CD711T/TJ USER Manual

SAFETY AND CLEANING Safety

■ This device is designed for the play-back of audio signals.Any other use is

expressly prohibited.

■ Protect the device from moisture (water drops or splashes), direct sunlight and

heat.

■ Do not place any vessels such as vases on the device.

■ Only use the device in a moderate climate.

■ Do not place any objects such as burning candles on the device.

■ Please note when deciding where to put the device that furniture surfaces are

covered by various types of lacquer and plastic, most of which contain chemical

additives. These may cause corrosion to the feet of the device, thus resulting in

stains on the surface of the furniture which can be difficult or impossible to remove.

■ The device contains self-lubricating bearings, which must not be oiled or greased.

■ Condensation may form on the lens if the device is taken into a warm room from

the cold. This prevents if from playing a Disc.

■ Never touch the lens on the device. Always keep the disc compartment closed to

prevent dust from collecting on the lens.

■ Only operate the device with the power supply provided.

■ Never open the device casing. No warranty claims are accepted for damage

resulting from improper handling.

■ Note, prolonged listening at loud volumes with the earphones can damage

your hearing.

Cleaning ■ If the device is unable to scan discs perfectly, use a standard, commercially

available cleaning CD to clean the laser optics. Other cleaning methods may

damage the laser optics.

- 1 -

■ Clean the device with a clean, damp leather cloth. Do not use any cleaning

agents.

■ WARNING: The batteries (battery pack or batteries installed) shall not be

exposed to excessive heat such as sunshine, fire or the like.

OVERVIEW

- 2 -

Buttons and controls

OVERVIEW The display

CD A CD-DA has been inserted.

MP3 An MP3 CD has been inserted.

Displays the total number of title or the current track(CD-DA).

Model No. Mark Descriptions

1 HOLD Lock button switch.(Not power switch button)

2

Starts and pauses play back.（Make sure the “HOLD” button turned at “OFF” position before powering on）

3

Press once to replay the current song ,Short press twice to select previous song ,Long Press to fast backward

4 Short press to select the next song; Long press to fast forward

5 Press once, ends playback; press twice switches the device off

6

Selects sound effects

7 MODE Selects several playback options

8 ASP Switches the anti-shock system on/off

9 DIR Select the next album, only for MP3 format

10 LCD LCD Display

11 OPEN Opens the CD lid

12 PHONES Headphone jack for connecting a headphone set with a jack plug(Ø3.5mm)

13 USB 5V Charging input

14 VOL- /VOL+ Adjusts the volume

15 RESET The reset hole

- 3 -

Displays the total playing time or the elapsed playing time of the title

(CD-DA).

Displays the total number of albums or the current album.

Displays the elapsed playing time of the file (MP3).

DIR All the files of the current album are played back repeatedly(MP3).

PGM A track memory is created or played back.

SHUF All files or tracks are played back in random order.

INTRO The first ten seconds of each title or file are played.

ASP The anti-shock system has been activated.

BBS The Bass Boost system has been activated.

POP JAZZ Shows the selected sound effect.

The ”Volume restriction” is switched off.

1 A file or a track is repeated.

All tracks on the MP3 CD or all files on the CD-DA are replayed.

Informed about the state of the batteries.

POWER SUPPLY Mains operation (with mains adapter) Notes: ■ Check if the mains voltage on the mains adapter type plate corresponds to your

local mains supply.

■ The only way to disconnect the device from the mains supply is to unplug the

adapter.

■ Only unplug the mains adapter from the socket when you are not from the

socket when you are not using the device.

1、Plug the mains adapter cable into the>> DC IN 4.5V <<socket.

2、Plug the mains adapter into the mains socket.

- 4 -

Caution: ■ Only operate the device with the power supply provided.

Environmental note: ■ Batteries, including those which contain no heavy metal, should not be disposed

of with house hold waste. Please dispose of used batteries in an environmentally

responsible manner. Find out about the legal regulations which apply in your area.

GENERAL INFORMATION Connecting earphones 1 Connect the earphones to the >> << socket （ 3.5mm）.

Notes:

Excessive volume can be hazardous to yourself and other road users. Listen at

a volume which still allows you to hear outside noises clearly, for instance horns,

emergency vehicles and police cars.

