C200 Two-Way Loudspeaker User's Manual · same high-resolution audio no matter ... MA AND...

C200 TWO-WAYLOUDSPEAKERUSER’S MANUAL

C200

2

SAFETY INSTRUCTIONS

Duration Per Day Sound Level dBA, Typical In Hours Slow Response Example

8 90 Duo in small club6 924 95 Subway Train3 972 100 Very loud classical music

1.5 1021 105 Tami screaming at Adrian about deadlines

0.5 110 0.25 or less 115 Loudest parts at a rock concert

9. Servicing — The user should not attempt to service this Mackieproduct beyond those means described in this operating manual. All otherservicing should be referred to the Mackie Service Department.

10. Exposure to extremely high noiselevels may cause permanent hearing loss.Individuals vary considerably in susceptibil-ity to noise-induced hearing loss, butnearly everyone will lose some hearing ifexposed to sufficiently intense noise for a

period of time. The U.S. Government’s Occupational Safety and HealthAdministration (OSHA) has specified the permissible noise levelexposures shown in the following chart.

According to OSHA, any exposure in excess of these permissible limitscould result in some hearing loss. To ensure against potentially dangerous ex-posure to high sound pressure levels, it is recommended that all personsexposed to equipment capable of producing high sound pressure levels usehearing protectors while the equipment is in operation. Ear plugs or protectors inthe ear canals or over the ears must be worn when operating the equipment inorder to prevent a permanent hearing loss if exposure is in excess of the limitsset forth here.

1. Read Instructions — All the safety and operation instructions shouldbe read before this Mackie product is operated.

2. Retain Instructions — The safety and operating instructions should bekept for future reference.

3. Heed Warnings — All warnings on this Mackie product and in theseoperating instructions should be followed.

4. Follow Instructions — All operating and other instructions should befollowed.

5. Water and Moisture — This Mackie product should not be used nearwater – for example, near a bathtub, washbowl, kitchen sink, laundrytub, in a wet basement, near a swimming pool, swamp or salivating St.Bernard dog, etc.

6. Heat — This Mackie product should be situated away from heatsources such as radiators, or other devices which produce heat.

7. Object and Liquid Entry — Care should be taken so that objects donot fall on and liquids are not spilled into this Mackie product.

8. Damage Requiring Service — This Mackie product should be servicedonly by qualified service personnel when:

A. Objects have fallen, or liquid has spilled into thisMackie product; or

B. This Mackie product has been exposed to rain; or

C. This Mackie product does not appear to operatenormally or exhibits a marked change in perfor-mance; or

D. This Mackie product has been dropped, or itschassis damaged.

CONTENTSINTRODUCTION....................................................... 3HOOKUP DIAGRAMS............................................... 4

Quick Start ........................................................ 4CONNECTIONS........................................................ 6PLACEMENT ............................................................ 6RIGGING .................................................................. 7

SERVICE INFO ......................................................... 8Warranty Service ............................................... 8Troubleshooting ................................................. 8Repair ............................................................... 8

CARE AND MAINTENANCE...................................... 9C200 SPECIFICATIONS.......................................... 10C200 LIMITED WARRANTY .................................... 11

Don’t forget to visit our website at www.mackie.comfor more information about this and other Mackie products.

http://www.mackie.com

3

Part No. 0008986 Rev. A 1/04©2004 LOUD Technologies Inc. All Rights Reserved.

INTRODUCTION

The CrossoverThis unique Low Impedance Compen-

sated Crossover (LICC) design placesinductors in series with the woofer whosevalues are markedly lower than conven-tional designs. This reduces the amount ofenergy that is typically wasted as heat andincreases the amount of energy that istransformed into real acoustic power. It alsoincorporates dynamic protection for thecompression driver from non-linear signals.

The CabinetThe C200 cabinet was designed to be the

strongest molded composite cabinet on theplanet. This material is as strong as con-crete, and rigid enough to preventunwanted vibrations and standing waves inthe cabinet. It has built-in fly points forhanging, and a socket in the bottom formounting on a tripod stand. Although it isan exceptional choice for installed soundsituations, its light weight and durable fin-ish also make it ideal for portable soundsystem use. The asymmetrical trapezoidaldesign of the cabinet also makes it easy touse as a floor wedge for stage monitor appli-cations.

The C200 offers a portable, lightweightsolution for a variety of high-poweredsound reinforcement applications.

Thank you for choosing the Mackie C200sound reinforcement loudspeakers.

