CAN-bus Keypads for Off-Highway Vehicles ANSI/ASAE EP455 5.12 +/- 25kV for 10 pulses, 5 of each...

CAN-bus Keypads

CAN-bus Keypads forOff-Highway Vehicles• Five standard keypad form factors available

• J1939 and CANopen versions

• Dimmable LED indicators and legends

• Sealed to IP67

• Vibration and impact resistant

• Operating temp: -40oC to +85oC

• Long life: 1,000,000 cycles per key

• Support for multiple key press combinations

• Designed for 12/24 volt systems

• Custom legends and configurations available

3K SERIES KEYPADSCUSTOM OPTIONSContact Grayhill to build your custom part number

• Custom keytop legends

• Up to 3 LED indicators per key

• Indicator colors: Red, Amber, Green, Blue

• Custom backlight colors: Red, Amber, Green

• Factory configured parameters

Your Experts in Cab ControlsGrayhill specializes in the design, development and production of human interface controls, including:- Cab user interface design- Customized control panels- CAN-bus interface devices

www.grayhill.com

DIMENSIONS in inches (and millimeters)ISO Symbols shown in dimensional drawings

4 x 5 Keypad

3 x 5 Keypad Panel cut-out geometry for 4x5 and 3x5 keypads.

Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com

CONNECTION4 pin Deutsch DT Connector.Power with 8V to 32V vehicle type inputs.

Pin 1: Power

Pin 2: Ground

Pin 4: CAN L

Pin 3: CAN H

STANDARD LEGEND SETS

MOUNTING INFOUse M6 Nut (1mm pitch)

Max Torque 25 in-lbs

4 x 3 Keypad

4 x 2 Keypad

DIMENSIONS in inches (and millimeters)

Grayhill, Inc. • 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com

Panel cut-out geometry for 4x3 keypad.



2 x 4 Keypad


2 x 3 Keypad

ENVIRONMENTAL TESTING STANDARDSOperating temperature, High ANSI/ASAE EP455 5.1.1

Level 2+85°C for 11 hours

Operating temperature, Low ANSI/ASAE EP455 5.1.1 Level 2

-40°C for 4 hours

Storage Temperature, High ANSI/ASAE EP455 5.1.2 Level 2

+85°C 4 hours

Storage Temperature, Low ANSI/ASAE EP455 5.1.2 Level 2

-40°C 4 hours

Thermal Shock ANSI/ASAE EP455 5.1.3 -40°C to 70°C at a rate of 4°C/min (1 hour at extremes)

Altitude (Barometric Pressure) ANSI/ASAE EP455 5.2 101.3kPa to 18.6kPa

Sand and Dust ANSI/ASAE EP455 5.3 24 hours with 0.88g/m3

Solar Radiation ANSI/ASAE EP455 5.4 43 to 75W/m2 UV Radiation (280 to 400nm wavelength) for 300h

Wash Down ANSI/ASAE EP455 5.6 Level 2 375 kPa and 8.3 L/min for 10 minutes @15°C Water temp

Ingress Protection IP67 1 meter submersion for 30 minutes

Humidity ANSI/ASAE EP455 5.13 96% Humidity at 35°C for 240 hours.

Salt Fog ANSI/ASAE EP455 5.9 5% aqueous solution of NaCl @ 35°C and a pH between 6.5 and 7.2 for 48 hours

Chemical resistance (Resis-tance to Solvents)

ISO 16750-5 EP 455 (5.8.2)

Thermal Cycling (Change of Temperature)

ISO 16750-4 -40° to 85°C 2 hours at ex-tremes change rate = 1°C/min (8 hours) repeat for 30 cycles.

PHYSICAL TESTING STANDARDSVibration, Random ANSI/ASAE EP455 5.15.1 2 hours each axis @ 52.4 m/s2

RMS overall acceleration and spectral power density of 2m2/s3 from 50Hz to 2000Hz

Vibration, Sinusoidal ANSI/ASAE EP455 5.15.2 A logarithmic sweep from 10Hz to 2000Hz to 10Hz over a period of 20 minutes for 4 hours in each of 3 orthogonal axes with amplitude of 1.5mm from 10Hz to 40Hz and a constant acceleration of 35m/s2 RMS from 40Hz to 2000Hz.

Shock / Crash Safety ANSI/ASAE EP455 5.14 A single 11ms half sine pulse of 490 m/s2 in 3 perpendicular axes.

Drop ANSI/ASAE EP455 5.14.2 Level 1

Drop component 400 mm onto a hardwood benchtop on all practi-cal edges.