The output of the device guarantees the best possible sound at medium volume.

Prolonged listening at loud volumes can damage your hearing.

Switching on / off the key-lock 1. Switch on the key-lock by moving the slider >> << to the

position >> <<.

-The keys on the device are locked and LCD will display “HOLD”.

2. Switch off the key-lock by moving the slider >> << to the

position >> <<.

Adjusting the volume

1. Adjust the volume with >> <<.

- 5 -

Switch off the volume restriction To protect your hearing, after switching on the device, only reduced volume is

available. You can switch off this “Volume restriction”.

1 >> << press and hold.

-- Display: >> << flashes for 5 seconds.

2 Switch off the “Volume restriction” with >> <<.

Note:

The volume restriction is reactivated after switching off or changing the disk.

Sound effects During playback you can choose between the following sound effects: Flat (no

display), BBS, Pop, Jazz, Rock, Classic.

Select the sound effects by short pressing>> <<.

Note:

CD611TA can not support “Sound effects”.

How to connect Bluetooth Before the CD player connects to the Bluetooth speaker, make sure that your Bluetooth speaker is not connected to other devices. 1, Put CD disc in your CD player and connect power through adapter or 2 x “AA”

battery (not included).

2, Click ： to start playing the CD

3, Power on your BT device and turn it into pairing mode (please make sure your

device has enter to pairing mode and waiting BT connection, otherwise CD player

could not connect it)

4, Long Press Play MODE key on CD, symbol will shows in the LCD display.

Then CD player will try to pairing with your BT device automatically.

5, When CD player had paired with your BT device, you will hear the music from your

BT device.

- 6 -

Notes :

1) Pairing lead time would be around 15-50 second

2) When using BT mode, please make sure the wire earphone is unplugged.

3) CD player only can pair with one BT device at a time. If there is more than one

Bluetooth device around the CD player, it may randomly pair one of them.

BASIC FUNCTIONS Inserting a disc

1 Press the >> << sliding switch to the right and open the CD lid.

2 Insert the disc with the label facing upwards and gently push the centre of the disc to latch it into place.

3 Close the CD compartment.

Removing the disc

Note:

Press >> <<before you open the CD compartment.

1 Press the >> << sliding switch to the right and open the CD lid.

2 Remove the disc.

3 Close the CD compartment.

CD playback

The device automatically recognizes the type of disc inserted (CD-DA, CD-R,

CD-RW, MP3 CD).

1 Press>> << to switch on the device.

--Playback of the disc inserted starts automatically. It begins with the first track or

file.

--Display: briefly displays the total number of files, albums or tracks and then the

number of the first file or track and the elapsed playing time.

- 7 -

BASIC FUNCTIONS 1 Use >> << to switch to playback pause.

-- Display: the playing time of the file or track flashes.

2 Continue playback with >> <<.

3 Press>> << to end playback.

4 To switch off the device, press >> <<again.

Notes: Playback stops automatically when the end of the disc is reached, if the CD

compartment is opened or if the batteries run out.

The device switched off automatically after the end of playback if you do not

press a button within 30 seconds.

Resume function

1 End playback by pressing>> << twice.

-- When playback is resumed, it starts from the position at which it was ended.

2 To start playback of the first track, press>> << once and start playback

with >> <<.

Searching for a passage within a file or track

1 During playback, press>> << or >> << and hold it down until you find the

passage you want to hear.

-- During the search the volume is reduced.

Selecting another file or track

1 During playback, keep pressing >> << or >> << briefly until you see the

number of the file or track you want in the display.

-- Playback of the selected track starts automatically. - 8 -

Selecting albums (only MP3)

1 During playback, press>> << repeatedly until the number of the desired

album appears in the display.

-- Playback begins with the first file of the selected album.

ADDITIONAL FUNCTIONS Note:

All additional functions except for “ Creating a track memory” can be exited by

pressing >> << repeatedly.

Repeating a file or track

1 During playback, press >> << once.

-- Display: >> << , the file or track is played back repeatedly.

Repeating all files or titles

1 During playback, press>> << until >> << appears in the display.

-- All files or tracks are played back repeatedly.

Repeating all the files on an album (only MP3)

1 During playback, press>> << until >> << appears in the display.

-- All the files in an album are repeated.

