BUILDING PERMIT SUBMITTAL REQUIREMENTS … · BUILDING PERMIT SUBMITTAL REQUIREMENTS ... determine...

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-51_MH_Manufactured_Mobile_Modular_Home_Installation_rev'd_3.7.2014_AKM.doc

of 2

BUILDING PERMIT SUBMITTAL REQUIREMENTS

**NEW MANUFACTURED/MOBILE/MODULAR HOME ** ‘New’ refers to the manufactured/mobile/modular home being ‘new’ to the parcel not the age of the unit. Completed Butte County Department of Developments Services building permit application (form DBP-1). Please furnish assessor’s parcel number for the proposed location. 3 site plans signed by the preparer of the plans (form DBP-2). Paper to draw site plans and site plan submittal requirements (form DBP-3) are available at the Development Services counter. At least one site plan must be 11” x 17”. NOTE: If the parcel is in the City of Biggs, the site plan must be reviewed and approved prior to submitting your building permit application. They can be reached at (530)868-5447. One (1) installation manual from the manufactured/mobile home manufacturer Marriage line information from manufactured/mobile home manufacturer if home is larger than a single wide, in duplicate Manufactured/Mobile home manufacturer’s floor plan in triplicate. If floor plan is not available it can be drawn by applicant. Floor plan requires dimensions of manufactured/mobile home, indicate all windows and exits, label each room and include any interior fixtures. At least one floor plan must be 11” x 17”. State approved or engineered tie down or foundation plans in duplicate

Butte County Manufactured Home Support Information sheet (form DBP-52) completed with information from manufactured/mobile home manufacturer’s installation instructions. This form is available at the Development Services counter or is available for download from our website at www.buttecounty.net/dds.

Flood Elevation Certificate, in duplicate, wet stamped and signed (if applicable). To determine if a parcel is in a flood zone go to our website at www.buttecounty.net/dds. Click on Parcel Lookup from the DDS Menu to do a search.

A copy of the creation deed may be required for the parcel if the parcel is undeveloped (vacant and never been built on). This will be determined during the permit review by the Land Development Department. Contact number (530)538-7266.

Butte County Department of Development Services PERMIT CENTER

7 County Center Drive, Oroville, CA 95965 Main Phone (530)538-7601 Permit Center Phone (530)538-6861 Fax (530)538-7785

FORM NO

DBP-51

http://www.buttecounty.net/dds


http://sk.chicomapworks.com/

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-51_MH_Manufactured_Mobile_Modular_Home_Installation_rev'd_3.7.2014_AKM.doc

of 2

If being placed on a Permanent Foundation System the following additional items will be required:

A copy of the current recorded grant deed with the legal description

A copy of the Title or Registration of the manufactured/mobile home or if it is a new manufactured/mobile home a copy of the Manufacturer’s Certificate of Origin (MCO)

If the parcel is in a sewer district (not on a septic system) a copy of the approved permit from the sewer district is required.

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-01_Building_Permit_Application_rev'd_3.6.2014_AKM.rtf

Page 1 of 1

PROJECT LOCATION APN

Property Address

City Location must not be in the city limits of Chico, Gridley, Oroville or Paradise, click below for parcel information

http://gismaps.buttecounty.net/flexviewer/bcdatasearch/index.html

WORKER'S COMPENSATION Policy Number

Carrier

If hiring other than a licensed contractor, a certificate of worker's compensation must be shown at the time of permit issuance

LENDING AGENCY Name Mailing Address City State Zip

DESCRIPTION OR SCOPE OF WORK APN

:

Mobile Home permits (other than installation, foundation, utilities & non-attached structures) are issued by the State. Tell staff if this permit is for a Mobile Home. Click below to see Manufactured Home Alterations and Permit Guidelines at: http://www.hcd.ca.gov/codes/mhp/HCD Phone: (916) 255-2501 Is this a Manufactured/Mobile Home (circle one) Yes / No

