picric acid S S S S S S trichlorethane U U S S U M
potassium acetate S M S - S - trisodium phosphate S - S S S -
potassium bromide S S S S S - Triton X-100 S S S - S -
potassium carbonate S U S S S - turpentine M U U - M U
potassium chlorate S S S S S - urea S S S S S S
potassium chloride S S S S S - water S S S S S S
potassium hydroxide (5%) S U S S S S xylene U U U S U U
Zephiran chloride (1%) S S S - S -
zinc chloride S S S S S -
zinc sulfate S S S S S -
S Satisfactory S1 Discolored M Marginal resistance – We recommend test runs under appropriate conditions (speed and duration) U Unsatisfactory, not recommended - Performance unknown, tests recommended
page 8 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
2.4. Nomograph – Relative Centrifugal Force
2.
Material Description
page 9 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.1.1. Ordering Information
Available Adapters for rotors with the following bores
14 ml 16 ml 50 ml 250 ml
Nominal Volume
Dimensions (mm) Ø x Length
Material and Form
Cat. No. Tube
Cat. No. Cap
Cat. No. /Places
Cat. No. /Places
Cat. No. /Places
Cat. No. /Places
3 ml 5 ml
10 x 75 12 x 75
D -R B B -R B
25 10 10 25 10 20
25 56 40 / 1
25 55 80 / 1
25 55 10 / 2
25 50 90 /15
25 51 00 / 9
10 ml 10 ml 12 ml 15 ml 15 ml
13 x 100 18 x 102 18 x 102 18 x 102 17 x 98
D -R B D -C B/G B -R B HS -R B D -R B
25 10 40 25 10 60 25 11 00 25 10 91 25 12 80
25 46 50 25 46 50
25 56 00 / 1
25 58 20 / *
25 58 20 / *
25 55 30 / 1
25 55 40 / 1
25 55 50 / 1
25 55 50 / 1
25 51 10 / 9
25 51 30 / 5
25 51 30 / 5
30 ml 30 ml 45 ml
24 x 105 24 x 105 28 x 102
B -R B HS -R B B -R B
25 11 10 25 11 41 25 12 60
25 55 60 / 1
25 55 60 / 1
25 58 00 / *
25 51 60 / 3
25 51 60 / 3
200 ml 60 x 115 D -R B only for
swing-out rotors 25 12 70 25 58 10 / *
* Bottom Support Pad
B Borex® Glass CB Conical bottom FL Flange / Rim
D Duran® Glass RB Round bottom G Graduated
HS High Speed Glass
3.1. Glass Tubes
page 10 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.1.2. Additional Information and Prices
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Tested
up to ... rpm
Tested
up to ... x g
Units
per pack
25 10 10 3 ml 3.2 ml D -R B 5,000 3,000 10
25 10 20 5 ml 4.8 ml B -R B 5,000 *6,000 10
25 10 40 10 ml 8.0 ml D -R B 5,000 3,000 10
25 10 60 10 ml 8.4 ml D -C /G 10,000 *10,000 10
25 10 91 15 ml 15.0 ml HS -R B 9,000 *12,500 6
25 11 00 12 ml 11.4 ml B -R B 7,000 *12,500 10
25 11 10 30 ml 25.0 ml B -R B 5,000 *12,500 10
25 11 41 30 ml 30.0 ml HS -R B 10,000 *12,500 6
25 12 60 45 ml 31.5 ml B -R B 5,000 8,000 10
25 12 70 200 ml 162.5 ml D -R B 4,000 for swing-out rotors only 2
25 12 80 15 ml 12.0 ml D -R B 5,000 3,000 10
* Speed in rpm in swing-out rotors
3.1.3. Closures for Glass Tubes
Cat. No. Description Fits for: Units
per pack
25 46 50 Rubber cap for glass tubes 25 10 60 25 11 00
10
B Borex® Glass CB Conical bottom FL Flange / Rim
D Duran® Glass RB Round bottom G Graduated
HS High Speed Glass
Attention: Kindly note packaging sizes for your orders.
3.1. Glass Tubes
page 11 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.1.4. Adapters/Bottom Support Pads for Glass Tubes
Cat. No. Description Material Number
of places
For rotor bores
Units
per pack
25 50 90 Adapter Plastic 15 250 ml 2
25 51 00 Adapter Plastic 9 250 ml 2
25 51 10 Adapter Plastic 9 250 ml 2
25 51 30 Adapter Plastic 5 250 ml 2
25 51 60 Adapter Plastic 3 250 ml 2
25 55 10 Adapter Rubber 2 50 ml 2
25 55 30 Adapter Rubber 1 50 ml 2
25 55 40 Adapter Rubber 1 50 ml 2
25 55 50 Adapter Rubber 1 50 ml 2
25 55 60 Adapter Rubber 1 50 ml 2
25 55 80 Adapter Rubber 1 16 ml 4
25 56 00 Adapter Rubber 1 16 ml 4
25 56 40 Adapter Rubber 1 14 ml 4
25 58 00 Bottom Support Pad Rubber 50 ml 4
25 58 10 Bottom Support Pad Rubber 250 ml 4
25 58 20 Bottom Support Pad Rubber 16 ml 4
Attention: Kindly note packaging sizes for your orders.
3.1. Glass Tubes
page 12 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.2.1. Ordering Information Available Adapters for rotors with
the following bores 14 ml 16 ml 50 ml 250 ml
Nominal Volume
Dimensions (mm) Ø x Length
Material and Form
Cat. No. Tube
Cat. No. Cap
Cat. No. /Places
Cat. No. /Places
Cat. No. /Places
Cat. No. /Places
1.0 ml 1.5 ml 4.5 ml 5.0 ml
7 x 50 11 x 40 12 x 75 12 x 75
PS -RB PP -CB -Eppendorf PP -RB PS -RB
25 20 00 25 20 50 25 22 30 25 22 00
included
25 50 71 / 1
25 50 73 / 1
25 50 73 / 1
25 50 70 / 1
25 50 72 / 1
25 50 72 / 1
25 50 00 / 4
25 50 10 / 2
25 50 11 / 2
25 50 11 / 2
25 52 10/15
25 51 00 / 9
25 51 00 / 9
13.0 ml 13.5 ml
17 x 98 16 x 76
PP -RB PP -RB
25 26 10 25 24 70
14 ml 14 ml 14 ml 14 ml 14 ml
18 x 75 18 x 75 18 x 75 18 x 75 18 x 75
PA -R B PC -R B PE -RB PF -R B PP -RB
25 26 90 25 25 70 25 26 60 25 25 90 25 25 80
25 45 50 25 45 50 25 45 51 25 45 50 25 45 50
directly
directly
directly
directly
directly
16 ml 16 ml 16 ml 16 ml
18 x 100 18 x 100 18 x 100 18 x 100
PC -RB/FL PE -RB/FL PF -RB/FL PPCO(PA)-RB/FL
25 27 00 25 27 40 25 27 51 25 27 20
25 45 50 25 45 51 25 45 50 25 45 50
directly
directly
directly
directly
25 50 50 / 1
25 50 50 / 1
25 50 50 / 1
25 50 50 / 1
25 51 30 / 5
25 51 30 / 5
25 51 30 / 5
25 51 30 / 5
50 ml 50 ml 50 ml 50 ml 50 ml 50 ml
29 x 103 29 x 103 29 x 103 29 x 103 29 x 103 29 x 103
PC -RB/FL PC -RB/FL/LC PE -RB/FL PF -RB/FL PPCO(PA)-RB/FL
PPCO(PA)-RB/FL/LC
25 31 00 25 31 05 25 31 30 25 31 51 25 31 60 25 31 45
25 46 00 included 25 46 00 25 46 00 25 46 00 included
directly
directly
directly
directly
directly
directly
70 ml 70 ml 94 ml
35 x 98 35 x 105 38 x 106
PC -RB/G PP -RB PP -RB
25 30 90 25 31 90 25 32 50
100 ml 100 ml 120 ml
40 x 115 45 x 98 40 x 115
PC -RB/G PC -RB/G
PP - R B
25 33 00 25 33 20
25 33 10
25 51 70 / 1
25 51 70 / 1
PA Polyallomer CB Conical bottom FL Flange / Rim
PPCO Polypropylene Copolymer RB Round bottom G Graduated
PP Polypropylene LC Loop cap
PE Polyethylene PF Polyflor®
PC Polycarbonate PS Polystyrene
3.2. Plastic Tubes
page 13 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.2.2. Additional Information and Prices
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Tested
up to ... rpm
Tested
up to ... x g
Units
per pack
25 20 00 1.0 ml 1.0 ml PS-RB (1.000 St.) 5,000 2,500 pack
25 20 50 1.5 ml 1.5 ml PP-CB-Eppendorf ( 1.000 St.) * 16,000 30,000 pack
25 22 00 5.0 ml 4.5 ml PS-RB (1.000 St.) 5,000 2,500 pack
25 22 30 4.5 ml 4.5 ml PP-RB (1.000 St.) 20,000 36,000 pack
25 25 70 14 ml 11.3 ml PC-RB 24,000 59,889 10
25 25 80 14 ml 10.8 ml PP-RB 20,000 41,590 10
25 25 90 14 ml 10.7 ml PF-RB 20,000 41,590 2
25 26 10 13.0 ml 12.5 ml PP-RB 12,000 16,099 10
25 26 60 14 ml 11.5 ml PE-RB 20,000 41,590 10
25 26 90 14 ml 10.8 ml PA-RB 24,000 59,889 10
25 27 00 16 ml 15.5 ml PC-RB/FL 24,000 70,965 10
25 27 20 16 ml 14.5 ml PPCO(PA)-RB/FL 24,000 70,965 10
25 27 40 16 ml 15.0 ml PE-RB/FL 20,000 49,281 10
25 27 51 16 ml 14.5 ml PF-RB/FL 20,000 49,281 2
25 30 90 70 ml 60.0 ml PC-RB/G 8,000 7,155 10
25 31 00 50 ml 42.8 ml PC-RB/FL 24,000 69,549 10
25 31 05 50 ml 42.8 ml PC-RB/FL/LC * 24,000 69,549 10
25 31 30 50 ml 40.9 ml PE-RB/FL 20,000 48,298 10
25 31 45 50 ml 42.1 ml PPCO(PA)-RB/FL/LC * 24,000 69,549 10
25 31 51 50 ml 40.0 ml PF-RB/FL 20,000 48,298 2
25 31 60 50 ml 42.1 ml PPCO(PA)-RB/FL 24,000 69,549 10
25 31 90 70 ml 62.0 ml PP-RB 8,000 7,155 10
25 33 00 100 ml 100.0 ml PC-RB/G 8,000 8,586 2
25 33 10 120 ml 108.0 ml PP-RB 6,000 5,635 10
25 33 20 100 ml 100.0 ml PC-RB/G 8,000 8,586 10
* Cap included
PA Polyallomer CB Conical bottom FL Flange / Rim
PPCO Polypropylene Copolymer RB Round bottom G Graduated
PP Polypropylene LC Loop cap
PE Polyethylene PF Polyflor®
PC Polycarbonate PS Polystyrene
Attention: Kindly note packaging sizes for your orders.
