CRANE-DEMING VERTICAL IN-LINE INDUSTRIALBULLETIN 3180 SECTION 38

ease of installation& maintenance

Install like a valveMount in the pipelineSupport on pipe orfoundation. . . Savespace - save time

1

STANDARD MOTORSSELF-ALIGNING SHAFTPULL-OUT MAINTENANCEENCLOSED IMPELLER

Crane-Deming offers you abroad line of industrial processpumps of the proven cost savingin-line design. these versatilepumps efficiently handle a widerange of corrosive and non-corrosive liquids from water tohydrocarbons. You can applythem with confidence.

FIG. 3180 SeriesSingle-stage centrifugal

Industrial Process PumpsCapacities to 1000 gpmHeads to 400 ft.Temperatures to 350°FPressures to 350 psig

METALLURGYPump liquid ends are available in anymechanable metal. Your Crane repre-sentative will assist you in selection ofproper metallurgy. Available alloysinclude:

Ductile (Nodular) ironBronzeCast SteelMartensitic chrome steelAustenitic stainless steelHigh alloy stainlessNickel alloys

standard construction2

PROTECTED SHAFTOne-piece shaft assures sustained positivealignment of complete pump-motor rotatingelement, eliminates couplings, minimizesshsaft deflection. Shaft sleeve hook-typefree to expand with temperature variation,extends through gland. Sleeve keyed toshaft. Shaft is isolated from contact withliquid by sleeve and Teflon® O-ring and flatgaskets.

MOTOR-STANDARD C-FLANGE

VAA-E, VAB-E,VA05-E, VA10-E,VA50-E, VA60-E,VA70-ECONSTRUCTION

1 Casing2 Impeller7 Casing Wear Ring 26 Impeller Screw 40 Deflector 212 Cap Screw 264 Pipe Plug8 Impeller Wear Rings (opt) 27 Packing Box Wear Ring 71 Adapter 216 Pipe Screw 270 Impeller Washer11 Packing Box Cover 29 Lantern Ring 73 Casing Gasket 219 Cap Screw 272 Impeller Screw-O-Ring13 Packing 30 Impeller Washer Gasket 206 Split Gland Clip 228 Motor 281 Gland Stud14 Shaft Sleeve 32 Impeller Key 208 Pipe Plug 239 Stud 287 Jack Screw17 Split Gland 38 Shaft Gasket 210 Hex Nut 249 Hex Nut 297 Pipe Plug

VA20-E, VA30-E,VA40-E, VA80-E,CONSTRUCTION

outstanding featuresTYPICAL SEAL ARRANGEMENTS

PACKING BOX COVERUnique through-bolt design reduces stress onadapter attachment. Replaceable wear ringstandard. Jacketed type optional.Fully machined for mechanical seals or packing.Packed box has 2-bolt plaion or quench gland andin-out connections to lantern ring. Sealed box has4-bolt seal flanges with full 360 degree register fitprotected by confined gasket.Optional sealing variations include single, double,balanced and unbalanced inside seals, throat andthrottle bushings, and connections for flushing,cooling, venting, quenching or lubrication. YourCrane representative will recommend sealingsystems for your application.

DUAL PURPOSE JACK SCREWS

CASINGIMPELLER

TOP PULL-OUTSIMPLIFIES

MAINTENANCE

CRANE* Type 9T CRANE* Type 9BT*Crane Packing Co.

DURA* Type CRO*Durametallic Corp.

DURA* Type ROTT

SUCTION SIDE BALANCE SIDE

ASSEMBLED DISASSEMBLED

3

Built-in Jack screws simplify removal andprotect mechanical seal during disassem-bly. Packing box cover held securely inplace on adapter after pull-out.

Flanged suction and discharge on common centerline.Integral one-piece unit suitable for in-line or pedestal mount-ing. Desgined for working pressures to 350 PSI with 1/

8”

corrosion allowance. Replaceable wear ring standard.Selfventing. Case drain gasketed or tapered thread.Flanges flat-faced ASA 150 lb.standard, 300 lb. optional.

Fully enclosed, balanced, one-piece design. Balancechamber provides safe, control of stuffing box pressure,and limits axial thrust for long bearing life. Replaceablewear rings assure high sustained efficiency. Flow pas-sages contoured forlow NPSH requirement. Adjustmentnot required. Key to shaft.

Complete rotating assembly easilyremoved for inspection without disturb-ing piping. Full circle register protectedby CONFINED GASKET assurespermanent alignment.

wideapplicationVersatile Crane-Deming In-Linepumps are designed for use in abroad range of industries andapplications:

- Chemical- Petrochemical Petroleum Coal- Fiber- Pulp and Paper- Food and Beverage- Pharmaceutical Fats and Oils- Soap- Paint- Automotive- Primary Metal- Rubber- Metal- Fabrication- Utilty

Wherever fluid is moved . . .“Bring the Pump to the pipinginstead of piping to the pump” . . .save time and lower costs with theCrane-Deming In-Line industrialprocess pump.

