catalogo mfhf en - INVELCO · The MD-200-E módem is the lastest development ... The operation...

EQUIPMENT AND SYSTEMS FORRADIO COMMUNICATIONS

C A T A L O G U E

VHF

INVELCO S.A.

INVELCO S.A.Ronda de Poniente 15, 28760 Tres Cantos, Madrid (SPAIN)

Tel. (+34) 918 032 444 Fax. (+34) 918 033 228

Web: www.invelco.com

e-mail: [email protected]

INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES

All Rights reserved. Under the copyright laws, this publication may not be reproduced or transmitted inany form, electronic or mechanical, including pohotocopying, recording, storing in an information retrievalsystem, or translating, whole or part, without prior consent of INVELCO S.A..No responsability is assumed by the use of the information contained in this catalogue. Although allpossible precautions have been taken in the preparation of this catalogue, INVELCO S.A. is not

responsible of any possible mistakes or omissions. Due to constant technical advance of INVELCOS.A., the characteristics of the equipment included in this catalogue may be modified without previousnotice.

and INVELCO, are trademarks property of INVELCO S.A. Other bands and/or commercialproducts that appear in this publication are trademarks or trade names of their respective companies.

® 1998 INVELCO S.A. All Rights reserved.

PRODUCT CATALOGUE

-25

CONNECTION FROMANTENNA TO A VHFTRANSCEIVER

VHF BANDPASSDIPLEXER FILTER

Equipment assigned to allow the operation of a duplex transceiver with a single antenna.

It's a passive device that isolates the reception transmission in more than 60dB. avoidingtherefore the intermodulation between them.

- S.W.R. BETTER THAN 1,2

- 100W MAXIMUM POWER.

- NUMBER OF INPUT/OUTPUTS: 3

- REBOUND BETWEEN INPUTS BETTER THAN 60DB.

- PASSIVE EQUIPMENT.

- NO CONTROL NEEDED.

- NO POWER SUPPLY NEEDED.

IMPORTANT SPECIFICATIONS :

VHF BANDPASS DIPLEXERMOD. AS7396

INVELCO S.A.INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES

INVELCO S.A.

Page 5-26

TECHNICAL CHARACTERISTICS OF THE PASSBAND DIPLEXERMODEL AS-7396

TECHNICAL SPECIFICATIONS

Maximum power supply: ...................................... 100W.

Input and Output impedance: .............................. 50 Ohm.

Input connectors: ................................................. N Female

Output connectors: .............................................. N Female

Inputs/Outputs numbers: ..................................... 3

Operation frequency: ........................................... 150 to 170MHz.

Tx-Rx separation: ................................................. 3,2MHz.

Bandwidth: ........................................................... 2MHz.

Insertion Losses: ................................................. 1dB. typical

Tx / Rx Rejection: ................................................. >60dB.

S.W.R.: ................................................................. <1,2

Measurements:Height: ................................................................. 178 mmWidth: .................................................................. 482.50mmDepth: .................................................................. 400 mm

Weight: ................................................................ 8 Kg.

27

CONNECTION OF ATRANSMITTER ANTENNA TOTWO VHF TRANSMITTERS

HIGH Q CAVITY

Equipment assigned to allow the operation of two VHF transmitters in different frequencieswith a single antenna. It's design is based in Q high cavities and ferrite circulators

It's a pasive device that isolates transmitter from another in more than 70dB. avoidingtherefore the intermodulation between them.

- S.W.R. IN ALL INPUTS BETTER THAN 1,4

- 100W MAXIMUM POWER.

- NÚMBER OF INPUTS: 2

- NUMBER OF OUTPUTS: 1

- REBOUND BETWEEN INPUTS BETTER THAN 70DB.

- PASSIVE EQUIPMENT.

- NO CONTROL NEEDED.

- NO POWER SUPPLY NEEDED


VHF Tx COMBINERMOD. AS7746


INVELCO S.A.

Page 5-28

TECHNICAL CHARACTERISTICS OF THE Tx COMBINERMODEL AS-7746

TECHNICAL SPECIFICATIONS:

Maximum power: .................................................. 100W.

Output power: ...................................................... Input powers added

Input and Output impedance: .............................. 50 Ohm.