JOB VALUATION: (Enter value of labor, including non-contracted , plus materials charge) $

Square Feet Detail Living Area: Garage:

Open Area: Covered Area:

Structure Built without permits TOTAL SQ:

Proposed Change of Occupancy/Use - Note previous/current use below:

FOR OFFICE USE ONLY

Zoning: Flood Zone: SRA: YES NO NPDES YES NO Code Enf: YES NO Legal Lot: YES NO Occupancy Type Construction

Permit Tech: Date:

BUTTE COUNTY DEPARTMENT OF DEVELOPMENT SERVICES

BUILDING PERMIT APPLICATION* Phone: (530) 538-7601 Fax (530) 538-7785

Website: www.buttecounty.net/dds Payment of Fees Required at Time of Application

PLEASE PRINT CLEARLY

PERMIT NO:

BIN NO:

FORM NO DBP-1

CONTRACTOR

Name

Mailing Address

City State Zip

Phone Fax

Email Cell

License No. Class

ARCHITECT/ENGINEER

Name

Mailing Address

City State Zip

Phone Fax

Email Cell

CA State License No.

APPLICANT SIGNATURE AND DATE

Date:

Print Name: *When filed, this application and all supporting material becomes subject to the California Public Records Act. All public information related to this application is subject to public inspection and will be posted on the County's website for electronic access

PROPERTY OWNER INFORMATION Last Name First Name

Mailing Address

City State Zip

Phone Fax

Email Cell

APPLICANT Last Name First Name

Mailing Address

City State Zip

Phone Fax

Email Cell


http://www.hcd.ca.gov/codes/mhp/HCD


K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-02_Site_Plan_Requirements_rev'd_3.7.2014_AKM.docx

Page 1 of 1

Butte County Department of Development Services

PERMIT CENTER 7 County Center Drive, Oroville, CA 95965

Main Phone (530)538-7601 Permit Center Phone (530)538-6861 Fax (530)538-7785

FORM NO DBP-2

BUILDING PERMIT SUBMITTAL REQUIREMENTS SITE PLAN REQUIREMENTS

GENERAL INFORMATION Your site plan may be reviewed by various departments: Building, Planning, Environmental Health, Public Works, CDF, Agricultural Commission, etc. so you will need to include information to satisfy numerous agencies.

Please label all items as clearly and completely as possible. Site plans must be fully dimensioned and clearly drawn on clean paper. Size: 11” x 17” Blow-ups or insets may be used to provide more detail where required. (Note: A scaled site plan may be required, if necessary for septic system permit or other plan review.)

REQUIRED ITEMS Owner’s name Assessor’s Parcel Number North arrow Property lines with dimensions: As shown on assessors map or parcel map Distances between improvements and from property lines Setbacks Any features such as cliffs or areas of slope: Include direction & approximate degree

of slope New buildings are required to meet Minimum Erosion and Sediment Controls Measures or Best Management Practices (BMP)

EXISTING AND PROPOSED ON-SITE IMPROVEMENTS INCLUDING: Buildings or other structures Pools Tanks Retaining walls Cuts and/or fills

ROAD FEATURES INCLUDING: Location and name of frontage road(s) serving property Location of driveway Right-of-way Easements

ALL WATER RELATED FEATURES INCLUDING: Flood zone Septic / Sewage disposal systems (original and replacement) Wells Waterlines Springs Creeks or Streams - Seasonal creeks and drainage ditches

http://www.buhecounty.net/dds

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-03_Site_Plan_Paper_rev'd_3.6.2014_AKM.doc Page 1 of 1

FORM NO

DBP-3



K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-10_Fee_Estimate_Worksheet_Manufactured_Homes_rev'd_3.6.2014_AKM.doc