3.2. Plastic Tubes
page 14 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.2.3. Closures for Plastic Tubes
Cat. No. Description Fits for: Units
per pack
25 45 50 Cap for 14 tubes (PA, PC, PF, PP) and for 16 ml tubes (PPCO(PA), PF, PC)
25 26 90 25 25 70 25 25 90 25 25 80
25 27 00 25 27 51 25 27 20
10
25 45 51 Cap for 14 ml + 16 ml tubes (PE) 25 26 60 25 27 40 10
25 46 00 Cap for 50 ml tubes (Loop Cap)
25 31 00 25 31 30 25 31 51 25 31 60
10
Attention: Kindly note packaging sizes for your orders.
3.2. Plastic Tubes
page 15 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.2.4. Adapter for Plastic Tubes
Cat. No. Description Material Number of
places For rotor
bores Units
per pack
25 50 00 Adapter Plastic 4 50 ml 2
25 50 10 Adapter Plastic 2 50 ml 2
25 50 11 Adapter Plastic 2 50 ml 2
25 50 50 Adapter Plastic 1 50 ml 2
25 50 70 Adapter Plastic 1 16 ml 2
25 50 71 Adapter Plastic 1 14 ml 2
25 50 72 Adapter Plastic 1 16 ml 2
25 50 73 Adapter Plastic 1 14 ml 2
25 51 00 Adapter Plastic 9 250 ml 2
25 51 30 Adapter Plastic 5 250 ml 2
25 51 70 Adapter Plastic 1 250 ml 2
25 52 10 Adapter Plastic 15 250 ml 2
Attention: Kindly note packaging sizes for your orders.
3.2. Plastic Tubes
page 16 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.3.1. Ordering Information Available Adapters
for rotor bores
50 ml 94 ml
Nominal Volume
Dimensions (mm)
Ø x Length
Material and Form
Cat. No. Tube
complete
Cat. No. Tube
Cat. No. Cap
Cat. No. O-Rings
(3 units per pack) Cat. No. Cat. No.
10 ml
10 ml
10 ml
10 ml
16 x 80
16 x 80
16 x 80
16 x 80
PPCO(PA) - AOR
PC - AOR
PE - AOR
PF - AOR
25 24 11
25 24 01
25 24 41
25 24 51
23 24 11
23 24 01
23 24 41
23 24 51
25 46 05
25 46 05
25 46 06
25 46 081
25 58 81
25 58 81
25 50 30
25 50 30
25 50 30
25 50 30
30 ml
30 ml
30 ml
30 ml
25 x 92
25 x 92
25 x 92
25 x 92
PPCO(PA) - AOR
PC - AOR
PE - AOR PF - AOR
25 29 61
25 29 51
25 29 65 25 29 71
23 29 61
23 29 51
23 29 65 23 29 71
25 46 15
25 46 15
25 46 16 25 46 18
1
25 58 83
25 58 83
25 58 84
25 50 61
25 50 61
25 50 61 25 50 61
50 ml
50 ml
50 ml
50 ml
29 x 103
29 x 103
29 x 103
29 x 103
PPCO(PA) - AOR
PC - AOR
PE - AOR
PF - AOR
25 32 11
25 32 01
253215
25 32 21
23 32 11
23 32 01
23 32 15
23 32 21
25 46 25
25 46 25
25 46 26
25 46 281
25 58 85
25 58 85
25 58 85
25 58 86
directly
directly
directly
directly
80 ml
80 ml
80 ml
80 ml
38 x 105
38 x 105
38 x 105
38 x 105
PPCO(PA) - AOR
PC - AOR
PE - AOR
PF - AOR
25 32 45
25 32 41
25 32 47
25 32 49
23 32 45
23 32 41
23 32 47
23 32 49
25 46 35
25 46 35
25 46 35
25 46 381
25 58 87
25 58 87
25 58 88
25 58 89
directly
directly
directly
directly
1 These screw caps are made of Polyflor too.
Overwind-protected and gas-tight
The ultimate seal for both routine and special
applications and high demands on speed.
Unique combination of screw cap and conical push-in stopper.
The Advanced Oak Ridge (AOR) system is an excellent choice for preparative centrifugation applications including protein purification, cell harvesting, pelleting applications, sterile centrifugation, extractions, density gradients and biohazardous applications.
The polypropylene sealing cap's inner conical plug has three self-seal pressure rings. They push against the inside of the tube neck, forming a triple contact seal which adds to the normal screw cap. The cap is constructed to support the tube's shoulder and neck during centrifugation. It includes a grip for easy extraction from the rotor bores. Tubes are of universal sizes and will fit rotors and adapters from all major centrifuge manufacturers.
Note: For biohazardous applications the use of optional o-rings is recommended as double seal for added safety benefits (included with all tubes with cap, except for 10 ml PPCO + PC and 30 ml PE).
PA Polyallomer PF Polyflor
® PC Polycarbonate
PPCO Polypropylene Copolymer PE Polyethylene
3.3. Advanced Oak Ridge
Tubes
page 17 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.3.2. Additional Information and Prices – Tubes complete with cap
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Tested
up to ... rpm
Tested
up to ... x g
Units
per pack
25 24 01 10 ml 9.4 ml PC - AOR 24,000 57,960 10
25 24 11 10 ml 8.9 ml PPCO(PA) - AOR 24,000 57,960 10
25 24 41 10 ml 9.7 ml PE - AOR 18,000 32,600 10
25 24 51 10 ml 9.4 ml PF - AOR 20,000 40,250 2
25 29 51 30 ml 27.9 ml PC - AOR 24,000 64,397 10
25 29 61 30 ml 25.9 ml PPCO(PA) - AOR 24,000 64,397 10
25 29 65 30 ml 24.5 ml PE - AOR 10,000 11,180 10
25 29 71 30 ml 26.4 ml PF - AOR 24,000 64,397 2
25 32 01 50 ml 40.0 ml PC - AOR 24,000 69,549 10
25 32 11 50 ml 38.0 ml PPCO(PA) - AOR 24,000 69,549 10
25 32 15 50 ml 38.9 ml PE - AOR 12,000 17,387 10
25 32 21 50 ml 42.6 ml PF - AOR 18,000 39,121 2
25 32 41 80 ml 73.1 ml PC - AOR 20,000 50,086 10
25 32 45 80 ml 76.3 ml PPCO(PA) - AOR 20,000 50,086 10
25 32 47 80 ml 69.3 ml PE - AOR 12,000 18,031 10
25 32 49 80 ml 73.0 ml PF - AOR 15,000 28,174 2
PA Polyallomer PF Polyflor® PC Polycarbonate
PPCO Polypropylene Copolymer PE Polyethylene
Attention: Kindly note packaging sizes for your orders.
