C 011 eadline3pt/1mm Compact Modules · CKR Carriage/ Connection plate Size 1) Lubrica-tion Version...
Transcript of C 011 eadline3pt/1mm Compact Modules · CKR Carriage/ Connection plate Size 1) Lubrica-tion Version...
C 01_1 Headline_36pt/14.4mmC 01_2 Subheadline_15pt/7.2mm
Compact Modules Catalog addition: Lubrication / Cover „Resist“
2
Bosch Rexroth AG, R999001350 (2017-03)
2
Catalog addition Lubrication
Compact Modules - catalog addition |
Bosch Rexroth AG, R999001350 (2017-03)
Identification system for short product names
Content
Short product name Example: C K K – 070 – NN – 1System = Compact Modules (C)Linear guide = Ball Rail System (K)Drive = Ball screw drive (K)
Toothed belt drive (R)
Size 070 / 090 / 110 / 145 / 200
Version = Standard version (N)
Generation = Product generation 1
Product description 4
Configuration 6CKK 6CKR 8
Lubrication 9Lube version LSS 9Lube version LPG 9Lube version LCF/LCO 10
Dimensional drawings 11
Lubricants 12
Product description 14
Configuration 15
Dimensional drawings 16
Operating conditions 18Further information 19Request/order form 20
Catalog addition Cover „Resist“
Service and information
333
Compact Modules CKK
Bosch Rexroth AG, R999001350 (2017-03)
| Compact Modules - catalog addition
Catalog addition Lubrication
, lubrication
Compact Modules CKR
4
Bosch Rexroth AG, R999001350 (2017-03)
44 Compact Modules – catalog addition, lubrication |
Bosch Rexroth AG, R999001350 (2017-03)
Product descriptionFurther development of the lubrication concept for Compact ModulesWith new options for various lubrication concepts, Bosch Rexroth is upgrading the product portfolio to follow the market trend.This catalog addition must always be used in conjunction with the “Compact Modules” main catalog.Please refer to the main catalog for all technical data such as dimensions, etc.
Two drive versions: ▶ Compact Modules CKK with Ball Rail System and ball screw drive ▶ Compact Modules CKR with Ball Rail System and toothed belt drive
Four different lube versions ▶ Standard lubrication (LSS) ▶ Preserved (LPG) ▶ Carriage with connection plate prepared for connection to one-point lubrication systems for liquid grease (LCF) ▶ Carriage with connection plate prepared for connection to one-point lubrication systems for oil (LCO)
Versions for oil and liquid grease lubrication prepared for connection to one-point lubrication systems ▶ High operational reliability through automated relubrication ▶ Need-based maintenance reduces consumption of lubricant, while ensuring high availability ▶ More degrees of freedom as lubrication is dependent on position and mounting location ▶ Low-cost unmanned maintenance
Notes on the lube version
LSS: ▶ Initial lubrication by Bosch Rexroth ▶ Relubrication using manual grease gun
LPG: ▶ Ball Rail System and ball screw drive ▶ Relubrication using manual grease gun ▶ Basic lubrication required
LCF: ▶ Prepared for connection to one-point lubrication systems for liquid grease (NLGI grade 00 in accordance with DIN 51818) ▶ Lubrication with liquid grease only via single-line piston distributor system ▶ Basic lubrication required
