Catalog Tevi Fitinguri Pvcu Plasson
-
Upload
zenogredina -
Category
Documents
-
view
132 -
download
8
Transcript of Catalog Tevi Fitinguri Pvcu Plasson
PVC Fittings & ValvesPVC Fittings & ValvesTechnical Catalogue
Edi t ion
20
0
6
Pipes for pressure conduits. PVC 125
Laying instruction
The joint connections can be supplied both in execu tion with thermoformed socket by
gluing.
The ring jointing (sliding connection) is generally adopted to compensate automaticallythe foreseen dilatations on the conduit, cause of t emperature changes, and is
characterized by the use of an elastomeric gasket, of such a section that permits a
guaranteed capacity by two subsequent dams, (so of a non toroidal section) with
differentiated pressures exerted on the generatrix of the introduced trunk of pipe. Therecent forming technicals of the receiving socket, consent to realize very narrow
tolerances and give rise to ideal conditions for un iform stresses on the circumference of
the pipe.Such solutions have allowed to realize jointings wit h an unexceptionable functional
behaviour with a perfect sealing on the most diffic ult conditions of work. On an erecting
yard, the right execution of a ring system jointing foreees the following operations:- scrupulous cleaning of the part that will receive the gasket;
- application of a slippage lubricant to facilitate the introduction of the gasket;
- introduction of the gasket in the current positio n;
- introduction of the end part of the pipe after a n accurate cleaning.The gluing jointing (rigid connection) is particularly suitable for th e mechanized
execution of the underground fixed installations. T he security of the jointing is
guaranteed in this case from characteristics of the mixture used as glue to give a realchemical sealing between the contacting surfaces. F or the execution of a good gluing it is
necessary to follow the work stages as:
-inspections of the chamfering on the pipe and to i nsert on the socket;-cleaning with thin emery-paper drenched with deter gent (methylene chloride) on the
surfaces to glue;
-smearing of the end part of the pipe and the insid e of the socket, with glue for Rigid PVC
(Tangit type);-immediate introduction of the pipe inside the sock et, without rotating movement, kee
ping everything still, for a few seconds;
-timely cleaning (at once) of the exceeding glue wi th the emery-paper.After the drying process time of 24 hours the connec tion can be submitted to a testing-
maximum pressure of 15 Kg/cm2, for a maximum pressure work of 10 Kg/cm2, 8 hours
time of drying process are enough.
*Pvc 100= Pipes suitable to support in work a unita ry load of security = 100 Kg/cm2 at 20°C.
R e l i a b l e l i n k s bu i l d a d u r a b l e p i p i n g n e t wo r kR e l y o n P l a s s o n ' s f i t t i n g s fo r l o n g t e r m s y s t e m p e r fo r m a n c e
Plasson's innovative products revolutionized the way of connectingpolyethylene pipes in the 1960's. We started with fittings for agriculturalirrigation and later developed products for urban water distribution.
High pressure PVC Fittings and Valves are part of Plasson's wide rangeof products. Plasson has achieved superior designs and products anda genuine commitment to quality, delivery and service.
Plasson continues to strive for the future environment. By buying Plassonproducts you help us invest in our vision of a world where clean, purewater will be everyone's birthright.
Introduction
Contents
CEMENTED FITTINGS
ADAPTOR FITTINGS
THREADED FITTINGS
FITTINGS ACCESSORIES
VALVES
CHECK VALVES
AIR RELEASE VALVES
VALVES ACCESSORIES
TECHNICAL SPECIFICATIONS - FITTINGS
TECHNICAL SPECIFICATIONS - VALVES
ASSEMBLY INSTRUCTIONS
1 - 5
6 - 9
1 0 - 1 3
1 4 - 1 5
1 6 - 1 8
1 9 - 2 0
2 1
2 2 - 2 3
2 4 - 2 5
2 6 - 2 7
2 8 - 3 1
45o Elbow-Cemented
5090
5360
5450
5510
5520
5900
5910
5920
5012
5022
5032
5042
5500
Short Reducing BushingCemented
Hose Adaptor-Cemented
Flange Adaptorwith O-Ring-Cemented
Stub Flat Faceto fit 5500-Cemented
Stub Serrated-Cemented
Loose Flange
Blind Flange
Fixed Flange
Socket Adaptor-Cemented-Threaded
Reducer AdaptorMale-FemaleCemented-Threaded
Adaptor SocketMale-FemaleCemented-Threaded
90o TeeCemented-Threaded
Page4
Page4
Page4
Page5
Page5
Page5
Page6
Page3
Page6
Page6
Page3
Page6
Page4
5010Socket-Cemented
Page1
5020Reducing SocketMale-Female-Cemented
Page1
5040 Page290o Tee-Cemented
505090o Elbow-Cemented
Page2
5070End Cap-Cemented
Page2
5080Union-Cemented
Page2
514090o Reducing Tee-Cemented
Page3
574290
o Tee
Cemented-Threadedwith Reinforcing Ring
Page9
505290o ElbowCemented-Threaded
Page7
5362Hose Adaptor withThreaded Nut
Page8
5062AdaptorMale-FemaleCemented-Male-Threaded
Page7
5082Union AdaptorFemaleCemented-Threaded
Page7
5212AdaptorMale-FemaleCemented-Male-Threaded
Page7
5222Bushing AdaptorMale-FemaleCemented-Male-Threaded
Page8
545245o ElbowCemented-Threaded
Page8
5712Socket AdaptorCemented-Threadedwith Reinforcing Ring
Page8
5722 Page8Reducer Adaptor
Male Cemented-FemaleThreaded with Reinforcing Ring
90o Tee-Threaded
5041 Page10
5161Reducing Nipple-Threaded
Page11
5081Union Female-Threaded
Page11
5071Cap-Threaded
Page11
5061Nipple-Threaded
Page11
505190 Elbow-Threaded
Page10
ReducerMale-Female-Threaded
5021 Page10
5011Socket-Threaded
Page10
5752 Page990
o Elbow
Cemented-Threaded withReinforcing Ring
5171Plug-Threaded
Page12
5581Bushing for Unions: 5081,5082
Page14
5580Bushing for Union 5080
Page14
5480Nut for Unions: 5080, 5081,5082, 5083, 5084, 5362
Page14
5083Union Male-Female-Cemented-Threaded
Page13
5583 Page14Male Threaded Union
Bush for Items: 5083, 5084
5361Hose Adaptor-Threaded
Page12
5221Nipple SocketMale-Female-Threaded
Page12
545145o Elbow-Threaded
Page12
5921Fixed Flange-Threaded
Page13