3.3. Advanced Oak Ridge
Tubes
page 18 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.3.3. Additional Information and Prices – Tubes without cap
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Tested
up to ... rpm
Tested
up to ... x g
Units
per pack
23 24 01 10 ml 9.4 ml PC - AOR 24,000 57,960 10
23 24 11 10 ml 8.9 ml PPCO(PA) - AOR 24,000 57,960 10
23 24 41 10 ml 9.7 ml PE - AOR 18,000 32,600 10
23 24 51 10 ml 9.4 ml PF - AOR 20,000 40,250 2
23 29 51 30 ml 27.9 ml PC - AOR 24,000 64,397 10
23 29 61 30 ml 25.9 ml PPCO(PA) - AOR 24,000 64,397 10
23 29 65 30 ml 24.5 ml PE - AOR 10,000 11,180 10
23 29 71 30 ml 26.4 ml PF - AOR 24,000 64,397 2
23 32 01 50 ml 40.0 ml PC - AOR 24,000 69,549 10
23 32 11 50 ml 38.0 ml PPCO(PA) - AOR 24,000 69,549 10
23 32 15 50 ml 38.9 ml PE - AOR 12,000 17,387 10
23 32 21 50 ml 42.6 ml PF - AOR 18,000 39,121 2
23 32 41 80 ml 73.1 ml PC - AOR 20,000 50,086 10
23 32 45 80 ml 76.3 ml PPCO(PA) - AOR 20,000 50,086 10
23 32 47 80 ml 69.3 ml PE - AOR 12,000 18,031 10
23 32 49 80 ml 73.0 ml PF - AOR 15,000 28,174 2
3.3.4. Closures for Advanced Oak Ridge Tubes
Cat. No. Description Fits for: Units
per pack
25 46 05 Sealing cap for 10 ml AOR Tubes made of PC and PPCO (PA)
25 24 01 25 24 11
10
25 46 06 Sealing cap for 10 ml PE AOR Tubes 25 24 41 10
25 46 08 Sealing cap for 10 ml PF AOR Tubes 25 24 51 1
25 46 15 Sealing cap for 30 ml AOR Tubes made of PC and PPCO (PA)
25 29 51 25 29 61
10
25 46 16 Sealing cap for 30 ml PE-AOR Tubes 25 29 65 10
25 46 18 Sealing cap for 30 ml PF-AOR Tubes 25 29 71 1
25 46 25 Sealing cap for 50 ml AOR Tubes made of PC and PPCO (PA)
25 32 01 25 32 11
10
25 46 26 Sealing cap for 50 ml PE-AOR Tubes 25 32 15 10
25 46 28 Sealing cap for 50 ml PF-AOR Tubes 25 32 21 1
25 46 35 Sealing cap for 80 ml AOR Tubes made of PC, PPCO (PA) and PE
25 32 41 25 32 45 25 32 47
10
25 46 38 Sealing cap for 80 ml PF AOR Tubes 25 32 49 1
PA Polyallomer PF Polyflor® PC Polycarbonate
PPCO Polypropylene Copolymer PE Polyethylene
Attention: Kindly note packaging sizes for your orders.
3.3. Advanced Oak Ridge
Tubes
page 19 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.3.5. O-Rings for Advanced Oak Ridge Tubes
Cat. No. Description Fits for: Units
per pack
25 58 81 O-Ring for 10 ml AOR PE and PF 25 46 06 25 46 08
3
25 58 83 O-Ring for 30 ml AOR PPCO(PA) and PC 25 46 15 3
25 58 84 O-Ring for 30 ml AOR PF 25 46 18 3
25 58 85 O-Ring for 50 ml AOR PPCO(PA) and PC 25 46 25 25 46 26
3
25 58 86 O-Ring for 50 ml AOR PF 25 46 28 3
25 58 87 O-Ring for 80 ml AOR PPCO(PA) and PC 25 46 35 3
25 58 88 O-Ring for 80 ml AOR PE 25 46 36 3
25 58 89 O-Ring for 80 ml AOR PF 25 46 38 3
3.3.6. Adapter for Advanced Oak Ridge Tubes
Cat. No. Description Material Number of
Places For Rotor
Bores Units
per pack
25 50 30 Adapter Plastic 1 50 ml 2
25 50 61 Adapter Plastic 1 50 ml 2
PA Polyallomer PF Polyflor® PC Polycarbonate
PPCO Polypropylene Copolymer PE Polyethylene
Attention: Kindly note packaging sizes for your orders.
3.3. Advanced Oak Ridge
Tubes
page 20 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.4.0. General Information
Overwind-protected and gas-tight
One-piece sealing cap with O-ring guarantees leak-proof seal
Maximum filling volume and maximum speed
Accessories that increase bottle lifespan
Available are high-speed centrifuge bottles with volumes of 200, 250, 290, 500, 650, 750 and 1000 ml for angle and swing-out rotors.
A special black polypropylene bottle which reduces UV light transmission is available for light-sensitive analyses such as fluorescent studies and work with retinal cells.
A wide neck bottle design with gently sloping shoulders allows easy decanting of supernatants without liquid hang-up and pellet disturbance. The cap provides neck support, preventing bottle collapse even after prolonged centrifugation. A polypropylene cover support ring increases the lifespan of the 500 ml bottle by providing extra support to the neck area during centrifugation. The cover support ring can also be used to facilitate opening and closing of the 250, 290 and 500 ml bottles.
Note: During an actual centrifugation run the cover support ring should only be used with the 500 ml bottles.
The one-piece polypropylene sealing cap with a well-embedded silicone o-ring provides a leak-proof seal and is interchangeable between the 250, 290, 500 and 1000 ml bottles. The cap is molded to match exactly the threads of the bottle and provides a leak-proof seal. A tight seal is guaranteed even at maximum speed.
Polypropylene pads are available for use with the 250 and 290 ml flat bottom bottles and the 250 ml round bottom bottles. The pads fill the gap that would exist between the bottle bottom and the rotor cavity, eliminating unnecessary stress and cold flow of the plastics in this area during the run.
3.4. Bottles
page 21 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.4.1. Ordering Information Bottom Support
Pads for rotor bores
250 ml 500 ml
Nominal Volume
Dimensions (mm)
Ø x Length
Material and Form
Cat. No. Bottles
complete
Cat. No. Bottles
Cat. No. Cap
Cat. No. O-Rings
(3 pieces per pack) Cat. No. Cat. No.
200 ml
200 ml
200 ml
200 ml
56 x 112
56 x 112
56 x 112
56 x 112
PC – CB/W
PC – FB/W
PPCO(PA) – CB/W
PPCO(PA) – FB/W
25 33 75
25 33 71
25 33 77
25 33 73
23 33 75
23 33 71
23 33 77
23 33 73
25 46 55
25 46 55
25 46 55
25 46 55
25 58 53
25 58 53
25 58 53
25 58 53
250 ml
250 ml
250 ml
250 ml
250 ml
250 ml
250 ml
250 ml
250 ml
250 ml
62 x 122
62 x 122
62 x 122
62 x 122
62 x 122
62 x 122
62 x 122
62 x 122
62 x 122
62 x 122
PC – FB/W
PC – RB/W
PE – FB/W
PE – RB/W
PF – FB/W
PF – RB/W
PP/black – FB/W
PPCO(PA) – FB/W
PPCO(PA) – RB/W
PP – RB/W
25 34 01
25 34 41
25 34 31
25 34 47
25 34 39
25 34 49
25 34 12
25 34 21
25 34 45
25 34 43
23 34 01
23 34 41
23 34 31
23 34 47
23 34 21
23 34 45
23 34 43
25 46 60
25 46 60
25 46 60
25 46 60
25 46 63
25 46 63
included
25 46 60
25 46 60
25 46 60
25 58 55
25 58 55
25 58 55
25 58 55
25 58 57
25 58 57
25 58 55
25 58 55
25 58 55
25 58 55
25 51 811
25 51 90
25 51 811
25 51 90
25 51 811
25 51 90
25 51 811
25 51 811
25 51 90
25 51 90
290 ml
290 ml
62 x 137
62 x 137
PC – FB/W3
PE – FB/W3
25 34 81
25 34 87
23 34 81
23 34 87
25 46 60
25 46 60
25 58 55
25 58 55
25 51 811
25 51 811
500 ml
500 ml
500 ml
500 ml
500 ml
70 x 165
70 x 165
70 x 165
70 x 165
98 x 114
PC – FB/W
PE – FB/W
PP/black – FB/W
PPCO(PA) – FB/W
PPCO(PA) – FB/W
25 35 012
25 35 312
25 35 122
25 35 212
25 35 51
23 35 01
23 35 31
23 35 21
23 35 51
25 46 60
25 46 60
included
25 46 60
25 46 60
25 58 55
25 58 55
25 58 55
25 58 55
25 58 55
directly
directly
directly
directly
AS 4.500 only
650 ml
650 ml
750 ml
750 ml
98 x 136
98 x 136
98 x 152
98 x 152
PC – FB/W
PP – FB/W
PC – FB/W
PPCO(PA) – FB/W
25 35 90
25 35 91
25 35 80
25 35 81
23 35 90
23 35 91
23 35 80
23 35 81
25 46 60
25 46 60
25 46 60
25 46 60
25 58 55
25 58 55
25 58 55
25 58 55
directly
directly
directly
directly
1,000 ml
1,000 ml
1,000 ml
1,000 ml
98 x 175
98 x 175
98 x 175
98 x 175
PC – FB/W
PC – FB/W + SR
PPCO(PA) – FB/W
PPCO(PA) – FB/W+SR
25 35 62
25 35 65
25 35 72
25 35 75
23 35 62
23 35 62
23 35 72
23 35 72
25 46 60
25 46 62
25 46 60
25 46 62
25 58 55
25 58 55
25 58 55
25 58 55
directly
directly
directly
directly
1 Bottom support pads not for use in all swing-out rotors and angle rotors
JA-14 (Beckman) and HFA-14.290 (Heraeus) and AF 6.250 + AF 8.250 (Herolab). 2 For safety reasons always use with cover support ring (Cat. No. 25 52 41).