LCO: ▶ Prepared for connection to one-point lubrication systems for oil ▶ Oil lubrication only via single-line piston distributor system ▶ Runner block and ball screw drive nut with integrated non-return valves ▶ Basic lubrication required
Product description
555
Compact Modules CKKLube version LSS, LPG
▶ Grease lubrication with manual grease gun via frame, carriage or via connection plate
Compact Modules CKRLube version LSS, LPG
▶ Grease lubrication with manual grease gun via frame, carriage or via connection plate
Connection plates Connection plates
| Compact Modules – catalog addition, lubrication
Bosch Rexroth AG, R999001350 (2017-03)
Lube version LCF, LCO
▶ 3 lube fittings ▶ Prepared for connection to
one-point lubrication systems
Lube version LCF, LCO
▶ 2 lube fittings ▶ Prepared for connection to
one-point lubrication systems
Lube version LSS, see main catalog Lube version LSS, see main catalog
Product description
6
Bosch Rexroth AG, R999001350 (2017-03)
6 Compact Modules – catalog addition, lubrication |
Bosch Rexroth AG, R999001350 (2017-03)
1) See Compact Modules main catalog for technical data
CKK
Size
1)
Lubr
icat
ion
Vers
ion
Line
ar g
uide
Drive
Screw support
Carriage
Motor attachment
Motor Cover Switching system
Documen-tation
Scre
w jo
urna
l BASA d0 x P Connection plate
8 x
2.5
12 x
2
12 x
5
12 x
10
16 x
5
16 x
10
16 x
16
20 x
5
20 x
20
25 x
10
20 x
40
32 x
5
32 x
10
32 x
20
32 x
32
wit
hout
dr
ive
Without With
Lca (mm) Option Lca
(mm) Option
CK
K-07
0
LPG
see
Com
pact
Mod
ules
mai
n ca
talo
g
Ø 6 mm 31 – – – – – – – – – – – – – – 50 – 73 302 95 341
see Compact Modules main catalog
CK
K-09
0 LPG
Ø 8 mm
33 31 32 – – – – – – – – – – – 50
– 100 302 125 341
–variable
min = 101 max = 235
305 – –
LCF– 03 01 02 – – – – – – – – – – – –
– – – 125 141
LCO – – – 125 241
CK
K-11
0 LPG
Ø 11 mm
– – – – 31 32 33 – – – – – – – – 50
– 124 302 155 341
–variable
min = 125 max = 289
305 – –
LCF– – – – 01 02 03 – – – – – – – – –
– – – 155 141
LCO – – – 155 241
CK
K-14
5
LPG
Ø 14 mm
– – – – – – –31 32 33 –
– – – –
50
– 149 302 190 341
– – – 34 307 309
– – – – – – –31 32 33 –
– – – – –variable
min = 150 max = 349
305 – –
– – – 34 310 – –
LCF – – – – – – –21 22 23 –
– – – – –– – – 190 141
– – – 24 – 109
LCO – – – – – – –21 22 23 –
– – – – –– – – 190 241
– – – 24 – 209
CK
K-20
0
LPG
Ø 16 mm
– – – – – – – – – – – 31 32 33 34
50 Without 254.5 311
– ––
1 312
2 313
3 314
50variable
min = 255.5 max = 429.5
318 – –
–
Without
– – 305
341
1 326
2 327
3 328
LCF – – – – – – – – – – – 01 02 03 04 –
Without
– – 305
141
1 126
2 127
3 128
LCO – – – – – – – – – – – 01 02 03 04 –
Without
– – 305
241
1 226
2 227
3 228
Configuration
777 | Compact Modules – catalog addition, lubrication
Bosch Rexroth AG, R999001350 (2017-03)
Size
1)
Lubr
icat
ion
Vers
ion
Line
ar g
uide
Drive
Screw support
Carriage
Motor attachment
Motor Cover Switching system
Documen-tation
Scre
w jo
urna
l BASA d0 x P Connection plate
8 x
2.5
12 x
2
12 x
5
12 x
10
16 x
5
16 x
10
16 x
16
20 x
5
20 x
20
25 x
10
20 x
40
32 x
5
32 x
10
32 x
20
32 x