Input connectors: ................................................. N Female

Output connectors: .............................................. N Female

Number of inputs: ................................................ 2

Number of outputs: .............................................. 1

TX1-TX2 Operating frequency: ........................... 134 to 175MHz.

F1-F2 minimum separation: .................................. 300KHz.

Insertion loss of an output entry: ........................ 2,5dB.

Rebound between inputs: .................................... >70dB.

S.W.R..: ................................................................ <1,4

Measurements:Height: ................................................................. 185 mmWidth: .................................................................. 482.50mmDepth: .................................................................. 400 mm

Weight: ................................................................ 5 Kg.

29


- OPTIMUM EFFICIENCY IN ALL THE BAND.- ENCAPSULATED IN HIGH RESISTANCE FIBER GLASS.- SUPPORT OF GREAT HARDINESS AND EASY INSTALLATION.- MAXIMUM RELIABILITY AND DURATION.- RADIANT ELEMENT TO LAND FOR TRANSCEIVER PROTECTION.- NULL TUNING IN TIME

- RESISTANT TO WINDS HIGHER TO 250 KM/H.- MAXIMUM OPERATING POWER 150W.- R.O.E. ≤ 1.5

COLINNEAL ANTENNAENCAPSULATED INGLASS FIBER.

FREQUENCY RANGE OF138 UP TO 174 MHz.

This antenna of very easy installation is the ideal complement for fixed radiocomunicationequipment that uses the VHF band. The absence of mobile tuning elements or of commutation,insure that the tuning in time before a frequency exchange is null, what allows to assurethat this antenna is the better solution for systems of type scaner or A.L.E. in those whichis of vital importance, the absence of tuning in times.

138-174 MHz. 150W ANTENNA.AV-138-A


Spanishfabrication

INVELCO S.A.

Page 4-30

ELECTRICAL SPECIFICATIONS.Antenna type................................................................................Colinneal.Operating power ........................................................................... 150 W.Nominal impedance ...................................................................... 50 ohms.R.O.E. .........................................................................................≤1.5Bias .............................................................................................Vertical.Radiation ......................................................................................Omnidirectional.

ESPECIFICACIONES.Frequency range .......................................................................... 138 to 174 MHz.Gain ............................................................................................. 0 dB.Bandwidth .................................................................................... 6 MHz.Speed of the wind ......................................................................... 150Km/h.Length .......................................................................................... 1,80 m.Weight ......................................................................................... 1.8 Kg.Mounting ..................................................................................... 35 to 65 mm. diameter of the

mast.RF connector ............................................................................... N - Female

ANTENNA AV-138-B TECHNICAL SPECIFICATIONS

VHF ANTENNA TECHNICAL CHARACTERISTICS.

MODEL AV-138-A

31


SpanishProduction

VHF FILTER CHANNEL 16MODEL FL-016-A

VHF CHANNEL 16 SELECTIVEFILTER


- OPERATING FREQUENCY 156.800MHZ. - BAND WIDTH 25KHZ. - PASSBAND FILTER. - QUARZ CRYSTAL FILTER.

Selective crystal filter for VHF channel 16. To place in the reception input and protect theequipment from transmission signals in adjacent channels.

INVELCO S.A.

Page 5-32

TECHNICAL CHARACTERISTICSMODEL FL-016-A

Operation frequency ............................. 156.800MHz.Bandwidth ............................................. 25KHz.Input impedance ................................... 50Ω.Output impedance ................................. 50Ω.Type of filter .........................................Bandpass.Insertion loss ........................................ -6.19dB.Out of band attenuation:

±50KHz. ................... -54dB.±100KHz. ................. -64dB.Frequencies higher than ±100KHz.....>-70dB.

37


SpanishProduction

VHF FILTER CHANNEL 70MODEL FL-070-A

VHF CHANNEL 70 SELECTIVEFILTER


- OPERATION FREQUENCY 156.525MHZ. - BANDWIDTH 25KHZ. - PASSBAND FILTER. - QUARZ CRYSTAL FILTER.

Selective crystal filter for VHF channel 70. To place in the reception input and protect theequipment from transmission signals in adjacent channels.

