Burn Spec Rl 9
20
document.xls Instructions Burner Specification Form Instructions 1 Burner Specification is adapted from engineering standards to define process burner 2 This form consists of three pages with space for application notes on the last page. 3 Select your preferred engineering units by choosing a tab at the bottom of this scre engineering units are: 4 Individual field descriptors of engineering units and heating value basis are availa 5 Information required for burner selection and sizing is highlighted in yellow. 6 Only one burner application may be specified on this worksheet form. 7 If you have questions regarding this data sheet, contact John Zink Company burner Pr John Zink Company, LLC Phone: 918-234-2701 Burner Process Eng. Group Toll Free in USA: 888-495-2665 11920 E Apache Street Fax: 918-234-1806 Tulsa, Oklahoma 74116 Email: [email protected] USA Web: www.johnzink.com REVISED: August, English Metric S.I. Units customization. (i.e. "mm w.c." or "[LHV]")
Transcript of Burn Spec Rl 9
document.xls Instructions
Burner Specification Form Instructions
1 Burner Specification is adapted from engineering standards to define process burner applications.2 This form consists of three pages with space for application notes on the last page.3 Select your preferred engineering units by choosing a tab at the bottom of this screen. Available
engineering units are:4 Individual field descriptors of engineering units and heating value basis are available for user
5 Information required for burner selection and sizing is highlighted in yellow.6 Only one burner application may be specified on this worksheet form.7 If you have questions regarding this data sheet, contact John Zink Company burner Process Eng group:
John Zink Company, LLC Phone: 918-234-2701Burner Process Eng. Group Toll Free in USA: 888-495-266511920 E Apache Street Fax: 918-234-1806Tulsa, Oklahoma 74116 Email: [email protected] Web: www.johnzink.com
REVISED: August, 2003
English Metric S.I. Units
customization. (i.e. "mm w.c." or "[LHV]")
document.xls English Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 REVISED: August, 2003 1 of 3
PURCHASER: JOB NUMBER:
OWNER: LOCATION:HEATER GENERAL DATA REV
1 HEATER EQUIPMENT NUMBER 0
2 HEATER SERVICE 0
3 HEATER MANUFACTURER 0
4 TYPE OF HEATER VC [Vertical Cylindrical] or BOX or CABIN 0
5 SETTING REFRACTORY THICKNESS inch 0
