CABLES FOR ALARM AND SAFETY SYSTEMS and safety systems 2018... · 2018-02-28 · Burglar alarms...

CABLES FOR ALARM AND SAFETY SYSTEMS

3

IT´S ALL ABOUT RELIABILITY.It is always important to choose high quality cables,

especially when it comes to alarms and safety systems.

Even small and seemingly insignificant details can make

a big difference in terms of ease of handling,

functionality and service life.

We have the cables you are looking for

We offer the widest range of cables on the market for every

kind of installation. The cables we supply carry signals and

power supplies. For extra peace of mind concerning fire

protection, our cables are available in versions meeting

specified fire safety requirements in installations.

Halogen free for greater safety

We have decided only to include halogen free cables in this

brochure. There is a clear trend in that direction, and there is

no longer any reason for not choosing halogen free cables.

Halogen free cables offer many advantages – in particular,

they make it easier to escape the building in the event of fire,

generating substantial savings in the long run.

100 years of experience thrown in

At Nexans we research, develop and manufacture cables for

the whole world. For different environments and climates. And

we’ve been doing it for more than a hundred years. So when

you choose our cables, they come with a whole lot more – our

dedication and all the experience and expertise we’ve built up

over the decades.

4

PRODUCT SEGMENTS

FIRE ALARMS Detector networks often occupy

large volumes so cables must be

easy to install. Nexans cables are

easy to strip and are optimised

to simplify installation in pipes.

Choose from simple, non twisted

pair cables for small conventional

systems and twisted pair cables for

larger addressable systems. The

cables used in fire alarm detector

networks should normally have a

red sheath. If the cables are

required to keep working during

a fire, you should use Nexans

Alsecure® (see page 12

”Performance during a fire”).

VIDEO SURVEILLANCE (CCTV) Locally installed CCTV (closed circuit

TV) systems are increasingly being

used as a crime prevention tool.

4

5

ACCESS PROTECTION Burglar alarms usually have a

system of control units and sensors.

Indoor and outdoor entry systems

contain card readers, central units

and computers. The cables used for

intruder protection and entry control

are signal cables with

varying flexibility, shielding and

cores. Alternatively, combination

cables can be used with separate

cores carrying the power supply.

Nexans’ wide range makes it easy

to choose the right cables for the

various components.

PERFORMANCE DURING A FIREThere is a separate fire class for

cables that are required to maintain

sircuit integrity during a fire. These

cables all have unique insulation

material that is not damaged like

normal cables. This category can

include power supply cables as well

as signal cables. They should also

be flame retardant low fire hazard

cables – in other words they must

not give off any toxic or corrosive

gases, and only small amounts of

smoke, if there is a fire.

The Nexans cables for these

applications are called Alsecure®.

The unique insulation (INFIT™)

makes the cables easy to install

while ensuring they still work during

a fire.

5

6

CCTV (Closed Circuit TeleVision) is a locally installed video

surveillance system. A CCTV system consists of cameras,

monitors, transmission elements (cables), control systems and

storage systems. Our range of halogen free cables for CCTV

includes 75 ohm coaxial cable.

The S/FTP Category 6A cable together with the

IP67 outlet box offers a safe and robust solution for

solutions for IP network cameras outdoor and in harsh

environments.

RG 59 LSZHCoaxial cable for video surveillance. The impedance of the

cable: 75 ohm.

Cable STK no. Outer diam. Length

RG 59 LSZH 0235704 6,1 mm Bobbin/100

RG 59 LSZH 0235708 6,1 mm Bobbin/500

VIDEO SURVEILLANCE (CCTV)

7

LANmark Industry outlet IP67The LANmark Industry outlet enables the installation of data

outlets in exposed areas as well as outdoor solutions. The IP67

level of protection is maintained both when the outlet is unused

and when the appropriate IP67 patchcords are connected.

Includes 2 screened category 6 or category 6A connectors.

Cable STK no.

IP67 outer with RJ45 cat.6 shielded Snap-in connector, black. 7280048

S/FTP Category 6A LSZH + PECategory 6A, 500 MHz Screened data cable. The 4 pairs are

individually foiled and covered with a common braid. Due to

the outer sheath of PE the cable is appropriate for outdoor

installation as well as in exposed areas. It can be installed

indoors when the PE sheet is removed. The cable fulfills cat 6A

performance according to EN 50288, IEC 61156

and TIA 568-B


Category 6A 4x2x0,5 0233347 8,6 mm B/500

9

YOU OFTEN WON’T KNOW WHETHER YOU CHOSE THE RIGHT CABLE UNTIL AFTER A FIRE.