32
wit
hout
dr
ive
Without With
Lca (mm) Option Lca
(mm) Option
CK
K-07
0
LPG
see
Com
pact
Mod
ules
mai
n ca
talo
g
Ø 6 mm 31 – – – – – – – – – – – – – – 50 – 73 302 95 341
see Compact Modules main catalog
CK
K-09
0 LPG
Ø 8 mm
33 31 32 – – – – – – – – – – – 50
– 100 302 125 341
–variable
min = 101 max = 235
305 – –
LCF– 03 01 02 – – – – – – – – – – – –
– – – 125 141
LCO – – – 125 241
CK
K-11
0 LPG
Ø 11 mm
– – – – 31 32 33 – – – – – – – – 50
– 124 302 155 341
–variable
min = 125 max = 289
305 – –
LCF– – – – 01 02 03 – – – – – – – – –
– – – 155 141
LCO – – – 155 241
CK
K-14
5
LPG
Ø 14 mm
– – – – – – –31 32 33 –
– – – –
50
– 149 302 190 341
– – – 34 307 309
– – – – – – –31 32 33 –
– – – – –variable
min = 150 max = 349
305 – –
– – – 34 310 – –
LCF – – – – – – –21 22 23 –
– – – – –– – – 190 141
– – – 24 – 109
LCO – – – – – – –21 22 23 –
– – – – –– – – 190 241
– – – 24 – 209
CK
K-20
0
LPG
Ø 16 mm
– – – – – – – – – – – 31 32 33 34
50 Without 254.5 311
– ––
1 312
2 313
3 314
50variable
min = 255.5 max = 429.5
318 – –
–
Without
– – 305
341
1 326
2 327
3 328
LCF – – – – – – – – – – – 01 02 03 04 –
Without
– – 305
141
1 126
2 127
3 128
LCO – – – – – – – – – – – 01 02 03 04 –
Without
– – 305
241
1 226
2 227
3 228
Configuration
8
Bosch Rexroth AG, R999001350 (2017-03)
8 Compact Modules – catalog addition, lubrication |
Bosch Rexroth AG, R999001350 (2017-03)
CKRCarriage/
Connection plate
Size 1) Lubrica-tion
Version Linear guide
Drive Without with Motor attachment
Motor Switching system
Documen-tationLca
(mm)Option Lca
(mm)Option
CKR-070 LPG
see Compact Modules main catalog
108 302 95 341
see Compact Modules main catalog
CKR-090
LPG 156 302 125 341
LCF – – 125 141
LCO – – 125 241
CKR-110
LPG 215 302 155 341
LCF – – 155 141
LCO – – 155 241
CKR-145
LPG 240 302 190 341
LCF – – 190 141
LCO – – 190 241
CKR-200
LPG 405 302 305 341
LCF – – 305 141
LCO – – 305 2411) See Compact Modules main catalog for technical data
Configuration
999
Carriage without connection plate1)
Carriage with connection plate1)
Size CKK CKR
Lca (mm) Option Lca (mm) Option
070 95 341 95
341
090 125 341 125
110 155 341 155
145 190 309 / 341 190
200 305 326 / 327 / 328 / 341 305
Lca Lca
Size CKK CKRLca (mm) Option Lca (mm) Option Lca (mm) Option
070 73.0 302 – – 108
302
090 100.0 302
Variable
305 156
110 124.0 302 305 215
145 149.0 302 / 307 305 / 310 240
200 254.5 311 / 312 / 313 / 314 318 405
Lca Lca
LW
Lca
| Compact Modules – catalog addition, lubrication
Bosch Rexroth AG, R999001350 (2017-03)
Lube version LPG
1) See Compact Modules main catalog for detail drawing and technical data
Lube version LSS ▶ see Compact Modules main catalog
Lube version
10
Bosch Rexroth AG, R999001350 (2017-03)
10
A
23
11
2
A
Carriage with connection plate1)
Compact Modules – catalog addition, lubrication |
Bosch Rexroth AG, R999001350 (2017-03)
Lube version LCF/LCO
Compact Modules CKK Compact Modules CKR
A Drive side1 Lube fitting, runner block left2 Lube fitting, runner block right3 Lube fitting, ball screw driveLube fittings: Straight connector (SW 9), for Ø4 mm plastic tubes and metal pipes.