5084Union Male-FemaleThreaded
Page13
5680End for Unions: 5080,5082, 5083
Page14
5681End for Unions: 5081, 5084
Page15
5609O - Ring for Item 5500
Page15
5629Washer for 5520 and 5362
Page15
5639O - Ring for Unions: 5080,5081, 5082, 5083, 5084
Page15
1150Two Nut Valve-Cemented
Page16
1140Two Nut Valve-Cemented
Page16
1151Two Nut Valve-Threaded
Page16
1141Two Nut Valve-Threaded
Page16
1250/1280Bistop Valve-Cemented
Page16
1240/1270Bistop Valve-Cemented
Page16
1251/1281Bistop Valve-Threaded
Page17
5048 Page19Knocker Tee-Cemented
1241/1271Bistop Valve-Threaded
Page17
1341One Nut Valve-Threaded
Page17
1641/1601Foot Valve-Threaded
Page20
1640/1600Foot Valve-Cemented
Page20
1061/1001/1081/1091Check Valve-Threaded
Page19
1110Valve Collar-Cemented
Page22
1111Valve Collar-Threaded
Page22
1114Valve Nut
Page22
1112/1113Blue/Red Handles
Page22
1631/1691Air Release Valve-Threaded
Page21
Page21
1630/1690Air Release Valve-Cemented
1340One Nut Valve-Cemented
Page17
1350One Nut Valve-Cemented
Page17
1060/1000/1080/1090Check Valve-Cemented
Page19
1351One Nut Valve-Threaded
Page17
1379One Nut Valve-Female-Threaded Compression
Page18
1361One Nut Valve-ThreadedMale-Female
Page18
1451Agrifit One Nut ValveThreaded Female-Female
Page18
1461Agrifit One Nut ValveThreaded Male-Female
Page18
CEMENTED FITTINGS
1
5010 Socket - Cemented
Z PFA (PN) Wd E H lUKCUKCUKCUKCUKCUKCUKCUKCUKCUCUUUUU
162025324050637590110125140160200225
2328344251587388105126143161181228250
3035424856668093108128145160181224257
14161922263138445161697686106119
23444445667891219
161616161616161616161616161010
915243861641192103455257901100140030004600
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
H
z l
Ed
H PFA(PN) WL l I1 E
5020 Reducing SocketMale-Female - Cemented
Dxdxd120x16x1625x20x1625x20x2032x25x1632x25x2032x25x2540x32x1640x32x2040x32x2540x32x3250x40x2050x40x2550x40x3250x40x4063x50x2563x50x3263x50x4063x50x5075x63x3275x63x4075x63x5075x63x6390x75x4090x75x5090x75x6390x75x75110x90x50110x90x63110x90x75110x90x90125x110x63125x110x75125x110x90125x110x110140x125x110160x140x110160x140x125225x200x160
16191922222226262626313131313838383844444444515151516161616169696969768686119
14161619191922222222262626263131313138383838444444445151515161616161697676106
1414161416191416192216192226192226312226313826313844313844513844516161616986
20222522273122263239273340493240496140496174496273896176901067890105123130130145185
36394241435050525457616265697276798586879210099103111117117125133138121125126127149157160230
1616161616161616161616161616161616161616161616161616161616161616161616161610
61010151820232630355050556588931001251201301501632252322252904104414905454604604654406458258902100
D d
I
L
l1
H
Ed1
CEMENTED FITTINGS
2
5040 90º Tee - Cemented
Z PFA (PN) Wd E H lUKCUKCUKCUKCUKCUKCUKCUKCUKCUCUUU
162025324050637590110125140160200225
2328344248627790108132148162184232258
4655657898118145170199239269298339420465
14161922263138445161697686106119
9121417232835414959667384102114
161616161616161616161616101010
18294472122160386590970166021702650355072009700
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
E
d
H
zl
5070 End Cap - Cemented
PFA (PN) Wd E H IUKCUKCUKCUKCUKCUKCUKCUKCUKCUCUUU
162025324050637590110125140160
2328344251627788105126143161181
2024283242475763738598108123
14161922263138445161697686
16161616161616161616161616
611182851801411792704166409051160
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
H
dE
I
5080 Union - Cemented
PFA(PN) Wd E H I=I1
UUUUUUU
162025324050637590110
34425259727996118132151
39455157677995110125145
14161922263138445161
16161616161616101010
91524386194167210345525
11131313151719222323
Z
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
I1
H
I
dE d
5050 90º Elbow - Cemented
Z PFA (PN) Wd E H IUKCUKCUKCUKCUKCUKCUKCUKCUKCUCUUU
162025324050637590110125140160200225
2328344248597490108132148162184232258
354250607590111130154186209230262326363
14161922263138445161697686106119
9121417232835414959667384102114
161616161616161616161616161010
1321325368120220450730123216201970285058507500
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
z I
d E
H
3
CEMENTED FITTINGS
5360 Hose Adaptor - Cemented
WED LH1216202532405063
1216202530405060
485864758895102118
1014161922263138
4814263361120163
D
H
E
5140 90º Reducing Tee - Cemented
PFA(PN) WE E1 Idxd1
25x2032x2032x2540x2040x2540x3250x2550x3250x4063x3263x4063x50
192222262626313131383838
273333273341334150415061
131821222222232323343434
161616161616161616161616
366963110110115180190180335340350
334141505050616161777777
141717242424282828343434
161619161922192226222631
667878999999118118118144144144
4564576366697780849599104
I1 Z Z1 H H1
E1d1
I1Z
1
d
IZH
H1
E
5090 Short Reducing Bushing -Cemented
PFA (PN) WL I ZDxd20x1625x1625x2032x1632x2032x2540x2040x2540x3250x2550x3250x4063x3263x4063x5075x4075x5075x6390x5090x6390x75110x63110x75110x90125x75125x90125x110140x90140x110140x125160x110160x125160x140200x160200x180225x160225x200
161919222222262626313131383838444444515151616161696969767676868686106106119119
141416141619161922192226222631263138313844384451445161516169616976869686106
25386310741295161271813620137231710251882515725171020103313
16161616161616161616161616161616161616161616161616161616161616161610101010
3851515102527174350327683601219580195183137340315260450430265590447326775725560140099024501670
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
D d
IZ
L
CEMENTED FITTINGS
4
5450 45º Elbow - Cemented
PFA (PN) WE lZdUKCUKCUKCUKCUKCUKCUKCUKCUKCUCUUU
2328344252617791109132148163184232258
14161922263138445161697686106119
55681012151721252831354550
161616161616161616161616161010
132029489212223336659099013201620218050006200
162025324050637590110125140160200225
Quality certifications : U = UNI-IIP, K = Kiwa, C = NF-CSTB.
