CATALOGO 2012 cliente - s-t-group.com · MOLETEADO EN PIEZA SEGÚN DIN 82 KNURLING ON COMPONENTS...
-
Upload
trinhtuyen -
Category
Documents
-
view
218 -
download
0
Transcript of CATALOGO 2012 cliente - s-t-group.com · MOLETEADO EN PIEZA SEGÚN DIN 82 KNURLING ON COMPONENTS...
INDICE - INDEX
• Moletas según DIN403• Knurls according to DIN403
• Moleteado en pieza según DIN82• Knurling on components according to DIN82
• Moletas para moleteado por corte• Cut knurls
• Moletas para moleteado por deformación• Form knurls
• Moletas especiales (Conicas, concavas y convexas)• Special knurls (Conical, concave and convex)
• Moleteadores por deformación• Pressure knurling tools
• Moleteadores por corte• Cut-knurling tools
• Moleteado por deformación (Datos técnicos)• Pressure knurling (Technical data)
• Velocidades de corte y avances para moleteados por deformación• Table of feeds and speeds for pressure knurling
• Moleteado por corte (Datos técnicos)• Cut-knurling (Technical data)
• Velocidades de corte y avances para moleteados por corte• Table of feeds and speeds for cut-knurling
• Ejemplos de utilización• Knurling applications
2
3
4
5
6
8
26
38
40
41
42
43
MOLETAS SEGÚN DIN 403KNURLS ACCORDING TO DIN403
2
Moleta con dentado rectoStraight pattern Knurl
Moleta con dentado helicoidal derechoRighthand spiral Knurl
Moleta con dentado cruzado puntas entrantesCross-knurl, points down (female)
KVMoleta con dentado cuadrado puntas entrantesSquare knurl, point down (female)
Moleta con dentado cuadrado puntas salientesSquare knurl, points up (male)
Moleta con dentado cruzado puntas salientesCross-knurl, points up (male)
Moleta con dentado helicoidal izquierdoLefthand spiral Knurl
AA BL
BR GE
KEGV
KV KV
Detalle TDetail T
Sección A-ASection A-A
Detalle UDetail U
Sección B-BSection B-B
Detalle WDetail W
Detalle VDetail V
Sección C-CSection C-C
Sección D-DSection D-D
Sección E-ESection E-E
Detalle XDetail X
Sección F-FSection F-F
Detalle YDetail Y
Sección J-JSection J-J
Sección G-GSection G-G
Sección H-HSection H-H
Detalle ZDetail Z
Sección R-RSection R-R
Sección L-LSection L-L
MOLETEADO EN PIEZA SEGÚN DIN 82KNURLING ON COMPONENTS ACCORDING TO DIN82
3
RKVMoleteado cuadrado, puntas entrantesSquare knurling, points down (female)
RGVMoleteado cruzado, puntas entrantesCross-knurling, points down (female)
RKEMoleteado cuadrado, puntas salientesSquare knurling, points up (male)
RBRMoleteado helicoidal derechoRight-hand knurling
Moleteado cruzado puntas salientesCross-knurling, points up (male)
Moleteado helicoidal izquierdoLeft-hand knurling
Moleteado con estrías paralelas al ejeKnurling with grooves parallel to axis
RAA RBL
BRRBR RGE
GV RGV KE RKE
KV RKV
PiezaWorkpiece
DetalleDetail Sección
Section
Moleteado RAAKnurling RAA
PiezaWorkpiece
Moleta AAKnurl AA
PiezaWorkpiece
PiezaWorkpiece
Moleta BLgirada a 30ºKnurl BLswivelled 30º
Moleta BRgirada a 30ºKnurl BRswivelled 30º
Moleteado RAAKnurling RAA
Moleteado RAAKnurling RAA
SecciónSectionDetalle
Detail
PiezaWorkpiece
Moleteado RBLKnurling RBL
PiezaWorkpiece
PiezaWorkpiece
Moleta AAgirada a 30ºKnurl AAswivelled 30º
Moleta BRKnurl BR
DetalleDetail
PiezaWorkpiece
SecciónSection
Moleta AAgirada a 30ºKnurl AAswivelled 30º
Moleta BLKnurl BL
Moleteado RBRKnurling RBR
PiezaWorkpiece
PiezaWorkpiece
PiezaWorkpiece
SecciónSection
DetalleDetail
SecciónSection
Moleteado RGEKnurling RGE
PiezaWorkpiece
Moleta GVKnurl GV
Moleta AAgirada a 30ºKnurl AAswivelled 30º
PiezaWorkpiece
PiezaWorkpiece
PiezaWorkpiece
SecciónSection
DetalleDetail
Moleteado RGVKnurling RGV
Moleta GEKnurl GE
PiezaWorkpiece
SecciónSection
DetalleDetail
SecciónSection
PiezaWorkpiece
Moleteado RKEKnurling RKE
Moleta KVKnurl KV
SecciónSection Sección
Section
PiezaWorkpiece
DetalleDetail
SecciónSection
SecciónSection
Moleteado RKVKnurling RKV
Moleta KEKnurl KE
PiezaWorkpiece
Moleteado RGEKnurling RGE
4
MOLETAS PARA MOLETEADOS POR CORTECUT KNURLS
· Moletas según DIN 403 para moleteados según DIN82· HRc 61±1 estándar· Material estándar: HSS sin recubrimiento· Suministradas indistintamente biseladas o sin biselar· Gran variedad de pasos en stock· Otros pasos disponibles bajo pedido· Caras laterales y agujero rectificados· Amplia gama de materiales y recubrimientos disponibles
· Knurling wheels according to DIN 403 for knurlings as DIN82· HRc 61±1 standard· Standard material: HSS without coating· Delivered chamfered or unchamfered as requested· Wide range of different pitches available in stock· Any other pitch available upon request· Ground faces and central bore· Wide range of materials and coatings available
DimensionesDimensions
8.9x2.5x4
10x3x6
14.5x3x5
15x4x8
21.5x5x8
25x6x8
32x8x14
32x13x16
42x13x16
42x12x18
Pasos Standar / Standard Pitches
✔
0.3
-
-
-
-
-
-
-
-
0.4
✔
✔
✔
✔
-
-
-
-
0.5
✔
✔
✔
✔
-
-
-
-
0.6
✔
✔
✔
✔
-
-
-
-
0.7
✔
✔
✔
✔
-
-
-
-
0.8
✔
✔
✔
✔
-
-
-
-
1.0
✔
✔
✔
✔
✔
✔
1.2
-
-
✔
✔
✔
-
-
-
-
1.4
-
-
-
-
✔
✔
-
-
-
-
1.5
-
-
-
-
✔
✔
✔
✔
1.6
-
-
-
-
✔
✔
-
-
-
-
1.8
-
-
-
-
✔
✔
-
-
-
-
2.0
-
-
-
-
✔
✔
✔
-
-
2.5
-
-
-
-
-
-
-
-
-
-
3.0
-
-
-
-
-
-
✔
✔
3.5
-
-
-
-
-
-
✔
-
-
4.0
-
-
-
-
-
-
✔
-
-
Leyenda / Reference: ✔ Stock permanente / Permanent Stock: = Entrega en plazo reducido / Short term delivery: - = no estándar / not standard
Recubrimientos / Coatings:· Sin recubrimiento (-) Without coating (-)· Nitruro de titanio, TiN (T) Titanium nitride, TiN (T)· Carbonitruro de titanio, TiCN (C) Titanium carbonitride, TiCN (C)· Nitrurado (N) Nitrided (N)· Nitruro de titanio y aluminio, TiAlN (A) Titanium nitride and aluminium, TiAlN (A)· Otros... / Other...
Materiales / Materials :· HSS (-)· HSS + Co (HC)· PM (PM)· PM + Co (PC)· Otros... / Other...
Biselados posibles / Available chamfers:· Sin bisel (S) No chamfer (S)· Biselado una cara (E) One side chamfered (E)· Biselado ambas caras (F) Both sides chamfered (F)
Ejemplo de forma de pedido para una moleta de tamaño 25x8x6, con forma BL30°, de paso 0.8 y ángulo de vano estándar, sin bisel y fabricada en PM y recubierta con carbonitrurode titanio: / Ordering example for a 25x8x6 size knurl, BL30° teeth pattern, a pitch of 0.8mm and standard angle between teeth, without chamfer, manufactured in PM and coated withTitanium Carbonitride:
Recubrimiento / Coating
Material / Material
Bisel / Chamfer
Paso y ángulo del vano (90º estándar) / Pitch and angle between teeth (90° Standard)
Dimensiones / Dimensions
Forma / Teeth pattern
BL30° 25x8x6 0.8 S PM TiCN
Dientes tallados mediante fresado finoFine-milled teeth
AA BL15º BR15º BL30º BR30º
MOLETAS PARA MOLETEADOS POR DEFORMACIÓNFORM-KNURLING KNURLS
5
· Knurling wheels according to DIN 403 for knurlings as DIN 82· HRc 61±1 standard· Standard material: HSS without coating· Delivered chamfered or unchamfered as requested· Wide range of different pitches available in stock· Any other pitch available upon request· Ground faces and central bore· Wide range of materials and coatings available
· Moletas según DIN 403 para moleteados según DIN82· HRc 61±1 estándar· Material estándar: HSS sin recubrimiento· Suministradas indistintamente biseladas o sin biselar· Gran variedad de pasos en stock· Otros pasos disponibles bajo pedido· Caras laterales y agujero rectificados· Amplia gama de materiales y recubrimientos disponibles
Dientes tallados mediante fresado finoFine-milled teeth
AA BL45º BR30ºBL30º BR45º GE30º GE45º KE GV30º GV45º KV
Huella efectuada por deformaciónPattern performed by indentation
DimensionesDimensions
10x4x4
10x5x4
15x4x4
15x5x4
15x6x4
15x5x5
15x6x5
15x6x6/11
20x8x6
20x6x6
20x8x6/13
Pasos Standar / Standard Pitches
✔
0.3
-
-
0.4
✔
✔
✔
0.5
✔
✔
✔
0.6
✔
✔
✔
0.7
✔
✔
✔
0.8
✔
✔
✔
1.0
✔
✔
✔
1.2
✔
✔
1.5
-
-
-
-
1.6
-
-
-
-
-
1.8
-
-
-
-
-
2.0
-
-
-
-
Leyenda / Reference: ✔ Stock permanente / Permanent Stock: = Entrega en plazo reducido / Short term delivery: - = no estándar / not standard
Recubrimientos / Coatings:· Sin recubrimiento (-) Without coating (-)· Nitruro de titanio, TiN (T) Titanium nitride, TiN (T)· Carbonitruro de titanio, TiCN (C) Titanium carbonitride, TiCN (C)· Nitrurado (N) Nitrided (N)· Nitruro de titanio y aluminio, TiAlN (A) Titanium nitride and aluminium, TiAlN (A)· Otros... / Other...
