Cell Barring(RAN15.0 02)

WCDMA RAN

Cell Barring Feature ParameterDescription

Issue 02

Date 2013-11-15

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.Address: Huawei Industrial Base

Bantian, LonggangShenzhen 518129People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

Issue 02 (2013-11-15) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

i

http://www.huawei.com

mailto:[email protected]

Contents

1 Introduction....................................................................................................................................11.1 Scope..............................................................................................................................................................................11.2 Intended Audience..........................................................................................................................................................11.3 Change History...............................................................................................................................................................1

2 Overview.........................................................................................................................................3

3 Automatic Operation....................................................................................................................4

4 Manual operation..........................................................................................................................7

5 Engineering Guidelines.............................................................................................................105.1 When to Use.................................................................................................................................................................105.2 Deployment..................................................................................................................................................................105.2.1 Requirements.............................................................................................................................................................105.2.2 Data Preparation........................................................................................................................................................105.2.3 Activation..................................................................................................................................................................105.2.3.1 Using MML Commands.........................................................................................................................................105.2.3.2 MML Command Examples....................................................................................................................................125.2.3.3 Using the CME.......................................................................................................................................................125.2.4 Activation Check.......................................................................................................................................................135.2.5 Deactivation...............................................................................................................................................................165.2.5.1 Using MML Commands.........................................................................................................................................165.2.5.2 MML Command Examples....................................................................................................................................175.2.5.3 Using the CME.......................................................................................................................................................17

6 Parameters.....................................................................................................................................19

7 Counters........................................................................................................................................99

8 Glossary.......................................................................................................................................100

9 Reference Documents...............................................................................................................101

WCDMA RANCell Barring Feature Parameter Description Contents


ii

1 Introduction

1.1 ScopeThis document describes WRFD-021102 Cell Barring, including the basic concepts related tochannel element (CE) resources and basic methods of managing and controlling CE resources.

1.2 Intended AudienceThis document is intended for personnel who:

l Need to understand the features described hereinl Work with Huawei products

1.3 Change HistoryThis section provides information about the changes in different document versions. There aretwo types of changes, which are defined as follows:

l Feature changeChanges in features of a specific product version

l Editorial changeChanges in wording or addition of information that was not described in the earlier version

02 (2013-11-15)This issue includes the following changes.

Change Type Change Description Parameter Change

Feature change None. None.

WCDMA RANCell Barring Feature Parameter Description 1 Introduction


1


Editorial change Optimized the description ofactions taken by the RNCwhen the Iu interface isunavailable. For details, seechapter 3 AutomaticOperation.

None.

01(2013-04-28)This issue does not include any changes.

Draft A (2013-01-30)Compared with issue 01 (2012-07-20) of RAN14.0, Draft A (2013-01-30) of RAN15.0 includesthe following changes.


Feature change None. None.

Editorial change Modified descriptions aboutautomatic operation. Fordetails, see chapter 3Automatic Operation.

None.

WCDMA RANCell Barring Feature Parameter Description 1 Introduction


2

2 Overview

This document describes the feature WRFD-021102 Cell Barring.

When a cell is abnormal, this feature enables the operator to automatically or manually bar thecell.

l When the Iu interface is disconnected, this feature can prevent the UE from initiating uselessaccess requests and ensure that 3G UEs are handed over to the 2G network.

l This feature can provide flexibility for the operator in some scenarios (for example,maintenance).

The cell can be barred or unbarred manually and automatically.

l Manual operation. The operator can bar/unbar the cell by the MML commands. And thenRNC will update the system information of this cell to indicate UE the change;

l Automatic operation. In cases of Iu-CS or Iu-PS breakdown, the RNC keeps providingcoverage (but not service) to the UEs under its control. This means that several UEs arekept in 3G coverage, but, actually, they cannot access the network. If the Iu-CS breaksdown, the RNC will bar the CS domain service for the cell; if the Iu-PS breaks down, theRNC will bar the PS domain service for the cell. In the case of both Iu-CS and Iu-PSbreakdown, RNC bars the cell automatically.

The RAN notifies the UE through SIB about the information of cell barring. And the UE detectsSIB and access the network according to the SIB.

l If SIB1 does not contain the information of one CN domain (CS or PS), the UE does notinitiate services in this domain and does not reselect cells but camps in the current cell.

l If the SIB3/4 indicates the cell is barred, the UE is not permitted to select/re-select this cell,not even for emergency calls. UE firstly tries to camp on configured 3G/2G neighboringcells. If all cells cannot be camped on, the UE tries to search new network.

WCDMA RANCell Barring Feature Parameter Description 2 Overview


3

3 Automatic Operation

The RNC take actions according to the faults on the Iu:

l If only the Iu UP breaks up, the RNC takes no action.

If the Iu breaks up, and does not recover in the period StateIndTmr(BSC6900,BSC6910), the RNC takes the Iu as faulty.

If there are only intermittent disconnections, the RNC does not release the signalingconnection. If the duration of the fault exceeds the StateIndTmr(BSC6900,BSC6910) andis not recovered, the RNC judges that the connection to the CN breaks up and releases allthe signaling connection to the CN.

l When only the Iu-CS signaling link breaks up:

If… Then…

SYS_INFO_UPDATE_FOR_IU_RST Switch Underthe RNC-levelPROCESSSWITCH(BSC6900,BSC6910)Parameter

SYS_INFO_UPDATE_FOR_IU_RST SwitchUnder the Cell-levelNBMCacAlgoSwitch(BSC6900,BSC6910)Parameter

BARRED_CELL_FOR_CSDOMAIN_RST SwitchUnder thePROCESSSWITCH(BSC6900,BSC6910)Parameter

OFF OFF OFF The event of Iu-CSsignaling linkdisconnection is masked.The SIB1 still containsinformation about the CSdomain, but the SIB3/SIB4 does not indicatethat the cell has beenbarred. In this situation,the UE can initiate bothCS and PS servicerequests, but the RNC will

OFF OFF ON

OFF ON OFF

WCDMA RANCell Barring Feature Parameter Description 3 Automatic Operation


4

OFF ON ON reject the CS servicerequests. The PS servicerequests will not beaffected.

ON OFF OFF The SIB1 does not containthe information about theCS domain. In thissituation, the UE will notinitiate CS services orreselect a network.

ON OFF ON

ON ON OFF

ON ON ON The SIB3/SIB4 indicatesthat the cell has beenbarred. In this situation,the UE will reselect a cell.

NOTE

l The SYS_INFO_UPDATE_FOR_IU_RST switch under the RNC-level PROCESSSWITCH(BSC6900,BSC6910) parameter is set using the SET URRCTRLSWITCH command.

l The SYS_INFO_UPDATE_FOR_IU_RST switch under the cell-level NBMCacAlgoSwitch(BSC6900,BSC6910) parameter is set using the ADD UCELLALGOSWITCH or MODUCELLALGOSWITCH command.

l The BARRED_CELL_FOR_CSDOMAIN_RST switch under the PROCESSSWITCH(BSC6900,BSC6910) parameter is set using the SET URRCTRLSWITCH command.

l When the Iu-PS signaling link breaks up:

– If SYS_INFO_UPDATE_FOR_IU_RST is turned on, the SIB1 does not contain PSCN information. In this case, the UE will not initiate PS services or reselect a network.

– If SYS_INFO_UPDATE_FOR_IU_RST is turned off, the event of Iu-PS signalinglink disconnection is masked. The SIB1 still contains the PS CN information. In thiscase, the UE can initiate a PS service request but the RNC will reject the request.

l When the signaling links of both Iu-CS and Iu-PS break up:

If… Then…



5

SYS_INFO_UPDATE_FOR_IU_RST Switch Underthe RNC-levelPROCESSSWITCH(BSC6900,BSC6910)Parameter

SYS_INFO_UPDATE_FOR_IU_RSTSwitch Under theCell-levelNBMCacAlgoSwitch(BSC6900,BSC6910)Parameter

ON ON The SIB3/SIB4 indicates that the cell hasbeen barred. In this situation, the UE willreselect a cell.

ON OFF The event of Iu-CS and Iu-PS signaling linkdisconnection is masked. The SIB1 stillcontains information about the CS and PSdomains, but the SIB3/SIB4 does notindicate that the cell has been barred. In thissituation, the UE can initiate both CS andPS service requests, but the RNC will rejectthe requests.

After the Iu recovers, the cells are automatically unbarred.

When the Iu interface is faulty, the RNC gradually restricts cell access in Bar mode. When theIu interface is restored, the RNC gradually enables cell access in Not Bar mode. The parameterIuAcIntervalOfCell(BSC6900,BSC6910) defines the interval from barring/unbarring one cellto barring/unbarring another cell. In this way, the location update procedure can be distributedto a specified time period and the risk due to congestion is reduced.



6

4 Manual operation

Quick blocking/unblocking of cells is required in some special scenarios. For example, if theRNC is faulty when the UE camps on the 3G network, the RNC cannot provide complete serviceson the access network; if the CN needs to be upgraded, the UE must be forcibly handed overfrom the 3G network to the 2G network. Although the BLK ULOCELL command can beexecuted to block/unblock cells in batches, this method requires longer preparation andprocessing time. Therefore, it does not meet the requirement for quickly blocking/unblockingcells.

Quick blocking/unblocking of cells is a process of UE access control through the AC controlIEs in the cell system information. It is effective for the UEs in idle mode. The blocking modesare as follows:

l Blocking all the cells controlled by an RNC through the ADD URNCALLCELLBLKcommand. Cell blocking can be performed in the PS domain or in both the PS domain andthe CS domain, which is set by the DomainType(BSC6900,BSC6910) parameter. Theprocessing time of cell blocking is set by the ProcessDuration(BSC6900,BSC6910)parameter.

l Blocking PS services for a cell controlled by an RNC by setting the DomainType(BSC6900,BSC6910) parameter to PsBlk in the ADD/MOD UCELLACCESSSTRICTcommand.

l Blocking all the cells belonging to an operator through the ADDUCNOPALLCELLBLK command. Cell blocking can be performed in the PS domain orin both the PS domain and the CS domain, which is set by the DomainType(BSC6900,BSC6910) parameter. The processing time of cell blocking is set by theProcessDuration(BSC6900,BSC6910) parameter.