E
d
ZI
5510 Stub Flat Face to fit 5500 -Cemented
PFA(PN) WE I Zd E1 B H
2025324050637590110125140160200225
344150617390106125150169188213254272
7778891011121112131718
33333345556678
1616161616161616161616161010
1016254060100150240370585735100016551805
27334150617688105126146163185228249
161922263138445161697686106119
192225293441485666748292113126
ZI
H
dE E1
B
5520 Stub Serrated - Cemented
PFA(PN) WE I Zd E1 B H
2025324050637590110125140160200225
344150617390106125150169188213254272
7778891011121112131718
33333345556678
1616161616161616161616161010
1016254060100150240370585735100016601810
27334150617688105126146163185228249
161922263138445161697686106119
192225293441485666748292113126
E d E1
H
I z
B5500 Flange Adaptor with O-Ring -
Cemented
B PFA(PN) WE I Zd
2025324050637590110125140160200225
344150617390106125150169188213254272
1010101313141516181718192325
666888810111112121314
1616161616161616161616161010
1218275570120175270420670860114013001500
27334150617688105126146163185228249
161922263138445161697686106119
222528343946536172808898119133
E1 H
B
E1
ZI
H
dE
5
CEMENTED FITTINGS
5900 Loose Flange
PFA(PN) WE SDpd
324050637590110125140160200225
115140150165185200220230250289340340
141818181818181818222222
85100110125145160180191211241297297
161616161616161616161010
130205235300390465540585750105018502100
4454658094112135151168193238255
141516181920222528303232
444448888888
E1 H N
E E1
S
H
Dp
5910 Blind Flange
PFA(PN) WE SDpd H N
324050637590110125140160200225
141818181818181818222222
85100110125145160180191211241297297
161616161616161616161010
1432402863904906407868481125174327002950
115140150165185200220230250289340340
141516181920222528303232
444448888888
S
Dp E
H
5920 Fixed Flange
PFA(PN) WE SDpd ZH NI
324050637590110
115140150165185200220
22263138445161
23273239475464
85100110125145160180
14181818181818
4444488
16161616161616
140240290400540710940
3333456
E
ZI
dDp
S
H
6
ADAPTOR FITTINGS
5022 Reducer AdaptorMale-Female - Cemented-Threaded
PFA(PN) WC HLtB L
25x1/2”32x3/4”40x1”
50x11/4”63x11/2”
75x2”90x21/2”110x3”
1718202222262933
1922263138445161
1616161616161616
193062100135180268468
30365065658095120
1212161616202020
46506368758394106
DxG
H
B
G C
LtL
D
5012 Socket AdaptorCemented-Threaded
PFA(PN) WB LtDxG HI ZC
12121212161616202428
3333444555
13171820222226293340
16161616161616161616
1018274264103167190333483
2530404555658090108130
14161922263138445161
303640455257687889106
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”75x21/2”
90x3”110x4”
B
d
I Z
H
Lt
G C
5032 Adaptor SocketMale-Female - Cemented-Threaded
PFA(PN) WC HLtB L
25x3/4”32x1”
40x11/4”50x11/2”
63x2”75x21/2”
90x3”110x4”
1820222226293340
1922263138445161
1616161616161616
244681118148180328478
30365065658095120
1212161616202020
46516064738797112
DxG
B
H
G C
LtL
D
5042 90º Tee - Cemented-Threaded
PFA(PN) WE HZI Lt
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”75x21/2”
90x3”110x4”
14161922263138445161
2227334150617790108132
13171820222226293340
9111417212633404858
4655657898118145170199229
16161616161616161616
1624397012120940562010061620
DxG
EG
L
Z IH
d E
ADAPTOR FITTINGS
7
5052 90º ElbowCemented- Threaded
PFA(PN) WE HZI Lt
14161922263138445161
2227334150617790108132
13171820222226293340
9111417212633404757
344149607490111130154186
16161616161616161616
12183050781653304697751230
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”75x21/2”
90x3”110x4”
DxG
GE
Lt
ZI
I
dEH
5082 Union AdaptorFemale Cemented-Threaded
PFA(PN) WE HLtdxG I
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”75x21/2”
90x3”110x4”
14161922263138445161
34425259727996118132151
13171820222226293340
39465157677993110125145
16161616161616161616
223963871422273185667301213
G
Lt
H
I
d
E
5212 Adaptor Male-FemaleCemented-Male-Threaded
PFA(PN) WC HLtDxdxG B
12121216161620202020
11161719222226303341
16192226313844516169
16161616161616161616
10172760109140190310550590
2230364650658095120130
14161922263138445161
40475161697690101114130
20x16x3/8”25x20x1/2”32x25x3/4”40x32x1”
50x40x11/4”63x50x11/2”
75x63x2”90x75x21/2”110x90x3”125x110x4”
LI
B
D d G C
Lt
H
L1I
z
5062 Adaptor Male-FemaleCemented-Male-Threaded
PFA(PN) WC HLI Lt
1212121216161620202020
1116171922222630334143
1416192226313844516169
1616161616161616161616
1018274264103167190333483720
222430364650658095120130
1214161922263138445161
3744485364698094104122132
16x12x3/8”20x16x1/2”25x20x3/4”32x25x1”
40x32x11/4”50x40x11/2”
63x50x2”75x63x21/2”
90x75x3”110x90x4”125x110x5”
BDxdxG
G C
LtB
H
L
I
Dd
ADAPTOR FITTINGS
8
5222 Bushing Adaptor Male-FemaleCemented-Male-Threaded
PFA(PN) WC HLDxdxG B I Lt
25x20x3/8”32x25x1/2”40x32x3/4”50x40x1”
63x50x11/4”75x63x11/2”
90x75x2”110x90x21/2”125x110x3”
121216161620202020
111617192222263033
192226313844516169
161616161616161616
15255197135185285528545
30364650658095120130
161922263138445161
42505966768697111122
Dd
IL1
H
BLt
CG
Z
5362 Hose Adaptor with ThreadedNut
WE HG3/4”1”
11/4”11/2”
2”21/4”23/4”
16202530405060
6772809197104118
21325469124186260
G
H
E
5452
PFA (PN) WE IdxG Z16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”
23283442526177
14161922263138
1320294892122233
5568101215
16161616161616
45º ElbowCemented-Threaded
z
E
G
d
I
5712 Socket AdaptorCemented-Threadedwith Reinforcing Ring
PFA(PN) WHLtI
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”
C B Z12121212161616
3333444
13171820222226
16161616161616
1120304568102171
25304045556580
14161922263138
30364045525768
dxG
B
z
H
d G C
I Lt
5722 Reducer Adaptor withReinforcing RingMale Cemented-Female Threaded
HB
CG
LtL
D
PFA(PN) WHLtDxG LC B
1718202222
1922263138
1616161616
253671110150
3036506565
1212161616
4650636875
25x1/2”32x3/4”40x1”
50x11/4”63x11/2”
9
ADAPTOR FITTINGS
5752 90º Elbow with Reinforcing RingCemented-Threaded
PFA(PN) WHLtdxG I
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”
E Z13171820222226
9111417212633
344149607490111
16161616161616
14223664100180352
22273341506177
14161922263138
Lt
EG
dE
H
IZ
5742 90º Tee with Reinforcing RingCemented-Threaded
PFA(PN) WHLtdxG
16x3/8”20x1/2”25x3/4”32x1”
40x11/4”50x11/2”
63x2”
E I Z13171820222226
9111417212633
4655657898118145
16161616161616
18274584129224425
22273341506177
14161922263138
d
EG
L
E
H
z I
THREADED FITTINGS
10
5021
PFA(PN) WHLt1GxG1 C B Lt
303636363646464650505065656580809595120120
1212121212161616161616161616202020202020
1313171718171820182022202222222626292933
1718182020222222222222262626292933334040
4041454748535458545958626363666872768786
1616161616161616161616161616161616161616