6 HEATER CASING THICKNESS inch 0
7 FIREBOX INTERIOR HEIGHT from FLOOR TO ARCH inch 0
8 FIREBOX INTERIOR LENGTH from WALL TO WALL inch 0
9 FIREBOX WIDTH between TUBES CENTERLINE TO CENTERLINE inch 0
10 TUBE CIRCLE DIAMETER [VERTICAL CYLINDRICAL HEATER] inch 0
11 COMBUSTION AIR PLENUM COMMON or INDIVIDUAL 0
BURNER DATA12 TYPE OF BURNER STANDARD or LOW NOx or B.A.C.T. 0
13 BURNER PROJECT CLASSIFICATION NEW or REPLACE or RETROFIT 0
14 BURNER MODEL NUMBER 0
15 QUANTITY of BURNERS REQUIRED 0
16 FIRING ORIENTATION UPFIRED or DOWNFIRED or HORIZONTAL 0
17 BURNER INSTALLED LOCATION ROOF or FLOOR or WALL 0
18 BURNER CENTERLINE TO TUBE CENTERLINE inch 0
19 BURNER CENTERLINE TO ADJACENT BURNER CENTERLINE inch 0
20 BURNER CENTERLINE TO UNSHIELDED REFRACTORY inch 0
21 BURNER CIRCLE DIAMETER [VERTICAL CYLINDRICAL HEATER] inch 0
22 PILOT REQUIRED? YES or NO 0
23 PILOT MODEL 0
24 PILOT IGNITION METHOD MANUAL or ELECTRIC 0
25 FLAME ROD YES or NO 0
26 PILOT FUEL 0
27 FUEL PRESSURE at PILOT psig 0
28 PILOT HEAT RELEASE Btu/hr 0
29 PILOT CONNECTION 1/2" FNPT or 1/2" R.F. 0
30 PILOT IGNITION TRANSFORMER VOLTAGE 120VAC or 220VAC 0
31 PILOT IGNITION TRANSFORMER HOUSING NEMA 4 or NEMA 7 0
OPERATING DATA32 BURNER FUEL TYPE GAS or OIL or GAS & OIL 0
33 HEATER MAXIMUM HEAT RELEASE * [LHV] MMBtu/hr 0
34 DESIGN HEAT RELEASE per BURNER * [LHV] MMBtu/hr 0
35 NORMAL HEAT RELEASE per BURNER * [LHV] MMBtu/hr 0
36 MINIMUM HEAT RELEASE per BURNER * [LHV] MMBtu/hr 0
37 OTHER CONDITION: MMBtu/hr 0
38 OTHER CONDITION: MMBtu/hr 0
39 BURNER TURNDOWN REQUIRED 0
40 EXCESS AIR at DESIGN HEAT RELEASE % 0
41 COMBUSTION AIR SOURCE AMBIENT or PREHEAT 0
42 COMBUSTION AIR TEMPERATURE at BURNER °F 0
43 COMBUSTION AIR RELATIVE HUMIDITY % 0
44 MAXIMUM AVAILABLE DRAFT at BURNER inch w.c. 0
45 HEATER DRAFT TYPE FORCED or NATURAL or INDUCED 0
46 BURNER AIR PRESSURE DROP at DESIGN HEAT RELEASE inch w.c. 0
47 BURNER AIR PRESSURE DROP at NORMAL HEAT RELEASE inch w.c. 0
48 BURNER AIR PRESSURE DROP at MINIMUM HEAT RELEASE inch w.c. 0
49 HEATER ELEVATION ABOVE SEA LEVEL ft 0
50 FLAME LENGTH at DESIGN HEAT RELEASE ft 0
51 FLAME WIDTH or DIAMETER at DESIGN HEAT RELEASE inch 0
API STANDARD 560 and
document.xls English Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
0 0
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 REVISED: August, 2003 0 30-Dec-99 2 of 3
