Built-Up Pocket Door Frames - A & F Wood · Built-Up Pocket Door Frames 1750 Series For 1 1/8˝ to...
Transcript of Built-Up Pocket Door Frames - A & F Wood · Built-Up Pocket Door Frames 1750 Series For 1 1/8˝ to...
Built-Up Pocket Door Frames1750 SeriesFor 1 1/8˝ to 1 3/8˝ DoorsMaximum Door Weight 150 lbs.
Pocket Door FramesOpen up rooms, creates more space and provides privacy. You can doit all with A&F Wood Produtcs Pocket Door Frames. Where a ˝tradi-tional swinging˝ door would use up too much space, pocket doors fitright in to solve room planning problems. You get more usable space,more flexibility and better appearance. Installation is approximately 20minutes, using just a few basic tools.
Pocket Door HardwareA&F Wood Products offers a snap-in track and hanger system. Largerwheels and heavier gauge steel body design. *Four wheel ball bearinghardware is available to hold up to 250 lbs.
Pocket Door OptionsMiscellaneous options are available to customize your Pocket DoorFrames. You can order separately Mullion Kits, Extension Kits, JambKits and more. Stock is available in 4/0 widths, 7/0 & 8/0 heights aswell as options for 2x6 walls, 5/8˝ drywall, and 13/4˝ doors.
Built-Up FramesFully assembled for quick and easy installation. All frames are designedto hold up to 150 lbs. for a standard 6´8˝ door.
040105 PF101
K.D. Pocket Door Frames2000 SeriesFor 1 1/8˝ to 1 3/8˝ DoorsMaximum Door Weight 150 lbs.
Pocket Door FramesOpen up rooms, creates more space and provides privacy. You can doit all with A&F Wood Produtcs Pocket Door Frames. Where a ˝tradi-tional˝ door would use up too much space, pocket doors fit right in tosolve room planning problems. You ge more usable space, more flexi-bility and better appearance. Installation is approximately 20 minutes,using just a few basic tools.
Pocket Door HardwareA&F Wood Products offers a snap-in track and hanger system. Largerwheels and heavier gauge steel body design. *Four wheel ball bearinghardware is available to hold up to 250 lbs.
Pocket Door OptionsMiscellaneous options are available to customize your Pocket DoorFrames. You can order separately Mullion Kits, Extension Kits, JambKits and more. Stock is available in 4/0 widths, 7/0 & 8/0 heights aswell as options for 2x6 walls, 5/8˝ drywall, and 13/4˝ doors.
K.D. FramesOne size fits all up to 3/0´s, Knock Down Frames you can cut to size for your customizeopening. Each K.D. is designed to hold 150 lbs. standard 6´8˝ door.
040105 PF102
Built-Up Pockets150 lb. & 250 lb. Pocket DoorHardware Specifications
• For installation of pocket or bi-parting doors up to 4´ wide, 1˝ to 1-3/8˝thick panels weighing up to 150 lbs. each and up to 8´ high.
• Heavy gauge, steel stiffener reinforces split jambs.• Four large 1˝ wheels for easy rolling action.• Easy to install feature makes installation a ˝snap˝ .• Supports panels weighing up to 150 lbs.• Easy adjustment after installation.• V-groove jump proof aluminum track.• Opening width equals door width multiplied by 2, add 2˝.• For Bi Part: Sum of 2 doors multiplied by 2, add 2”.• For 6´8˝ Door: Height equals 84” from finished floor.• For 7´0˝ Door: Height equals 88” from finished floor.• For 8´0˝ Door: Height equals 100” from finished floor.• Built-Ups can be ordered in 6´8˝, 7´8˝, or 8´0˝ door height.• PDFC150N conforms to ANSI A156.14 type D8681• Cross Reference: Stanley 1750, Cox 15-200, Grant 7000 Series,
Hager 9601/9701, Johnson 100, Lawrence 506/580 Track, Sterling 1601 Series.• 250 lb. heavy duty hardware has four large 1˝ ball bearing wheels for easy rolling action.• Support panels weighing up to 250 lbs.
Complete Set:One set consists of: 1 Track, 1 pair of Hangers, 2 Guides, 1 Bumper and 1 Wrench.
WRENCH1 - 1750Wrench
SPLIT FLOOR GUIDE1 - Splitfloorguide
BUMPER1 - 1750Bumper(already attachedon Built-Up)
HANGER2 - 1750HDW
TRACK1 - 1750Track
040105 PF103
• For installation of pocket or bi-parting doors up to 3˝ width, weighing up to150 lbs. each and up to 8´ high
• Heavy gauge, wrap around steel stiffener reinforces split jambs• Four large 1˝ wheels for easy rolling action• Easy-to-install feature makes installation a “snap”• Supports panels weighing up to 150 lbs.• Cut marks on header make for easy sizing• Easy adjustment after installation• Cut marks on header make for easy sizing• Non-handed steel header brackets for easy leveling of header assembly• V-Groove jump proof aluminum track• Opening width equals door width multiplied by 2, add 1 1/4˝• For Bi Part: Sum of 2 doors multiplied by 2, add 1/4˝• Kits are sized for 3´0˝ door width and can be cut shorter at installation• For 6´8˝ Door: Height equals 84 1/2˝ from finished floor• For 7´0˝ Door: Height equals 88 1/2˝ from finished floor• For 8´0˝ Door: Height equals 100 1/2˝ from finished floor• Kits are sized for 6´8˝, 7´0˝, or 8´0˝ door height and can be cut shorter at installation• PDFC150N conforms to ANSI A156.14 type D8671 Cross Reference:
Stanley 735/40-3925R/40-3940, Crowder Crowderframe, Hager 9630/9631,Johnson 1500, Sterling 1630
• 250 lb. heavy duty hardware has four large 1˝ ball bearing wheels for easy rolling action.• Supports panels weighing up to 250 lbs.
Complete Set:One set consists of: 1 Header Track, 2 Floor Plates, 1 Wrench, 2 Guides, 1 End Bracket, 1 Bumper, 1 Hanger, 2 Jamb Studs
HEADER TRACK1 - Header
HANGER2 - 1750HDW
SPLIT FLOOR GUIDE1 - Splitfloorguide
BUMPER1 - 1750Bumper
WRENCH1 - 1750Wrench
FLOOR PLATE2 - Floorplate END BRACKET
2 - Bracket
JAMB STUDS1 - Jamb
K.D. Pockets150 lb. & 250 lb. K.D. Pocket Door Specifications
040105 PF104
Converging Door Kit/Mullion ConnectorInstructionsFor Joining two #1750 Buil-Up Pockets ortwo #2000 Series K.D. Pocket Door Frames
Step 1: Prepare Rough Opening:• Built-Up: 4 x Door + 2˝Sample: 30˝ Door x 4 + 2˝ = 122”
• K.D.: 4 x Door + 1/4˝Sample: 30˝ Door x 4 + 1/4˝ = 120 1/4˝
Step 2: • Built-Up: Cut 3/4˝ off opening end of header assembly, cutends square to keep header straight.
• K.D.: Cut 1˝ off opening end of header assembly,cut ends square to keep header straight.
Step 3:Butt cut ends together and fasten using brackets in this kitas illustrated. Drill 1/4˝ holes for the 2 machine bolts and onein the center for lag screw.
Step 4:Hang combined assembly and fasten to rough header withcenter lag screw. Adjust to level.
Step 5:Install center stop bumper into ends of track.Final adjust after doors are in place.
Step 6:Continue to install doors per instructions with Pocket door Frame.
KD 1” Built-Up3/4”
040105 PF105
Jamb Kit InstructionsFits all Built-Up and K.D. Pocket Door Frames
#1755 Clear Pine Jamb Kit#1756 Paint Grade Pine Jamb Kit
Pre-sanded jamb kits are available in stain or paint grade pine. Simply, cut tolength and install. Jamb kits fit all standard 2x4 wall applications with 6´8˝doors.