1718212930525262619968105109109163170223254400406
1/2”x3/8”3/4”x3/8”3/4”x1/2”1”x1/2”1”x3/4”
11/4”x1/2”11/4”x3/4”11/4”x1”11/2x3/4”11/2x1”
11/2”x11/4”2”x1”
2”x11/4”2”x11/2”
21/2”x11/2”21/2”x2”
3”x2”3”x21/2”4”x21/2”
4”x3”
ReducerMale-Female - Threaded
C G
H
G1
Lt1B
Lt
5051 90º Elbow - Threaded
PFA (PN) WHG E Lt3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
2227334150617790108132
13171820222226293340
354250607590111130154186
16161616161616161616
13183052951803685088611225
Lt
G E
H
5041 90º Tee - Threaded
PFA (PN) WHG E Lt3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
2227334150617790108132
13171820222226293340
4655657898118145170199239
16161616161616161616
1624407012124948564411001625
E
G
Lt
H
5011 Socket - Threaded
PFA(PN) WHLtG B
3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
C Z12121212161616202428
2530404555658090108130
13171820222226293340
424581316202326
303640455257687889106
16161616161616161616
1018283964116200200310450
Z
B
CG
H
Lt
THREADED FITTINGS
11
5061 Nipple - Threaded
PFA (PN) WHG C Lt3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
B12121212161616202020
222430364650658095120
11161719222226303341
354547516060688087102
16161616161616161616
101320305667110190290520
H
G C
LtB
5081 Union Female - Threaded
PFA (PN) WHG Lt3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
E34425259727996118132151
39465157677993110125145
224965901452303645707401220
13171820222226293340
16161616161616161616
E G
LtH
Lt1
G
5161 Reducing Nipple - Threaded
PFA(PN) WHGxG1 C LtB
243030383650505050656580809090120120
1212121212161616161616202020202020
1617171919222222222626303033334141
1116111716191722222222222630263330
4146424948575560576364767283799491
1616161616161616161616161616161616
11181727265754636010497170176265251435422
1/2”x3/8”3/4”x3/8”3/4”x1/2”1”x1/2”1”x3/4”
11/4”x3/4”11/4”x1”11/2”x1”
11/2”x11/4”2”x11/4”2”x11/2”
21/2”x11/2”21/2”x2”
3”x2”3”x21/2”4”x21/2”
4”x3”
Lt1G
1 G C
B
H
Lt1 Lt
5071 Cap - Threaded
PFA (PN) WHG C Lt3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
B12121212161616202020
222430364650658095120
13171820222226303340
25293137404045515563
16161616161616161616
91724335387130205375425
Lt
H
GC
B
12
THREADED FITTINGS
5361 Hose Adaptor - Threaded
PFA (PN) WHG C Lt1/4”3/8”1/2”3/4”1”
11/4”11/2”2”
B E1622263036465065
1212121216161616
1216202530405060
49586472849194118
1616161616161616
61218303870107150
1113161719222226
Lt
C G E
B
H
5171 Plug - Threaded
PFA (PN) WHG C Lt3/8”1/2”3/4”1”
11/4”11/2”2”
21/2”3”4”
B222630364650658095120
12121212161616202020
13171820222226303340
25293235434448566171
16161616161616161616
11121633475897160263425
LtB
C G
H
5221
PFA(PN) WHG1xG C LtB Lt1
3/8”x1/2”1/2”x3/4”3/4”x1”1”x11/4”
11/4”x11/2”11/2”x2”
11/2”x21/2”2”x21/2”
2”x3”21/2”x3”21/2”x4”
3”x4”
303646506580809595120120130
121216161620202020202020
171820222226292933334040
404445505260656970748287
161616161616161616161616
1825407080145200210320340410430
111617192222222626303033
Nipple SocketMale-Female - Threaded
C G1 G
Lt1 B Lt
H
545145º Elbow - Threaded
PFA (PN) WG E LtZ3/8”1/2”3/4”1”
11/4”11/2”
2”
23283442526177
5568101215
13171820222226
16161616161616
1320294892122233
EG
ZLt
THREADED FITTINGS
13
5921 Fixed Flange - Threaded
PFA(PN) WZG ELt Dp NH S
1”11/4”11/2”
2”21/2”
3”4”
115140150165185200220
20222226293340
23273239475464
85100110125145160180
14181818181818
4444488
16161616161616
148225276380659670900
351013182124
s
Lt
Dp
G E
H
z
5083 UnionMale-Female - Cemented-Threaded
PFA(PN) WdxG ELt BH CLt1
25”x3/4”32”x1”
40”x11/4”50”x11/2”
63”x2”
1922263138
4045465065
6673677993
1616161616
79109135180310
1722222226
5158727996
1213161616
B Lt
G C
HLt1
E d
5084 Union Male-Female Threaded
PFA(PN) WGxG1 ELt BH CLt1
3/4”x3/4”1”x1”
11/4”x11/4”11/2”x11/2”
2”x2”
1922222226
4045465065
6673677993
1616161616
79109135180310
1722222226
5158727996
1213161616
B
E G1
Lt
G C
Lt1H
14
FITTINGS ACCESSORIES
5480 Nut for Unions: 5080, 5081, 5082,5362, 5083, 5084
PFA (PN) WHø G E1E162025324050637590110
3/4”1”
11/4”11/2”
2”21/4”23/4”31/2”
4”5”
2227364153577493107125
34425259727996118132151
20232527303438465359
16161616161616161616
101827355570105190250430
E1GE
H
5581 Bushing for Unions: 5081, 50825581 Bushing for Unions: 5081, 5082
PFA (PN) WHG1 ZLt3/4”1”
11/4”11/2”
2”21/4”23/4”31/2”
4”5”
13171820222226293340
9101112162326333639
23262932384552626979
16161616161616161616
101724346595170241300475
3/8”1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
G
H
LtZ
G g
5583 Male Threaded Union Bushfor Items 5083, 5084
PFA (PN) WBG Lt11/4”11/2”
2”21/4”23/4”
1722222226
4045465065
1213161616
1616161616
20346181132
3/4”1”
11/4”11/2”
2”
G1 C
LtB
G1
G C
5680 End for Unions: 5080, 5082, 5083
PFA (PN) WHd I EZ162025324050637590110
14161922263138445161
2333333455
2430394455627897110135
16192225293441485666
16161616161616161616
101420346181132205296473
d E
ZI
H
5580 Bushing for Union 5080
PFA (PN) WHd G ZI162025324050637590110
3/4”1”
11/4”11/2”
2”21/4”23/4”31/2”
4”5”
14161922263138445161
9101010121414181818
23262932384552626979
16161616161616161616
101420346181132205296473
G d
Z I
H
FITTINGS ACCESSORIES
15
5681 End for Unions 5081, 5084
PFA (PN) WHG ELt Z3/8”1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
13171820222226293340
334571215192326
2430394455627897110135
16202225293441485666
16161616161616161616
51016233660105135180310
z
G E
Lt
H
5629 Seal for: 5520, 5362
eDdø2025324050637590110125140160200225
2427324246637590110125140160200220
22222222333333
353844556288104123148166186211245260
D
d
e
5639 O-Ring for Unions: 5080, 5081,5082, 5083, 5084
ed162025324050637590110
161928334449
59.77291100
2.623.533.533.533.533.535.345.345.345.34
ø
S
d
5609 O-Ring for Item 5500
ed2025324050637590110125140160200225
23283640506682101117136152177215241
44455555777777
ø
d
S
VALVES
16
1150 Two Nut Valve - Cemented
WFd ZDN I H KJ16202532405063
14161922263138
10152025324050
43435158688093
717589102120142169
454554667486106
6565737896110129
454555668096118
931032012814756721431
Assembly Instructions page 28
J
H
I ZH
I
d K
1141 Two Nut Valve - Threaded
Assembly Instructions page 28
WFG ZDN I H KJ21/2”
3”4”
445161
6580100
137148173
215250295
128146173
132153185
139165207
200032506300
H
Z ll
kd
J
F
* 1280 with FPM O-Rings
WKd HDN ZI F J16202532405063
14161922263138
10152025324050
43435158688093
717589102120142169
454554667486106
6565737896110129
454555668096118
931032012814756721434
Bistop Valve - Cemented1250/1280*
Assembly Instructions page 28
H
Z ll
