Cell ID Position Method Optimization

2
 1.1.1 Cell ID position method Optimization  Description When CELL ID position method is selected, RNC will report corresponding descriptive type of the cell according to OMCR Benefit When CELL ID position method is selected and the cell is descri!ed with "rc or polygon type or other type, RNC will report the cell type information to CN Impacted Procedure Location service Impact if not upgrade When CELL ID position method is selected and the cell is descri!ed with "rc or polygon type, RNC will report only the cell center and cell radi#s with altit#de type information to CN Impact on other systems none Verification $ %he cell is config#red as polygon or arc or other type, and the corresponding cell descriptive type parameters are config#red & In position proced#re, Cell ID position method is selected Relative Parameter None 1.1. !a"imum Bit Rat e of #ign al ing at Cell $ev el Description  "dd a parameter C Res'ara( to l imit the ma)i m#m !it rate f or signaling in cell Benefit %he ratio of s#ccessf#l RRC connection can !e improved when I#! transmi ssion reso#rce i s limited Impacted Procedure DR*C Impact if not upgrade %he ratio of s#ccessf#l RRC connection can not !e improved when I#! transmission reso#rce is limited Impact on other systems None Verification $+ et the parameter CRes'ara( to -./  .( 0!ps1 &+ RRC connection will !e set #p #sing .( 0!ps R* Relative Parameter Reserved parameter/ CRes'ara( 2Cell Reserved 'arameter (+

description

Cell Optimizatiom

Transcript of Cell ID Position Method Optimization

Page 1: Cell ID Position Method Optimization

7/18/2019 Cell ID Position Method Optimization

http://slidepdf.com/reader/full/cell-id-position-method-optimization 1/2

1.1.1 Cell ID position method Optimization

DescriptionWhen CELL ID position method is selected, RNC will reportcorresponding descriptive type of the cell according to OMCR

BenefitWhen CELL ID position method is selected and the cell isdescri!ed with "rc or polygon type or other type, RNC willreport the cell type information to CN

Impacted Procedure Location service

Impact if not upgradeWhen CELL ID position method is selected and the cell isdescri!ed with "rc or polygon type, RNC will report only thecell center and cell radi#s with altit#de type information to CN

Impact on other systems

none

Verification

$ %he cell is config#red as polygon or arc or other type, andthe corresponding cell descriptive type parameters areconfig#red

& In position proced#re, Cell ID position method is selectedRelative Parameter  None

1.1. !a"imum Bit Rate of #ignaling at Cell $evel

Description "dd a parameter CRes'ara( to limit the ma)im#m !it rate forsignaling in cell

Benefit%he ratio of s#ccessf#l RRC connection can !e improvedwhen I#! transmission reso#rce is limited

Impacted Procedure DR*C

Impact if not upgrade%he ratio of s#ccessf#l RRC connection can not !e improved

when I#! transmission reso#rce is limitedImpact on other 

systemsNone

Verification$+ et the parameter CRes'ara( to -./  .( 0!ps1&+ RRC connection will !e set #p #sing .( 0!ps R*

Relative Parameter Reserved parameter/CRes'ara( 2Cell Reserved 'arameter (+

Page 2: Cell ID Position Method Optimization

7/18/2019 Cell ID Position Method Optimization

http://slidepdf.com/reader/full/cell-id-position-method-optimization 2/2

1.1.% &llocate the Common Channel Code &utomatically

Description

In previo#s RNC version, the Common Channel Code isallocated !y operators thro#gh OMCR Operators need toconsider the occ#pancy of code tree !y other physicalchannels Config#ration is complicated In this version, thecommon channel code of 3C'IC453CC'C45'IC45"IC4

5MIC4 can !e allocated a#tomatically Operators no longerneed to config#re the common channel code thro#gh OMCR

BenefitCommon Channel Code is allocated a#tomaticallyConfig#ration wor0 is simple

Impacted Procedure Code Reso#rce "llocation

Impact if not upgradeCommon Channel Code is allocated !y operators thro#ghOMCR

Impact on other systems

None

VerificationOperators needn6t to config#re the channel codes of 3C'IC45 3CC'C45'IC4 5"IC4 5MIC4 %he Cell can !e set #p

s#ccessf#lly

Relative Parameter 

Deleted parameter/$+ DlChCodeNo 23CC'C4 Channelisation Code No+&+ ChCode 2'IC4 Channelisation Code No+.+ ChCode 2"IC4 Channelisation Code No+(+ ChCode23C'IC4 Channelisation Code No+7+ MichChCode 2MIC4 Channelisation Code No+

1.1.' Controlla(le )actors of *#P& throughput +valuation for $oad Balance

Description

%he parameter CRes'ara8 to control whether or not toconsider code reso#rce, power, !andwidth in the calc#lation of 4'" thro#ghp#t %his parameter consists of three !its *it9,*it$ and *it& standing for code reso#rce, power and!andwidth separately If the !it val#e of the related factor is 9,the factor will not !e concerned

BenefitMeet the re:#irement of specific scene which cares only oneor two of the three factors mentioned a!ove

Impacted Procedure Load *alance

Impact if not upgrade %he re:#irement of specific scene can not !e met

Impact on other systems

None

VerificationWhen *it9;$, *it$;9, *it&;9, code reso#rce is considered inthe calc#lation of 4'" thro#ghp#t only

Relative Parameter  CRes'ara82R8CelInfo+