GAS FUEL CHARACTERISTICS REV52 FUEL GAS DESIGNATION 053 HEATING VALUE * [LHV] Btu/scf 054 SPECIFIC GRAVITY [AIR = 1.0] 055 MOLECULAR WEIGHT 056 FUEL TEMPERATURE at BURNER °F 057 FUEL PRESSURE AVAILABLE at BURNER psig 058 FUEL GAS COMPOSITION Volume% 059 Methane 060 Ethane 061 Propane 062 Butane 063 Pentane 064 Hexane plus 065 Cyclopentane 066 Cyclohexane 067 Ethylene 068 Propene 069 Butene 070 Pentene 071 Butadiene 072 Carbon Dioxide 073 Water 074 Oxygen 075 Nitrogen 076 Sulfur Dioxide 077 Hydrogen Sulfide 078 Carbon Monoxide (CO) 079 Ammonia 080 Hydrogen 081 Argon (Ar) 082 Acetylene 083 Benzene 084 TOTAL 0.0 0.0 0.0 0.0 0.0 0
LIQUID FUEL CHARACTERISTICS85 FUEL OIL DESIGNATION 086 HEATING VALUE * [LHV] Btu/lb 087 SPECIFIC GRAVITY 088 HYDROGEN to CARBON RATIO [BY WEIGHT] 089 VISCOSITY [POINT 1] at °F SSU 090 VISCOSITY [POINT 2] at °F SSU 091 DISTILLATION : ASTM INITIAL BOILING POINT °F 092 ASTM MID-POINT °F 093 ASTM END POINT °F 094 FUEL TEMPERATURE at BURNER °F 095 FUEL PRESSURE AVAILABLE at BURNER psig 096 ATOMIZING MEDIUM AIR or STEAM or MECHANICAL or GAS 097 ATOMIZING MEDIUM TEMPERATURE at BURNER °F 098 ATOMIZING MEDIUM PRESSURE at BURNER psig 099 FUEL OIL METALS: Vanadium, Potassium, Sodium, Nickel wppm 0100 FUEL OIL COMPOSITION Weight% 0101 Carbon (C) 0102 Hydrogen (H) 0103 Oxygen (O) 0104 Fixed Nitrogen (N) 0105 Sulfur (S) 0106 Ash 0107 Water 0108 TOTAL 0.0 0.0 0.0 0.0 0.0 0
API STANDARD 560 and
(CH4) (C2H6)(C3H8)(C4H10)(C5H12)(C6 +)(C5H10)(C6H12)(C2H4)(C3H6)(C4H8)(C5H10)(C4H6)(CO2)(H2O)(O2)(N2)(SO2)(H2S)
(NH3)(H2)
(C2H2)(C6H6)
(H2O)
document.xls English Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
0
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 0 30-Dec-99 3 of 3
EMISSION REQUIREMENTS REV
159 HEATER EQUIPMENT NUMBER 0 0 0 0 0
160 BURNER MODEL NUMBER 0 0 0 0 0 0
161 FIREBOX BRIDGEWALL TEMPERATURE °F 0
162 FIREBOX TEMPERATURE AT BURNER LOCATION °F 0
163 FIREBOX TEMPERATURE DETERMINATION MEASURED or ESTIMATED 0
164 NOx (guaranteed) * [LHV] lb/MMBtu 0
165 CO * [LHV] lb/MMBtu 0
166 NOx (estimated) * [LHV] lb/MMBtu 0
167 PARTICULATE * [LHV] lb/MMBtu 0
168 SOx * [LHV] lb/MMBtu 0
169 0
170 NOISE THRESHOLD SPECIFICATION dBA at 3 ft 0
SPECIFICATION OPTIONS171 PRESSURE TAP REQUIRED YES or NO 0
172 SPECIAL GAUGES Specify 0
173 SPECIAL VALVES Specify 0
174 SPECIAL HOSES Specify 0
175 FLANGED FUEL CONNECTIONS YES or NO 0
176 ENGINEERING UNITS on DRAWINGS ENGLISH or METRIC or S.I. 0
