CELLULAR MOBILE PHONE ANTENNA SUMMARY · Cellular Mobile Phone Network Coverage ... Multiband NEXT...

CELLULAR MOBILE PHONE ANTENNA SUMMARY

ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]

Section 5

Â Vehicle Bull Bar Mount

Â Vehicle Guard, Boot and Mirror Mount

Â Vehicle On-Glass Mount

Â Folding Base Mount

Â Whips, Bases and Cable Sets

Â Magnetic Base

Â Omnidirectional Mast Mount Base Station

Â Yagi Directional Mast Mount Base Station

Â Low Profile, Rugged and Covert

Â 3G, 1920 ─ 2170 MHz

Â All-In-One Mobile Phone, GPS and Wi-Fi

TC1600 MAX-GAINNEXT G or GSM

Vehicle Bull Bar Mount

Frequency


CELLULAR MOBILE PHONE ANTENNAS

Section 5

Updated 18 February 2011

Bandwidth825 – 960 MHz NEXT G or GSM

With 8.1 dBi gain, these TC1600 models offer the maximum gain and reception range practical in a broadband vehicle mounted cellular mobile phone antenna.

Available with either a white or pink fibreglass radome, the antenna stands 2.2 metres tall and, for a vehicle, the Bull Bar is the mounting position recommended. Due to size, mounting to the vehicle guard, boot or mirror is not practical.

TC1600A Â is tuned for the NEXT G network.TC1600D Â is for the GSM network.

Matched internally by a unique transforming printed circuit board, these antennas are ground independent and do not require any metal ground plane to operate effectively.

The antenna is firmly secured into any 12.7 mm (½") minimum diameter hole using the bolt and spring washer provided. If required, the BBM-SS stainless steel bull bar bracket is available to order separately. The heavy duty stainless steel parallel spring dampens vibrations while travelling. 5 metres of RG58 low loss cable side-exits from the chromed brass ferrule. An FME female crimp connector is fitted to the cable.

These mobile phone antennas are identical in appearance to: TCMA675 Â , UHF CB Radio 477 MHz.TC1100 Â , AM/FM Radio Receive.

The antenna top whip only without any barrel spring is available to order separately.

The antenna top may be used to mount in locations other than on a vehicle, or to replace a damaged radome.

Contact our Consultants for further advice.

2.2 metres

Construction

SPECIFICATIONS TC1600A

VSWR

GainMaximum Input Power

Polarisation

E-PlaneH-Plane

Impedance

Tuning

Cellular Mobile Phone Network Coverage

Connector

Mounting

8.1 dBi30 Watts

13O

360O Omnidirectional

50 Ohms

NEXT G825 to 890 MHz

Full band at <1.5:1Factory

Secure into any 12.7 mm (½”) minimum diameter hole using the bolt and spring washer supplied

TC1600D

Factory

30 Watts50 Ohms

13O

Tapered fibreglass radome, chrome plated brass ferrule, brass adaptor, stainless steel parallel spring

Vertical

FME Female crimp connector fitted to the cableHeight 2.2 metresWeight 1.5 kg 1.5 kg

GSM890 to 960 MHz

Full band at <1.5:1

8.1 dBi

Vertical360O Omnidirectional

Recommended Mounting Position

Vehicle bull bar. If required, the BBM-SS stainless steel mounting bracket is available separately.

Cable 5 metres of RG58 Low Loss cable side exits from the chrome plated brass mount ferrule

Radome Colour White

TC1600A-P TC1600D-P

Pink White Pink

SGDB Super GainMultiband NEXT G and GSM

Vehicle Bull Bar Mount

Frequency


CELLULAR MOBILEPHONE ANTENNAS

Section 5

Updated 30 November 2011

Bandwidth825 – 960 MHz

1710 - 2190 MHzNEXT G and GSM

combined

The SGDB antenna can also be mounted to the vehicle guard or boot using the appropriate bracket.

However, clients should first consider the lighter 6.2 dBi SGLDB model specifically designed for this purpose.

The SGDB cellular mobile phone antenna is a popular choice for good reason :

Multiband coverage of 1. both NEXT G and GSM networks combined.Effective performance with 2. 6.2 dBi gain.Ground independent; no metal ground plane is necessary.3. Modest size at 90 cm tall.4. Robust construction ensuring a long service life.5.

The fibreglass radome is available in 3 colours; Black, White or Brown.

Secure the antenna firmly into any bracket with a 12.7 mm (½”) minimum diameter hole using the bolt and washer provided. The typical mounting point for this model is to a vehicle bull bar.

The high quality electro-polished stainless steel barrel spring dampens vibrations while travelling. 5 metres of RG58 low loss cable side exits from the aluminium mount ferrule. An FME female connector is fitted to the cable.

This SGDB antenna is identical in appearance to :SG477 Â 477 MHz UHF CB Radio.SG1100 Â AM/FM Radio Receive.

The SGDB-TPM antenna top only without any barrel spring is available to order separately. This antenna top can be used to mount in locations other than on a vehicle, or to replace a damaged radome.


SPECIFICATIONS SGDB BLACK

NEXT G and GSM combined825 to 960 MHz and 1710 to 2190 MHz

6.2 dBi at 825 to 960 MHz3 dBi at 1710 to 2190 MHz

Gain

Less than 1.6:1 across the full band

30 Watts50 Ohms

Factory

5 metres RG58 low loss stranded cable side exits from the aluminium mount ferrule

FME female fitted to the cable90 cm900 gramsSecure into any bracket with minimum 12.7 mm (½") diameter hole using the bolt and spring washer supplied

VSWR

Maximum Input PowerImpedance

Tuning

Cable

ConnectorHeightWeight

Mounting

ConstructionFibreglass radome, copper radiating elements, aluminium ferrule, electro-polished stainless steel barrel spring

BlackRadome Colour

VerticalPolarisation360O OmnidirectionalH-Plane32OE-Plane

Vehicle bull bar. If required, the BBM-SS stainless steel mounting bracket is available

Recommended Mounting Position

SGDB WHITE SGDB BROWN

White Brown

SGLDB Light DesignMultiband NEXT G and GSM

Vehicle Mount

Frequency



Section 5




combined

An FME female connector is fitted to the cable.