Installation Instructions:1. Install Pocket Door Frame
according to instructions. Once
drywall is installed around unit,
measure height “A” (from floor to
bottom of frame header).
2. Open door fully so door is
extended into opening. Cut split
jambs to “B”. Fasten to front edge
of frame. Maintain minimum
3/16˝ clearance on both sides of
door. Raise or lower hanger to
plumb door with split jambs.
3. Shim and plumb strinke jamb
(wide piece) with door.
4. Cut split headers to “C”.
Determine side of hangers with lock
arm and fasten this header with
screws for easy removal. Nail other
side. Maintain 3/16˝ on each side of
door.
5. Fasten bottom door guides so
door stays in center of pocket and
travels easily without bindings.
6. Finish with your choice of casings
(not included).
040105 PF105A
Extention Kit #1752 & #1753 InstructionsBuilt-Up Pocket Door FrameFits all Built-Up Pocket Door Frames
Installation Instructions
Step 1:
Prepare Rough Opening (Special Dimensions)
Nominal DoorSize Equation A R.O.7´0˝ Door + 4” = 88˝8´0˝ Door + 4” = 100˝
Step 2:
Slip back extension over the top of the basket back.Then screw into basket on both sides of back with#6 x 1˝ screws.
Step 3:
Slip split jamb extension on the top of the basket split jamb.Steel on top of basket will fit under 4˝ split jamb material.While aligning and butting wood together, screw directly into steeland wood from the back side with #6 x 2˝ screws.
Step 4:Continue with Step 2 on pocket instructions.
040105 PF106
Extention Kit #752, #753 & #754 InstructionsK.D. Pocket Door FramesFits all K.D. Pocket Door Frames
Installation Instructions
Step 1:Prepare Rough Opening (Special Dimensions)
Nominal DoorSize Equation A R.O.7´0˝ Door + 4 1/2” = 88 1/2˝8´0˝ Door + 4 1/2” = 100 1/2˝9´0˝ Door + 41/2” = 112 1/2˝
Step 2: Prepare Split Members:Push wood filler out of steel split member 8˝.(Split members supplied in pocket door frame.)Cut wood off flush with steel.(Repeat on remaining split members. Four per pocket.)
Step 3:Install Extenders:At opposite end of cut, insert extenders.
Step 4:Continue with pocket frame installationInstructions.
040105 PF107
040105 PF108
040105 PF109
Step 3. Knock the wall studs out ofplace with a 3-lb. Maul. The nailswill bend when you hit the studs.Remove the floor plate too.
040105 PF110
2000 K.D. Pocket Door Frame Assembly and Installation InstructionsFor any 2’0” – 3’0” Doors weighing up to 150 lbs.
We Supply:
1 – Header and Track Assembly4 – Jamb Stiffeners2 – Floor Brackets1 – Snap-in Door Plates1 – Snap-in Hangers1 – Bumper1 – Wrench
Fasteners 12 – 1 _” (3.81 cm) Screws 2 – 1” (2.54 cm) Screws
3 – 5/8” (1.59 cm) Screw 18 – 2” (5.08cm) Nails
Bi-parting Bracket applications requiresA 741 bi-parting bracket (not included)
These frames will accommodate the following doors
6/8 (203.2 cm) 2’0” – 3’0” (60.9 – 91.4 cm) 150 lb (68 kg)7/0 (213.4 cm) 2’0” – 3’0” (60.9 – 91.4 cm) 150 lb (68 kg)8/0 (243.8 cm) 2’0” – 3’0”(60.9 – 91.4 cm) 150 lb (68 kg)
Step 1: Prepare roughopening.
Finish Floor to Rough Headerheight should be minimum of (A)see Table and Figure 1.Determine width of rough openingby multiplying door width by 2 andadding 1-1/4” (31.8 mm).Example: For a 30” 76.20cm) wide
door, the rough door opening width is (30” x2) + 1-1/4”= 61-1/4”.(66.20cm x 2) + 31.8 mm = 155.58 cm).
Door A A B Bi-parting Bracket
6’8” 84-1/2” (214.6 cm) 83-1/2” (212.1 cm) 80-1/8” (203.5 cm)
7’0” 88-1/2” (224.8 cm) 87-1/2” (222.3 cm) 84-1/8” (213.7 cm)
8’0” 100-1/2” (255.3 cm) 99-1/2” (252.7 cm) 96-1/8” (244.2 cm)
Step 2: Cut Header Assembly
The header assembly does not requirecutting if your Door panelwidth is 36” (91 cm). For shorter widths,cut Header assemblyas follows.
1. size indicators. If your Door dose not correspond withpre-marked sizes (go to Step 3).
2. Cut Track 2” shorter than Header to allow for end Bracket.
NOTE: Header assembly pre-marked Door width.Header markings accommodate inside Trim of Pocket.
Step 3: For Odd Size Doors
A. Cut the nailing strips to the size of the door panel width plus7/8” (2.22 cm). Cut and remove excess strip “X” from themiddle of the assembly, not from the end.
B. At the other end, cut header “Y” to remove twice the amount “X” in step “A”. Cut the track 2” (5.08 cm) shorter than theheader.
Example: For a 26” (66.04 cm) doorNailing Strip is cut to 26-7/8” (68.25cm)Excess Nailing Strip “X” is 9-1/8” (23.18 cm)Excess Header “Y” is 18-1/4” (46.36cm)Cut Track 2” (5.08 cm) shorter
Step 4: Install End Bracket
Use 2 – 5/8” (1.6 cm) screws
Step 5: Install Header
Determine width of Door. Cut Nailing Strip at the premarked
040105 PF111
Step 6: Level the Header Assemblyat the correct height and nail End Bracket toJamb
Step 7: Install Floor Brackets on the one side of Jamb.
Ensure wood is exposed as illustrated
Use 4 - 1-1/2” (d.81 cm) screws
Step 8: Install Split Jamb and StudStand up split Jamb so it butts against nailingstrip, with exposed wood side facing out ondrywall side. Tack the top, plumb the Jamb,and then screw Bracket to the floor. Takeremaining Split Jamb, slide onto the Floor
Bracket prongs and nail to opposite side of header assembly. Repeatprocedure for split stud positioning it in the middle pocket.
Note: Split Jambs are manufactured with a slight bow.
Step 9: Install Bumper
Screw the Bumper to the rough Jamb at the backof pocket with 5/8” screw (1.6 cm) approximately102 cm (40”) from floor. Shim it out, if necessary,so that the front edge of Door will be flush withfront edge of nylon Door guide.
Step 10: Install Temporary Brace (Optional)Insert 1” (25mm) x 2-1/8” (54 mm) boardthrough split Jamb and Stud as shown.Rest the board on top of the Bumper. Thennail a support leg to board as shown. (Thisprovides added stiffness while wallmaterial is being applied). This board willbe removed prior to installing Door. The
pocket may now be enclosed by applying wall sheathing, drywall,paneling, etc. as desired.
Step 11: Install Hangers
Fasten the Hanger Plates on the top of the doorpanel. Hangers must be 7/8” (2.22 cm) in fromthe side edge, as shown
Use 8 – 1 _” (3.81 cm) screws
Step 12: Install Adjustable Bolt and Hangers
Slide both Wheel Hanger assemblies intoTrack from the exposed end.
Step 13: Install Door by Lifting and Snapping it in
Installation is accomplished by snapping oneDoor Hanger and then the other. To removedoor, activate tab in direction of white arrowwith a flute back screw driver as shown.
Step 14: Using the Wrench supplied,
turn the adjustment Post so that theDoor is Plumb and has proper floorclearance
Step 15: Install Door Guide
Fasten Door Guide to the split Jamb using 1”Screws with nylon guides projecting into theopening as shown.
Step 16: Install Face Jamb
The face jamb fits between the nailing strip andthe rough floor. Butt the face jamb underneaththe nailing strip and shim for plumb. Nail intoposition.