1) See Compact Modules main catalog for detail drawing and technical data
Lube version
111111
LcaH6
H5
H5
Ø D
H8
| Compact Modules – catalog addition, lubrication
Bosch Rexroth AG, R999001350 (2017-03)
CKK
Size Lube version option Dimensions (mm)
Lca LCF LCO H5 ⌀D H6 H8
(mm)
070 – – – – – – –090 125 141 241 38 8.5
12.5
3110 155 141 241 40 8.5 3145 190 141 241 52 0 0200 305 141, 126, 127, 128 241, 226, 227, 228 62 0 0
CKR
Size Lube version option Dimensions (mm)
Lca LCF LCO H5 ⌀D H6 H8
(mm)
070 – – – – – – –090 125 141 241 38 8.5
12.5
3110 155 141 241 80 8.5 3145 190 141 241 84 0 0200 305 141 241 84 0 0
Dimensional drawings
Dimensional drawings
12
Bosch Rexroth AG, R999001350 (2017-03)
12 Compact Modules – catalog addition, lubrication |
Bosch Rexroth AG, R999001350 (2017-03)
LubricantsLube version LSS LPG LCF LCOSize CKx-110, -145, -200 CKx-070, -090 CKx-110, -145, -200 CKx-070, -090 CKx-090, -110, -145, -200 CKx-090, -110, -145, -200Initial greasing Dynalub 510 Dynalub 520 Preserved, initial greasing required
(See instructions)required, see instructions required, see instructions
Consistency class NLGI 2 (DIN 51818) NLGI 00 (DIN51818) – NLGI 00 (DIN51818) –Identification KP2K-20 (DIN 51825) GP00K-20 (DIN 51826) – GP00K-20 (DIN 51826) –Lubrication with manual grease gun
yes yes yes – –
Prepared for connection to one-point lubrication systems – – –
• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110, -145, -200: 0,2 cm3
• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110: 0.2 cm3; CKx-145: 0.4 cm3; CKx-200: 0.6 cm3
Lubricant recommendation Dynalub 510 (grease lubri-cant)
(NLGI2 DIN 51818)
Dynalub 520 (liquid grease)
(NLGI00 DIN51818)
Dynalub 510 (grease lubri-cant)
(NLGI2 DIN 51818)
Dynalub 520 (liquid grease) (NLGI00 DIN51818)
Dynalub 520 (liquid grease)(NLGI00 DIN51818)
Shell Tonna S3 M220 (lubricant oil)
Properties • Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C
• Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C
• Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C
• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides• A blend of highly refined mineral base oils and additives• Can be used even when mixed with significant quantities of metalworking fluids
Material numbers R3416 037 00(Cartridge 400 g)
R3416 043 00(Cartridge 400 g)
R3416 037 00(Cartridge 400 g)
R3416 043 00(Cartridge 400 g)
R3416 043 00 (Cartridge 400 g)
–
R3416 035 00(Hobbock 25 kg)
R3416 042 00 (Bucket 5 kg)
R3416 035 00 (Hobbock 25 kg)
R3416 042 00 (Bucket 5 kg)
R3416 042 00(Bucket 5 kg)
–
Alternative lubricants • Tribol GR 100-2 PD• Elkalub GLS 135/N2
• Tribol GR 100-00 PD• Elkalub GLS 135/N00
• Tribol GR 100-2 PD• Elkalub GLS 135/N2• Tribol GR 100-00 PD• Elkalub GLS 135/N00• Dynalub 520
• Tribol GR 100-00 PD• Elkalub GLS 135/N00
• Tribol GR 100-00 PD• Elkalub GLS 135/N00
• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides
Alternative lubricants with H1 approval – –
• Berulub FG H2 SL• Cassida Grease EPS2• VP 874
• Berulub FB 34-00• Elkalub GLS 367/N00 – –
c Notes on lubrication
▶ Follow the instructions for each product. ▶ Do not use lubricants containing solid particles (e.g. graphite or MoS2)! ▶ If you use different lubricants from the ones stated, you may find that relubrication intervals are shorter and that
performance decreases with short stroke and load ratio; in addition, chemical interactions can take place between the plastics, lubricants and the anti-corrosion agents. In addition, pumpability in single-line one-point lubrication systems must be guaranteed.
▶ If using a one-point lubrication system, you must make sure that all the pipes and elements are filled with lubricant and do not contain any air pockets until they are connected to the consumer (carriage).
▶ Pumping or storage tanks for the lubricant must be fitted with a stirrer to guarantee the flow of lubricant (to avoid funneling in the tank).
▶ In the case of relubrication, it is not possible to change from grease to oil lubrication or vice versa. ▶ In the case of environmental influences such as contamination, vibration, jolting, etc., we recommend shortening the
relubrication intervals appropriately. Even under normal operating conditions, the system must be relubricated at the latest after 2 years due to aging of the grease.