Shipping integrity International Safe Transit Agency procedure 3A

ELECTROMAGNETIC COMPATIBILITY STANDARDSESD ANSI/ASAE EP455 5.12 +/- 25kV for 10 pulses, 5 of

each polarity

Radiated Immunity ISO14982 6.6 10MHz-1000MHz Range 48mA Bulk Current Injection 100V/m

Conducted Emissions SAE J1113-41, Control/Signal lines only

Class 3 for 3K120-4RC3AG, 3K108-2RC3AG.Class 4 for 3K115-3RC3AG, 3K112-4RC3AG, 3K108-4RC3AG

Broadband Radiated Emissions ISO14982 6.4 64dB to 54dB, 30MHz-75MHz (linearly decreases) 54dB to 65dB, 75MHz-400MHz (linearly increases) 65dB, 400MHz-1000MHz

ELECTRICAL PERFORMANCE STANDARDSMaximum load ANSI/ASAE EP455 5.1.1

Level 2 -40°C 4 hours +85°C for 11 hours max load applied

Jump start forward voltage ISO 16750-2 36V for 60 minutes

Jump start reverse voltage ISO 16750-2 -36V for 60 minutes

Short circuit protection ISO 16750-2 All outputs to ground for 60s

Reverse polarity protection ISO 16750-2 28V for 60s

Starting profile ISO 16750-2 12V class B, 24V class A

Battery-less operation ANSI/ASAE EP455 5.11.3 Level 2

Apply 6+12.6sin(2*pi*f*t) f is swept from 500Hz to 1.5kHz 5min

Load dump ISO 7637-2 Test Pulse 5b Class A

Switching spikes – negative ISO 7637-2 Test Pulse 3a Class A

Switching spikes – positive ISO 7637-2 Test Pulse 3b Class A

Wire harness inductance ISO 7637-2 Test Pulse 2a and 2b

Class A

+/- inductive load pulse ANSI/ASAE EP455 5.11.4 14-300e^(-t/.001)V 1Hz for 300 cycles

+/- mutual coupling ANSI/ASAE EP455 5.11.6 Level 2

14+200e^(-t/14x10^-6)V 1Hz for 300 cycles

Alternator field decay ANSI/ASAE EP455 5.11.2 Class A

Bulletin 1123Rev 06/14

CE COMPLIANCEAgriculture and Forestry Machinery EMC

ISO 14982 ESA

Construction Machinery EMC EN 13309:2000 ESA

www.grayhill.com

ORDERING INFORMATION CUSTOMIZATION OPTIONS

Contact Grayhill to build your custom part number• Custom keytop legends

• Up to 3 LED indicators per key

• Indicator colors: Red, Amber, Green, Blue

• Custom backlight colors: Red, Amber, Green

• Factory configured parameters

3K X X X - X R C 3 A GSeries Code

Keypad Symbols 0 = Blank 1 = ISO Symbols (as shown above) 2 = Targets (8-key only)

Key Quantity08 (2 or 4 row), 12 (4 row), 15 (3 row), 20 (4 row)06 (2 row)

Default

Comm Protocol C = J1939 N = CANopen

Key Material R = Rubber

Rows: 2, 3, 4

www.grayhill.com

Functions as an engine monitor or input device.

• Intuitive touch technology to selectobjects and swipe through screens.

• Responsive PCAP touchscreen recognizes bare and gloved fingers, even when the display surface is wet.

• Easy application creation and integration with VUI Builder or Qt.

• Scratch resistant/anti-glare coverglass is optically bonded to LCD displayfor superior mechanical and visualperformance.

• Bright, backlit display provides highcontrast text and full color graphicsfor excellent sunlight readability.

• Convenient flush mounting providesmodern look and feel, to seamlesslyblend with vehicle cab design.

• Armrest, A-post, and dashboardmounting.

• Rugged design for extreme environments.

Versatile CAN-Based DisplayThe Series 3D50 5-inch Touchscreen Display for off-highway vehicles.

Construction Agriculture

• Powerful processor with 3 second boot time.

Versatile Display. Many Features.

Flexible. Series 3D50 is available with or without a projected capacitance touch screen. This advanced touchscreen works even when wet or when the user is wearing gloves.

Rugged. The protective cover lens is scratch resistant glass, not plastic. Optical bonding of the cover glass improves impact resistance.

Bright. This 5.0-inch backlit WVGA LCD (800x480) is very bright (700 nits) providing good daylight readability. It has software controlled LED backlighting and 16 bit color.

Useful. Ideal for agriculture and construction vehicle applications, including virtual gauges, diagnostic menus, engine monitor, operator input, fault indicators and service reminders.

Easy to Program. PC-based configuration tools make application development fast and easy. Drag and drop graphics, bitmaps, text with the click of a mouse.

Readable. Optically bonding the display, touch sensor and cover

glass reduces reflections. An anti-glare coating further improves

readability in bright sunlight.

Adaptable. Designed for integration into off-highway vehicles. It functions in 12V/24V operation, boots in 3 seconds and is sealed against the ingress of liquids and dust.