Materiales / Materials :· HSS (-)· HSS + Co (HC)· PM (PM)· PM + Co (PC)· Otros... / Other...
Biselados posibles / Available chamfers:· Sin bisel (S) No chamfer (S)· Biselado una cara (E) One side chamfered (E)· Biselado ambas caras (F) Both sides chamfered (F)
Ejemplo de forma de pedido para una moleta de tamaño 25x8x6, con forma BL30°, de paso 0.8 y ángulo de vano estándar, sin bisel y fabricada en PM y recubierta con carbonitrurode titanio: / Ordering example for a 25x8x6 size knurl, BL30° teeth pattern, a pitch of 0.8mm and standard angle between teeth, without chamfer, manufactured in PM and coated withTitanium Carbonitride:
Recubrimiento / Coating
Material / Material
Bisel / Chamfer
Paso y ángulo del vano (90º estándar) / Pitch and angle between teeth (90° Standard)
Dimensiones / Dimensions
Forma / Teeth pattern
BL30° 25x8x6 0.8 S PM TiCN
DimensionesDimensions
20x10x6
20x8x6.5
25x10x6.5
25x6x6
25x8x6
25x8x8
25x10x6
25x10x8
25x12x8
25x10x15/11
Pasos Standar / Standard Pitches0.3
-
-
-
-
-
-
-
-
0.4
✔
0.5
✔
0.6
✔
0.7
✔
0.8
✔
1.0
✔
1.2
✔
1.5
✔
1.6
✔
1.8
✔
2.0
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔
✔ ✔ ✔ ✔ ✔ ✔ ✔✔
✔
✔
✔ - - - -
- - - -
- -
- -- -
✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔
-
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
-
-
4 4 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
6
MOLETAS ESPECIALESSPECIAL KNURLS
· Moletas cónicas, cóncavas o convexas fabricadas según especificaciones del cliente.· HRc 61±1 estándar· Amplia gama de materiales y recubrimientos disponibles· Caras laterales y agujero rectificados· Dientes tallados por fresado fino
· Conical, convex and concave knurls manufactured to client's specification· HRc 61±1 standard· Wide range of materials and coatings· Ground faces and bore· Fine milled teeth
Necessary data to manufacture conical knurls:· Teeth pattern (KAA, KBL, ...)· Teeth angle· D diameter· D1 bore diameter· E width· Pitch measured at Dm
· Dm mid-diameter or angle of the cone· Material· Coating· Chamfer
Datos necesarios para la fabricación de moletas cónicas:· Forma de tallado (KAA, KBL, ...)· Ángulo del diente· Diámetro D· Diámetro del agujero D1
· Espesor E· Paso en Dm
· Diámetro medio Dm o ángulo del cono· Material· Tratamiento superficial· Biselados
Necessary data to manufacture concave and convex knurls:· Knurl form· Teeth pattern· Teeth angle· D diameter· D1 bore diameter· E width· Pitch· Radius· Material· Coating· Chamfer
Datos necesarios para la fabricación de moletas cóncavas y convexas:· Forma de la moleta· Forma de tallado· Ángulo del diente· Diámetro D· Diámetro del agujero D1
· Espesor E· Paso en D· Radio· Material· Tratamiento superficial· Biselados
Moletas cóncavas y convexasConcave and convex knurls
C DR EDL FL FR
Moletas cónicasConical knurls
KAA KBL KBR KGE
Moleteadorespor deformación
Pressureknurling tools
RAA RBL 30º RBL 45º RBR 30º RBR 45º RGV 30º RGV 45º RGE 30º RGE 45º
AA
BR30º
BL 30ºBR
45ºBL 45º
GE 30º
GE 45º
GV
30ºG
V 45º
8
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M1M1 MODEL
Características· Herramienta de moletear por deformación para trabajos no repetitivos y de precisión media· Indicada tanto para moleteados axiales (F) como radiales (R)· Moleteados axiales (F) solo para las formas RAA, RBL, RBR· Ejes de HSS fijados mediante circlips· Recomendado para moleteados rectos tipo AATipos de máquinas· Para tornos convencionales
Features· Form-knurling tool to perform medium accuracy knurling operations· Not intended for intensive use· Suitable for both traverse (F) and radial (R) feed· Traverse feed (F) only with RAA, RBL, RBR teeth patterns· HSS axles fixed with circlips· Recommended for AA straight knurlingsMachine Types· For conventional lathes
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01010100 M1 20.08.14 R+L O8 200 20x8x6 0.2 EM1
RAA RBL30º RBL45º RBR30º RBR45º RGE30º RGE45º RGV45º RKVRKERGV30ºTipoPattern
MoletaKnurlAvanceFeed
AA BR30º BR45º BL30º BL45º GV30º GV45º GE45º KEKVGE30º
Tipos de moleteados según DIN 82 / Knurlings according to DIN 82
F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ F R✔ F R✔ F R✔ F R✔ F R✔
9
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M7M7 MODEL
Características· Herramienta de moletear por deformación para trabajos no repetitivos y de precisión media· Cabeza portamoletas basculante para un mejor centrado de las moletas sobre la pieza· Indicada tanto para moleteados axiales (F) como radiales (R)· Ejes de HSS fijados mediante circlipsTipos de máquinas· Para tornos convencionales
Features· Form-knurling tool to perform medium accuracy knurling operations· Not intended for intensive use· Tilting head for a better knurl centering on the workpiece· Suitable for both traverse (F) and radial (R) feed· HSS axles fixed with circlipsMachine types· For conventional lathes
Form-kurling basic kit that consists of:1xM1 20.08.141xM7 20.08.252xEM7, spare axle for M7 tool1xEM1, spare axle for M1 toolOne pair of knurls (BR30° + BL30°) and a 0.8 pitchOne pair of knurls (BR30° + BL30°) and a 1.2 pitchOne pair of knurls (BR30° + BL30°) and a 1.6 pitch1 0.8 pitch AA knurl, another of 1.2 pitch and another of 1.6 pitch
KIT M1-M7:
Nota: Las moletas suministradas en este kit son de medida 20x8x6Notice: Knurls delivered within this kit are 20x8x6 sized
Conjunto básico de moleteado por deformación que contiene:1xM1 20.08.141xM7 20.08.252xEM7, eje de repuesto para moleteador M71xEM1, eje de repuesto para moleteador M1Un juego de moletas (BR30° + BL30°) de paso 0.8Un juego de moletas (BR30° + BL30°) de paso 1.2Un juego de moletas (BR30° + BL30°) de paso 1.61 moleta AA de paso 0.8, otra de paso 1.2 y otra de paso 1.6
CódigoCode
ReferenciaReference
kgkg
01110100 KM1-M7 1.1
01160100 M7 20.08.25 R+L O8 200 20X8X6 0.7 EM7
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
10
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M2M2 MODEL
Características· Herramienta de moletear por deformación con cabezal revólver con capacidad para tres pares de moletas· La capacidad de rotación del cabezal asegura el autocentrado de las moletas sobre la pieza· Indicada tanto para moleteados axiales (F) como radiales (R)· Recomendada para moleteado cruzado tipo RGETipos de máquinas· Para tornos convencionales
Features· Form-knurling tool with revolving head able to hold three knurling-wheel pairs· The ability to rotate that the head has ensures the centering of the knurls on the workpiece· Suitable for both traverse (F) and radial (R) feeds· Recommended for RGE crossed knurlingsMachine Types· For conventional lathes
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01020100 M2 20.08.25 R+L O8 200 20X8X6 1.0 EM2
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
11
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M3M3 MODEL
Características· Herramienta de moletear por deformación· Ajuste simétrico de la posición de las moletas al diámetro de la pieza mediante un husillo roscado· Fácil ajuste mediante la tuerca de regulación· No ejerce presión en los rodamientos del torno ya que el esfuerzo es absorbido por la herramienta· Elimina el riesgo de flexión en la pieza, al compensarse entre sí la presión de cada moleta· Indicada tanto para moleteados longitudinales (F), como para radiales (R )· Ejes de HSS bloqueados mediante circlipsTipos de máquinas· Para tornos convencionales
Features· Form-knurling tool· Knurls symmetrically adjustable to the workpiece's diameter through a threaded spindle· Easy adjustment due to the regulation nut· It does not transmit stress to the lathe's bearings as it is wholly stood by the tool· It eliminates bending risk on the workpiece as the pressure of the knurls compensate one with each other· Sutitable for both traverse (F) and radial (R ) feed· HSS axles fixed with circlipsMachine Types· For conventional lathes
01030100 M3 20.08.25 R+L O4 50 20x8x6 1.2 EM3
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
12
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M6M6 MODEL
Características· Herramienta de moletear por deformación· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Moleteados axiales (F) solo para las formas RAA, RBL, RBR· Eje de metal duro· Eje fijado mediante prisionero, lo que permite un cambio rápido de la moletaTipos de máquinas· Tornos automáticos, multihusillo, de cabezal móvil, convencionales y CNC.
