Cable Laying Equipment - Cable Pulling Grips & Cable Pulling Socks
1
Cable grips (also often referred to as cable stockings, pulling socks or ‘Chinese fingers’) are a quick and efficient way to install/control electrical cables. Cable grips are re-usable (subject to inspection) and can also be used to support or pull any cylindrical object within their grip and load carrying capacity. TWS part no. Cable diameter Lattice weave Lattice length Overall length Approx breaking strength (SE)10-13* 10-13mm Single 230mm 305mm 760kg (SE)13-19* 13-19mm Single 355mm 430mm 1,015kg (SE)19-25* 19-25mm Single 405mm 510mm 2,540kg (SE)25-38* 25-38mm Single 455mm 610mm 3,555kg (SE)38-50* 38-50mm Double 535mm 735mm 5,080kg (SE)50-63* 50-63mm Double 610mm 865mm 5,080kg (SE)63-89* 63-89mm Double 685mm 990mm 6,095kg (SE)89-115* 89-115mm Double 685mm 990mm 7,110mm *Above are single eye part numbers, for alternative styles, substitute the pre-fix (SE) with the pre-fix from the styles listed below. Single Eye (SE) – Ideal for pulling medium to heavy loads, the pull can only be achieved from the cable end. Fleeting Eye (FE) – Similar to the SE type but for use when offset positioning is required and the cable can pass completely through the cable grip. Double Eye (DE) – Suitable for pulling medium to heavy loads, the main advantage to the SE Type is that the cable can be passed through the grip thus enabling the pull to be made at various stages down the cable. Lace Up (LU) – Similar to the DE type but the grip is positioned on the cable and then stitched together. This is particularly useful when the pull is from someway down the cable or when there is a connector on the cable end. Open Ended (OE) – Ideal for joining 2 cables and mainly used when old cable is being replaced with new (see our website for specifications). Non-Conductive (NC) – Ideal for use in water, fibre optic applications, offshore or for a multitude of uses in the electrical industry; dramatically improved weight to break ratio and made of a high-strength, non-conductive aramid fibre (see our website for specifications). For more information 16 Cable pulling grips Single eye Double eye Lace up Open ended Non-conductive
-
Upload
reid-brothers-uk -
Category
Technology
-
view
135 -
download
0
description
http://reidbrothers.co.uk/product-details/cable-grips-cable-socks Tele: 0141 425 1060 Email: [email protected] Cable Pulling Grips and Cable Socks Reid Brothers UK are suppliers of a vast range of cable pulling grips, also known as cable stockings, pulling socks and sometimes known as Chinese fingers. These cable pulling grips are ideal for safely controlling the installation of electrical cables. The cable pulling grips available range from single eye cable grips to non-conductive cable grips. The cable pulling grips are re-usable (subject to inspection.) The range of cable pulling grips can also be used to pull any cylindrical object as long as its within the cable pulling grips size and load capacity. The full range of cable pulling grips available from Reid Brothers UK are: Single Eye Cable Pulling Grip (SE). The single eye cable pulling grip is ideal for pulling medium to heavy loads. The pull can only be achieved from the cable end. Fleeting Eye Cable Pulling Grip (FE). The fleeting eye cable pulling grip is similar to the above SE cable grip but is best suited to use when offset positioning is required and the cable can be completely passed through the cable pulling grip. Double Eye Cable Pulling Grip (DE). The double eye cable grip is ideal for use on medium to heavy loads, with the main advantage of the DE grip is the cable can be passed through the cable pulling grip. This allows pull to be made at various points along the cable. Lace-Up Cable Pulling Grip (LU). The lace up cable pulling grip is similar to the above DE type grip. The main difference between the two being the LU grip is positioned on the cable then stitched together. This grip is useful when the pull is someway down the cable or if there is a connector on the cable end. Open Ended Cable Pulling Grip (OE).The open ended cable pulling grip is ideal for joining two cables. This is mainly used when old cable is being replaced with new cable. Non-Conductive Cable Pulling Grip (NC). The non conductive cable pulling grip does exactly what it is described as: a non conductive cable grip. This makes it ideal for use in water, fibre optic applications and off shore as well as many other applications in the electric industry. The NC cable gripper has an improved weight to break ratio and is made form high tensile non-conductive aramid fibre.
Transcript of Cable Laying Equipment - Cable Pulling Grips & Cable Pulling Socks
Cable grips (also often referred to as cable stockings, pulling socks or ‘Chinese fingers’) are a quick and efficient way to install/control electrical cables. Cable grips are re-usable (subject to inspection) and can also be used to support or pull any cylindrical object within their grip and load carrying capacity.
TWS part no. Cable diameter Lattice weave Lattice length Overall length Approx breaking strength
(SE)10-13* 10-13mm Single 230mm 305mm 760kg(SE)13-19* 13-19mm Single 355mm 430mm 1,015kg(SE)19-25* 19-25mm Single 405mm 510mm 2,540kg(SE)25-38* 25-38mm Single 455mm 610mm 3,555kg(SE)38-50* 38-50mm Double 535mm 735mm 5,080kg(SE)50-63* 50-63mm Double 610mm 865mm 5,080kg(SE)63-89* 63-89mm Double 685mm 990mm 6,095kg
(SE)89-115* 89-115mm Double 685mm 990mm 7,110mm
*Above are single eye part numbers, for alternative styles, substitute the pre-fix (SE) with the pre-fix from the styles listed below.
Single Eye (SE) – Ideal for pulling medium to heavy loads, the pull can only be achieved from the cable end.
Fleeting Eye (FE) – Similar to the SE type but for use when offset positioning is required and the cable can pass completely through the cable grip.
Double Eye (DE) – Suitable for pulling medium to heavy loads, the main advantage to the SE Type is that the cable can be passed through the grip thus enabling the pull to be made at various stages down the cable.
Lace Up (LU) – Similar to the DE type but the grip is positioned on the cable and then stitched together. This is particularly useful when the pull is from someway down the cable or when there is a connector on the cable end.
Open Ended (OE) – Ideal for joining 2 cables and mainly used when old cable is being replaced with new (see our website for specifications).
Non-Conductive (NC) – Ideal for use in water, fibre optic applications, offshore or for a multitude of uses in the electrical industry; dramatically improved weight to break ratio and made of a high-strength, non-conductive aramid fibre (see our website for specifications).
For more information
16 Cable pulling grips
Single eye Double eye Lace up Open ended Non-conductive
Thomas
Logo