Bottles cannot be used in rotor JA-10 (Beckman). 3 290 ml bottles do not fit in rotors AF 6.250 (Herolab) and
JA-14 (Beckman)
PA Polyallomer CB Conical bottom FL Flange / Rim
PPCO Polypropylene Copolymer FB Flat bottom G Graduated
PP Polypropylene RB Round bottom LC Loop cap
PE Polyethylene W Wide neck
PC Polycarbonate PF Polyflor® SR Support ring
3.4. Bottles
page 22 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.4.2. Additional Information and Prices – Bottles complete with cap
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Tested
up to … rpm
Tested
up to … x g
Units
per pack
25 33 71 200 ml 186.0 ml PC – FB/W 10,000 16,323 6
25 33 73 200 ml 168.4 ml PPCO – FB/W 10,000 16,323 6
25 33 75 200 ml 179.0 ml PC – CB/W 10,000 16,323 6
25 33 77 200 ml 156.9 ml PPCO(PA) – CB/W 10,000 16,323 6
25 34 01 250 ml 232.5 ml PC – FB/W 14,400 33,847 6
25 34 12 250 ml 227.3 ml PP/black – FB/W 13,000 27,585 6
25 34 21 250 ml 225.1 ml PPCO(PA) – FB/W 14,400 33,847 6
25 34 31 250 ml 239.0 ml PE – FB/W 13,500 29,749 6
25 34 39 250 ml 231.6 ml PF – FB/W 12,000 23,505 2
25 34 41 250 ml 203.3 ml PC – RB/W 14,400 33,847 6
25 34 43 250 ml 213.3 ml PP – RB/W 14,400 33,847 6
25 34 45 250 ml 213.5 ml PPCO(PA) – RB/W 14,400 33,847 6
25 34 47 250 ml 213.5 ml PE – RB/W 13,500 29,749 6
25 34 49 250 ml 213.2 ml PF – RB/W 12,000 23,505 2
25 34 81 290 ml 273.5 ml PC – FB/W 14,400 33,847 6
25 34 87 290 ml 275.5 ml PE – FB/W 13,500 29,749 6
25 35 012 500 ml 432.1 ml PC – FB/W 10,500 20,560 6
25 35 122 500 ml 430.2 ml PP/black – FB/W 10,500 20,560 2
25 35 212 500 ml 432.1 ml PPCO(PA) – FB/W 10,500 20,560 6
25 35 312 500 ml 431.5 ml PE – FB/W 7,500 10,226 6
25 35 51 500 ml 503.0 ml PPCO(PA) – FB/W 5,200 5,290 4
25 35 90 650 ml 670.0 ml PC – FB/W 3 4,000 4,936 4
25 35 91 650 ml 668.0 ml PP – FB/W 3 4,000 4,936 4
25 35 80 750 ml 760.0 ml PC – FB/W 3 4,000 4,936 4
25 35 81 750 ml 762.0 ml PPCO(PA) – FB/W 3 4,000 4,936 4
25 35 62 1,000 ml 900.0 ml PC – FB/W 3 4,000 4,936 4
25 35 65 1,000 ml 900.0 ml PC – FB/W / SR 8,000 12,042 4
25 35 72 1,000 ml 887.0 ml PPCO(PA) – FB/W 3 4,000 4,936 4
25 35 75 1,000 ml 885.0 ml PPCO(PA) – FB/W SR 8,000 12,042 4 2 For safety reasons always use with cover support ring (Cat. No. 25 52 41).
Bottles cannot be used in rotor JA-10 (Beckman). 3 If used with Sealing cap/Support ring Combination (cat. no. 25 35 65) the max speed is 8,000 rpm in a fixed angle rotor.
PA Polyallomer CB Conical bottom FL Flange / Rim
PPCO Polypropylene Copolymer FB Flat bottom G Graduated
PP Polypropylene RB Round bottom LC Loop cap
PE Polyethylene W Wide neck
PC Polycarbonate PF Polyflor® SR Support ring
Attention: Kindly note packaging sizes for your orders.
3.4. Bottles
page 23 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.4.3. Additional Information and Prices – Bottles without cap
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Tested
up to … rpm
Tested
up to … x g
Units
per pack
23 33 71 200 ml 186.0 ml PC – FB/W 10,000 16,323 6
23 33 73 200 ml 168.4 ml PPCO – FB/W 10,000 16,323 6
23 33 75 200 ml 179.0 ml PC – CB/W 10,000 16,323 6
23 33 77 200 ml 156.9 ml PPCO(PA) – CB/W 10,000 16,323 6
23 34 01 250 ml 232.5 ml PC – FB/W 14,400 33,847 6
23 34 21 250 ml 225.1 ml PPCO(PA) – FB/W 14,400 33,847 6
23 34 31 250 ml 239.0 ml PE – FB/W 13,500 29,749 6
23 34 39 250 ml 231.6 ml PF – FB/W 12,000 23,505 2
23 34 41 250 ml 203.3 ml PC - RB/W 14,400 33,847 6
23 34 43 250 ml 213.3 ml PP - RB/W 14,400 33,847 6
23 34 45 250 ml 213.5 ml PPCO(PA) – RB/W 14,400 33,847 6
23 34 47 250 ml 213.5 ml PE - RB/W 13,500 29,749 6
23 34 49 250 ml 213.2 ml PF – RB/W 12,000 23,505 2
23 34 81 290 ml 273.5 ml PC - FB/W 14,400 33,847 6
23 34 87 290 ml 275.5 ml PE - FB/W 13,500 29,749 6
23 35 012 500 ml 432.1 ml PC - FB/W 10,500 20,560 6
23 35 212 500 ml 432.1 ml PPCO(PA) – FB/W 10,500 20,560 6
23 35 312 500 ml 431.5 ml PE - FB/W 9,000 14,725 6
23 35 51 500 ml 503.0 ml PPCO(PA) – FB/W 5,200 5,290 4
23 35 90 650 ml 670.0 ml PC - FB/W 4,000 4,936 4
23 35 91 650 ml 668.0 ml PP - FB/W 4,000 4,936 4
23 35 80 750 ml 760.0 ml PC - FB/W 4,000 4,936 4
23 35 81 750 ml 762.0 ml PPCO(PA) – FB/W 4,000 4,936 4
23 35 62 1,000 ml 900.0 ml PC - FB/W 4,000 4,936 4
23 35 72 1,000 ml 887.0 ml PPCO(PA) – FB/W 4,000 4,936 4 2 For safety reasons always use with cover support ring (Cat. No. 25 52 41).
Bottles cannot be used in rotor JA-10 (Beckman).
PA Polyallomer CB Conical bottom FL Flange / Rim
PPCO Polypropylene Copolymer FB Flat bottom G Graduated
PP Polypropylene RB Round bottom LC Loop cap
PE Polyethylene W Wide neck
PC Polycarbonate PF Polyflor® SR Support ring
Attention: Kindly note packaging sizes for your orders.
3.4. Bottles
page 24 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.4.4. Closures and Support Rings for Bottles
Cat. No. Description Fits for: Units
per pack
25 46 55 Sealing cap for 200 ml
25 33 71 25 33 73
25 33 75 25 33 77
6
25 46 60
Sealing cap for 250, 290, 500 und 1,000 ml
25 34 01 25 34 21 25 34 41 24 34 43 25 34 45 25 34 81
25 35 01 25 35 21 25 35 51 25 35 80 25 35 81 25 35 90 25 35 91 25 35 62 25 35 72
6
25 46 62 Combination (for 1,000 ml) Sealing cap with support ring 25 35 65 25 35 75 1
25 46 63 Sealing cap for 250 ml PF
25 34 39 25 34 49 1
25 52 41 Support ring for 500 ml cap and closing device for 250/290/500 ml
6
3.4.5. O-Rings for Bottle Sealing Caps
Cat. No. Description Fits for: Units
per pack
25 58 53 O-Ring for bottle sealing caps 200 ml 25 46 55 3
25 58 55 O-Ring for bottle sealing caps 25 46 60 3
25 58 57 O-Ring for bottle sealing caps (PF bottles) 25 46 63 3
3.4.6. Bottom Support Pads for Bottles
Cat. No. Description Fits for: Units
per pack
25 51 81
Bottom support pad for 250/290 ml FB
25 34 01 25 34 12 25 34 21 25 34 31
25 34 39 25 34 81 25 34 87
6
25 51 90
Bottom support pad for 250 ml RB
25 34 41 25 34 43 25 34 45
25 34 47 25 34 49
6
Attention: Kindly note packaging sizes for your orders.