Standing 75 cm tall with 6.2 dBi gain, SGLDB is the ideal light weight multiband antenna solution to cover both the NEXT G and GSM cellular mobile phone networks combined.

Specifically designed by ZCG Scalar for mounting to a vehicle guard, the boot of a sedan or to a truck mirror, no metal ground plane is necessary.

The antenna mounts simply into any bracket with a 16 mm minimum diameter hole and is secured firmly by the nut and washer at the base.

The electro-polished stainless steel barrel spring dampens vibrations while travelling.

5 metres of RG58 low loss cable bottom exits through the spring and mount ferrule. An FME Female connector is fitted to the cable.

The fibreglass radome is available in 3 colour; Black, White or Brown.

This SGLDB mobile phone antenna is identical in appearance to :

SGL477 Â , UHF CB Radio 477 MHz.SGL1100 Â , AM/FM Radio Receive.

This SGLDB antenna can also be mounted to a vehicle bull bar. However, clients should first consider the TC1600 and SGDB models specifically designed for a bull bar.

SPECIFICATIONS SGLDB BLACK


VSWR

Maximum PowerImpedance

Tuning

Polarisation

Cable


Mounting

Gain

Radome Colour

Construction

Recommended Mounting Positions

NEXT G and GSM combined825 to 960 MHz and 1710 to 2190 MHzLess than 1.6:1 across the full band

30 Watts50 Ohms

Factory

Vertical

5 metres RG58 low loss cable bottom exits through spring and mount ferrule

FME female fitted to the cable75 cm650 grams

Secure into any 16 mm minimum diameter hole using the nut and washer in the base

BlackFibreglass radome, copper radiating elements, aluminium ferrule,electro-polished stainless steel spring

Vehicle guard, vehicle boot or truck mirror. A mounting bracket is available separately.

SGLDB WHITE SGLDB BROWN

White Brown


GIDM90T SeriesNEXT G or GSMVehicle Mount

Frequency



Section 5



GIDM90T ground independent cellular mobile phone antennas are a modest size and deliver excellent perfomance with 5.1 dBi gain.

Just 45 cm tall, select either the NEXT G or GSM model. Both are a rugged design with detachable stainless steel black powder coated whip and mount simply into any 10 mm diameter hole using the nut and spring washer at the base.

Typically the antenna is mounted to a vehicle guard, boot or truck mirror using the appropriate bracket. However they can also be mounted in any fixed location, not just on a vehicle.

No metal ground plane is necessary for the antenna to operate effectively.

4.5 metres of RG58 low loss cable bottom exits through the base.


The 1570 stainless steel spring is available separately as another mounting option for the GIDM90T cellular mobile phone antennas.This medium duty 50 mm spring screws on to the antenna base and will dampen vehicle vibrations while travelling.The coaxial cable threads through the the centre of the spring and drilled mounting bolt.Replacement stainless steel black powder coated whips are also available.

Part 1570Optional stainless steel spring

to suit GIDM90T antennas


SPECIFICATIONS GIDM90T(NextG)


VSWR


Tuning

PolarisationCable

Connector

HeightWeight

Mounting

5.1 dBiGain

< 1.6:1 full band

5 Watts50 Ohms

Factory

Vertical4.5 metres RG58 low loss bottom exits

FME female fitted(Other connectors available)

45 cm350 grams

Secure into any bracket with minimum 10 mm diameter hole using the threaded stud and nut assembly at the base

Colour Black


Vehicle guard, boot, truck mirror or any other fixed location. Mounting brackets available.

GIDM90T(GSM)

GSM890 to 960 MHz

5.1 dBi5 Watts50 Ohms

Factory

Vertical

40 cm350 gramsBlack

< 1.6:1 full band

GIDM-DBMultiband NEXT G and GSM

Frequency



Section 5


Bandwidth825 – 960 MHz NEXT G and GSM combined

Key features of this model GIDM-DB antenna are :

Multiband coverage of Â both NEXT G and GSM cellular mobile phone networks combined.

Small size at just 27 cm tall. Â

2.1 dBi gain. Â

Ground independent. Â

Easily mounted to a vehicle guard, boot, truck mirror or any Âfixed location using the appropriate bracket.

The antenna is firmly secured into any 10 mm hole using the threaded stud and nut assembly at the base.

5 metres of RG58 low loss cable bottom exits through the base. The cable may be cut shorter if desired.

An FME Female connector is supplied.

After securing the antenna in position and trimming the cable to the required length,fit the FME female crimp connector supplied.


SPECIFICATIONS GIDM-DB

NEXT G and GSM combined825 – 960 MHz

VSWR


Tuning

PolarisationCableConnectorHeightWeight

Mounting

2.1 dBiGain

< 1.6:1 across full band

5 Watts50 Ohms

Factory

Vertical5 metres RG58 Low LossFME female supplied, not fitted27 cm280 grams

Secure into any 10 mm hole using the threaded stud and nut assembly

Colour Black


Vehicle guard, boot, truck mirror or other fixed location. A mounting bracket is available separately.