The C200 is a portable two-way loud-speaker system, specifically designed tocomplement our PPM Series line of profes-sional powered mixers. They are capable ofextremely high sound pressure levels, anddesigned to give you the best performance ofany portable compact loudspeaker in itsclass and price range.

The TransducersThe C200 features a 10-inch high-power

low-frequency woofer and a 1.4-inch tita-nium diaphragm high-output compressiondriver. The woofer incorporates technologyused in large-format touring systems and,with a precision 2-inch voice coil, is virtu-ally indestructible.

The high-frequency compression driveris mounted on an acoustically non-resonantexponential waveguide, providing a wide,controlled dispersion pattern and precise re-production of the critical upper mid-rangeand high-frequencies. The result is an unbe-lievably smooth off-axis response that allowseveryone in the audience to experience thesame high-resolution audio no matterwhere they are seated.

Each driver has been specifically designedby our engineers for optimum performancein a lightweight high-strength cabinet.

4

Mixer orPreamplifier

RightLine levelOutput

LeftLine level

Output

1202-VLZPRO

StereoPower Amplifier

C300C200

INPUT THRUPARALLEL

SERIAL NUMBER MANUFACTURING DATE

DESIGNED BY MACKOIDS IN WHITINSVILLE, MA AND WOODINVILLE, WA, USA MANUFACTURED IN CHINA • FABRIQUE AU CHINE • COPYRIGHT ©2003

THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES.: "MACKIE", AND THE "RUNNING MAN" FIGURE • PATENT PENDING

C200

INPUT THRUPARALLEL




HOOKUP DIAGRAMS2. Connect the “Speaker Output” from

your power amplifier (or powered mixer)to the INPUT connector on the C200.

3. Turn on your mixing console (or othersignal source).

4. Turn on the amplifier. Turn up itsvolume or gain control(s) as recom-mended by the manufacturer.

5. Start the signal source, whether it bespeaking into a microphone or starting aCD player. Adjust the volume controlson the mixer (or other signal source) fornormal operation.

Quick StartMake all initial connec-tions with the powerswitches OFF on allequipment. Make sure allmaster volume, level, or

gain controls are all the way down.1. Connect the line-level outputs from

your mixing console (or other signalsource) to the inputs of your poweramplifier.

C200: WITH A MIXER AND POWER AMPLIFIER

MAXIMUM NUMBER OF SPEAKERS IN PARALLEL IS 2 PER POWERED MIXER OR AMPLIFIED CHANNEL

POWERED MIXER

C200: WITH A MACKIE POWERED MIXER, AND USING THE THRU JACK

5

Mixer orPreamplifier

RightLine levelOutput

LeftLine level

Output

INPUT THRUPARALLEL




1202-VLZPRO

StereoPower Amplifier

C200

INPUT THRUPARALLEL




C200

INPUT THRUPARALLEL




C200

INPUT THRUPARALLEL




C200

StereoPower

AmplifierPole

MountTripodMount

C200 C200

Line-LevelHi-Pass Out

FullRange

PowerCord

SWA1501Plays the LowFrequencies

1202-VLZPRO

ACTIVE

C200 C200

C200: WITH A MIXER AND POWER AMPLIFIER, AND USING THE THRU JACK

C200: BIAMPING WITH A POWERED SUBWOOFER

The C200 can beused with a MackieSWA1501 (or SWA1801)subwoofer to create anincredibly powerfulsystem.

The active crossoverinside the subwoofersplits the full-rangestereo input signal intotwo ranges. The SWA1501sums the left and rightlow-frequency rangeand plays it through itsbuilt-in amplifier and15-inch woofer. It sendsthe stereo high-pass rangeto the C200s, via an ex-ternal power amplifier.

The C200 can be polemounted on top of theSWA1501 or 1801 asshown.

6

CONNECTIONSThe C200 has 1/4˝ TS and Speakon™-

style INPUT and THRU connectors. Theconnectors are wired in parallel, so use onlyone of the input connectors (either 1/4˝ TSor Speakon-style).

INPUT THRUPARALLEL

C200 Connector Panel

Normally, you would use only oneTHRU connector, but it is possible to useboth THRU connectors. Keep in mind thatall the speakers are connected in parallel, soyou want to be sure not to go below theminimum impedance requirements foryour amplifier.

The C200 has a nominalimpedance of 8 ohms.Two C200s in parallelequals 4 ohms.Three C200s in parallelequals 2.7 ohms.Four C200s in parallelequals 2 ohms.