▶ Rexroth recommends piston distributors manufactured by SKF. These should be installed as close as possible to the lube fittings of the carriage. Long lines (maximum line length 1 m) and small line diameters should be avoided, and the lines should be laid on an upward slant. Install the lines at a gradient.
▶ If other consumers are connected to the single-line centralized lubrication system, the weakest link in the chain will determine the lubrication cycle time.
▶ Excess lubricant can accumulate inside of the Compact Module or flow out and may lead to contamination of the environment
▶ Never put a Compact Module into operation without basic lubrication.
Lubricants
131313 | Compact Modules – catalog addition, lubrication
Bosch Rexroth AG, R999001350 (2017-03)
Lube version LSS LPG LCF LCOSize CKx-110, -145, -200 CKx-070, -090 CKx-110, -145, -200 CKx-070, -090 CKx-090, -110, -145, -200 CKx-090, -110, -145, -200Initial greasing Dynalub 510 Dynalub 520 Preserved, initial greasing required
(See instructions)required, see instructions required, see instructions
Consistency class NLGI 2 (DIN 51818) NLGI 00 (DIN51818) – NLGI 00 (DIN51818) –Identification KP2K-20 (DIN 51825) GP00K-20 (DIN 51826) – GP00K-20 (DIN 51826) –Lubrication with manual grease gun
yes yes yes – –
Prepared for connection to one-point lubrication systems – – –
• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110, -145, -200: 0,2 cm3
• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110: 0.2 cm3; CKx-145: 0.4 cm3; CKx-200: 0.6 cm3
Lubricant recommendation Dynalub 510 (grease lubri-cant)
(NLGI2 DIN 51818)
Dynalub 520 (liquid grease)
(NLGI00 DIN51818)
Dynalub 510 (grease lubri-cant)
(NLGI2 DIN 51818)
Dynalub 520 (liquid grease) (NLGI00 DIN51818)
Dynalub 520 (liquid grease)(NLGI00 DIN51818)
Shell Tonna S3 M220 (lubricant oil)
Properties • Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C
• Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C
• Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C
• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides• A blend of highly refined mineral base oils and additives• Can be used even when mixed with significant quantities of metalworking fluids
Material numbers R3416 037 00(Cartridge 400 g)
R3416 043 00(Cartridge 400 g)
R3416 037 00(Cartridge 400 g)
R3416 043 00(Cartridge 400 g)
R3416 043 00 (Cartridge 400 g)
–
R3416 035 00(Hobbock 25 kg)
R3416 042 00 (Bucket 5 kg)
R3416 035 00 (Hobbock 25 kg)
R3416 042 00 (Bucket 5 kg)
R3416 042 00(Bucket 5 kg)
–
Alternative lubricants • Tribol GR 100-2 PD• Elkalub GLS 135/N2
• Tribol GR 100-00 PD• Elkalub GLS 135/N00
• Tribol GR 100-2 PD• Elkalub GLS 135/N2• Tribol GR 100-00 PD• Elkalub GLS 135/N00• Dynalub 520
• Tribol GR 100-00 PD• Elkalub GLS 135/N00
• Tribol GR 100-00 PD• Elkalub GLS 135/N00
• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides
Alternative lubricants with H1 approval – –
• Berulub FG H2 SL• Cassida Grease EPS2• VP 874
• Berulub FB 34-00• Elkalub GLS 367/N00 – –
c Use of lubricants with H1 approval:
Loss of H1 approvalH1 lubricants or separating agent (anti-corrosion agent) only have H1 approval if they are available by material type in unmixed condition (including at the lubrication point). A blend of two H1 approval lubricants or separating agents does not have H1 approval. No food industry authorization or approval
Because of the use of H1 lubricants, the Compact Modules do not have authorization or approval for the food industry.
Lubrication of components at the factoryComponents lubricated by the manufacturer at the factory such as deep-groove ball bearings, cover strips, gears, etc. do not use H1 lubricants.
c Compact Modules with Dynalub 520 (NLGI 00 class) initial greasing must not be pre-lubricated with lubricants of consistency class NLGI 2!