Page 1 of 2

FEE ESTIMATE WORKSHEET FOR

MANUFACTURED HOME INSTALLATION

In order to give an accurate fee estimate we will need the following information. Please complete as much information as possible to allow us to provide the most accurate estimate. ** All Manufactured Homes installed in Butte County are required to be HUD approved – Must be 1976 or newer

CONTACT NAME: ____________________________________________________________

Are you the owner of the property: _____ Contractor: ______ other: ______________ DAYTIME TELEPHONE NUMBER: _____________________________________________ EMAIL: ______________________________________________________________________ OWNER NAME: _______________________________________________________________ PROPERTY ADDRESS OR LOCATION: __________________________________________ ASSESSORS PARCEL NUMBER (APN): __________________________________________ TODAY’S DATE: _______________________________________________________________ **SIGNATURE: ________________________________________________________________

**DISCLAIMER

By signing this document I am aware that it is only to be used as a guide in the calculation of Building Permit type fees. The Department of Development Services, Building Division does not warrant any part of said document. Actual fees may vary at time of Permit issuance based on conditions, and/or scope of work, and/or any newly adopted ordinances/resolutions/law/statute (Federal/State/County/City) and/or the imposition of other fees by City, County, State or Federal. This document does not warrant any fees not falling within the purview of the Department of Development Services, Building Division. This is not an exact document, henceforth; you are encouraged to verify all fees and requirements with the appropriate ordinances/resolutions/codes/laws/statutes before any reliance upon such estimate.

**When filed, this form and all supporting material becomes subject to the California Public Records Act. All public information related to this form is subject to public inspection and will be posted on the County's website for electronic access. Note: We provide the first fee estimate free of charge. However, any additional requests will be charged at our hourly rate ($127.00) with a minimum charge of $32.00 for 15 minutes. We will try to provide all fee estimates within 72 hours of receiving this document. Thank you.

Page 2 must be completed in order to receive the requested estimate.


7 County Center Drive, Oroville, CA 95965 Main Phone (530) 538-7601 Permit Center Phone (530) 538-6861 Fax (530) 538-7785

FORM NO

DBP-10

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-10_Fee_Estimate_Worksheet_Manufactured_Homes_rev'd_3.6.2014_AKM.doc

Page 2 of 2

SQUARE FOOTAGE (SQ FTG) OF PROPOSED MANUFACTURED HOME AND ANY ATTACHMENTS: Manufactured Home (SQ FTG): ____________________ Please answer the following questions:

Will this be a permanent second dwelling (Circle one) YES NO Is this a temporary second dwelling (Aunt Minnie) (Circle one) YES NO Is this a soft set foundation (Circle one) YES NO Or is this a permanent foundation (Circle one) YES NO Is this a replacement home (Circle one) YES NO

Attached Garage Shop/Storage (SQ FTG):____________________________________ Stairs/Landing/Deck/Uncovered Porch Areas (SQ FTG):________________________ Covered Porch/Patio/Deck Areas (SQ FTG): __________________________________ Carport/Awnings (SQ FTG): _______________________________________________

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-52_MH_Support_Data_20090814_3.7.2014_AKM.docx

Page 1 of 1

Butte County Building Division MANUFACTURED HOME SUPPORT DATA

FORM NO

DBP-52

Owner's name: Home Manufacturer:

A.P. # - - Manufacture Year:

Model Number / Name: Width: (ft.) Length: (ft.) FOOTINGS: Wood - pressure treated or foundation grade [ ] other: [ ] SUPPORTS: Concrete block [ ] other: [ ]

Provide manufacturer's installation manual, support blocking requirements and state approved or engineered foundation or tie down system specifications.

SINGLE WIDE

Pier Footing Sizes and Locations MULTI-WIDE

Line 1 Line 2

Line 1

-------------------------------------------------- ------------ Line 1 Section 1 Line 2

-------------------------------------------------- ------------ Line 3 -------------------------------------------------- -----------

Section 2 Line 2

-------------------------------------------------- ------------ Line 4 (triple wide only) --------------------------------------------------------------

Section 3 Line 2

Line 1 Piers: Snow Load: psf Minimum size piers: [ ] X [ ] Snow Load requirements may be obtained at Spacing maximum: ' " http://sk.chicomapworks.com/ From ends maximum: ' " Insert AP #, view snow load in lower right corner.