Use high-quality speaker cable as recom-mended by the manufacturer.

DO NOT use coaxialshielded cable like a gui-tar cord to make speakerconnections. They arenot designed to handlethe high currents re-quired to drive aloudspeaker.

The 1/4˝ TS jack is wired as follows:Tip = Signal (“+” or hot)Sleeve = Ground (“–” or cold)

SLEEVE ("–" or COLD)

TIP ("+" or HOT)

TIPSLEEVE

TIP

SLEEVE

1/4˝ TS Connector

The Speakon-style connector is wired asfollows:Pin 1+ = Signal (“+” or hot)Pin 1– = Ground (“–” or cold)

Speakon-style Connector

PLACEMENTThe C200 loudspeakers are designed to sit

on the floor, a tabletop, or to fit on a standardtripod speaker stand. They can also be sus-pended by the rigging points, which requiresinstalling the optional accessory plates onthe top and bottom of the cabinet.

You can lay the cabinet down on its sideand use the C200 as a floor monitor. Theasymmetrical trapezoidal shape of the cabinetprovides a perfect angle for aiming up towardperformers from the front of the stage.

Warning: Do not stackspeakers in a column.This is to avoid thedanger of topplingspeakers.

As with any loudspeakers, protect themfrom moisture. If you are setting them upoutdoors, make sure they are under cover ifyou expect rain.

COLD

HOT1+

1+

1–

1–

2–2+

7

Room AcousticsThe C200 loudspeakers are designed to

sound as neutral as possible; that is, to re-produce the input signal as accurately aspossible, monitoring the audio signal ratherthan changing it.

Room acoustics play a crucial role in theoverall performance of a sound system.However, the wide high-frequency dispersionof the C200 helps to minimize the problemsthat typically arise.

Top

900 Dispersionup to 20 kHz

900

Here are some other placement tips:• Avoid placing loudspeakers in the

corners of a room. This increases thelow frequency output and can cause thesound to be muddy and indistinct.

• Avoid placing loudspeakers against awall. This, too, increases the lowfrequency output, though not as muchas corner placement. However, if you doneed to reinforce the low frequencies,this is a good way to do it.

• Avoid placing the speakers directly on ahollow stage floor. A hollow stage canresonate at certain frequencies, causingpeaks and dips in the frequency re-sponse of the room. It’s better to placethe loudspeakers on a sturdy table ortripod stands.

• Position the loudspeakers so the high-frequency drivers are 2 to 4 feet aboveear level for the audience (make allow-ances for a standing/dancing in theaisles audience). High frequencies arehighly directional and tend to be absorbedmuch easier than lower frequencies. Byproviding direct line-of-sight from theloudspeakers to the audience, youincrease the overall brightness andintelligibility of the sound system.

• Highly reverberant rooms, like manygymnasiums and auditoriums, are anightmare for sound system intelligibil-

ity. Multiple reflections off the hardwalls, ceiling, and floor play havoc withthe sound. Depending on the situation,you may be able to take some steps tominimize the reflections, such asputting carpeting on the floors, closingdraperies to cover large glass windows,or hanging tapestries or other materialson the walls to absorb some of the sound.However, in most cases, these remediesare not possible or practical. So what doyou do? Making the sound systemlouder generally doesn’t work becausethe reflections become louder, too. Thebest approach is to provide as muchdirect sound coverage to the audience aspossible. The farther away you are fromthe speaker, the more prominent will bethe reflected sound.Use more speakers strategically placedso they are closer to the back of theaudience. If the distance between thefront and back speakers is more thanabout 100 feet, you should use a delayprocessor to time-align the sound.(Since sound travels about 1 foot permillisecond, it takes about 1/10 of asecond to travel 100 feet.)

RIGGINGThe C200 cabinets are fitted with four

M5 insert points on the top and bottom forinstalling an optional accessory plate thatallows the speaker to be flown.

WARNING: Never at-tempt to suspend theC200 loudspeakers bytheir handles. If you wantto suspend them, use the

accessory plate only. Consult a professionalrigger or structural engineer prior to sus-pending loudspeakers from a structure notintended for that use. Always know theworking load limit of the structure support-ing the loudspeaker array. Always makesure that the rigging hardware minimumrating is at least five times the actual load.