Features· Form-knurling tool· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Traverse feed (F) only with RAA, RBL, RBR teeth patterns· Carbide axle· Axle fixed with screws for an instant knurl changeMachine Types· Swiss type , multi-spindle, sliding head, conventional and CNC lathes.
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01062800
01062900
01063000
01063100
01061400
01061500
01061600
01061700
01061900
01062000
01062100
01062200
01062400
01062500
01062600
01062700
M6 15.06.08
M6 15.06.10
M6 15.06.12
M6 15.06.14
M6 20.06.12
M6 20.06.14
M6 20.06.16
M6 20.08.10
M6 20.08.12
M6 20.08.14
M6 20.08.16
M6 20.08.20
M6 20.10.12
M6 20.10.14
M6 20.10.16
M6 20.10.20
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
Ø3÷100
Ø3÷100
Ø3÷100
Ø3÷100
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
A B C D E F
100
100
102,5
102,5
105
105
105
105
105
105
105
105
105
105
105
105
20
20
22,5
22,5
28
28
28
28
28
28
28
28
28
28
28
28
8
10
12
14
12
14
16
20
12
14
16
20
12
14
16
20
8
10
12
14
12
14
16
20
12
14
16
20
12
14
16
20
14
14
14
14
20
20
20
20
20
20
20
20
20
20
20
20
G H kgkg
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2,5
2,5
2,5
2,5
2,5
2,5
2,5
2,5
2,5
14
14
14
14
20
20
20
20
20
20
20
20
20
20
20
20
0.2
0.2
0.2
0.2
0.2
0.2
0.3
0.5
0.5
0.3
0.4
0.5
0.3
0.3
0.4
0.5
*10x4x4*10x5x4*15x4x4*15x5x415x6x4
20X6X6
*20X6X620X8X6
*20X6X6*20X8X620x10x6
1(Ø10)
3,5(Ø15)
3
3
3
EM6 14.4 HM
EM6 20.6 HM
* Con arandelas de suplemento / Using backing washers
RAA RBL30º RBL45º RBR30º RBR45º RGE30º RGE45º RGV45º RKVRKERGV30ºTipoPattern
MoletaKnurlAvanceFeed
AA BR30º BR45º BL30º BL45º GV30º GV45º GE45º KEKVGE30º
Tipos de moleteados según DIN 82 / Knurlings according to DIN 82
F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ F R✔ F R✔ F R✔ F R✔ F R✔
13
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M12 10.04M12 10.04 MODEL
Características· Herramienta de moletear por presión· Ajuste simétrico de la posición de las moletas al diámetro de la pieza mediante un husillo roscado· Fácil ajuste mediante el simple uso de una llave Allen· Sistema modular que permite la utilización de diferentes mangos manteniendo el resto de componentes· No ejerce presión en los rodamientos del torno ya que el esfuerzo es absorbido por la herramienta· Elimina el riesgo de flexión en la pieza, al compensarse entre sí la presión de cada moleta· Dispone de un sistema de auto-centrado para compensar un posible desalineamiento entre la torreta y el eje de la máquina· Indicada tanto para moleteados longitudinales (F), como para radiales (R)· Ejes bloqueados mediante tornillo para un rápido cambio de moletas· Ejes de metal duroTipos de máquinas· Tornos automáticos y multi-husillo
Features· Form-knurling tool· Knurls symmetrically adjustable to the workpiece's diameter through a threaded spindle· Easy adjustment just using an Allen wrench· Modular system that allows the use of several different shanks while keeping the rest of the components· It does not transmit stress to the lathe's bearings as it is wholly stood by the tool· It elliminates bending risk on the workpiece as the pressure of the knurls compensate one with each other· It features an auto-centering system to make up for any possible disalignment between the turret and the machine axis· Suitable for both traverse (F) and radial (R) feed· Carbide axles fixed with circlips for an instant knurl changeMachine Types· For Swiss type and multi-spindle lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01120500
01120600
01120700
01120800
01120900
01121000
M12 10.04.08 R
M12 10.04.08 L
M12 10.04.10 R
M12 10.04.10 L
M12 10.04.12 R
M12 10.04.12 L
R
L
R
L
R
L
Ø1÷10
Ø1÷10
Ø1÷10
Ø1÷10
Ø1÷10
Ø1÷10
D
12
12
12
12
12
12
kgkg0.2
0.2
0.2
0.2
0.2
0.2
EM12
C
8
8
10
10
12
12
10x4x4
10x4x4
10x4x4
10x4x4
10x4x4
10x4x4
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
14
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M8M8 MODEL
Características· Herramienta de moletear por deformación· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Moleteados axiales (F) solo para las formas RAA, RBL, RBR· Eje de metal duro· Eje fijado mediante prisionero, lo que permite un cambio rápido de la moletaTipos de máquinas· Tornos automáticos, multihusillo, de cabezal móvil, convencionales y CNC.
Features· Form-knurling tool· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Traverse feed (F) only with RAA, RBL, RBR teeth patterns· Carbide axles· Axle fixed with a screw for an instant knurl changeTipos de máquinas· Swiss type, multi-spindle, sliding head, conventional and CNC lathes.
RepuestoSpare Part
ReferenciaReference
CódigoCode
Ver.Ver.
Capacidad/Capacity Molet./Knurl
01201300
01200700
01200100
01201400
01200800
01200200
01201500
01200900
01200300
01201600
01200400
01201000
01201700
01201100
01201800
01201200
M8 15.06.08 R
M8 15.05.08 R
M8 15.04.08 R
M8 15.06.08 L
M8 15.05.08 L
M8 15.04.08 L
M8 15.06.10 R
M8 15.05.10 R
M8 15.04.10 R
M8 15.06.10 L
M8 15.05.10 L
M8 15.04.10 L
M8 15.06.12 R
M8 15.05.12 R
M8 15.06.12 L
M8 15.05.12 L
Ø3÷100
Ø3÷100
Ø3÷100
Ø3÷100
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
A B C E F kgkg
Ø3÷100
Ø3÷100
Ø3÷100
Ø3÷100
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø5÷200
Ø15Ø10 Ø15Ø10
R
L
R
L
R
L
Ø3÷50
Ø3÷50
Ø3÷50
Ø3÷50
Ø3÷50
Ø3÷50
Ø3÷100
Ø3÷100
Ø3÷100
Ø3÷100
Ø3÷100
Ø3÷100
10x6x4*
10x5x4**
10x4x4
10x6x4*
10x5x4**
10x4x4
10x6x4*
10x5x4**
10x4x4
10x6x4*
10x5x4**
10x4x4
10x6x4*
10x5x4**
10x6x4*
10x5x4**
15x6x4*
15x5x4**
15xf4x4
15x6x4*
15x5x4**
15x4x4
15x6x4*
15x5x4**
15x4x4
15x6x4*
15x5x4**
15x4x4
15x6x4*
15x5x4**
15x6x4*
15x5x4**
Ø15 Ø15Ø10 Ø15Ø10 Ø15Ø10
96.5
96.5
96.5
96.5
96.5
96.5
99
99
99
99
99
99
16.5
16.5
16.5
16.5
16.5
16.5
19
19
19
19
19
19
8
8
10
10
12
12
15
15
15
15
15
15
17.5
17.5
17.5
17.5
17.5
17.5
2
2
2
2
2
2
4.5
4.5
4.5
4.5
4.5
4.5
0.2
0.2
0.2
0.2
0.2
0.2
EM8 12.4 HM
Ø10
* Se pueden montar moletas de 4 o 5mm de espesor utilizando arandelas de suplemento ** Se pueden montar moletas de 4mm de espesor utilizando una arandela de suplemento* 4 or 5mm thick knurls can be used backing them with washers ** 4mm thick knurls can be used backing them with washers
RAA RBL30º RBL45º RBR30º RBR45º RGE30º RGE45º RGV45º RKVRKERGV30ºTipoPattern
MoletaKnurlAvanceFeed
AA BR30º BR45º BL30º BL45º GV30º GV45º GE45º KEKVGE30º
Tipos de moleteados según DIN 82 / Knurlings according to DIN 82
F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ F R✔ F R✔ F R✔ F R✔ F R✔
15
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M9M9 MODEL
Características· Herramienta de moletear por deformación· Cabeza portamoletas basculante para un mejor centrado de las moletas sobre la pieza· Cabeza portamoletas reversible para trabajar tanto a derechas como a izquierdas.· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Eje de metal duro· Ejes fijados mediante prisionero lo que permite un cambio rápido de la moletaTipos de máquinas· Tornos automáticos, multiusillo, de cabezal móvil, convencionales y CNC
Features· Form-knurling tool· Tilting head for a better centering of the knurls on the workpiece· Ability to work on left-handed and right-handed lathes just turning over the head· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Carbide axles· Axle fixed with a screw for an instant knurl changeMachine Types· Swiss type, multi-spindle, sliding head, conventional and CNC lathes
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01180100
01180200
01180300
01180400
01180500
01180600
M9 10.04.08
M9 10.04.10
M9 10.04.12
M9 15.04.16
M9 15.05.16
M9 15.06.16
R+L
R+L
R+L
R+L
R+L
R+L
Ø3÷50
Ø3÷50
Ø3÷50
Ø3÷100
Ø5÷100
Ø5÷100
A
107
107
107
130.5
130.5
130.5
B
27
27
27
40.5
40.5
40.5
C
8
10
12
16
16
16
E
21
21
21
32
32
32
G
2
2
2
3
3
3
H
12
12
12
16
16
16
kgkg0.1
0.1
0.1
0.2
0.2
0.2
10x4x4
F
2
2
2
1.5
1.5
1.5
EM9 12.4 HM
EM9 16.4 HM15x5x4
15x4x4
15x6x4
16
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M4M4 MODEL
Características· Herramienta de moletear por deformación· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Moleteados axiales (F) solo para las formas RAA, RBL, RBR· Eje de metal duro· Eje fijado mediante prisionero lo que permite un cambio rápido de la moletaTipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC.