kd
J
F
Assembly Instructions page 28
WFd ZDN I H KJ7590110
445161
6580100
137148173
215250295
128146173
132153185
139165207
200032506300
1140 Two Nut Valve - Cemented
H
Z ll
kd
J
F
Bistop Valve - Cemented1240/1270*
WKd HDN ZI F J7590110
445161
6580100
137148173
215250295
128146173
132152185
139165207
200032506000
* 1270 with FPM O-RingsAssembly Instructions page 28
H
Z ll
kd
J
F
1151 Two Nut Valve - Threaded
WFG ZDN Lt H KJ12151619222226
10152025324050
474557647698117
717589102120142169
454554667486106
6565737896110129
454555668096118
951052042844796811439
3/8”1/2”3/4”1”
11/4”11/2”
2”
Assembly Instructions page 28
J
F
Lt ZH
G K
Lt
VALVES
17
1251/1281* Bistop Valve - Threaded
* 1281 with FPM O-RingsAssembly Instructions page 28
WKG HDN Z F JLt10152025324050
3/8”1/2”3/4”1”
11/4”11/2”
2”
12151619222226
474557647698117
717589102120142169
454554667486106
6565737896110129
454555668096118
951052042844796811439
J
F
Lt ZH
Lt
G K
1241/1271* Bistop Valve - Threaded
KJG Zd I H FDN7590110
21/2”3”4”
6580100
445161
137148173
215250295
128146173
132152185
139165207
200032506000
W
* 1271 with FPM O-RingsAssembly Instructions page 28
H
Z ll
kG
J
F
1340 One Nut Valve - Cemented
Assembly Instructions page 31
WKHZI Fd445161
137148173
215250295
128146173
132153185
139165207
180028505300
7590110
DN6580100
J
J
FK d
Z
H
II
d
1341 One Nut Valve - Threaded
Assembly Instructions page 31
WKHZLt FG445161
137148173
215250295
128146173
132153185
139165207
200032506300
21/2”3”4”
DN6580100
J
J
FK G
Z
H
Lt
G
Lt
1350 One Nut Valve - Cemented
WFd ZDN I H KJ16202532405063
14161922263138
10152025324050
41414955647690
69738799116138166
454554667486106
6565737896110129
454555668096118
85901592223765361109
Assembly Instructions page 29
J
F
Kd
IZH
I
1351 One Nut Valve - Threaded
WFG ZDN Lt H KJ12151619222226
10152025324050
414355617294114
69738799116138166
454554667486106
6565737896110129
454555668096118
86911612253805461132
3/8”1/2”3/4”1”
11/4”11/2”
2”
Assembly Instructions page 29
J
F
Kd
IZH
I
WFG ZDN Lt H KJ12151619222226
10152025324050
5557687990108133
67728498112130159
454554667486106
6565737896110129
454555668096118
76821502143595041086
3/8”1/2”3/4”1”
11/4”11/2”
2”Assembly Instructions page 29
J
FG
LtZH
Lt
G K
1361 One Nut ValveMale-Female - Threaded
WKHDN ZLt F J1/2”x203/4”x251”x32
11/4”x4011/2”x50
2”x63
Gxd Lp151619222226
152025324050
405053678295
5758658590109
112124137174194230
4554667486106
65737896110129
4555668096118
1282123085317531463
Assembly Instructions page 30
J
KG
LtZH
Lp
dF
1379 One Nut Valve -Female - Threaded Compression
WKFDN ZLt J3/8”1/2”3/4”1”
G H12151820
10152025
35353943
59627382
38404859
50556070
45455566
7878110190
GF
Lt ZH
Lt
Z
KG
1451 Agrifit One Nut ValveThreaded Female-Female
WKFDN ZLt J3/8”1/2”3/4”1”
G H12161820
10152025
47515562
59627382
38404859
50556070
45455566
7878110180
Lt
FG
G K
J
ZH
1461 Agrifit One Nut ValveThreaded Male-Female
18
VALVES
19
CHECK VALVES
10602/10001
10803/10904Check Valve - Cemented
*
Assembly Instructions page 30
1 1000 with FPM O-ring
2 1060 with EPDM O-ring3 1080 with PTFE coated spring + EPDM O-rings4 1090 with PTFE coated spring + FPM O-rings* Sizes 75, 90 and 110 are larger size valves with a different structure
WKHDN ZI Fd14161922263138445161
101520253240506580100
43435158688093137148173
717589102120142169215250295
23232937445465108125148
454555668096118139165207
90901452454106901170181030155540
162025324050637590110
H
IZI
K d
F
K d
lHZ l
F
Knocker Tee - Cemented5048
PFA (PN) WHd Z32405063
I23273238
85101123149
135206281544
39475973
10101010
d
I Z IH
10612/10011
10813/10914Check Valve - Threaded
*
WKHDN ZLt F12161720232327323542
101520253240506580100
474557647698117137148173
717589102120142169215250295
23232937445465108125148
454555668096118139165207
951052042844796811439185030555600
G3/8”1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
1 1001 with EPM O-ring2 1061 with EPDM O-ring3 1081 with PTFE coated spring + EPDM O-rings4 1091 with PTFE coated spring + EPM O-rings* Sizes 21/2, 3 and 4 are larger size valves with a different structureAssembly Instructions page 30
H
LtZLt
K G
F
K d
lHZ l
F
CHECK VALVES
20
1640/16001 Foot Valve - Cemented
*
WKHDN ZI Fd14161922263138445161
101520253240506580100
43435158688093137148173
717589102120142169215250295
23232937445465108125148
454555668096118139165207
93931552654657851355210035006415
162025324050637590110
1 1600 with FPM O-Rings* Sizes 75, 90 and 110 are larger size valves with a different structure
Assembly Instructions page 30
Kd
IzH
II
H zI
F
d
K
1641/16011 Foot Valve - Threaded
*
Lt
H zLt
F
G
K
K
G
LtzH
Lt
WKHDN ZLt FG12151619222226445161
101520253240506580100
474557647698117137148173
717589102120142169215250295
23232937445465108125148
454555668096118139165207
951052042844796811439220036006600
3/8”1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
1 1601 with FPM O-Rings* Sizes 21/2, 3 and 4 are larger size valves with a different structure
Assembly Instructions page 30
21
AIR RELEASE VALVES
1630/16901 Air Release Valve -Cemented
1 1690 with FPM O-Rings* Sizes 75, 90 and 110 are larger size valves with a different structureAssembly Instructions page 30
*
WKHDN ZI Fd14161922263138445161
101520253240506580100
43435158688093137148173
717589102120142169215250295
23232937445465108125148
454555668096118139165207
88881452404056801145210035006415
162025324050637590110
dK
I IZ
H
F
H
Z II
d k
d
1631/16911 Air Release Valve -Threaded
WKHDN ZLt F12151619222226445161
101520253240506580100
474557647698117137148173
717589102120142169215250295
23232937445465108125148
454555668096118139165207
88881452404056801145220036006600
3/8”1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
*
1 1691 with FPM O-Rings* Sizes 21/2, 3 and 4 are larger size valves with a different structureAssembly Instructions page 30
dK
I IZ
H
F
H
ZLt
G k
Lt
22
VALVES ACCESSORIES
1110 Valve Collar - Cemented
K33334050617394119143165
H20202226303442475667
I14161922263138445161
d162025324050637590110
H
K d
I
1112/1113 Blue/Red Handles
L2L1HE L393944475866778194120
26262931384452556980
6565737896110129136163200
22222529303440515861
22222628323642465358
16/3/8”20/1/2”25/3/4”32/1”
40/11/4”50/11/2”
63/2”75/21/2”
90/3”110/4”
ø
LL1 L2
HEPLASSON
OPEN
CLOSE
1114 Valve Nut
WHE E11616274675133198275428900
18182126293640505968
454555668096118139165205
2929344152657996118145
162025324050637590110
ø
H
E G E1
1111 Valve Collar - Threaded
K33334050617394119143165
H20202226303442475667
Lt12161720232327323542