38

INVELCO S.A.TECHNICAL CHARACTERISTICS

MODEL FL-070-A

Operation frequency ............................. 156.525MHz.Bandwidth ............................................. 25KHz.Input impedance ................................... 50Ω.Output impedance ................................. 50Ω.Type of filter .........................................Bandpass.Insertion loss ........................................ -4.98dB.Out of band attenuation:

±50KHz. ................... -55dB.±100KHz. ................. -70dB.Frequencies higher than ±100KHz.....>-75dB.

17


FabricaciónEspañola

IMPORTANT SPECIFICATIONS:

The MD-200-E módem is the lastest development for the VHF DSC communications. It is tobe used in G.M.D.S.S.It can be installed in a Control Centre in remote Coastal Stations.Its built is supported on modern programmed logic digital technics.

DSC VHF MODEMMODEL MD-200-E

- Control by means of the selective call equipment LS-200-A.- Modem for use of DSC, VHF transmission/reception.- Carrier central frequency: 1.700Hz. ±0,5Hz.- Modulation speed: 1200 Bauds.- Modulation tone: 1.300Hz and 2.100Hz. ±0,5Hz- Symbol Error Rate (SER)> at 0.01 at 0.25 micro V PD

DATA MODEM FOR USE IN DSC,VHF TRANSMISSIONS.

CONTROL THROUGH THESELECTIVE CALL MODELLS-200-A.

G.M.D.S.S. / S.M.S.S.M.

18

INVELCO S.A.CARACTERÍSTICAS TÉCNICAS DEL MODEM DSC VHF

MODELO MD-200-E

DSC MODEM:

- Modem for use of DSC,VHF transmission/reception for G.M.D.S.S.

- Control through LS-200-A.

- Transmission line input impedance ......................................... 600 Ohms.

- Reception line output impedance ............................................ 600 Ohms.

- Transmission line output level ................................................ -30dBm to 0dBm adjustable.

- Reception line input level ........................................................ -30dBm to 0dBm adjustable.

- Type of modulation ................................................................ AFSK.

- Modulation .............................................................................. 1.700Hz. ±400Hz

- Error in frequency ................................................................... ±0,5Hz.

- Automatic management of Pass to Transmission (PTT).

- Modulation tone ...................................................................... 1.300Hz & 2.100Hz ±0,5Hz

- Symbol Error rate (SRE) > a 0.01 a 0.25 micro V PD.

- ITU, CCIR, CEPT/ETS/IMO standards fulfilment.

- Local operation ........................................................................ RS-232-C

- Remote operation .................................................................... Line modem / RS-232-C (incorporated)

GENERAL SPECIFICATIONS:

- Power supply .......................................................................... 220VAC

- Opreation temperature ............................................................ -10ºC. to +50ºC.

- Relative humidity .................................................................... 95%

- Built:

Width ........................... Rack 19''

Height .......................... 1U (44mm.)

Depth ........................... 320mm.

11


SpanishProduction

VHF OPERATION POSITIONSOFTWARE (SW-VHF-C)

The operation position is part of a communication system run by a server that is in charge ofcontrolling the different equipment that form the system. The link between the server and theoperation Position is made through the Ethernet network.

The program can control up to a maximum of 8 telephone lines, 15 VHF Duplex equipment, 10Simplex equipment and supervise the state of 8 Autolink equipment.

At the same time, it allows communication only with one line, with one ship only or with both atthe same time.

Due to its dynamism there can be, simultaneously, up to a maximum of 8 telephone integrationsbetween the subscriber and the ship.

It has an independent time counter per line in the telephone integrations for its later rating. Thecounter has an automatic stop.

It also has an alarm system to tell the opeator, when told so. (Case of navigators warning).

It also has record files of the operations and integrations made.

Communications between simplex and duplex equipment can be made.

It can be connected in as many positions as allowed from the server.

Supervises the connection with the server and the Tx and Rx matrices. It allows Duplex-Relaycommunications.

The receivers monitoring can be distributed in several speakers.

VHF EQUIPMENT CONTROL

TELEPHONE NETWORKINTEGRATION

12

INVELCO S.A.VHF OPERATION POSITION PROGRAM

CANARY ISLANDS

REQUESTS:

The minimum requests for the good operation of the control program in the PC are:

- PC Pentium III or higher, CD-ROM reader, keyboard and mouse.

