CABINETMAKER WOODWORKING SYSTEM - … SMART... · Attach the Smart Square When using the EZ SMART...
4
Attach the Smart Square When using the EZ SMART Cabinetmaker Woodworking System with any power tool, be sure you have read and understand the operating manual for the tool before operation. Be sure to use the tool safely. Do not disable any built-in safety features. Be sure to follow safe practices when using the Cabinetmaker with your power tools. If a task seems like it might be potentially unsafe, do not attempt. Do not operate any tool on the Cabinetmaker if you are tired or distracted in any way. Step 1 CABINETMAKER WOODWORKING SYSTEM The EZ SMART Cabinetmaker Woodworking System is useful for making repeatable cross-cuts used in the making of parts for cabinets. It is comprised of the EZ SMART Smart Square with handle and the EZ SMART Repeater that are used with a section of EZ SMART Guide Rail (sold separately). The Smart Square is not only used to square the Guide Rail to the workpiece for 90 degree cuts but is adjustable to allow for angled cuts greater than 90 degrees or less than 90 degrees. The Repeater is extendable to the right or to the left to handle any size workpiece. The Cabinetmaker can also be combined with a second Repeater (sold separately) for added versatility. Smart Square with Handle Repeater The Smart Square is attached along the non-cutting side of the Guide Rail. It is best to attach the Smart Square about 4-12” from the end of the Guide Rail. This allows space for the Repeater to be installed and space for the saw to rest before starting a cut. A speed square can be used to set the desired angle. Once the angle is set, the knobs may be tightened. Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470 Phone (352) 620-2262 Fax (352) 620-2576 [email protected] www.eurekazone.com v14-01 Page 1
Transcript of CABINETMAKER WOODWORKING SYSTEM - … SMART... · Attach the Smart Square When using the EZ SMART...
Attach the Smart Square
When using the EZ SMART Cabinetmaker Woodworking System with any power tool, be sure you have read and understand the operating manual for the tool before operation. Be sure to use the tool safely. Do not disable any built-in safety features. Be sure to follow safe practices when using the Cabinetmaker with your power tools. If a task seems like it might be potentially unsafe, do not attempt. Do not operate any tool on the Cabinetmaker if you are tired or distracted in any way.
Step 1
CABINETMAKER WOODWORKING SYSTEM
The EZ SMART Cabinetmaker Woodworking System is useful for making repeatable cross-cuts used in the making of parts for cabinets. It is comprised of the EZ SMART Smart Square with handle and the EZ SMART Repeater that are used with a section of EZ SMART Guide Rail (sold separately). The Smart Square is not only used to square the Guide Rail to the workpiece for 90 degree cuts but is adjustable to allow for angled cuts greater than 90 degrees or less than 90 degrees. The Repeater is extendable to the right or to the left to handle any size workpiece. The Cabinetmaker can also be combined with a second Repeater (sold separately) for added versatility.
Smart Square with Handle
Repeater
The Smart Square is attached along the non-cutting side of the Guide Rail.
It is best to attach the Smart Square about 4-12” from the end of the Guide Rail. This allows space for the Repeater to be installed and space for the saw to rest before starting a cut.
A speed square can be used to set the desired angle. Once the angle is set, the knobs may be tightened.
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 [email protected] www.eurekazone.com v14-01Page 1
At tach the Handl eSt ep 2
The handle is attached facing toward the workpiece. Place it a comfortable location on the Smart Square.
The handle base overlaps the workpiece and serves to keep the entire unit (Smart Square and Guide Rail) flat to the workpiece.
Set t i ng Angl esSt ep 3
A speed square can be used to set the Smart Square at various angles.
The diagram at the left shows a setup for a 45 degree cut.
The slot in Smart Square allows for this versatility.
At tachi ng t he Repeat erSt ep 4
Attach the Repeater as shown
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 [email protected] www.eurekazone.com v14-01Page 2
Setup for 90 Degree Cut Setup for 45 Degree Cut
Setup for Left-Side Keeper Maximum Left-Side Capacity (47”)
Maximum Right-Side Capacity (40”) Additional Repeater
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 [email protected] www.eurekazone.com v14-01Page 3
Two Repeaters without Square Setup for Ripping
Dual Setup #1 Dual Setup #2
2nd Repeater recommended
● Capacity (width): 40” (right side) and 47” (left side including Guide Rail)● Capacity (length): limited only by length of Guide Rails ● The use of the Square is optional when using two repeaters but should always be used when
using a single repeater● The use of the optional additional Repeater is recommended for cuts longer than 48”● Once the Repeaters are set to a particular dimension, no further measuring is needed to make
multiple workpieces of the same size.● Using a dual setup as shown above allows for two different sized workpieces to be cross-cut
without having to make any adjustments to the Repeaters once they are set to the desired dimensions.
Notes
Eurekazone, LLC 1904 NE Jacksonville Rd Ocala, FL 34470Phone (352) 620-2262 Fax (352) 620-2576 [email protected] www.eurekazone.com
Page 4 v14-01