People always talk about fire protection but it is important to know what this actually

means in practical terms, and to be certain which flame spread rating you need to use.

For cables, you also need to distinguish between flame spread, fire hazard properties and

fire resistance.

Cables that prevent flame spread

Cables running through building levels and walls are a great way for fires to spread. So

the most important requirement when establishing fire protection is to use cables with

properties that prevent the spread of fire. This is why there are general flame spread

classes, and these must always be defined. Our cables have clearly marked flame spread

classes that are informative and easy to understand.

Halogen free – saving lives and money

Smoke and gases from burning cables often cause the biggest problems for people and

equipment. These problems can be reduced if halogen free cables are used. The smoke

from halogen free cables during a fire is much thinner and does not corrode metals.

This makes it easier to clear smoke from rooms, potentially saving lives. That is why our

cables for alarms and safety systems are halogen free.

Still working during a fire

The most critical cables must also be fire resistant. This means they must be guaranteed

to work even during a fire. This is made possible by special insulation material, which is

merely altered rather than destroyed by fire. The cable keeps its shape, the conductors

are kept separate and the cable continues to work. These cables are needed for the fire

alarm system itself, but also for the safety lighting guiding people out of the building, for

the smoke extraction fans and for the lifts. Our range includes fire resistant cables for

power supply and for communication.

10

Nexans has a full range of cables for fire alarm systems

The right cable for the right use

Cables for fire alarms are available with either red or grey

sheaths depending on the regulations, aesthetic requirements,

etc. In larger addressable systems, twisted pair cable should

be used, KLM-LSZH 2x1.0 mm. If shielded cable is required,

Nexans supplies the KLMA LSZH. If the cables are required to

keep working during a fire, fire resistant Alsecure cables are

used.

Installation

The cables for fire alarms are intended for permanent indoor

installation.

KLM Easy™ LSZH 2x1,0Halogen free, pair-twisted signal cable. The cable construction

is as specified in SS 424 16 54 (EQQYB).


KLM Easy™ LSZH 2x1,0 0233358 5,7 mm Bobbin/500

KLM Easy™ LSZH 2x1,0 0235713 5,7 mm Bobbin/100

FIRE ALARMS

KLMA LSZH Halogen free, pair-twisted signal cable. The cable construction

is as specified in SFS 2751.


KLMA LSZH 2x0,8 0233370 5,0 mm Coil/150

KLMA LSZH 2x0,8 0233369 5,0 mm Bobbin/600

KLMA LSZH 4x0,8 0233378 5,5 mm Coil/150

KLMA LSZH 4x0,8 0233374 5,5 mm Bobbin/600

KLM LSZH Halogen free signal cable. The cable construction is, where

applicable, as specified in SFS 2751.


KLM LSZH 2x0,8 0233362 4,0 mm Coil/150

KLM LSZH 2x0,8 0233360 4,0 mm Bobbin/600

KLM LSZH 4x0,8 0233368 5,0 mm Coil/150

KLM LSZH 4x0,8 0233364 5,0 mm Bobbin/600

12

Fire resistant cables are recommended for use in installations

that must maintain circuit integrity during a fire. Using these

cables in important alarm, control, signal and power supply

systems means you can guarantee they will not be taken down,

even if the fire reaches the cables themselves.

No gases, little smoke

As well as continuing to work during and after a fire, Nexans fire

resistant cables are halogen free so they do not release any toxic

or corrosive gases, and only small amounts of smoke, if there is

a fire. Studies show that this can save lives and money.

Installation

Examples of systems that must maintain circuit integrity during a

fire include signal and safety systems guiding people out of the

building. Other examples are smoke extraction fans and lifts.

Fire alarm cables, too, if they pass through areas that are not

monitored by detectors, are required to maintain circuit integrity

during a fire.

ALSECURE® PREMIUMFire resistant, twisted pair, fire alarm cables for permanent

installation indoors or in pipes. Fire performance according to

IEC60331, IEC 60332-3.


Alsecure Premium 2 x 1,0 mm 0235747 6,2 mm Bobbin/500

Alsecure Premium 10 x 2 x 1,0 mm 0235748 17,0 mm Drum/500

ALSECURE® PLUS 0,6/1kV, FRHFFire resistant power cable with round or sector shaped,

stranded, soldered copper conductor and concentric shielding.