177 POSITIVE MATERIAL IDENTIFICATION [PMI] REQUIRED YES or NO 0
178 MILL CERTIFICATIONS REQUIRED YES or NO 0
179 BURNER PERFORMANCE TEST REQUIRED YES or NO 0
180 0
NOTES AND COMMENTS181 0182 0183 0184 0185 0186 0187 0188 0189 0190 0191 0192 0193 0194 0195 0196 0197 0198 0199 0200 0201 0202 0203 0204 0205 0206 0207 0208 0209 0
210 0
API STANDARD 560 and
*CORRECTED TO 3% O2 [DRY BASIS at DESIGN HEAT RELEASE]
document.xls Metric Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 REVISED: August, 2003 12/30/1899 30-Dec-99 1 of 3
PURCHASER: JOB NUMBER:
OWNER: LOCATION:HEATER GENERAL DATA REV
1 HEATER EQUIPMENT NUMBER
2 HEATER SERVICE
3 HEATER MANUFACTURER
4 TYPE OF HEATER VC [Vertical Cylindrical] or BOX or CABIN
5 SETTING REFRACTORY THICKNESS mm6 HEATER CASING THICKNESS mm7 FIREBOX INTERIOR HEIGHT from FLOOR TO ARCH mm8 FIREBOX INTERIOR LENGTH from WALL TO WALL mm9 FIREBOX WIDTH between TUBES CENTERLINE TO CENTERLINE mm10 TUBE CIRCLE DIAMETER [VERTICAL CYLINDRICAL HEATER] mm11 COMBUSTION AIR PLENUM COMMON or INDIVIDUAL
BURNER DATA12 TYPE OF BURNER STANDARD or LOW NOx or B.A.C.T.13 BURNER PROJECT CLASSIFICATION NEW or REPLACE or RETROFIT
14 BURNER MODEL NUMBER
15 QUANTITY of BURNERS REQUIRED
16 FIRING ORIENTATION UPFIRED or DOWNFIRED or HORIZONTAL
17 BURNER INSTALLED LOCATION ROOF or FLOOR or WALL18 BURNER CENTERLINE TO TUBE CENTERLINE mm19 BURNER CENTERLINE TO ADJACENT BURNER CENTERLINE mm20 BURNER CENTERLINE TO UNSHIELDED REFRACTORY mm21 BURNER CIRCLE DIAMETER [VERTICAL CYLINDRICAL HEATER] mm22 PILOT REQUIRED? YES or NO
23 PILOT MODEL
24 PILOT IGNITION METHOD
25 FLAME ROD YES or NO
26 PILOT FUEL
27 FUEL PRESSURE at PILOT psig25 PILOT HEAT RELEASE Btu/hr26 PILOT CONNECTION 1/2" FNPT or 1/2" R.F.27 PILOT IGNITION TRANSFORMER VOLTAGE 120VAC or 220VAC
28 PILOT IGNITION TRANSFORMER HOUSING NEMA 4 or NEMA 7
OPERATING DATA29 BURNER FUEL TYPE GAS or OIL or GAS & OIL
30 HEATER MAXIMUM HEAT RELEASE * [LHV] MMkcal/hr31 DESIGN HEAT RELEASE per BURNER * [LHV] MMkcal/hr32 NORMAL HEAT RELEASE per BURNER * [LHV] MMkcal/hr33 MINIMUM HEAT RELEASE per BURNER * [LHV] MMkcal/hr34 OTHER CONDITION: MMkcal/hr35 OTHER CONDITION: MMkcal/hr36 BURNER TURNDOWN REQUIRED
37 EXCESS AIR at DESIGN HEAT RELEASE %38 COMBUSTION AIR SOURCE AMBIENT or PREHEAT
39 COMBUSTION AIR TEMPERATURE at BURNER °C40 COMBUSTION AIR RELATIVE HUMIDITY %41 MAXIMUM AVAILABLE DRAFT at BURNER mm w.c.42 HEATER DRAFT TYPE FORCED or NATURAL or INDUCED