NOTE

l Only one blocking mode can be used for quick blocking/unblocking of cells, that is, the blocking modesbased on RNC and Operator cannot be used simultaneously.

l In the latter blocking mode, the ADD UCNOPALLCELLBLK command is executed for only oneoperator.

Cell blocking can be performed in the PS domain or in both the PS domain and the CS domain,which is set by the DomainType(BSC6900,BSC6910) parameter. The processing time of cellblocking is set by the ProcessDuration(BSC6900,BSC6910) parameter.

Table 4-1 provides five schemes for quickly blocking/unblocking cells.

WCDMA RANCell Barring Feature Parameter Description 4 Manual operation


7

Table 4-1 Five schemes for quickly blocking/unblocking cells

Target Object Blocked Domain Scheme UE VersionCompatibility

RNC PS domain Delete theinformation aboutthe PS domain fromSIB1. Only theinformation aboutthe CS domain isbroadcast.

Any new PS serviceis rejected. Thisscheme is effectivefor all the UEs.

RNC CS domain and PSdomain

Set all the ACs in the"Access ClassBarred list" IE inSIB3/4 to barred.In addition, set all theACs in the "DomainSpecific AccessRestrictionParameters For All"IE in the "DomainSpecific AccessRestriction ForShared Network" IEto barred.

Any new service isrejected. Thisscheme is effectivefor all the UEs.

Operator PS domain Set all the PS ACs inthe "DomainSpecific AccessRestrictionParameters ForOperatorN" IE in the"Domain SpecificAccess RestrictionFor Shared Network"IE in SB1 to barred.In addition, set theCS domain tonoRestriction(NULL).

Any new PS serviceis rejected. Thisscheme is effectivefor the UEs of 3GPPRelease 6 or later.



8

Target Object Blocked Domain Scheme UE VersionCompatibility

Operator CS domain and PSdomain

Set all the CS ACsand PS ACs in the"Domain SpecificAccess RestrictionParameters ForOperatorN" IE in the"Domain SpecificAccess RestrictionFor Shared Network"IE to barred.

Any new service isrejected. Thisscheme is effectivefor the UEs of 3GPPRelease 6 or later.

CELL PS domain Delete theinformation aboutthe PS domain fromSIB1. Only theinformation aboutthe CS domain isbroadcast.

Any new PS serviceis rejected. Thisscheme is effectivefor all the UEs in thecell.



9

5 Engineering Guidelines

5.1 When to UseThe use of this feature does not affect the KPI of local network, because after the cell is barredthe UE will not retry to access the local cell. However, the UE will try to access inter-RAT cellsor inter-operator cells in the same coverage and cause signaling shock to them. Therefore, youneed to consider the anti-shock capability when deploying this feature and ensure the cell canwork normally when a lot of UEs come to the cells.

It is recommended that you use the default values of the parameters involved in this feature.

5.2 Deployment

5.2.1 RequirementsNone

5.2.2 Data PreparationNone

5.2.3 Activation

5.2.3.1 Using MML Commands

Automatic Cell Barring

To enable the function of the automatic cell barring, run the following command:

Step 1 Run the RNC MML command SET URRCTRLSWITCH. In this step, selectSYS_INFO_UPDATE_FOR_IU_RST and BARRED_CELL_FOR_CSDOMAIN_RSTfrom the Process switch drop-down list.

WCDMA RANCell Barring Feature Parameter Description 5 Engineering Guidelines


10

Step 2 Run the RNC MML command ADD UCELLALGOSWITCH or MODUCELLALGOSWITCH. In this step, select SYS_INFO_UPDATE_FOR_IU_RST from theCell CAC algorithm switch drop-down list.

Step 3 Run the RNC MML command SET UIUTIMERANDNUM (CME single configuration: IUPSConfiguration Express > CN > IU Timers And Counter for CN Node; CME batch modificationcenter: not supported) to enable interruption protection by specifying CN protection timer .

----End

Quickly Blocking One CellWhen a cell is blocked in high priority, the cell is deactivated immediately. When a cell is blockedin medium priority, the cell is deactivated immediately if no subscriber accesses the cell in theduration specified for blocking of medium priority, or if any subscriber accesses the cell in theduration specified for blocking of medium priority the cell is deactivated after the durationspecified for blocking of medium priority expires. When a cell is blocked in low priority, thecell is deactivated when no subscriber accesses the cell.

To block a cell run the following command:

Step 1 Run the RNC MML command BLK ULOCELL to set Block PRI to HIGH(HIGH).

----End

To unblock a cell, run the following command:

Step 1 Run the RNC MML command UBL ULOCELL to unblock a cell.

----End

Quickly Blocking All the CellsThe function of quickly blocking all the cells only can chose one of the following methods:

Step 1 Run the RNC MML command ADD URNCALLCELLBLK (CME single configuration:UMTS Radio Global Configuration Express > Access Restriction Algorithm ParametersConfiguration > The Parameters for Quickly Blocking all the Cells in the RNC; CME batchmodification center: not supported) to configure parameters related to barring of all cells servedby an RNC in a network.

Step 2 Run the RNC MML command ADD UCNOPALLCELLBLK (CME single configuration:UMTS Radio Global Configuration Express > Access Restriction Algorithm ParametersConfiguration > The Parameters for Quickly Blocking all the Cells of the Designated Operatorin the RNC; CME batch modification center: not supported) to configure parameters related tooperator-specific barring of all cells in a network.

----End

To block all the cells in the RNC in the PS domain in 10 minutes, run the following command:

Step 1 Run the RNC MML command ADD URNCALLCELLBLK to set Blocked Domain Type toPsBlk, set Processing Duration to 10.

----End

To unblock all the cells in the RNC:



11

Step 1 Run the RNC MML command RMV URNCALLCELLBLK to unblock all the cells in theRNC

----End

5.2.3.2 MML Command Examples//Activating Cell Barring SET URRCTRLSWITCH: PROCESSSWITCH = SYS_INFO_UPDATE_FOR_IU_RST-1; SET URRCTRLSWITCH: PROCESSSWITCH = BARRED_CELL_FOR_CSDOMAIN_RST-1; MOD UCELLALGOSWITCH: CellId=100, NBMCacAlgoSwitch=SYS_INFO_UPDATE_FOR_IU_RST-1;SET UIUTIMERANDNUM: CnOpIndex=0, CNId=0, StateIndTmr=20000;

5.2.3.3 Using the CMENOTE

When configuring the UMTS-to-LTE Fast Return feature on the CME, perform a single configuration first,and then perform a batch modification if required.

Configure the parameters of a single object before a batch modification. Perform a batch modificationbefore logging out of the parameter setting interface.

Step 1 Configure a single object (such as a cell) on the CME.

Set the parameters described in Table 5-1 on the CME. For instructions on how to perform theCME single configuration, see CME Single Configuration Operation Guide.

Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center)

To modify objects in batches, click on the CME to start the batch modification wizard. Forinstructions on how to perform a batch modification through the CME batch modification center,press F1 on the wizard interface to obtain online help.

----End

Table 5-1 Configuring parameters on the CME

SN MO NE ParameterName

ParameterID

Configurable in CMEBatchModification Center

1 URRCTRLSWITCH

RNC Processswitch(turnon theSYS_INFO_UPDATE_FOR_IU_RST andBARRED_CELL_FOR_CSDOMAIN_RSTswitches)

PROCESSSWITCH(BSC6900,BSC6910)

Yes



12


ParameterID


2 UCELLALGOSWITCH

RNC Cell CACalgorithmswitch (turnon theSYS_INFO_UPDATE_FOR_IU_RST switch)

NBMCacAlgoSwitch(BSC6900,BSC6910)

3 UIUTIMERANDNUM

RNC CNprotectiontimer

StateIndTmr(BSC6900,BSC6910)

Yes

5.2.4 Activation CheckBlock the PS domain or the PS domain is disconnected, which prevents UEs from being admittedto PS services. Perform the following steps to verify whether this feature is activated:

NOTE

Perform the same verification procedure when blocking the CS domain or the CS domain is disconnected.

Step 1 Click to display Uu Interface Trace on the RNC LMT. Under Uu Message Type, selectRRC_SYS_INFO_TYPE1.

Step 2 View whether information element (IE) information of the PS domain is contained in the tracedmessages. Expected result: PS domain IE information is not contained, as shown in Figure5-1.

----End



13

Figure 5-1 Uu Interface Trace dialog box

Block CS and PS domains, CS and PS domains are disconnected, or block the CS domain andturn on BARRED_CELL_FOR_CSDOMAIN_RST. Perform the following steps to verifywhether this feature is activated:


Step 2 View whether IE information related to CS and PS domains is contained in the traced messages.Expected result: The IE information is not contained, as shown in Figure 5-2.

----End



14


Bar PS services of UEs served by an operator. Perform the following steps to verify whetherthis feature is activated:

NOTE

Perform the same verification procedure when barring CS services of UEs served by an operator.


Step 2 View whether IE information related to CS and PS domains is contained in the traced messages.Expected result: The IE information is not contained, as shown in Figure 5-3.

----End



15


5.2.5 Deactivation

5.2.5.1 Using MML Commands

Deactivating automatic cell barring

Step 1 Run the RNC MML command SET URRCTRLSWITCH. In this step, deselectSYS_INFO_UPDATE_FOR_IU_RST and BARRED_CELL_FOR_CSDOMAIN_RSTfrom the Process switch drop-down list.

Step 2 Run the RNC MML command ADD UCELLALGOSWITCH or MODUCELLALGOSWITCH. In this step, deselect SYS_INFO_UPDATE_FOR_IU_RST fromthe Cell CAC algorithm switch drop-down list.

----End

Deactivating manual cell barring

Step 1 Run the RNC MML command RMV URNCALLCELLBLK to remove parameters related tobarring of all cells served by an RNC in a network.



16

Step 2 Run the RNC MML command RMV UCNOPALLCELLBLK to remove parameters relatedto operator-specific barring of all cells in a network.