M5 inserts for mounting rigging accessory plate

BottomPoleMountTop

8

Poor bass performance

• Check the polarity of the connectionsbetween the amplifier and the loud-speakers. You may have your positiveand negative connections reversed atone end of one cable.

It hurts when I touch my arm, or my leg,or even my head!

• You have a broken finger.

Bad sound!

• Is it loud and distorted? Follow theprocedures described in the “QuickStart” section to verify that the levelsare set properly.

• Are all the connections secure? It’s agood idea to periodically clean allelectrical connections with a non-lubricating electrical contact cleaner.

• Keep practicing.

RepairService for the C200 is available only

from one of our authorized domestic ser-vice stations or at the factory, located insunny Woodinville, Washington. Service forloudspeakers living outside the UnitedStates can be obtained through local dealersor distributors.

If your Mackie loudspeaker needs ser-vice, follow these instructions:1. Review the preceding troubleshooting

suggestions. Please.2. Call Tech Support at 1-800-898-3211,

7 AM to 5 PM PST, to explain theproblem and request an RA (ReturnAuthorization) number. Have yourspeaker’s serial number ready. Youmust have an RA number beforeyou can obtain service at the factoryor an authorized service center.

3. Keep this owner’s manual. We don’tneed it to repair the loudspeaker.

SERVICE INFO

Warranty ServiceDetails concerning Warranty Service are

spelled out on page 11 of this manual.If you think your loudspeaker has a

problem, please do everything you can toconfirm it before calling for service, includ-ing reading through the followingTroubleshooting section. Doing so mightsave you from being deprived of yourMackie loudspeaker.

Of all Mackie products returned for ser-vice (which is hardly any at all), many arecoded “CND” — Could Not Duplicate,which usually means the problem lay some-where else in the system. These may soundobvious to you, but here are some thingsyou can check:

Troubleshooting

No sound!• Are the level controls on the mixer or

amplifier turned all the way down?Follow the procedures in the “QuickStart” section on page 4 to verify that allthe volume controls in the system areproperly adjusted.

• Is the signal source working (and makingunion scale)? Make sure all the connect-ing cables are in good repair and securelyconnected at both ends.

One side is way louder than the other!• Are the level controls set the same for

both channels on the mixer and ampli-fier?

• Check the PAN control on the signalsource. It may be turned too far to oneside. If you’re using a stereo signalsource, it may be delivering an out-of-balance stereo signal.

• Try swapping sides: Switch the speakercables coming from the amplifier at theamplifier end. If the other side is loudernow, the problem is with the amplifier,the mixer, or the signal source.

9

CARE AND MAINTENANCEYour Mackie loudspeakers will provide

many years of reliable service if you followthese simple guidelines:• Avoid exposing the loudspeakers to

moisture. If they are set up outdoors, besure they are under cover if you expectrain.

• Avoid exposure to extreme cold (belowfreezing temperatures). If you mustoperate the loudspeakers in a coldenvironment, warm up the voice coilsslowly by sending a low-level signalthrough them for about 15 minutesprior to high-power operation.

• Use a slightly damp cloth with a mildsoap solution to clean the cabinets.Avoid getting moisture into any of theopenings of the cabinet, particularlywhere the drivers are located.

4. Pack the loudspeaker in its originalpackage, including protective wrap,endcaps and box. This is very impor-tant. Do not use styrofoam peanuts!When you call for the RA number, pleaselet Tech Support know if you need newpackaging. Mackie is not responsible forany damage that occurs due to non-factory packaging.

5. Include a legible note stating your name,shipping address (no P.O. boxes),daytime phone number, RA number,and a detailed description of the prob-lem, including how we can duplicate it.

6. Write the RA number in BIG PRINTon top of the box.

7. Ship the loudspeaker to us. We suggestinsurance for all forms of cartage. Shipto this address:

MACKIESERVICE DEPARTMENT16220 Wood-Red Rd. NEWoodinville, WA 98072

8. We’ll try to fix the loudspeaker withinfive business days. Ask Tech Supportfor the latest turnaround times whenyou call for your RA number. Wenormally send everything back prepaidby ground shipping. However, if yourush your loudspeaker to us by next-dayair, we’ll treat it in kind by shipping itback to you the same way it was received.This paragraph does not necessarilyapply to non-warranty service.