Powerful. The powerful embedded computer can monitor and display many events and camera images simultaneously: - - 800MHz- 512MB RAM- 4GB storage- USB 2.0

Adjustable. There are many system interface options:- Up to two CAN-bus ports

- Up to two NTSC/PAL camera input ports

- Up to four digital inputs- Up to four digital outputs

- One USB 2.0 port- Touchscreen

Grayh i l l , Inc . • 561 H i l lg rove Avenue • LaGrange, I l l i no is 60525-5997 • USA • Phone: 708-354-1040 • Fax : 708-354-2820 • www.grayh i l l . com

Grayh i l l , Inc . • 561 H i l lg rove Avenue • LaGrange, I l l i no is 60525-5997 • USA • Phone: 708-354-1040 • Fax : 708-354-2820 • www.grayh i l l . com

Versatile Display. All the Specifications.

Easily create custom graphic icons, text boxes and active gauge elements that monitor J1939 CAN-bus parameters.• Applications can be developed in Grayhill's proprietary

VUI Builder or in Qt - the most trusted cross platformdevelopment environment.

• A development kit is offered to provide the hardwareand software required to set up a programmer'sworkstation for either tool.

Operating temperature ANSI/ASAE EP455 5.1.1 -30°C to +65°C

Storage Temperature ANSI/ASAE EP455 5.1.2 -40°C to +85°C


Altitude (Barometric Pressure)

ANSI/ASAE EP455 5.2 101.3kPa to 18.6kPa

Sand and Dust SAE J1455

Solar Radiation ISO 4892-2 Method B

Wash Down ANSI/ASAE EP455 5.6 Level 2

Humidity ANSI/ASAE EP455 5.13 96% humidity at 35°C for 240 hours


Chemical resistance ISO 16750-5 EP 455 5.8.2

Ingress Protection IP67 front and rear with mating connector installed

ENVIRONMENTAL SPECIFICATIONS

ESD ANSI/ASAE EP455 5.12 Level 1 (Handling), Level 2 (Powered)

Radiated Immunity EP455 5.16 Level 1

Conducted emissions CISPR25 Level 3

Radiated emissions ISO14982

ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS

Vibration, Random ANSI/ASAE EP455 5.15.1

2h each axis 50Hz to 2000Hz

Vibration, Sinusoidal ANSI/ASAE EP455 5.15.2

A logarithmic sweep from 10Hz to 2000Hz to 10Hz over a period of 20 minutes for 4 hours in each axis

Shock ANSI/ASAE EP455 5.14 11ms half sine pulse of 490 m/s2 in 3 axis


400 mm onto a hardwood benchtop on all practical edges.

MECHANICAL PERFORMANCE

Maximum load ANSI/ASAE EP455 5.1.1 T(min) = -40C; T(max) = +65C

Jump start voltage EP455 5.10.2 36V for 5 minutes; -36V for 5 minutes

Short circuit protection EP455 5.10.4 36V

Reverse polarity protection

EP455 5.10.3 -36V

Starting profile ISO 16750-2:2006-08-01 Code C for 12V, Code E for 24V


Load dump ISO 7637-2:2004 Test Pulse 5a

Level 4

Switching spikes ISO 7637-2:2004

Alternator field decay ANSI/ASAE EP455 5.11.2

ELECTRICAL PERFORMANCE SPECIFICATIONS

CE COMPLIANCE

EMC EN 13309:2010 ESA

Operating Voltage 8VDC to 32VDC reverse polarity and load dump

Power Consumption 5 Watts (typical) with full back light

Standby Current <1ma

Display: 5"/127 mm color transmissive TFT LCD

Resolution: WVGA, 800 x 480 pixels, 16 bit color

Aspect ratio: 16:9

Orientation: Landscape or Portrait

Backlighting: LED, 700 cd/m2 or nits

Microprocessor: Freescale™ i.MX6, 800 MHz

Flash Memory: 4GB eMMC

RAM: 512 MB DDR3

USB: 2.0 host (high speed)

Real Time Clock: Internal non-rechargeable battery backup

CAN: (2) CAN 2.0 B J1939 protocol

RS232: full duplex

Video Input: 2 NTSC/PAL

Inputs: (4) 0-32 VDC discrete digital; 10Hz LPF

Outputs: (4) digital 200 mA switched high side

POWER SPECIFICATIONS

Level 4

SOFTWARE DEVELOPMENT TOOLS

VUI Builder Grayhill's proprietaryapplication for PC

Ideal for engineers that wish to quicklycreate common vehicle functions without coding

Qt Cross platform development app from Digia Plc

Ideal for software developers familiar with coding for human interface applications

CoDeSys IEC 61131-3 Development System

Coming Soon

Your Experts in Cab ControlsGrayhill specializes in the design, development and production of human interface controls, including:• Cab user interface design• Customized control panels• CAN-bus interface devices

Grayhill, Inc.561 Hillgrove AvenueLaGrange, Illinois 60525Phone: (708) 354-1040Fax: (708) 354-2820

Bulletin 1213Rev 2/16www.grayhill.com

DIMENSIONS in inches (and mm)

Weight: 360 grams

144,5[5.689]

99,3[3.909]R7,25

.285[ ]66,8[2.630]

110[4.331]

27[1.063]

45,153[1.778]