Line 2 Piers: Line 1 Openings: Minimum size piers: [ ] X [ ] Minimum size pier [ ] X [ ] Spacing maximum: ' " Required at each side of openings over From ends maximum: ' " ' " wide.

Line 3 Roof Loads: Minimum size piers: Location (from front): Minimum size piers: Location (continued):

Line 4 Roof Loads: Minimum size piers: Location (from front): Minimum size piers: Location (continued):


K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-53_MH_HCD_WUI_Regulations_rev'd_3.7.2014_AKM.doc

Page 1 of 1

ATTENTION!

IMPORTANT ANNOUNCEMENT ON MOBILE/MODULAR/MANUFACTURED HOMES

Butte County requires that all

mobile/modular/manufactured homes being installed on private property be manufactured

after June 1976 or HUD approved. In additional if your private property is located in the Wildland Urban Interface (WUI) Areas (SRA -

State Responsibility Areas) effective September 1, 2009 the Department of Housing and Community

Development adopted new regulations the following may apply to you:

If the mobile/modular home to be installed is:

1. Built after January 1, 2008. No modifications are required.

2. All other year models constructed after June 1976 can be installed but may need to be modified to meet the Department of Housing and Community Development regulations for installation in WUI areas, these modifications may include any or all of the following: a. Roofing, b. Eave/Attic Venting, (**See paragraph below)

**For homes built prior to December 31, 2007, permits may be required from HCD to bring the mobile/modular up to current codes. Contact HCD directly at 916-255-2501 or visit their website at www.hcd.ca.gov to determine permit requirements and costs. Once the home has been modified you will be issued a label to install in the mobile to indicate it has been modified and complies with current regulations. The Butte County building department can then proceed with the mobile home installation permit.



FORM NO

DBP-53

http://www.hcd.ca.gov/

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-54_MH_Dates_4.29.13_rev'd_3.7.2014_AKM.doc

Page 1 of 1

Below is a list of important dates for regulations concerning mobile/manufactured homes as well as enforcement dates for Butte County. September 1, 1958: First standards for plumbing, heat producing and electrical equipment in mobile homes, recreational vehicles, and travel trailers. September 15, 1971: First standards for construction and fire safety in mobile homes and commercial coaches. April 21, 1972: Enforcement effective for mobile home utility permits. January 20, 1975: Enforcement effective for mobile home installation permits. June 15, 1976: Effective date for the Federal Mobile Home Construction and Safety Standards Act of 1974 (42 U.S. Section 5401 et seq.) – National manufactured home standard adopted by U.S. Department of Housing and Urban Development preempted all state and local standards and created HUD labeling. Mobile home does not include recreational vehicle, commercial coach, or factory built housing as defined in California State Health and Safety Code Section 19971. The label should read as follows: AS EVIDENCED BY THIS LABEL NO._______, THE MANUFACTURER CERTIFIES THAT THIS MOBILE HOME HAS BEEN INSPECTED IN ACCORDANCE WITH THE REQUIREMENTS OF THE DEPARTMENT OF HOUSING AND URBAN DEVELOPMENT AND TO THE BEST OF THE MANUFACTURER’S KNOWLEDGE AND BELIEF, IS CONSTRUCTED IN CONFORMANCE WITH THE FEDERAL MOBILE HOME CONSTRUCTION AND SAFETY STANDARDS IN EFFECT ON THE DATE OF THE MANUFACTURE. SEE DATA PLATE. September 20, 1994: Mobile home tie down requirements enforcement began. March 11, 1997: Mobile homes requirement to meet the Federal Mobile Home Construction and Safety Standards Act of 1974 (newer than June 1976).