OG835Multiband NEXT G and GSM

Vehicle On-Glass Mount

Frequency



Section 5


Bandwidth825 – 960 MHz NEXT G and GSM combined

Installation Tips :

It is important to avoid mounting this on-glass antenna anywhere near heated demister elements or on any area of glass which contains metal flakes.When the mount location has been selected, typically high up on the rear window, wash the glass area inside and out with a detergent solution and wipe dry. Then use the alcohol wipe provided to further remove any film from the window area where the external antenna base and internal coupling box will be mounted.

The modern adhesive pads used have immense gripping strength, so much so that great care must be taken to locate the antenna base and coupling box exactly in the desired position at first attempt.

Attach the 4 metre RG58 low loss cable set to the internal coupling box with FME connector. Route the cable carefully to your car kit. The cable can be located in the head lining or under the carpet as desired. Ensure that the cable is not stretched excessively and there are no sharp kinks. If using any cable ties, do not pull so tight as to crush the cable. A damaged feeder cable is a cause of high VSWR and reduced performance.

If the FME Female connector fitted to the cable does not suit your car kit, then carefully fit the alternative Mini-UHF Male crimp connector supplied in it’s place, or other connector to suit RG58 cable.

The whip must be vertical for best performance.

Small and unobtrusive, an on-glass cellular mobile phone antenna is a popular alternative to other bracket mounted antennas.

Model OG835 is factory tuned to cover both the NEXT G and GSM cellular mobile phone networks combined.

With 5.1 dBi gain this on-glass antenna will improve your mobile phone reception range while travelling.

The Installation Kit Includes :

Alcohol wipe to clean and prepare glass inside and Âout.

Black removeable whip standing 30 cm tall. Â

External pivoting whip base with adhesive pad. Â

Internal coupling box with Â FME Male connector and adhesive pad.

4 metres of RG58 low loss coaxial cable with ÂFME Female connectors fitted each end.

Mini-UHF Male Â crimp connector also supplied.


SPECIFICATIONS OG835

Both NEXT G and GSM combined, 825–960 MHz

VSWR


Tuning

PolarisationWhip HeightKit Weight

Mounting

5.1 dBiGain

< 2:1 across full band

5 Watts50 Ohms

Factory

Vertical30 cm150 grams

On-Glass using the Adhesive Pads supplied

Colour Black

FME Female connectors are fittedto each end of the 4 metre

RG58 low loss cable supplied

A Mini-UHF Male connector is also supplied

OGI-EPH401 On-Glass Inside Vehicle Multiband NEXT G, GSM and 3G

Mobile Phone AntennaCELLULAR MOBILEPHONE ANTENNAS

Section 5

Frequency Bandwidth824 – 960 MHz

1710 – 2170 MHzNEXT G, GSM and 3G

combined


Updated 23 June 2011

This on-glass antenna sticks to the inside of a vehicle windscreen and will improve cellular mobile phone reception and transmission range while travelling.

The OGI-EPH401 antenna offers these significant features :

Multiband coverage Â of all the cellular mobile phone networks operating around Australia; NEXT G, GSM and 3G.

Small and inconspicuous Â .

Simple installation Â , no bracket, no holes, no screws. Just peel and press the adhesive single side tape to the inside of the screen, route the cable and connect to the mobile phone car kit.

The antenna is secure inside your vehicle Â . No external parts means the possibility of damage and vandalism are minimised. The car wash is no longer a worry !

SPECIFICATIONS

NEXT G, GSM and 3G networks combined

1.5 dBiBetter than 1.5:1

50 OhmsFactory

Omnidirectional

106.5 mm long x 10.6 mm wide x 4.5 mm high45 grams including cable

824 – 960 MHz and 1710 – 2170 MHz800 / 900 / 1800 / 1900 / 2100 MHz

3 metres standardFakra Type D (Plum / Maroon) connector fitted

Half wave dipole

Single side tape


VSWR

ImpedanceTuning

Polarisation

DimensionsWeight

Gain

Frequency Range

CableConnector

Wave

Overmold HousingMounting

ABS Black

Operating Temperature -40OC to +80OCStorage Temperature -40OC to +80OC

OGI-EPH401

Return Loss, 800 MHz to 2 GHz

OGI-08-4Multiband NEXT G, GSM and 3GInside Vehicle On-Glass Mount

Frequency



Section 5


Bandwidth800 – 2,100 MHz NEXT G, GSM, 3G combined

Installation Tips :

It is important to avoid mounting this on-glass antenna anywhere near heated demister elements or on any area of glass which contains metal flakes.The antenna may be located inside a vehicle on either the front or rear screen. Once the mount location has been selected, wash the glass area inside with a detergent solution and wipe dry thoroughly. Peel the adhesive pad and press onto the glass firmly. You must be careful to locate the antenna exactly in the desired position at first attempt.Route the cable carefully to the car kit. The cable can be located in the head lining or under the carpet as desired. Ensure that the cable is not stretched excessively and there are no sharp kinks. If using any cable ties, do not pull so tight as to crush the cable. A damaged feeder cable is a cause of high VSWR and reduced performance.An SMA Male connector is fitted to the cable. However, if your car kit has an FME Male connector, then fit the FME Female to SMA Female Adaptor provided.

This on-glass antenna model OGI-08-4 sticks to the inside of a vehicle windscreen and will improve cellular mobile phone reception and transmission range while travelling.

The antenna offers these significant features :Multiband coverage Â of all the cellular mobile phone networks operating around Australia; NEXT G, GSM and 3G.

Effective performance Â with 2.1 dBi gain, comparable to an external on-glass mount whip.

Small and inconspicuous Â .

Simple installation Â , no bracket, no holes, no screws. Just peel and press the adhesive pad to the inside of the screen, route the cable and connect to the car kit.

The antenna is secure inside your vehicle Â . No external parts means the possibility of damage and vandalism are minimised and the car wash no longer a worry !