Features· Form-knurling tool· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Traverse feed (F) only with RAA, RBL, RBR teeth patterns· Carbide axle· Axle fixed with screws for an instant knurl changeMachine Types· Swiss type, multi-spindle conventional and CNC lathes.
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01041300
01041400
01041500
01041600
01041700
01041800
01041900
01042000
01042100
01042200
M4 20.08.20
M4 20.08.25
M4 20.10.20
M4 20.10.25
M4 25.08.20
M4 25.08.25
M4 25.10.20
M4 25.10.25
M4 25.12.20
M4 25.12.25
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
Ø8÷200
Ø8÷200
Ø8÷200
Ø8÷200
Ø8÷300
Ø8÷300
Ø8÷300
Ø8÷300
Ø8÷300
Ø8÷300
A B C E F
119.5
119.5
119.5
119.5
122
122
122
122
122
122
29.5
29.5
29.5
29.5
32
32
32
32
32
32
20
25
20
25
20
25
20
25
20
25
30
35
30
35
32.5
37.5
32.5
37.5
32.5
37.5
2.5
2.5
2.5
2.5
5
5
5
5
5
5
EM4/M5 20.06 HM
kgkg
*25x8x8*25x10x825x12x8
20x8x6
*20x8x620x10x6
25x8x8
*25x8x825x10x8
0.4
0.5
0.4
0.5
0.4
0.5
0.4
0.5
0.4
0.5
EM4/M5 20.08 HM
* Con arandelas de suplemento / * Using backing washers
RAA RBL30º RBL45º RBR30º RBR45º RGE30º RGE45º RGV45º RKVRKERGV30ºTipoPattern
MoletaKnurlAvanceFeed
AA BR30º BR45º BL30º BL45º GV30º GV45º GE45º KEKVGE30º
Tipos de moleteados según DIN 82 / Knurlings according to DIN 82
F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ F R✔ F R✔ F R✔ F R✔ F R✔
17
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M5M5 MODEL
Características· Herramienta de moletear por deformación· Cabeza portamoletas basculante para un mejor centrado de las moletas sobre la pieza· Cabeza portamoletas reversible para trabajar tanto a derechas como a izquierdas· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Ejes de metal duro· Ejes fijados mediante prisionero lo que permite un cambio rápido de la moletaTipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Form-knurling tool· Tilting head for a better centering of the knurls on the workpiece· Ability to work on left-handed and right-handed lathes just turning over the head· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Carbide axles· Axles fixed with a screw for an instant knurl changeMachine Types· Swiss type, multi-spindle, sliding head, conventional and CNC lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01050700
01050800
01050900
01051000
01050100
01050200
01050300
01050400
01050500
01050600
M5 20.08.20
M5 20.08.25
M5 20.10.20
M5 20.10.25
M5 25.08.20
M5 25.08.25
M5 25.10.20
M5 25.10.25
M5 25.12.20
M5 25.12.25
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
R+L
Ø8÷200
Ø8÷200
Ø8÷200
Ø8÷200
Ø8÷300
Ø8÷300
Ø8÷300
Ø8÷300
Ø8÷300
Ø8÷300
A B C E F
139.5
139.5
139.5
139.5
150
150
150
150
150
150
49
49
49
49
60
60
60
60
60
60
20
25
20
25
20
25
20
25
20
25
42
42
42
42
55
55
55
55
55
55
2.5
2.5
2.5
2.5
2.1
2.1
2.1
2.1
2.1
2.1
EM4/M5 20.06 HM
kgkg
*25x8x8*25x10x825x12x8
20x8x6
*20x8x620x10x6
25x8x8
*25x8x825x10x8
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
EM4/M5 20.08 HM
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
* Con arandelas de suplemento / * Using backing washers
18
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M10M10 MODEL
Características· Herramienta de moletear por deformación· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Moleteados axiales (F) solo para las formas RAA, RBL, RBR· Ejes fijados mediante prisionero lo que permite un cambio rápido de la moleta· Para moleteados hasta una cara lateralTipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC.
Features· Form-knurling tool· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Traverse feed (F) only with RAA, RBL, RBR pattens· Axles fixed with a screw for an instant knurl change· For knurlings up to a vertical faceMachine Types· Swiss type, multi-spindle, conventional and CNC lathes.
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01070100
01070200
M10 25.10.20
M10 25.10.25
R+L
R+L
E
30
35
kgkg0.7
0.8EAM10 25
C
20
2525x10x15/11Ø8÷200
RAA RBL30º RBL45º RBR30º RBR45º RGE30º RGE45º RGV45º RKVRKERGV30ºTipoPattern
MoletaKnurlAvanceFeed
AA BR30º BR45º BL30º BL45º GV30º GV45º GE45º KEKVGE30º
Tipos de moleteados según DIN 82 / Knurlings according to DIN 82
F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ F R✔ F R✔ F R✔ F R✔ F R✔
19
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M11M11 MODEL
Características· Herramienta de moletear por deformación· Cabeza portamoletas basculante para un mejor centrado de las moletas sobre la pieza· Dada la posición de las moletas, la herramienta puede realizar moleteados hasta una cara lateral.· Posibilidad de corrección del ángulo de ataque de la moleta mediante dos espárragos Allen situados en el mango· Indicada tanto para moleteados axiales (F) como radiales (R)· Ejes fijados mediante prisionero lo que permite un cambio rápido de la moleta· Para moleteados hasta una cara lateralTipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Form-knurling tool· Tilting head for a better centering of the knurls on the workpiece· Possibility to vary clearance angle by means of a pair of screws placed in the shank· Suitable for both traverse (F) and radial (R) feed· Axles fixed with screws for an instant knurl change· For knurlings up to a vertical faceMachine Types· Swiss type, multi-spindle, conventional and CNC lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01080100
01080200
01080300
01080400
M11 25.10.20R
M11 25.10.20L
M11 25.10.25R
M11 25.10.25L
R+L
R+L
R+L
R+L
Ø8÷200
Ø8÷200
Ø8÷200
Ø8÷200
C
20
20
25
25
25x10x15/11 ETM11 25
kgkg1.0
1.0
1.2
1.2
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
20
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
Características· Cabezal de moletear por presión de tres garras para moleteados sobre pequeños diámetros· Tres garras portamoletas dispuestas a 120° accionadas simultáneamente mediante un anillo sincronizador· La unión entre el vástago de anclaje a máquina y el cuerpo principal de la herramienta dispone de un sistema de autoajuste que permite corregir posibles desalineamientos entre la torreta y el cabezal de la máquina· Herramienta para moleteado frontal (F)· Ejes de metal duro· Ejes asegurados mediante un prisionero para facilitar los cambios de moletasTipos de máquinas· Tornos convencionales, CNC, multihusillo, de cabezal móvil y automáticos
Features· Three wheeled form-knurling tool to perform knurlings on small diameter workpieces· Three knurl bearing jaws placed at 120° moved by a synchronizing ring· The coupling between the shank and the head has an auto adjusting system that allows to make up for any possible disalignment between the turret and the chuck of the machine· Suitable only for frontal (F) knurlings· Carbide axles· Axles fixed wity circlips for instant knurl changeTipos de máquinas· Conventional, CNC, multi-spindle, sliding head and Swiss type lathes
LONGITUD MÁXIMA DE MOLETEADO (mm)MAXIMUM KNURLING LENGTH (mm)
ModeloModel
Ø PiezaPiece Ø
Mango StandardStandard Shaft
Mango Especial TaladroSpecial Bored Shaft
M17 10.04M17 20.06M17 20.06M17 20.06
2÷104÷144÷214÷30
40693717
105135
--
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01170100
01170300
01170200
01170400
01170600
01170500
M17 10.04.210
M17 10.04.210 1/2''
M17 20.06.430
M17 20.06.430 1”
M17 20.06.430 22
M17 20.06.430
A B C D F
16
12.7
20
25.4
22
19.05
EM17 10.04
kgkg1.07
1.01
1.39
1.45
1.43
1.41
EM17 20.06R+L
R+L
R+LØ2÷10
Ø4÷30
0.5
1.7
10x4x4
20x6x6
107
139
57.5
57.5
44
70R+L
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA+AA
RGE30º
BL30º+BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
MODELO M17M17 MODEL
F R✔
BL45º+BL45º+BR45º
F R✔ F R✔
21
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M12 25.10M12 25.10 MODEL
Características· Herramienta de moletear por presión· Ajuste simétrico de la posición de las moletas al diámetro de la pieza mediante un husillo roscado· Fácil ajuste mediante el simple uso de una llave Allen· Sistema modular que permite la utilización de diferentes mangos manteniendo el resto de componentes· No ejerce presión en los rodamientos del torno ya que el esfuerzo es absorbido por la herramienta· Posibilidad de montaje tanto a derechas como a izquierdas· Elimina el riesgo de flexión en la pieza, al compensarse entre sí la presión de cada moleta· Dispone de un sistema de auto-centrado para compensar un posible desalineamiento entre la torreta y el eje de la máquina· Indicada tanto para moleteados longitudinales (F), como para radiales (R )· Ejes de metal duro· Ejes bloqueados mediante tornillo para un rápido cambio de moletasTipos de máquinas· Tornos convencionales, CNC y multi-husillo
Features· Form-knurling tool· Knurls symmetrically adjustable to the workpiece's diameter through a threaded spindle· Easy adjustment just using an Allen wrench· Modular system that allows the use of several different shanks keeping the rest of the components· It does not transmit stress to the bearings of the machine as it is stood by the tool· Possibility to mount on right-handed or left-handed lathes· Eliminates bending risk on the workpiece as each knurl's presure compensates one with each other· It has an auto-centering systems that compensates for any possible disalignment between the turret and the machine axis· Suitable for both traverse (F) and radial (R) feed· Carbide axles· Axles fixed with a screw for an instant knurl changeMachine Types· Conventional, CNC and multi-spindle lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01120100
01120300
M12 25.10.20
M12 25.10.20
R+L
R+L
Ø5÷50
Ø5÷50
D
25
25
kgkg2.1
2.1EM12 25.10 HM
C
20
25
25x10x8
25x10x8
TipoPattern
MoletaKnurlAvanceFeed
RAA
AA+AA
RGE30º
BL30º+BR30º
RGE45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
F R✔ ✔
BL45º+BR45º
F R✔ ✔ F R✔ ✔
22
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M19M19 MODEL
Características· Herramienta de moletear por deformación para moleteaados interiores· Indicada tanto para moleteados axiales (F) como radiales (R)· Moleteados axiales (F) solo para las formas RAA, RBL, RBR· Sustitución rápida de la moleta (eje asegurado mediante espárragos roscados)Tipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC.