Step 17: Install Door Pull (Optional)
No Door Pulls are included in this kit,but you may choose from a varietyof Door Pulls and Latch sets which areavailable through your dealer.
Step 18: Install Door Trim
Install Door Stop Trim (as for a Hinged Door)allowing 3/16” (5 mm) clearance between Doorand Stops for possible Door warpage. Stopshould be installed over Door Guide. ApplyDoor casing Trim as you would other Doorinstallations.NOTE: For best performance of your Pocket
Door, the Track should not be painted. If you wish, a silicone lubricantmay be applied for even smoother operation.
A
Step 13: Install Door by Lifting and Snapping it in
Bifold Track & HardwareStandard 30 lbs.Specifications
30 lb. Bifold PanelsItem Size # of Panels Units Price
• For installation of 2 or 4, 7/8˝ to 1 3/8˝ thick panels weighing up to 30 lbs. each• Spring loaded top pivot and roller guide for easy installation• Durable pre-painted track• All metal components galvanized against corrosion• Permanently lubricated roller guide• Panel width equals known finished opening width divided by number of panels, less 1/4˝• Opening Width equals known finished panel width plus 1/4˝ multiplied by number of panels• Door Height equals 1 5/8˝ less than finished opening height• BF30, BLC30 conforms to ANSI A156.14 type D8622• Cross Reference: Stanley 2800/2900 Series, Cox 43/48, Crowder CF-100, Grant 2600 Series, Henderson B Series,
Johnson 1800, Sterling 9000
Standard grade bifold hardware system designed for li ghter weight doors. White pre-finished track to guide door throughopening. Use with top pivot brackets on door penel. The Bottom Pivot provides vertical adjustment of doors. Slips intojamb brack at floor level and can be moved horizontally. The Guide Wheel provides door movement on the track and isspring loaded. Snuggers holds the doors snug for two or four panel doors. The Jamb Bracket is moves easily for horizon-tal adjustments. The Almond Plastic knob is used on the tow or four panel doors. Is easily used to open and close doors.
2 Panel Complete Packaged Contractor SetsOur doors are pre-sized to fit in standard wood and metal openings.Example: 48˝ x 84˝ Opening = (4 – Panels @ 11 3/4˝ x 82 1/2˝)One set consists of: 1- Track, 1- Roller, 1- Top Pivot, 1 Pivot Lock,1-Botom Pivot , 1- Floor Pivot Bracket, 1 Non-Mortise Lift-off Hinge,1 four Door Aligner, Knob, Adjustment Wrench
Top Pivot Bottom Pivot Guide Wheel Plastic Knob
Snuggers Jamb Bracket Alligners
2 Door System 4 Door System
040105 PF112
Bifold Track & HardwareHeavy Duty - 75 lbs. Specifications
Surface Mounted Bifold hardware for 1-1/8˝ to 13/4˝ panels up to 75 lbs each panel
Commercial grade bifold hardware system designed for use with heavier than normal doors. Designed for 12˝ – 24˝ pan-els up to 9/0 high. Precision extruded commercial grade aluminum track features line-design fascia to hide finger marksand scratches or to hold paint if desired. Patented “tricycle” hangers with large nylon 1˝ diameter ball bearing wheels, ridesmoothly and quietly on convex shaped system facilitating easy mounting or dismount of door panels. Hangers areadjustable for height in case of settling. Floor bracket has an adjustable bottom pivot socket. System is supplied with non-mortise hinges that can be replaced with customer supplied mortise hinge. 14-16 gauge zinc dichromate plated steel parts.
2 Panel Complete Packaged Contractor Sets
Our doors are pre-sized to fit in standard wood and metal openings.
Example: 48˝ x 84˝ Opening = (4 – Panels @ 11 3/4˝ x 81˝)
2 Panel Complete Packaged Set 4 Panel Complete Packaged Set
2 Door System 4 Door System
040105 PF113
Bifold Door - 30 lbs.Assembly and Installation InstructionsFor Bifold 4 Panel Sets
Set Contains1-Track with Two Track Sockets2-Bottom Pivots2-Top Pivots2-Jamb Brackets2-Top Roller Guides1-Snugger2-Plastic Knobs6-Bifold Non-Mortis Hinges1-Set Door AlignersNecessary Fasteners*Track is less than opening to reduce need to cut track.
You SupplyDoor Panel(s) as specified on the package chart,Screwdriver, Tape Measure, Drill, Clamp, Hammer.
How to Install your Bifold DoorsPlease read the complete instructions carefully before you start installation.All instructions apply to any size of bifold door installation.The same instructions also apply to all type of door panels.
1. Door sizingHeight – Make doors 1 5/8˝ less than the net Opening height. Width – Divide netopening width by the number of Door panels (2 or 4) and subtract 1/4˝ to determine the netdoor panel width. For example: A 30˝ opening for a two door bifold requires door panelsthat are 14 3/4˝ wide. (30 ÷ 2 = 15 - 1/4 = 14 3/4˝). A 48” opening with 4 panels requires door panels that are11 3/4˝ wide (48 ÷ 4 = 12 - 1/4 = 11 3/4˝).
2. Install non-mortise hinges to edge of doors 1” or more in thickness. Place panels of foldingdoors side by side with a 5/16˝ spacer between the panels and clamp together. Locate hingesapproximately 6: from each end of doors and at their centers. The leaf position on the door isoptional. Using the hinge as a template drill 3/32˝ holes approximately 7/8˝
3. Drill 7/16˝ diameter holes 1 7/8˝ deep for pivots and guides on center and1˝ from the edge of door.
4. Locate the pivots and guide as shown. Tap parts into the holes with lighthammer blows directly on the top of the pins.
5. Cut Track. If necessary, cut track to at least 1/8˝ less than the widthof the finished opening. Use a fine tooth hack saw.
040105 PF114
Bifold Door - 30 lbs.Assembly and Installation Instructions (cont’d)6. Top pivot bracket in each end of track should have pivot hole
(A) closet to jamb. Fasten track to header. On two-door unit track should be firmly against jamb at guide end of track. Use track as template and mark screw locations. Drill 1/8˝ pilot holes to approximate length of screws.
7. Place jamb bracket so enter line is plumb with center line of track. Bottom leg should rest firmly on carpet or floor. To fasten jambbracket, drill 7/64˝ pilot holes to approximate length of screwsand apply fasteners.
8. To install hinged pair of doors, place pivot pin (B) in hole, lift doors(compressing pin spring) and seat bottom pin into jamb bracket slot. Compress wheel pin, swing door under track and release wheel into track channel.
9. Press self centering (4-dr) snugger into track between pairs of doors in4 panel installations, or press (2-dr.) snugger into track between guide
wheel and jamb in 2 panel installations.
10. Horizontal Adjustment: Use Phillips screw driver to reposition top pivot bracket © inor out. Lift hinged pair of doors slightly to clear slot in bottom jamb bracket, moveadjusting bolt in or out until doors are plumb with jamb, and reseat bolt in bracket slot.Adjust to obtain 1/8˝ gap between pairs of doors at center of opening (or doors and
jamb in 2-door opening). Vertical Adjustment: Lift doors again and rotate adjustingwheel (D) clockwise to raise doors, counterclockwise to lower them. Adjust doorsupwards for minimum clearance at the header. Reseat adjusting bolt in bracket slotbeing careful not to change horizontal positioning. Do not attempt to turn wheel with teeth engaged in the bracket.
11. To place knobs, drill 7/64˝ holes in center of guide doors about 36˝ from floor.
12. For 4-door installation only. Attach aligners to back of guide doors, 12˝ from floor.Adjust in or out in slatted holes until doors “snap” closed. Tighten screws.
Drill 7/64˝ pilot holes to a depth approximately the length of screws.