FORM NO

DBP-54

SIGNIFICANT MOBILE/MANUFACTURED HOME DATES

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-55_Mobile-Manufactured_Home_Utility_Guidelines_3.12.2014_AKM.doc

Page 1 of 3

MOBILE/MANUFACTURED HOME UTILITY GUIDELINES

UTILITY CONNECTIONS FOR MOBILE HOMES/MANUFACTURED HOMES, AND COMMERCIAL MODULARS ON FOUNDATION SYSTEM. When a foundation system is installed pursuant to section 18551 of the Health and Safety Code, utility connections shall comply with the requirements of Title 25, or at the discretion of the owner, the connections may be installed as required for permanent residential buildings in compliance with the California Plumbing Code and the California Electric Code [1333.5(a)]. Whenever a commercial modular is installed, the utility connections shall comply with the California Plumbing Code and California Electrical Code [1333.5(b)].Utility connections shall be located within 4 feet of the Mobile Home/Manufactured Home (See Area "N' below). Sewer and water connections may be located under the Mobile Home/Manufactured Home within 18 inches of the outside wall (See Area "B" below). [1184, 1222, 1254(e), and 1274].

ELECTRICAL Equipment installed to supply electrical to a Mobile Home/Manufactured Home shall be rated at not less than 100 amperes and shall be listed and labeled "Service Equipment” [1180] Equipment to supply electrical power to a Mobile Home/Manufactured Home shall be located within 4 feet of the home or the proposed location of the home [1184]. Additional loads (well pumps, garage, shops, etc.) require additional power. Approved Mobile Home/manufactured Home lot service equipment shall be stabilized by concrete not less than 3 1/2 inches thick and surrounding the equipment base by not less than 6 inches. The lot service equipment shall be secured to a 4 X 4 redwood or pressure treated post or equivalent installed not less than 2 feet into the earth [1182].



FORM NO

DBP-55


Page 2 of 3

36” MIN. CLEARANCE

GAS

The lot gas outlet shall terminate within 4 feet outside of the home or proposed location of the home [1222(a)]. Gas meters shall not be installed closer than 3 feet from sources of ignition [1226(b)]. All gas piping installed below ground shall have a minimum earth cover of 18 inches. Gas piping shall not be installed underground beneath buildings or that portion of the lot reserved for the location of the home or any accessory buildings [1216]. Underground Liquefied Petroleum Gas shall require a test of 10 pounds for a minimum of 15 minutes.

3” CONCRETE PAD

‐‐‐COPPER GROUND‐‐‐ CONDUCTOR WITH

PROTECTED GROUND CLAMP

1‐‐‐‐‐‐‐‐‐‐‐ 6” GROUND ROD ‐‐‐‐‐‐‐‐‐<‐‐‐‐ 1

WITH METER W/O METER

--------FLEX CONNECTOR--------

6” MIN

18” MIN


Page 3 of 3

WATER SUPPLY AND DRAIN CONNECTOR

Each lot shall be provided with potable water service. The water service outlet riser shall be not less than 3/4 inch nominal pipe size [1274(a)]. The lot water outlet shall be located within 4 feet of the outside of the unit, or under the unit within 18 inches of the exterior wall of the unit [1274(b)]. A pressure test of a minimum of 50 pounds or working pressure shall be required. Each lot shall be provided with a drain inlet not less than 3 inches in diameter and shall be connected to an approved sewage disposal system [1254(a)]. Each drain inlet shall be protected from movement by being encased in a concrete slab not less than 3 1/2 inches thick and which surrounds the inlet by not less than 6 inches on any side [1254(c)]. The lot drain inlet shall be located within 4 feet of the outside of the unit, or under the unit within 18 inches of the exterior wall of the unit [1254(e)].