21 mm

115 mm

Just 7 mm thick

Peel and press the adhesive pad onto glass

An SMA Male connector is fitted to the 3 metre RG174 cable

An FME Female to SMA Female Adaptor is also provided


SPECIFICATIONS OGI-08-4

NEXT G, GSM and 3G

VSWR


Tuning

Polarisation

Dimensions

Weight

Mounting

2.1 dBiGain


5 Watts50 Ohms

Factory

Vertical

115 mm long, 21 mm wide, 7 mm thick

5 grams

Adheres to glass inside a vehicle, either the front or rear screen

Operating Temperature -20OC to +60OC

Frequencies 800/900/1800/1900/2100 MHz

CableConnector

3 metres of RG174SMA Male fitted to the cable

Colour Black

Adaptor Supplied FME Female to SMA Female

MADBMultiband NEXT G and GSM

with Folding Base

Frequency



Section 5




combined

The MADB cellular mobile phone antenna with folding base provides multiband coverage of both NEXT G and GSM networks combined with an effective 6.2 dBi gain. No metal ground plane is necessary.

Standing 90 cm tall, the MM1 folding base supplied as standard is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt.

This versatility makes the MADB model a perfect choice for mounting to boats, caravans, a trailer, outside on the facia board of a building or any flat surface at any angle desired using four screws or bolts. The antenna can be folded down flat while not in use.

5 metres of RG58 low loss stranded cable side exits from the mount ferrule. The FME female connector fitted to the cable is rated for up to 30 watts input power.

The fibreglass radome is available in 2 colours; Black or White. Specify your preference when ordering.

This MADB antenna is identical in appearance to the MA477 model for 477 MHz UHF CB radio and MA1100 for AM/FM radio receive.

For those who prefer the ultimate in quality, durability and strength, the antenna is also available with the MM2 folding base which is constructed entirely from stainless steel. The order code is MADBSS.

The MM1 folding base supplied as standard is constructed from toughened plastic.

For those who prefer the ultimate in quality, durability and strength, the MM2 folding base is constructed entirely from stainless steel. This MM2 base is supplied with the MADBSS model.


SPECIFICATIONS MADB


Max Input PowerImpedance

Tuning

Polarisation

Height (inc mount)Weight (inc mount)

Gain

Construction


30 Watts50 Ohms

Factory

Vertical

90 cm0.8 kg

Fibreglass radome, copper radiating elements, aluminium ferrule, delrin adaptor for base

VSWR Less than 1.6:1 across the full band

H-Plane 360O Omnidirectional

Connector An FME female connector is fitted to the cable

Cable 5 metres of RG58 low loss stranded cable side exits from the aluminium ferrule

Radome Colour Specify either a White, Black or Brown radome colour when ordering

Folding Base Supplied

Secure the folding base to any flat surface at any angle using 4 screws or boltsMounting

MM1toughened plastic

MM2stainless steel

MADBSS

1.55 kg90 cm

Factory

30 Watts50 OhmsVertical360O Omnidirectional


NEXT G and GSMWhips, Bases and Cable Sets

Frequency



Section 5



For reception of a cellular mobile phone network, a phased whip may be fitted to a base and then mounted in a variety of locations, either fixed or mobile. The various options available appear below.

M90T (Next G) whipFor the Â NEXT G network

825 ─ 890 MHz full band Â

5.1 dBi gain Â

30 cm tall Â

Stainless steel, open phasing coil, Âpowder coated black

6 mm thread in mount ferrule Â

M90T (GSM) whipFor the Â GSM network

890 ─ 960 MHz full band Â

5.1 dBi gain Â

25 cm tall Â

Stainless steel, open phasing coil, Âpowder coated black

6 mm thread in mount ferrule Â

XB mounting baseSuit either Â M90T (Next G) or M90T (GSM) whip

6 mm thread Â

No cable, no connector Â(available separately)

XB4.7 mounting base and cable set

Suit either Â M90T (Next G) or M90T (GSM) whip

6 mm thread Â

4.7 metres of RG58 low loss solid core Âcable fitted to the base (may be cut shorter if desired)

No connector Â(specify and order separately)

MGB-XB magnetic mounting base and cable set

Suit either Â M90T (Next G) or M90T (GSM) whip

6 mm thread Â

Magnetic base 10.5 cm diameter Â

4.7 metres of RG58 low loss solid core Âcable fitted to the base (may be cut shorter if desired)

No connector Â(specify and order separately)

The MGB-XB magnetic antenna base is manufactured from steel with an attractive polished black powder coat finish. 10.5 cm in diameter, the strong magnet will positively secure the antenna base to any flat metal surface with no slippage. Most typically, this base is used on the roof of a vehicle and removed when not required. The PVC matted pad on the bottom will prevent scratching the surface to which the base is applied.

MGB-XB

XB4.7

XB

M90T (Next G) M90T (GSM)

The perfect choice for hire cars or when driving different vehicles in a fleet

MAGM90TWireless Internet Modem Antennas

with Magnetic BaseFrequency



Section 5

Updated 12 January 2012

GainNEXT G : 825 – 890 MHzor GSM : 890 – 960 MHz 5 dBi

The MAGM90T series portable indoor antennas with magnetic base deliver 5 dBi gain and will enhance the reception of your wireless internet modem. Alternatively, they can also be connected to a cellular mobile phone.

Model “ Â MAGM90T800” is for the NEXT G network.

Model “ Â MAGM90T900” covers the GSM network frequency.

Ideal for indoor use, the magnetic base adheres to any flat metal surface. Easy to set-up, easy to remove and the detachable whip makes the antenna easy to store when not required.