3.4. Bottles
page 25 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.5.1.1. Ordering Information – Tubes
Nominal Volume
Dimension (mm)
Ø x Length Material and Form
Cat. No. Tubes
Cat. No. Cap
Fits directly into these rotors:
2.0 ml 2.0 ml
8 x 51 8 x 51
PA - thin-walled PC - thick-walled
25 20 70 25 20 20
TFT 80.2, TST 60.2
4.4 ml 4.4 ml 4.4 ml
11 x 60 11 x 60 11 x 60
PA - thin-walled PC - thick-walled PC - thick-w. w. thread
25 21 40 25 21 50 25 22 20
25 46 94
TFT 80.4, TST 60.4 SW 60Ti, SW 56Ti
5.0 ml 5.0 ml 5.0 ml
13 x 51 13 x 51 13 x 51
PA - thick-walled PA - thin-walled PC - thick-walled
25 22 60 25 21 90 25 22 40
TST 55.5, AH-650, SW 65 SW 55Ti, SW 50.1, SW 50
SW 39, TLA 100-3
6.5 ml 6.5 ml 6.5 ml 6.5 ml
13 x 64 13 x 64 13 x 64 13 x 64
PA - thick-walled PA - thin-walled PC - thick-walled PC - thick-w. w. thread
25 23 50 25 23 40 25 22 80 25 22 90
25 46 91
TFT 45.6 50.4Ti, 50.3Ti, 40.3
13.2 ml 13.5 ml 13.5 ml 13.5 ml
14 x 89 16 x 76 16 x 76 16 x 76
PA - thin-walled PA - thin-walled PC - thick-walled PC - thick-w. w. thread
25 23 90 25 24 30 25 24 80 25 24 90
25 46 88
TST 41.13, SW 41Ti
TFT 80.13, TFT 75.13, TFT 65.13 TFT 60.13, TFT 50.13, TFT 32.13
80Ti, 75Ti, 70.1Ti, 65, 50Ti, 40, SW 36
14.0 ml 14.0 ml 17.0 ml 17.0 ml
14 x 95 14 x 95 16 x 102 16 x 102
PA - thin-walled PC - thick-walled PA - thin-walled PC - thick-walled
25 23 60 25 25 60 25 26 20 25 26 40
TST 41.14, SW 40Ti
TST 28.17, AH-629 SW 27.1, SW 28.1
38.5 ml 38.5 ml 38.5 ml 38.5 ml
25 x 89 25 x 89 25 x 89 25 x 89
PA - thick-walled PA - thin-walled PC - thick-walled PC - thick-w. w. thread
25 30 60 25 30 50 25 30 40 25 30 20
25 46 85
TFT 70.38, TFT 65.38, TFT 55.38 TFT 50.38, TST 28.38, AH-629
70Ti, 60Ti, 55.2Ti, 30.2Ti 42.1, SW 27, (SW 28 without lid)
94.0 ml 94.0 ml 94.0 ml
38 x 102 38 x 102 38 x 102
PA - thick-walled PC - thick-walled PC - thick-w. w. thread
25 32 60 25 32 80 25 32 90
25 46 82 TFT 45.94, 45Ti, 35
3.5.1.2. Ordering Information – Ultra-Centrifuge Bottle with Delrin closure and Neopren ring for ultra-rotors TFA 20.250 and Type 19
Nominal Volume
Dimension (mm)
Ø x Length
Material and Form (with closure)
Cat. No. Bottle
complete
Cat. No. Bottle
only
Cat. No. Cap
Cat. No. O-Rings
(3 pieces per pack)
250 ml 60 x 122 PA - FB/W 25 34 25 23 34 25 25 46 65 25 58 65
Note: This ultra-centrifuge bottle has other dimensions than a high-speed bottle with the same
volume. Hence they will not fit the bores of high-speed rotors and vice versa.
PA Polyallomer FB Flat bottom W Wide neck
PC Polycarbonate RB Round bottom
3.5. Ultra
Centrifuge Tubes
and Bottle
page 26 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.5.2.1. Additional Information and Prices – Tubes without cap
Cat. No. Tube
Nominal Volume
Filling Volume
Material and Form
Speed
max ... rpm (cpltly. filled)
Former Kontron No.
Units
per pack
25 20 20 2.0 ml 0.6 ml PC - th i ck -wa l le d 45,000 91-90289 50
25 20 70 2.0 ml 1.3 ml PA - th in -w a l l ed 80,000 91-90288 50
25 21 40 4.4 ml 3.3 ml PA - th in -w a l l ed 80,000 91-90212 50
25 21 50 4.4 ml 2.2 ml PC - th i ck -wa l le d 50,000 91-90214 50
25 22 20 4.4 ml 2.7 ml PC - t h i c k - w . w . t h r e a d 50,000 91-90275 50
25 21 90 5.0 ml 5.0 ml PA - th in -w a l l ed 55,000 91-90219 50
25 22 40 5.0 ml 3.4 ml PC - th i ck -wa l le d 55,000 91-90224 50
25 22 60 5.0 ml 3.4 ml PA - th i ck -wa l le d 50,000 91-90223 50
25 22 80 6.5 ml 2.8 ml PC - th i ck -wa l le d 40,000 91-90229 50
25 22 90 6.5 ml 4.5 ml PC - t h i c k - w . w . t h r e a d 45,000 91-90241 50
25 23 40 6.5 ml 5.8 ml PA - th in -w a l l ed 45,000 91-90227 50
25 23 50 6.5 ml 2.8 ml PA - th i ck -wa l le d 35,000 91-90228 50
25 23 90 13.2 ml 11.3 ml PA - th in -w a l l ed 41,000 91-90221 50
25 24 30 13.5 ml 11.0 ml PA - th in -w a l l ed 80,000 91-90202 50
25 24 70 13,5 ml 8.5 ml PA - th in -w a l l ed 45,000 91-90203 50
25 24 80 13.5 ml 8.5 ml PC - th i ck -wa l le d 40,000 91-90205 50
25 24 90 13.5 ml 9.5 ml PC - t h i c k - w . w . t h r e a d 40,000 91-90235 50
25 23 60 14.0 ml 12.0 ml PA - th in -w a l l ed 41,000 91-90215 50
25 25 60 14.0 ml 9.0 ml PC - th i ck -wa l le d 30,000 91-90382 50
25 26 20 17.0 ml 15.8 ml PA - th in -w a l l ed 28,000 91-90217 50
25 26 40 17.0 ml 12.5 ml PC - th i ck -wa l le d 28,000 91-90195 50
25 30 20 38.5 ml 32.5 ml PC - t h i c k - w . w . t h r e a d 50,000 91-90236 50
25 30 40 38.5 ml 29.0 ml PC - th i ck -wa l le d 50,000 91-90299 50
25 30 50 38.5 ml 34.0 ml PA - th in -w a l l ed 70,000 91-90196 50
25 30 60 38.5 ml 29.0 ml PA - th i ck -wa l le d 45,000 91-90198 50
25 32 60 94.0 ml 77.0 ml PA - th i ck -wa l le d 45,000 91-90208 25
25 32 80 94.0 ml 77.0 ml PC - th i ck -wa l le d 45,000 91-90209 25
25 32 90 94.0 ml 88.0 ml PC - t h i c k - w . w . t h r e a d 40,000 91-90237 25 Tubes were tested at 4°C for 24 hours. Since there are many factors that may influece the performance characteristics and lifespan of centrifuge tubes the information given above has been compiled as a general guideline but, in no case, expresses absolute guarantee of a product in a laboratory situation.
3.5.2.2. Additional Information and Prices – Bottle
Cat. No. Bottle
Nominal Volume
Filling Volume
Material and Form
Speed
max ... rpm (cpltly. filled)
Former Kontron No.
Units
per pack
23 34 25 250 ml 191.5 ml PA - FB/W without cap 20,000 6
25 34 25 250 ml 191.5 ml PA - FB/W complete with cap 20,000 91-90460 6
PA Polyallomer FB Flat bottom W Wide neck
PC Polycarbonate RB Round bottom
Attention: Kindly note packaging sizes for your orders
3.5. Ultra
Centrifuge Tubes
and Bottle
page 27 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.5.3. Closures for Ultra-Centrifuge Tubes and Bottle
All closures are overwind-protected and gas-tight.
Cat. No. Description Fits for: Former
Kontron No.