----End

5.2.5.2 MML Command Examples//Deactivating Cell Barring SET URRCTRLSWITCH: PROCESSSWITCH = SYS_INFO_UPDATE_FOR_IU_RST-0; MOD UCELLALGOSWITCH: CellId=100, NBMCacAlgoSwitch=SYS_INFO_UPDATE_FOR_IU_RST-0;SET URRCTRLSWITCH: PROCESSSWITCH = BARRED_CELL_FOR_CSDOMAIN_RST-0;

5.2.5.3 Using the CME

Deactivating automatic cell barring

NOTE

When configuring the UMTS-to-LTE Fast Return feature on the CME, perform a single configuration first,and then perform a batch modification if required.

Configure the parameters of a single object before a batch modification. Perform a batch modificationbefore logging out of the parameter setting interface.

Step 1 Configure a single object (such as a cell) on the CME.

Set the parameters described in Table 5-2 on the CME. For instructions on how to perform theCME single configuration, see CME Single Configuration Operation Guide.

Step 2 (Optional) Modify objects in batches on the CME. (CME batch modification center)

To modify objects in batches, click on the CME to start the batch modification wizard. Forinstructions on how to perform a batch modification through the CME batch modification center,press F1 on the wizard interface to obtain online help.

----End



17

Table 5-2 Configuring parameters on the CME


ParameterID


1 URRCTRLSWITCH

RNC Processswitch (turnoff theSYS_INFO_UPDATE_FOR_IU_RST andBARRED_CELL_FOR_CSDOMAIN_RSTswitches)

PROCESSSWITCH(BSC6900,BSC6910)

Yes

2 UCELLALGOSWITCH

RNC Cell CACalgorithmswitch (turnoff theSYS_INFO_UPDATE_FOR_IU_RST switch)

NBMCacAlgoSwitch(BSC6900,BSC6910)

Yes

Deactivating manual cell barringThis feature cannot be configured by using the CME.



18

6 Parameters

Table 6-1 Parameter description

Parameter ID NE MMLCommand

Feature ID Feature Name Description

StateIndTmr BSC6900 SETUIUTIMERANDNUM

WRFD-010101WRFD-021102

3GPP R9SpecificationsCell Barring

Meaning:Inter-mittentdisconnectionprotection timefor a link. Thisparameter is anadvancedparameter. Tomodify thisparameter,contact HuaweiCustomerService Centerfor technicalsupport.GUI ValueRange:1000~300000Unit:msActual ValueRange:1000~300000Default Value:20000

WCDMA RANCell Barring Feature Parameter Description 6 Parameters


19



StateIndTmr BSC6910 SETUIUTIMERANDNUM

WRFD-010101WRFD-021102

3GPP R9SpecificationsCell Barring

Meaning:Inter-mittentdisconnectionprotection timefor a link. Thisparameter is anadvancedparameter. Tomodify thisparameter,contact HuaweiCustomerService Centerfor technicalsupport.GUI ValueRange:1000~300000Unit:msActual ValueRange:1000~300000Default Value:20000



20



PROCESSSWITCH

BSC6900 SETURRCTRLSWITCH

WRFD-021102WRFD-150205WRFD-150204WRFD-010101WRFD-150231WRFD-020500WRFD-021303WRFD-020132WRFD-020124WRFD-140206WRFD-020134WRFD-020128WRFD-01061212WRFD-010641WRFD-020806

Cell BarringLayered Pagingin Idle ModePlatinum UserPrioritizing3GPP R9SpecificationsRIM BasedUMTS TargetCell Selectionfor LTEEnhanced FastDormancyIMSI BasedHandoverWeb browsingaccelerationUplink FlowControl of UserPlaneLayered Pagingin URA_PCHPush to TalkQualityImprovementfor SubscribedServiceHSUPA IubFlow Control inCase of IubCongestionHSUPAAdaptiveTransmissionDifferentiatedService Basedon SPI Weight

Meaning:1)INVOKE_TRACE_SWITCH.1: This switch isturned on. RNCwill start InvokeTrace procedureupon receivingINVOKETRACEMessage formCN. 0: Thisswitch is turnedoff. RNC won'tstart the InvokeTrace procedurethough itreceives theINVOKETRACEmessage. 2)SYS_INFO_UPDATE_FOR_IU_RST. 1: Thisswitch is turnedon. The SIB1does not containbroken-downCN information.In this case, theUE will notselect broken-down networkwhen Iutransmissionfailure occurs. 0:This switch isturned off. TheSIB1 containsthe broken-down CNinformation. Inthis case, the UEwill selectbroken-downnetwork but theRNC will rejectthe request when



21



Iu transmissionfailure occurs. 3)DRNC_DIRECT_DSCR.Whether theDirectedSignalingConnection re-establishment(DSCR)procedure istriggered duringa cell updateover the Iurinterface forUEs that are notin theCELL_DCHstate or for UEsthat are in theCELL_DCHstate and do nothave an Iurconnection. Thisswitch is set onthe drift radionetworkcontroller(DRNC) side. 1:This switch isturned on.DRNC will startDSCRproceduredirectly in RRCstates other thanCELL_DCH orCELL_DCHthat do not havean Iurconnection. 0:This switch isturned off.DRNC willtransfer RRCCELL UPDATEmessage toSRNC. 4)



22



PTUSER_IDENTIFY_ENH_SWITCH(Platinum useridentifyenhancementswitch) Whetherplatinum usersare identified inDRNC orrelocationscenarios. 1:This switch isturned on.Platinum usersare identifiedand theirservices areguaranteed inDRNC orrelocationscenarios. 0:This switch isturned off.Platinum usersare notidentified inDRNC orrelocationscenarios. 5)RNC_SHARE_SWITCH. 1:This switch isturned on. Thetraffic sharingfunction isenabled. 0: Thisswitch is turnedoff. The trafficsharing functionis disabled,service accesswill be affectedunder heavytraffic. 6)RNCAP_IMSI_HO_SWITCH.1: This switch is



23



turned on. Imsihandoverfunction will beused. 0: Thisswitch is turnedoff. Imsihandoverfunction will notbe used. 7)TERMINAL_VERSION_DEBASE_SWITCH.1: This switch isturned on.Terminalversion R4 willdebase to R99.0: This switch isturned off.Terminalversion R4 willnot debase toR99. 8)SYS_HO_OUT_CIPHER_SWITCH. 1: Thisswitch is turnedon. The RNCwill addciphering byte atGSMHANDOVERCOMMAND ifthe GSM systemdo not add anycipherinformation atthat message. 0:This switch isturned off. TheRNC will notadd cipheringbyte at GSMHANDOVERCOMMAND ifthe GSM systemdo not add anycipher



24



information atthat message. 9)SYS_HO_CIPHER_CONFIG.1: This switch isturned on. Thecipherconfiguration inthe added cipherbyte in GSMwill be A5/1. 0:This switch isturned off. Thecipherconfiguration isA5/0. 10)BARRED_CELL_FOR_CSDOMAIN_RST. 1:This switch isturned on. Cellwill be baredwhen CSdomain isinvalid. 0: Thisswitch is turnedoff. The CSdomain will bebared when CSdomain isinvalid. It isinvalid IfSYS_INFO_UPDATE_FOR_IU_RST is notchecked. 11)CR2284R1_SWITCH. 1: Thisswitch is turnedon. The RNCperforms theprocessingbased onCR2284R1, thatis, based on thedescription insection 8.6.6.28of Release 5 TS



25



25.331. In thissection, itdescribes thatthe HFN isincreased by onewhen RB setupis accompaniedby a Timing re-initialized hardhandover. 0:This switch isturned off. TheHFN is notincreased by onewhen RB setupis accompaniedby a Timing re-initialized hardhandover. 12)CDT_MSG_FULL_TRACE. 1:This switch isturned on. CDTtrace functionstarts tracingfrom messageRRCCONNECTREQUEST. 0:This switch isturned off. CDTtrace functionstarts tracingfrom messageCOMMON ID.13)CR2284R1_COMPATIBLE_SWITCH.CR2284R1causes thecompatibleproblem. if UEis not consistentwith RNCregardingwhether acceptthe CR2284R1



26



or not, it willcause theproblem ofstreaming whenUEs arecommunicatingwith each other.So RNC createsthis switch.when it ischecked, RNC isauto-adaptive toaccept theCR2284R1according to UEversioninformation.The principlesthat RNC judgesUE whether toaccept theCR2284R1 areas follows: R5and above UEaccepts the CR;R99/R4 UE, if itreceives theSTART LISTvalue from RBSETUPCOMPLETE,RNC figures thatUE accepts theCR; R99/R4 UE,if it onlyreceives theSTART valuefrom RBSETUPCOMPLETE,RNC figures thatUE does notaccept the CR;when it is notchecked,whether RNCaccept the CR ornot is according



27



toCR2284R1_SWITCH. Therelationsbetween thesetwo switchesCR2284R1_SWITCH andCR2284R1_COMPATIBLE_SWITCH are asfollows: 1: Thisswitch is turnedon. RNC is self-compatible, sotheCR2284R1_SWITCH is invalid;0: This switch isturned off. TheCR2284R1_SWITCH is valid.14)COMBINE_OPERATION_DRD_SWITCH. 1:This switch isturned on. RNCwill not rejectthe message RBSETUP CMPwithout the IEactive time. 0:This switch isturned off. RNCwill reject themessage RBSETUP CMPwithout the IEactive time. 15)UL_INTER_PROTECT_SWITCH. 1: Thisswitch is turnedon. RNC will dointegrityprotection checkfor uplink RRC



28



messages. 0:This switch isturned off. RNCwill not dointegrityprotection checkfor uplink RRCmessages. 16)FAST_DORMANCY_SWITCH. 1: This switchis turned on.RNC will applyFASTDORMANCYfunction. 0: Thisswitch is turnedoff. RNC willnot apply FASTDORMANCYfunction. 17)SYS_HO_IN_CIPHER_SWITCH. During anincoming GSM-to-UMTShandover, if theRNC cannotobtain a UE'sencryptioncapabilityinformationfrom theRELOC REQmessage: 1: Thisswitch is turnedon. Theencryptionalgorithm that isconfigured forboth the RNCand CN is used.For example, ifthe CN isconfigured withthe encryptionalgorithm UEA1and the RNC is



29



configured withencryptionalgorithmsUEA0 andUEA1, then theRNC uses theencryptionalgorithmUEA1. 0: Thisswitch is turnedoff. Defaultconfigured ofencryptedparameter UIA1and UEA0 isused. 18)PTT_EARLY_TRANS_SWITCH_OFF. 1:This switch isturned on. PTTuser will notapply the earlytransmissionfunction. 0: Thisswitch is turnedoff. PTT userwill apply theearlytransmissionfunction. 19)UPLINK_MDC_ENHENCEMENT_SWITCH.This switch hasbecome invalid.20)NODEB_PRIVATE_INTERFACE_SWITCH.1: This switch isturned on. TheNodeB privateinterface datacan be taken tothe NodeBthrough the IUBprotocol



30



message. 0: Thisswitch is turnedoff. The NodeBprivate interfacedata can not betaken to theNodeB throughthe IUB protocolmessage. 21)PTT_SPEC_LI_SWITCH_OFF.1: This switch isturned on.Special LI(LengthIndicator) willnot be used forPTT user. 0:This switch isturned off.Special LI(LengthIndicator) willbe used for PTTuser. 22)RNC_DF_2_URA_PCH_SWITCH. 1: Thisswitch is turnedon. RNC willsupporttransferring FastDormancy UEfromCELL_DCH orCELL_FACH toURA_PCH. 0:This switch isturned off. RNCwill not supporttransferring FastDormancy UEfromCELL_DCH orCELL_FACH toURA_PCH. 23)FD_TAC_MATCH_SWITCH.