These compact portable antennas stand just 32.5 cm tall and are factory tuned for better than 1.5:1 VSWR across the full band.

The 4 cm diameter magnetic base is manufactured from moulded plastic with nickel plated brass fittings. An FME Male connector is housed inside the base. The black powder coated detachable stainless steel whip fits onto the 6 mm – 26 TPI thread.

The antenna is supplied with a 5 metre RG58 low loss solid core cable set with connectors fitted.

The Â FME female connector attaches into the antenna base.

The Â SMA male connector attaches into the modem or cellular mobile phone.

Other connector options can be provided by special order.

Black powder coated detachable stainless steel whip

5 metre RG58 low loss solid core assembled cable set

32.5 cm tall

Magnetic base with FME male connector

FME female fitted

SMA male fitted

Easy to set-up

Easy to store

SPECIFICATIONS MAGM90T800


5 dBi

Better than 1.5:1 across the full band

5 Watts50 Ohms

Factory

Vertical

5 metres RG58 low loss solid core coaxial cable with FME Female and SMA Male connectors fitted

FME Male inside base

32.5 cm60 grams

4 cm diameter Magnetic Base adheresto any flat metal surface


VSWR


Tuning

Polarisation

Cable Set Supplied

Connector

HeightWeight

Mounting

Nominal Gain

Construction

Magnetic base, moulded black plastic with nickel plated brass fittings, black powder coated stainless steel whip,6 mm – 26 TPI thread

MAGM90T900

GSM890 to 960 MHz

Reception indoors will vary depending upon the antenna location. Best results will be obtained by positioning the antenna near to the window or outer wall, rather than in the centre of the building.

MAG-CDMANEXT G Antenna

with Magnetic Base

Frequency



Section 5


Bandwidth825 – 890 MHz NEXT G

SPECIFICATIONS MAG-CDMA

NEXT G, 825 ─ 890 MHz

3 dBi


5 Watts50 Ohms

Factory

Vertical

Can be assembled according to your requirements. Order separately.

FME Male inside base13.5 cm60 grams

Magnetic Base 4 cm diameteronto any flat metal surface


VSWR


Tuning

Polarisation

Cable Set(not supplied)


Mounting

Nominal Gain

Construction Moulded black plastic with nickel plated brass fittings and magnetic base

Manufactured from moulded plastic with nickel plated brass fittings, the MAG-CDMA antenna may be used to improve reception of the NEXT G cellular mobile phone network operating in the frequency range 825 to 890 MHz.

This compact portable model delivers 3 dBi nominal gain. An FME male connector is located inside the base and the magnetic base mounts simply onto any metal surface.

The antenna is easy to fit, easy to remove and at just 13.5 cm tall, easy to store when not required.

A cable set can be assembled to meet your specific requirements.

CM Series MAX-GAINNEXT G or GSM

Mast Mount Antennas

Frequency



Section 5



With 8.1 dBi gain, these mast mount models offer the maximum gain and reception range practical in a broadband omnidirectional cellular mobile phone base station antenna.

The white fibreglass radome and stainless steel mount tube stands 2.4 metres tall. The antenna is matched internally by a unique transforming printed circuit board.

The N-Female connector located at the base of the mount tube is rated for up to 20 watts input power.

CM1600AM Â is factory tuned to cover the NEXT G network.

CMG1600AM Â is for the GSM network.

All components used are of the highest quality to ensure long term survival in the harshest weather conditions and environments. These antennas will deliver reliable performance for many years.

Mounting clamps, feeder cable, connectors, cable ties and tape are available separately to complete the installation.

EB1SSstainless steel parallel mast

clamps

Construction

SPECIFICATIONS


Single piece white fibreglass tapered radome, transforming printed circuit board, stainless steel mount tube


CM1600AM

GainMax Input Power

8.1 dBi

Impedance

Polarisation Vertical

20 Watts

Height 2.4 metresWeight 0.7 kg

MAST Mounting Clamps (not supplied)

2 x EB1SS stainless steel parallel clamps recommended.Suit round mast between 20 mm and 50 mm in diameter.

Mount Tube 420 mm long x 20 mm diameter

CMG1600AM

8.1 dBi20 Watts

Tuning Factory

Vertical

0.7 kg

FactoryVSWR -10dB

50 Ohms 50 OhmsDC Grounded Yes Yes

H-Plane 360O Omnidirectional 360O OmnidirectionalConnector N-Female located at base of mount tube

2.4 metres

Blue Cap Red Cap

GSM890 to 960 MHz

E-Plane 13O 13O

-10dB

SGDB-TPMMultiband NEXT G and GSM

Antenna Top



Section 5

Updated 25 July 2012

Frequency Bandwidth825 – 960 MHz

1710 – 2190 MHzNEXT G and GSM

combined

At some remote locations or inside a building, cellular mobile phone reception can often be poor. For applications where the cellular device being used can be connected to an external antenna, then our popular SGDB Multiband NEXT G and GSM antenna can be mounted outdoors at your home or office to improve reception.

Order the SGDB-TPM antenna top alone, without the mobile barrel spring. Key features are : Â Multiband coverage of both NEXT G and GSM networks combined. Â Modest size at 80 cm tall with an effective 6.2 dBi gain. Â Omnidirectional radiation pattern. Â Completely ground independent, mount anywhere, no metal groundplane is necessary. Â Rugged fibreglass radome available in Black, White or Brown.

5 metres of RG58 low loss solid core feeder cable side exits from the aluminium mount ferrule. An FME Female connector is fitted to the cable for easy installation. Other connector options are available, or an adaptor as you may require.