Units
per pack
25 46 65 Sealing cap fur UC bottle 25 34 25 1
25 46 82 Screw cap for 94 ml 25 32 90 96-00131 1
25 46 85 Screw cap for 38.5 ml 25 30 20 96-00130 1
25 46 88 Screw cap for 13.5 ml 25 24 90 96-00129 1
25 46 91 Screw cap for 6.5 ml 25 22 90 96-00151 1
25 46 94 Screw cap for 4.4 ml 25 22 20 96-00165 1
3.5.4. O-Rings for Ultra-Centrifuge Tubes and Bottle
Cat. No. Description Fits for: Former
Kontron No.
Units
per pack
25 58 65 O-Rings for UC bottle 25 34 25 3
25 59 00 O-Ring for screw cap – 94 ml 25 46 82 34-80035 1
25 59 05 O-Ring for screw cap – 38.5 ml 25 46 85 34-80034 1
25 59 10 O-Ring for screw cap – 13.5 ml 25 46 88 34-80036 1
25 59 15 O-Ring for screw cap – 6.5 ml 25 46 91 34-80033 1
25 59 20 O-Ring for screw cap – 4.4 ml 25 46 94 34-80045 1
3.5.5. Other accessories for Ultra-Centrifuge Tubes
Cat. No. Description Former
Kontron No.
Units
per pack
25 49 00 Extractor Tool for UC tubes 92-00108 1
Attention: Kindly note packaging sizes for your orders.
3.5. Ultra
Centrifuge Tubes
and Bottle
page 28 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
3.6.1. Accessories
Cat. No. Description Units
per pack
25 80 20 Extractor tool for 50 ml with rim 1
25 81 20 Extractor tool for bottom support pads 1
25 81 60 Extractor tool M4 1
25 80 30 Extractor tool M6 1
25 80 70 Cleaning brush for all rotors 50 ml 1
25 80 80 Cleaning brush for all rotors 14/15/16 ml 1
25 80 90 Cleaning brush for all rotors 250/290 ml 1
25 80 60 Rotor stand for all rotors with conical bore (e. g. for Sorvall etc.)
1
Attention: Kindly note packaging sizes for your orders.
3.6. Other
Access-ories
page 29 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Volume
approx. Ø in mm of
Rotor Bore x
max. length
The tubes will fit into the next larger sized rotor with adapters from all manufacturers. Swing-out Rotors are listed without the bucket resp. adapter numbers. Manufacturers not listed have in most cases an identical size of the rotor compartments. The given information is as accurate as possible. Errors or incompleteness could be contained. Herolab is not responsible for any damage caused by the given information. Herolab reserves the right to modify any part without prior notice.
10 ml 16.1 x 80 Herolab AFH 20.180 or AF 20.10 Sigma 12111, 12141, 12157 and 12168 Beckman JA-21, JS-24.15, F1010 and S0410
30 ml 25.3 x 92 Sigma 12139, 12158 and 12172 Beckman JS-24.38, F0630 Hermle 220.76 V02, 220.76 V03 and 221.10 V02
50 ml 28.7 x 103
Herolab AF 8.50.1, A 8.24, AF 8.50.2, A 12.17, AS 4.7 and AS 4.13 Sigma 12150, 12156 and 12160 Jouan AK(L) 50.22, AK(L) 50.17 and FAJ-20C Sorvall SS-34, SA-300, SA-600, F-28/50, A-500, A/S-400, LA/S-400, SL-50RT, HB-4 and HB-6 Beckman JA-20, JA-12, JA-17, JA-25.50, JA-30.50Ti, JS-13, JS-13.1, F0650, F0850 and TA-14-50 Fiberlite F21(B,S or J)8x50(y) and F18(B,S or J)12x50(y) Hermle 220.80 V02, 220.80 V03 and 221.22 V01
80 ml 38.1 x 105
Herolab AFH 6.180 or AF 6.94 (6.80), A 8.20 and AS 4.13 Sigma 121559, 12159 and 12165 Jouan AG 100.18, AG 100.14, AK(L) 100.21, SWK 100.13 and SWG 100.9 Sorvall SA-800 Beckman JA-18, F0485, F0685 and FX6100 Fiberlite F20(B,S or J)6x100 Hermle 220.78 V02, 220.78 V03, 221.18 V01 and 221.20 V01
200 ml 56.5 x 112 Herolab ASH 4.055, AS 4.500 or TS 4.200 Sigma 11133, 11140, 11150, 11156, 11180, 11650, 11800 and 11801
250 ml 61.8 x 122
Herolab AF 6.250, AF 8.250, A 6.14, AFH-4.090 and AS 4.7 Sigma 11150, 11180, 11650, 11800, 11801, 12256 and 12258 Jouan AG 290.9, AK(L) 250.14 and FAJ-14C Sorvall GSA, SLA-1000, SLA-1500, SLC-1500, H-1000B, RTH-250, H-2000B and HS-4 Beckman JA-14, JLA-16.250, TA-10.250, JS-7.5 and SX4250 Fiberlite F14(B,S or J)6x250(y) and F16(B,S or J)4x250(y) Hermle 221.21 V01, 221.08 V01 and 221.15 V01
290 ml 61.8 x 137
Herolab A 6.14 Sorvall GSA and SLA-1500 Jouan AG 290.9 and AK 250.14 Beckman JA-14, JLA-16.250 and JS-7.5
500 ml 69.5 x 165
Herolab AF 6.500, AF 8.500 and A 6.9 Sigma 11150, 11650, 11800, 11801, 12500 and 12505 Jouan FAJ-10C and AK(L) 500.11 Sorvall GS-3, SLA-3000, SLC-3000 Beckman JLA-10.500 Fiberlite F10(B,BA,S or J)6x500(y) and F12S6x500y
500 ml 97.5 x 114 Herolab AS 4.500
650 ml 97.5 x 136 Herolab AS 4.750 Sigma 11650, 11800 and 11801
750 ml 97.5 x 152
Herolab AS 4.750 Sigma 11650, 11800 and 11801 Sorvall SH-3000, TTH-750 and RTH-750 Beckman JS-4.3 SX4750 SX4750A Hermle 220.70 V06
1000 ml 97.5 x 175
Herolab AF 4.1000, AF 6.1000 and AS 4.1000 Sigma 12510, 11800 and 11801 Sorvall SLC-4000, SLC-6000, HL-4, HG-4L, H-4000, H-6000 Beckman JS-4.0 Fiberlite F(7S,8B, 9B,9S,9J)4x1000y, F6(B,S or J)6x1000y and F8(B,BA,S or J)6x1000y Hermle 220.70 V05
4. Compati-bility with
rotors of other
manufac-turers
page 30 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Cat. No. Item Units per pack
23 24 01 Tubes 10 ml PC-AOR without screw cap 10
23 24 11 Tubes 10 ml PPCO-AOR without screw cap 10
23 24 41 Tubes 10 ml PE-AOR without screw cap 10
23 24 51 Tubes 10 ml PF-AOR without screw cap 2
23 29 51 Tubes 30 ml PC-AOR without screw cap 10
23 29 61 Tubes 30 ml PPCO-AOR without screw cap 10
23 29 65 Tubes 30 ml PE-AOR without screw cap 10
23 29 71 Tubes 30 ml PF-AOR without screw cap 2
23 32 01 Tubes 50 ml PC-AOR without screw cap 10
23 32 11 Tubes 50 ml PPCO-AOR without screw cap 10
23 32 15 Tubes 50 ml PE-AOR without screw cap 10
23 32 21 Tubes 50 ml PF-AOR without screw cap 2
23 32 41 Tubes 80 ml PC-AOR without screw cap 10
23 32 45 Tubes 80 ml PPCO-AOR without screw cap 10
23 32 47 Tubes 80 ml PE-AOR without screw cap 10
23 32 49 Tubes 80 ml PF-AOR without screw cap 2
23 33 71 Bottles 200 ml PC-FB without screw cap 6
23 33 73 Bottles 200 ml PP-FB without screw cap 6
23 33 75 Bottles 200 ml PC-CB without screw cap 6
23 33 77 Bottles 200 ml PPCO-CB without screw cap 6
23 34 01 Bottles 250 ml PC-FB without screw cap 6
23 34 21 Bottles 250 ml PPCO-FB without screw cap 6
23 34 25 Bottles 200 ml PA-FB/W UC without screw cap 6
23 34 31 Bottles 250 ml PE-FB without screw cap 6
23 34 39 Bottles 250 ml PF-FB with screw cap 2
23 34 41 Bottles 250 ml PC-RB without screw cap 6
23 34 43 Bottles 250 ml PP-RB without screw cap 6