31



1: This switch isturned on. TheRNC uses TACmatching todeterminewhether to applythe FASTDORMANCYfunction for prefast dormancyUEs. 0: Thisswitch is turnedoff. The RNCapplies theFASTDORMANCYfunction for prefast dormancyUEs of 3GPPRelease 5 orlater. 24)NONPTT_L1_FAST_SYNC_SWITCH. 1: Thisswitch is turnedon. If a UE setsup a non-PTTservice on theDCH, the RNCincludes thePost-verificationperiodinformationelement (IE) in aUu message toinstruct the UEto performconcurrentuplink anddownlinksynchronization. 0: This switchis turned off. If aUE sets up anon-PTT serviceon the DCH, theRNC does not



32



include the Post-verificationperiod IE in a Uumessage. TheUE firstperformsdownlinksynchronizationand then uplinksynchronization. 25)URAPCH_LAYERED_PAGING_RT_SWITCH. Whether theRNC allowsLayered Pagingin URA_PCHfor a UEprocessing real-time services. 1:This switch isturned on. TheRNC sendspagingmessages to thecell on which aUE processingreal-timeservices campedrecently and tothe neighboringcells of this cell.The RNC pagesthe UE in theentire UTRANregistration area(URA) onlywhen it does notreceive aresponse fromthe UE. Thissignificantlyreduces thenumber ofpagingmessages on theUu interface. 0:



33



This switch isturned off. TheRNC directlypages the UE inthe entire URA.26)URAPCH_LAYERED_PAGING_NRT_SWITCH. Whether theRNC allowsLayered Pagingin URA_PCHfor a UEprocessing non-real-timeservices. 1: Thisswitch is turnedon. The RNCsends pagingmessages to thecell on which aUE processingnon-real-timeservices campedrecently and tothe neighboringcells of this cell.The RNC pagesthe UE in theentire URA onlywhen the RNCdoes not receivea response fromthe UE. Thissignificantlyreduces thenumber ofpagingmessages on theUu interface. 0:This switch isturned off. TheRNC directlypages the UE inthe entire URA.27)IDLE_LAYER



34



ED_PAGING_NRT_SWITCH.Whether toenable layeredpaging for UEsin the idle statewho willestablish non-real-timeservice. 1: Thisswitch is turnedon. The firstbroadcasts apaging messagein the cell whohas interactedwith the UE forthe last time andits neighboringcells. If the UEcannot be paged,the RNC thenbroadcasts apaging messagein the LAC orRAC area. 0:This switch isturned off. TheRNC directlybroadcasts apaging messagein the LAC orRAC area. 28)IDLE_LAYERED_PAGING_RT_SWITCH.Whether toenable layeredpaging for UEsin the idle statewho willestablish real-time service. 1:This switch isturned on. Firstbroadcasts apaging messagein the cell who



35



has interactedwith the UE forthe last time andits neighboringcells. If the UEcannot be paged,the RNC thenbroadcasts apaging messagein the LAC orRAC area. 0:This switch isturned off. TheRNC directlybroadcasts apaging messagein the LAC orRAC area. 29)INTELLIGENT_WIFI_DETECT_AND_SELECTION.Whether toenableintelligent Wi-Fidetection andselection for theRNC. 1: Thisswitch is turnedon. The RNCsupportsintelligent Wi-Fidetection andselection. 0:This switch isturned off. TheRNC does notsupportsintelligent Wi-Fidetection andselection. 30)INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH.Whether toenable the RIM-based cell load



36



sharing function(MultipleReport). 1: Thisswitch is turnedon. RIM-basedload sharing canbe achievedbetween UMTSand LTE cells.Upon receivinga load sharingrequest from anLTE cell, aUMTS cellresponds with itsown loadinformation. 0:This switch isturned off.UMTS cells donot support theRIM-based cellload sharingfunction.Therefore,UMTS cells donot respond toload sharingrequests fromLTE cells. 31)PTUSER_IDENTIFY_SWITCH. Whether topreferentiallyguaranteeplatinum usersin terms ofnetwork access,voice quality, orPS service rate.1: This switch isturned on. TheRNC recognizesplatinum usersandpreferentiallyguarantees theiruser experience.



37



0: This switch isturned off. TheRNC does notrecognizeplatinum usersand does notpreferentiallyguarantee theiruser experience.DisuseStatement:Infuture versions,theRNC_SHARE_SWITCH,TERMINAL_VERSION_DEBASE_SWITCH,CR2284R1_SWITCH,CR2284R1_COMPATIBLE_SWITCH,COMBINE_OPERATION_DRD_SWITCHandUPLINK_MDC_ENHENCEMENT_SWITCHbit field valueunder thePROCESSSWITCH parameterwill be deleted.Although theconfigurationinterface in thisversion supportsdelivery andsynchronizationof the bit fieldvalue, the bitfield value is nolonger internallyused. Instead,the function ofRNC_SHARE_



38



SWITCH willbe controlled bytheRncShareSwitch parameter inthe SETUCTRLPLNSHAREPARAcommand.GUI ValueRange:INVOKE_TRACE_SWITCH,SYS_INFO_UPDATE_FOR_IU_RST,DRNC_DIRECT_DSCR,PTUSER_IDENTIFY_ENH_SWITCH,RNC_SHARE_SWITCH,RNCAP_IMSI_HO_SWITCH,TERMINAL_VERSION_DEBASE_SWITCH,SYS_HO_OUT_CIPHER_SWITCH,SYS_HO_CIPHER_CONFIG,BARRED_CELL_FOR_CSDOMAIN_RST,CR2284R1_SWITCH,CDT_MSG_FULL_TRACE,CR2284R1_COMPATIBLE_SWITCH,COMBINE_OPERATION_DRD_SWITCH,UL_INTER_PR



39



OTECT_SWITCH,FAST_DORMANCY_SWITCH,SYS_HO_IN_CIPHER_SWITCH,PTT_EARLY_TRANS_SWITCH_OFF,UPLINK_MDC_ENHENCEMENT_SWITCH,NODEB_PRIVATE_INTERFACE_SWITCH,PTT_SPEC_LI_SWITCH_OFF,RNC_DF_2_URA_PCH_SWITCH,FD_TAC_MATCH_SWITCH,NONPTT_L1_FAST_SYNC_SWITCH,URAPCH_LAYERED_PAGING_RT_SWITCH,URAPCH_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_RT_SWITCH,INTELLIGENT_WIFI_DETECT_AND_SELECTION,INTERRAT_LOAD_REPORT_FOR_LTE_S



40



WITCH,PTUSER_IDENTIFY_SWITCHUnit:NoneActual ValueRange:INVOKE_TRACE_SWITCH,SYS_INFO_UPDATE_FOR_IU_RST,DRNC_DIRECT_DSCR,PTUSER_IDENTIFY_ENH_SWITCH,RNC_SHARE_SWITCH,RNCAP_IMSI_HO_SWITCH,TERMINAL_VERSION_DEBASE_SWITCH,SYS_HO_OUT_CIPHER_SWITCH,SYS_HO_CIPHER_CONFIG,BARRED_CELL_FOR_CSDOMAIN_RST,CR2284R1_SWITCH,CDT_MSG_FULL_TRACE,CR2284R1_COMPATIBLE_SWITCH,COMBINE_OPERATION_DRD_SWITCH,UL_INTER_PROTECT_SWITCH,FAST_DORMANCY_SWITCH,



41



SYS_HO_IN_CIPHER_SWITCH,PTT_EARLY_TRANS_SWITCH_OFF,UPLINK_MDC_ENHENCEMENT_SWITCH,NODEB_PRIVATE_INTERFACE_SWITCH,PTT_SPEC_LI_SWITCH_OFF,RNC_DF_2_URA_PCH_SWITCH,FD_TAC_MATCH_SWITCH,NONPTT_L1_FAST_SYNC_SWITCH,URAPCH_LAYERED_PAGING_RT_SWITCH,URAPCH_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_RT_SWITCH,INTELLIGENT_WIFI_DETECT_AND_SELECTION,INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH,PTUSER_IDENTIFY_SWITCH



42



DefaultValue:INVOKE_TRACE_SWITCH:0,SYS_INFO_UPDATE_FOR_IU_RST:0,DRNC_DIRECT_DSCR:0,PTUSER_IDENTIFY_ENH_SWITCH:0,RNC_SHARE_SWITCH:1,RNCAP_IMSI_HO_SWITCH:0,TERMINAL_VERSION_DEBASE_SWITCH:0,SYS_HO_OUT_CIPHER_SWITCH:0,SYS_HO_CIPHER_CONFIG:1,BARRED_CELL_FOR_CSDOMAIN_RST:0,CR2284R1_SWITCH:0,CDT_MSG_FULL_TRACE:0,CR2284R1_COMPATIBLE_SWITCH:1,COMBINE_OPERATION_DRD_SWITCH:1,UL_INTER_PROTECT_SWITCH:1,FAST_DORMANCY_SWITCH:0,SYS_HO_IN_CIPHER_SWITCH:



43



0,PTT_EARLY_TRANS_SWITCH_OFF:0,UPLINK_MDC_ENHENCEMENT_SWITCH:0,NODEB_PRIVATE_INTERFACE_SWITCH:0,PTT_SPEC_LI_SWITCH_OFF:0,RNC_DF_2_URA_PCH_SWITCH:0,FD_TAC_MATCH_SWITCH:0,NONPTT_L1_FAST_SYNC_SWITCH:0,URAPCH_LAYERED_PAGING_RT_SWITCH:0,URAPCH_LAYERED_PAGING_NRT_SWITCH:0,IDLE_LAYERED_PAGING_NRT_SWITCH:0,IDLE_LAYERED_PAGING_RT_SWITCH:0,INTELLIGENT_WIFI_DETECT_AND_SELECTION:0,INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH:0,PTUSER_ID



44



ENTIFY_SWITCH:0



45



PROCESSSWITCH

BSC6910 SETURRCTRLSWITCH

WRFD-021102WRFD-150205WRFD-150204WRFD-010101WRFD-150231WRFD-020500WRFD-021303WRFD-020132WRFD-020124WRFD-140206WRFD-020134WRFD-020128WRFD-01061212WRFD-010641WRFD-020806

Cell BarringLayered Pagingin Idle ModePlatinum UserPrioritizing3GPP R9SpecificationsRIM BasedUMTS TargetCell Selectionfor LTEEnhanced FastDormancyIMSI BasedHandoverWeb browsingaccelerationUplink FlowControl of UserPlaneLayered Pagingin URA_PCHPush to TalkQualityImprovementfor SubscribedServiceHSUPA IubFlow Control inCase of IubCongestionHSUPAAdaptiveTransmissionDifferentiatedService Basedon SPI Weight

Meaning:1)INVOKE_TRACE_SWITCH.1: This switch isturned on. RNCwill start InvokeTrace procedureupon receivingINVOKETRACEMessage formCN. 0: Thisswitch is turnedoff. RNC won'tstart the InvokeTrace procedurethough itreceives theINVOKETRACEmessage. 2)SYS_INFO_UPDATE_FOR_IU_RST. 1: Thisswitch is turnedon. The SIB1does not containbroken-downCN information.In this case, theUE will notselect broken-down networkwhen Iutransmissionfailure occurs. 0:This switch isturned off. TheSIB1 containsthe broken-down CNinformation. Inthis case, the UEwill selectbroken-downnetwork but theRNC will reject



46



the request whenIu transmissionfailure occurs. 3)DRNC_DIRECT_DSCR.Whether theDirectedSignalingConnection re-establishment(DSCR)procedure istriggered duringa cell updateover the Iurinterface forUEs that are notin theCELL_DCHstate or for UEsthat are in theCELL_DCHstate and do nothave an Iurconnection. Thisswitch is set onthe drift radionetworkcontroller(DRNC) side. 1:This switch isturned on.DRNC will startDSCRproceduredirectly in RRCstates other thanCELL_DCH orCELL_DCHthat do not havean Iurconnection. 0:This switch isturned off.DRNC willtransfer RRCCELL UPDATEmessage to



47



SRNC. 4)PTUSER_IDENTIFY_ENH_SWITCH(Platinum useridentifyenhancementswitch) Whetherplatinum usersare identified inDRNC orrelocationscenarios. 1:This switch isturned on.Platinum usersare identifiedand theirservices areguaranteed inDRNC orrelocationscenarios. 0:This switch isturned off.Platinum usersare notidentified inDRNC orrelocationscenarios. 5)RNC_SHARE_SWITCH. 1:This switch isturned on. Thetraffic sharingfunction isenabled. 0: Thisswitch is turnedoff. The trafficsharing functionis disabled,service accesswill be affectedunder heavytraffic. 6)RNCAP_IMSI_HO_SWITCH.



48



1: This switch isturned on. Imsihandoverfunction will beused. 0: Thisswitch is turnedoff. Imsihandoverfunction will notbe used. 7)TERMINAL_VERSION_DEBASE_SWITCH.1: This switch isturned on.Terminalversion R4 willdebase to R99.0: This switch isturned off.Terminalversion R4 willnot debase toR99. 8)SYS_HO_OUT_CIPHER_SWITCH. 1: Thisswitch is turnedon. The RNCwill addciphering byte atGSMHANDOVERCOMMAND ifthe GSM systemdo not add anycipherinformation atthat message. 0:This switch isturned off. TheRNC will notadd cipheringbyte at GSMHANDOVERCOMMAND ifthe GSM systemdo not add any



49



cipherinformation atthat message. 9)SYS_HO_CIPHER_CONFIG.1: This switch isturned on. Thecipherconfiguration inthe added cipherbyte in GSMwill be A5/1. 0:This switch isturned off. Thecipherconfiguration isA5/0. 10)BARRED_CELL_FOR_CSDOMAIN_RST. 1:This switch isturned on. Cellwill be baredwhen CSdomain isinvalid. 0: Thisswitch is turnedoff. The CSdomain will bebared when CSdomain isinvalid. It isinvalid IfSYS_INFO_UPDATE_FOR_IU_RST is notchecked. 11)CR2284R1_SWITCH. 1: Thisswitch is turnedon. The RNCperforms theprocessingbased onCR2284R1, thatis, based on thedescription insection 8.6.6.28



50



of Release 5 TS25.331. In thissection, itdescribes thatthe HFN isincreased by onewhen RB setupis accompaniedby a Timing re-initialized hardhandover. 0:This switch isturned off. TheHFN is notincreased by onewhen RB setupis accompaniedby a Timing re-initialized hardhandover. 12)CDT_MSG_FULL_TRACE. 1:This switch isturned on. CDTtrace functionstarts tracingfrom messageRRCCONNECTREQUEST. 0:This switch isturned off. CDTtrace functionstarts tracingfrom messageCOMMON ID.13)CR2284R1_COMPATIBLE_SWITCH.CR2284R1causes thecompatibleproblem. if UEis not consistentwith RNCregardingwhether accept



51



the CR2284R1or not, it willcause theproblem ofstreaming whenUEs arecommunicatingwith each other.So RNC createsthis switch.when it ischecked, RNC isauto-adaptive toaccept theCR2284R1according to UEversioninformation.The principlesthat RNC judgesUE whether toaccept theCR2284R1 areas follows: R5and above UEaccepts the CR;R99/R4 UE, if itreceives theSTART LISTvalue from RBSETUPCOMPLETE,RNC figures thatUE accepts theCR; R99/R4 UE,if it onlyreceives theSTART valuefrom RBSETUPCOMPLETE,RNC figures thatUE does notaccept the CR;when it is notchecked,whether RNCaccept the CR or



52



not is accordingtoCR2284R1_SWITCH. Therelationsbetween thesetwo switchesCR2284R1_SWITCH andCR2284R1_COMPATIBLE_SWITCH are asfollows: 1: Thisswitch is turnedon. RNC is self-compatible, sotheCR2284R1_SWITCH is invalid;0: This switch isturned off. TheCR2284R1_SWITCH is valid.14)COMBINE_OPERATION_DRD_SWITCH. 1:This switch isturned on. RNCwill not rejectthe message RBSETUP CMPwithout the IEactive time. 0:This switch isturned off. RNCwill reject themessage RBSETUP CMPwithout the IEactive time. 15)UL_INTER_PROTECT_SWITCH. 1: Thisswitch is turnedon. RNC will dointegrityprotection check



53



for uplink RRCmessages. 0:This switch isturned off. RNCwill not dointegrityprotection checkfor uplink RRCmessages. 16)FAST_DORMANCY_SWITCH. 1: This switchis turned on.RNC will applyFASTDORMANCYfunction. 0: Thisswitch is turnedoff. RNC willnot apply FASTDORMANCYfunction. 17)SYS_HO_IN_CIPHER_SWITCH. During anincoming GSM-to-UMTShandover, if theRNC cannotobtain a UE'sencryptioncapabilityinformationfrom theRELOC REQmessage: 1: Thisswitch is turnedon. Theencryptionalgorithm that isconfigured forboth the RNCand CN is used.For example, ifthe CN isconfigured withthe encryptionalgorithm UEA1



54



and the RNC isconfigured withencryptionalgorithmsUEA0 andUEA1, then theRNC uses theencryptionalgorithmUEA1. 0: Thisswitch is turnedoff. Defaultconfigured ofencryptedparameter UIA1and UEA0 isused. 18)PTT_EARLY_TRANS_SWITCH_OFF. 1:This switch isturned on. PTTuser will notapply the earlytransmissionfunction. 0: Thisswitch is turnedoff. PTT userwill apply theearlytransmissionfunction. 19)UPLINK_MDC_ENHENCEMENT_SWITCH.This switch hasbecome invalid.20)NODEB_PRIVATE_INTERFACE_SWITCH.1: This switch isturned on. TheNodeB privateinterface datacan be taken tothe NodeBthrough the IUB



55



protocolmessage. 0: Thisswitch is turnedoff. The NodeBprivate interfacedata can not betaken to theNodeB throughthe IUB protocolmessage. 21)PTT_SPEC_LI_SWITCH_OFF.1: This switch isturned on.Special LI(LengthIndicator) willnot be used forPTT user. 0:This switch isturned off.Special LI(LengthIndicator) willbe used for PTTuser. 22)RNC_DF_2_URA_PCH_SWITCH. 1: Thisswitch is turnedon. RNC willsupporttransferring FastDormancy UEfromCELL_DCH orCELL_FACH toURA_PCH. 0:This switch isturned off. RNCwill not supporttransferring FastDormancy UEfromCELL_DCH orCELL_FACH toURA_PCH. 23)FD_TAC_MAT