- 128 Mb RAM (Recommended)

- 2000/NT 4.0(SP5)/XP Operative Windows System

- 1280 x 1024 Screen definition

- Ethernet network card (In the connection with the server)

- RS-232-C Port (PTT per Command)

9


SpanishProduction

VHF COMMUNICATIONS SERVERSOFTWARE (SW-VHF-S)

The VHF Communications System is basically formed by a Server where a software applicationis executed. This application manages and controls the different independent units; TR-450-AVHF Duplex Transceivers, TR-350-A VHF Simplex Transceivers, MT-200-B Audio SwitchMatrices, IT-200-A Telephone Integrated units, etc. It is also formed by one or several ClientsOperation Positions where the radiocommunication operations take place. This operationstake place through a software application.

The Server handles each of the System units by means of an RX-232C Serial Port connection.When you want to stablish a communication with the units located in remote positions, it will benecessary to use Modems or Radiolinks that allow the exchange of RS-323C between theServer and the corresponding units. On the other hand, the Operation Positions, communicatewith the Server through a Local Ethernet Network.

An example with different possibilities of units interconnection is shown in the diagram of figure1.

The Server provides the Operation Positions the possibility of assigning VHF Transceiver units(Simplex and Duplex) to make different radiocommunication operations with such units.

Furthermore, the Server can keep VHF units to be used in other services or systems anothersthan the VHF Communication System itself (for example, G.M.D.S.S.).

10

INVELCO S.A.VHF COMMUNICATIONS SERVER PROGRAM

Figure 1

3


SpanishProduction


ONE PORT RS-232-C TO SIXPORTS RS-232-C.

MULTICON REMOTE-CONTROLLERMODEL TM-100-A

- IT ALLOWS THE COTROL IN A REMOTE STATION FROM A RS-232 PORT

TO 6 RS-232 PORTS (1-6).- SPEED CONTROL PORT TO LINE MODEM 115.200 BAUDS.- SPEED OF THE 6 COMMUNICATION PORTS WITH OTHER DEVICES 19.200

BAUDS.- FIFO WRITING AND READING MEMORY, INDEPENDENT IN EACH PORT

(1 - 6).- STATES VISUALIZATION.- POWER SUPPLY 220 VAC ±20%, 50HZ. AND -48VCC.- TEMPERATURE RANGE -20ºC TO +70ºC.- RELATIVE HUMIDITY 95%

Designed to control through modem from one local unit up to 6 INVELCO equipments. Ithas the possibility to extend in modules of 6 units.Aswell as the control of equipments through RS-232-C, it can send 10 orders to the remotestation or receive 10 alarms from that station.

4

INVELCO S.A.MULTICON REMOTE-CONTROLLER TECHNICAL CHARACTERISTICS

MODEL TM-100-A

It allows the INVELCO equipments control in a Remote Station from a RS-232 Port to 6 RS-232 Port (1-6).Speed of the control port to line modem 115.200 bauds.

Speed of the 6 communications ports with other devices 19.200 bauds.

Independent FIFO reading-writing memory in each port (1 - 6).

Remote control: ................. 10 I/O orders.Orders output: ................... open collector.Output capacity ................. 0 to 30Vcc.......................................... Icc= 1A.Orders output through relay:Optional.

Sent from remote: ............. 10 I/O alarms.Alarm signal input: ............ 0 to 2.5Vcc (TTL)........................................... 0 to 25Vcc.Ways of sending alarms: ... automatic.

interrogating.automatic/interrogating.with repetition.

Common RS-232 port connector.RS-232 output ports connectors.

Modular fabrication chassis of 19'' 2U.

Power supply ....... -48Vcc. 220Vac.

Consume ................... 10WTemperature range:-20ºC to +70ºC.Relative humidity: ...... 95%

9


Spanish Production


MARINE BAND VHFTRANSCEIVER EQUIPMENTFOR COASTAL STATIONS.

RS-232 CONTROL BUS.