040105 PF115
Bifold Door - 75 lbs.Assembly and Instructions
How to Install your Bifold DoorsPlease read the complete instructions carefully before you start installation. Allinstructions apply to any size bifold door installation. The same instructions alsoapply to all type of door panels.
Prepare Opening Carefully: Make sure corners are square, header is level andjambs are straight.
1. Cut Track to fit Opening Width and fasten toheader jamb with 1-1/4˝ Pan Head Screws.Note: Insert Parts in Track Before Mounting
2. Fasten Hinges to Doors (1606). (A) Stand pivot door on edge and mark a line at 7˝from top of midpoint and 11˝ from the bottom. (B) Attach hinge half with pin atmarks (hinge pin pointing up) with 1˝ flat head screws. (Note: with nylon knuckle athinge flush against back side of door). (C) Place second door back-to-back against firstdoor with top of doors even. Slip hinge half without pin over hinge half with pin. (D)Attach hinge half without pin to door.
3. Fasten Pivot Plates totop and bottom ofdoors as shown. Note: 1121 nylon lock-ing arm must opentowards rear of opening.
4. Fasten 1011 Floor Bracket to floor 9/16˝ from jamb face and7/8˝ from jamb edge. Remove floor bracket and proceed toStep 5.
040105 PF116
5. Hang Doors by (A) inserting 1001 Top Pivot into 1010 Top Pivot Socket.Lock into place with locking lever. Then (B) insert 1125 Hanger into 1121Door Plate. Lock into place with locking arm. (C) Tilt doors slightly to allow1011 Floor Bracket to slide under 1706 Bottom Pivot. Insert 1706 into holeof 1011. Reattach 1011 to floor
6. Mount Aligners (1808) on back sideof lead doors. (4 Door Sets Only)
7. Check for Proper Door Operation: clearance, alignment, adjust-ments, etc. should be made at this time. If adjustments arerequired, they can be made at Track Pivot Socket (1010) and FloorBracket (1011). Setting, door warpage and other uncontrollableconditions may require later areadjustments.
Note: Doors must be parallel with track for proper operation.
8. Attach Knobs drill 3/16˝ hole 36˝from bottom, and in center of #2and #3 doors.
9. ADJUST SNUBBER (1155) Close doors, slide 1155 untilit touches 1125. Open doors. move #1155 1/8˝ closer to#1125 ant tighten.
040105 PF117
Bipass Track & Hardware 150 lbs. & 250 lbs.
150 lbs & 250 lbs. Panel By-Pass Doors• For installation of two bypassing doors with 1 3/8˝ or 1 3/4˝ thick panels weighing up to 150 lbs. each• Large 1˝ wheels provide smooth rolling action• Easy to install snap-in feature makes hangers a “snap” to install• Vertical adjustments can be made after installations• Supports panels weighing up to 150 lbs• Durable V-groove aluminum track provides smooth, quiet operation• Track spacer allows for easy installation of bypass and tripass doors• Panel Width equals known finished opening width plus 1˝ per overlap, divided by number of panels• Opening Width equals known finished panel width multiplied by number of panels, less 1˝ per overlap• Door Height equals 3˝ less than finished opening height• For multi-panel sizing information, contact A & F Wood Products• 250 lb. Large 1˝ Ball Bearing wheels provide smooth rolling action• Supports panels weighing up to 250 lbs.
2 Door System
WRENCH1 - 1750Wrench
SPLIT FLOOR GUIDE1 - Splitfloorgu
SPACER1- Spacer
HANGER1- 1750HDW
2 Door System: One set consists of: 2- Track, 2- Spacers, 2- Hardware, 1- Floor Guide, 1- Wrench
3 Door System: One set consists of: 2- Track, 2- Spacers, 3- Hardware, 2- Floor Guide, 1- Wrench
4 Door System: One set consists of: 2- Track, 2- Spacers, 4- Hardware, 4- Floor Guide, 1- Wrench
3 Door System 4 Door System
TRACK
040105 PF118
Bipass Track & Hardware 60 lbs.
60 lb. Panel Bi-Pass Doors• For installation of 2 bi-passing doors, with 3/4˝ to 1 3/8˝ thick panels weighing up to 60 lbs. each• Slotted hangers easy to adjust• Self-aligning wheel system• Permanently lubricated thermoplastic wheel• Supports panels weighing up to 60 lbs.• Vertical adjustments can be made after installation• Hanger system allows for easy panel removal• V-groove galvanized steel or aluminum track provides smooth, quiet operation• Spring loaded top pivot and roller guide for easy installation• Permanently lubricated roller guide• Durable pre-painted track• All metal components galvanized against corrosion• Panel Width equals known finished opening width plus1˝ per overlap, divide by number of panels• Opening Width equals known finished panel width multiplied by number of panels, less 1” per overlap• Door Height equals 1 3/4˝ less than finished opening height• BPC60,PBC60APB60 conform to ANSI A156.14 type D8742; PBC60AF conforms to type D8752, BFC30 conforms
to ANSI A156.14 type D8622
TRACK HANGER SPLIT FLOOR GUIDE FINGER PULL
2 Door System 3 Door System 4 Door System
2 Door System: One set consists of: 1- Steel Track, 1-Pr. Hangers, 1- Floor Guide, 2-Finger Pulls
3 Door System: One set consists of: 1- Steel Track, 2-Prs. Hangers, 2- Floor Guide, 3-Finger Pulls
4 Door System: One set consists of: 1- Steel Track, 3-Prs. Hangers, 2- Floor Guide, 4-Finger Pulls
040105 PF119
Bipass Door Installation InstructionsFor Doors 150/250 lbs.This package contains all the necessary hardware components for complete installation of your sliding (Bi-Pass) HeavyDuty Door
Set ContentsAluminum Track, SpacersSnap-in HantersSnap in door PlatesFloor Guide
FastnersWrench
Headroom Details
Door Height= 3˝ less than the finished opening.
How To Install(Read all steps prior to installation)
Step 1Insert (2) Hangers per track. Clip Track units together using Track Spacers – one at each ed and one in the middle forTrack 72” and over. See Figure 2.
Position Track into opening. Pre-drill 3/32” Pilot Holes, fasten with screws provided.Secure all Screws in Track and remove plastic Track Spacers.
040105 PF120
Facia option not included.
Facia optionnot included.
Bipass Door Installation InstructionsFor Doors 150/250 lbs. (cont’d)Step 2 (Optional)For easy access for hangers, same as Step #1 exceptCut Track 1˝ less than finished opening and install Track toHeader with 1˝ clearance at one Jamb. See Figure #4 and #5. Do Not Cut Fascia.
Step 3Position Hager Plates so edge of Hanger Plates are minimumof 5/8˝ from edge of door. Pre-drill 3/32˝ Pilot Holes.Screw Hanger Plates to top of door along center lineusing #8 x 1˝ Pan Head Screws provided. See Figure #6
Step 4Install Floor Guide in the center of the opening plumb withcenter of the Track choosing hole combinations toset spaces for 1 3/8˝ or 1 3/4˝ doors.
Step 5Install Door Hangers, lift door in the upward motion,snapping the post in Hanger Plate. Turn the Post to adjustvertically for height and plumb using Wrench provided.(Do Not unscrew Post from Hanger). To remove door,activate label in direction of white arrow with a Flute backScrew Driver as shown. See figure 8.
040105 PF121
Bipass 60 lbs. Installation Instructions
• For Steel Track - 1 3/8˝ doors, install 8902 or 8906 hangers on both front and rear doors.For 1˝ – 1 1/8˝ doors, install 8902 or 8906 hangers on front doors, 8901 or 8905 on rear doors.
• Aluminum Track (non-fascia) – For 1 3/8˝ doors, install 8901/8905 hangers on front door, 8902/8906 on rear door.For 1 3/4” doors, reverse above hanger positions on doors: For 1˝ – 1 1/8˝ doors, install 8902/8906 hangers on bothfront and rear doors.