56



CH_SWITCH.1: This switch isturned on. TheRNC uses TACmatching todeterminewhether to applythe FASTDORMANCYfunction for prefast dormancyUEs. 0: Thisswitch is turnedoff. The RNCapplies theFASTDORMANCYfunction for prefast dormancyUEs of 3GPPRelease 5 orlater. 24)NONPTT_L1_FAST_SYNC_SWITCH. 1: Thisswitch is turnedon. If a UE setsup a non-PTTservice on theDCH, the RNCincludes thePost-verificationperiodinformationelement (IE) in aUu message toinstruct the UEto performconcurrentuplink anddownlinksynchronization. 0: This switchis turned off. If aUE sets up anon-PTT serviceon the DCH, the



57



RNC does notinclude the Post-verificationperiod IE in a Uumessage. TheUE firstperformsdownlinksynchronizationand then uplinksynchronization. 25)URAPCH_LAYERED_PAGING_RT_SWITCH. Whether theRNC allowsLayered Pagingin URA_PCHfor a UEprocessing real-time services. 1:This switch isturned on. TheRNC sendspagingmessages to thecell on which aUE processingreal-timeservices campedrecently and tothe neighboringcells of this cell.The RNC pagesthe UE in theentire UTRANregistration area(URA) onlywhen it does notreceive aresponse fromthe UE. Thissignificantlyreduces thenumber ofpagingmessages on the



58



Uu interface. 0:This switch isturned off. TheRNC directlypages the UE inthe entire URA.26)URAPCH_LAYERED_PAGING_NRT_SWITCH. Whether theRNC allowsLayered Pagingin URA_PCHfor a UEprocessing non-real-timeservices. 1: Thisswitch is turnedon. The RNCsends pagingmessages to thecell on which aUE processingnon-real-timeservices campedrecently and tothe neighboringcells of this cell.The RNC pagesthe UE in theentire URA onlywhen the RNCdoes not receivea response fromthe UE. Thissignificantlyreduces thenumber ofpagingmessages on theUu interface. 0:This switch isturned off. TheRNC directlypages the UE inthe entire URA.27)



59



IDLE_LAYERED_PAGING_NRT_SWITCH.Whether toenable layeredpaging for UEsin the idle statewho willestablish non-real-timeservice. 1: Thisswitch is turnedon. The firstbroadcasts apaging messagein the cell whohas interactedwith the UE forthe last time andits neighboringcells. If the UEcannot be paged,the RNC thenbroadcasts apaging messagein the LAC orRAC area. 0:This switch isturned off. TheRNC directlybroadcasts apaging messagein the LAC orRAC area. 28)IDLE_LAYERED_PAGING_RT_SWITCH.Whether toenable layeredpaging for UEsin the idle statewho willestablish real-time service. 1:This switch isturned on. Firstbroadcasts apaging message



60



in the cell whohas interactedwith the UE forthe last time andits neighboringcells. If the UEcannot be paged,the RNC thenbroadcasts apaging messagein the LAC orRAC area. 0:This switch isturned off. TheRNC directlybroadcasts apaging messagein the LAC orRAC area. 29)INTELLIGENT_WIFI_DETECT_AND_SELECTION.Whether toenableintelligent Wi-Fidetection andselection for theRNC. 1: Thisswitch is turnedon. The RNCsupportsintelligent Wi-Fidetection andselection. 0:This switch isturned off. TheRNC does notsupportsintelligent Wi-Fidetection andselection. 30)INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH.Whether toenable the RIM-



61



based cell loadsharing function(MultipleReport). 1: Thisswitch is turnedon. RIM-basedload sharing canbe achievedbetween UMTSand LTE cells.Upon receivinga load sharingrequest from anLTE cell, aUMTS cellresponds with itsown loadinformation. 0:This switch isturned off.UMTS cells donot support theRIM-based cellload sharingfunction.Therefore,UMTS cells donot respond toload sharingrequests fromLTE cells. 31)PTUSER_IDENTIFY_SWITCH. Whether topreferentiallyguaranteeplatinum usersin terms ofnetwork access,voice quality, orPS service rate.1: This switch isturned on. TheRNC recognizesplatinum usersandpreferentiallyguarantees their



62



user experience.0: This switch isturned off. TheRNC does notrecognizeplatinum usersand does notpreferentiallyguarantee theiruser experience.DisuseStatement:Infuture versions,theRNC_SHARE_SWITCH,TERMINAL_VERSION_DEBASE_SWITCH,CR2284R1_SWITCH,CR2284R1_COMPATIBLE_SWITCH,COMBINE_OPERATION_DRD_SWITCHandUPLINK_MDC_ENHENCEMENT_SWITCHbit field valueunder thePROCESSSWITCH parameterwill be deleted.Although theconfigurationinterface in thisversion supportsdelivery andsynchronizationof the bit fieldvalue, the bitfield value is nolonger internallyused. Instead,the function of



63



RNC_SHARE_SWITCH willbe controlled bytheRncShareSwitch parameter inthe SETUCTRLPLNSHAREPARAcommand.GUI ValueRange:INVOKE_TRACE_SWITCH,SYS_INFO_UPDATE_FOR_IU_RST,DRNC_DIRECT_DSCR,PTUSER_IDENTIFY_ENH_SWITCH,RNC_SHARE_SWITCH,RNCAP_IMSI_HO_SWITCH,TERMINAL_VERSION_DEBASE_SWITCH,SYS_HO_OUT_CIPHER_SWITCH,SYS_HO_CIPHER_CONFIG,BARRED_CELL_FOR_CSDOMAIN_RST,CR2284R1_SWITCH,CDT_MSG_FULL_TRACE,CR2284R1_COMPATIBLE_SWITCH,COMBINE_OPERATION_DRD_SWITCH,



64



UL_INTER_PROTECT_SWITCH,FAST_DORMANCY_SWITCH,SYS_HO_IN_CIPHER_SWITCH,PTT_EARLY_TRANS_SWITCH_OFF,UPLINK_MDC_ENHENCEMENT_SWITCH,NODEB_PRIVATE_INTERFACE_SWITCH,PTT_SPEC_LI_SWITCH_OFF,RNC_DF_2_URA_PCH_SWITCH,FD_TAC_MATCH_SWITCH,NONPTT_L1_FAST_SYNC_SWITCH,URAPCH_LAYERED_PAGING_RT_SWITCH,URAPCH_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_RT_SWITCH,INTELLIGENT_WIFI_DETECT_AND_SELECTION,INTERRAT_LOAD_REPORT



65



_FOR_LTE_SWITCH,PTUSER_IDENTIFY_SWITCHUnit:NoneActual ValueRange:INVOKE_TRACE_SWITCH,SYS_INFO_UPDATE_FOR_IU_RST,DRNC_DIRECT_DSCR,PTUSER_IDENTIFY_ENH_SWITCH,RNC_SHARE_SWITCH,RNCAP_IMSI_HO_SWITCH,TERMINAL_VERSION_DEBASE_SWITCH,SYS_HO_OUT_CIPHER_SWITCH,SYS_HO_CIPHER_CONFIG,BARRED_CELL_FOR_CSDOMAIN_RST,CR2284R1_SWITCH,CDT_MSG_FULL_TRACE,CR2284R1_COMPATIBLE_SWITCH,COMBINE_OPERATION_DRD_SWITCH,UL_INTER_PROTECT_SWITCH,FAST_DORMANCY_SWITC



66



H,SYS_HO_IN_CIPHER_SWITCH,PTT_EARLY_TRANS_SWITCH_OFF,UPLINK_MDC_ENHENCEMENT_SWITCH,NODEB_PRIVATE_INTERFACE_SWITCH,PTT_SPEC_LI_SWITCH_OFF,RNC_DF_2_URA_PCH_SWITCH,FD_TAC_MATCH_SWITCH,NONPTT_L1_FAST_SYNC_SWITCH,URAPCH_LAYERED_PAGING_RT_SWITCH,URAPCH_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_NRT_SWITCH,IDLE_LAYERED_PAGING_RT_SWITCH,INTELLIGENT_WIFI_DETECT_AND_SELECTION,INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH,PTUSER_IDENTIFY_SWITCH



67



DefaultValue:INVOKE_TRACE_SWITCH:0,SYS_INFO_UPDATE_FOR_IU_RST:0,DRNC_DIRECT_DSCR:0,PTUSER_IDENTIFY_ENH_SWITCH:0,RNC_SHARE_SWITCH:1,RNCAP_IMSI_HO_SWITCH:0,TERMINAL_VERSION_DEBASE_SWITCH:0,SYS_HO_OUT_CIPHER_SWITCH:0,SYS_HO_CIPHER_CONFIG:1,BARRED_CELL_FOR_CSDOMAIN_RST:0,CR2284R1_SWITCH:0,CDT_MSG_FULL_TRACE:0,CR2284R1_COMPATIBLE_SWITCH:1,COMBINE_OPERATION_DRD_SWITCH:1,UL_INTER_PROTECT_SWITCH:1,FAST_DORMANCY_SWITCH:0,SYS_HO_IN_CIPHER_SWITCH:



68



0,PTT_EARLY_TRANS_SWITCH_OFF:0,UPLINK_MDC_ENHENCEMENT_SWITCH:0,NODEB_PRIVATE_INTERFACE_SWITCH:0,PTT_SPEC_LI_SWITCH_OFF:0,RNC_DF_2_URA_PCH_SWITCH:0,FD_TAC_MATCH_SWITCH:0,NONPTT_L1_FAST_SYNC_SWITCH:0,URAPCH_LAYERED_PAGING_RT_SWITCH:0,URAPCH_LAYERED_PAGING_NRT_SWITCH:0,IDLE_LAYERED_PAGING_NRT_SWITCH:0,IDLE_LAYERED_PAGING_RT_SWITCH:0,INTELLIGENT_WIFI_DETECT_AND_SELECTION:0,INTERRAT_LOAD_REPORT_FOR_LTE_SWITCH:0,PTUSER_ID



69



ENTIFY_SWITCH:0



70



NBMCacAlgoSwitch

BSC6900 ADDUCELLALGOSWITCHMODUCELLALGOSWITCH

WRFD-010654WRFD-021102WRFD-021104WRFD-010653WRFD-020102WRFD-140223WRFD-020101WRFD-020122WRFD-010202WRFD-020117WRFD-020136WRFD-01061211