42,193[1.661] THREADED FOR M5x0.8 SCREWS, 10.5MM, 4 PLACES

MAX SCREW LENGTH = 10MM + PANEL THICKNESSSEE RECOMMENDED PANEL GEOMETRY

100,3[3.949]AT TOP

145,5[5.728]AT TOP

R x4

AT TOP

7,75.305[ ]

602.362[ ] x45,5

.217[ ]

50,15[1.974]

107,25[4.222]

28[1.102]

28[1.102]

97,61[3.843]

28,61[1.127]

27[1.063]

REF91

REF91

RECOMMENDED PANEL MOUNTING GEOMETRY

SECTION X-X

RS232 USB 2.0 CAN1 CAN2 VIDEO1 VIDEO2 RTC Touch DIG IN DIG OUT DIG I/O

3D50XX-100 X X X 0 0 0

3D50VX-100 X X X X X X X 1 1 3

3D50VT-100 X X X X X X X X 1 1 3

3D50DEV-BASE Development Kit (does not include display)

3D50DEV-100 Development Kit with 3D50VT-100 display

Linux Available upon request

Pin Function Pin Function Pin Function Pin Function Pin Function Pin Function

1 VIN Positive 4 Digital In 7 Digital I/O 10 VIDEO1- 13 CAN1 Hi 16 CAN2 Low

2 VIN Return 5 Digital Out 8 Digital I/O 11 VIDEO2+ 14 CAN1 Low 17 RS232Tx

3 VIN Switched 6 Digital I/O 9 VIDEO1+ 12 VIDEO2- 15 CAN2 Hi 18 RS232Rx

18

12

6 1

7

13

REAR CONNECTOR

Mating Connector:DEUTSCH DT16-18SA-K004

Recommended Mounting Cut Out

VERSATILE DISPLAY. ORDER INFORMATION.

Custom Options Available

• Custom Logo• Icons / screens

pre-loaded

www.grayhill.com

Operating temperature ANSI/ASAE EP455 5.1.1 Level 2: -50°C to +85°C with optional heater -25°C to +85°C without heater

Storage Temperature ANSI/ASAE EP455 5.1.2 Level 2: -50°C to +85°C



Sand and Dust SAE J1455

Solar Radiation ISO 4892-2 Method B

Wash Down ANSI/ASAE EP455 5.6 Level 2



Chemical resistance ISO 16750-5 EP 455 5.8.2

Ingress Protection IP67 with mating connector



The MicroDisplay makes it easy to create screens with custom graphics, text and even gauges that automatically adjust based on J1939 values.

Due to its innovative design, native coding is not required for custom user interfaces. Screens and graphic objects are created with the included PC software tool and stored in the on-board fl ash memory.

When in use the MicroDisplay can be controlled two different ways. First, a vehicle’s ECU (Electrical Control Unit) can send and receive commands to con-trol the display. Second, with the new Menu Object and Screen List Object the display can be programmed to provide stand-alone functionality. The menu object allows users to enter and navigate a menu using the menu key. The Screen List Object allows users to quickly navigate through favorite screens (objects) by pressing one of the right and left arrow buttons.

Graphic MicroDisplay• Easily display custom graphic icons,

text boxes and active gauge elements. - Use PC-based software tools to develop graphic objects - Store graphic objects in on-board fl ash memory - Recall objects at run time via J1939 commands - Recall objects at run time using the menu object - Recall objects at run time using the screen list object

• Controlled via J1939 PGNs - Native coding not required

• Ideal for off-highway vehicle applications

- Virtual gauges - Diagnostic menus - Fault indicators & service reminders

• Rated for off-highway vehicles - Extended operating temperature range: -50º C to +85ºC (with heater) - Protected against the ingress of liquids and dust: IP67 rated seal

• 3.2-inch backlit LCD (256x128) - Excellent daylight readability - Transfl ective LCD with anti-glare - Software controlled RGB backlighting - Four level grayscale graphics

• Custom Options Available - Keypad backlight color - Key colors and legends - Icons/screens pre-loaded

• System Interface - One CAN-bus port - Two 200mA outputs (standard option) - Three discrete inputs (standard option - One RS-485 serial port (custom option)

• Styled to sit next to Grayhill standard 20-button 3K Keypad

www.grayhill.com

Grayhill, Inc.561 Hillgrove Avenue phone: (708) 354-1040LaGrange, Illinois 60525 fax: (708) 354-2820 Bulletin 1144

Rev 07/13

DIMENSIONS

3.2

[81,28]

specifi cations subject to change


2h each axis @52.4m/s2 RMS overallacceleration and spectral power density of 2m2/s3 from 50Hz to 2000Hz


A logarithmic sweep from 10Hz to 2000Hz to 10Hz over a period of 20 minutes for 4 hours in each of 3 orthogonal axes with amplitude 1.5mm from 10Hz to 40Hz and a constantacceleration of 35m/s2 RMS from 40Hz to 2KHz

Shock / Crash Safety ANSI/ASAE EP455 5.14 11ms half sine pulse of 490 m/s2 in 3perpendicular axes


Drop component 400 mm onto a hardwood benchtop on all practical edges.