- FREQUENCY RANGE: 154,4 A 163,75MHZ. - OPERATION MODES: SIMPLEX, SEMIDUPLEX AND DUPLEX. - G3EJN MODULATIONS. - CHANNELING: 25KHZ. (OTHER CHANNELING OPTIONAL) - ALL INTERNATIONAL MARITIME CHANNELS INCLUDED. - USA CHANNELS OPTIONAL. - OPERATION: LOCAL AND REMOTE. - RS-232-C REMOTE CONTROL BUS. - 110/220VAC. POWER SUPPLY. - OTHER POWER SUPPLIES OPTIONAL. - OUTPUT NOMINAL POWER: 50W. - BUILT-UP IN MODULAR WAY EASY TO MAINTAIN. - POSSIBILITY OF REMOTELY CONTROL ALL ITS PATAMETERS. - COMPLETE PROTRECTION AGAINST OPEN ANTENNA OR IN SHORTCIRCUIT.

50W - VHF TRANSCEIVERMODEL TR-650-A

INVELCO S.A.

Page 1-10

GENERAL SPECIFICATIONS :

- Frequency range: ......................... 154.4 to 163.75 MHz.

- All international maritime channels included.

- Channeling: ................................. 25KHz. (other optional)

- Type of Modulation: .................. G3EJN.

- Modes: ........................................ Simplex, Semiduplex & Duplex

- Frequency stability: .................... 1ppm.

- Remote control: ........................... RS-232-C Bus.

- Completely digital design except for part of the power.

- Channels used in U.S.A.: ............. Optional.

TRANSMITTER :

- Output power: ............................ 50W. ±1dB.

- Reduced power: ........................... W/2; W/4; 1W.

- Output impedance: ...................... 50 ohms.

- Better harmonics supression: ...... 70dB.

- Frequency deviation: ................... ±5KHz.

- Spurios radiation: ........................ better -80dB.

- Audio response: .......................... 300 to 3.000 Hz.

- Pre-emphasis: .............................. 6dB/eighth - 750μs.

- Distortion: ................................... less than 5%

- Independent audio input: ............ Microphone.

Line 600Ω.

Data (line 600Ω).

- Audio compressor: ...................... Included.

- Modulation input level: ............... -30dBm. -0dBm.

- Smaller distortion: ....................... 5%

- Better S/N relation: ...................... 50dB

TECHNICAL CHARACTERISTICS OF THE 50W VHF TRANSCEIVER

MODEL TR-650-A

RECEIVER :

- Input Impedance: ........................ 50 ohms.

- Sensitivity: .................................. -0.25μV for 12dB SINAD.

- Speaker audio output power: ...... 5W.

- Line output: ................................. 600Ω. -40dBm. to 0dBm.(adjustable).

- Distortion: ................................... less than 5%.

- Audio broad band: ....................... 300 to 3.000Hz. ±1dB.

- 600Ω line output for data (adjustable)

- Adjacent channel reject: ............... >80dB.

- De-emphasis: ............................... 6dB/eighth - 750μs.

- Input dynamic range: ................... -119dBm. to 0dBm.

- Audio silencer: ............................. Adjustable (7 levels).

- RF level measurer with external output for selection of betterreceived signal.

- F.I. digital filter special for data reception.

- CTS tones detector ...................... Optional.

- Preselector with selective filters to suppress signals out of band.

- FM signal suppression: ............... better 120dB.

- Silencer opening time: .................. 10ms.

- Intermodulation ........................... 70dB

POWER SUPPLY :

- Power: ......................................... 110/220VAC.

- Other supplies: ............................ Optional.

- Power supply: ............................. 150W.

ENVIRONMENTAL SPECIFICATIONS:

- Operation temperature: ............... -20ºC. to +60ºC.

- Relative humidity: ....................... 95%

MECHANICAL SPECIFICATIONS:

- Width: .......................................... Rack19"

- Height: ......................................... 3U (133.5mm.)

- Depth: ......................................... 340mm.

- Weight: ........................................ 4Kg.

Specifications can be changed with no previous notification

11


Spanish Production


MARINE BAND VHFTRANSCEIVER EQUIPMENTFOR COASTAL STATIONS.

RS-232 CONTROL BUS.