G3/8”1/2”3/4”1”
11/4”11/2”
2”21/2”
3”4”
H
GK
Lt
23
VALVES ACCESSORIES
11151/11212
11263/11274Set of 0-Rings
11212 - Set of EPDM O-Rings for 1280/128111274 - Set of EPDM O-Rings for 1350/1351/1361/1379
9.25X1.78Type 1Type 2
9.25X1.7816/3/8” 20/1/2”
12.37X2.629.25X1.78
25/3/4”
12.37X2.629.25X1.78
32/1”15.88X2.6212.42X1.78
40/11/4”
18.72X2.6212.42X1.78
50/11/2”
22.22X2.6215.88X2.62
63/2”18.72X2.62
75/21/2”
20.22X3.5390/3”
23.04X3.53110/4”
1
valve code 1150/1valve code 1250/1valve code 1350/1valve code 1379
Dia16-2016-2016-20
20
1
2
valve code 1150/1valve code 1250/1valve code 1350/1
Dia75-11075-11075-110
1
valve code 1150/1valve code 1250/1valve code 1350/1valve code 1361valve code 1379
Dia25-6325-6325-6325-6325-63
O-Ring For Stem
18.72X2.6217.5X1.5
Type 1Type 2Type 3
16/3/8” 20/1/2” 25/3/4” 32/1” 40/11/4” 50/11/2” 63/2” 75/21/2” 90/3” 110/4”
valve code 1350/1valve code 1361
valve code 1379valve code 1150/1valve code 1250/1
O-Ring For Body
18.72X2.6217.5X1.5
19.20X3.00
25.07X2.6223.52X1.7824.00X4.00
29.75X3.5329.87X1.7831.00X5.00
37.69X3.5336.14X2.6239.00X6.00
47.00X5.3445.69X2.6249.00X7.00
59.70X5.3458.42X2.6262.00X7.00
69.22X5.3469.85X3.53
81.92X5.3485.32X3.53
104.10X5.34101.20X3.53
18.72X2.6217.5X1.5
22.22X2.6222.22X2.62
Type 1Type 2Type 3Type 4
16/3/8” 20/1/2” 25/3/4” 32/1” 40/11/4” 50/11/2” 63/2” 75/21/2” 90/3” 110/4”
O-Ring For Spacing
valve code 1250/1valve code 1150/1valve code 1350/1valve code 1361valve code 1379
18.72X2.6217.5X1.5
22.22X2.6222.22X2.62
25.07X2.6223.52X1.7828.30X2.6228.30X2.62
29.75X3.5329.87X1.7837.69X3.5336.14X2.62
37.69X3.5336.14X2.6247.63X3.5345.69X2.62
47.69X5.3445.69X2.6257.15X3.5358.42X2.62
59.70X5.3458.42X2.6271.44X3.5371.44X3.53
69.22X5.3469.85X3.5391.67X3.5391.67X3.53
81.92X5.3485.32X3.53113.90X3.53113.90X3.53
104.10X5.34101.20X3.53142.50X3.53142.50X3.53
11151 - Set of EPDM O-Rings for 1250/125111263 - Set of EPDM O-Rings for 1150/1151
e
d
TECHNICAL SPECIFICATIONS - FITTINGS
Product Description
DESCRIPTION -Precision moulded pressure pipe fittings and flanges made fromPVC-UH suitable for PVC pipe systems up to 16 bar. Ourcomprehensive range of items and sizes can be joined eitherby cold solvent cementing or through threading.
Sizes and dimensions conform to international standard.
All fittings are suitable for potable water, beverges, and foodcontact, as well as corrosive* fluid transports.
* For specific chemicals, please consult your sales rep.
STANDARDS -Products conform to the requirments of ISO 264, 727, 2536,3460, KIWA Criteria Std. Nr. 54 and DIN 8063, 19532, UNI EN1452-3, AFNOR 54-029 and 54-028.
MATERIALS -PVC-UH unplasticized poly (vinyl chloride) meeting the abovementioned Standards.
Injection-moulded components: PVC-UH.Metal reinforced rings: on the female threads INOX AISI 430.Gaskets and O-Rings: EPDM.
MARKINGS -The fittings and valves incorporate the following informationmoulded in relief:PLASSON Trade Mark (registered in most countries)Diameter of connectionNominal pressureType of Material
COLOUR -All fittings and valves are grey, in accordance with PVC-Upressure pipeline standards.
ITEMS -Sockets, 45o and 90o Elbows, 90o Tees, Bushes, Unions,Reducers, Adaptors, Hose Nozzles, Caps, Plugs, Nipples,Flanges, Flange Adaptors, Ball Valves, Foot Valves, CheckValves, and Air Release Valves.
SANITARY LAWS -The PLASSON fittings and valves conform to the sanitary lawsand regulations in force in the various European Countries andin the U.S. relating to transportation of potable water, wine,beverages and food.
APPLICATION FIELDS -Potable water systems, irrigation systems (including fertilization),installation for wine, beer, beverages and other fluids, industrialplants, conveyence of acids, bases, salts, fresh or swimmingwater, ship installlations. (for special installations, please contactyour Plasson supplier).
JOINTING TYPES -The fittings and the valves are available with three types ofconnections:Plain ends for solvent cement jointing to pressure pipes of metricdimensions.Fourth digit in the catalogue no. is “O” (XXXO).
Threaded ends to be screwed onto BSP threaded pipes/fittings.Fourth digit in the catalogue no. is “1” (XXX1).
A combination of ends (”adaptor fittings”) suitable for joining aPVC pipeline of the metric dimensions to a BSP threaded pipe,fitting, valve or accessory (PVC or other materials).Fourth digit in the catalogue no. is “2” (XXX2).
SIZES -For standard pipes of the ISO metrical range: 12, 16, 20, 25,32, 40, 50, 63, 75, 90, 110, 125, 140, 160, 200, 225mm.
And for pipes of the BSP threaded range: 1/4”,3/8”,
1/2”, 3/4”, 1”, 11/4”, 1
1/2”, 2”, 21/4”, 3”, 4” ,5”.
THREADS -PLASSON fittings are female threaded (cylindrical) and malethreaded (conical) in accordance with ISO, BS 21, and UNI 339standards.
FLANGES -PLASSON backing flanges are to be used in connection withthe flange adaptors (catalogue no. 5500, 5510, and 5520). Thenumber, sizes and distance between the centre of the holesconform to UNI 2223, EN 1452-3, ISO 2536 and DIN 8063 forpressure classes of 10-16 Bar.
ACCESSORIES -The fitting range is completed by some accessories such assolvent cement, primer, PTFE tape, etc.
WORKING TEMPERATURES -
* in accordance with EN 805
WORKING TEMP.CELSIUS
1610
14.49
12.88
11.27
106.25
300-350250-300 350-400 400-45000-250
PFA* (PN) BarPFA* (PN) Bar
24
25
TECHNICAL SPECIFICATIONS - FITTINGS
PRESSURES -The fittings and valves, in accordance with EN 805 standard,have three working pressures: PTA (PA), PMA and PEA.To every PFA values are connected the following PMA and PEA:
PRESSURESIN BAR
16106
2012.57.5
24159
PFA (PA) PMA PEA
PVC PROPERTIES -The following are the required properties for injection mouldedPVC-UH fittings and valves in accordance with ISO-EN-UNIStandards:
CHARACTERISTICSDensity at 23oCVicat 5 Kg.Tensile impact strengthTensile strength at breakElongation at breakYield stressFlexural modulusHeat conductivity at 23oCSpecific heat at 23oCFire resistance (0,85 mm.)
Kg/dm3
oCKJ/m2
MPa%
MPaMPa
W/mKJ/Kg K
ISO 1183ISO 306ISO 527ISO 527ISO 527ISO 527ISO 527
ASTM C 177-
UL 94
UNITS VALUES STANDARDS1.3977
≥ 513≥ 49
≥ 12046
≥ 30000,13-0,19900-1000
V 0
Symbols & Definitions Fittings
PN - Nominal Pressure in Bar - Allowable operating pressureconveying water at 20OC during 50 years.
PFA - Allowable Operating Pressure - Maximum hydrostaticpressure that a component is capable of withstandingcontinuously in service (EN 805:1999); for water at temperaturesup to 25OC: PFA=PN.