Need Help?You can reach a technical support representative

Monday through Fridayfrom 7 AM to 5 PM PST at:

1-800-898-3211After hours, visit www.mackie.com and click Support,

or email us at: [email protected]


10

C200 SPECIFICATIONSSystem Specifications

Frequency Response (–3 dB)89 Hz – 20 kHz

Frequency Range (–10 dB)59 Hz – 22 kHz

Maximum SPL Long-term @ 1m 118 dBLow-Frequency Crossover Type

6 dB/octave, time offset correctedHigh-Frequency Crossover Type

12 dB/octaveCrossover Frequency 1800Hz

AudioInput Type Speakon®-style

1/4-inch TS phone jackInput Impedance 8 ohmsPower Handling

RMS: 200 wattsMusic: 350 wattsPeak: 500 watts

Operating Temperature Range–10ºC to 45ºC(14ºF to 113ºF)

Transducer SpecificationsLow-Frequency Transducer

Diameter 10 in/250 mmVoice Coil Diameter 2.0 in/51 mmSensitivity (1W@1m) 96 dBFrequency Range 59 Hz – 3000 Hz

High-Frequency Driver and Horn

Diaphragm Diameter 1.4 in/36 mmHorn Exit Diameter 1 in/24.5 mmDiaphragm Material TitaniumSensitivity (1W@1m) 104 dBFrequency Range 1000 Hz – 20,000 HzHorn Type

Composite: Exponential and ConicalMouth Size

12 in/305 mm W x 7 in/178 mm HHorizontal Coverage

90º (1 kHz – 20 kHz)Vertical Coverage

80º (1 kHz – 20 kHz)

Safety FeaturesDriver Protection

Dynamic protection for compression driver

Construction FeaturesBasic Design Asymmetrical TrapezoidalMaterial PolypropyleneFinish Grey, textured finishHandles One on left side, one on topGrille Perforated metal with weather-

resistant coating

Physical PropertiesHeight 20.75 in/527 mmWidth 13.10 in/333 mmDepth 12.25 in/311 mmWeight 26.0 lb/11.8 kg

Mounting MethodsOptional accessory plates for topand bottom of enclosure

DisclaimerSince we are always striving to make our

products better by incorporating new and improvedmaterials, components, and manufacturing methods,we reserve the right to change these specifications atany time without notice.

“Mackie” and the “Running Man” figure areregistered trademarks of LOUD Technologies Inc.

All other brand names mentioned are trade-marks or registered trademarks of their respectiveholders, and are hereby acknowledged.

©2004 LOUD Technologies Inc.All Rights Reserved.

11

A. LOUD Technologies warrants all materials,workmanship and proper operation of this C200 fora period of two years from the original date ofpurchase. If any defects are found in the materials orworkmanship or if the product fails to functionproperly during the applicable warranty period,LOUD Technologies, at its option, will repair orreplace the product. This warranty applies only toequipment sold and delivered within the U.S. byLOUD Technologies or its authorized dealers.B. Failure to register online or return the productregistration card will not void the two-year warranty.C. Service and repairs of Mackie products are to beperformed only at the factory (see D below) OR at anAuthorized Mackie Service Center (see E below).Unauthorized service, repairs, or modification willvoid this warranty.D. To obtain factory service:

1. Call LOUD Technologies at 800/898-3211,7 AM to 5 PM Monday through Friday (PacificTime) to get a Return Authorization (RA). Productsreturned without an RA number will be refused.2. Pack the C200 in its original shipping carton.If you do not have the carton, just ask for onewhen you get your RA number, and we’ll send ashipping carton out promptly. More informationon packing can be found in the Service section ofthis manual. Do not use “packing peanuts,”shredded newpapers, or other material withsmall particles to pack the product. Please sealthe Mackie product in a plastic bag.3. Also include a note explaining exactly how toduplicate the problem, a copy of the sales receiptwith price and date showing, and your returnstreet address (no P.O. boxes or route numbers,please!). If we cannot duplicate the problem orestablish the starting date of your LimitedWarranty, we may, at our option, charge forservice time.4. Ship the product in its original shippingcarton, freight prepaid to:

MACKIESERVICE DEPARTMENT

16220 Wood-Red Road NEWoodinville, WA, 98072, USA

IMPORTANT: Make sure that the RA number isplainly written on the shipping carton.E. To obtain service from an Authorized Mackie ServiceCenter:

1. Call LOUD Technologies at 800/898-3211,7 AM to 5 PM Monday through Friday (PacificTime) to get: 1) The name and address of yournearest Authorized Mackie Service Center and2) A return authorization (RA). You must havean RA number before taking your unit to aservice center.2. Make sure that you have a copy of yourloudspeaker’s sales receipt from the store whereyou bought the product. It is necessary to establishpurchase date and thus determine whether or notyour loudspeaker is still under warranty. If youcan't find it, the Authorized Service Center maycharge you for repairs even if your loudspeaker isstill covered by the Two-Year Limited Warranty.3. Make sure that the problem can be duplicated.If you bring your loudspeaker to an AuthorizedService Center and they can't find anythingwrong with it, you may be charged a service fee.4. If the Authorized Mackie Service Center islocated in another city, pack the loudspeaker in

its original shipping carton. More information onpacking can be found in the Service section ofthis manual.5. Contact the Authorized Mackie Service Center toarrange service or bring the active monitor to them.

F. LOUD Technologies and Authorized MackieService Centers reserve the right to inspect anyproducts that may be the subject of any warrantyclaims before repair or replacement is carried out.LOUD Technologies and Authorized Mackie ServiceCenters may, at their option, require proof of theoriginal date of purchase in the form of a dated copyof the original dealer’s invoice or sales receipt. Finaldetermination of warranty coverage lies solely withLOUD Technologies or its Authorized Service Centers.G. Mackie loudspeakers returned to LOUDTechnologies and deemed eligible for repair orreplacement under the terms of this warranty willbe repaired or replaced within thirty days of receiptby LOUD Technologies. LOUD Technologies mayuse refurbished parts for repair or replacement ofany product. Products returned to LOUD Technolo-gies that do not meet the terms of this Warranty willbe repaired and returned C.O.D. with billing forlabor, materials, return freight, and insurance.Products repaired under warranty at the factory willbe returned freight prepaid by LOUD Technologiesto any location within the boundaries of the USA.H. LOUD Technologies warrants all repairsperformed for 90 days or for the remainder of thewarranty period. This warranty does not extend todamage resulting from improper installation,misuse, neglect or abuse, or to exterior appearance.This warranty is recognized only if the inspectionseals and serial number on the unit have not beendefaced or removed.I. LOUD Technologies assumes no responsibility forthe quality or timeliness of repairs performed byAuthorized Mackie Service Centers.J. This warranty is extended to the originalpurchaser and to anyone who may subsequentlypurchase this product within the applicablewarranty period.K. This is your sole warranty. LOUD Technologiesdoes not authorize any third party, including anydealer or sales representative, to assume anyliability on behalf of LOUD Technologies or to makeany warranty for LOUD Technologies Inc.L. THE WARRANTY GIVEN ON THIS PAGE IS THESOLE WARRANTY GIVEN BY LOUD TECHNOLOGIESINC. AND IS IN LIEU OF ALL OTHER WARRANTIES,EXPRESS AND IMPLIED, INCLUDING THEWARRANTIES OF MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE. THEWARRANTY GIVEN ON THIS PAGE SHALL BESTRICTLY LIMITED IN DURATION TO TWO YEARSFROM THE DATE OF ORIGINAL PURCHASE FROMAN AUTHORIZED MACKIE DEALER. UPONEXPIRATION OF THE APPLICABLE WARRANTYPERIOD, LOUD TECHNOLOGIES INC. SHALLHAVE NO FURTHER WARRANTY OBLIGATIONOF ANY KIND. LOUD TECHNOLOGIES INC.SHALL NOT BE LIABLE FOR ANY INCIDENTAL,SPECIAL, OR CONSEQUENTIAL DAMAGES THATMAY RESULT FROM ANY DEFECT IN THEMACKIE PRODUCT OR ANY WARRANTY CLAIM.Some states do not allow exclusion or limitation ofincidental, special, or consequential damages or alimitation on how long warranties last, so some ofthe above limitations and exclusions may not applyto you. This warranty provides specific legal rightsand you may have other rights which vary fromstate to state.

Please keep your sales receipt in a safe place.C200 LIMITED WARRANTY

12

LOUD Technologies Inc.16220 Wood-Red Road NE • Woodinville, WA 98072 • USA

US and Canada: 800.258.6883

Europe, Asia, Central and South America: 425.487.4333

Middle East and Africa: 31.20.654.4000

Fax: 425.487.4337 • www.mackie.com

E-mail: [email protected]


C200 Two-Way Loudspeaker User's Manual · same high-resolution audio no matter ... MA AND...

Documents

Transcript of C200 Two-Way Loudspeaker User's Manual · same high-resolution audio no matter ... MA AND...