• Alum. Fascia Track – For 1 3/8˝ doors, install 8902/8906 hangers on both front and rear doors.For 1˝ - 1 1/8˝ doors, install 8902/8906 on front door, 8901/8905 on rear door.
Note: Make opening width a min. of 1˝ (25mm) less than set size indicated, to provide door overlap at center. Ex: Forset No. 8848 make opening a maximum of 47˝ (1.19m).
With non-fascia track, track must clear fascia by (A) and shelves or drawers `by a minimum of(B). Fascia track mounts flush with front edge of head jamb.Door Size 3/4˝ 1˝ – 1 1/8˝ 1 3/8˝Steel track A N/A 3/8˝ 5/8˝Alum track A 0˝ 3/8˝ 7/8˝Shelf B 2 3/4˝ 3 1/2˝ 4˝
Step 1 - Screw track to head jamb with track centered between jambs. Allow 1 1/4˝ (32mm) minimum headroom at topfor hardware, plus 1/4˝ to 5/8˝ (6-16mm) clearance between door and floor. To obtain this, the recommended doorheight is 1 3/4˝ (44mm) less than the finished opening height. This provides 5/16˝ (8mm) adjustment for plumbing tojamb.
Step 2 - Hanger plate is self seating at top of door. With single wheel hangers, mount 1/2˝(13mm) from edge of door; mount twin wheel hangers 1 3/4˝ (44mm) from edge. Place screws atarrows on hanger plate.
Step 3 - Lift doors on track, installing the inside ore rear door first. Angle door aprox. 15 degrees to engage wheels intrack.
Step 4 - To align the doors back off on hanger screws slightly, insert screwdriver in hanger slot and adjust for height andplumb. Finally, tighten screws.
Step 5 - When using adjustable floor guide (left below), insert nylon piece in metalplate slots corresponding to door size, then locate under doors at center of opening.If using one-piece nylon guide (opt.) for 1 3/8˝ doors only, position same as foradjustable guide.
040105 PF122
Snap-In Track and Hanger SystemFor Bifold, Bypass and Pocket Doors
• Easier installation than other Stanley or competitive models• Simply lift door and snap hanger into place• Unique design improves performance and handling• No special handling or tools necessary to engage hanger• Fewer components to handle more applications• Patent pending
• Quick and easy as 1, 2, 3• convenient snap-in hanger for trouble-free alignment• Larger wheels provide smoother, more quiet ride• Track spacer facilitates installation of bypass doors• Common track allows for reduced inventory and greater likelihood
of having the correct product on the job when needed
1 2 3
040105 PF123
040105 PF124
pItem Description Size R.O. Units List
1-17502-0 2'0" x 6'8" Pocket 50" x 84" EA. Add for: 78.00
1-17502-2 2'2" x 6'8" Pocket 54" x 84" EA. Johnson 79.00
1-17502-4 2'4" x 6'8" Pocket 58" x 84" EA. #100 Track 80.25
1-17502-6 2'6" x 6'8" Pocket 62" x 84" EA. and Hardware 81.50
1-17502-8 2'8" x 6'8" Pocket 66" x 84" EA. $11.50 82.75
1-17503-0 3'0" x 6'8" Pocket 74" x 84" EA. 85.00
1-17504-0 4'0" x 6'8" Pocket 98" x 84" EA. 132.00 For 1 3/8" Doors
Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation
Item Description Size R.O. Units List
1-17502-070 2'0" x 7'0" Pocket 50" x 88" EA. Add for: 95.50 P1-17502-270 2'2" x 7'0" Pocket 54" x 88" EA. Johnson 97.50 O1-17502-470 2'4" x 7'0" Pocket 58" x 88" EA. #100 Track 97.50 C1-17502-670 2'6" x 7'0" Pocket 62" x 88" EA. and Hardware 99.00 K1-17502-870 2'8" x 7'0" Pocket 66" x 88" EA. $11.50 100.00 E1-17503-070 3'0" x 7'0" Pocket 74" x 88" EA. 102.25 T1-17504-070 4'0" x 7'0" Pocket 98" x 88" EA. 149.50 For 1 3/8" Doors
Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation DO
Item Description Size R.O Units List O1-17502-080 2'0" x 8'0" Pocket 50" x 100" EA. Add for: 110.25 R1-17502-280 2'2" x 8'0" Pocket 54" x 100" EA. Johnson 112.50
1-17502-480 2'4" x 8'0" Pocket 58" x 100" EA. #100 Track 112.50 F1-17502-680 2'6" x 8'0" Pocket 62" x 100" EA. and Hardware 114.00 R1-17502-880 2'8" x 8'0" Pocket 66" x 100" EA. $11.50 114.75 A1-17503-080 3'0" x 8'0" Pocket 74" x 100" EA. 117.00 M1-17504-080 4'0" x 8'0" Pocket 98" x 100" EA. 162.00 For 1 3/8" Doors EIncludes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation S
Item Description Size R.O. Units List
2000 K.D. Pocket 6/8 Height
1-750 2'0" x 6'8" KD Pocket 49 1/4 x 84 EA. Add for: 81.50
1-750 2'2" x 6'8" KD Pocket 53 1/4 x 84 EA. Johnson 81.50
1-750 2'4" x 6'8" KD Pocket 57 1/4 x 84 EA. #100 Track 81.50
1-750 2'6" x 6'8" KD Pocket 61 1/4 x 84 EA. and Hardware 81.50
1-750 2'8" x 6'8" KD Pocket 65 1/4 x 84 EA. $11.50 81.50 Marked for
1-750 3'0" x 6'8" KD Pocket 73 1/4 x 84 EA. 81.50 cutting to any
Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation shorter length
Item Description Size R.O. Units List
1-17502-0MULLI 2 - 2'0" x 6'8" Pocket 98" x 84" EA. $191.00
1-17502-4MULLI 2 - 2'4" x 6'8" Pocket 112" x 84" EA. $195.00
1-17502-6MULLI 2 - 2'6" x 6'8" Pocket 122" x 84" EA. $198.00
1-17502-8MULLI 2 - 2'8" x 6'8" Pocket 130" x 84" EA. $200.00
1-17503-0MULLI 2 - 3'0" x 6'8" Pocket 146" x 84" EA. $204.50 Biparting 6'x8" Doors
1-17504-0MULLI 2 - 4'0" x 6'8" Pocket 194" x 84" EA. $295.00
Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation For 1 3/8" Doors
40105 Page 1
Item Description Size R.O. Units List
1-17502-070MU 2 - 2'0" x 7'0" Pocket 98" x 88" EA. $191.00
1-17502-470MU 2 - 2'4" x 7'0" Pocket 112" x 88" EA. $195.00
1-17502-670MU 2 - 2'6" x 7'0" Pocket 122" x 88" EA. $198.00
1-17502-870MU 2 - 2'8" x 7'0" Pocket 130" x 88" EA. $200.00
1-17503-070MU 2 - 3'0" x 7'0" Pocket 146" x 88" EA. $204.50 Biparting 7'x0" Doors
1-17504-070MU 2 - 4'0" x 7'0" Pocket 194" x 88" EA. $295.00
Includes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation For 1 3/8" Doors
Item Description Size R.O. Units List
1-17502-080MU 2 - 2'0" x 8'0" Pocket 98" x 100" EA. $255.25 P1-17502-480MU 2 - 2'4" x 8'0" Pocket 112" x 100" EA. $259.50 O1-17502-680MU 2 - 2'6" x 8'0" Pocket 122" x 100" EA. $262.00 C1-17502-880MU 2 - 2'8" x 8'0" Pocket 130" x 100" EA. $264.25 K1-17503-080MU 2 - 3'0" x 8'0" Pocket 146" x 100" EA. $268.50 Biparting 8'x0" Doors E1-17504-080MU 2 - 4'0" x 8'0" Pocket 194" x 100" EA. $326.00 TIncludes Stanley 4-wheel "Snap In" hangers with quick release tab for easy installation For 1 3/8" Doors
DO
Item Description Units List O1-1755JAMBKIT 1755 Jamb Kit Clear Pine EA. 65.45 RUsed for finish pocket door entry
Cut to length for easy installation FCan be stained or painted R
AME
Item Description Units List S1-1756JAMBKIT 1756 Jamb Kit Paint Grade EA. 40.33
Used for finish pocket door entry
Cut to length for easy installation
Can be stained or painted
Item Description Units List
1-2X6WALL 2 X 6 Wall Pocket EA. 75.00
Used with 2 x 6 wall application
2 x 6 Wall
Item Description Units List
1-5/8DRYWALL 5/8” Drywall for Pockets EA. 10.00
Used with 5/8" drywall application
5/8" Drywall
40105 Page 2
040105 PF125
Item Description Units List
1-FOR13/4 1 3/4" Door Opening EA. 5.00
on Pockets
To provide opening for 1 3/4 door
Warning: Do to constricting wall widths of 3 1/2" stud, doors may warp beyond pocket opening.