Features· Form-knurling tool for internal knurlings· Sutiable for both traverse (F) and radial (R) knurlings· Traverse feeding (F) only for RAA, RBL, RBR patterns· Axle fixed with screws for instant knurl changeMachine Types· Swiss type, multi-spindle, conventional and CNC lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01190100
01190200
M19 25.10.20
M19 25.10.25
R+L
R+L
Ø27÷200
Ø27÷200
C
20
2525x10x15/11 EAM10 25
kgkg0.2
0.3
RAA RBL30º RBL45º RBR30º RBR45º RGE30º RGE45º RGV45º RKVRKERGV30ºTipoPattern
MoletaKnurlAvanceFeed
AA BR30º BR45º BL30º BL45º GV30º GV45º GE45º KEKVGE30º
Tipos de moleteados según DIN 82 / Knurlings according to DIN 82
F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ ✔ F R✔ F R✔ F R✔ F R✔ F R✔ F R✔
23
MOLETEADORES POR DEFORMACIÓNFORM-KNURLING TOOLS
MODELO M15M15 MODEL
Características· Herramienta de moletear por deformación para moleteados cónicos o frontales· Cabeza portamoletas giratoria para posicionar la moleta de acuerdo al ángulo del cono de la pieza· Doble sistema de bloqueo de la cabeza porta-moletas que confiere una gran rigidez al conjunto porta-moletas-mango· Posibilidad de montaje tanto a derechas como a izquierdas· Eje de metal duro· Eje fijado mediante un prisionero para un cambio rápido de la moletaTipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Form-knurling tool for conical or frontal knurlings· Swivel head to place the knurl according to the workpiece's cone angle· Double head blocking system that conferes high rigidity to the whole tool assembly· Possibility to work in both right-handed and left-handed lathes· Carbide axle· Axle fixed with a screw for an instant knurl changeMachine Types· Automatic, multi-spindle, conventional and CNC lathes
TipoPattern
MoletaKnurlAvanceFeed
RKAA
KAA
P
RKBL30º
KBR30º
P
RKBR30º
KBL30º
P
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
MoletaKnurl
01150300
01150400
01150500
01150600
M15 25.08.20
M15 25.08.25
M15 25.10.20
M15 15.10.25
R+L
R+L
R+L
R+L
B
46
46
46
46
20
25
20
25
A
160
160
160
160
kgkgC
0.6
0.8
0.6
0.8
CÓNICACONICAL
EM11
24
MOLETEADORES POR DEFORMACIÓN FORM-KNURLING TOOLS
MODELO M16M16 MODEL
Características· Herramienta de moletear por deformación para moleteados cónicos· Especial para norma DIN-72783· Ajuste simétrico de la posición de las moletas al diámetro de la pieza mediante un husillo roscado· Fácil ajuste mediante el simple uso de una llave Allen· Sistema modular que permite la utilización de diferentes mangos manteniendo el resto de componentes· Fabricación del mango según el acoplamiento de la máquina a la que vaya destinada· Posibilidad de montaje tanto a derechas como a izquierdas· No ejerce presión en los rodamientos del torno ya que el esfuerzo es absorbido por la herramienta· Elimina el riesgo de flexión en la pieza, al compensarse la presión de cada moleta· Dispone de un sistema de auto-centrado para compensar un posible desalineamiento entre la torreta y el eje de la máquina· Para moleteado frontal· Ejes de metal duro· Eje bloqueado mediante tornillo para un rápido cambio de moletasTipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Form-knurling tools for conical knurlings· Special for DIN-72783 knurlings· Symmetrical knurl set to the workpiece's diameter using a threaded spindle· Easy adjustment just using an Allen wrench· Modular system that allows the use of several different shanks keeping the same components· Shank manufactured to client's specification· Possibility to work in both right-handed and left-handed lathes· It does not transmit stress to the bearings of the machine as it is stood by the tool· Eliminates bending risk in the workpiece as each knurl's pressure compensates one with each other· It features an auto-centering system to compensate for a possible disalignment between the turret and the machine axis· For frontal knurlings· Carbide axles· Axles fixed with screws for an instant knurl changeMachine Types· Swiss type, multi-spindle, conventional and CNC lathes
TipoPattern
MoletaKnurlAvanceFeed
RKAA
KAA+KAA
RKGE30º RKGE45º
KBL45º+KBR45º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
KBL30º+KBR30º
01210100 M6FRONTALFRONTAL
CÓNICACONICAL
1.5 EM16Ø1÷12
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
F R✔ F R✔ F R✔
Moleteadorespor corte
Cut-knurlingtools
26
MOLETEADORES POR CORTE CUT-KNURLING TOOLS
MODELO MFS 89.25MFS 89.25 MODEL
Características· Herramienta de moletear por corte· Fácil ajuste mediante el simple uso de una llave Allen· Cabeza pivotante para un mejor alineamiento de la moleta· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinasTornos de cabezal móvil y automáticos
Features· Cut knurling tool· Easy setting just using an Allen wrench· Pivoting head for a better knurl alignment· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Sutiable only for traverse (F) feedsMachine Types· Sliding-head and Swiss type lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01090900
01091000
01091100
01091200
01091300
01091400
MFS 89.25.08 R
MFS 89.25.08 L
MFS 89.25.10 R
MFS 89.25.10 L
MFS 89.25.12 R
MFS 89.25.12 L
R
L
R
L
R
L
Ø1.5÷12mm
Ø1.5÷12mm
Ø1.5÷12mm
Ø1.5÷12mm
Ø1.5÷12mm
Ø1.5÷12mm
D
8
8
10
10
12
12
kgkg0.2
0.2
0.2
0.2
0.2
0.2
C
8
8
10
10
12
12
ES 89.25 HSS8.9x2.5x4
TipoPattern
MoletaKnurl
AvanceFeed
RAA
BR30º
RBR30º
AA
RBL30º
AA
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RAA
BL30º
F R✔ F R✔ F R✔ F R✔
Con hta.With tool
Versión derecha (R)Right -handed (R)
Versión izquierda (L)Left -handed (L)
27
MOLETEADORES POR CORTECUT-KNURLING TOOLS
MODELO MF 89.25MF 89.25 MODEL
Características· Herramienta de moletear por corte· Ajuste de las moletas según el diámetro de la pieza a moletear mediante escala graduada· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas en función del mango montado· Cabeza pivotante para un mejor alineado de las moletas· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos de cabezal móvil y automáticos
Features· Cut-knurling tool· Easy knurl setting to the diameter of the workpiece thanks to a graduated scale· Easy adjustment just using an Allen wrench· Possibility to work in right-handed or left-handed lathes depending on the mounted shank· Tilting head for a better knurl alignment· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Suitable only for traverse (F) feedMachine Types· Sliding-head and Swiss type lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01101300
01101400
01101500
01101600
01101700
01101800
MF 89.25.08 R
MF 89.25.08 L
MF 89.25.10 R
MF 89.25.10 L
MF 89.25.12 R
MF 89.25.12 L
R
L
R
L
R
L
Ø1.5÷12 mm
Ø1.5÷12 mm
Ø1.5÷12 mm
Ø1.5÷12 mm
Ø1.5÷12 mm
Ø1.5÷12 mm
C
8
8
10
10
12
12
kgkg0.2
0.2
0.2
0.2
0.2
0.2
8.9x2.5x4
8.9x2.5x4
8.9x2.5x4
8.9x2.5x4
8.9x2.5x4
8.9x2.5x4
EAT 89.25
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
28
MOLETEADORES POR CORTE CUT-KNURLING TOOLS
MODELO MFS1 14.53MFS1 14.53 MODEL
Características· Herramienta de moletear por corte· Fácil ajuste mediante el simple uso de una llave Allen· Cabeza pivotante para un mejor alineamiento de la moleta· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos de cabezal móvil y automáticos
Features· Cut knurling tool· Easy setting just using an Allen wrench· Pivoting head for a better knurl alignment· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Sutiable only for traverse (F) feedsMachine Types· Sliding-head and Swiss type lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01260100
01260200
01260300
01260400
01260500
01260600
MFS1 14.53.12R
MFS1 14.53.12L
MFS1 14.53.14R
MFS1 14.53.14L
MFS1 14.53.16R
MFS1 14.53.16L
R
L
R
L
R
L
D kgkgC
Ø3÷50mm 14.5X3X5 EAT 14.53
14 12 0.3
14 14 0.28
16 16 0.26
Ø3÷50mm
Ø3÷50mm
14.5X3X5
14.5X3X5
TipoPattern
MoletaKnurl
AvanceFeed
RAA
BR30º
RBR30º
AA
RBL30º
AA
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RAA
BL30º
F R✔ F R✔ F R✔ F R✔
Con hta.With tool
Versión derecha (R)Right -handed (R)
Versión izquierda (L)Left -handed (L)
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01250100
01250200
01250300
MF1 14.53.12R
MF1 14.53.12L
MF1 14.53.14R
R+L
R+L
R+L
D
8
8
10
10
12
12
kgkg0,2
0,2
0,2
0,2
0,2
0,2
C
EAT 14.53Ø3÷50mm 14.5X3X5
14
14
16
12
14
16
0.45
0.46
0.50
29
MOLETEADORES POR CORTECUT-KNURLING TOOLS
MODELO MF1 14.53MF1 14.53 MODEL
Características· Herramienta de moletear por corte· Ajuste de las moletas según el diámetro de la pieza a moletear mediante escala graduada· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas variando la posición del mago· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos de cabezal móvil y automáticos
Features· Cut-knurling tool· Knurl setting to the diameter of the workpiece thanks to a graduated scale· Easy adjustment just using an Allen wrench· Possibility to work in right-handed or left-handed lathes changing the position of the shank· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Suitable only for traverse (F) feedMachine Types· Sliding-head and Swiss type lathes