43 BURNER AIR PRESSURE DROP at DESIGN HEAT RELEASE mm w.c.44 BURNER AIR PRESSURE DROP at NORMAL HEAT RELEASE mm w.c.45 BURNER AIR PRESSURE DROP at MINIMUM HEAT RELEASE mm w.c.46 HEATER ELEVATION ABOVE SEA LEVEL m47 FLAME LENGTH at DESIGN HEAT RELEASE m48 FLAME WIDTH or DIAMETER at DESIGN HEAT RELEASE mm
API STANDARD 560 and
document.xls Metric Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
0 0
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 REVISED: August, 2003 0 30-Dec-99 2 of 3
GAS FUEL CHARACTERISTICS REV49 FUEL GAS DESIGNATION50 HEATING VALUE * [LHV]51 SPECIFIC GRAVITY [AIR = 1.0]52 MOLECULAR WEIGHT53 FUEL TEMPERATURE at BURNER °C54 FUEL PRESSURE AVAILABLE at BURNER55 FUEL GAS COMPOSITION Volume%56 Methane57 Ethane58 Propane59 Butane60 Pentane61 Hexane plus62 Cyclopentane63 Cyclohexane64 Ethylene65 Propene66 Butene67 Pentene68 Butadiene69 Carbon Dioxide70 Water71 Oxygen72 Nitrogen73 Sulfur Dioxide74 Hydrogen Sulfide75 Carbon Monoxide (CO)76 Ammonia77 Hydrogen78 Argon (Ar)79 Acetylene80 Benzene81 TOTAL 0.0 0.0 0.0 0.0 0.0
LIQUID FUEL CHARACTERISTICS82 FUEL OIL DESIGNATION83 HEATING VALUE * [LHV] kcal/kg84 SPECIFIC GRAVITY85 HYDROGEN to CARBON RATIO [BY WEIGHT]86 VISCOSITY [POINT 1] at °C cp87 VISCOSITY [POINT 2] at °C cp88 DISTILLATION : ASTM INITIAL BOILING POINT °C89 ASTM MID-POINT °C90 ASTM END POINT °C91 FUEL TEMPERATURE at BURNER °C92 FUEL PRESSURE AVAILABLE at BURNER93 ATOMIZING MEDIUM AIR or STEAM or MECHANICAL or GAS94 ATOMIZING MEDIUM TEMPERATURE at BURNER °C95 ATOMIZING MEDIUM PRESSURE at BURNER96 FUEL OIL METALS: Vanadium, Potassium, Sodium, Nickel97 FUEL OIL COMPOSITION Weight%98 Carbon (C)99 Hydrogen (H)100 Oxygen (O)101 Fixed Nitrogen (N)102 Sulfur (S)103 Ash104 Water105 TOTAL 0.0 0.0 0.0 0.0 0.0
API STANDARD 560 and
kcal/Nm3
kg/cm2
(CH4) (C2H6)(C3H8)(C4H10)(C5H12)(C6 +)(C5H10)(C6H12)(C2H4)(C3H6)(C4H8)(C5H10)(C4H6)(CO2)(H2O)(O2)(N2)(SO2)(H2S)
(NH3)(H2)
(C2H2)(C6H6)
kg/cm2
kg/cm2
mg/Nm3
(H2O)
document.xls Metric Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
0
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 #REF! 0 30-Dec-99 3 of 3
EMISSION REQUIREMENTS REV
159 HEATER EQUIPMENT NUMBER 0 0 0 0160 BURNER MODEL NUMBER 0 0 0 0 0161 FIREBOX BRIDGEWALL TEMPERATURE °C162 FIREBOX TEMPERATURE AT BURNER LOCATION °C163 FIREBOX TEMPERATURE DETERMINATION MEASURED or ESTIMATED