The stud, nut and washer at the antenna base permits these versatile mounting options :1. Simply secure the antenna into any 12.7 mm (½”) minimum diameter hole, route the

cable and connect to your mobile phone.2. Fit an “L” bracket, such as our stainless steel model “GM1”, to any vertical panel or fascia

board. Insert the antenna, fit the washer, tighten the nut, route the feeder cable and connect to your mobile phone.

3. Order our model “4266” threaded aluminium mast mount adaptor, screw in the antenna and secure to a mast or hockey stick bracket with the “UB3SS” stainless steel parallel clamp. Alternatively, use hose clamps.

GM1 4266

UB3SS

Optional Mounting Accessories


SPECIFICATIONS SGDB-TPM BLACK



Gain

Less than 1.6:1 across the full band

30 Watts50 Ohms

Factory

5 metres RG58 low loss stranded cable side exits from the aluminium mount ferrule

FME female fitted (others options available)80 cm700 gramsSecure into any 12.7 mm (½”) min diameter hole

VSWR

Maximum Input PowerImpedance

Tuning

Cable

ConnectorHeightWeightMounting

Construction Fibreglass radome, copper radiating elements, aluminium ferrule, stud, nut and washer

BlackRadome Colour

VerticalPolarisation360O OmnidirectionalH-Plane32OE-Plane

SGDB-TPM WHITE SGDB-TPM BROWN

White Brown

1. GM1 : Stainless steel “L” bracket.2. 4266 : Aluminium mast mount adaptor, 150 mm x 25 mm.3. UB3SS : Stainless steel parallel clamp, or use hose clamps.

Optional MountingAccessories

An FME Female connector is fitted to the cable. Other connector options, or an adaptor, are available as you require.

Yagi Y800 SeriesNEXT G or GSM Directional Mast Mount

Base Station Antennas

Frequency



Section 5



For directional high gain reception of a cellular mobile phone network, these Yagi mast mount antennas offer an effective solution.

Constructed from either aluminium or stainless steel, the Yagi Y800 Series consists of 6, 9 and 15 element models varying from 11.1 dBi up to 16.1 dBi forward gain.

All models have a short 250 mm RG59 cable tail terminated with an N-Female connector rated for up to 50 watts input power.

For the Â NEXT G network, order models Y806A, Y809A or Y815A.

For the Â GSM network, select either Y806C, Y809C or Y815C.

Add the letter SS to the order code for stainless steel models.

The A48 and S48 clamps will mount a 25 mm square boom Yagi at right-angles to a round mast between 30 mm and 50 mm in diameter.

Order a clamp separately.

A mast mounting clamp, feeder cable, connectors and other accessories are all available separately to complete the Yagi antenna installation. For the 15 element Y815 model, a single strut kit is recommended to properly support the long boom.

Yagi model Y809A mounted vertical for NEXT G cellular mobile phone network reception

Construction

SPECIFICATIONS Y806

11.1 dBi(=9 dBd)

50 Watts

46O

51O

50 Ohms

Y806A820 to 880 MHz

Full Band-15 dB, <1.5:1Factory

0.035 m2

4.5 kg

A48 x 1 for Aluminium model YagiS48 x 1 for Stainless Steel model Yagi

Y809 Y815

Y809A820 to 880 MHz

Y806C900 to 960 MHz

Y809C900 to 960 MHz

Full Band-15 dB, <1.5:1

6 9Factory

13.6 dBi(=11.5 dBd)

50 Watts50 Ohms34O

42O

17.8 dB 15 dB

Aluminium, or add letters SS to the code for Stainless Steel

Mount the Yagi Vertical for mobile phone network reception

All models have a 250 mm RG59 cable tailAll models are terminated with an N-Female connector

Y815A820 to 880 MHz

Y815C900 to 960 MHz

Full Band-15 dB, <1.5:1

15Factory

16.1 dBi(=14 dBd)

50 Watts50 Ohms28O

30O

15 dB

0.6 metre 0.97 metre 1.85 metres210 mm 210 mm 210 mm0.5 kg 0.7 kg 1.0 kg

0.054 m2 0.075 m2

6.5 kg 9.5 kg

BandwidthReturn Loss, VSWRTuning

For NEXT G network coverage

For GSM network coverage

Number Of Elements

Nominal Gain

Maximum Input PowerPolarisation

E-Plane at 3 dBH-Plane at 3 dB

Impedance

Cable TailConnector

Projected AreaWind Load at 160 kph

Mast Mounting Clamp Recommended

Front-to-Back Ratio

Boom LengthLongest ElementWeight in Aluminium

Strut Kit Recommended Not required Not required YS1-48

1.2 kg 1.5 kg 2.6 kgWeight in Stainless Steel

Yagi Y20093G Directional Mast Mount

Base Station Antenna

Frequency



Section 5


Bandwidth1900 – 2100 MHz 3G Network

The Yagi model Y2009 mast mount base station antenna will provide directional coverage of the 3G cellular mobile phone network operating in the frequency range 1,900 to 2,170 MHz.

Constructed from brass and aluminium, this 9 element Yagi delivers 11.3 dBi forward gain. The ultra violet resistant PVC radome protects the internals.

The short RG58 low loss cable tail is terminated with an N-Female connector rated for up to 25 watts input power.

U-bolts are supplied for mounting to a mast up to 50 mm in diameter.

Mount the Yagi vertical for 3G network reception.

Feeder cable, connectors and fittings are all available separately to complete the installation.

For higher gain and power, this Yagi may be mounted in a stack array formation.

When mounted vertical for the 3G network, the Yagi’s should be spaced 150 mm apart.

Construction

SPECIFICATIONS Y2009

BandwidthReturn Loss, VSWR


Brass and aluminium internals enclosed inside an ultra violet resistant white PVC radome. (A black radome is available.)