ESD ANSI/ASAE EP455 5.12 Level 1 +/- 25KV

Radiated Immunity EP455 5.16 Level 1

Conducted emissions SAE J1113-41 Level 4

Radiated emissions ISO14982

ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS

Maximum load ANSI/ASAE EP455 5.1.1 Level 2

Jump start voltage EP455 5.10.2 36V for 60 minutes; -36V for 60 minutes

Short circuit protection EP455 5.10.4 36V

Reverse polarity protection

EP455 5.10.3 -36V

Starting profi le ISO 16750-2 Level II code C, Level IV code A


Load dump ISO 7637-2 Test Pulse 5b Us* = 60V

Switching spikes ISO 7637-2 Test Pulse 3a and 3b


Wire harness inductance-switching

ISO 7637-3 Test Pulse a and b

Inductive load pulse ANSI/ASAE EP455 5.11.4

Mutual coupling ANSI/ASAE EP455 5.11.6 Level 2

Alternator fi eld decay ANSI/ASAE EP455 5.11.2


CONTACT GRAYHILL FOR CUSTOM OPTIONS

PART NUMBER DESCRIPTION3D32XK-200 MicroDisplay with CAN, I/O3D32HK-200 MicroDisplay with CAN, I/O and heater3D32XKR-200 MicroDisplay with CAN3D32HKR-200 MicroDisplay with CAN and heater3D32CABLE-1 MicroDisplay Programming Cable with Power Supply REAR CONNECTOR

0 Function

1 V in Positive

2 V Return

3 RS-485 +

4 RS-485 -

5 Digital in 1

6 Digital in 2

7 Digital in 3

8 Digital out 1

9 Digital out 2

10 CAN shield

11 CAN HI

12 CAN LOW

Mating Connector: DEUTSCH DT06-12SA

www.grayhill.com

MOUNTING INFOUse M6 Nut (1mm pitch)Max Torque 25 in-lbs

CE COMPLIANCEEMC EN 13309:2010 ESA

10.4-inch Display for Vehicles• Ideal for gauges, diagnostic menus and other vehicle functions• Capable of displaying three simultaneous video feeds• Sealed to IP67• J1939 compliant CAN interfaces• Interface with Grayhill 3J Series VDC• Optional touch screen• 7 soft keys for menu selection• Adjustable backlight on soft keys• Bezel mount or RAM mount compatible• Brightness 400 NITS• 16-Bit color TFT• LED backlight• SVGA resolution (800x600)

EMBEDDED COMPUTER • 416 MHz PXA270 processor• 64MB SDRAM• 128MB NAND program, and file system FLASH• Windows CE or Linux Operating System*• Real time clock with 10 year battery backup

INPUT / OUTPUT• 1 USB host port• 3 CAN bus ports• 3 NTSC/PAL video inputs• 2 RS-232 ports• 3 inputs• 2 outputs (200 mA max)• 10/100 ethernet port• Input voltage: 9VDC to 32VDC

CONNECTOR• AMP 776164-1 mating connector• AMP 770520-1 or AMP 770854-1 contacts

CERTIFICATES: CE MARK

PART NUMBER | DESCRIPTION3D104XK-1006 10.4 inch Display, Windows CE63D104TK-1006 10.4 inch, touchscreen, WIN CE6

SELECT SPECIFICATIONS

www.grayhill.com

Grayhill, Inc.561 Hillgrove AvenueLaGrange, Illinois 60525phone: (708) 354-1040fax: (708) 354-2820

Your Experts in Cab ControlsGrayhill specializes in the design, development and production of human interface controls, including:

- Cab user interface design- Customized control panels- CAN-bus interface devices

specifications subject to change

Operating temperature ANSI/ASAE EP455 5.1.1 Level 2 -30°C to +65°C

Storage Temperature ANSI/ASAE EP455 5.1.2 Level 2 -40°C to +85°C


Altitude (Barometric Pres-sure)

ANSI/ASAE EP455 5.2 101.3kPa to 18.6kPa


Solar Radiation ANSI/ASAE EP455 5.4 43-75W/m2 UV Radiation (280-400nm wavelength) 300h

Ingress Protection / Rain ANSI/ASAE EP455 5.6 Level 2 375 kPa and 8.3 L/min for 10 minutes @15°C water temp



Chemical resistance ISO 16750-5 EP 455 (5.8.2)

Thermal Cycling ISO 16750-4 -40° to 85°C 2 hours at extremes change rate = 1°C/min (8 hours) repeat for 30 cycles.

* Contact Grayhill for Linux version

www.grayhill.comwww.grayhill.com

www.grayhill.com


Rev 06/14

DIMENSIONS

WEIGHT4.7 lbs.