23 34 45 Bottles 250 ml PPCO-RB without screw cap 6
23 34 47 Bottles 250 ml PE-RB without screw cap 6
23 34 49 Bottles 250 ml PF-RB with screw cap 2
23 34 81 Bottles 290 ml PC-FB without screw cap 6
23 34 87 Bottles 290 ml PE-FB without screw cap 6
23 35 01 Bottles 500 ml PC-FB without screw cap 6
23 35 21 Bottles 500 ml PPCO-FB without screw cap 6
23 35 31 Bottles 500 ml PE-FB without screw cap 6
23 35 51 Bottles 500 ml PPCO-FB without screw cap 4
23 35 62 Bottles 1000 ml PC-FB without screw cap 4
23 35 72 Bottles 1000 ml PPCO-FB without screw cap 4
23 35 80 Bottles 750 ml PC-FB without screw cap 4
23 35 81 Bottles 750 ml PP-FB without screw cap 4
23 35 90 Bottles 650 ml PC-FB without screw cap 4
23 35 91 Bottles 650 ml PP-FB without screw cap 4
25 10 10 Tubes 3 ml Duran Glass. RB 10
25 10 20 Tubes 5 ml Borex Glass, RB 10
25 10 40 Tubes 10 ml Duran Glass, RB 10
25 10 60 Tubes 10 ml Duran Glass, C/G 10
25 10 91 Tubes 15 ml HS Glass, RB 6
25 11 00 Tubes 12 ml Borex Glass, RB 10
25 11 10 Tubes 30 ml Borex Glass, RB 10
25 11 41 Tubes 30 ml HS Glass, RB 6
25 12 60 Tubes 45 ml Borex Glass, RB 10
25 12 70 Tubes 200 ml Duran Glass, RB 2
25 12 80 Tubes 15 ml Duran Glass, RB 10
25 20 00 Tubes 1.0 ml PS-RB / pck. with 1.000 pieces 1000
25 20 20 Tubes 2.0 ml PC thick-walled UC / pck. with 50 pieces 50
page 31 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Cat. No. Item Units per pack
25 20 50 Tubes 1.5 ml PP-CB with lid (Eppendorf) / pck. with 1.000 pieces 1000
25 20 70 Tubes 2.0 ml PA thin-walled UC / pck. with 50 pieces 50
25 21 40 Tubes 4.4 ml PA thin-walled UC / pck. with 50 pieces 50
25 21 50 Tubes 4.4 ml PC thick-walled UC / pck. with 50 pieces 50
25 21 90 Tubes 5.0 ml PA thin-walled UC / pck. with 50 pieces 50
25 22 00 Tubes 5.0 ml PS-RB / pck. with 1.000 pieces 1000
25 22 20 Tubes 4.4 ml PC thick-walled with thread UC / pck. with 50 pieces 50
25 22 30 Tubes 4.5 ml PP-RB / pck. with 1.000 pieces 1000
25 22 40 Tubes 5.0 ml PC thick-walled UC / pck. with 50 pieces 50
25 22 60 Tubes 5.0 ml PA thick-walled UC / pck. with 50 pieces 50
25 22 80 Tubes 6.5 ml PC thick-walled UC / pck. with 50 pieces 50
25 22 90 Tubes 6.5 ml PC thick-walled with thread UC / pck. with 50 pieces 50
25 23 40 Tubes 6.5 ml PA thin-walled UC / pck. with 50 pieces 50
25 23 50 Tubes 6.5 ml PA thin-walled UC / pck. with 50 pieces 50
25 23 60 Tubes 14.0 ml PA thin-walled UC / pck. with 50 pieces 50
25 23 90 Tubes 13.2 ml PA thin-walled UC / pck. with 50 pieces 50
25 24 01 Tubes 10 ml PC-AOR with screw cap 10
25 24 11 Tubes 10 ml PPCO-AOR with screw cap 10
25 24 30 Tubes 13.5 ml PA thin-walled UC / pck. with 50 pieces 50
25 24 41 Tubes 10 ml PE-AOR with screw cap 10
25 24 51 Tubes 10 ml PF-AOR with screw cap 2
25 24 80 Tubes 13.5 ml PC thick-walled UC / pck. with 50 pieces 50
25 24 90 Tubes 13.5 ml PC thick-walled with thread UC / pck. with 50 pieces 50
25 25 60 Tubes 14.0 ml PC thick-walled UC / pck. with 50 pieces 50
25 25 70 Tubes 14 ml PC-RB 10
25 25 80 Tubes 14 ml PP-RB 10
25 25 90 Tubes 14 ml PF-RB 2
25 26 10 Tubes 13.0 ml PP-RB 10
25 26 20 Tubes 17.0 ml PA thin-walled UC / pck. with 50 pieces 50
25 26 40 Tubes 17.0 ml PC thick-walled UC / pck. with 50 pieces 50
25 26 60 Tubes 14 ml PE-RB 10
25 26 90 Tubes 14 ml PA-RB 10
25 27 00 Tubes 16 ml PC-RB/FL 10
25 27 20 Tubes 16 ml PPCO-RB/FL 10
25 27 40 Tubes 16 ml PE-RB/FL 10
25 27 51 Tubes 16 ml PF-RB/FL 2
25 29 51 Tubes 30 ml PC-AOR with screw cap 10
25 29 61 Tubes 30 ml PPCO-AOR with screw cap 10
25 29 65 Tubes 30 ml PE-AOR with screw cap 10
25 29 71 Tubes 30 ml PF-AOR with screw cap 2
25 30 20 Tubes 38.5 ml PC thick-walled with thread UC / pck. with 50 pieces 50
25 30 40 Tubes 38.5 ml PC thick-walled UC / pck. with 50 pieces 50
25 30 50 Tubes 38.5 ml PA thin-walled UC / pck. with 50 pieces 50
25 30 60 Tubes 38.5 ml PA thick-walled UC / pck. with 50 pieces 50
25 30 90 Tubes 70 ml PC-RB/G 10
25 31 00 Tubes 50 ml PC-RB/FL 10
25 31 05 Tubes 50 ml PC-RB/FL with Loop Cap 10
25 31 30 Tubes 50 ml PE-RB/FL 10
25 31 45 Tubes 50 ml PPCO-RB/FL with Loop Cap 10
25 31 51 Tubes 50 ml PF-RB/FL 2
25 31 60 Tubes 50 ml PPCO-RB/FL 10
25 31 90 Tubes 70 ml PP-RB 10
25 32 01 Tubes 50 ml PC-AOR with screw cap 10
25 32 11 Tubes 50 ml PPCO-AOR with screw cap 10
page 32 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Cat. No. Item Units per pack
25 32 15 Tubes 50 ml PE-AOR with screw cap 10
25 32 21 Tubes 50 ml PF-AOR with screw cap 2
25 32 41 Tubes 80 ml PC-AOR with screw cap 10
25 32 45 Tubes 80 ml PPCO-AOR with screw cap 10
25 32 47 Tubes 80 ml PEC-AOR with screw cap 10
25 32 49 Tubes 80 ml PF-AOR with screw cap 2
25 32 60 Tubes 94.0 ml PA thick-walled UC / pck. with 25 pieces 25
25 32 80 Tubes 94.0 ml PC thick-walled UC / pck. with 25 pieces 25
25 32 90 Tubes 94.0 ml PC thick-walled with thread UC / pck. with 25 pieces 25
25 33 00 Tubes 100 ml PC-RB/G 2
25 33 10 Tubes 120 ml PP-RB 10
25 33 20 Tubes 100 ml PC-RB/G 10
25 33 71 Bottles 200 ml PC-FB with screw cap 6
25 33 73 Bottles 200 ml PPCO-FB with screw cap 6
25 33 75 Bottles 200 ml PC-CB with screw cap 6
25 33 77 Bottles 200 ml PPCO-CB with screw cap 6
25 34 01 Bottles 250 ml PC-FB with screw cap 6
25 34 12 Bottles 250 ml PP black FB with screw cap 6
25 34 21 Bottles 250 ml PPCO-FB with screw cap 6
25 34 25 Bottles 200 ml PA-FB/W UC with screw cap 6
25 34 31 Bottles 250 ml PE-FB with screw cap 6
25 34 39 Bottles 250 ml PF-FB with screw cap 2
25 34 41 Bottles 250 ml PC-RB with screw cap 6
25 34 43 Bottles 250 ml PP-RB with screw cap 6
25 34 45 Bottles 250 ml PPCO-RB with screw cap 6
25 34 47 Bottles 250 ml PE-RB with screw cap 6
25 34 49 Bottles 250 ml PF-RB with screw cap 2
25 34 81 Bottles 290 ml PC-FB with screw cap 6
25 34 87 Bottles 290 ml PE-FB with screw cap 6
25 35 01 Bottles 500 ml PC-FB with screw cap 6
25 35 12 Bottles 500 ml PP black-FB with screw cap 2
25 35 21 Bottles 500 ml PPCO-FB with screw cap 6
25 35 31 Bottles 500 ml PE-FB with screw cap 6
25 35 51 Bottles 500 ml PPCO-FB with screw cap (for rotor AS 4.500 only) 4
25 35 62 Bottles 1000 ml PC-FB with screw cap 4
25 35 65 Bottles 1000 ml PC-FB with screw cap and support ring 4