2 x 6 studs guarantes ample room for 1 3/4" doors.
Item Description Units List
1-70EXTENTION #1752 7/0 Extent ion Kit EA. 22.50
(for Built-Up Pockets) PUsed to add extra height to the standard 6/8 Oheight frames C
KItem Description Units List E1-80EXTENTION #1753 8/0 Extention Kit EA. 39.50 T
(for Built-Up Pockets)
Used for adding extra height to the standard D6/8 height frames O
O1-752-70KIT #752 7-0 Extent ion Kit EA. 22.50 R
(for 2000 K.D. Pockets)
Used to add extra height to the standard A6/8 height frames C
CItem Description Units List E1-753-80KIT #753 8-0 Extent ion Kit EA. 32.50 S
(for 2000 K.D. Pockets) SUsed to add extra height to the standard O6/8 height frames R
IE
Item Description Units List S1-754-90KIT #754 9-0 Extention Kit EA. 47.00
(for 2000 K.D. Pockets)
Used to add extra height to the standard
6/8 height frames
Baskets Description Size Units List
1-17502-0BSKT 2'0" X 6'8" Basket EA. 39.00
1-17502-2BSKT 2'2" X 6'8" Basket EA. 39.50
1-17502-4BSKT 2'4" X 6'8" Basket EA. 40.13
1-17502-6BSKT 2'6" X 6'8" Basket EA. 40.75
1-17502-8BSKT 2'8" X 6'8" Basket EA. 41.38
1-17503-0BSKT 3'0" X 6'8" Basket EA. 42.50
1-17504-0BSKT 4'0" X 6'8" Basket EA. 66.00
Pre-Assembled basket to accept a slab door For 1 3/8" Doors
40105 Page 3
040105 PF126
Item Description Size Units List
1-17502-0HEAD 2'0" Header EA. 39.00
1-17502-2HEAD 2'2" Header EA. 39.50
1-17502-4HEAD 2'4" Header EA. 40.13
1-17502-6HEAD 2'6" Header EA. 40.75
1-17502-8HEAD 2'8" Header EA. 41.38
1-17503-0HEAD 3'0" Header EA. 42.50
1-17504-0HEAD 4'0" Header EA. 66.00
1-750KDHEAD K/D Header EA. 40.75 PPre Assembled Header unit with cut marks on header make for easy sizing O
CK
Item Description Unit List E1-751CONNECTOR #751 Mullion Connector EA. 14.79 TJoins 2 pocket door frames to make one large
doorway DCan be used for Built Ups & K.D. Units O
OR
Item Description Size Units List
Track H1-17502-0TRACK 2'0" Track 47 ¼" EA. 9.72 A1-17502-2TRACK 2'2" Track 52 ¼" EA. 11.36 R1-17502-4TRACK 2'4" Track 54 ¼" EA. 11.36 D1-17502-6TRACK 2'6" Track 58 ¼" EA. 12.18 W1-17502-8TRACK 2'8" Track 62 ¼" EA. 12.97 A1-17503-0TRACK 3'0" Track 70 ¼" EA. 14.64 R1-17504-0TRACK 4'0" Track 96” EA 18.70 E1-17505-0TRACK 5'0" Track 120” EA 22.95
1-17506-0TRACK 6'0" Track 144” EA 27.71
1-750KDTRACK K/D Track 69" EA 14.60
Item Description Units List
1-1750HDW 1750 Hardware #150lbs EA. 12.58
Four large wheels easy snap-in installation
Use with 150 lbs bipass panels
Pocket Hardware for single 1-1/8" to 1 3/4" door up to 150 lbs
Set Includes: 1-Wrench, 2-Splitfloor guides, 2-Hangers
Item Description Units List
1-1750BALLBEAR 1750 Hardware #250 lbs EA. 67.11
Ball Bearing
Four large wheels, easy snap-in installation
Use with 250 lbs bipass panels
Pocket Hardware for single 1-1/8" to 1 3/4" door up to 250 lbs
Set Includes: 1-Wrench, 2-Splitfloor guides, 2-Ball Bearing Hangers
40105 Page 4
040105 PF127
Item Description Units List
100HDW 100 Hardware Set Johnson EA. 11.94
#1025
3 wheel
Pocket Hardware for single 1-1/8" to 1 3/4" door up to 125 lbs
Set Includes: 1-Wrench, 2-Guides, 2-Hangers
Item Description Units List
100HDWBB 100 Ball Bearing Hardware Set Johnson EA. 32.17
3 wheel
PPocket Hardware for single 1-1/8" to 1 3/4" door up to 250 lbs OSet Includes: 1-Wrench, 2-Guides, 2-Ball Bearing Hangers C
KItem Description Units List E1-BUMPER Bumper for Pocket EA. 0.38 T
Plastic Finish
DFor Pocket Doors O
OR
Item Description Units List
1 – WRENCH Adjustable Wrench EA. 0.47 HUsed to adjust hardware A
RDW
Item Description List A1-FLOORBRACKET Floor brackets 1 set K.D. 3.36 R2 brackets, nails bumper screws t assemble kd pocket unit E
Item Description Units List
1-68KDSTIFFINE KD 6/8 Stiffener EA. 5.31
Steel Stiffener w/wood for K.D. Pocket
83 1/2" Length
Item Description Units List
1-BU68STIFFINE Built Up 6/8 Stiffener EA. 3.78
Steel Stiffener for 6/8 built up Pocket
82 1/8" Length
40105 Page 5
Set
EA.
040105 PF128
Item Description Units List
1-BU70STIFFENE Built Up 7/0 Stiffener EA. 4.00
Steel Stiffener for 7/0 built up Pocket
86 1/8" Length
Item Description Units List
1-BU80STIFFENE Built Up 8/0 Stiffener EA. 4.97
Steel Stiffener for 8/0 built up Pocket
98 1/8" Length POCK
Item Description Units List E1-13/4FLOORGUI #111 - Floor Guide 1 ¾) EA. 4.85 Tadjusts to center door in pocket
Adjustable DGuides bottom of door into pocket O
OR
Item Description Units List H1-13/8FLOORGUI #107 - Floor Guide 1 3/8) EA. 1.74 AAdjusts to center door of pocket RGuides Bottom of door into pocket D
WARE
Item Description Units List
1-BRACKET Universal Bracket EA. 0.94
for K.D.