PMA - Allowable Maximum Operating Pressure - Maximumpressure occurring from time to time, including surge, that acomponent is capable of withstanding in service (EN 805:1999).
PEA - Allowable Site Test Pressure - Maximum hydrostaticpressure that a newly installed component is capable ofwithstanding for a relatively short duration, in order to ensurethe integrity and tightness of the pipeline (EN 805:1999).
MRS : Minimum Required Strength
PVC-U : Unplasticized Poly (vinyl chloride)
PVC-UH : Unplasticized Poly (vinyl chloride) material for injection-moulded components, such as PLASSON fittings and valves,with a proved MRS-value of at least 25Mpa.
EPDM : Ethylene Propylene Rubber
FPM : Fluoride Rubber (VITON)
PTFE : Polytetrafluoroethylene
ABBREVIATIONS USED IN THIS CATALOGUE -
d, d1
G, G1
DND, D1
E, E1
l, l1L, L1, L2
Lt, Lt1
ZCBDpSNeHW
Nominal inside diameterNominal size of thread in inchesNominal boreOutside diameterMaximum overall external diameterInternal length of cementingExternal length for cementingLength of threadLength from pipe stop to centre/other pipe stopExternal size of octagonLength of rimPitch circle diameter of bolt holes in flangesDiameter of bolt holes in flangesNumber of bolt holes in flangeCross section diameter of O-RingTotal lengthWeight in grams
Product Description
1 5 10 25 50
0
5
10
15
20
25
Pre
ssu
re in
bar
s
Time in years
10°C20°C
30°C
40°C
50°C
60°C
Permissable Working Pressures in Accordance with DIN8062
TECHNICAL SPECIFICATIONS - VALVES
Product Description
DESCRIPTION -Precision moulded valves made from uPVC suitable for linepipe systems up to 16 bar. Our comprehensive range of itemsand sizes can be connected either by cold solvent cementingor through threading.
Sizes and dimensions conform to international standards.
All valves are suitable for potable water, beverages, food as wellas corrosive fluid transport.
MATERIALS -PVC-UH (unplasticized polyvinyl chloride) meeting the standardsof DIN-BS-UNI-AFNOR, KIWA, etc
O-Rings -1) EPDM (ethylene-propylene copolymer). Hardness: 60 shore, unless otherwise specified2) FPM (Fluorised-Rubber) Hardness: 60 shore, unless otherwise specified
Springs -1) PTFE coated stainless steel 316 core2) Coated Springs: Teflon coated on stainless steel 316 core
Gaskets (on ball) -1) PTFE (Polytetra Fluorised-Ethylene)2) PE
MARKINGS -The valves incorporate the following information moulded inrelief:Plasson Trade Mark (registered in most countr ies)Diameter of connectionNominal pressureType of Material
COLOUR -All valves are grey, in accordance with PVC-U pressure pipelinestandards.Handles are blue or red.
ITEMS -Ball Valves, Check Valves, Foot Valves, Air Release Valves
SANITARY LAWS -The PLASSON valves conform to the sanitary laws andregulations in force in the various European Countries and inthe U.S. relating to transportation of potable water, wine,beverages and food.
APPLICATION FIELDS -Potable water systems, irrigation systems (including fertilization),installation for wine, beer, beverages and other fluids, industrialplants, conveyence of acids, bases, salts, fresh or swimmingwater pool, ship installlations. (for special installations, pleasecontact your Plasson supplier).
JOINTING TYPES -The valves are available with three types of connections:Plain ends for solvent cement jointing to pressure pipes of metricdimensions.Fourth digit in the catalogue no. is “O” (XXXO).
Threaded ends to be screwed onto BSP threaded pipes/fittings.Fourth digit in the catalogue no. is “1” (XXX1).
SIZES -For standard pipes of the ISO metrical range of mm: 16, 20, 25,32, 40, 50, 63, 75, 90, 110
And for pipes of the BSP threaded range: 1/2”, 3/4”, 1”, 11/4”, 1
1/2”,2”, 21/2”, 3”
THREADS -PLASSON valves are female threaded (cylindrical) and malethreaded (conical) according with ISO 7, UNI 339, DIN 2999and BS 21 standards.
MECHANICAL PROPERTIES -Maximum working pressure in bars:∆16-63: PN16∆75-110: PN10
PVC PROPERTIES -The following are the required properties for an injection mouldedPVC fittings withstanding pressures PN16 in accordance withUNI standards:
26
CHARACTERISTICSDensityVicat (50N)Yield stressTensile Strength at break (230)Elongation at breakTensile Modulus
Kg/m3
oCMPaMPa%
MPa
ISO 1183ISO 306-BISO 527ISO 527ISO 527ISO 527
UNITS VALUES STANDARDS1.47645401203000
IZOD ImpactStrength
23o C0o C
-20o C
27015070
Unnotched(j/m)
NBNB
>1500
ASTMD256
ISO180
Notched(j/m)
TECHNICAL SPECIFICATIONS - VALVES
Product Description
ADDREVIATIONS USED IN THIS CATALOGUE -
dFGJKDN
DILLpLtZHW
Nominal internal diameterDistance from centre of valve to top of handle or valveNominal size of thread in inchesLength of handleOutside diameter or nutNominal bore corresponding approx to the inside diameterof the pipeOutside diameterInternal length for cementingExternal length for cementingInternal length to PE pipeLength of threadLength from pipe stop to centre/other pipe stopTotal lengthWeight in grams
1 5 10 25 50
0
5
10
15
20
25
Pre
ssu
re in
bar
s
Time in years
10°C20°C
30°C
40°C
50°C
60°C
Permissable Working Pressures in Accordance with DIN8062
27
Symbols & Definitions Valves
PN - Nominal Pressure in Bar - Allowable operating pressureconveying water at 20OC during 50 years.
PFA - Allowable Operating Pressure - Maximum hydrostaticpressure that a component is capable of withstandingcontinuously in service (EN 805:1999); for water at temperaturesup to 25OC: PFA=PN.
PMA - Allowable Maximum Operating Pressure - Maximumpressure occurring from time to time, including surge, that acomponent is capable of withstanding in service (EN 805:1999).
PEA - Allowable Site Test Pressure - Maximum hydrostaticpressure that a newly installed component is capable ofwithstanding for a relatively short duration, in order to ensurethe integrity and tightness of the pipeline (EN 805:1999).
MRS : Minimum Required Strength
PVC-U : Unplasticized Poly (vinyl chloride)
PVC-UH : Unplasticized Poly (vinyl chloride) material for injection-moulded components, such as PLASSON fittings and valves,with a proved MRS-value of at least 25Mpa.
EPDM : Ethylene Propylene Rubber
FPM : Fluoride Rubber (VITON)
PTFE : Polytetrafluoroethylene
ASSEMBLY INSTRUCTIONS
28
Instructions for connection to the system -A) Completely unscrew the ring nuts (12) and fit them to thepipe that the valve is to be connected to.B) Either glue or screw couplings (10) at the pipe ends.C) Position the valve boby (5) between the two couplings.D) Lock the ring nuts for both sides.
Instructions for disassembly and reassembly -Completely unscrew the ring nuts (12).Remove the valve body (5) radially.Remove the handle (1) by pulling upwards.Insert the key in its seat in the gasket support (8).Completely unscrew the gasket support (8) by rotating thehandle counter clockwise .Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFEgasket (7*) using a suitable tool in order to prevent damage.Remove the ball (4) which was previously positioned during theclosing phase.Remove the stem (3) by pushing downwards and extracting itfrom inside the valve body.Remove the O-Ring (2*) from the stem (3) using a suitable tool.Remove the O-Ring (9*) and the PTFE gasket (7*) using asuitable tool.To assemble the valve, follow the same procedure in the oppositesequence.