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
30
MOLETEADORES POR CORTE CUT-KNURLING TOOLS
MODELO MFS 14.53MFS 14.53 MODEL
Características· Herramienta de moletear por corte· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas simplemente girando la cabeza· Cabeza pivotante para un mejor alineamiento de la moleta· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Cut-knurling tool· Easy setting just using an Allen wrench· Possibility to work in right-handed and left-handed lathes just turning over the head· Tilting head for a better knurl alignment· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Suitable only for traverse (F) feedMachine Types· Swiss type, multi-spindle, conventional and CNC lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01090100
01090200
MFS 14.53.14
MFS 14.53.16
R+L
R+L
D kgkgC
EAT 14.53Ø3÷50mm
Ø3÷50mm
14
16
16
16
0.242
0.26214.5X3X5
TipoPattern
MoletaKnurl
AvanceFeed
RAA
BR30º
RBR30º
AA
RBL30º
AA
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RAA
BL30º
F R✔ F R✔ F R✔ F R✔
Con hta.With tool
Versión derecha (R)Right -handed (R)
Versión izquierda (L)Left -handed (L)
31
MOLETEADORES POR CORTECUT-KNURLING TOOLS
MODELO MF 14.53MF 14.53 MODEL
Características· Herramienta de moletear por corte· Ajuste de las moletas segú'fan el diámetro de la pieza a moletear mediante escala graduada· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas en función del mango montado· Cabeza pivotante para un mejor alineamiento de las moletas· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Cut-knurling tool· Kurl setting to the diameter of the workpiece thanks to a graduated scale· Easy adjustment just using an Allen wrench· Possibility to work in right-handed or left-handed lathes depending on the assembled shank· Tilting head for a better knurl alignment· Modular system that allows the use of different shanks keeping the same head· Possibility to vary the clearance angle· Suitable only for traverse (F) feedMachine Types· Swiss type, multi-spindle, automatic and CNC lathes
Ø3÷50
Ø3÷50
Ø3÷50
Ø3÷50
14.5x3x5
14.5x3x5
14.5x3x5
14.5x3x5
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01100100
01100200
01100300
01100400
MF 14.53.14 R
MF 14.53.14 L
MF 14.53.16 R
MF 14.53.16 L
D kgkgC
EAT 14.53
14
14
16
16
16
16
16
16
0.494
0.494
0.518
0.518
R
L
R
L
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
32
MOLETEADORES POR CORTE CUT-KNURLING TOOLS
MODELO MFS 21.55MFS 21.55 MODEL
Características· Herramienta de moletear por corte· Fácil ajuste mediante el simple uso de una llave Allen· Cabeza pivotante para un mejor alineamiento de la moleta· Posibilidad de trabajar tanto a derechas como a izquierdas simplemente girando la cabeza· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Cut-knurling tool· Easy adjustment just using an Allen wrench· Tilting head for a better knurl alingment· Possibility to work in right-handed and left-handed lathes just turning over the head· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Suitable only for traverse (F) feedMachine Types· Swiss type, multi-spindle, conventional and CNC lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01090300
01090400
MFS 21.55.20
MFS 21.55.25
R+L
R+L
D kgkgC
EAT 21.55Ø4÷250mm
Ø4÷250mm21.5x5x8
20
25
25
25
0,2
0,2
TipoPattern
MoletaKnurl
AvanceFeed
RAA
BR30º
RBR30º
AA
RBL30º
AA
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RAA
BL30º
F R✔ F R✔ F R✔ F R✔
Con hta.With tool
Versión derecha (R)Right -handed (R)
Versión izquierda (L)Left -handed (L)
MOLETEADORES POR CORTECUT-KNURLING TOOLS
MODELO MF 21.55MF 21.55 MODEL
Caracteristicas· Herramienta de moletear por corte· Ajuste de las moletas según el diámetro de la pieza a moletear mediante escala graduada· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas simplemente girando la cabeza· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Posibilidad de corrección del ángulo de ataque· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos automáticos, multihusillo, convencionales y CNC
Features· Cut-knurling tool· Knurl setting to the diameter of the workpiece thanks to a graduated scale· Easy adjustment just using an Allen wrench· Possibility to work in right-handed or left-handed lathes just turning over the head· Modular system that allows the use of several different shanks keeping the same head· Possibility to vary the clearance angle· Suitable only for traverse (F) feedMachine Types· Swiss type, multi-spindle, conventional and CNC lathes
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01100500
01100600
01100700
01100800
MF 21.55.20 R
MF 21.55.20 L
MF 21.55.25 R
MF 21.55.25 L
R+L
R+L
R+L
R+L
D kgkgC
EAT 21.55
20
20
25
25
25
25
25
25
1.254
1.254
1.364
1.364
33
Ø5÷250mm 21.5X5X8
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01140100
01140200
01140300
01140400
MF 21.55 VDI 30R
MF 21.55 VDI 30L
MF 21.55 VDI 40R
MF 21.55 VDI 40L
R
L
R
L
B kgkgA C D E
Ø3÷50mm 21.5x5x8 EAT 21.55
126
126
136
136
55
55
63
63
30
30
40
40
68
68
78
78
95
95
98
98
2.6
2.6
2.9
2.9
34
MOLETEADORES POR CORTE CUT-KNURLING TOOLS
MODELO MF 21.55 VDIMF 21.55 VDI MODEL
Características· Herramienta de moletear por corte· Ajuste de las moletas según el diámetro de la pieza a moletear · mediante escala graduada· Fácil ajuste mediante el simple uso de una llave Allen· Cabeza pivotante para un mejor alineamiento de las moletas· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Tornos CNC con torreta según DIN 69880
Features· Cut-knurling tool· Knurl setting to the diameter of the workpiece thanks to a graduated scale· Easy adjustment just using an Allen wrench· Tilting head for a better knurl alingment· Suitable only for traverse (F) feedMachine Types· CNC lathes with DIN 69880 type turrets
KIT MF 21.55 - MFS 21.55Kit básico de moleteado por corteque incluye:
· 1 MF 21.55 con moletas AA de paso 1· 1 MFS 21.55 con moleta BR30°· Llaves Allen de servicio
KIT MF 21.55 - MFS 21.55Basic cut-knurling kit comprised of:
· 1 MF 21.55 with 2 AA , 1mm pitch knurls· 1 MFS 21.55 with1BR30° knurl· Allen wrenches
CodigoCode
01220200
01220300
MangoShank
20x25
20x25
ReferenciaReference
KMF 20
KMF 25
KgKg3
3.3
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
35
MOLETEADORES POR CORTECUT-KNURLING TOOLS
MODELO MF 12MF 12 MODEL
Características· Herramienta de acción compensada para moleteado por corte. Recomendada para moleteados de perfil RGE 30° y RGE 45°· Ajuste simétrico de la posición de las moletas al diámetro de la pieza mediante un husillo roscado· Fácil ajuste mediante el simple uso de una llave Allen· Sistema modular que permite la utilización de diferentes mangos manteniendo el resto de componentes· No ejerce presión en los rodamientos del torno ya que el esfuerzo es absorbido por la herramienta· Elimina el riesgo de flexión en la pieza, al compensarse la presión de cada moleta· Dispone de un sistema de auto-centrado para compensar un posible desalineamiento entre la torreta y el eje de la máquina· Únicamente admite moleteados longitudinales (F)· Eje bloqueado mediante tornillo para un rápido cambio de moletasTipos de máquinas· Tornos automáticos y multi-husillo
Features· Balanced action cut-knurling tool. Recommended for RGE 30° and RGE 45° pattern knurlings· Knurls symmetrically adjustable to the workpiece's diameter through a threaded spindle· Easy adjustment just using an Allen wrench· Modular system that allows the use of several different shanks keeping the rest of the componenes· It does not transmit any stress to the bearings of the lathe as it is stood by the tool· Elliminates bending risk in the workpiece as each knurl's pressure compensates one with each other· It features an auto-centering system that makes up for any possible disalignment between the turret and the machine axis.· Suitable only for traverse (F) feed· Axles fixed with screws for an instant knurl chanteMachine Type· Recommended for Swiss type and multi-spindle lathes
MMF12 89.25.08R
MMF12 89.25.08L
MMF12 89.25.10R
MMF12 89.25.10L
MMF12 89.25.12R
MMF12 89.25.12L
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
01130100
01130200
01130300
01130400
01130500
01130600
R
L
R
L
R
L
D kgkgC
8
8
10
10
12
12
12
12
12
12
12
12
0.2
0.2
0.2
0.2
0.2
0.2
EMF 12Ø1÷10mm 2.9X2.5
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
36
MOLETEADORES POR CORTE CUT-KNURLING TOOLS
MODELO MFS 42.12MFS 42.12 MODEL
Características· Herramienta de moletear por corte· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas simplemente girando la cabeza· Cabeza pivotante para un mejor alineamiento de la moleta· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Para grandes tornos
Features· Cut knurling tool· Easy setting just using an Allen wrench· Pivoting head for a better knurl alignment· Modular system that allows the use of several different shanks keeping the same head· Sutiable only for traverse (F) feedsMachine Types· For big sized lathes