128 HSDPAUsers per CellCell BarringEmergency Call96 HSDPAUsers per CellLoadMeasurementMOCN CellResourceDemarcationAdmissionControlMulti-CarrierSwitch offBased on QoSUE State inConnectedMode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)Multi-CarrierSwitch offBased on TrafficLoadAnti-InterferenceScheduling forHSUPA20 HSUPAUsers per Cell

Meaning:Whether to enable thealgorithmsrelated to cellserviceadmission.Selecting aswitch enablesthecorrespondingalgorithm andclearing a switchdisables thecorrespondingalgorithm. 1.CRD_ADCTRL: Whether toenable the creditadmissioncontrolalgorithm. Thecredit admissioncontrolalgorithm isvalid only whenthis switch isturned on andtheNODEB_CREDIT_CAC_SWITCH check boxunder the "CACalgorithmswitch"parameter in the"SETUCACALGOSWITCH"command isselected. 2.HSDPA_UU_ADCTRL:Whether toenable air-interface loadadmissioncontrol



71



algorithm forHSDPA UEswho processuplink servicesover the DCHsand downlinkservices over theHSDPAchannels. Thisswitch does nottake effect forUEs whoprocess uplinkservices over theHSUPAchannels anddownlinkservices over theHSDPAchannels. 3.HSUPA_UU_ADCTRL:Whether toenable air-interface loadadmissioncontrolalgorithm forHSUPA UEswho processuplink servicesover the HSUPAchannels anddownlinkservices over theDCHs. Thisswitch does nottake effect forUEs whoprocess uplinkservices over theHSUPAchannels anddownlinkservices over theHSDPAchannels. 4.MBMS_UU_A



72



DCTRL:Whether toenable air-interface loadadmissioncontrolalgorithm forMultimediaBroadcastMulticastService(MBMS) UEs.5.HSDPA_GBP_MEAS:Whether toenable GBPmeasurementfor HSDPAUEs. TheNodeB reportsthe GBP ofHSDPA UEs tothe RNC onlyafter themeasurement isenabled. 6.HSDPA_PBR_MEAS:Whether toenable providedbit rate (PBR)measurementfor HSDPAUEs. TheNodeB reportsthe PBR ofHSDPA UEs tothe RNC onlyafter themeasurement isenabled. 7.SYS_INFO_UPDATE_FOR_IU_RST:Whether toupdate systeminformation



73



after the Iuinterface resets.The cell barringfunction in theevent of Iuinterface faultscan be enabledonly when thisswitch is turnedon and theSYS_INFO_UPDATE_FOR_IU_RST (RNC-level switch)check box underthe "Processswitch"parameter in the"SETURRCTRLSWITCH" commandis selected. 8.HSUPA_PBR_MEAS:Whether toenable PBRmeasurementfor HSUPAUEs. TheNodeB reportsthe PBR ofHSUPA UEs tothe RNC onlyafter themeasurement isenabled. 9.HSUPA_EDCH_RSEPS_MEAS: Whether toenable theperiodicmeasurement oftotal receivepower generatedby schedulingservices on E-DCHs. 10.EMC_UU_AD



74



CTRL: Whetherto enable poweradmissioncontrol for UEsinitiatingemergency calls.11. Receivedtotal widebandpower_RESIST_DISTURB:Whether toenable anti-inferenceprocessing whenReceived TotalWidebandPower (RTWP)is abnormal. 12.SIGNALING_SHO_UL_AC_SWITCH:Whether toenable uplinkpower-basedsoft handovercontrol for UEswho haveestablished RRCconnections butprocess noservices. If thisswitch is turnedon, such UEscannot accesstarget cells byusing softhandovers if thetarget cells are inthe OLC state inthe uplink. 13.FACH_UU_ADCTRL: Whetherto enableadmissioncontrol for UEsthat establishservices onFACHs. If this



75



switch is turnedon and a UEinitiates an RABor RRCconnectionsetup request(with a causevalue other thanDetach,Registration, orEmergencyCall) in anoverloaded cell,the setup requestis rejected. If thecell is notoverloaded, theFACH useradmissionprocedure isinitiated and theUE can accessthe cell after theproceduresucceeds. If thisswitch is turnedoff, the FACHuser admissionprocedure isinitiatedregardless ofwhether the cellis overloadedand the UE canaccess the cellafter theproceduresucceeds. 14.MIMOCELL_LEGACYHSDPA_ADCTRL:Whether toenableadmissioncontrol forcommonHSDPA UEs inMIMO cells. 15.



76



FAST_DORMANCY_ADCTRL: Whether toenableadmissioncontrol for fastdormancy-capable UEs.This switch isused to alleviateFACHcongestion bydisabling statemigration forfast dormancy-capable UEs inthe CELL-DCHstate. If thisswitch is turnedoff for manycells under theRNC, signalingstorms occurand CPU usageon the RNC,NodeB, andSGSN increasessignificantly,affecting serviceaccess. Thefunctioncorrespondingto this switch hasbeen deleted inR13, and thisswitch is invalid.16.FACH_USER_NUM_NOT_CTRL: Whetherto restrict thenumber ofadmitted UEsthat use FACHsto transmitservice data.



77



GUI ValueRange:CRD_ADCTRL(CreditAdmissionControlAlgorithm),HSDPA_UU_ADCTRL(HSDPA UULoad AdmissionControlAlgorithm),HSUPA_UU_ADCTRL(HSUPA UULoad AdmissionControlAlgorithm),MBMS_UU_ADCTRL(MBMSUU LoadAdmissionControlAlgorithm),HSDPA_GBP_MEAS(HSDPAGBP MeasAlgorithm),HSDPA_PBR_MEAS(HSDPAPBR MeasAlgorithm),SYS_INFO_UPDATE_FOR_IU_RST(SystemInfo UpdateSwitch for IuReset),HSUPA_PBR_MEAS(HSUPAPBR MeasAlgorithm),HSUPA_EDCH_RSEPS_MEAS(HSUPAEDCH RSEPSMeasAlgorithm),



78



EMC_UU_ADCTRL(emergency callpoweradmission),RTWP_RESIST_DISTURB(RTWP ResistDisturb Switch),SIGNALING_SHO_UL_AC_SWITCH(Signaling ShoUl power cacswitch),FACH_UU_ADCTRL(FACHpower cacswitch),MIMOCELL_LEGACYHSDPA_ADCTRL(LegacyHSDPAAdmissionControlAlgorithm inMIMO Cell ),FAST_DORMANCY_ADCTRL(FastDormancy UserAdmissionControlAlgorithm),FACH_USER_NUM_NOT_CTRL(FACHUSERUNLIMITED)Unit:NoneActual ValueRange:CRD_ADCTRL,HSDPA_UU_ADCTRL,HSUPA_UU_A



79



DCTRL,MBMS_UU_ADCTRL,HSDPA_GBP_MEAS,HSDPA_PBR_MEAS,SYS_INFO_UPDATE_FOR_IU_RST,HSUPA_PBR_MEAS,HSUPA_EDCH_RSEPS_MEAS,EMC_UU_ADCTRL,RTWP_RESIST_DISTURB,SIGNALING_SHO_UL_AC_SWITCH,FACH_UU_ADCTRL,MIMOCELL_LEGACYHSDPA_ADCTRL,FAST_DORMANCY_ADCTRL,FACH_USER_NUM_NOT_CTRLDefaultValue:CRD_ADCTRL:1,HSDPA_UU_ADCTRL:0,HSUPA_UU_ADCTRL:0,MBMS_UU_ADCTRL:0,HSDPA_GBP_MEAS:0,HSDPA_PBR_MEAS:0,SYS_INFO_



80



UPDATE_FOR_IU_RST:0,HSUPA_PBR_MEAS:0,HSUPA_EDCH_RSEPS_MEAS:0,EMC_UU_ADCTRL:1,RTWP_RESIST_DISTURB:0,SIGNALING_SHO_UL_AC_SWITCH:0,FACH_UU_ADCTRL:0,MIMOCELL_LEGACYHSDPA_ADCTRL:0,FAST_DORMANCY_ADCTRL:1,FACH_USER_NUM_NOT_CTRL:0



81



NBMCacAlgoSwitch

BSC6910 ADDUCELLALGOSWITCHMODUCELLALGOSWITCH

WRFD-010654WRFD-021102WRFD-021104WRFD-010653WRFD-020102WRFD-140223WRFD-020101WRFD-020122WRFD-010202WRFD-020117WRFD-020136WRFD-01061211

128 HSDPAUsers per CellCell BarringEmergency Call96 HSDPAUsers per CellLoadMeasurementMOCN CellResourceDemarcationAdmissionControlMulti-CarrierSwitch offBased on QoSUE State inConnectedMode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)Multi-CarrierSwitch offBased on TrafficLoadAnti-InterferenceScheduling forHSUPA20 HSUPAUsers per Cell

Meaning:Whether to enable thealgorithmsrelated to cellserviceadmission.Selecting aswitch enablesthecorrespondingalgorithm andclearing a switchdisables thecorrespondingalgorithm. 1.CRD_ADCTRL: Whether toenable the creditadmissioncontrolalgorithm. Thecredit admissioncontrolalgorithm isvalid only whenthis switch isturned on andtheNODEB_CREDIT_CAC_SWITCH check boxunder the "CACalgorithmswitch"parameter in the"SETUCACALGOSWITCH"command isselected. 2.HSDPA_UU_ADCTRL:Whether toenable air-interface loadadmissioncontrolalgorithm for



82



HSDPA UEswho processuplink servicesover the DCHsand downlinkservices over theHSDPAchannels. Thisswitch does nottake effect forUEs whoprocess uplinkservices over theHSUPAchannels anddownlinkservices over theHSDPAchannels. 3.HSUPA_UU_ADCTRL:Whether toenable air-interface loadadmissioncontrolalgorithm forHSUPA UEswho processuplink servicesover the HSUPAchannels anddownlinkservices over theDCHs. Thisswitch does nottake effect forUEs whoprocess uplinkservices over theHSUPAchannels anddownlinkservices over theHSDPAchannels. 4.MBMS_UU_ADCTRL:



83



Whether toenable air-interface loadadmissioncontrolalgorithm forMultimediaBroadcastMulticastService(MBMS) UEs.5.HSDPA_GBP_MEAS:Whether toenable GBPmeasurementfor HSDPAUEs. TheNodeB reportsthe GBP ofHSDPA UEs tothe RNC onlyafter themeasurement isenabled. 6.HSDPA_PBR_MEAS:Whether toenable providedbit rate (PBR)measurementfor HSDPAUEs. TheNodeB reportsthe PBR ofHSDPA UEs tothe RNC onlyafter themeasurement isenabled. 7.SYS_INFO_UPDATE_FOR_IU_RST:Whether toupdate systeminformationafter the Iu



84



interface resets.The cell barringfunction in theevent of Iuinterface faultscan be enabledonly when thisswitch is turnedon and theSYS_INFO_UPDATE_FOR_IU_RST (RNC-level switch)check box underthe "Processswitch"parameter in the"SETURRCTRLSWITCH" commandis selected. 8.HSUPA_PBR_MEAS:Whether toenable PBRmeasurementfor HSUPAUEs. TheNodeB reportsthe PBR ofHSUPA UEs tothe RNC onlyafter themeasurement isenabled. 9.HSUPA_EDCH_RSEPS_MEAS: Whether toenable theperiodicmeasurement oftotal receivepower generatedby schedulingservices on E-DCHs. 10.EMC_UU_ADCTRL: Whether



85



to enable poweradmissioncontrol for UEsinitiatingemergency calls.11. Receivedtotal widebandpower_RESIST_DISTURB:Whether toenable anti-inferenceprocessing whenReceived TotalWidebandPower (RTWP)is abnormal. 12.SIGNALING_SHO_UL_AC_SWITCH:Whether toenable uplinkpower-basedsoft handovercontrol for UEswho haveestablished RRCconnections butprocess noservices. If thisswitch is turnedon, such UEscannot accesstarget cells byusing softhandovers if thetarget cells are inthe OLC state inthe uplink. 13.FACH_UU_ADCTRL: Whetherto enableadmissioncontrol for UEsthat establishservices onFACHs. If thisswitch is turned



86



on and a UEinitiates an RABor RRCconnectionsetup request(with a causevalue other thanDetach,Registration, orEmergencyCall) in anoverloaded cell,the setup requestis rejected. If thecell is notoverloaded, theFACH useradmissionprocedure isinitiated and theUE can accessthe cell after theproceduresucceeds. If thisswitch is turnedoff, the FACHuser admissionprocedure isinitiatedregardless ofwhether the cellis overloadedand the UE canaccess the cellafter theproceduresucceeds. 14.MIMOCELL_LEGACYHSDPA_ADCTRL:Whether toenableadmissioncontrol forcommonHSDPA UEs inMIMO cells. 15.FAST_DORM



87



ANCY_ADCTRL: Whether toenableadmissioncontrol for fastdormancy-capable UEs.This switch isused to alleviateFACHcongestion bydisabling statemigration forfast dormancy-capable UEs inthe CELL-DCHstate. If thisswitch is turnedoff for manycells under theRNC, signalingstorms occurand CPU usageon the RNC,NodeB, andSGSN increasessignificantly,affecting serviceaccess. Thefunctioncorrespondingto this switch hasbeen deleted inR13, and thisswitch is invalid.16.FACH_USER_NUM_NOT_CTRL: Whetherto restrict thenumber ofadmitted UEsthat use FACHsto transmitservice data.GUI ValueRange:CRD_A



88



DCTRL(CreditAdmissionControlAlgorithm),HSDPA_UU_ADCTRL(HSDPA UULoad AdmissionControlAlgorithm),HSUPA_UU_ADCTRL(HSUPA UULoad AdmissionControlAlgorithm),MBMS_UU_ADCTRL(MBMSUU LoadAdmissionControlAlgorithm),HSDPA_GBP_MEAS(HSDPAGBP MeasAlgorithm),HSDPA_PBR_MEAS(HSDPAPBR MeasAlgorithm),SYS_INFO_UPDATE_FOR_IU_RST(SystemInfo UpdateSwitch for IuReset),HSUPA_PBR_MEAS(HSUPAPBR MeasAlgorithm),HSUPA_EDCH_RSEPS_MEAS(HSUPAEDCH RSEPSMeasAlgorithm),EMC_UU_ADCTRL



89



(emergency callpoweradmission),RTWP_RESIST_DISTURB(RTWP ResistDisturb Switch),SIGNALING_SHO_UL_AC_SWITCH(Signaling ShoUl power cacswitch),FACH_UU_ADCTRL(FACHpower cacswitch),MIMOCELL_LEGACYHSDPA_ADCTRL(LegacyHSDPAAdmissionControlAlgorithm inMIMO Cell ),FAST_DORMANCY_ADCTRL(FastDormancy UserAdmissionControlAlgorithm),FACH_USER_NUM_NOT_CTRL(FACHUSERUNLIMITED)Unit:NoneActual ValueRange:CRD_ADCTRL,HSDPA_UU_ADCTRL,HSUPA_UU_ADCTRL,MBMS_UU_A



90



DCTRL,HSDPA_GBP_MEAS,HSDPA_PBR_MEAS,SYS_INFO_UPDATE_FOR_IU_RST,HSUPA_PBR_MEAS,HSUPA_EDCH_RSEPS_MEAS,EMC_UU_ADCTRL,RTWP_RESIST_DISTURB,SIGNALING_SHO_UL_AC_SWITCH,FACH_UU_ADCTRL,MIMOCELL_LEGACYHSDPA_ADCTRL,FAST_DORMANCY_ADCTRL,FACH_USER_NUM_NOT_CTRLDefaultValue:CRD_ADCTRL:1,HSDPA_UU_ADCTRL:0,HSUPA_UU_ADCTRL:0,MBMS_UU_ADCTRL:0,HSDPA_GBP_MEAS:0,HSDPA_PBR_MEAS:0,SYS_INFO_UPDATE_FOR_IU_RST:



91



0,HSUPA_PBR_MEAS:0,HSUPA_EDCH_RSEPS_MEAS:0,EMC_UU_ADCTRL:1,RTWP_RESIST_DISTURB:0,SIGNALING_SHO_UL_AC_SWITCH:0,FACH_UU_ADCTRL:0,MIMOCELL_LEGACYHSDPA_ADCTRL:0,FAST_DORMANCY_ADCTRL:1,FACH_USER_NUM_NOT_CTRL:0



92



IuAcIntervalOf-Cell

BSC6900 SETUACALGO

WRFD-021102 Cell Barring Meaning:Whenthe Iu interfaceis faulty, theRNC graduallyrestricts cellaccess in Barmode. When theIu interface isrestored, theRNC graduallyenables cellaccess in NotBar mode. Thisparameterdefines theinterval betweenthe cellsworking in Barmode or in NotBar mode. Inthis way, thelocation updateprocedure canbe distributed toa specified timeperiod and therisk due tocongestion isreduced.GUI ValueRange:1~3600Unit:sActual ValueRange:1~3600Default Value:1



93



IuAcIntervalOf-Cell

BSC6910 SETUACALGO

WRFD-021102 Cell Barring Meaning:Whenthe Iu interfaceis faulty, theRNC graduallyrestricts cellaccess in Barmode. When theIu interface isrestored, theRNC graduallyenables cellaccess in NotBar mode. Thisparameterdefines theinterval betweenthe cellsworking in Barmode or in NotBar mode. Inthis way, thelocation updateprocedure canbe distributed toa specified timeperiod and therisk due tocongestion isreduced.GUI ValueRange:1~3600Unit:sActual ValueRange:1~3600Default Value:1



94



DomainType BSC6900 ADDURNCALLCELLBLKMODURNCALLCELLBLK

WRFD-021102 Cell Barring Meaning:Thisparameterspecifies theblocked domaintype.GUI ValueRange:PsBlk(BLOCK PS),CsAndPsBlk(BLOCK CSAND PS)Unit:NoneActual ValueRange:PsBlk,CsAndPsBlkDefaultValue:None

DomainType BSC6910 ADDURNCALLCELLBLKMODURNCALLCELLBLK

WRFD-021102 Cell Barring Meaning:Thisparameterspecifies theblocked domaintype.GUI ValueRange:PsBlk(BLOCK PS),CsAndPsBlk(BLOCK CSAND PS)Unit:NoneActual ValueRange:PsBlk,CsAndPsBlkDefaultValue:None



95



ProcessDuration BSC6900 ADDURNCALLCELLBLKMODURNCALLCELLBLK

WRFD-021102 Cell Barring Meaning:Thisparameterspecifies theprocessingduration of thecell blocking inthe RNC. TheRNC blockscells one by onewithin theduration.GUI ValueRange:2~30Unit:minActual ValueRange:2~30DefaultValue:None

ProcessDuration BSC6910 ADDURNCALLCELLBLKMODURNCALLCELLBLK




96



DomainType BSC6900 ADDUCELLACCESSSTRICTMODUCELLACCESSSTRICT

WRFD-021102 Cell Barring Meaning:Whether the PS domainof a cell isblocked.GUI ValueRange:NoneBlk, PsBlkUnit:NoneActual ValueRange:NoneBlk, PsBlkDefaultValue:NoneBlk

DomainType BSC6910 ADDUCELLACCESSSTRICTMODUCELLACCESSSTRICT

WRFD-021102 Cell Barring Meaning:Whether the PS domainof a cell isblocked.GUI ValueRange:NoneBlk, PsBlkUnit:NoneActual ValueRange:NoneBlk, PsBlkDefaultValue:NoneBlk



97



ProcessDuration BSC6900 ADDUCNOPALLCELLBLKMODUCNOPALLCELLBLK


ProcessDuration BSC6910 ADDUCNOPALLCELLBLKMODUCNOPALLCELLBLK




98

7 Counters

There are no specific counters associated with this feature.

WCDMA RANCell Barring Feature Parameter Description 7 Counters


99

8 Glossary

For the acronyms, abbreviations, terms, and definitions, see Glossary.

WCDMA RANCell Barring Feature Parameter Description 8 Glossary


100

9 Reference Documents

None

WCDMA RANCell Barring Feature Parameter Description 9 Reference Documents


101

Cell Barring(RAN15.0 02)

Documents

Transcript of Cell Barring(RAN15.0 02)