U-Bolts are supplied for mounting to a round mast up to 50 mm in diameter

GainMaximum Input Power

PolarisationE-PlaneH-Plane

Impedance

Tuning

Cable TailDC Grounding

Connector

Projected AreaWind Load at 160 kph

Length

Weight

Mounting

Width

Number of Elements

Front-to-Back Ratio

11.3 dBi25 Watts

Mount the Yagi Vertical for 3G Network43O

36O

50 Ohms

Yes

3G, 1900 to 2170 MHz

Full BandBetter than -15 dB, less than 1.5:1Factory

RG58 Low LossN-Female fitted

0.015 m2

1.82 kg

1.5 kg

300 mm80 mm

9

-20 dB

CT800 and CT900NEXT G or GSM

Low Profile, Rugged and Covert

Frequency



Section 5

Updated 1 August 2011


If you require a cellular mobile phone antenna which is small, inconspicuous and virtually indestructible, then model CT800 for the NEXT G network or CT900 for GSM will be your solution.

These low profile, covert and rugged cellular mobile phone antennas are an ideal choice in situations where traditional whip antennas would be vulnerable to damage or vandalism.

Constructed from aluminium and delrin with a rubber mounting gasket, the antenna measures just 150 mm long, 32 mm wide and 32 mm high. It mounts to any flat metal surface by drilling three holes; two for bolts and one larger for the N-Female connector.

The metal surface acts as a ground plane and, if around 1 metre square, the antenna will produce a near omnidirectional radiation pattern with 2.1 dBi gain.

The N-Female connector protrudes through the metal surface so as your feeder cable connected from underneath is concealed and protected from damage. The thick rubber gasket provides a waterproof seal.

Typical applications suited for these low profile antennas include :

Trains 9Buses 9Forklifts 9Tractors 9Forestry Vehicles 9Logging Trucks 9

Police 9Ambulance 9Fire Brigade 9Emergency Services 9Security Services 9

The E-Plane above shows an elevated radiation angle like that of a traditional 1/4 wave whip.

The H-Plane is near omnidirectional but has reduced signal strength at the rear, typical of this low profile design.

SPECIFICATIONS CT800 CT900


2.1 dBi

< 1.6:1 full band

5 Watts50 Ohms

Factory

Vertical

N-Female

170 grams

Drill 3 holes in metal ground plane surface.2 holes for bolts, 1 larger for N-Female connector.N-Female protrudes through ground plane.Low loss feeder cable connects from underneath.

GSM890 to 960 MHz

2.1 dBi

< 1.6:1 full band

5 Watts50 Ohms

Factory

Vertical

170 grams

Aluminium and delrin with rubber sealing gasket

Same as a normal 1/4 wave whipNear 360O omnidirectional


VSWR


Tuning

Polarisation

Connector

Weight

Mounting

Nominal Gain

Construction

E-PlaneH-Plane

Dimensions 150 mm long x 32 mm wide x 32 mm highN-Female

SGL20003G Super Gain Light Design

Frequency



Section 5


Bandwidth1920 – 2170 MHz 3G Network

This model SGL2000 antenna is factory tuned for the 3G cellular mobile phone network operating in the frequency range 1920 to 2170 MHz. With 6.2 dBi gain, the antenna will deliver consistent and dependable results with maximum efficiency, particularly where signal strength is marginal.

The stainless steel spring and fibreglass radome stands 48 cm tall. The antenna mounts into any 16 mm hole and is secured firmly by the threaded stud and nut assembly at the base.

A range of brackets are available to suit various mounting positions such as your vehicle bull bar, guard, boot or truck mirror. The antenna can also be mounted in locations other than on a vehicle. No metal ground plane is necessary for the antenna to operate effectively.

5 metres of RG58 low loss cable bottom exits through the base and may be cut shorter if required. An FME female crimp connector is supplied.

The fibreglass radome is available in either Black or White. Specify your preference when ordering. A Brown radome can be supplied upon request.

After securing the antenna in position and trimming the cable to the required length,fit the FME female crimp connector supplied.

The SGL2000 antenna for the 3G network is 48 cm tall and delivers 6.2 dBi gain

Secure the antenna firmly into any 16 mm hole using the threaded stud and nut assembly

SPECIFICATIONS SGL2000

3G, 1920 ─ 2170 MHz

6.2 dBi

Less than 1.6:1 across full band

30 Watts50 Ohms

Factory

Vertical

5 metres RG58 Low Loss cable bottom exits through spring and mount ferrule

FME female crimp supplied, not fitted48 cm600 grams

Secure into any 16 mm hole using the the threaded stud and nut assembly.

Specify either a Black or White radome colour when ordering(Brown available, but built to order)

Fibreglass radome, copper radiating elements, aluminium ferrule,electro-polished stainless steel spring


VSWR

PowerImpedance

Tuning

Polarisation

Cable


Mounting

Gain

Radome Colours

Construction

RecommendedMounting Positions

Vehicle bull bar, guard, boot or truck mirror. A mounting bracket is available separately.

ALL-IN-ONE MultibandNEXT G, GSM, 3G Cellular Mobile Phone,

GPS and Wi-Fi Antenna

Frequency



Section 5

Updated 2 July 2012

Bandwidth804 MHz – 2.48 GHz See Page 2– Page 1 of 2 –

This single model GCRFA antenna will provide reception for ALL of these applications :

9 NEXT G cellular mobile phone network. 9 GSM cellular mobile phone network. 9 3G cellular mobile phone network. 9 GPS global positioning system, 1575.42 MHz. 9 Wi-Fi, 2.4 GHz.

100 mm in diameter, this compact antenna may be secured through a 20 mm hole to any flat surface or bracket using the 28 mm long bottom thread and screw nut.