Crane-Deming In-Line circulates water where the pipe is. Comparethis mounting with cost of floor mounted horizontal pumps.

Crane-Deming In-Line pump handling petroleum. Note simple pipesupports for piping and pump.

Crane-Deming In-Line pump at a gasoline tank farm. Note use of asingle block foundation supporting pump and piping. Simplified In-Line installation saves fittings, lowers installation costs.

DEMING PUMPS

dimensions

PUMP DATA

‡Can be rotated in increments of 90°Flange thinkness per ASA standard B16.5, flat face

*5 1/16 on 3182

performance

DESIGNATION-INCHES:Suction x Discharge x Impeller Diameter (maximum)

VAA-E 11/2 x 1 x 6 VA05-E 2 x 1 x 91/2 VA20-E 3 x 11/2 x 12

VAB-E 3 x 11/2 x 6 VA50-E 3 x 11/2 x 91/2 VA30-E 3 x 2 x 12

VA60-E 3 x 11/2 x 91/2 VA40-E 4 x 3 x 12

VAIO-E 3 x 2 x 71/2 VA70-E 4 x 3 x 91/2 x VA80-E 6 x 4 x 12

interchangeability typical standard materialsof construction

1-15 HPVAA-E, VAB-E, VA05-EVA10-E, VA20-E, VA30-EVA50-E, VA60-E, VA70-E

71/2-60 HPVA05-E, VA10-E, VA20-EVA30-E, VA40-E, VA50-EVA60-E, VA70-E, VA80-E

60-100 HPVA60-E, VA70-E

Maximum interchangeability of components intheFigure 3180 Series assures maintenance and re-duced inventory requirements. The eleven casingsand impellers may be grouped into any of the motorsize ranges shown above. Wiothin each group, theshaft sleeve and mechanical seal components areindentical. Packing box covers are held to an abso-lute minimum: three for Fig. 3182, two for Fig. 3185,and one for Fig. 3186

ITEM PART NAME PART MATERIAL1 Casing CI, DI, CS, 316, 347, A-20, 8 BZ,

Hast C, Monel2 Impeller 8, BZ, CI, 316, 347, A-20, Monel7 Casing Wear Ring 5 BZ, CI, 316, 347, A-20, Hast C,

Monel8 Imp. Wear Ring 8 BZ, CI, 316,347, A-20, Monel11 Packing Box Cover CI, DI, Steel, 316, 347, A-20,

Hast C, Monel*13 Packing Graphite Asbestos, teflon Impreg-

nated White Asbestos14 Shaft Sleeve 416, 316, C-20, 5 BZ, Hast C, Monel*17 Split Gland CI, 316, A-20, 5 BZ, Hast C, Monel26 Impeller Screw 316, A-20, 316, Hast C, Monel27 Balance Wear Ring 5 BZ, CI, 316, 347, A-20, Monel*29 Lantern Ring Teflon30 Imp. Nut Gasket Teflon32 Impeller Key Steel38 Shaft Gasket Teflon40 Deflector Neoprene65 Mechanical Seal71 Adapter CI73 Casing Gasket African Blue Asbestos206 Split Gland Clip 316208 Pipe Plug MI, 316, 347, A-20, Hast C, Monel210 Hex Nut 316, C-20212 Cap Screw CS, 304216 Pipe Plug MI, 316, A-20, Hast C, Monel219 Cap Screw Steel239 Stud CS,316249 Hex Nut CS, 316264 Pipe Plug MI, 316, A-20, Brass, Hast. C, Monel270 Impeller Washer 316, A-20, Brass, Hast. C, Monel272 O-Ring Teflon Coated Buna-N281 Gland Stud 316, C-20

D I Cast Ductile Iron�ASTM A395-61 60-45-15C I Cast Iron � ASTM A 48-56C S Cast Carbon Steel ASTM A216-WCB1045-C Wrought Carbon Steel SAF 1045-C8BZ Cast Bronze - ASTM A216-WCB5BZ Cast Bronze - ASTM B144-61416 Wrought Stainless Steel 4151 Type 416316 Cast Stainless Steel ACI CF-8M316 Wrought Stainless Steel 4151 Type 316304 Wrought Stainless Steel 4151 Type 304A-20 Cast Stainless Steel Ad CN-7MC-20 Wrought Stainless Steel Carpenter 20Monel Cast Monel Federal Spec. QQ-N-288Monel Wrought Monel ASTM 8164-61Nickel Cast NickelNickel Wrought Nickel ASTM B160-61HAST.- B Cast Hastelloy B ASTM B 332-58THAST.- B Wrought Hastelloy B ASTM B 335-58THAST.- C Cast Hastelloy C ASTM B 332-58THAST.- C Wrought Hastelloy C ASTM B 336-58T

MATERIAL SPECIFICATIONS

Fig. 3182

Fig. 3185

Fig. 3186

DEMING® PUMPS