For permanent installation in all areas. Fire performance

according to IEC 60331, IEC 60332-3.


Alsecure Plus 1 kV 2 x 1,5/1,5 0638502 11,9 mm Drum/500






Alsecure Plus 1 kV 4 x 6/6 0638510 18,1 mm Drum/500












PERFORMANCE DURING A FIRE

13

ALSECURE® PREMIUM 300/500VFire resistant, halogen free control cables with round, solid

copper conductors. This cable is designed for permanent

installation on cable ladders, directly on walls or in pipes or

ducting. Applications include emergency lighting, fire alarm

systems and control systems. Fire performance according to

IEC60331, IEC 60332-3.


Alsecure Premium 3G1,5 0603470 8,0 mm Drum/500





14

ACCESS PROTECTIONOur cables for intruder alarms and entry systems come in a

range of types. We have shielded as well as unshielded twisted

pair cables – up to hundred pairs. We also offer flexible single

wire cables with 4 to 12 cores. Combination cables are also

available for entry systems – cables with twisted pair signal

elements and power supply elements (max 100 V).

Fire performance according to CPR cluss Dca-s2,d2,a2.

MHS LSZHPair-twisted, shielded communication cable with halogen free,

flame retardant sheath. The cable construction is, where

applicable, as specified in SFS 5739.


MHS LSZH 1x4x0,5 0233380 5,0 Coil/100

MHS LSZH 1x4x0,5 0233379 5,0 Drum/1000

MHS LSZH 3x2x0,5 0233382 6,0 Coil/200

MHS LSZH 3x2x0,5 0233381 6,0 Drum/1000

MHS LSZH 5x2x0,5 0233384 6,5 Coil/150

MHS LSZH 5x2x0,5 0233383 6,5 Drum/1000

MHS LSZH 10x2x0,5 0233386 8,5 Coil/100

MHS LSZH 10x2x0,5 0233385 8,5 Drum/1000

EQQXB Easy TM (halogen free EKKX)Pair-twisted communication cable with halogen free, flame

retardant insulation and sheath. An important feature of the cable

is that both insulation and sheath are easy to peel. You can even

peel the insulation with your nail.

Cable Nexans no. Outer diam. Length

EQQXB Easy TM 1 x 4 x 0,5 mm 17112041 3,5 mm Bobbin/100














FQQXBFlexible signal and alarm cables for intruder alarms and access

control systems.


FQQXB 4 x 0,22 mm2 17527141 3,7 mm Bobbin/100








15

FLAQQBRCombined power supply and signal cables for intruder alarms

and entry systems. The twisted pair signal element is unshielded.


FLAQQBR 2 x 1,0 + 1 x 2 x 0,22 mm2 17037141 6,5 mm Bobbin/100

FLAQQBR 2 x 1,0 + 1 x 2 x 0,22 mm2 17037171 6,5 mm Bobbin/500

FLAQQBR 2 x 1,0 + 2 x 2 x 0,22 mm2 17037298 8,0 mm Drum/500

FLAQQBR 4 x 1,0 + 2 x 2 x 0,22 mm2 17037698 8,7 mm Drum/500

FLQQBRCombined power supply and signal cables for intruder alarms

and entry systems. The twisted pair signal element is unshielded.


FLQQBR 2 x 1,5 + 2 x 2 x 0,5 mm2 17030698 8,5 mm Drum/500

FLQQBR 2 x 1,0 + 1 x 2 x 0,22 mm2 17030141 6,5 mm Bobbin/100



FLAQQLYCombined power supply and signal cable for intruder alarms

and entry systems. The pairs for signalling have a common

screen of aluminium/polyesterfoil.

The cable has a protective PE sheath covering the inner sheat of

halogen free flame retardant plastic compound and is intended

for fixed installations both indoor and outdoor.

Cabel Nexans no. Outer diam. Length

FLAQQLY 2 x 1,0 + 2 x 2 x 0,22 mm2 17039298 9,0 mm Drum/500

16

NEXANS SWEDEN ABKABELGATAN 1514 81 GRIMSÅS0325-800 00www.nexans.se@nexanssweden

CAB

LES

FOR

ALAR

M-

AND

SAF

ETY

SYST

EMS

2018

CABLES FOR ALARM AND SAFETY SYSTEMS and safety systems 2018... · 2018-02-28 · Burglar alarms...

Documents

Transcript of CABLES FOR ALARM AND SAFETY SYSTEMS and safety systems 2018... · 2018-02-28 · Burglar alarms...