Playing the introductions of tracks or files on the disc (Intro)

1 During playback, press>> << so often until >> << flashed in the

display.

2 To start this function, press>> <<.

-- The first seconds of each track are played.

- 9 -

3 To play back the whole of the current track, press>> <<again.

Playing back files or tracks in random order (Shuffle)

1 During playback, press>> << so often until >> << flashes in the

display.

2 To start this function, press>> <<.

-- All of the tracks on the disc are played back in random order.

ADDITIONAL FUNCTIONS_________________ Creating a track memory

This function enables you to save up to 64 tracks or files on the current disc in a

particular order and then play them back.The same track may be stored more

than once.

1 Insert the disc and press >>■<< after start playback.

2 Press >>MODE<< to call up the function.

-Display:>> PGM <<flashes.

3 Select the desired album with >> DIR << ( only MP3).

4 Select the desired file or track by pressing >> << or>> <<.

5 Save the file or track by pressing >> <<.

Notes: ■To store more files o r tracks, repeat steps 3 or 4 to 5. ■If you try to store more than 64 files or tracks,the first track you saved is displayed. Playing back a track memory 1 Start the track memory by pressing >> <<.

-Display: playback begins with the first programmed file or track

- 10 -

2 End playback of the track memory With >>■<<.

3 To play the track memory again, press >> << and afterwards >> <<.

Deleting the track memory 1 In Stop mode, press or open the CD compartment.

Note: ■The track or file memory is also deleted if the mains adapter is disconnected or if

the batteries are removed from the device.

Digital anti-shock system(DAS) The anti-shock system reads the data on the CD-DA 40 seconds in advance (or 120

seconds in MP3 mode). DAS ON=memory used for reducing battery consumption

(CD stops after a while ).DAS OFF=optimum anti-shock performance,memory is

constantly loaded. You cannot switch off the antishock system in MP3 mode.

press >>ASP<< to switch the anti-shock system on or off.

- 11 -

CD 随身听用户手册（HC22）

尊敬的客户： 感谢您选择鸿福泰电子科技有限公司出品的便携式 HC22 播放器 HC22 独特的降噪、抗击防震系统处理技术以及专配的机芯，兼容 CD-R、CD-RW，

让您在享受便捷的同时更能得到稳定的播放感受。 在此祝您使用愉快，在使用前请仔细阅读本使用手册并妥善保管好此手册， 以便您的使用。

- 1 -

安全注意事项: 1. 在设置音量时要小心防止过度的输出功率，以免损伤您的听力 2. 别让本系统接触湿气，雨水，沙或各种热源，设备上也不可放置花瓶一类盛装液

体的物品 3. 清洁时请使用微湿的软布清洁本设备，切勿用酒精，苯溶剂清洁 4. 长期不使用时请关闭本设备的总电源开关 5. 在任何情况下请不要自行修理本设备，这样会导致保修作废

注意事项 本节内容是为了使用者正确使用播放器,确保播放器性能良好而设,

请认真阅读并遵守。

切勿严重撞击主机。 切勿接触苯、稀释剂等化学物品。 请不要靠近强磁场、电场。 请避开直射光线或发热器具。 切勿将电池加热或丢入火中 切勿自行拆卸、修理、改造。 骑车、驾驶汽车及摩托车时，请勿使用播放器及耳机，以免造成危险。 切勿以较大音量收听，以免对听力造成不良影响。 废弃包装、电池、旧电子产品，请分类妥善处理。 - 2 -