Typical mounting positions are to a vehicle or in a fixed location on a building.

The 5 metre cables bottom exit through the base and are terminated with SMA Male connectors. Each lead is labelled.

The alternative model GCT provides both Mobile Phone and GPS reception, but not Wi-Fi.

Detailed specifications for the GCRFA and GCT antennas appear on the following page. SMA Male connectors fitted. Each lead is labelled.

GCTMobile Phone and GPS(not Wi-Fi)

GCRFAMobile Phone, GPS and Wi-Fi

ALL-IN-ONE MultibandNEXT G, GSM, 3G Cellular Mobile Phone,

GPS and Wi-Fi Antenna

Frequency



Section 5

Updated 2 July 2012

Bandwidth804 MHz – 2.48 GHz See Page 2– Page 2 of 2 –

Construction

3 x SMA Male fitted 2 x SMA Male fitted

3 x 5 metres of RG174/U1 x 5 metres of RG174/U1 x 5 metres of RG58/AU

ABS Acrylonitrile Butadiene Styrene, PC polycarbonate, Cream in colour

Connectors

Coaxial Cable

DiameterRadome Height

Weight

Mounting

100 mm39 mm

280 grams

Secure to any flat surface or bracket through 20 mm hole using the28 mm long bottom thread and screw nut

Cellular Mobile Phone Antenna : GCRFA and GCT

Frequency Coverage

Tuning and VSWR

Bandwidth

Polarisation

NEXT G, GSM and 3G networks combined804 ─ 960 MHz, 1710 ─ 1880 MHz, 1850 ─ 1990 MHz, 1920 ─ 2170 MHzFactory tuned to less than 2:1 across each specified frequency range

20 MHz minimum at -10 dB

Right Hand Circular4 dBic minimum (7 cm x 7 cm ground plane)Peak Gain

2.4 – 2.4835 GHz

360O Omnidirectional50 Ohms

25 WattsPattern

Impedance

Maximum PowerGPS Active Patch Antenna : GCRFA and GCT

Frequency Coverage 1575.42 MHz ± 3 MHzTuning and VSWR Factory tuned to 1.5:1 maximum

Axial Ratio 3 dB Typical50 OhmsImpedance

Amplifier ModuleType AType B

Amplifier Gain, no cable

27 dB typical1.4 dB typicalNoise Figure

1.4 dB typical

Output VSWR

2.0 maximum

DC Voltage3.0 V to 5.5 V2.7 V to 6.0 V

DC Current22 ± 5 mA

8.5 ± 4.5 mA

Wi-Fi Antenna : GCRFA (not supported by GCT)Frequency Coverage

Tuning and VSWR Factory tuned to less than 2:1 across the specified frequency range50 OhmsImpedance360O OmnidirectionalPattern25 WattsMaximum Power

Mechanical Specifications : GCRFA and GCT

Cable and Connectors : GCRFA GCT

ZAU seriesMultiband GPS low noise

NEXT G and GSM mobile phone antenna

Frequency



Section 5

Updated 15 July 2012

Bandwidth824 – 1990 MHz See Below

For both AVL Automatic Vehicle Location systems and cellular mobile phone, the ZAU series deliver a highly sensitive multiband mobile antenna solution ideal for fleet management.

9 GPS global positioning system 1575.42 MHz with cutting edge low noise amplifier.

9 NEXT G cellular mobile phone network.

9 GSM cellular mobile phone network.

64.5 mm in diameter, this small, low profile, covert, waterproof and rugged antenna mounts into any 13 mm minimum diameter hole.

Typical mount positions are to a vehicle roof, bull bar, the rear boot lid or inside the cabin on the dashboard.

The small size means that mounting to a truck mirror is also possible.

The RG174 feeder cables bottom exit through the base and are terminated with SMA Male and FME Female connectors for easy connection to GPS and mobile phone devices.

SPECIFICATIONS GPS Antenna

27 dB typicalRight-Hand Circular

2 metres RG174bottom exits

SMA Male fitted

64.5 mm diameter x 14 mm high

1575.42 MHz

High performance GPS patch antenna with cutting-edge low noise amplifier

Polarisation

Cable

Connector

Dimensions

Mounting

Gain

Frequency

Features

RecommendedMounting Positions

Vehicle roof, bull bar, the rear boot lid, inside the cabin on the dashboard or to a truck mirror

NEXT G and GSM Antenna

Multiband NEXT G and GSM cellular mobile phone network coverage

824 – 960 MHz and1710 – 1990 MHz

1.0 dBi--

1.8 maximumNoise Figure --20 db min @ F0 ± 50 MHzAttenuation --

Bandwidth 10 MHz

72 MHz for 824 – 896 MHz80 MHz for 880 – 960 MHz170 MHz for 1710 – 1880 MHz140 MHz for 1850 – 1990 MHz

VSWR Less than 1.5:1 Less than 1.5:1Impedance 50 Ohms 50 Ohms

Power Supply Power Consumption2.5 – 5.5 Volts DC / 13 mA

Power Handling Capacity10 Watts

FME Female fittedOperating Temp -40OC to +85OC -40OC to +85OCStorage Temp -45OC to +100OC -45OC to +100OC

64.5 mm diameter x 14 mm high

Through any 13 mm min diameter hole Through any 13 mm min diameter hole

Model Order Codes ZAU-3C2M-GC


ZAU-3C3M-GC


ZAU-3C5M-GC

CELLULAR MOBILE PHONE ANTENNA SUMMARY · Cellular Mobile Phone Network Coverage ... Multiband NEXT...

Documents

Transcript of CELLULAR MOBILE PHONE ANTENNA SUMMARY · Cellular Mobile Phone Network Coverage ... Multiband NEXT...