SEWER OUTLET WATER SUPPLY

FLEX CONNECTOR

D-----SHUT OFF VALVE

FLEX COUPLING

3” MAX

---MOBILE

3” CONCRETE PAD DRAIN TO SEWER

OR SEPTIC TANK

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-59_Mobile_Manufactured_Home_Check_List_rev'd_3.7.2014_AKM.doc

Page 1 of 1

MOBILE/MANUFACTURE HOME CHECK LIST

Owner: _________________________________________________ Address and/or APN: _____________________________________ Date: __________________________________________________ Please check of each item or mark N/A. Applicant Permit Tech Item ______ ______ 3 site plans (one 11” x 17” for scanning) ______ ______ 1 installation manual (if available) ______ ______ Marriage line information from manufactured/mobile home manufacturer if home is larger than a single wide, in duplicate ______ ______ Manufactured/Mobile home manufacturer’s floor plan in triplicate, if floor plan is not available it can be drawn by applicant. Floor plan requires dimensions of manufactured/mobile home, indicate all windows and exits, label each room and include any interior fixtures. (One floor plan must be 11” x 17 for scanning). ______ ______ State approved or engineered tie down or foundation plans in duplicate. ______ ______ Butte County Manufactured Home Support Information sheet (form DBP-52) completed with information from manufactured/mobile home manufacturer’s installation instructions. ______ ______ Flood Elevation Certificate, in duplicate, wet stamped and signed. ______ ______ A copy of the creation deed may be required for the parcel if the parcel is undeveloped (vacant and never been built on). ______ ______ If on permanent foundation system: _____ A copy of the current recorded grant deed with the legal description ______ Title or Registration of the manufactured/mobile home or if it is a new manufactured/mobile home a copy of the Manufacturer’s Certificate of Origin (MCO)



FORM NO

DBP-59

K:\NEW_WEBSITE\Building\Building Forms & Documents\2014\2014 Forms - Completed\DBP\DBP-58_MH_Retrofit_Foundation_System_rev'd_3.7.2014_AKM.doc

Page 1 of 1

When applying for a permit for a permanent foundation system under an existing mobile/manufactured home, this process eliminates the mobile/manufactured home title and registration and makes it real property. It is then assessed each year with the parcel by the County tax assessor same as a stick built home. This process eliminates the registration each year of the mobile/manufactured home as personal property through the Housing Community Development (HCD). An HCD Form 433A is created by the Building Department and then recorded by the applicant after the final inspection of the permit for the mobile/manufactured home. The recorded HCD Form 433A and a certificate of occupancy, an HCD 513C, is then sent to HCD by the Building Department thus eliminating the tile to the mobile/manufactured home. Completed Butte County Department of Developments Services building permit application (form DBP-1). Please furnish assessor’s parcel number for the proposed location. 3 site plans signed by the preparer of the plans (form DBP-2). Paper to draw site plans and site plan submittal requirements (form DBP-3) are available at the Development Services counter. At least one site plan must be 11” x 17”. NOTE: If the parcel is in the City of Biggs, the site plan must be reviewed and approved prior to submitting your building permit application. They can be reached at (530)868-5447. State approved or engineered tie down or foundation plans in duplicate

A copy of the current recorded grant deed with the legal description and a copy of the Title or Registration of the manufactured/mobile home.



FORM NO

DBP-58

BUILDING PERMIT APPLICATION REQUIREMENTS FOR EXISTING MOBILE/MANUFACTURED HOME

EXISTING SITE TO BE PLACED ON A PERMANENT FOUNDATION SYSTEM (Retro-Fit)

BUILDING PERMIT SUBMITTAL REQUIREMENTS … · BUILDING PERMIT SUBMITTAL REQUIREMENTS ... determine...

Documents

Transcript of BUILDING PERMIT SUBMITTAL REQUIREMENTS … · BUILDING PERMIT SUBMITTAL REQUIREMENTS ... determine...