01270100 MFS 42.12.40 R+L O30 3000 42x12x18 7.0 C 42.12
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
TipoPattern
MoletaKnurl
AvanceFeed
RAA
BR30º
RBR30º
AA
RBL30º
AA
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RAA
BL30º
F R✔ F R✔ F R✔ F R✔
Con hta.With tool
Versión derecha (R)Right -handed (R)
Versión izquierda (L)Left -handed (L)
37
MOLETEADORES POR CORTECUT-KNURLING TOOLS
MODELO MF 42MF 42 MODEL
Caracteristicas· Herramienta de moletear por corte· Ajuste de las moletas según el diámetro de la pieza a moletear mediante escala graduada· Fácil ajuste mediante el simple uso de una llave Allen· Posibilidad de trabajar tanto a derechas como a izquierdas simplemente girando la cabeza· Sistema modular que permite la utilización de diferentes mangos con la misma cabeza portamoletas· Indicada sólo para moleteados longitudinales (F)Tipos de máquinas· Para grandes tornos
Features· Cut-knurling tool· Knurl setting to the diameter of the workpiece thanks to a graduated scale· Easy adjustment just using an Allen wrench· Possibility to work in right-handed or left-handed lathes just turning over the head· Modular system that allows the use of several different shanks keeping the same head· Suitable only for traverse (F) feedMachine Types· For big sized lathes
01240100 MF 42.12.40 R+L O30 3000 42x12x18 9.0 EAT 42.12
kgkg
RepuestoSpare Part
ReferenciaReference
CódigoCode
VersiónVersion
CapacidadCapacity
MoletaKnurl
TipoPattern
MoletaKnurlAvanceFeed
RGE45º
BL15º+BR15º
RGE60º
BL30º+BR30º
Tipos de moleteados según DIN 82Knurlings according to DIN 82
RGE30º
AA+AA
F R✔ F R✔ F R✔
38
MOLETEADO POR DEFORMACIÓNPRESSURE KNURLING
Se produce por el conformado en frío del material mientraslas moletas presionan la pieza. Dicha deformación produceun incremento del diámetro de partida de la pieza, segúnlos valores aproximados indicados en la siguiente tabla:
Los valores arriba mostrados sirven solo como guía, pudiéndose obtener mejores resultados mediante pruebas a pie de máquina.These values are intended as a guide, and better results may be obtained by tests carried out on machines
Incremento del diámetro de la pieza moleteada (Valores en mm)Increase in knurled part diameter (mm)
Tipo 0.3 0. 4 0.5 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0.08
0.08
0.08
0.10
RAA
RBL
RBR
RGE
0.13
0.13
0.13
0.18
0.18
0.21
0.21
0.17
0.22
0.24
0.24
0.30
0.36
0.33
0.33
0.38
0.43
0.43
0.43
0.51
0.50
0.52
0.52
0.63
0.58
0.65
0.65
0.70
0.66
0.70
0.70
0.83
0.68
0.76
0.76
0.93
0.96
0.87
0.87
0.95
RAA
RBL
RBR
RGE
0.08
0.10
0.10
0.12
0.15
0.15
0.15
0.20
0.20
0.23
0.23
0.29
0.24
0.26
0.26
0.32
0.38
0.35
0.35
0.40
0.45
0.45
0.45
0.53
0.52
0.54
0.54
0.65
0.60
0.67
0.67
0.73
0.68
0.72
0.72
0.85
0.70
0.78
0.78
0.95
0.98
0.90
0.90
0.98
RAA
RBL
RBR
RGE
0.10
0.12
0.12
0.10
0.14
0.20
0.20
0.14
0.20
0.23
0.23
0.20
0.25
0.29
0.29
0.25
0.33
0.40
0.40
0.33
0.45
0.50
0.50
0.53
0.50
0.60
0.60
0.52
0.60
0.70
0.70
0.65
0.70
0.78
0.78
0.70
0.80
0.88
0.88
0.75
0.90
0.98
0.98
0.80
RAA
RBL
RBR
RGE
0.10
0.12
0.12
0.11
0.15
0.17
0.17
0.15
0.20
0.24
0.24
0.22
0.25
0.27
0.27
0.25
0.33
0.39
0.39
0.33
0.45
0.49
0.49
0.45
0.50
0.57
0.57
0.53
0.58
0.58
0.58
0.65
0.65
0.65
0.65
0.70
0.79
0.80
0.80
0.74
0.85
0.95
0.95
0.90
RAA
RBL
RBR
RGE
0.10
0.10
0.10
0.12
0.15
0.15
0.15
0.17
0.20
0.20
0.20
0.20
0.25
0.23
0.23
0.23
0.30
0.30
0.30
0.30
0.35
0.40
0.40
0.38
0.42
0.45
0.45
0.40
0.45
0.53
0.53
0.46
0.50
0.59
0.59
0.50
0.52
0.63
0.63
0.60
0.56
0.68
0.68
0.65
Paso (mm)Pitch (mm)
Acero de 90 Kg.90 Kgt. steel
Acero de 60 Kg.60 Kgt. steel.
Acero inoxidableStainless steel
AluminioAluminium
LatónBrass
MaterialMaterial
This is done by cold forming the material while the knurls exertspressure on the workpiece. This causes an increase in thestarting diameter of the part in accordance with the approximatevalues indicated in the following table:
39
MOLETEADO POR DEFORMACIÓN (DATOS TÉCNICOS)PRESSURE KNURLING (TECHNICAL DATA)
El moleteado por deformación se puede ejecutar de dos maneras:
· Moleteado radial, cuando la longitud moleteada en la pieza coincide con el espesor de la moleta a utilizar.
· Moleteado axial, cuando la longitud excede al espesor de la moleta. Para este segundo caso la moleta siempre hade estar biselada en sus extremos.
La norma DIN 82 (véase pag. 3) regula los diferentes tipos demoleteados que se pueden mecanizar en las piezas. La mayoríade ellos pueden ser realizados indistintamente de ambos modosutilizando una, dos o tres moletas, exceptuando los RGV y RKVque recomendamos realizarlos trabajando radialmente.
Cuando se trabaja con una herramienta de deformación sepueden conseguir diferentes tipos de moleteados en función delnúmero y de la forma de las moletas montadas.
Pressure knurling can be done in two ways:
• Radial method when the length of knurl on the component coincides with the width of the knurl wheel being used.
• Axial method when the length of knurl required exceeds the width of the knurl wheel being used. In this case, the knurl (s) travel along the component and therefore must be bevelled.
The DIN 82 standard (see page 3) specifies the different kindsof knurling patterns that can be machined on components.Most of these can be done in either of the two ways, using one,two or three knurls, except for the RGV and RKV knurlingpattern, which we recommend should be done by the radialmethod.When working with a pressure knurling tool, different kinds ofknurling patterns can be obtained, depending on the type ofknurls and tools being used.
BL 30º + BR30º RGE30º
BL 30º + BR30º + BR30º RGE30º
Moleteador de presiónde una moleta
Pressure knurling withone wheel knurlingtool
AA RAA
BL45º RBR45º
BR30º RBL30º
BR45º RBL45º
GE30º RGV30º
GE45º RGV45º
GV30º RGE30º
GV45º RGE45º
KE RKV
KV RKE
BL30º RBR30º
Moleteador de presiónde dos moletas
Pressure knurlingwith two wheels Knurlingtool
AA + AA RAA
BL45º + BR45º RGE45º
Moleteador de presiónde tres moletas
Pressure knurlingwith three wheels Knurlingtool
AA + AA + AA RAA
BL45º + BR45º + BR45º RGE45'
Herramienta Moleta MoletadoTool Knurl Knurling
✔ ✔
Avance radial Avance axialRadial feeding Traverse feeding
✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔
40
VELOCIDADES DE CORTE Y AVANCES PARA MOLETEADOS POR DEFORMACIÓNTABLE OF FEEDS AND SPEEDS FOR PRESSURE KNURLING
<10
10 - 50
50 - 100
100 - 250
>250
10
15
20
25
<10
10 - 50
50 - 100
100 - 250
>250
Avance radial(mm/rev):
0.3 ÷ 0.6
Avance axial (mm/rev)para pasos:
0.20
0.26
0.30
0.30
0.40
0.40
0.6 ÷ 1.2 1.2 ÷ 1.6 1.6 ÷ 2.0
Vc(m/min)
10
15
20
25
<10
10 - 50
50 - 100
100 - 250
>250
10
15
20
25
<10
10 - 50
50 - 100
100 - 250
>250
10
15
20
25
<10
10 - 50
50 - 100
100 - 250
>250
10
15
20
25
<10
10 - 50
50 - 100
100 - 250
>250
10
15
20
25
<10
10 - 50
50 - 100
100 - 250
>250
10
15
20
25
25 ÷ 55
30 ÷ 60
20 ÷ 50
20 ÷ 55
20 ÷ 40
20 ÷ 45
20 ÷ 40
20 ÷ 45
25 ÷ 60
35 ÷ 70
35 ÷ 75
45 ÷ 90
25 ÷ 55
30 ÷ 60
0.04 ÷ 0.08
0.04 ÷ 0.08
0.04 ÷ 0.08
0.04 ÷ 0.08
0.04 ÷ 0.08
0.04 ÷ 0.08
0.04 ÷ 0.08
0.12
0.16
0.18
0.18
0.26
0.26
0.08
0.12
0.15
0.15
0.16
0.16
0.06
0.08
0.10
0.10
0.12
0.12
0.18
0.24
0.28
0.28
0.36
0.36
0.10
0.14
0.16
0.16
0.24
0.24
0.06
0.10
0.12
0.12
0.14
0.14
0.04
0.06
0.08
0.08
0.10
0.100.14
0.20
0.25
0.25
0.30
0.30
0.08
0.12
0.15
0.15
0.20
0.20
0.06
0.10
0.12
0.12
0.14
0.14
0.04
0.06
0.08
0.08
0.10
0.10
0.14
0.20
0.25
0.25
0.30
0.30
0.08
0.12
0.15
0.15
0.20
0.20
0.06
0.10
0.12
0.12
0.14
0.14
0.04
0.06
0.08
0.08
0.10
0.10
0.12
0.16
0.20
0.20
0.26
0.26
0.08
0.10
0.15
0.15
0.18
0.18
0.05
0.08
0.10
0.10
0.12
0.12
0.04
0.06
0.06
0.06
0.08
0.08
0.25
0.30
0.40
0.40
0.50
0.50
0.15
0.20
0.25
0.25
0.30
0.30
0.10
0.15
0.20
0.20
0.20
0.20
0.08
0.10
0.15
0.15
0.15
0.15
0.20
0.26
0.30
0.30
0.40
0.40
0.12
0.16
0.18
0.18
0.26
0.26
0.08
0.12
0.15
0.15
0.16
0.16
0.06
0.08
0.10
0.10
0.12
0.12
Los valores arriba mostrados sirven solo como guía, pudiéndose obtener mejores resultados mediante pruebas a pie de máquina.These values are intended as a guide, and better results may be obtained by tests carried out on machines
Acero de 60 Kg.60 Kgt. steel
Acero de 90 Kg.90 Kgt. steel
Acero inoxidableStainless steel
Acero fundidoCast Iron
AluminioAluminium
LatónBrass
BronceBronze
f radial(mm/rev):
MaterialMaterial f axial (mm/rev) Pitch:
Ø pieza(mm)
workpiece Ø(mm)
Ø moleta(mm)
knurl Ø(mm)
41
MOLETEADO POR CORTE (DATOS TÉCNICOS)CUT-KNURLING (TECHNICAL DATA)
Se produce por corte del material. En este caso las moletastrabajan como una fresa y el recrecimiento del material respectodel diámetro de origen es muy pequeño. Asimismo el esfuerzosoportado por la pieza, cabezal y contrapunto de la máquinaes mínimo. Las moletas han de tener la arista viva yno se puede trabajar radialmente, salvo en el iniciodel moleteado en el extremo del mismo.