- FREQUENCY RANGE: 154,4 A 163,75MHZ. - OPERATION MODES: SIMPLEX, SEMIDUPLEX AND DUPLEX. - G3EJN MODULATIONS. - CHANNELING: 25KHZ. (OTHER CHANNELING OPTIONAL) - ALL INTERNATIONAL MARITIME CHANNELS INCLUDED. - USA CHANNELS OPTIONAL. - OPERATION: LOCAL AND REMOTE. - RS-232-C REMOTE CONTROL BUS. - 110/220VAC. POWER SUPPLY. - OTHER POWER SUPPLIES OPTIONAL. - OUTPUT NOMINAL POWER: 100W. - BUILT-UP IN MODULAR WAY EASY TO MAINTAIN. - POSSIBILITY OF REMOTELY CONTROL ALL ITS PATAMETERS. - COMPLETE PROTRECTION AGAINST OPEN ANTENNA OR IN SHORTCIRCUIT.

100W - VHF TRANSCEIVERMODEL TR-660-A

INVELCO S.A.

Page 1-12

GENERAL SPECIFICATIONS :

- Frequency range: ......................... 154.4 to 163.75 MHz.

- All international maritime channels included.

- Channeling: ................................. 25KHz. (other optional)

- Type of Modulation: .................. G3EJN.

- Modes: ........................................ Simplex, Semiduplex & Duplex

- Frequency stability: .................... 1ppm.

- Remote control: ........................... RS-232-C Bus.

- Completely digital design except for part of the power.

- Channels used in U.S.A.: ............. Optional.

TRANSMITTER :

- Output power: ............................ 100W. ±1dB.

- Reduced power: ........................... W/2; W/4; 1W.

- Output impedance: ...................... 50 ohms.

- Better harmonics supression: ...... 70dB.

- Frequency deviation: ................... ±5KHz.

- Spurios radiation: ........................ better -80dB.

- Audio response: .......................... 300 to 3.000 Hz.

- Pre-emphasis: .............................. 6dB/eighth - 750μs.

- Distortion: ................................... less than 5%

- Independent audio input: ............ Microphone.

Line 600Ω.

Data (line 600Ω).

- Audio compressor: ...................... Included.

- Modulation input level: ............... -30dBm. -0dBm.

- Smaller distortion: ....................... 5%

- Better S/N relation: ...................... 50dB

TECHNICAL CHARACTERISTICS OF THE 100W VHF TRANSCEIVER

MODEL TR-660-A

RECEIVER :

- Input Impedance: ........................ 50 ohms.

- Sensitivity: .................................. -0.25μV for 12dB SINAD.

- Speaker audio output power: ...... 5W.

- Line output: ................................. 600Ω. -40dBm. to 0dBm.(adjustable).

- Distortion: ................................... less than 5%.

- Audio broad band: ....................... 300 to 3.000Hz. ±1dB.

- 600Ω line output for data (adjustable)

- Adjacent channel reject: ............... >80dB.

- De-emphasis: ............................... 6dB/eighth - 750μs.

- Input dynamic range: ................... -119dBm. to 0dBm.

- Audio silencer: ............................. Adjustable (7 levels).

- RF level measurer with external output for selection of betterreceived signal.

- F.I. digital filter special for data reception.

- CTS tones detector ...................... Optional.

- Preselector with selective filters to suppress signals out of band.

- FM signal suppression: ............... better 120dB.

- Silencer opening time: .................. 10ms.

- Intermodulation ........................... 70dB

POWER SUPPLY :

- Power: ......................................... 110/220VAC.

- Other supplies: ............................ Optional.

- Power supply: ............................. 300W.

ENVIRONMENTAL SPECIFICATIONS:

- Operation temperature: ............... -20ºC. to +60ºC.

- Relative humidity: ....................... 95%

MECHANICAL SPECIFICATIONS:

- Width: .......................................... Rack19"

- Height: ......................................... 3U (133.5mm.)

- Depth: ......................................... 340mm.

- Weight: ........................................ 4Kg.

Specifications can be changed with no previous notification

Annotations:

INVELCO S.A.

INVESTIGACIONES ELECTRONICAS YCOMUNICACIONES (INVELCO, S.A.)Ronda de Poniente nº1528760 Tres Cantos, Madrid, (ESPAÑA)Phone. 34-91-803.24.44Fax. 34-91-803.32.28Web: www.invelco.come-mail: [email protected]

catalogo mfhf en - INVELCO · The MD-200-E módem is the lastest development ... The operation...

Documents

Transcript of catalogo mfhf en - INVELCO · The MD-200-E módem is the lastest development ... The operation...