Vibration, Random ANSI/ASEA EP455 5.15.1 2h each axis @52.4m/s2 RMS overall accel-eration and spectral power density of 2m2/s3 from 50Hz to 2000Hz

Vibration, Sinusoidal ANSI/ASEA EP455 5.15.2 A logarithmic sweep from 10Hz to 2000Hz to 10Hz over a period of 20 minutes for 4 hours in each of 3 orthogonal axes with amplitude 1.5mm from 10Hz to 40Hz and a constant acceleration of 35m/s2 RMS from 40Hz to 2KHz

Shock / Crash Safety ANSI/ASEA EP455 5.14 11ms half sine pulse of 490 m/s2 in 3 perpendicular axes

Drop ANSI/ASEA EP455 5.14.2 Level 1



Alternator Field Decay ANSI / ASAE EP455 Sec 5.11.2

ESD ANSI / ASAE EP455 Sec 5.12 Level 2

Radiated Immunity ANSI / ASAE EP455 Sec 5.16 Level 1

Broadband Radiated Emissions

ISO 14982 Sec 6.4

Narrowband Radiated Emissions

ISO 14982 Sec 6.5

Conducted Emissions SAE J1113-41 Class 2

ELECTRICAL PERFORMANCE SPECIFICATIONS (CONTINUED)

Maximum Load ANSI / ASAE EP455 Sec 5.1.1 T(min) = -40C, T(max) = +65C

Over-voltage ANSI / ASAE EP455 Sec 5.10.2 Level 1, extended to 36V

Reverse Polarity ANSI / ASAE EP455 Sec 5.10.3 extended to -36V

Short-circuit Protection ANSI / ASAE EP455 Sec 5.10.4 extended to 36V

Starting Profile ISO 16750-2 Sec. 4.6.3 12V, Code C / 24V Code E

Battery-less Operation ANSI / ASAE EP455 Sec 5.11.3 Level 1

Load Dump ISO 7637-2 Pulse 5b Us = 174V, Ri = 2 Ohms, Td = 350mS, Us* = 70V

Switching Spikes ISO 7637-2 Pulse 3a and 3b Pulse 3a: Us = -200V, Pulse 3b: Us = 200V, 3000 reps

Wire Harness Inductance

ISO 7637-2 Pulse 2a Us = 50V, t1 = 5s, 60 reps

Motor Shutdown Transients

ISO 7637-2 Pulse 2b Us = 20V, t1 = 5s, Ri < .05 Ohms, 60 reps

Wire Harness Inductance Switching

ISO 7637-3 Pulse a and b Pulse a: –80V, Pulse b: 80V, Class A, 6 min.

Inductive Load Switching

ANSI / ASAE EP455 Sec 5.11.4 Level 1

Mutual Coupling (Power)

ANSI / ASAE EP455 Sec 5.11.6.1

Level 2

Mutual Coupling (Signal/ Input)



10.4

[264,1

6]

PANEL MOUNTING DETAILSMAXIMUM TORQUE: 25 IN-LBSNOMINAL PANEL/POCKET DIMENSIONS SHOWN MAY REQUIRE ADJUSTMENTBASED UPON MANUFACTURING TOLERANCES OF CUSTOMER PANEL

FOUR HOLE AMPS MOUNTING DETAILSUSE M6 NUT (1mm PITCH)

MAX TORQUE: 25 IN-LBS

POWER CONSUMPTION11.5 W typical


6.5-inch VGADisplay for Vehicles• Ideal for gauges, diagnostic menus and other ancillary functions• Capable of displaying three simultaneous video feeds• J1939 compliant CAN interfaces• Interface with Grayhill’s 3J Series Vehicle Display Controller• Sealed to IP67• Optional touch screen• 5 soft keys for menu selection• Adjustable backlight on soft keys• Die cast mount or RAM mount compatible• Full color TFT• LED backlight• VGA resolution (640x480)• 16 bit color• Brightness 650 nits (measured)

www.grayhill.com



* Contact Grayhill for Linux version.

Operating temperature ANSI/ASEA EP455 5.1.1 Level 2 -30°C to +65°C

Storage Temperature ANSI/ASEA EP455 5.1.2 Level 2 -40°C to +85°C

Thermal Shock ANSI/ASEA EP455 5.1.3 -40°C to 70°C at a rate of 4°C/min (1 hour at extremes)

Altitude (Barometric Pres-sure)

ANSI/ASEA EP455 5.2 101.3kPa to 18.6kPa

Sand and Dust ANSI/ASEA EP455 5.3 24 hours with 0.88g/m3

Solar Radiation ANSI/ASEA EP455 5.4 43-75W/m2 UV Radiation (280-400nm wavelength) 300h

Ingress Protection / Rain ANSI/ASEA EP455 5.6 Level 2 375 kPa and 8.3 L/min for 10 minutes @15°C water temp

Humidity ANSI/ASEA EP455 5.13 96% humidity at 35°C for 240 hours

Salt Fog ANSI/ASEA EP455 5.9 5% aqueous solution of NaCl @ 35°C and a pH between 6.5 and 7.2 for 48 hours

Chemical resistance ISO 16750-5 EP 455 (5.8.2) See Table 1

Thermal Cycling ISO 16750-4 -40° to 85°C 2 hours at extremes change rate = 1°C/min (8 hours) repeat for 30 cycles.