164 NOx * [LHV]165 CO * [LHV]166 UHC * [LHV]167 PARTICULATE * [LHV]168 SOx * [LHV]169
170 NOISE THRESHOLD SPECIFICATION dBA at 1 m
SPECIFICATION OPTIONS171 PRESSURE TAP REQUIRED YES or NO
172 SPECIAL GAUGES Specify173 SPECIAL VALVES Specify
174 SPECIAL HOSES Specify
175 FLANGED FUEL CONNECTIONS YES or NO176 ENGINEERING UNITS on DRAWINGS ENGLISH or METRIC or S.I.
177 POSITIVE MATERIAL IDENTIFICATION [PMI] REQUIRED YES or NO
178 MILL CERTIFICATIONS REQUIRED YES or NO
179 BURNER PERFORMANCE TEST REQUIRED YES or NO
180
NOTES AND COMMENTS181182183184185186187188189190191192193194195196197198199200201202203204205206207208209
210
API STANDARD 560 and
mg/Nm3
mg/Nm3
mg/Nm3
mg/Nm3
mg/Nm3
*CORRECTED TO 3% O2 [DRY BASIS at DESIGN HEAT RELEASE]
document.xls S.I. Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 REVISED: August, 2003 12/30/1899 30-Dec-99 1 of 3
PURCHASER: JOB NUMBER:
OWNER: LOCATION:HEATER GENERAL DATA REV
1 HEATER EQUIPMENT NUMBER
2 HEATER SERVICE
3 HEATER MANUFACTURER
4 TYPE OF HEATER VC [Vertical Cylindrical] or BOX or CABIN
5 SETTING REFRACTORY THICKNESS mm6 HEATER CASING THICKNESS mm7 FIREBOX INTERIOR HEIGHT from FLOOR TO ARCH mm8 FIREBOX INTERIOR LENGTH from WALL TO WALL mm9 FIREBOX WIDTH between TUBES CENTERLINE TO CENTERLINE mm10 TUBE CIRCLE DIAMETER [VERTICAL CYLINDRICAL HEATER] mm11 COMBUSTION AIR PLENUM COMMON or INDIVIDUAL
BURNER DATA12 TYPE OF BURNER STANDARD or LOW NOx or B.A.C.T.13 BURNER PROJECT CLASSIFICATION NEW or REPLACE or RETROFIT
14 BURNER MODEL NUMBER
15 QUANTITY of BURNERS REQUIRED (TOTAL FOR TWO FURANCES)
16 FIRING ORIENTATION UPFIRED or DOWNFIRED or HORIZONTAL
17 BURNER INSTALLED LOCATION ROOF or FLOOR or WALL18 BURNER CENTERLINE TO TUBE CENTERLINE mm19 BURNER CENTERLINE TO ADJACENT BURNER CENTERLINE mm20 BURNER CENTERLINE TO UNSHIELDED REFRACTORY mm21 BURNER CIRCLE DIAMETER [VERTICAL CYLINDRICAL HEATER] mm22 PILOT REQUIRED? YES or NO
23 PILOT MODEL
24 PILOT IGNITION METHOD
25 FLAME ROD YES or NO
26 PILOT FUEL
27 FUEL PRESSURE at PILOT psig25 PILOT HEAT RELEASE Btu/hr26 PILOT CONNECTION 1/2" FNPT or 1/2" R.F.27 PILOT IGNITION TRANSFORMER VOLTAGE 120VAC or 220VAC
28 PILOT IGNITION TRANSFORMER HOUSING NEMA 4 or NEMA 7
OPERATING DATA29 BURNER FUEL TYPE GAS or OIL or GAS & OIL
30 HEATER MAXIMUM HEAT RELEASE * [LHV] MW31 DESIGN HEAT RELEASE per BURNER * [LHV] MW32 NORMAL NAPHTHA CASE * [LHV] MW33 NORMAL HGO CASE * [LHV] MW34 MINIMUM HEAT RELEASE per BURNER * [LHV] MW35 OTHER CONDITION: MW36 BURNER TURNDOWN REQUIRED
37 EXCESS AIR at DESIGN HEAT RELEASE %38 COMBUSTION AIR SOURCE AMBIENT or PREHEAT
39 COMBUSTION AIR TEMPERATURE at BURNER °C40 COMBUSTION AIR RELATIVE HUMIDITY %41 MAXIMUM AVAILABLE DRAFT at BURNER mbar(g)42 HEATER DRAFT TYPE FORCED or NATURAL or INDUCED
43 BURNER AIR PRESSURE DROP at DESIGN HEAT RELEASE mbar(g)44 BURNER AIR PRESSURE DROP at NORMAL HEAT RELEASE mbar(g)45 BURNER AIR PRESSURE DROP at MINIMUM HEAT RELEASE mbar(g)46 HEATER ELEVATION ABOVE SEA LEVEL m47 FLAME LENGTH at DESIGN HEAT RELEASE m48 FLAME WIDTH or DIAMETER at DESIGN HEAT RELEASE mm