25 35 72 Bottles 1000 ml PPCO-FB with screw cap 4
25 35 75 Bottles 1000 ml PPCO-FB with screw cap and support ring 4
25 35 80 Bottles 750 ml PC-FB with screw cap 4
25 35 81 Bottles 750 ml PP-FB with screw cap 4
25 35 90 Bottles 650 ml PC-FB with screw cap 4
25 35 91 Bottles 650 ml PP-FB with screw cap 4
25 45 50 Cap for tubes 14 ml PA + 16 ml PPCO. PC 10
25 45 51 Cap for tubes 14 ml PE + 16 ml PE 10
25 46 00 Cap for tubes (Loop Cap) for tubes 50 ml FL 10
25 46 05 Cap for AOR tubes 10 ml PC. PPCO 10
25 46 06 Cap for AOR tubes 10 ml PE 10
25 46 08 Cap for AOR tubes 10 ml PF 1
25 46 15 Cap for AOR tubes 30 ml PC. PPCO 10
25 46 16 Cap for AOR tubes 30 ml PE 10
25 46 18 Cap for AOR tubes 30 ml PF 1
25 46 25 Cap for AOR tubes 50 ml PC. PPCO 10
25 46 26 Cap for AOR tubes 50 ml PE 10
25 46 28 Cap for AOR tubes 50 ml PF 1
25 46 35 Cap for AOR tubes 80 ml PC. PPCO 10
page 33 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Cat. No. Item Units per pack
25 46 36 Cap for AOR tubes 80 ml PE 10
25 46 38 Cap for AOR tubes 80 ml PF 1
25 46 50 Rubber cap for glass tubes 10
25 46 55 Screw cap for bottles 200 ml 6
25 46 60 Screw cap for bottles 250. 290 . 500. 1000 ml 6
25 46 62 Screw cap for bottles 1000 ml with support ring (black) 1
25 46 63 Screw cap for bottles 250 ml PF 1
25 46 65 Screw cap for bottles 250 ml PA UC 1
25 46 82 Screw cap, aluminum, for UC tubes 94 ml 1
25 46 85 Screw cap, aluminum, for UC tubes 38.5 ml 1
25 46 88 Screw cap, aluminum, for UC tubes 13.5 ml 1
25 46 91 Screw cap, aluminum, for UC tubes 6.5 ml 1
25 46 94 Screw cap, aluminum, for UC tubes 4.4 ml 1
25 49 00 Extractor tool for UC tubes 1
25 50 00 Adapter 50 ml Rotor bore / 4 x 1 ml 2
25 50 05 Adapter 2.2 ml Rotor bore / Micro tubes 0.25-0.4 ml / Pck. with 6 pieces 6
25 50 06 Adapter 2.2 ml Rotor bore / Micro tubes 0.5-0.7 ml / Pck. with 6 pieces 6
25 50 07 Adapter 2.2 ml Rotor bore / Micro tubes 0.2 ml PCR / Pck. with 6 pieces 6
25 50 10 Adapter 50 ml Rotor bore / 2 x 1.5 ml Eppendorf 2
25 50 11 Adapter 50 ml Rotor bore / 2 x 4.5/5 ml 2
25 50 30 Adapter 50 ml Rotor bore / 1 x 10 ml AOR 2
25 50 50 Adapter 50 ml Rotor bore / 1 x 16 ml 2
25 50 61 Adapter 50 ml Rotor bore / 1 x 30 ml AOR 2
25 50 62 Adapter 50 ml Rotorbore Falcon / 1x 30 ml AOR 2
25 50 70 Adapter 16 ml Rotor bore / 1 x 1.5 ml Eppendorf 2
25 50 71 Adapter 14 ml Rotor bore / 1 x 1.5 ml Eppendorf 2
25 50 72 Adapter 16 ml Rotor bore / 1 x 4.5/5 ml 2
25 50 73 Adapter 14 ml Rotor bore / 1 x 4.5/5 ml 2
25 50 90 Adapter 250 ml Rotor bore / 15 x 3 ml glass tubes 2
25 51 00 Adapter 250 ml Rotor bore / 9 x 4.5/5 ml plastic tubes or 5 ml glass tubes 2
25 51 10 Adapter 250 ml Rotor bore / 9 x 10 ml glass tubes (Ø 13 mm) 2
25 51 30 Adapter 250 ml Rotor bore / 5 x 16 ml plastic or 12/15 ml glass tubes (Ø 18 mm) 2
25 51 35 Adapter 250 ml Rotorbore / 5 x 15 ml Falcon 2
25 51 60 Adapter 250 ml Rotor bore / 3 x 30 ml glass tubes 2
25 51 70 Adapter 250 ml Rotor bore / 1 x 100/120 ml (Ø 40 mm) 2
25 51 75 Adapter 250 ml Rotorbore / 1x Falcon 50 ml 2
25 51 81 Adapter (Bottom Pad) 250 ml Rotor bore / 1 x 250/290 ml bottles FB 6
25 51 90 Adapter (Bottom Pad) 250 ml Rotor bore / 1 x 250/290 ml bottles RB 6
25 52 10 Adapter 250 ml Rotor bore / 15 x 1.5 ml Eppendorf 2
25 52 41 Support ring for bottles 500 ml / Closing device for bottles 250. 290. 500 ml 6
25 53 80 Adapter 50 ml Falcon / 1 x 15 ml Falcon 2
25 55 10 Adapter 50 ml Rotor bore / 2 x 3 ml glass tubes 4
25 55 30 Adapter 50 ml Rotor bore / 1 x 10 ml glass tubes 4
25 55 40 Adapter 50 ml Rotor bore / 1 x 10 ml glass tubes with conical bottom 4
25 55 50 Adapter 50 ml Rotor bore / 1 x 12 ml glass tubes 2
25 55 60 Adapter 50 ml Rotor bore / 1 x 30 ml glass tubes 2
25 55 80 Adapter 16 ml Rotor bore / 1 x 3 ml glass tubes 4
25 56 00 Adapter 16 ml Rotor bore / 1 x 10 ml glass tubes (Ø 13 mm) 4
25 56 40 Adapter 14 ml Rotor bore / 1 x 5 ml glass tubes 4
25 58 00 Adapter (Bottom Pad) 50 ml Rotor bore / 1 x 45 ml glass tubes 4
25 58 10 Adapter (Bottom Pad) 250 ml Rotor bore / 1 x 200 ml glass tubes 4
25 58 20 Adapter (Bottom Pad) 16 ml Rotor bore / 1 x 12/15 ml glass tubes (Ø 18 mm) 4
page 34 of 34
Laborgeräte GmbH
Represent for Switzerland HEMOTEC GMBH Ribistrasse 7 CH-4460 Gelterkinden
Tel.: +41 (0) 61 981 66 33 Fax: +41 (0) 61 981 40 26 E-Mail: [email protected]
Internet: www.hemotec.ch
CENTRIFUGE LABWARE
2014-02
All products built by Herolab carry the CE sign. Herolab is certified after DIN EN ISO 9001.2008 and DIN EN ISO 13485.
All prices without MWSt, ex works. – Herolab reserves the right to change technical specifications and prices without prior notice.
Cat. No. Item Units per pack
25 58 53 O-Ring for screw caps of bottles 200 ml / pck. with 3 pieces 3
25 58 55 O-Ring for screw caps of bottles 250. 290. 500. 1000 ml / pck. with 3 pieces 3
25 58 57 O-Ring for screw caps of bottles 250. 290. 500. 1000 ml PF 3
25 58 65 O-Ring for screw caps of bottles 250 ml PA UC / pck. with 3 pieces 3
25 58 81 O-Ring for AOR tubes 10 ml PE. PF / pck. with 3 pieces 3
25 58 83 O-Ring for AOR tubes 30 ml PPCO. PC / pck. with 3 pieces 3
25 58 84 O-Ring for AOR tubes 30 ml PF / pck. with 3 pieces 3
25 58 85 O-Ring for AOR tubes 50 ml PPCO. PC / pck. with 3 pieces 3
25 58 86 O-Ring for AOR tubes 50 ml PF / pck. with 3 pieces 3
25 58 87 O-Ring for AOR tubes 80 ml PPCO. PC / pck. with 3 pieces 3
25 58 88 O-Ring for AOR tubes 80 ml PE / pck. with 3 pieces 3
25 58 89 O-Ring for AOR tubes 80 ml PF / pck. with 3 pieces 3
25 59 00 O-Ring for screw cap. aluminum for UC tubes 94 ml 1
25 59 05 O-Ring for screw cap. aluminum for UC tubes 38.5 ml 1
25 59 10 O-Ring for screw cap. aluminum for UC tubes 13.5 ml 1
25 59 15 O-Ring for screw cap. aluminum for UC tubes 6.5 ml 1
25 59 20 O-Ring for screw cap. aluminum for UC tubes 4.4 ml 1
25 80 20 Extractor tool for tubes 50 ml with FL 1
25 80 30 Extractor tool M6 1
25 80 60 Rotor stand for all rotors with conical bore 1
25 80 70 Cleaning brush for all rotors 50 ml 1
25 80 80 Cleaning brush for all rotors 14/15/16 ml 1
25 80 90 Cleaning brush for all rotors 250/290 ml 1
25 81 20 Extractor tool for bottom support pad 1
25 81 60 Extractor tool M4 1