EMBEDDED COMPUTER • 416 MHz PXA270 processor• 64MB SDRAM• 128MB NAND program, and file system FLASH• Windows CE or Linux Operating System*• Real time clock with 10 year battery backup

INPUT / OUTPUT• 1 USB host port• 3 CAN bus ports• 3 NTSC/PAL video inputs• 3 RS-232 serial ports• 10/100 ethernet port• Input voltage: 9VDC to 32VDC

CONNECTOR• AMP 776164-1 mating connector• AMP 770520-1 or AMP 770854-1 contacts

CERTIFICATE: CE MARK

PART NUMBER | DESCRIPTION3D65XK-1006 6.5 inch VGA Display, Windows CE63D65TK-1006 6.5 inch with touchscreen, WIN CE6



6.5

[165,10]

www.grayhill.com


Rev 06/14

DIMENSIONS


2h each axis @52.4m/s2 RMS overall accel-eration and spectral power density of 2m2/s3 from 50Hz to 2000Hz


A logarithmic sweep from 10Hz to 2000Hz to 10Hz over a period of 20 minutes for 4 hours in each of 3 orthogonal axes with amplitude 1.5mm from 10Hz to 40Hz and a constant acceleration of 35m/s2 RMS from 40Hz to 2KHz

Shock / Crash Safety ANSI/ASAE EP455 5.14

11ms half sine pulse of 490 m/s2 in 3 perpendicular axes




Alternator Field Decay ANSI / ASAE EP455 Sec 5.11.2

ESD ANSI / ASAE EP455 Sec 5.12 Level 2

Radiated Immunity ANSI / ASAE EP455 Sec 5.16 Level 1

Broadband Radiated Emissions

ISO14982 Sec 6.4

Narrowband Radiated Emissions

ISO 14982 Sec 6.5


ELECTRICAL PERFORMANCE SPECIFICATIONS (CONTINUED)

Maximum Load ANSI / ASAE EP455 Sec 5.1.1 T(min) = -40C, T(max) = +65C

Over-voltage ANSI / ASAE EP455 Sec 5.10.2 Level 1, extended to 36V

Reverse Polarity ANSI / ASAE EP455 Sec 5.10.3 extended to -36V

Short-circuit Protection ANSI / ASAE EP455 Sec 5.10.4 extended to 36V

Starting Profile ISO 16750-2 Sec. 4.6.3 12V, Code C / 24V Code E

Battery-less Operation ANSI / ASAE EP455 Sec 5.11.3 Level 1

Load Dump ISO 7637-2 Pulse 5b Us = 174V, Ri = 2 Ohms, Td = 350mS, Us* = 70V

Switching Spikes ISO 7637-2 Pulse 3a and 3b Pulse 3a: Us = -200V, Pulse 3b: Us = 200V, 3000 reps

Wire Harness Induc-tance

ISO 7637-2 Pulse 2a Us = 50V, t1 = 5s, 60 reps

Motor Shutdown Transients

ISO 7637-2 Pulse 2b Us = 20V, t1 = 5s, Ri < .05 Ohms, 60 reps

Wire Harness Induc-tance Switching

ISO 7637-3 Pulse a and b Pulse a: –80V, Pulse b: 80V, Class A, 6 min.

Inductive Load Switch-ing

ANSI / ASAE EP455 Sec 5.11.4 Level 1

Mutual Coupling (Power)


Level 2

Mutual Coupling (Sig-nal/ Input)



WEIGHT2.2 lbs.

POWER CONSUMPTION8.5 W typical



Vehicle Display Controller• Three Configurations - Optical Rotary Encoder - Encoder with Pushbutton - Joysticking Encoder with Pushbutton• J1939 and CANopen versions• Dimmable LED indicators and legends• Sealed to IP67• Vibration and impact resistant• Operating Temp: -40oC to +85oC• Long Life: 500,000 cycles• Support for multiple key combinations• Designed for 12/24 volt systems• Custom legends and configurations

DIMENSIONS in inches (and millimeters)

www.grayhill.com

Put display functions within reach- 5 hot keys for rapid navigation

- Scroll with rotary encoder- Select with pushbutton- Navigate with joystick

Rotary Encoder version with Target Legends

Joysticking Encoder version

Your Experts in Cab ControlsGrayhill specializes in the design, development andproduction of human interface controls, including:

- Cab user interface design - Customized control panels - CAN-bus interface devices

Esc

Blank keys shown below

ISO Symbols shown below Recommended Panel Cut-out

www.grayhill.com

Custom options availableContact Grayhill or your local Grayhill sales representative

for more information.

