CableMasterCM400

Quick Start Guide

Testing:A. Plug the wire into the correct Test Port, Ethernet to RJ45B. Plug the opposite end into the Main RemoteC. Press Network ButtonD. The LCD Display reports wire condition, Pass/FailE. To turn off, press O/ID Button

Toning:A. With the unit turned OFF, hold down the TONE button until LCD illuminatesB. To select a tone cadence, press the TONE button repeatedly to step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the option you want. The option you select determines the cadence sent from the main tester, through the cable, and picked up by the tone tracer probe.C. Press the appropriate cable type button (voice, video, or data) to select a cable for the tone signal* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS andFAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packedtone generator. Its confi gurable signal can be generated to fi nd and fi x theposition on any type of cable - either exposed or hidden, in ceilings orbehind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

Button Function1. LCD Display2. Voice Mode3. Video Mode4. Data Mode

1

4

3

6

7

5

2

5. Tone Mode6. On/Off and ID Mode7. Main Unit Remote

(RJ11, RJ45)

CableMaster CM400

Quick Start GuideKurzanleitung

Guide de Démarrage Rapide

CableMasterCM400

Quick Start Guide

Testing:A. Plug the wire into the correct Test Port, Ethernet to RJ45B. Plug the opposite end into the Main RemoteC. Press Network ButtonD. The LCD Display reports wire condition, Pass/FailE. To turn off, press O/ID Button

Toning:A. With the unit turned OFF, hold down the TONE button until LCD illuminatesB. To select a tone cadence, press the TONE button repeatedly to step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the option you want. The option you select determines the cadence sent from the main tester, through the cable, and picked up by the tone tracer probe.C. Press the appropriate cable type button (voice, video, or data) to select a cable for the tone signal* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS andFAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packedtone generator. Its confi gurable signal can be generated to fi nd and fi x theposition on any type of cable - either exposed or hidden, in ceilings orbehind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

Button Function1. LCD Display2. Voice Mode3. Video Mode4. Data Mode

1

4

3

6

7

5

2

5. Tone Mode6. On/Off and ID Mode7. Main Unit Remote

(RJ11, RJ45)

CableMaster CM400

Quick Start Guide

Button Function1 LCD Display 5 Tone Mode2 Voice Mode 6 On/Off and ID Mode3 Video Mode 7 Main Unit Remote4 Data Mode (RJ11/RJ12, RJ45)

English

A. Plug the wire into the correct Test Port, e.g. Ethernet to RJ45B. Plug the opposite end into the Main RemoteC. Press Network ButtonD. The LCD Display reports wire condition, Pass/FailE. To turn off, press O/ID Button

Toning:A. With the unit turned OFF, hold down the LENGTH/TONE button until LCD

illuminatesB. To select a tone cadence, press the LENGTH/TONE button repeatedly to

step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo 2. Stop when you reach the option you want. The option you select determines the cadence sent from the main tester, through the cable, and picked up by the tone tracer probe*.

C. Press the appropriate cable type button (voice, video or data) to select a cable for the tone signal

* Note: Tone is detected by a tone tracer probe (optional)

Features:Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS andFAIL results quickly.Toning: CM400`s built- in tone generator is a flexible and function- packed Tone generator. Its configurable signal can be generated to find and fix the position on any type of cable – either exposed or hidden, in ceilings or behind walls.

Length: CM400 determines the length (in feet or meters) of an entire cable and/ or individual wire pairs within the cable.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax) and (1-8) testing/ID remotes (Network/Telephone).

English

CableMasterCM400

Quick Start Guide

Testing:A. Plug the wire into the correct Test Port, Ethernet to RJ45B. Plug the opposite end into the Main RemoteC. Press Network ButtonD. The LCD Display reports wire condition, Pass/FailE. To turn off, press O/ID Button

Toning:A. With the unit turned OFF, hold down the TONE button until LCD illuminatesB. To select a tone cadence, press the TONE button repeatedly to step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the option you want. The option you select determines the cadence sent from the main tester, through the cable, and picked up by the tone tracer probe.C. Press the appropriate cable type button (voice, video, or data) to select a cable for the tone signal* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS andFAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packedtone generator. Its confi gurable signal can be generated to fi nd and fi x theposition on any type of cable - either exposed or hidden, in ceilings orbehind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

Button Function1. LCD Display2. Voice Mode3. Video Mode4. Data Mode

1

4

3

6

7

5

2

5. Tone Mode6. On/Off and ID Mode7. Main Unit Remote

(RJ11, RJ45)

CableMaster CM400

Kurzanleitung

Funktionstasten

1. LCD Display2. Sprachmodus3. Videomodus4. Datenmodus

Deutsch

5. Tonmodus6. Ein/Aus und ID-Modus7. Remoteeinheit

(RJ11/RJ12, RJ45)

5. Tonmodus6. Ein/Aus und ID-Modus7. Remoteeinheit

(RJ11/RJ12, RJ45)

A. Schließen Sie ein Kabelende an die RJ45 Buchse am Hauptgerät an. B. Schließen Sie das andere Ende an die RJ45 Buchse der Remoteeinheit an.C. Drücken Sie die Taste Netzwerk.D. Auf dem Bildschirm wird das Ergebnis mit Pass/Fail und der Verdrahtungs-

plan angezeigt E. Zum Ausschalten des Gerätes drücken Sie die Taste O/ID

Tonverfolgung:A. Bei ABGESCHALTETEM Gerät halten Sie die Taste TON solange gedrückt,

bis der Bildschirm aufleuchtetB. Zum Auswählen eines von vier möglichen Tonmustern drücken Sie die

Taste TON wiederholt, bis das gewünschte Tonmuster angezeigt wird (HI, LO, Hi-Lo1 und Hi-Lo2). Vom Hauptgerät wird das gewählte Tonsignal auf das Kabel gesendet und kann nun mit dem Tonverfolger geortet werden

C. Drücken Sie die entsprechende Taste für den Kabeltyp (Voice - Sprache, Video oder Data - Daten), der mit diesem Tonsignal beaufschlagt werden soll.