机器功能简介：

1、USB 充电输入端 2、耳机接口 3、停止/关机键

4、EQ 音效选择/加大音量选择 5、M/ 循环模式/蓝牙键 6、显示屏

7、开机/播放/暂停键 8、下一曲按键 9、上一曲按键

10、ASP CD 碟防震功能开关 11、DIR MP3 格式碟片曲目录选曲

12、HOLD 按键锁定开关 13、音量控制开关 14、OPEN 开仓开关

15、复位孔

- 3 -

按键功能简介

：

- 关机状态下，第一次按为开机，停止状态下按一次为播放。

- 播放状态下，按一次为暂停。

：

- 在播放状态下按一次为停止功能。

- 在停止状态按一次为关机。（如在停止状态 30 秒没操作自动关机）

：

- 按一次往前跳一曲，

- 长按此键单曲进入快播状态。

：

- 按一次跳到本曲重头播放，再按一次往后跳一曲，

- 长按此键单曲进入快后退状态。

：EQ 音效选择和加大音量选择

一、HC22，带 EQ 音效选择，带加大音量选择，操作如下：

1、EQ 音效选择：每按一次出现一种状态：（BBS）→（POP）→（JAZZ）→（ROCK）

→（CLASSIC）→（回原状态）。

2、加大音量选择：长按此键显示会跳出 HIGH 字样再按一次音量会随着变大。

注：此功能主要是为保护耳朵而设置的声压要求。

二、HC22J，带 EQ 音效选择，不带加大音量选择，操作如下：

EQ 音效选择：每按一次出现一种状态：（BBS）→（POP）→（JAZZ）→（ROCK）

→（CLASSIC）→（回原状态）。

- 4 -

M/ :

1.连续按下 M/ ，将依续出现“(1)→(ALL)→(INTRO)→(SHUF)→（回原状态）”

-（1）单曲循环播放。

- ALL 全部循环播放。

- INTRO 浏览播放。

- SHUF 任意顺序播放

要解除任意放音时，请反复按下 M/ ，直到显示窗里没有任何放音模式显示。

※ 注意：在任意播放中，不能用按下或回到前后一支曲子

2.连接蓝牙

CD 播放器连接蓝牙音箱前，请确保您的蓝牙音箱未与其它设备相连

2.1 先打开蓝牙音箱,蓝牙音箱必需先进入配对模式状态,在 CD 机开机读碟状态

（注：CD 机与外部蓝牙设备连接配对时必须拔出耳机）,长按 M/ 键 1-3 秒,出现 图

标, 等待 15-50秒钟左右，会自动与周围打开的蓝牙耳机或蓝牙音响配对连接。长按

M/ 键可以切换实现重新连接或断开蓝牙发射功能。

3.自动回连功能

3.1 在 CD 和蓝牙音箱连接时,连接过一次后,断开蓝牙音箱电源,再打开蓝牙音箱

电源,需要 15-30 秒左右,可以自动回连。当蓝牙音箱超出连接距离自动断开后,再走

近距离 10 米范围之内可以自动连接蓝牙功能.

4.耳机与蓝牙切换

CD 机和蓝牙音响连接播放音乐时, 当插入耳机接听音乐，此时蓝牙音响音源会自

动切断,当拔出耳机后,音响音源可继续传输播放.

: 防震键，CD 状态根据使用选择是否要防震。

- CD 防震 45 秒，

- MP3 碟 120 秒。

- MP3 碟播放软件强制防震。 - 5 -

: MP3 碟片曲目区选择播放。

此功能 MP3 碟才有作用，因为 MP3 碟容量大曲目多可选择曲目单元播放。

此功能 CD 碟无作用。

HOLD: 按键锁定开关.打到 ON 位置为锁键，打到 OFF 位置为开锁键。打到 ON 位置，锁键

后按其它按键没作用，只有按 键会跳出 HOLD 界面， 按键没作用。

※注意：锁键时按开机时会跳出 HOLD 字样后消失。可能会误会机器无法开机。

VOLUME +/-：音量控制开关

CD 播放及功能使用方法

接好外置电源适配器或使用电池装好后，打开 OPEN 开关取出光头保护纸片。将碟

片正确压到光头扣位上合上 CD 盖。按 PLAY 键开机，开机后机器会进入读碟状态后

显示总曲目和播放总时间，即可播放音乐。

重要警告：

有裂纹的光碟可能导致播放器故障，因此请勿使用，如果光碟的信号面存在严重划痕，

指纹和污垢等物可能导致本产故障同时会缩短激光头读碟的使用寿命，光碟勿贴标

签，留有透明胶或租赁 CD 标签痕迹的光碟以及标签出糊状物的光碟不可使用。

规格参数：

电源输入 ：USB ----5V 1A

输出功率：20MW (32 欧 双声道)

播放支持碟片：CD 原版碟, MP3 碟 ，CD-R CD-RW 音乐格式刻录碟

发射距离：10 米

- 6 -