ENVIRONMENTAL SPECIFICATIONSOperating temperature ANSI/ASAE EP455 5.1.1

Level 2-40°C for 4 hours to +85°C for 11 hours

Storage Temperature ANSI/ASAE EP455 5.1.2 Level 2

-40°C 4 hours to+85°C 4 hours




Solar Radiation ANSI/ASAE EP455 5.4 43 to 75W/m2 UV Radiation (280 to 400nm wavelength) for 300h

Wash Down ANSI/ASAE EP455 5.6 Level 2 375 kPa and 8.3 L/min for 10 minutes @15°C Water temp

Ingress Protection IP67 1 meter submersion for 30 minutes

Humidity ANSI/ASAE EP455 5.13 96% Humidity at 35°C for 240 hours.


Chemical resistance (Resis-tance to Solvents)

ISO 16750-5 EP 455 (5.8.2)

Thermal Cycling (Change of Temperature)

ISO 16750-4 -40° to 85°C 2 hours atextremes change rate = 1°C/min (8 hours) repeat for 30 cycles.

MECHANICAL PERFORMANCEVibration, Random ANSI/ASAE EP455 5.15.1 2 hours each axis @ 52.4 m/s2

RMS overall acceleration and spectral power density of 2m2/s3 from 50Hz to 2000Hz

Vibration, Sinusoidal ANSI/ASAE EP455 5.15.2 A logarithmic sweep from 10Hz to 2000Hz to 10Hz over a period of 20 minutes for 4 hours in each of 3 orthogonal axes with amplitude of 1.5mm from 10Hz to 40Hz and a constant acceleration of 35m/s2 RMS from 40Hz to 2000Hz.

Shock / Crash Safety ANSI/ASAE EP455 5.14 A single 11ms half sine pulse of 490 m/s2 in 3 perpendicular axes.


Drop component 400 mm onto a hardwood benchtop on allpractical edges.

Shipping integrity International Safe Transit Agency procedure 3A

ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONSESD ANSI/ASAE EP455 5.12 +/- 25kV for 10 pulses, 5 of

each polarity

Radiated Immunity ISO14982 6.6 10MHz-1000MHz Range 48mA Bulk Current Injection 100V/m


Broadband Radiated Emissions ISO14982 6.4 64dB to 54dB, 30MHz-75MHz (linearly decreases) 54dB to 65dB, 75MHz-400MHz (linearly increases) 65dB, 400MHz-1000MHz

ELECTRICAL PERFORMANCE SPECIFICATIONSMaximum load ANSI/ASAE EP455 5.1.1

Level 2 -40°C 4 hours +85°C for 11 hours max load applied

Jump start forward voltage ISO 16750-2 36V for 60 minutes

Jump start reverse voltage ISO 16750-2 -36V for 60 minutes

Short circuit protection ISO 16750-2 All outputs to ground for 60s

Reverse polarity protection ISO 16750-2 28V for 60s

Starting profile ISO 16750-2 Class A


Apply 6+12.6sin(2*pi*f*t) f is swept from 500Hz to 1.5kHz 5min

Load dump ISO 7637-2 Test Pulse 5b Class A

Switching spikes – negative ISO 7637-2 Test Pulse 3a Class A

Switching spikes – positive ISO 7637-2 Test Pulse 3b Class A


Class A

+/- inductive load pulse ANSI/ASAE EP455 5.11.4 14-300e^(-t/.001)V 1Hz for 300 cycles

+/- mutual coupling ANSI/ASAE EP455 5.11.6 Level 2

14+200e^(-t/14x10^-6)V 1Hz for 300 cycles

Alternator field decay ANSI/ASAE EP455 5.11.2 Class A

CE COMPLIANCEAgriculture and Forestry Machinery EMC

ISO 14982 ESA

Construction Machinery EMC EN 13309:2000 ESA

Bulletin 1124Rev 06/14

Pin 1 2 3 4Signal Power Gnd CAN_H CAN_L

CONNECTION4 pin Deutsch DT Connector. Power with 8V to 32V vehicle type inputs.

ORDERING INFORMATION

Grayhill, Inc.561 Hillgrove Avenue phone: (708) 354-1040LaGrange, Illinois 60525 fax: (708) 354-2820

3 J X X X 5 - 2 0 0 NSeries Code

Keypad Symbols 0 = Blank 1 = ISO Symbols (as shown in dimensional drawing) 2 = Targets

Input Type 0 = Encoder 1 = Joystick Encoder

Protocol Blank = J1939 N = CANopen

Custom Designation 200 = Default

Center Pushbutton 0 = No pushbutton 1 = Pushbutton (joystick always has pushbutton)

Configuration 5 = Default


www.grayhill.com

CAN-bus Keypads for Off-Highway Vehicles ANSI/ASAE EP455 5.12 +/- 25kV for 10 pulses, 5 of each...

Documents

Transcript of CAN-bus Keypads for Off-Highway Vehicles ANSI/ASAE EP455 5.12 +/- 25kV for 10 pulses, 5 of each...