* Hinweis: Der Ton wird mit einem Tonverfolger geortet (optionales Zubehör).

Funktionsmerkmale:Test: Im Handumdrehen zeigt der CM400 Unterbrechungen, Kurzschlüsse, Verdrahtungsfehler, Split Pair-Fehler, PASS und FAIL Ergebnisse auf dem Bildschirm an.Tonverfolgung: Der integrierte Tongenerator des CM400 kann flexibel auf die Erzeugung von vier verschiedenen Tonmustern konfiguriert werden. Über das Tonsignal ist es möglich, jedes Kabel zu orten und dessen Verlauf zu verfol-gen – ob freiliegend oder unter Putz, in der Decke oder hinter der Wand.

Option: Zur Verwendung mit dem CM400 können (1 – 19) Fernerkennungen (Netzwerk/Koaxial) zur Kabelerkennung und (1 – 8) Fernerkennungen (Netz-werk/Telefon) zum Test/ID separat bestellt werden.

Deutsch

CableMasterCM400

Quick Start Guide

Testing:A. Plug the wire into the correct Test Port, Ethernet to RJ45B. Plug the opposite end into the Main RemoteC. Press Network ButtonD. The LCD Display reports wire condition, Pass/FailE. To turn off, press O/ID Button

Toning:A. With the unit turned OFF, hold down the TONE button until LCD illuminatesB. To select a tone cadence, press the TONE button repeatedly to step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the option you want. The option you select determines the cadence sent from the main tester, through the cable, and picked up by the tone tracer probe.C. Press the appropriate cable type button (voice, video, or data) to select a cable for the tone signal* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS andFAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packedtone generator. Its confi gurable signal can be generated to fi nd and fi x theposition on any type of cable - either exposed or hidden, in ceilings orbehind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

Button Function1. LCD Display2. Voice Mode3. Video Mode4. Data Mode

1

4

3

6

7

5

2

5. Tone Mode6. On/Off and ID Mode7. Main Unit Remote

(RJ11, RJ45)

CableMaster CM400

Guide de Démarrage Rapide

Touches

1. Ecran LCD2. Mode Voix3. Mode Vidéo4. Mode Données

France

5. Mode Tonalité6. Marche/Arrêt et Mode ID7. Unité Distante

(RJ11/ RJ12, RJ45)

5. Mode Tonalité6. Marche/Arrêt et Mode ID7. Unité Distante

(RJ11/ RJ12, RJ45)

A. Branchez une extrémité du câble sur le port RJ45 du testeur principal.B. Branchez l’autre extrémité du câble sur l’unité distante.C. Pressez la touche Network (Réseau).D. L’écran affichera le résultat : Pass/Fail (Succès/Echec), schéma de câblageE. Pour éteindre le testeur, pressez la touche O/ID.

Tonalité :A. Le testeur éteint, tenez la touche TONE (Tonalité) enfoncée, jusqu’à l’écran

s’allume.B. Pour sélectionner la tonalité, pressez la touche TONE plusieur fois et faites

votre choix entre quatre tonalités : HI, LO, Hi-Lo1 et Hi-Lo2. Arrêtez, quand l’option désirée s’affiche. Le testeur émettra la tonalité choisie sur le câble pour le dépister avec le dépisteur de tonalité.

C. Pressez la touche appropriée au type de câble (voice - voix, video - vidéo, ou data - données) pour transmettre la tonalité.

* Note : La tonalité sera détectée par un dépisteur de tonalité.((Accessoires optionnels)

Caractéristiques :Test : CM400 affiche rapidement les résultats de test: courts-circuits, circuits ouverts, mauvais câblage, paires séparées (Split Pairs), Pass/Fail (Succès/Echec).

Tonalité : Le générateur de tonalité incorporé dans le CM400 peut fl exible-ment être confi gurré à la tonalité désirée pour trouver la position d’un prob-lème sur chaque type de câble - si exposé ou encastré dans des plafonds ou des murs.

Option : Le CM400 est soutenu par des (1-19) sondes à distance pour localiser les câbles par l’identification (lID) de câbles (Réseau/Coaxial) et par des (1-8) sondes à distance pour test/ID (Réseau/Téléphone).

France

www.psiberdata.com

For technical information and support please contact the Psiber Office in your country.

Psiber US:Psiber Data Sytems Inc.

7075-K Mission Gorge RoadSan Diego, CA 92120

Phone: +1 (619) 287 99970e-mail: info@psiber.com

www.psiber.com

Psiber Europe:Psiber Data GmbHFelix-Wankel-Str. 4

82152 KraillingGermany

Phone: +49 (89) 8913 6060e-mail: info@psiber-data.com

www.psiberdata.com

Psiber Data Pte. Ltd.:3 Science Park Drive#03-09 The Franklin

Singapore Science Park 1,Singapore 118223

Phone: +65-6569-6019e-mail: asiasales@psiber-data.com

www.psiberdata.com