Notes -The valve shall be supplied with a pre-set radial seal, applicableto average operating conditions; due to particular operatingconditions, it might be necessary to follow the instructions belowbefore performing the final step D:1. Disconnected the handle (1) by pulling upwards.2. Insert the key in its seat in the gasket support (8).3. Turn clockwise or counter clockwise to adjust as required.
O-Rings and gaskets which are numbered 2, 6, 7, 9 and 11 are packagedtogether in a set of O-Rings for valves (see Page 23).
Assembly1250/12801251/12811240/12701241/12711140/1141
1150, 1151 Assembly
Instructions for connection to the system -A) Completely unscrew the ring nut (12) and fit them to the pipethat the valve is to be connected to.B) Either glue or screw coupling (10) at the pipe ends.C) Position the valve body (5) between the two couplings.D) Lock the ring nuts for both sides.
Instructions for disassembly and reassembly -Completely unscrew the ring nuts (12).Remove the valve body (5) radially.Remove the handle (1) by pulling upwards.Release the gasket support (8) by pushing the ball (4) throughthe valve while the valve is closed.Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFEgasket (7*) using a suitable tool in order to prevent damage.Remove the ball (4) which was previously positioned during theclosing phase.Remove the stem (3) by pushing downwards and extracting itfrom inside the valve body.Remove the O-Ring (2*) from the stem (3) using a suitable tool.Remove the O-Ring (9*) and the PTFE gasket (7*) using asuitable tool.To assemble the valve, follow the same procedure in the oppositesequence.
O-Rings and gaskets which are numbered 2, 6, 7, 9 and 11 arepackaged together in a set of O-Rings for valves (see Page 23).
ASSEMBLY INSTRUCTIONS
29
Instructions for connection to the system -A) Completely unscrew the ring nut (12) and fit it to the pipethat the valve is to be connected to.B) Either glue or screw coupling and fixed side (5, 10) to thepipe end.C) Lock the ring nut.
Instructions for disassembly and reassembly -Completely unscrew the ring nuts (12).Remove the valve body (5) radially.Remove the handle (1) by pulling upwards.Release the gasket support (8) by pushing the ball (4) throughthe valve while the valve is closed.Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFEgasket (7*) using a suitable tool in order to prevent damage.Remove the ball (4) which was previously positioned during theclosing phase.Remove the stem (3) by pushing downwards and extracting itfrom inside the valve body.Remove the O-Ring (2*) from the stem (3) using a suitable tool.Remove the O-Ring (9*) and the PTFE gasket (7*) using asuitable tool.To assemble the valve, follow the same procedure in the oppositesequence.
O-Rings and gaskets which are numbered 2, 6, 7, 9 and 11 are packagedtogether in a set of O-Rings for valves (see Page 23).
1350, 1351 Assembly
Instructions for connection to the system -A) Completely unscrew the ring nut (12) and fit it to the pipethat the valve is to be connected to.B) Either glue or screw coupling and fixed side (5, 10) to thepipe end.C) Lock the ring nut.
Instructions for disassembly and reassembly -Completely unscrew the ring nuts (12).Remove the valve body (5) radially.Remove the handle (1) by pulling upwards.Release the gasket support (8) by pushing the ball (4) throughthe valve while the valve is closed.Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFEgasket (7*) using a suitable tool in order to prevent damage.Remove the ball (4) which was previously positioned during theclosing phase.Remove the stem (3) by pushing downwards and extracting itfrom inside the valve body.Remove the O-Ring (2*) from the stem (3) using a suitable tool.Remove the O-Ring (9*) and the PTFE gasket (7*) using asuitable tool.To assemble the valve, follow the same procedure in the oppositesequence.
O-Rings and gaskets which are numbered 2, 6, 7, 9 and 11 are packagedtogether in a set of O-Rings for valves (see Page 23).
1361 Assembly
ASSEMBLY INSTRUCTIONS
30
Instructions for connection to the system -Completely unscrew the ring nuts (12) out of the body, extractthe gasket support of the valve (16) from the body making surethe spring assisted piston (14) dose not fall out.To replace valve, reverse the procedure, being careful to set theO-Ring properly and grease it with silicon grease.
1630/1690/1631/16911640/1600/1641/1601
Assembly
Instructions for connection to the system -Completely unscrew the ring nuts (12) out of the body, extractthe gasket support of the valve (16) from the body making surethe spring assisted piston (14) dose not fall out.To replace valve, reverse the procedure, being careful to set theO-Ring properly and grease it with silicon grease.
1060/1000/1080/1090 Assembly1061/1001/1081/1091
1379 Assembly
Instructions for connection to the system -A) Connect PE pipe to the compression nut (19).B) Completely unscrew the ring nut (12) and fit it to the pipethat the valve is to be connected to.C) Either glue or screw coupling and fixed side (5, 10) to thepipe end.D) Lock the ring nut.
Instructions for disassembly and reassembly -Completely unscrew the ring nuts (12).Remove the valve body (5) radially.Remove the handle (1) by pulling upwards.Release the gasket support (8) by pushing the ball (4) throughthe valve while the valve is closed.Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFEgasket (7*) using a suitable tool in order to prevent damage.Remove the ball (4) which was previously positioned during theclosing phase.Remove the stem (3) by pushing downwards and extracting itfrom inside the valve body.Remove the O-Ring (2*) from the stem (3) using a suitable tool.Remove the O-Ring (9*) and the PTFE gasket (7*) using asuitable tool.To assemble the valve, follow the same procedure in the oppositesequence.
O-Rings and gaskets which are numbered 2, 6, 7, 9 and 11 arepackaged together in a set of O-Rings for valves (see Page 23).
ASSEMBLY INSTRUCTIONS
31
Instructions for connection to the system -A) Completely unscrew the ring nuts (12) and fit it to the pipethat the valve is to be connected to.B) Either glue or screw coupling (10) at the pipe ends.C) Position the valve body (5) between the two couplings.D) Lock the ring nuts for both sides.
Instructions for disassembly and reassemble -Completely unscrew the ring nuts (12).Remove the valve body (5) radially.Remove the handle (1) by pulling upwards.Insert the key in its seat in the gasket support (8).Completely unscrew the gasket support (8) by rotating thehandleanticlockwise.Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFEgasket (7*) using a suitable tool in order to prevent damage.Remove the ball (4) which was previously positioned during theclosing phase.Remove the stem (3) by pushing downwards and extracting itfrom inside the valve body.Remove the O-Ring (2*) from the stem (3) using a suitable tool.Remove the O-Ring (9*) and the PTFE gasket (7*) using asuitable tool.To assemble the valve, follow the same procedure in the oppositesequence.
Notes -The valve shall be supplied with a pre-set radial seal, applicableto average operating conditions; due to particular operatingconditions, it might be necessary to follow the instructions belowbefore performing the final step D:1. Disconnected the handle (1) by pulling upwards.2. Insert the key in its seat in the gasket support (8).3. Turn clockwise or anticlockwise to adjust as required.
O-Rings and gaskets which are numbered 2, 6, 7, 9 and 11 are packagedtogether in a set of O-Rings for valves (see Page 23).
1340/1341 Assembly
Reliable links build a durable piping network.Rely on Plasson’s fittings for long term system performance.
The World’s Most Dependable Fittings
PLASSON Ltd. Maagan Michael D.N. Menashe 37805 Israel, Tel: +972-4-6394711Fax: +972-4-6390887, E-mail: [email protected], www.plasson.com
The World’s Most Dependable Fittings
Pus
hup
972-
4-62
4345
6