CASS HUDSON CO. Installation Instructions Dream Dinette HUDSON CO. Dream Dinette Attach Mechanism to...
Transcript of CASS HUDSON CO. Installation Instructions Dream Dinette HUDSON CO. Dream Dinette Attach Mechanism to...
CASS HUDSON CO.Installation Instructions Dream Dinette
(Window Version)
CASS HUDSON CO.IMPORTANT
Ensure assembly is square, straight, and centered throughout installation process.
Vehicle wall must be reinforced prior to installation of Dream Dinette.
Slotted holes are used in order to allow for adjustment during the installation process. Once the mechanism is installed properly the remaining holes should be used to secure the mechanisms in place.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.Dream Dinette
Table Top Preparation
• Strike a centerline down the middle of the table top.
centerline
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.Dream Dinette
Attach Mechanism to Table Top
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
• Unfold dinette mechanism and install two bolts being sure not to over tighten.
• Strut Location for version with 22” mounting plate.
• This location is not used in this design.
• Strut Location for version with 25.5” mounting plate.
• Turn mechanism over on to table top.
CASS HUDSON CO.Dream Dinette
Attach Mechanism to Table Top
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.Dream Dinette
Attach Mechanism to Table Top continued• Align mechanism so
that it is centered and flush to the edge of the table top.
• Ensure that the mechanism is square, straight, and centered to table top then secure using all 8 hole locations.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.Dream Dinette
Attach Slide Track and Lock Bar• Place slide track in center of
table top and adjust such that the slide block covers approximately 1/3 of the lock bar window.
• Secure slide track into place using slotted holes.
• Firmly press lock bar into place and secure using hardware. Be sure the lock bar is parallel with the slide track and the hardware is as far apart as possible in order to insure proper operation of lock.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
CASS HUDSON CO.Dream Dinette
Mount Assembly
• Mount assembly to wall being sure to utilize all 13 mounting holes.
This document is the property of CASS HUDSON CO. It shall not be copied or duplicated in any manner without the written consent of CASS HUDSON CO.
DRAWNCHECKEDENG APPRMGR APPR
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN INCHES
ANGLES ±0.5°2 PL ±0.03 3 PL ±0.010
NAMEdarrens
DATE07/19/07
CASS HUDSON COMPANYCOME ROLL WITH US
TITLE
SIZEB
DWG NO REV
FILE NAME: 255X15.dft
SCALE: WEIGHT:
REVISION HISTORYREV DESCRIPTION DATE APPROVED
SHEET OF1 1
SPECIAL NOTICETHIS DRAWING IS THE PROPERTY OF CASS HUDSON CO. IT SHALL NOT BE COPIED OR DUPLICATED IN ANY MANNER, AND SHALL NOT BE SUBMITTED TO OUTSIDE PARTIESFOR EXAMINATION WITHOUT OUR WRITTEN CONSENT. IT SHALL BE USED WITH REFERENCE TO WORK UNDER CONTRACT OR PROPOSALS SUBMITTED BY CASS HUDSON CO.
NOTES:UNLESS OTHERWISE SPECIFIED
DDT255X15 A
DREAM DINETTE
A PRODUCTION RELEASE 07.19.07 DLS
29.4
11
25.5
3836
15