For relubrication quantity and relubrication position ⇒ see Compact Modules CKK/Compact Modules CKR instructions.Relubrication intervalWhen using the standard lubrication from the manufacturer:Relubrication interval⇒ see Compact Modules CKK/Compact Modules CKR instructions.Use of Dynalub 520 (NLGI00) instead of Dynalub 510 (NLGI2):The relubrication interval is 75% of the standard relubrication interval ⇒ CKK/CKR instructions.Use of lubricants with H1 approval:First relubrication takes place after 20 km. As a guideline value for relubrication intervals, 50% of the standard relubrication intervals must be applied ⇒ see Compact Modules CKK/Compact Modules CKR instructions.
Lubricants
14
Bosch Rexroth AG, R999001350 (2017-03)
14 Compact Modules – catalog addition, Cover |
Bosch Rexroth AG, R999001350 (2017-03)
Structural design: ▶ Compact Modules with ball screw drive (CKK) ▶ Sizes: CKK -110, -145, -200 ▶ With connection plate ▶ Cover „Resist“
Properties: ▶ Increased protection because of toothed sealing profile ▶ Integrated tape guide at the carriage provides perfect
toothing of the sealing profile ▶ Sealing profile made of FKM material ▶ PWIS free (paint-wetting impairment substances) ▶ Replaceable sealing profile ▶ Short term heat resistance of sealing profile up to 300°C ▶ Suitable for dry chip admission and handling of
components during welding applications
Product descriptionAdvanced lubrication options:
▶ Standard lubrication (LSS) ▶ Preserved (LPG) ▶ Carriage with connection plate prepared for connection to
one-point lubrication systems for liquid grease (LCF) ▶ Carriage with connection plate prepared for connection to
one-point lubrication systems for oil (LCO)
Catalog addition: Cover „Resist“
Strip clampsfor Sealing profile
Sealing profile made of FKM material
Connection plate
Tape guide
Brackets for Cover
Cover plate
Lube fittings forone-point lubrication systems1)
1) See chapter Lubrication
Thoothing sealing profile
Product description
151515 | Compact Modules – catalog addition, Cover
Bosch Rexroth AG, R999001350 (2017-03)
Size
Lubr
icat
ion1
)
Vers
ion
Gui
dew
ay
Dri
ve u
nit
Carriage withconnection plate
Mot
or a
ttac
hmen
t
Mot
or
Cover Switching system3)
Scre
wsu
ppor
t
L ca
(mm
)
Opt
ion
Cover strip
wit
hout
wit
h
Res
ist2
)
CK
K-11
0
LSS
see
Com
pact
Mod
ules
mai
n ca
talo
g
–
155
41
see
Com
pact
Mod
ules
mai
n ca
talo
g
012
LPG – 341
LCF – 141
LCO – 241
CK
K-14
5
LSS –
190
09
– 41
LPG – 309
– 341
LCF – 109
– 141
LCO – 209
– 241
CK
K-20
0
LSS without
305
41
1 26
2 27
3 28
LPG without 341
1 326
2 327
3 328
LCF without 141
1 126
2 127
3 128
LCO without 241
1 226
2 227
3 228
1) See chapter Lubrication2) Not tested with contact of dusts and cooling lubricants.
If you are unsure about using this product, please contact Bosch Rexroth. In the case of prolonged downtimes, a delayed resetting behavior of the sealing profile can occur in the area of the tape guide.
3) Switch mounting and accessories see Compact Modules main catalog 4) Only CKK-200
Without switch
000Without mounting duct
Without socket plug
Magnetic sensor with plug
REED sensor 058
HALL sensorPNP NC contact
059
Magnetic sensor4)
REED sensor 021
Hall-sensor - PNP NC contact 022
Hall-sensor-PNP-NO contact 023
Mounting duct 025
Socket plug 027
Configuration
Configuration
16
Bosch Rexroth AG, R999001350 (2017-03)
16 Compact Modules – catalog addition, Cover |
Bosch Rexroth AG, R999001350 (2017-03)
Size A B2 C H H11 H12 H13 Lca Z1
CKK-110 100 120 16 50 84 44 12 155 60.7
CKK-145 145 155 20 65 105 59 12 190 71.6
CKK-200 200 212 27 100 150 82 24 305 86.4
Dimensional drawings
Z1 = application point of the effective force
Dimensional drawings
171717 | Compact Modules – catalog addition, Cover
Bosch Rexroth AG, R999001350 (2017-03)
18
Bosch Rexroth AG, R999001350 (2017-03)
18 Compact Modules – catalog addition | Service and information
Bosch Rexroth AG, R999001350 (2017-03)
Normal operating conditionsAmbient temperature with Rexroth servo motor 0 °C ... 40 °C, above 40 °C loss of performance
Ambient temperature for mechanical system(No passing below the dew point) –10 °C ... 60 °C
Travel smin1) see Compact Modules main catalog
Contamination2) not permissible
Required and supplementary
documentationFor further instructions and information, please refer to documentation belonging to this product.