End Brackets for K.D. Headers
aka - wall bracket
Item Description Units List
1-BUFLOORPLATE Built-Up Floor Plate EA. 0.47
Floor plate for built up pocket
aka spacer/sill plate
40105 Page 6
040105 PF129
Item Description Units List
1-SPLITFLOORGU #113 Split Floor Guide EA. 3.27
Adjusts to center door in pocket
Adjustable
1 Pair of split floor guides
Item Description Units List P1-MULLIONSTOP #115 Center Stop EA. 3.24 O
CKET
DO
Item Description Finish Units List OPocket Latches - Privacy R263-POCKETP26D Pocket Door Latch – Privacy US26D EA. 13.60
263-POCKETPUS3 Pocket Door Latch – Privacy US3 EA. 12.33 HPrivacy Sliding Door Lock A
RDWARE
Item Description Finish Units List
Pocket Latches - Pulls
263-POCKETL26D Pocket Pull US26D EA. 10.41
263-POCKETLUS3 Pocket Pull US3 EA. 9.35
Passage Sliding Door Lock
40105 Page 7
040105 PF130
30 lbs Bifold Track & Hardware Set for 1 1/8" to 1 3/8" panels Light Duty - Complete Set
2 Door System 4 Door System
Item Description Size Units Panel List Price
26-20BIFSET 2'0" Bifold Track & Hdw Set 24” EA 2 9.52
26-26BIFSET 2'6" Bifold Track & Hdw Set 30” EA 2 10.12
26-30BIFSET 3'0" Bifold Track & Hdw Set 36” EA 2 10.75
26-40BIFSET 4'0" Bifold Track & Hdw Set 48” EA 4 18.02
26-50BIFSET 5'0" Bifold Track & Hdw Set 60” EA 4 19.38
26-60BIFSET 6'0" Bifold Track & Hdw Set 72” EA 4 20.32
26-80BIFSET 8'0" Bifold Track & Hdw Set 96” EA 4 22.70
Complete Bifold Track & Hardware Set
One set consists of 1 – Track, 2 – Snuggers, 1 – Top Pivot, 1 – Guide Wheel, 1 – Bottom Pivot, 1- Knob, 1 – Jamb Bracket BI
Item Description Size Units List Price FTrack 30lbs O26-20BIFTR 2'0" Bifold Track 30 lbs 24” EA 2 3.61 L26-26BIFTR 2'6" Bifold Track 30 lbs 30” EA 2 4.21 D26-30BIFTR 3'0" Bifold Track 30 lbs 36” EA 2 4.85
26-40BIFTR 4'0" Bifold Track 30 lbs 48” EA 4 6.21 D26-50BIFTR 5'0" Bifold Track 30 lbs 60” EA 4 7.35 O26-60BIFTR 6'0" Bifold Track 30 lbs 72” EA 4 8.50 O26-80BIFTR 8'0" Bifold Track 30 lbs 96” EA 4 10.88 R
Item Description Units Panel List Price HBifold Hardware Standard 30 Lbs A26-BIFHDW 2 Panel Bifold Hardware EA 2p Set 5.91 RSet includes: 1-Track, 1-Roller,1-top Pivot, 1 Pivot Lock,1-Bottom Pivot,1-Floor Pivot Bracket, D1-Non-Mortise Lift off Hinge, 1 4 Door Aligner, 1 Knob, 1-adjustment Wrench WNote: For a 4 panel door you need to order two packages of bifold hardware A
RItem Description Units List Price E
26-TOPPIVOT Top Pivot 30lb Bifold Hdw EA 1.02
Used with top pivot brackets on door panel
Item Description Units List Price
26-BTMPIVOT Bottom Pivot 30lb Bifold Hdw EA 0.77
Provides vertical adjustment of doors
Slips into jamb bracket at floor level and can be moved horizontally
Item Description Units List Price
26-GUIDEWHE Guide Wheel 30lb Bifold EA 1.19
Provides door movement on track
Item Description Units List Price
26-KNOBPLAS Plastic Knob 30 lb Bifold EA 0.60
Use on two or four door panels
Open and close doors easily
40105 Page8
040105 PF131
Item Description Units List Price
26-SNUGGER Snugger 30 lb Bifold EA 2p Set 0.64
Holds doors snub 4p Set 0.81
Item Description Units List Price
26-JAMBBRAC Jamb Bracket 30 lb Bifold EA 1.06
Easy horizontal adjustment
BItem Description Units List Price I
F26-ALLIGNER Alligner 30 lb Bifold EA 0.98 OFor use in four door installations LUse on all door sizes DBrings leading dor edges into alignment
DItem Description Units List Price O26-BIFHINGE Non-Mortise Hinge EA 1.87 OFor surface mounting RNo Mortising required
HA
75 lbs Bifold Track & Hardware Set for 1 1/8" to 1 3/8" panels Heavy Duty - Complete Set R2 Door System 4 Door System D
Item Description Size Units Panel List Price WA
2601-30BIFSET 3'0" Bifold Track & Hdw Set 75lbs 36” EA 2 60.02 R2601-40BIFSET 4'0" Bifold Track & Hdw Set 75lbs 48’ EA 4 110.38 E2601-50BIFSET 5'0" Bifold Track & Hdw Set 75lbs 60” EA 4 114.84
2601-60BIFSET 6'0" Bifold Track & Hdw Set 75lbs 72” EA 4 118.97
2601-80BIFSET 8'0" Bifold Track & Hdw Set 75lbs 96” EA 4 127.93
Heavy duty track and hardware for doors weighing over 75 lbs each panel
One set consists of: 1 Track, 3 Non-Mortise Hinges, 2 Bottom Pivots, 2 Knobs, 1 Hardware, 1 Bottom Pivot Bracket, 1 Wrench, 1 Installation Hardware, 2 Door Aligners, 1 Top Pivot
Item Description Size units List Price
Track 75 lbs
2601-30BIFTR 3'0" Bifold Track 75 lbs. 36" EA 13.98
2601-40BIFTR 4'0" Bifold Track 75 lbs. 48” EA 18.32
2601-50BIFTR 5'0" Bifold Track 75 lbs. 60” EA 22.78
2601-60BIFTR 6'0" Bifold Track 75 lbs. 72” EA 26.90
2601-80BIFTR 8'0" Bifold Track 75 lbs. 96” EA 35.87
Item Description Units Panel List Price
Bifold Hardware Standard 75 Lbs
2601-HDWBIF2P #291 Hardware 75 Lbs Complete Set EA 2p Set 46.03
2601-HDWBIF4P #291 Hardware 75 Lbs Complete Set EA 4p Set 92.06
Commercial Based Hardware
40105 Page 9
040105 PF132
Item Description Units List Price
2601-HDW #291 Hardware 75 Lbs Single Piece EA 6.63
Item Description Units List Price
2601-TOPPIVOT Top Pivot 75Lbs EA 17.00
Top pivot bracket
BI
Item Description Units List Price F2601-STOP Track Stop 75 Lbs EA 1.62 OTrack stop L
D
Item Description Units List Price DO
2601-BTMPIVOT Bottom Pivot Bracket 75 Lbs EA 6.12 OProvides vertical adjustment on doors R
HItem Description Units List Price A
R2601-NONHING Non-Mortise Hinge 75 lbs EA 4.38 DFor surface mounting W
AR
Item Description Units List Price E
2601-ALLIGNER Alligner 75lbs EA 0.94
Brings leading door into alignment
Item Description Units List Price
2601-WRENCH Wrench 75lbs EA 0.47
Used for adjustments
Item Description Units List Price
2601-KNOB Plastic Knob 75lbs EA 0.55
Open and close doors easily
Item Description Units List Price
2601-INSTHDW Installation Hardware 75lb EA 3.40
Packaged hardware
40105 Page 10
040105 PF133
Item Description Units Panel List Price
150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
2 Door System
261-40BIPAS2D 4/0 Bipass Track & Hdw 150 lbs 2dr 48” Opening EA 2 67.45
261-50BIPAS2D 5/0 Bipass Track & Hdw 150 lbs 2dr 60” Opening EA 2 72.38
261-60BIPAS2D 6/0 Bipass Track & Hdw 150 lbs 2dr 72” Opening EA 2 77.31
261-80BIPAS2D 8/0 Bipass Track & Hdw 150lbs 2dr 96” Opening EA 2 85.43
Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench
BItem Description Units Panel List Price I150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set P3 Door System A
S261-40BIPAS3D 4/0 Bipass Track & Hdw 150 lbs 3dr 48” Opening EA 3 87.00 S261-50BIPAS3D 5/0 Bipass Track & Hdw 150 lbs 3dr 60” Opening EA 3 91.93
261-60BIPAS3D 6/0 Bipass Track & Hdw 150 lbs 3dr 72” Opening EA 3 96.86 D261-80BIPAS3D 8/0 Bipass Track & Hdw 150lbs 3dr 96” Opening EA 3 104.98 OSet Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench O
R
Item Description Units Panel List Price H150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set A4 Door System 106.55 R261-40BIPAS4D 4/0 Bipass Track & Hdw 150 lbs 4dr 48” Opening EA 4 111.48 D261-50BIPAS4D 5/0 Bipass Track & Hdw 150 lbs 4dr 60” Opening EA 4 116.41 W261-60BIPAS4D 6/0 Bipass Track & Hdw 150 lbs 4dr 72” Opening EA 4 124.53 A261-80BIPAS4D 8/0 Bipass Track & Hdw 150lbs 4dr 96” Opening EA 4 RSet Includes: 2-Track, 4-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench E
Item Description Units Panel List Price
250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
2 Door System2611-40BIPAS2D 4/0 Bipass Track & Hdw 250 lbs 2dr 48” Opening EA 2 176.50
2611-50BIPAS2D 5/0 Bipass Track & Hdw 250 lbs 2dr 60” Opening EA 2 181.43
2611-60BIPAS2D 6/0 Bipass Track & Hdw 250 lbs 2dr 72” Opening EA 2 186.36
2611-80BIPAS2D 8/0 Bipass Track & Hdw 250lbs 2dr 96” Opening EA 2 194.48
Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench
Item Description Units Panel List Price
250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
3 Door System2611-40BIPAS3D 4/0 Bipass Track & Hdw 250 lbs 3dr 48” Opening EA 3 250.58
2611-50BIPAS3D 5/0 Bipass Track & Hdw 250 lbs 3dr 60” Opening EA 3 255.51
2611-60BIPAS3D 6/0 Bipass Track & Hdw 250 lbs 3dr 72” Opening EA 3 260.44
2611-80BIPAS3D 8/0 Bipass Track & Hdw 250lbs 3dr 96” Opening EA 3 268.56
Set Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench
40105 Page 11
040105 PF134
Item Description Units Panel List Price
250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
4 Door System2611-40BIPAS4D 4/0 Bipass Track & Hdw 250 lbs 4dr 48” Opening EA 4 324.66
2611-50BIPAS4D 5/0 Bipass Track & Hdw 250 lbs 4dr 60” Opening EA 4 329.59
2611-60BIPAS4D 6/0 Bipass Track & Hdw 250 lbs 4dr 72” Opening EA 4 334.52
2611-80BIPAS4D 8/0 Bipass Track & Hdw 250lbs 4dr 96” Opening EA 4 342.64
Set Includes: 2-Track, 4-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench
Item Description Units List Price BTrack 150 & 250 Lbs I1-17502-0TRACK 2'0" Track 48” 48" EA 9.72 P1-17502-6TRACK 2'6" Track 60” 60" EA 12.18 A1-17503-0TRACK 3'0 Track 72”" 72" EA 14.64 S1-17504-0TRACK 4'0" Track 96” 96" EA 18.70 S
DO
Item Description Units List Price O1-1750HDW #1750 Hardware Set EA 12.58 RFour large ball bearing wheels, easy snap-in installation feature
For use with panels weighing up to 150 lbs. HAR
Item Description Units List Price DW
1-1750BALLBEAR #1750 Ball Bearing Hardware Set EA 67.11 AFour large ball bearing wheels, easy snap-in installation feature RFor use with panels weighing up to 250 lbs. E
Item Description Units List Price
1-WRENCH Adjusting Wrench EA 0.47
Item Description Units List Price
Bipass Track Spacer EA 7.95
Provides correct spacing between tracks for 1 ¾ doors
Simplifies installation of 2 or more tracks
Item Description Units List Price
29-BIPASSFLRGU Bipass Floor Guide Adjustable EA 6.97
Adjustable for 1 3/8” to 1 ¾” thick by passing doors
40105 Page 12
29-BIPASSPACE
040105 PF135
Item Description Units Panel List Price
150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
2 Door System
261-40BIPAS2D 4/0 Bipass Track & Hdw 150 lbs 2dr 48” Opening EA 2 67.45
261-50BIPAS2D 5/0 Bipass Track & Hdw 150 lbs 2dr 60” Opening EA 2 72.38
261-60BIPAS2D 6/0 Bipass Track & Hdw 150 lbs 2dr 72” Opening EA 2 77.31
261-80BIPAS2D 8/0 Bipass Track & Hdw 150lbs 2dr 96” Opening EA 2 85.43
Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench
BItem Description Units Panel List Price I150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set P3 Door System A
S261-40BIPAS3D 4/0 Bipass Track & Hdw 150 lbs 3dr 48” Opening EA 3 87.00 S261-50BIPAS3D 5/0 Bipass Track & Hdw 150 lbs 3dr 60” Opening EA 3 91.93
261-60BIPAS3D 6/0 Bipass Track & Hdw 150 lbs 3dr 72” Opening EA 3 96.86 D261-80BIPAS3D 8/0 Bipass Track & Hdw 150lbs 3dr 96” Opening EA 3 104.98 OSet Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench O
R
Item Description Units Panel List Price H150 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set A4 Door System 106.55 R261-40BIPAS4D 4/0 Bipass Track & Hdw 150 lbs 4dr 48” Opening EA 4 111.48 D261-50BIPAS4D 5/0 Bipass Track & Hdw 150 lbs 4dr 60” Opening EA 4 116.41 W261-60BIPAS4D 6/0 Bipass Track & Hdw 150 lbs 4dr 72” Opening EA 4 124.53 A261-80BIPAS4D 8/0 Bipass Track & Hdw 150lbs 4dr 96” Opening EA 4 RSet Includes: 2-Track, 4-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench E
Item Description Units Panel List Price
250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
2 Door System2611-40BIPAS2D 4/0 Bipass Track & Hdw 250 lbs 2dr 48” Opening EA 2 176.50
2611-50BIPAS2D 5/0 Bipass Track & Hdw 250 lbs 2dr 60” Opening EA 2 181.43
2611-60BIPAS2D 6/0 Bipass Track & Hdw 250 lbs 2dr 72” Opening EA 2 186.36
2611-80BIPAS2D 8/0 Bipass Track & Hdw 250lbs 2dr 96” Opening EA 2 194.48
Set Includes: 2-Track, 2-Hardware, 2-Spacers, 1-Floor Guide, 1 Wrench
Item Description Units Panel List Price
250 lbs Bipass Track & Hardware Set for 1 3/8" - 1 3/4" Doors - Complete Set
3 Door System2611-40BIPAS3D 4/0 Bipass Track & Hdw 250 lbs 3dr 48” Opening EA 3 250.58
2611-50BIPAS3D 5/0 Bipass Track & Hdw 250 lbs 3dr 60” Opening EA 3 255.51
2611-60BIPAS3D 6/0 Bipass Track & Hdw 250 lbs 3dr 72” Opening EA 3 260.44
2611-80BIPAS3D 8/0 Bipass Track & Hdw 250lbs 3dr 96” Opening EA 3 268.56
Set Includes: 2-Track, 3-Hardware, 2-Spacers, 2-Floor Guide, 1 Wrench
40105 Page 11
040105 PF136
5665 Sterling Drive • Howell, Michigan 48843Phone: 517.545.5811 • Fax: 517.545.5633 • Toll Free: 800.367.3292
www.afwood.com