In this case the knurls actually cut the material, working like amilling tool with a very small increase in the diameter of thematerial. Likewise, the stress withstood by the part, head andtailstock of the machine is minimal. The knurl wheels musthave sharp edges and cannot be plunged radiallyexcept when starting to knurl at the corner edgeof the component.
The DIN 82 standard (see page 3) specifies the different kindsof knurling patterns than can be machined on components.Using the cut-knurling system the RGV and RKV type knurlingpatterns cannot be made.When working with a cut-knurling tool, different kinds of knurlingpatterns can be obtained, depending on the type of knurls andtools being used.
La norma DIN 82 (véase pag. 3) regula los diferentes tipos demoleteados que se pueden mecanizar en las piezas. Utilizandoel sistema de moleteado por corte, los moleteados tipo RGVy RKV no pueden ser realizados.Cuando se trabaja con una herramienta de corte se puedenconseguir diferentes tipos de moleteados en función del númeroy la forma de las moletas montadas y de la versión de laherramienta utilizada.
Los valores arriba mostrados sirven solo como guía, pudiéndose obtener mejores resultados mediante pruebas a pie de máquina.These values are intended as a guide, and better results may be obtained by tests carried out on machines
Avance axialTraverse feeding
Derecha (R)Right (R)
Moleteador de cortede una moleta
Cut-Knurling withone wheelcut-knurling tool:
Izquierda (L)Left (L)
AA
BR30º
AA
BL30º
RBR30º
RAA
RBL30º
RAA
Moleteador de cortede dos moletas
cut-Knurling withone wheelcut-knurling tool:
AA+AA
BL15º+BR15º
BL30º+BR30º
RGE30º
RGE45º
RGE60º
AA+AA
BL15º+BR15º
BL30º+BR30º
RGE30º
RGE45º
RGE60º
Derecha (R)Right (R)
Izquierda (L)Left (L)
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Herramienta Modelo Moleta MoletadoTool version Knurl Knurling
42
VELOCIDADES DE CORTE Y AVANCES PARA MOLETEADOS POR CORTETABLE OF FEEDS AND SPEEDS FOR CUT KNURLING
Acero de 60 Kg.60 Kgt. steel
Acero de 90 Kg.90 Kgt. steel
Acero inoxidableStainless steel
Acero fundidoCast Iron
AluminioAluminium
LatónBrass
BronceBronze
Avance radial(mm/rev):
0.3 ÷ 0.6
Avance axial (mm/rev)para pasos:
0.14
0.15
0.20
0.22
0.25
0.30
0.32
0.6 ÷ 1.2 1.2 ÷ 1.6 1.6 ÷ 2.0
Vc(m/min)
0.04 ÷ 0.10
0.04 ÷ 0.10
0.04 ÷ 0.10
0.04 ÷ 0.10
0.04 ÷ 0.10
0.04 ÷ 0.10
0.04 ÷ 0.10
0.09
0.10
0.13
0.15
0.18
0.20
0.21
0.06
0.08
0.10
0.12
0.12
0.13
0.14
0.05
0.06
0.07
0.08
0.08
0.09
0.10
0.12
0.13
0.18
0.20
0.23
0.28
0.30
0.07
0.08
0.11
0.13
0.16
0.18
0.20
0.05
0.07
0.08
0.10
0.10
0.12
0.12
0.05
0.05
0.05
0.06
0.06
0.07
0.080.12
0.13
0.17
0.19
0.21
0.26
0.27
0.08
0.09
0.11
0.13
0.15
0.17
0.18
0.05
0.07
0.09
0.10
0.10
0.11
0.12
0.04
0.05
0.06
0.07
0.07
0.08
0.09
Los valores arriba mostrados sirven solo como guía, pudiéndose obtener mejores resultados mediante pruebas a pie de máquina.These values are intended as a guide, and better results may be obtained by tests carried out on machines
42
35
45
40
60
55
50
95
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
42
25
35
30
45
40
35
60
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
42
22
30
28
35
32
30
50
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
42
22
30
28
35
32
30
50
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
42
70
80
70
110
100
95
150
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
42
60
70
60
100
90
85
140
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
42
35
45
40
60
55
50
95
<12
12-50
50-100
100-250
>250
8.9
14.5
21.5
0.12
0.13
0.17
0.19
0.21
0.26
0.27
0.08
0.09
0.11
0.13
0.15
0.17
0.18
0.05
0.07
0.09
0.10
0.10
0.11
0.12
0.04
0.05
0.06
0.07
0.07
0.08
0.090.18
0.20
0.25
0.27
0.31
0.38
0.40
0.11
0.13
0.16
0.18
0.23
0.25
0.26
0.08
0.10
0.13
0.14
0.15
0.16
0.18
0.06
0.07
0.09
0.09
0.10
0.11
0.13
0.15
0.17
0.21
0.22
0.26
0.32
0.34
0.09
0.10
0.14
0.16
0.19
0.21
0.22
0.06
0.07
0.11
0.12
0.13
0.14
0.15
0.05
0.06
0.07
0.07
0.08
0.09
0.11
0.13
0.15
0.19
0.20
0.24
0.30
0.32
0.07
0.08
0.12
0.14
0.17
0.20
0.20
0.05
0.06
0.10
0.10
0.11
0.12
0.13
0.05
0.05
0.06
0.06
0.07
0.08
0.10
f radial(mm/rev):
MaterialMaterial
f axial (mm/rev) Pitch:
Ø pieza(mm)
workpiece Ø(mm)
Ø moleta(mm)
knurl Ø(mm)
44
EJEMPLOS DE UTILIZACIÓNKNURLING APPLICATIONS
El moleteado pordeformación esinsustituible entre otros enlos ejemplos que siguen:
Para recrecer el diámetrode origen. (Fig. 1)
Para moletear en el fondode gargantas. (Fig. 2)
Para moletear en toda sulongitud diámetroslimitados por caras.(Fig. 3)
Para moletear sobre zonascónicas. (Fig. 4)
Para moletear axialmente.(Fig. 5)
Although pressure knurlingcan be used for manygeneral applications, whereit “forms up” increasingdias.
Knurling at the bottom ofgrooves
Knurling up to a shoulder.
Knurling conical areas
Knurling "bands" of knurlmidway along acomponent diameter.
Por deformación Pressure knurling
El moleteado por cortehace que el recrecimientodel diámetro de la piezamecanizada sea muyinferior al que se produceutilizando el metodo dedeformación. (Fig. 6)
Posibilita moletear piezastubulares cuya ejecuciónsería irrealizable pordeformación.(Fig. 7 y 8)
Es indispensable paramoletear piezas demateriales plásticos yhierro fundido ya que elmoleteado pordeformación sobre dichosmateriales no consiguehacer fluir el materialnecesario para conformarlas crestas.
Dado que las moletas vandispuestas angularmenteen el soporte, esto provocaque al moletear undiámetro limitado por unacara quede un espacioentre esta y el final delmoleteado. (Fig. 9)
Cut-knurling means theincrease of the machinedpart diameter would beconsiderably less thanwhen using pressureknurling;
Allows tubular parts to beknurled which wouldotherwise be impossible bypressure.
It is essential for knurlingplastic materials and castiron, because pressureimpedes the necessarymaterial flow to shaperidges;
Due to the angulararrangement of the knurlsin the holder, it is notpossible to knurl right upto a shoulder.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 1
Cut-knurlingPor Corte