You can find PDF files of these documents in the Internet at www.boschrexroth.com/mediadirectory
We would also be pleased to send you the requested documents.
If you are unsure about using this product, please contact Bosch Rexroth.
Operating conditions
1) Minimum travel to ensure a reliable lubrication distribution.2) Cover „Resist“:
Suitable for dry chip admission and handling of components during welding applications. Not tested with contact of dusts and cooling lubricants.
191919
http://www.boschrexroth.com/goto
Service and information | Compact Modules – catalog addition
Bosch Rexroth AG, R999001350 (2017-03)
Further informationBosch Rexroth homepage: http://www.boschrexroth.com
Compact Modules product information: http://www.boschrexroth.com/en/xc/products/product- groups/linear-motion-technology/linear-motion-systems/compact-modules/index
GoTo Europe:
20
Bosch Rexroth AG, R999001350 (2017-03)
20
Company: Responsible person: Address: Department: Telephone: Fax:
QuantityComments:
From
Acceptance of: _____ pcs, ______ per month, _______ per year, per order, or ________________________
1) Only required for carriage options with variable centerline-to-centerline distance. 2) Only required for “Mounting kits for motors according to customer specification”.
Compact Modules – catalog addition | Service and information
Bosch Rexroth AG, R999001350 (2017-03)
Rexroth – Compact Modules
Find your local contact person here:www.boschrexroth.com/addressen
Request/order form
Ordering exampleOrdering data Option Explanation from catalogCompact Module(short product name)
CKK-110-NN-1,715 mm
CKK-110 Compact ModulesLength = 715 mm (1500 max.)
A(main catalog)
Version MF01 Flange/coupling for motor attachment acc. to illustration MF01Linear guide 01 Standard frameDrive 02 Ball screw drive 16 x 10Carriage 141 Carriage with connection plate for one-point
lubrication system for liquid grease (LCF), Lca = 155 mmB
(this catalog)Motor attachment 01 Flange/coupling for MSK 030C motor A
(main catalog)Motor 85 MSK 030C motor with brake
Cover 02 With cover „Resist“B
(this catalog)
1. Switch 21 REED sensor (delivered as separate part)
A(main catalog)
2. Switch 22 HALL sensor, PNP NC (delivered as separate part)3. Switch 21 REED sensor (delivered as separate part)Mounting duct / cable duct 25 Mounting duct (delivered as separate part)Socket plug 17 Socket-plug, loose (delivered as separate part)Documentation 01 Standard report
212121Service and information | Compact Modules – catalog addition
Bosch Rexroth AG, R999001350 (2017-03)
A
B
22
Bosch Rexroth AG, R999001350 (2017-03)
22 Compact Modules – catalog addition, lubrication | Notice
Bosch Rexroth AG, R999001350 (2017-03)
232323Notice | Compact Modules – catalog addition, lubrication
Bosch Rexroth AG, R999001350 (2017-03)
Find your local contact person here:www.boschrexroth.com/contact
Bosch Rexroth AGErnst-Sachs-Straße 10097424 Schweinfurt, GermanyTel. +49 9721 937-0 Fax +49 9721 937-275www.boschrexroth.com
R999001350 (2017-03)© Bosch Rexroth AG 2017Subject to changes!
The data specified above only serves to describe the product.Since our products undergo continuous further development, no statement regarding any particular quality or suitability for any particular use can be derived from this information. The information does not release the user from making his/her own inspections and evaluations. It must be remembered that our products are subject to a natural process of wear and aging.