API STANDARD 560 and
document.xls S.I. Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
0 0
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 0 30-Dec-99 2 of 3
GAS FUEL CHARACTERISTICS REV49 FUEL GAS DESIGNATION50 HEATING VALUE * [LHV] kJ/kg51 SPECIFIC GRAVITY [AIR = 1.0]52 MOLECULAR WEIGHT53 FUEL TEMPERATURE at BURNER °C54 FUEL PRESSURE AVAILABLE at BURNER kPa55 FUEL GAS COMPOSITION Volume%56 Methane57 Ethane58 Propane59 Butane60 Pentane61 Hexane plus62 Cyclopentane63 Cyclohexane64 Ethylene65 Propene66 Butene67 Pentene68 Butadiene69 Carbon Dioxide70 Water71 Oxygen72 Nitrogen73 Sulfur Dioxide74 Hydrogen Sulfide75 Carbon Monoxide (CO)76 Ammonia77 Hydrogen78 Argon (Ar)79 Acetylene80 Benzene81 TOTAL 0.0 0.0 0.0 0.0 0.0
LIQUID FUEL CHARACTERISTICS82 FUEL OIL DESIGNATION83 HEATING VALUE * [LHV] kJ/kg84 SPECIFIC GRAVITY85 HYDROGEN to CARBON RATIO [BY WEIGHT]86 VISCOSITY [POINT 1] at °C cp87 VISCOSITY [POINT 2] at °C cp88 DISTILLATION : ASTM INITIAL BOILING POINT °C89 ASTM MID-POINT °C90 ASTM END POINT °C91 FUEL TEMPERATURE at BURNER °C92 FUEL PRESSURE AVAILABLE at BURNER kPa93 ATOMIZING MEDIUM AIR or STEAM or MECHANICAL or GAS94 ATOMIZING MEDIUM TEMPERATURE at BURNER °C95 ATOMIZING MEDIUM PRESSURE at BURNER kPa96 FUEL OIL METALS: Vanadium, Potassium, Sodium, Nickel97 FUEL OIL COMPOSITION Weight%98 Carbon (C)99 Hydrogen (H)100 Oxygen (O)101 Fixed Nitrogen (N)102 Sulfur (S)103 Ash104 Water105 TOTAL 0.0 0.0 0.0 0.0 0.0
API STANDARD 560 and
(CH4) (C2H6)(C3H8)(C4H10)(C5H12)(C6 +)(C5H10)(C6H12)(C2H4)(C3H6)(C4H8)(C5H10)(C4H6)(CO2)(H2O)(O2)(N2)(SO2)(H2S)
(NH3)(H2)
(C2H2)(C6H6)
mg/Nm3
(H2O)
document.xls S.I. Units04/22/2023
BURNER SPECIFICATION JOHN ZINK FILE NUMBER: PROJECT NUMBER:
0 0
ADAPTED FROM: REVISION: DATE: SHEETAPI RECOMMENDED PRACTICE 535 0 30-Dec-99 3 of 3
EMISSION REQUIREMENTS REV
159 HEATER EQUIPMENT NUMBER 0 0 0 0 0160 BURNER MODEL NUMBER 0 0 0161 FIREBOX BRIDGEWALL TEMPERATURE °C162 FIREBOX TEMPERATURE AT BURNER LOCATION °C163 FIREBOX TEMPERATURE DETERMINATION MEASURED or ESTIMATED
164 NOx * [LHV] mg/Nm3165 CO * [LHV] mg/Nm3166 DUST * [LHV] mg/Nm3167 PARTICULATE * [LHV] mg/Nm3168 SOx * [LHV] mg/Nm3169
170 NOISE THRESHOLD SPECIFICATION dBA at 1 m
SPECIFICATION OPTIONS171 PRESSURE TAP REQUIRED YES or NO
172 SPECIAL GAUGES Specify173 SPECIAL VALVES Specify
174 SPECIAL HOSES Specify
175 FLANGED FUEL CONNECTIONS YES or NO176 ENGINEERING UNITS on DRAWINGS ENGLISH or METRIC or S.I.
177 POSITIVE MATERIAL IDENTIFICATION [PMI] REQUIRED YES or NO
178 MILL CERTIFICATIONS REQUIRED YES or NO
179 BURNER PERFORMANCE TEST REQUIRED YES or NO
180
NOTES AND COMMENTS181182183184185186187188189190191192193194195196197198199200201202203204205206207208209
210
API STANDARD 560 and
*CORRECTED TO 3% O2 [DRY BASIS at DESIGN HEAT RELEASE]
